diff options
| -rw-r--r-- | arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 34 | ||||
| -rw-r--r-- | arch/arm64/boot/dts/qcom/msm8916.dtsi | 62 |
2 files changed, 47 insertions, 49 deletions
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi index a17f5b9a5de6..f611647e9880 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi @@ -215,22 +215,16 @@ usb@78d9000 { extcon = <&usb_id>, <&usb_id>; status = "okay"; - }; - - ehci@78d9000 { - status = "okay"; - }; - - phy@78d9000 { - v1p8-supply = <&pm8916_l7>; - v3p3-supply = <&pm8916_l13>; - vddcx-supply = <&pm8916_s1>; - extcon = <&usb_id>, <&usb_id>; - dr_mode = "otg"; - status = "okay"; - switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&usb_sw_sel_pm>; + adp-disable; + hnp-disable; + srp-disable; + ulpi { + phy { + v1p8-supply = <&pm8916_l7>; + v3p3-supply = <&pm8916_l13>; + extcon = <&usb_id>; + }; + }; }; lpass@07708000 { @@ -348,6 +342,14 @@ pinctrl-0 = <&usb_id_default>; }; + usb-switch { + compatible = "toshiba,tc7usb40mu"; + switch-gpios = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>; + extcon = <&usb_id>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_sw_sel_pm>; + }; + hdmi-out { compatible = "hdmi-connector"; type = "a"; diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi index ab3093995ded..c963ef2ec5f5 100644 --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi @@ -546,44 +546,40 @@ status = "disabled"; }; - usb_dev: usb@78d9000 { + otg: usb@78d9000 { compatible = "qcom,ci-hdrc"; - reg = <0x78d9000 0x400>; - dr_mode = "peripheral"; - interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; - usb-phy = <&usb_otg>; - status = "disabled"; - }; - - usb_host: ehci@78d9000 { - compatible = "qcom,ehci-host"; - reg = <0x78d9000 0x400>; - interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; - usb-phy = <&usb_otg>; - status = "disabled"; - }; - - usb_otg: phy@78d9000 { - compatible = "qcom,usb-otg-snps"; - reg = <0x78d9000 0x400>; + reg = <0x78d9000 0x200>, + <0x78d9200 0x200>; interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; - - qcom,vdd-levels = <500000 1000000 1320000>; - qcom,phy-init-sequence = <0x44 0x6B 0x24 0x13>; - dr_mode = "peripheral"; - qcom,otg-control = <2>; // PMIC - qcom,manual-pullup; - clocks = <&gcc GCC_USB_HS_AHB_CLK>, - <&gcc GCC_USB_HS_SYSTEM_CLK>, - <&gcc GCC_USB2A_PHY_SLEEP_CLK>; - clock-names = "iface", "core", "sleep"; - - resets = <&gcc GCC_USB2A_PHY_BCR>, - <&gcc GCC_USB_HS_BCR>; - reset-names = "phy", "link"; + <&gcc GCC_USB_HS_SYSTEM_CLK>; + clock-names = "iface", "core"; + assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>; + assigned-clock-rates = <80000000>; + resets = <&gcc GCC_USB_HS_BCR>; + reset-names = "core"; + phy_type = "ulpi"; + dr_mode = "otg"; + ahb-burst-config = <0>; + phy-names = "usb-phy"; + phys = <&usb_hs_phy>; status = "disabled"; + #reset-cells = <1>; + + ulpi { + usb_hs_phy: phy { + compatible = "qcom,usb-hs-phy-msm8916", + "qcom,usb-hs-phy"; + #phy-cells = <0>; + clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>; + clock-names = "ref", "sleep"; + resets = <&gcc GCC_USB2A_PHY_BCR>, <&otg 0>; + reset-names = "phy", "por"; + qcom,init-seq = /bits/ 8 <0x0 0x44 + 0x1 0x6b 0x2 0x24 0x3 0x13>; + }; + }; }; intc: interrupt-controller@b000000 { |