diff options
Diffstat (limited to 'Documentation/PCI/msi-howto.rst')
| -rw-r--r-- | Documentation/PCI/msi-howto.rst | 287 |
1 files changed, 287 insertions, 0 deletions
diff --git a/Documentation/PCI/msi-howto.rst b/Documentation/PCI/msi-howto.rst new file mode 100644 index 000000000000..994cbb660ade --- /dev/null +++ b/Documentation/PCI/msi-howto.rst @@ -0,0 +1,287 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. include:: <isonum.txt> + +========================== +The MSI Driver Guide HOWTO +========================== + +:Authors: Tom L Nguyen; Martine Silbermann; Matthew Wilcox + +:Copyright: 2003, 2008 Intel Corporation + +About this guide +================ + +This guide describes the basics of Message Signaled Interrupts (MSIs), +the advantages of using MSI over traditional interrupt mechanisms, how +to change your driver to use MSI or MSI-X and some basic diagnostics to +try if a device doesn't support MSIs. + + +What are MSIs? +============== + +A Message Signaled Interrupt is a write from the device to a special +address which causes an interrupt to be received by the CPU. + +The MSI capability was first specified in PCI 2.2 and was later enhanced +in PCI 3.0 to allow each interrupt to be masked individually. The MSI-X +capability was also introduced with PCI 3.0. It supports more interrupts +per device than MSI and allows interrupts to be independently configured. + +Devices may support both MSI and MSI-X, but only one can be enabled at +a time. + + +Why use MSIs? +============= + +There are three reasons why using MSIs can give an advantage over +traditional pin-based interrupts. + +Pin-based PCI interrupts are often shared amongst several devices. +To support this, the kernel must call each interrupt handler associated +with an interrupt, which leads to reduced performance for the system as +a whole. MSIs are never shared, so this problem cannot arise. + +When a device writes data to memory, then raises a pin-based interrupt, +it is possible that the interrupt may arrive before all the data has +arrived in memory (this becomes more likely with devices behind PCI-PCI +bridges). In order to ensure that all the data has arrived in memory, +the interrupt handler must read a register on the device which raised +the interrupt. PCI transaction ordering rules require that all the data +arrive in memory before the value may be returned from the register. +Using MSIs avoids this problem as the interrupt-generating write cannot +pass the data writes, so by the time the interrupt is raised, the driver +knows that all the data has arrived in memory. + +PCI devices can only support a single pin-based interrupt per function. +Often drivers have to query the device to find out what event has +occurred, slowing down interrupt handling for the common case. With +MSIs, a device can support more interrupts, allowing each interrupt +to be specialised to a different purpose. One possible design gives +infrequent conditions (such as errors) their own interrupt which allows +the driver to handle the normal interrupt handling path more efficiently. +Other possible designs include giving one interrupt to each packet queue +in a network card or each port in a storage controller. + + +How to use MSIs +=============== + +PCI devices are initialised to use pin-based interrupts. The device +driver has to set up the device to use MSI or MSI-X. Not all machines +support MSIs correctly, and for those machines, the APIs described below +will simply fail and the device will continue to use pin-based interrupts. + +Include kernel support for MSIs +------------------------------- + +To support MSI or MSI-X, the kernel must be built with the CONFIG_PCI_MSI +option enabled. This option is only available on some architectures, +and it may depend on some other options also being set. For example, +on x86, you must also enable X86_UP_APIC or SMP in order to see the +CONFIG_PCI_MSI option. + +Using MSI +--------- + +Most of the hard work is done for the driver in the PCI layer. The driver +simply has to request that the PCI layer set up the MSI capability for this +device. + +To automatically use MSI or MSI-X interrupt vectors, use