diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt | 22 |
1 files changed, 9 insertions, 13 deletions
diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt index 84fdc422792e..b6acbe694ffb 100644 --- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt @@ -18,7 +18,6 @@ Required properties: - reg-names: Must be - "elbi" External local bus interface registers - "cfg" Meson specific registers - - "phy" Meson PCIE PHY registers for AXG SoC Family - "config" PCIe configuration space - reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal. - clocks: Must contain an entry for each entry in clock-names. @@ -26,13 +25,13 @@ Required properties: - "pclk" PCIe GEN 100M PLL clock - "port" PCIe_x(A or B) RC clock gate - "general" PCIe Phy clock - - "mipi" PCIe_x(A or B) 100M ref clock gate for AXG SoC Family - resets: phandle to the reset lines. -- reset-names: must contain "phy" "port" and "apb" - - "phy" Share PHY reset for AXG SoC Family +- reset-names: must contain "port" and "apb" - "port" Port A or B reset - "apb" Share APB reset -- phys: should contain a phandle to the shared phy for G12A SoC Family +- phys: should contain a phandle to the PCIE phy +- phy-names: must contain "pcie" + - device_type: should be "pci". As specified in designware-pcie.txt @@ -43,9 +42,8 @@ Example configuration: compatible = "amlogic,axg-pcie", "snps,dw-pcie"; reg = <0x0 0xf9800000 0x0 0x400000 0x0 0xff646000 0x0 0x2000 - 0x0 0xff644000 0x0 0x2000 0x0 0xf9f00000 0x0 0x100000>; - reg-names = "elbi", "cfg", "phy", "config"; + reg-names = "elbi", "cfg", "config"; reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>; interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>; #interrupt-cells = <1>; @@ -58,17 +56,15 @@ Example configuration: ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>; clocks = <&clkc CLKID_USB - &clkc CLKID_MIPI_ENABLE &clkc CLKID_PCIE_A &clkc CLKID_PCIE_CML_EN0>; clock-names = "general", - "mipi", "pclk", "port"; - resets = <&reset RESET_PCIE_PHY>, - <&reset RESET_PCIE_A>, + resets = <&reset RESET_PCIE_A>, <&reset RESET_PCIE_APB>; - reset-names = "phy", - "port", + reset-names = "port", "apb"; + phys = <&pcie_phy>; + phy-names = "pcie"; }; |