summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/display/exynos/exynos_dp.txt')
-rw-r--r--Documentation/devicetree/bindings/display/exynos/exynos_dp.txt120
1 files changed, 120 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
new file mode 100644
index 000000000000..64693f2ebc51
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
@@ -0,0 +1,120 @@
+The Exynos display port interface should be configured based on
+the type of panel connected to it.
+
+We use two nodes:
+ -dp-controller node
+ -dptx-phy node(defined inside dp-controller node)
+
+For the DP-PHY initialization, we use the dptx-phy node.
+Required properties for dptx-phy: deprecated, use phys and phy-names
+ -reg: deprecated
+ Base address of DP PHY register.
+ -samsung,enable-mask: deprecated
+ The bit-mask used to enable/disable DP PHY.
+
+For the Panel initialization, we read data from dp-controller node.
+Required properties for dp-controller:
+ -compatible:
+ should be "samsung,exynos5-dp".
+ -reg:
+ physical base address of the controller and length
+ of memory mapped region.
+ -interrupts:
+ interrupt combiner values.
+ -clocks:
+ from common clock binding: handle to dp clock.
+ -clock-names:
+ from common clock binding: Shall be "dp".
+ -interrupt-parent:
+ phandle to Interrupt combiner node.
+ -phys:
+ from general PHY binding: the phandle for the PHY device.
+ -phy-names:
+ from general PHY binding: Should be "dp".
+ -samsung,color-space:
+ input video data format.
+ COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2
+ -samsung,dynamic-range:
+ dynamic range for input video data.
+ VESA = 0, CEA = 1
+ -samsung,ycbcr-coeff:
+ YCbCr co-efficients for input video.
+ COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1
+ -samsung,color-depth:
+ number of bits per colour component.
+ COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3
+ -samsung,link-rate:
+ link rate supported by the panel.
+ LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A
+ -samsung,lane-count:
+ number of lanes supported by the panel.
+ LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4
+ - display-timings: timings for the connected panel as described by
+ Documentation/devicetree/bindings/display/display-timing.txt
+
+Optional properties for dp-controller:
+ -interlaced:
+ interlace scan mode.
+ Progressive if defined, Interlaced if not defined
+ -vsync-active-high:
+ VSYNC polarity configuration.
+ High if defined, Low if not defined
+ -hsync-active-high:
+ HSYNC polarity configuration.
+ High if defined, Low if not defined
+ -samsung,hpd-gpio:
+ Hotplug detect GPIO.
+ Indicates which GPIO should be used for hotplug
+ detection
+ -video interfaces: Device node can contain video interface port
+ nodes according to [1].
+
+[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+SOC specific portion:
+ dp-controller {
+ compatible = "samsung,exynos5-dp";
+ reg = <0x145b0000 0x10000>;
+ interrupts = <10 3>;
+ interrupt-parent = <&combiner>;
+ clocks = <&clock 342>;
+ clock-names = "dp";
+
+ phys = <&dp_phy>;
+ phy-names = "dp";
+ };
+
+Board Specific portion:
+ dp-controller {
+ samsung,color-space = <0>;
+ samsung,dynamic-range = <0>;
+ samsung,ycbcr-coeff = <0>;
+ samsung,color-depth = <1>;
+ samsung,link-rate = <0x0a>;
+ samsung,lane-count = <4>;
+
+ display-timings {
+ native-mode = <&lcd_timing>;
+ lcd_timing: 1366x768 {
+ clock-frequency = <70589280>;
+ hactive = <1366>;
+ vactive = <768>;
+ hfront-porch = <40>;
+ hback-porch = <40>;
+ hsync-len = <32>;
+ vback-porch = <10>;
+ vfront-porch = <12>;
+ vsync-len = <6>;
+ };
+ };
+
+ ports {
+ port@0 {
+ dp_out: endpoint {
+ remote-endpoint = <&bridge_in>;
+ };
+ };
+ };
+ };