diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
| -rw-r--r-- | Documentation/devicetree/bindings/net/mdio-mux-meson-g12a.txt | 48 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/net/phy.txt | 6 |
2 files changed, 54 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/mdio-mux-meson-g12a.txt b/Documentation/devicetree/bindings/net/mdio-mux-meson-g12a.txt new file mode 100644 index 000000000000..3a96cbed9294 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux-meson-g12a.txt @@ -0,0 +1,48 @@ +Properties for the MDIO bus multiplexer/glue of Amlogic G12a SoC family. + +This is a special case of a MDIO bus multiplexer. It allows to choose between +the internal mdio bus leading to the embedded 10/100 PHY or the external +MDIO bus. + +Required properties in addition to the generic multiplexer properties: +- compatible : amlogic,g12a-mdio-mux +- reg: physical address and length of the multiplexer/glue registers +- clocks: list of clock phandle, one for each entry clock-names. +- clock-names: should contain the following: + * "pclk" : peripheral clock. + * "clkin0" : platform crytal + * "clkin1" : SoC 50MHz MPLL + +Example : + +mdio_mux: mdio-multiplexer@4c000 { + compatible = "amlogic,g12a-mdio-mux"; + reg = <0x0 0x4c000 0x0 0xa4>; + clocks = <&clkc CLKID_ETH_PHY>, + <&xtal>, + <&clkc CLKID_MPLL_5OM>; + clock-names = "pclk", "clkin0", "clkin1"; + mdio-parent-bus = <&mdio0>; + #address-cells = <1>; + #size-cells = <0>; + + ext_mdio: mdio@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + int_mdio: mdio@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + internal_ephy: ethernet-phy@8 { + compatible = "ethernet-phy-id0180.3301", + "ethernet-phy-ieee802.3-c22"; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <8>; + max-speed = <100>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index 17c1d2bd00f6..9b9e5b1765dd 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -51,6 +51,10 @@ Optional Properties: to ensure the integrated PHY is used. The absence of this property indicates the muxers should be configured so that the external PHY is used. +- resets: The reset-controller phandle and specifier for the PHY reset signal. + +- reset-names: Must be "phy" for the PHY reset signal. + - reset-gpios: The GPIO phandle and specifier for the PHY reset signal. - reset-assert-us: Delay after the reset was asserted in microseconds. @@ -67,6 +71,8 @@ ethernet-phy@0 { interrupts = <35 IRQ_TYPE_EDGE_RISING>; reg = <0>; + resets = <&rst 8>; + reset-names = "phy"; reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; reset-assert-us = <1000>; reset-deassert-us = <2000>; |