diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mtd/atmel-nand.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/atmel-nand.txt | 107 |
1 files changed, 106 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index 3e7ee99d3949..f6bee57e453a 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -1,4 +1,109 @@ -Atmel NAND flash +Atmel NAND flash controller bindings + +The NAND flash controller node should be defined under the EBI bus (see +Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt). +One or several NAND devices can be defined under this NAND controller. +The NAND controller might be connected to an ECC engine. + +* NAND controller bindings: + +Required properties: +- compatible: should be one of the following + "atmel,at91rm9200-nand-controller" + "atmel,at91sam9260-nand-controller" + "atmel,at91sam9261-nand-controller" + "atmel,at91sam9g45-nand-controller" + "atmel,sama5d3-nand-controller" +- ranges: empty ranges property to forward EBI ranges definitions. +- #address-cells: should be set to 2. +- #size-cells: should be set to 1. +- atmel,nfc-io: phandle to the NFC IO block. Only required for sama5d3 + controllers. +- atmel,nfc-sram: phandle to the NFC SRAM block. Only required for sama5d3 + controllers. + +Optional properties: +- ecc-engine: phandle to the PMECC block. Only meaningful if the SoC embeds + a PMECC engine. + +* NAND device/chip bindings: + +Required properties: +- reg: describes the CS lines assigned to the NAND device. If the NAND device + exposes multiple CS lines (multi-dies chips), your reg property will + contain X tuples of 3 entries. + 1st entry: the CS line this NAND chip is connected to + 2nd entry: the base offset of the memory region assigned to this + device (always 0) + 3rd entry: the memory region size (always 0x800000) + +Optional properties: +- rb-gpios: the GPIO(s) used to check the Ready/Busy status of the NAND. +- cs-gpios: the GPIO(s) used to control the CS line. +- det-gpios: the GPIO used to detect if a Smartmedia Card is present. +- atmel,rb: an integer identifying the native Ready/Busy pin. Only meaningful + on sama5 SoCs. + +All generic properties described in +Documentation/devicetree/bindings/mtd/{common,nand}.txt also apply to the NAND +device node, and NAND partitions should be defined under the NAND node as +described in Documentation/devicetree/bindings/mtd/partition.txt. + +* ECC engine (PMECC) bindings: + +Required properties: +- compatible: should be one of the following + "atmel,at91sam9g45-pmecc" + "atmel,sama5d4-pmecc" + "atmel,sama5d2-pmecc" +- reg: should contain 2 register ranges. The first one is pointing to the PMECC + block, and the second one to the PMECC_ERRLOC block. + +Example: + + pmecc: ecc-engine@ffffc070 { + compatible = "atmel,at91sam9g45-pmecc"; + reg = <0xffffc070 0x490>, + <0xffffc500 0x100>; + }; + + ebi: ebi@10000000 { + compatible = "atmel,sama5d3-ebi"; + #address-cells = <2>; + #size-cells = <1>; + atmel,smc = <&hsmc>; + reg = <0x10000000 0x10000000 + 0x40000000 0x30000000>; + ranges = <0x0 0x0 0x10000000 0x10000000 + 0x1 0x0 0x40000000 0x10000000 + 0x2 0x0 0x50000000 0x10000000 + 0x3 0x0 0x60000000 0x10000000>; + clocks = <&mck>; + + nand_controller: nand-controller { + compatible = "atmel,sama5d3-nand-controller"; + atmel,nfc-sram = <&nfc_sram>; + atmel,nfc-io = <&nfc_io>; + ecc-engine = <&pmecc>; + #address-cells = <2>; + #size-cells = <1>; + ranges; + + nand@3 { + reg = <0x3 0x0 0x800000>; + atmel,rb = <0>; + + /* + * Put generic NAND/MTD properties and + * subnodes here. + */ + }; + }; + }; + +----------------------------------------------------------------------- + +Deprecated bindings (should not be used in new device trees): Required properties: - compatible: The possible values are: |