the following +function:: + + int pci_alloc_irq_vectors(struct pci_dev *dev, unsigned int min_vecs, + unsigned int max_vecs, unsigned int flags); + +which allocates up to max_vecs interrupt vectors for a PCI device. It +returns the number of vectors allocated or a negative error. If the device +has a requirements for a minimum number of vectors the driver can pass a +min_vecs argument set to this limit, and the PCI core will return -ENOSPC +if it can't meet the minimum number of vectors. + +The flags argument is used to specify which type of interrupt can be used +by the device and the driver (PCI_IRQ_LEGACY, PCI_IRQ_MSI, PCI_IRQ_MSIX). +A convenient short-hand (PCI_IRQ_ALL_TYPES) is also available to ask for +any possible kind of interrupt. If the PCI_IRQ_AFFINITY flag is set, +pci_alloc_irq_vectors() will spread the interrupts around the available CPUs. + +To get the Linux IRQ numbers passed to request_irq() and free_irq() and the +vectors, use the following function:: + + int pci_irq_vector(struct pci_dev *dev, unsigned int nr); + +Any allocated resources should be freed before removing the device using +the following function:: + + void pci_free_irq_vectors(struct pci_dev *dev); + +If a device supports both MSI-X and MSI capabilities, this API will use the +MSI-X facilities in preference to the MSI facilities. MSI-X supports any +number of interrupts between 1 and 2048. In contrast, MSI is restricted to +a maximum of 32 interrupts (and must be a power of two). In addition, the +MSI interrupt vectors must be allocated consecutively, so the system might +not be able to allocate as many vectors for MSI as it could for MSI-X. On +some platforms, MSI interrupts must all be targeted at the same set of CPUs +whereas MSI-X interrupts can all be targeted at different CPUs. + +If a device supports neither MSI-X or MSI it will fall back to a single +legacy IRQ vector. + +The typical usage of MSI or MSI-X interrupts is to allocate as many vectors +as possible, likely up to the limit supported by the device. If nvec is +larger than the number supported by the device it will automatically be +capped to the supported limit, so there is no need to query the number of +vectors supported beforehand:: + + nvec = pci_alloc_irq_vectors(pdev, 1, nvec, PCI_IRQ_ALL_TYPES) + if (nvec < 0) + goto out_err; + +If a driver is unable or unwilling to deal with a variable number of MSI +interrupts it can request a particular number of interrupts by passing that +number to pci_alloc_irq_vectors() function as both 'min_vecs' and +'max_vecs' parameters:: + + ret = pci_alloc_irq_vectors(pdev, nvec, nvec, PCI_IRQ_ALL_TYPES); + if (ret < 0) + goto out_err; + +The most notorious example of the request type described above is enabling +the single MSI mode for a device. It could be done by passing two 1s as +'min_vecs' and 'max_vecs':: + + ret = pci_alloc_irq_vectors(pdev, 1, 1, PCI_IRQ_ALL_TYPES); + if (ret < 0) + goto out_err; + +Some devices might not support using legacy line interrupts, in which case +the driver can specify that only MSI or MSI-X is acceptable:: + + nvec = pci_alloc_irq_vectors(pdev, 1, nvec, PCI_IRQ_MSI | PCI_IRQ_MSIX); + if (nvec < 0) + goto out_err; + +Legacy APIs +----------- + +The following old APIs to enable and disable MSI or MSI-X interrupts should +not be used in new code:: + + pci_enable_msi() /* deprecated */ + pci_disable_msi() /* deprecated */ + pci_enable_msix_range() /* deprecated */ + pci_enable_msix_exact() /* deprecated */ + pci_disable_msix() /* deprecated */ + +Additionally there are APIs to provide the number of supported MSI or MSI-X +vectors: pci_msi_vec_count() and pci_msix_vec_count(). In general these +should be avoided in favor of letting pci_alloc_irq_vectors() cap the +number of vectors. If you have a legitimate special use case for the count +of vectors we might have to revisit that decision and add a +pci_nr_irq_vectors() helper that handles MSI and MSI-X transparently. + +Considerations when using MSIs +------------------------------ + +Spinlocks +~~~~~~~~~ + +Most device drivers have a per-device spinlock which is taken in the +interrupt handler. With pin-based interrupts or a