diff options
Diffstat (limited to 'Documentation/devicetree/bindings/c6x')
| -rw-r--r-- | Documentation/devicetree/bindings/c6x/clocks.txt | 40 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/c6x/dscr.txt | 127 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/c6x/emifa.txt | 62 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/c6x/soc.txt | 28 |
4 files changed, 0 insertions, 257 deletions
diff --git a/Documentation/devicetree/bindings/c6x/clocks.txt b/Documentation/devicetree/bindings/c6x/clocks.txt deleted file mode 100644 index a04f5fd30122..000000000000 --- a/Documentation/devicetree/bindings/c6x/clocks.txt +++ /dev/null @@ -1,40 +0,0 @@ -C6X PLL Clock Controllers -------------------------- - -This is a first-cut support for the SoC clock controllers. This is still -under development and will probably change as the common device tree -clock support is added to the kernel. - -Required properties: - -- compatible: "ti,c64x+pll" - May also have SoC-specific value to support SoC-specific initialization - in the driver. One of: - "ti,c6455-pll" - "ti,c6457-pll" - "ti,c6472-pll" - "ti,c6474-pll" - -- reg: base address and size of register area -- clock-frequency: input clock frequency in hz - - -Optional properties: - -- ti,c64x+pll-bypass-delay: CPU cycles to delay when entering bypass mode - -- ti,c64x+pll-reset-delay: CPU cycles to delay after PLL reset - -- ti,c64x+pll-lock-delay: CPU cycles to delay after PLL frequency change - -Example: - - clock-controller@29a0000 { - compatible = "ti,c6472-pll", "ti,c64x+pll"; - reg = <0x029a0000 0x200>; - clock-frequency = <25000000>; - - ti,c64x+pll-bypass-delay = <200>; - ti,c64x+pll-reset-delay = <12000>; - ti,c64x+pll-lock-delay = <80000>; - }; diff --git a/Documentation/devicetree/bindings/c6x/dscr.txt b/Documentation/devicetree/bindings/c6x/dscr.txt deleted file mode 100644 index 92672235de57..000000000000 --- a/Documentation/devicetree/bindings/c6x/dscr.txt +++ /dev/null @@ -1,127 +0,0 @@ -Device State Configuration Registers ------------------------------------- - -TI C6X SoCs contain a region of miscellaneous registers which provide various -function for SoC control or status. Details vary considerably among from SoC -to SoC with no two being alike. - -In general, the Device State Configuration Registers (DSCR) will provide one or -more configuration registers often protected by a lock register where one or -more key values must be written to a lock register in order to unlock the -configuration register for writes. These configuration register may be used to -enable (and disable in some cases) SoC pin drivers, select peripheral clock -sources (internal or pin), etc. In some cases, a configuration register is -write once or the individual bits are write once. In addition to device config, -the DSCR block may provide registers which are used to reset peripherals, -provide device ID information, provide ethernet MAC addresses, as well as other -miscellaneous functions. - -For device state control (enable/disable), each device control is assigned an -id which is used by individual device drivers to control the state as needed. - -Required properties: - -- compatible: must be "ti,c64x+dscr" -- reg: register area base and size - -Optional properties: - - NOTE: These are optional in that not all SoCs will have all properties. For - SoCs which do support a given property, leaving the property out of the - device tree will result in reduced functionality or possibly driver - failure. - -- ti,dscr-devstat - offset of the devstat register - -- ti,dscr-silicon-rev - offset, start bit, and bitsize of silicon revision field - -- ti,dscr-rmii-resets - offset and bitmask of RMII reset field. May have multiple tuples if more - than one ethernet port is available. - -- ti,dscr-locked-regs - possibly multiple tuples describing registers which are write protected by - a lock register. Each tuple consists of the register offset, lock register - offsset, and the key value used to unlock the register. - -- ti,dscr-kick-regs - offset and key values of two "kick" registers used to write protect other - registers in DSCR. On SoCs using kick registers, the first key must be - written to the first kick register and the second key must be written to - the second register before other registers in the area are write-enabled. - -- ti,dscr-mac-fuse-regs - MAC addresses are contained in two registers. Each element of a MAC address - is contained in a single byte. This property has two tuples. Each tuple has - a register offset and four cells representing bytes in the register from - most significant to least. The value of these four cells is the MAC byte - index (1-6) of the byte within the register. A value of 0 means the byte - is unused in the MAC