1 files changed, 0 insertions, 110 deletions
diff --git a/Documentation/devicetree/bindings/display/arm,pl11x.txt b/Documentation/devicetree/bindings/display/arm,pl11x.txt
deleted file mode 100644
index 3f977e72a200..000000000000
--- a/Documentation/devicetree/bindings/display/arm,pl11x.txt
+++ /dev/null
@@ -1,110 +0,0 @@
-* ARM PrimeCell Color LCD Controller PL110/PL111
-
-See also Documentation/devicetree/bindings/arm/primecell.yaml
-
-Required properties:
-
-- compatible: must be one of:
-	"arm,pl110", "arm,primecell"
-	"arm,pl111", "arm,primecell"
-
-- reg: base address and size of the control registers block
-
-- interrupt-names: either the single entry "combined" representing a
-	combined interrupt output (CLCDINTR), or the four entries
-	"mbe", "vcomp", "lnbu", "fuf" representing the individual
-	CLCDMBEINTR, CLCDVCOMPINTR, CLCDLNBUINTR, CLCDFUFINTR interrupts
-
-- interrupts: contains an interrupt specifier for each entry in
-	interrupt-names
-
-- clock-names: should contain "clcdclk" and "apb_pclk"
-
-- clocks: contains phandle and clock specifier pairs for the entries
-	in the clock-names property. See
-	Documentation/devicetree/bindings/clock/clock-bindings.txt
-
-Optional properties:
-
-- memory-region: phandle to a node describing memory (see
-	Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt)
-	to be used for the framebuffer; if not present, the framebuffer
-	may be located anywhere in the memory
-
-- max-memory-bandwidth: maximum bandwidth in bytes per second that the
-	cell's memory interface can handle; if not present, the memory
-	interface is fast enough to handle all possible video modes
-
-Required sub-nodes:
-
-- port: describes LCD panel signals, following the common binding
-	for video transmitter interfaces; see
-	Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Deprecated properties:
-	The port's endbpoint subnode had this, now deprecated property
-	in the past. Drivers should be able to survive without it:
-
-	- arm,pl11x,tft-r0g0b0-pads: an array of three 32-bit values,
-		defining the way CLD pads are wired up; first value
-		contains index of the "CLD" external pin (pad) used
-		as R0 (first bit of the red component), second value
-	        index of the pad used as G0, third value index of the
-		pad used as B0, see also "LCD panel signal multiplexing
-		details" paragraphs in the PL110/PL111 Technical
-		Reference Manuals; this implicitly defines available
-		color modes, for example:
-		- PL111 TFT 4:4:4 panel:
-			arm,pl11x,tft-r0g0b0-pads = <4 15 20>;
-		- PL110 TFT (1:)5:5:5 panel:
-			arm,pl11x,tft-r0g0b0-pads = <1 7 13>;
-		- PL111 TFT (1:)5:5:5 panel:
-			arm,pl11x,tft-r0g0b0-pads = <3 11 19>;
-		- PL111 TFT 5:6:5 panel:
-			arm,pl11x,tft-r0g0b0-pads = <3 10 19>;
-		- PL110 and PL111 TFT 8:8:8 panel:
-			arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
-		- PL110 and PL111 TFT 8:8:8 panel, R & B components swapped:
-			arm,pl11x,tft-r0g0b0-pads = <16 8 0>;
-
-
-Example:
-
-	clcd@10020000 {
-		compatible = "arm,pl111", "arm,primecell";
-		reg = <0x10020000 0x1000>;
-		interrupt-names = "combined";
-		interrupts = <0 44 4>;
-		clocks = <&oscclk1>, <&oscclk2>;
-		clock-names = "clcdclk", "apb_pclk";
-		max-memory-bandwidth = <94371840>; /* Bps, 1024x768@60 16bpp */
-
-		port {
-			clcd_pads: endpoint {
-				remote-endpoint = <&clcd_panel>;
-			};
-		};
-
-	};
-
-	panel {
-		compatible = "panel-dpi";
-
-		port {
-			clcd_panel: endpoint {
-				remote-endpoint = <&clcd_pads>;
-			};
-		};
-
-		panel-timing {
-			clock-frequency = <25175000>;
-			hactive = <640>;
-			hback-porch = <40>;
-			hfront-porch = <24>;
-			hsync-len = <96>;
-			vactive = <480>;
-			vback-porch = <32>;
-			vfront-porch = <11>;
-			vsync-len = <2>;
-		};
-	};