diff options
Diffstat (limited to 'Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt | 69 |
1 files changed, 69 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt new file mode 100644 index 000000000000..e8d8086a7ae9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt @@ -0,0 +1,69 @@ +Socionext UniPhier USB3 High-Speed (HS) PHY + +This describes the devicetree bindings for PHY interfaces built into +USB3 controller implemented on Socionext UniPhier SoCs. +Although the controller includes High-Speed PHY and Super-Speed PHY, +this describes about High-Speed PHY. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-pro4-usb3-hsphy" - for Pro4 SoC + "socionext,uniphier-pxs2-usb3-hsphy" - for PXs2 SoC + "socionext,uniphier-ld20-usb3-hsphy" - for LD20 SoC + "socionext,uniphier-pxs3-usb3-hsphy" - for PXs3 SoC +- reg: Specifies offset and length of the register set for the device. +- #phy-cells: Should be 0. +- clocks: A list of phandles to the clock gate for USB3 glue layer. + According to the clock-names, appropriate clocks are required. +- clock-names: Should contain the following: + "gio", "link" - for Pro4 SoC + "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional. + "phy", "link" - for others +- resets: A list of phandles to the reset control for USB3 glue layer. + According to the reset-names, appropriate resets are required. +- reset-names: Should contain the following: + "gio", "link" - for Pro4 SoC + "phy", "link" - for others + +Optional properties: +- vbus-supply: A phandle to the regulator for USB VBUS. +- nvmem-cells: Phandles to nvmem cell that contains the trimming data. + Available only for HS-PHY implemented on LD20 and PXs3, and + if unspecified, default value is used. +- nvmem-cell-names: Should be the following names, which correspond to + each nvmem-cells. + All of the 3 parameters associated with the following names are + required for each port, if any one is omitted, the trimming data + of the port will not be set at all. + "rterm", "sel_t", "hs_i" - Each cell name for phy parameters + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + + usb-glue@65b00000 { + compatible = "socionext,uniphier-ld20-dwc3-glue", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x65b00000 0x400>; + + usb_vbus0: regulator { + ... + }; + + usb_hsphy0: hs-phy@200 { + compatible = "socionext,uniphier-ld20-usb3-hsphy"; + reg = <0x200 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy"; + clocks = <&sys_clk 14>, <&sys_clk 16>; + reset-names = "link", "phy"; + resets = <&sys_rst 14>, <&sys_rst 16>; + vbus-supply = <&usb_vbus0>; + nvmem-cell-names = "rterm", "sel_t", "hs_i"; + nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>, + <&usb_hs_i0>; + }; + ... + }; |