address. - -- ti,dscr-devstate-ctl-regs - This property describes the bitfields used to control the state of devices. - Each tuple describes a range of identical bitfields used to control one or - more devices (one bitfield per device). The layout of each tuple is: - - start_id num_ids reg enable disable start_bit nbits - - Where: - start_id is device id for the first device control in the range - num_ids is the number of device controls in the range - reg is the offset of the register holding the control bits - enable is the value to enable a device - disable is the value to disable a device (0xffffffff if cannot disable) - start_bit is the bit number of the first bit in the range - nbits is the number of bits per device control - -- ti,dscr-devstate-stat-regs - This property describes the bitfields used to provide device state status - for device states controlled by the DSCR. Each tuple describes a range of - identical bitfields used to provide status for one or more devices (one - bitfield per device). The layout of each tuple is: - - start_id num_ids reg enable disable start_bit nbits - - Where: - start_id is device id for the first device status in the range - num_ids is the number of devices covered by the range - reg is the offset of the register holding the status bits - enable is the value indicating device is enabled - disable is the value indicating device is disabled - start_bit is the bit number of the first bit in the range - nbits is the number of bits per device status - -- ti,dscr-privperm - Offset and default value for register used to set access privilege for - some SoC devices. - - -Example: - - device-state-config-regs@2a80000 { - compatible = "ti,c64x+dscr"; - reg = <0x02a80000 0x41000>; - - ti,dscr-devstat = <0>; - ti,dscr-silicon-rev = <8 28 0xf>; - ti,dscr-rmii-resets = <0x40020 0x00040000>; - - ti,dscr-locked-regs = <0x40008 0x40004 0x0f0a0b00>; - ti,dscr-devstate-ctl-regs = - <0 12 0x40008 1 0 0 2 - 12 1 0x40008 3 0 30 2 - 13 2 0x4002c 1 0xffffffff 0 1>; - ti,dscr-devstate-stat-regs = - <0 10 0x40014 1 0 0 3 - 10 2 0x40018 1 0 0 3>; - - ti,dscr-mac-fuse-regs = <0x700 1 2 3 4 - 0x704 5 6 0 0>; - - ti,dscr-privperm = <0x41c 0xaaaaaaaa>; - - ti,dscr-kick-regs = <0x38 0x83E70B13 - 0x3c 0x95A4F1E0>; - }; diff --git a/Documentation/devicetree/bindings/c6x/emifa.txt b/Documentation/devicetree/bindings/c6x/emifa.txt deleted file mode 100644 index 0ff6e9b9a13f..000000000000 --- a/Documentation/devicetree/bindings/c6x/emifa.txt +++ /dev/null @@ -1,62 +0,0 @@ -External Memory Interface -------------------------- - -The emifa node describes a simple external bus controller found on some C6X -SoCs. This interface provides external busses with a number of chip selects. - -Required properties: - -- compatible: must be "ti,c64x+emifa", "simple-bus" -- reg: register area base and size -- #address-cells: must be 2 (chip-select + offset) -- #size-cells: must be 1 -- ranges: mapping from EMIFA space to parent space - - -Optional properties: - -- ti,dscr-dev-enable: Device ID if EMIF is enabled/disabled from DSCR - -- ti,emifa-burst-priority: - Number of memory transfers after which the EMIF will elevate the priority - of the oldest command in the command FIFO. Setting this field to 255 - disables this feature, thereby allowing old commands to stay in the FIFO - indefinitely. - -- ti,emifa-ce-config: - Configuration values for each of the supported chip selects. - -Example: - - emifa@70000000 { - compatible = "ti,c64x+emifa", "simple-bus"; - #address-cells = <2>; - #size-cells = <1>; - reg = <0x70000000 0x100>; - ranges = <0x2 0x0 0xa0000000 0x00000008 - 0x3 0x0 0xb0000000 0x00400000 - 0x4 0x0 0xc0000000 0x10000000 - 0x5 0x0 0xD0000000 0x10000000>; - - ti,dscr-dev-enable = <13>; - ti,emifa-burst-priority = <255>; - ti,emifa-ce-config = <0x00240120 - 0x00240120 - 0x00240122 - 0x00240122>; - - flash@3,0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "cfi-flash"; - reg = <0x3 0x0 0x400000>; - bank-width = <1>; - device-width = <1>; - partition@0 { - reg = <0x0 0x400000>; - label = "NOR"; - }; - }; - }; - -This shows a flash chip attached to chip select 3. diff --git a/Documentation/devicetree/bindings/c6x/soc.txt b/Documentation/devicetree/bindings/c6x/soc.txt deleted file mode 100644 index b1e4973b5769..000000000000 --- a/Documentation/devicetree/bindings/c6x/soc.txt +++ /dev/null @@ -1,28 +0,0 @@ -C6X System-on-Chip ------------------- - -Required properties: - -- compatible: "simple-bus" -- #address-cells: must be 1 -- #size-cells: must be 1 -- ranges - -Optional properties: - -- model: specific SoC model - -- nodes for IP blocks within SoC - - -Example: - - soc { - compatible = "simple-bus"; - model = "tms320c6455"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - ... - }; |