diff options
Diffstat (limited to 'Documentation/devicetree/bindings/devfreq')
| -rw-r--r-- | Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt | 205 |
1 files changed, 104 insertions, 101 deletions
diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt index fc2bcbe26b1e..1b93b33c7d38 100644 --- a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt +++ b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt @@ -1,14 +1,14 @@ -* Rockchip rk3399 DMC(Dynamic Memory Controller) device +* Rockchip rk3399 DMC (Dynamic Memory Controller) device Required properties: - compatible: Must be "rockchip,rk3399-dmc". - devfreq-events: Node to get DDR loading, Refer to - Documentation/devicetree/bindings/devfreq/ + Documentation/devicetree/bindings/devfreq/event/ rockchip-dfi.txt -- interrupts: The interrupt number to the CPU. The interrupt - specifier format depends on the interrupt controller. - It should be DCF interrupts, when DDR dvfs finish, - it will happen. +- interrupts: The CPU interrupt number. The interrupt specifier + format depends on the interrupt controller. + It should be a DCF interrupt. When DDR DVFS finishes + a DCF interrupt is triggered. - clocks: Phandles for clock specified in "clock-names" property - clock-names : The name of clock used by the DFI, must be "pclk_ddr_mon"; @@ -17,139 +17,142 @@ Required properties: - center-supply: DMC supply node. - status: Marks the node enabled/disabled. -Following properties are ddr timing: +Following properties relate to DDR timing: - rockchip,dram_speed_bin : Value reference include/dt-bindings/clock/ddr.h, - it select ddr3 cl-trp-trcd type, default value - "DDR3_DEFAULT".it must selected according to - "Speed Bin" in ddr3 datasheet, DO NOT use - smaller "Speed Bin" than ddr3 exactly is. - -- rockchip,pd_idle : Config the PD_IDLE value, defined the power-down - idle period, memories are places into power-down - mode if bus is idle for PD_IDLE DFI clocks. - -- rockchip,sr_idle : Configure the SR_IDLE value, defined the - selfrefresh idle period, memories are places - into self-refresh mode if bus is idle for - SR_IDLE*1024 DFI clocks (DFI clocks freq is - half of dram's clocks), defaule value is "0". - -- rockchip,sr_mc_gate_idle : Defined the self-refresh with memory and - controller clock gating idle period, memories - are places into self-refresh mode and memory - controller clock arg gating if bus is idle for - sr_mc_gate_idle*1024 DFI clocks. - -- rockchip,srpd_lite_idle : Defined the self-refresh power down idle - period, memories are places into self-refresh - power down mode if bus is idle for - srpd_lite_idle*1024 DFI clocks. This parameter - is for LPDDR4 only. - -- rockchip,standby_idle : Defined the standby idle period, memories are - places into self-refresh than controller, pi, - phy and dram clock will gating if bus is idle - for standby_idle * DFI clocks. - -- rockchip,dram_dll_disb_freq : It's defined the DDR3 dll bypass frequency in - MHz, when ddr freq less than DRAM_DLL_DISB_FREQ, - ddr3 dll will bypssed note: if dll was bypassed, - the odt also stop working. - -- rockchip,phy_dll_disb_freq : Defined the PHY dll bypass frequency in - MHz (Mega Hz), when ddr freq less than - DRAM_DLL_DISB_FREQ, phy dll will bypssed. - note: phy dll and phy odt are independent. - -- rockchip,ddr3_odt_disb_freq : When dram type is DDR3, this parameter defined - the odt disable frequency in MHz (Mega Hz), - when ddr frequency less then ddr3_odt_disb_freq, - the odt on dram side and controller side are + it selects the DDR3 cl-trp-trcd type. It must be + set according to "Speed Bin" in DDR3 datasheet, + DO NOT use a smaller "Speed Bin" than specified + for the DDR3 being used. + +- rockchip,pd_idle : Configure the PD_IDLE value. Defines the + power-down idle period in which memories are + placed into power-down mode if bus is idle + for PD_IDLE DFI clock cycles. + +- rockchip,sr_idle : Configure the SR_IDLE value. Defines the + self-refresh idle period in which memories are + placed into self-refresh mode if bus is idle + for SR_IDLE * 1024 DFI clock cycles (DFI + clocks freq is half of DRAM clock), default + value is "0". + +- rockchip,sr_mc_gate_idle : Defines the memory self-refresh and controller + clock gating idle period. Memories are placed + into self-refresh mode and memory controller + clock arg gating started if bus is idle for + sr_mc_gate_idle*1024 DFI clock cycles. + +- rockchip,srpd_lite_idle : Defines the self-refresh power down idle + period in which memories are placed into + self-refresh power down mode if bus is idle + for srpd_lite_idle * 1024 DFI clock cycles. + This parameter is for LPDDR4 only. + +- rockchip,standby_idle : Defines the standby idle period in which + memories are placed into self-refresh mode. + The controller, pi, PHY and DRAM clock will + be gated if bus is idle for standby_idle * DFI + clock cycles. + +- rockchip,dram_dll_dis_freq : Defines the DDR3 DLL bypass frequency in MHz. + When DDR frequency is less than DRAM_DLL_DISB_FREQ, + DDR3 DLL will be bypassed. Note: if DLL was bypassed, + the odt will also stop working. + +- rockchip,phy_dll_dis_freq : Defines the PHY dll bypass frequency in + MHz (Mega Hz). When DDR frequency is less than + DRAM_DLL_DISB_FREQ, PHY DLL will be bypassed. + Note: PHY DLL and PHY ODT are independent. + +- rockchip,ddr3_odt_dis_freq : When the DRAM type is DDR3, this parameter defines + the ODT disable frequency in MHz (Mega Hz). + when the DDR frequency is less then ddr3_odt_dis_freq, + the ODT on the DRAM side and controller side are both disabled. -- rockchip,ddr3_drv : When dram type is DDR3, this parameter define - the dram side driver stength in ohm, default +- rockchip,ddr3_drv : When the DRAM type is DDR3, this parameter defines + the DRAM side driver strength in ohms. Default value is DDR3_DS_40ohm. -- rockchip,ddr3_odt : When dram type is DDR3, this parameter define - the dram side ODT stength in ohm, default value +- rockchip,ddr3_odt : When the DRAM type is DDR3, this parameter defines + the DRAM side ODT strength in ohms. Default value is DDR3_ODT_120ohm. -- rockchip,phy_ddr3_ca_drv : When dram type is DDR3, this parameter define - the phy side CA line(incluing command line, +- rockchip,phy_ddr3_ca_drv : When the DRAM type is DDR3, this parameter defines + the phy side CA line (incluing command line, address line and clock line) driver strength. Default value is PHY_DRV_ODT_40. -- rockchip,phy_ddr3_dq_drv : When dram type is DDR3, this parameter define - the phy side DQ line(incluing DQS/DQ/DM line) - driver strength. default value is PHY_DRV_ODT_40. +- rockchip,phy_ddr3_dq_drv : When the DRAM type is DDR3, this parameter defines + the PHY side DQ line (including DQS/DQ/DM line) + driver strength. Default value is PHY_DRV_ODT_40. -- rockchip,phy_ddr3_odt : When dram type is DDR3, this parameter define the - phy side odt strength, default value is +- rockchip,phy_ddr3_odt : When the DRAM type is DDR3, this parameter defines + the PHY side ODT strength. Default value is PHY_DRV_ODT_240. -- rockchip,lpddr3_odt_disb_freq : When dram type is LPDDR3, this parameter defined - then odt disable frequency in MHz (Mega Hz), - when ddr frequency less then ddr3_odt_disb_freq, - the odt on dram side and controller side are +- rockchip,lpddr3_odt_dis_freq : When the DRAM type is LPDDR3, this parameter defines + then ODT disable frequency in MHz (Mega Hz). + When DDR frequency is less then ddr3_odt_dis_freq, + the ODT on the DRAM side and controller side are both disabled. -- rockchip,lpddr3_drv : When dram type is LPDDR3, this parameter define - the dram side driver stength in ohm, default +- rockchip,lpddr3_drv : When the DRAM type is LPDDR3, this parameter defines + the DRAM side driver strength in ohms. Default value is