1 files changed, 0 insertions, 90 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
deleted file mode 100644
index 3126c3817e2a..000000000000
--- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
+++ /dev/null
@@ -1,90 +0,0 @@
-* NXP PCA953x I2C GPIO multiplexer
-
-Required properties:
- - compatible: Has to contain one of the following:
-	nxp,pca6416
-	nxp,pca9505
-	nxp,pca9534
-	nxp,pca9535
-	nxp,pca9536
-	nxp,pca9537
-	nxp,pca9538
-	nxp,pca9539
-	nxp,pca9554
-	nxp,pca9555
-	nxp,pca9556
-	nxp,pca9557
-	nxp,pca9574
-	nxp,pca9575
-	nxp,pca9698
-	nxp,pcal6416
-	nxp,pcal6524
-	nxp,pcal9535
-	nxp,pcal9555a
-	maxim,max7310
-	maxim,max7312
-	maxim,max7313
-	maxim,max7315
-	ti,pca6107
-	ti,pca9536
-	ti,tca6408
-	ti,tca6416
-	ti,tca6424
-	ti,tca9539
-	ti,tca9554
-	onnn,cat9554
-	onnn,pca9654
-	exar,xra1202
- - gpio-controller: if used as gpio expander.
- - #gpio-cells: if used as gpio expander.
- - interrupt-controller: if to be used as interrupt expander.
- - #interrupt-cells: if to be used as interrupt expander.
-
-Optional properties:
- - interrupts: interrupt specifier for the device's interrupt output.
- - reset-gpios: GPIO specification for the RESET input. This is an
-		active low signal to the PCA953x.
- - vcc-supply:	power supply regulator.
-
-Example:
-
-
-	gpio@20 {
-		compatible = "nxp,pca9505";
-		reg = <0x20>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pca9505>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		interrupt-parent = <&gpio3>;
-		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
-	};
-
-
-Example with Interrupts:
-
-
-	gpio99: gpio@22 {
-		compatible = "nxp,pcal6524";
-		reg = <0x22>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;	/* gpio6_161 */
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		vcc-supply = <&vdds_1v8_main>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-line-names =
-			"hdmi-ct-hpd", "hdmi.ls-oe", "p02", "p03", "vibra", "fault2", "p06", "p07",
-			"en-usb", "en-host1", "en-host2", "chg-int", "p14", "p15", "mic-int", "en-modem",
-			"shdn-hs-amp", "chg-status+red", "green", "blue", "en-esata", "fault1", "p26", "p27";
-	};
-
-	ts3a227@3b {
-		compatible = "ti,ts3a227e";
-		reg = <0x3b>;
-		interrupt-parent = <&gpio99>;
-		interrupts = <14 IRQ_TYPE_EDGE_RISING>;
-		ti,micbias = <0>;	/* 2.1V */
-	};
-