single MSI, it is not +necessary to disable interrupts (Linux guarantees the same interrupt will +not be re-entered). If a device uses multiple interrupts, the driver +must disable interrupts while the lock is held. If the device sends +a different interrupt, the driver will deadlock trying to recursively +acquire the spinlock. Such deadlocks can be avoided by using +spin_lock_irqsave() or spin_lock_irq() which disable local interrupts +and acquire the lock (see Documentation/kernel-hacking/locking.rst). + +How to tell whether MSI/MSI-X is enabled on a device +---------------------------------------------------- + +Using 'lspci -v' (as root) may show some devices with "MSI", "Message +Signalled Interrupts" or "MSI-X" capabilities. Each of these capabilities +has an 'Enable' flag which is followed with either "+" (enabled) +or "-" (disabled). + + +MSI quirks +========== + +Several PCI chipsets or devices are known not to support MSIs. +The PCI stack provides three ways to disable MSIs: + +1. globally +2. on all devices behind a specific bridge +3. on a single device + +Disabling MSIs globally +----------------------- + +Some host chipsets simply don't support MSIs properly. If we're +lucky, the manufacturer knows this and has indicated it in the ACPI +FADT table. In this case, Linux automatically disables MSIs. +Some boards don't include this information in the table and so we have +to detect them ourselves. The complete list of these is found near the +quirk_disable_all_msi() function in drivers/pci/quirks.c. + +If you have a board which has problems with MSIs, you can pass pci=nomsi +on the kernel command line to disable MSIs on all devices. It would be +in your best interests to report the problem to linux-pci@vger.kernel.org +including a full 'lspci -v' so we can add the quirks to the kernel. + +Disabling MSIs below a bridge +----------------------------- + +Some PCI bridges are not able to route MSIs between busses properly. +In this case, MSIs must be disabled on all devices behind the bridge. + +Some bridges allow you to enable MSIs by changing some bits in their +PCI configuration space (especially the Hypertransport chipsets such +as the nVidia nForce and Serverworks HT2000). As with host chipsets, +Linux mostly knows about them and automatically enables MSIs if it can. +If you have a bridge unknown to Linux, you can enable +MSIs in configuration space using whatever method you know works, then +enable MSIs on that bridge by doing:: + + echo 1 > /sys/bus/pci/devices/$bridge/msi_bus + +where $bridge is the PCI address of the bridge you've enabled (eg +0000:00:0e.0). + +To disable MSIs, echo 0 instead of 1. Changing this value should be +done with caution as it could break interrupt handling for all devices +below this bridge. + +Again, please notify linux-pci@vger.kernel.org of any bridges that need +special handling. + +Disabling MSIs on a single device +--------------------------------- + +Some devices are known to have faulty MSI implementations. Usually this +is handled in the individual device driver, but occasionally it's necessary +to handle this with a quirk. Some drivers have an option to disable use +of MSI. While this is a convenient workaround for the driver author, +it is not good practice, and should not be emulated. + +Finding why MSIs are disabled on a device +----------------------------------------- + +From the above three sections, you can see that there are many reasons +why MSIs may not be enabled for a given device. Your first step should +be to examine your dmesg carefully to determine whether MSIs are enabled +for your machine. You should also check your .config to be sure you +have enabled CONFIG_PCI_MSI. + +Then, 'lspci -t' gives the list of bridges above a device. Reading +`/sys/bus/pci/devices/*/msi_bus` will tell you whether MSIs are enabled (1) +or disabled (0). If 0 is found in any of the msi_bus files belonging +to bridges between the PCI root and the device, MSIs are disabled. + +It is also worth checking the device driver to see whether it supports MSIs. +For example, it may contain calls to pci_irq_alloc_vectors() with the +PCI_IRQ_MSI or PCI_IRQ_MSIX flags. |