diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
| -rw-r--r-- | Documentation/devicetree/bindings/net/ethernet.txt | 4 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/net/sff,sfp.txt | 76 |
2 files changed, 80 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index 7da86f22a13b..2974e63ba311 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -1,5 +1,9 @@ The following properties are common to the Ethernet controllers: +NOTE: All 'phy*' properties documented below are Ethernet specific. For the +generic PHY 'phys' property, see +Documentation/devicetree/bindings/phy/phy-bindings.txt. + - local-mac-address: array of 6 bytes, specifies the MAC address that was assigned to the network device; - mac-address: array of 6 bytes, specifies the MAC address that was last used by diff --git a/Documentation/devicetree/bindings/net/sff,sfp.txt b/Documentation/devicetree/bindings/net/sff,sfp.txt new file mode 100644 index 000000000000..60e970ce10ee --- /dev/null +++ b/Documentation/devicetree/bindings/net/sff,sfp.txt @@ -0,0 +1,76 @@ +Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP) +Transceiver + +Required properties: + +- compatible : must be "sff,sfp" + +Optional Properties: + +- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial + interface + +- mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) + module presence input gpio signal, active (module absent) high + +- los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal + Indication input gpio signal, active (signal lost) high + +- tx-fault-gpios : GPIO phandle and a specifier of the Module Transmitter + Fault input gpio signal, active (fault condition) high + +- tx-disable-gpios : GPIO phandle and a specifier of the Transmitter Disable + output gpio signal, active (Tx disable) high + +- rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate + Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate + +- rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate + Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high: + high Tx rate + +Example #1: Direct serdes to SFP connection + +sfp_eth3: sfp-eth3 { + compatible = "sff,sfp"; + i2c-bus = <&sfp_1g_i2c>; + los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>; + tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>; +}; + +&cps_emac3 { + phy-names = "comphy"; + phys = <&cps_comphy5 0>; + sfp = <&sfp_eth3>; +}; + +Example #2: Serdes to PHY to SFP connection + +sfp_eth0: sfp-eth0 { + compatible = "sff,sfp"; + i2c-bus = <&sfpp0_i2c>; + los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cps_sfpp0_pins>; + tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>; +}; + +p0_phy: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + pinctrl-names = "default"; + pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>; + reg = <0>; + interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>; + sfp = <&sfp_eth0>; +}; + +&cpm_eth0 { + phy = <&p0_phy>; + phy-mode = "10gbase-kr"; +}; |