LP3_DS_34ohm. -- rockchip,lpddr3_odt : When dram type is LPDDR3, this parameter define - the dram side ODT stength in ohm, default value +- rockchip,lpddr3_odt : When the DRAM type is LPDDR3, this parameter defines + the DRAM side ODT strength in ohms. Default value is LP3_ODT_240ohm. -- rockchip,phy_lpddr3_ca_drv : When dram type is LPDDR3, this parameter define - the phy side CA line(incluing command line, +- rockchip,phy_lpddr3_ca_drv : When the DRAM type is LPDDR3, this parameter defines + the PHY side CA line (including command line, address line and clock line) driver strength. - default value is PHY_DRV_ODT_40. + Default value is PHY_DRV_ODT_40. -- rockchip,phy_lpddr3_dq_drv : When dram type is LPDDR3, this parameter define - the phy side DQ line(incluing DQS/DQ/DM line) - driver strength. default value is +- rockchip,phy_lpddr3_dq_drv : When the DRAM type is LPDDR3, this parameter defines + the PHY side DQ line (including DQS/DQ/DM line) + driver strength. Default value is PHY_DRV_ODT_40. - rockchip,phy_lpddr3_odt : When dram type is LPDDR3, this parameter define the phy side odt strength, default value is PHY_DRV_ODT_240. -- rockchip,lpddr4_odt_disb_freq : When dram type is LPDDR4, this parameter - defined the odt disable frequency in - MHz (Mega Hz), when ddr frequency less then - ddr3_odt_disb_freq, the odt on dram side and +- rockchip,lpddr4_odt_dis_freq : When the DRAM type is LPDDR4, this parameter + defines the ODT disable frequency in + MHz (Mega Hz). When the DDR frequency is less then + ddr3_odt_dis_freq, the ODT on the DRAM side and controller side are both disabled. -- rockchip,lpddr4_drv : When dram type is LPDDR4, this parameter define - the dram side driver stength in ohm, default +- rockchip,lpddr4_drv : When the DRAM type is LPDDR4, this parameter defines + the DRAM side driver strength in ohms. Default value is LP4_PDDS_60ohm. -- rockchip,lpddr4_dq_odt : When dram type is LPDDR4, this parameter define - the dram side ODT on dqs/dq line stength in ohm, - default value is LP4_DQ_ODT_40ohm. +- rockchip,lpddr4_dq_odt : When the DRAM type is LPDDR4, this parameter defines + the DRAM side ODT on DQS/DQ line strength in ohms. + Default value is LP4_DQ_ODT_40ohm. -- rockchip,lpddr4_ca_odt : When dram type is LPDDR4, this parameter define - the dram side ODT on ca line stength in ohm, - default value is LP4_CA_ODT_40ohm. +- rockchip,lpddr4_ca_odt : When the DRAM type is LPDDR4, this parameter defines + the DRAM side ODT on CA line strength in ohms. + Default value is LP4_CA_ODT_40ohm. -- rockchip,phy_lpddr4_ca_drv : When dram type is LPDDR4, this parameter define - the phy side CA line(incluing command address - line) driver strength. default value is +- rockchip,phy_lpddr4_ca_drv : When the DRAM type is LPDDR4, this parameter defines + the PHY side CA line (including command address + line) driver strength. Default value is PHY_DRV_ODT_40. -- rockchip,phy_lpddr4_ck_cs_drv : When dram type is LPDDR4, this parameter define - the phy side clock line and cs line driver - strength. default value is PHY_DRV_ODT_80. +- rockchip,phy_lpddr4_ck_cs_drv : When the DRAM type is LPDDR4, this parameter defines + the PHY side clock line and CS line driver + strength. Default value is PHY_DRV_ODT_80. -- rockchip,phy_lpddr4_dq_drv : When dram type is LPDDR4, this parameter define - the phy side DQ line(incluing DQS/DQ/DM line) - driver strength. default value is PHY_DRV_ODT_80. +- rockchip,phy_lpddr4_dq_drv : When the DRAM type is LPDDR4, this parameter defines + the PHY side DQ line (including DQS/DQ/DM line) + driver strength. Default value is PHY_DRV_ODT_80. -- rockchip,phy_lpddr4_odt : When dram type is LPDDR4, this parameter define - the phy side odt strength, default value is +- rockchip,phy_lpddr4_odt : When the DRAM type is LPDDR4, this parameter defines + the PHY side ODT strength. Default value is PHY_DRV_ODT_60. Example: |