1 files changed, 0 insertions, 135 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt
deleted file mode 100644
index 75ba25d062e1..000000000000
--- a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.txt
+++ /dev/null
@@ -1,135 +0,0 @@
-STMicroelectronics STM32 DFSDM ADC device driver
-
-
-STM32 DFSDM ADC is a sigma delta analog-to-digital converter dedicated to
-interface external sigma delta modulators to STM32 micro controllers.
-It is mainly targeted for:
-- Sigma delta modulators (motor control, metering...)
-- PDM microphones (audio digital microphone)
-
-It features up to 8 serial digital interfaces (SPI or Manchester) and
-up to 4 filters on stm32h7 or 6 filters on stm32mp1.
-
-Each child node match with a filter instance.
-
-Contents of a STM32 DFSDM root node:
-------------------------------------
-Required properties:
-- compatible: Should be one of:
-  "st,stm32h7-dfsdm"
-  "st,stm32mp1-dfsdm"
-- reg: Offset and length of the DFSDM block register set.
-- clocks: IP and serial interfaces clocking. Should be set according
-		to rcc clock ID and "clock-names".
-- clock-names: Input clock name "dfsdm" must be defined,
-		"audio" is optional. If defined CLKOUT is based on the audio
-		clock, else "dfsdm" is used.
-- #interrupt-cells = <1>;
-- #address-cells = <1>;
-- #size-cells = <0>;
-
-Optional properties:
-- spi-max-frequency: Requested only for SPI master mode.
-		  SPI clock OUT frequency (Hz). This clock must be set according
-		  to "clock" property. Frequency must be a multiple of the rcc
-		  clock frequency. If not, SPI CLKOUT frequency will not be
-		  accurate.
-- pinctrl-names:	Set to "default".
-- pinctrl-0:		List of phandles pointing to pin configuration
-			nodes to set pins in mode of operation for dfsdm
-			on external pin.
-
-Contents of a STM32 DFSDM child nodes:
---------------------------------------
-
-Required properties:
-- compatible: Must be:
-	"st,stm32-dfsdm-adc" for sigma delta ADCs
-	"st,stm32-dfsdm-dmic" for audio digital microphone.
-- reg: Specifies the DFSDM filter instance used.
-	Valid values are from 0 to 3 on stm32h7, 0 to 5 on stm32mp1.
-- interrupts: IRQ lines connected to each DFSDM filter instance.
-- st,adc-channels:	List of single-ended channels muxed for this ADC.
-			valid values:
-				"st,stm32h7-dfsdm" compatibility: 0 to 7.
-- st,adc-channel-names:	List of single-ended channel names.
-- st,filter-order:  SinC filter order from 0 to 5.
-			0: FastSinC
-			[1-5]: order 1 to 5.
-			For audio purpose it is recommended to use order 3 to 5.
-- #io-channel-cells = <1>: See the IIO bindings section "IIO consumers".
-
-Required properties for "st,stm32-dfsdm-adc" compatibility:
-- io-channels: From common IIO binding. Used to pipe external sigma delta
-		modulator or internal ADC output to DFSDM channel.
-		This is not required for "st,stm32-dfsdm-pdm" compatibility as
-		PDM microphone is binded in Audio DT node.
-
-Required properties for "st,stm32-dfsdm-pdm" compatibility:
-- #sound-dai-cells: Must be set to 0.
-- dma: DMA controller phandle and DMA request line associated to the
-		filter instance (specified by the field "reg")
-- dma-names: Must be "rx"
-
-Optional properties:
-- st,adc-channel-types:	Single-ended channel input type.
-			- "SPI_R": SPI with data on rising edge (default)
-			- "SPI_F": SPI with data on falling edge
-			- "MANCH_R": manchester codec, rising edge = logic 0, falling edge = logic 1
-			- "MANCH_F": manchester codec, rising edge = logic 1, falling edge = logic 0
-- st,adc-channel-clk-src: Conversion clock source.
-			  - "CLKIN": external SPI clock (CLKIN x)
-			  - "CLKOUT": internal SPI clock (CLKOUT) (default)
-			  - "CLKOUT_F": internal SPI clock divided by 2 (falling edge).
-			  - "CLKOUT_R": internal SPI clock divided by 2 (rising edge).
-
-- st,adc-alt-channel: Must be defined if two sigma delta modulator are
-			  connected on same SPI input.
-			  If not set, channel n is connected to SPI input n.
-			  If set, channel n is connected to SPI input n + 1.
-
-- st,filter0-sync: Set to 1 to synchronize with DFSDM filter instance 0.
-		   Used for multi microphones synchronization.
-
-Example of a sigma delta adc connected on DFSDM SPI port 0
-and a pdm microphone connected on DFSDM SPI port 1:
-
-	ads1202: simple_sd_adc@0 {
-		compatible = "ads1202";
-		#io-channel-cells = <1>;
-	};
-
-	dfsdm: dfsdm@40017000 {
-		compatible = "st,stm32h7-dfsdm";
-		reg = <0x40017000 0x400>;
-		clocks = <&rcc DFSDM1_CK>;
-		clock-names = "dfsdm";
-		#interrupt-cells = <1>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		dfsdm_adc0: filter@0 {
-			compatible = "st,stm32-dfsdm-adc";
-			#io-channel-cells = <1>;
-			reg = <0>;
-			interrupts = <110>;
-			st,adc-channels = <0>;
-			st,adc-channel-names = "sd_adc0";
-			st,adc-channel-types = "SPI_F";
-			st,adc-channel-clk-src = "CLKOUT";
-			io-channels = <&ads1202 0>;
-			st,filter-order = <3>;
-		};
-		dfsdm_pdm1: filter@1 {
-			compatible = "st,stm32-dfsdm-dmic";
-			reg = <1>;
-			interrupts = <111>;
-			dmas = <&dmamux1 102 0x400 0x00>;
-			dma-names = "rx";
-			st,adc-channels = <1>;
-			st,adc-channel-names = "dmic1";
-			st,adc-channel-types = "SPI_R";
-			st,adc-channel-clk-src = "CLKOUT";
-			st,filter-order = <5>;
-		};
-	}