summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--arch/arm/mach-s3c2410/include/mach/spi.h2
-rw-r--r--drivers/spi/Kconfig28
-rw-r--r--drivers/spi/Makefile10
-rw-r--r--drivers/spi/atmel_spi.c6
-rw-r--r--drivers/spi/dw_spi.c944
-rw-r--r--drivers/spi/dw_spi_pci.c169
-rw-r--r--drivers/spi/spi_bfin5xx.c2
-rw-r--r--drivers/spi/spi_mpc8xxx.c2
-rw-r--r--drivers/spi/spi_s3c24xx.c244
-rw-r--r--drivers/spi/spi_s3c24xx_fiq.S116
-rw-r--r--drivers/spi/spi_s3c24xx_fiq.h26
-rw-r--r--drivers/spi/spi_s3c64xx.c1196
-rw-r--r--drivers/spi/spi_sh_sci.c2
-rw-r--r--drivers/spi/spi_txx9.c6
-rw-r--r--drivers/spi/spidev.c18
-rw-r--r--include/linux/spi/dw_spi.h212
16 files changed, 2950 insertions, 33 deletions
diff --git a/arch/arm/mach-s3c2410/include/mach/spi.h b/arch/arm/mach-s3c2410/include/mach/spi.h
index 193b39d654ed..4d9588373aa5 100644
--- a/arch/arm/mach-s3c2410/include/mach/spi.h
+++ b/arch/arm/mach-s3c2410/include/mach/spi.h
@@ -18,6 +18,8 @@ struct s3c2410_spi_info {
unsigned int num_cs; /* total chipselects */
int bus_num; /* bus number to use. */
+ unsigned int use_fiq:1; /* use fiq */
+
void (*gpio_setup)(struct s3c2410_spi_info *spi, int enable);
void (*set_cs)(struct s3c2410_spi_info *spi, int cs, int pol);
};
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 2d9d70359360..f55eb0107336 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -216,6 +216,17 @@ config SPI_S3C24XX
help
SPI driver for Samsung S3C24XX series ARM SoCs
+config SPI_S3C24XX_FIQ
+ bool "S3C24XX driver with FIQ pseudo-DMA"
+ depends on SPI_S3C24XX
+ select FIQ
+ help
+ Enable FIQ support for the S3C24XX SPI driver to provide pseudo
+ DMA by using the fast-interrupt request framework, This allows
+ the driver to get DMA-like performance when there are either
+ no free DMA channels, or when doing transfers that required both
+ TX and RX data paths.
+
config SPI_S3C24XX_GPIO
tristate "Samsung S3C24XX series SPI by GPIO"
depends on ARCH_S3C2410 && EXPERIMENTAL
@@ -226,6 +237,13 @@ config SPI_S3C24XX_GPIO
the inbuilt hardware cannot provide the transfer mode, or
where the board is using non hardware connected pins.
+config SPI_S3C64XX
+ tristate "Samsung S3C64XX series type SPI"
+ depends on ARCH_S3C64XX && EXPERIMENTAL
+ select S3C64XX_DMA
+ help
+ SPI driver for Samsung S3C64XX and newer SoCs.
+
config SPI_SH_MSIOF
tristate "SuperH MSIOF SPI controller"
depends on SUPERH && HAVE_CLK
@@ -289,6 +307,16 @@ config SPI_NUC900
# Add new SPI master controllers in alphabetical order above this line
#
+config SPI_DESIGNWARE
+ bool "DesignWare SPI controller core support"
+ depends on SPI_MASTER
+ help
+ general driver for SPI controller core from DesignWare
+
+config SPI_DW_PCI
+ tristate "PCI interface driver for DW SPI core"
+ depends on SPI_DESIGNWARE && PCI
+
#
# There are lots of SPI device types, with sensors and memory
# being probably the most widely used ones.
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index ed8c1675b52f..f3d2810ba11c 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -16,6 +16,8 @@ obj-$(CONFIG_SPI_BFIN) += spi_bfin5xx.o
obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o
obj-$(CONFIG_SPI_AU1550) += au1550_spi.o
obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o
+obj-$(CONFIG_SPI_DESIGNWARE) += dw_spi.o
+obj-$(CONFIG_SPI_DW_PCI) += dw_spi_pci.o
obj-$(CONFIG_SPI_GPIO) += spi_gpio.o
obj-$(CONFIG_SPI_IMX) += spi_imx.o
obj-$(CONFIG_SPI_LM70_LLP) += spi_lm70llp.o
@@ -30,7 +32,8 @@ obj-$(CONFIG_SPI_MPC52xx) += mpc52xx_spi.o
obj-$(CONFIG_SPI_MPC8xxx) += spi_mpc8xxx.o
obj-$(CONFIG_SPI_PPC4xx) += spi_ppc4xx.o
obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o
-obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx.o
+obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx_hw.o
+obj-$(CONFIG_SPI_S3C64XX) += spi_s3c64xx.o
obj-$(CONFIG_SPI_TXX9) += spi_txx9.o
obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o
obj-$(CONFIG_SPI_XILINX_OF) += xilinx_spi_of.o
@@ -39,6 +42,11 @@ obj-$(CONFIG_SPI_SH_SCI) += spi_sh_sci.o
obj-$(CONFIG_SPI_SH_MSIOF) += spi_sh_msiof.o
obj-$(CONFIG_SPI_STMP3XXX) += spi_stmp.o
obj-$(CONFIG_SPI_NUC900) += spi_nuc900.o
+
+# special build for s3c24xx spi driver with fiq support
+spi_s3c24xx_hw-y := spi_s3c24xx.o
+spi_s3c24xx_hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi_s3c24xx_fiq.o
+
# ... add above this line ...
# SPI protocol drivers (device/link on bus)
diff --git a/drivers/spi/atmel_spi.c b/drivers/spi/atmel_spi.c
index f5b3fdbb1e27..d21c24eaf0a9 100644
--- a/drivers/spi/atmel_spi.c
+++ b/drivers/spi/atmel_spi.c
@@ -189,14 +189,14 @@ static void atmel_spi_next_xfer_data(struct spi_master *master,
/* use scratch buffer only when rx or tx data is unspecified */
if (xfer->rx_buf)
- *rx_dma = xfer->rx_dma + xfer->len - len;
+ *rx_dma = xfer->rx_dma + xfer->len - *plen;
else {
*rx_dma = as->buffer_dma;
if (len > BUFFER_SIZE)
len = BUFFER_SIZE;
}
if (xfer->tx_buf)
- *tx_dma = xfer->tx_dma + xfer->len - len;
+ *tx_dma = xfer->tx_dma + xfer->len - *plen;
else {
*tx_dma = as->buffer_dma;
if (len > BUFFER_SIZE)
@@ -788,7 +788,7 @@ static int __init atmel_spi_probe(struct platform_device *pdev)
spin_lock_init(&as->lock);
INIT_LIST_HEAD(&as->queue);
as->pdev = pdev;
- as->regs = ioremap(regs->start, (regs->end - regs->start) + 1);
+ as->regs = ioremap(regs->start, resource_size(regs));
if (!as->regs)
goto out_free_buffer;
as->irq = irq;
diff --git a/drivers/spi/dw_spi.c b/drivers/spi/dw_spi.c
new file mode 100644
index 000000000000..31620fae77be
--- /dev/null
+++ b/drivers/spi/dw_spi.c
@@ -0,0 +1,944 @@
+/*
+ * dw_spi.c - Designware SPI core controller driver (refer pxa2xx_spi.c)
+ *
+ * Copyright (c) 2009, Intel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/interrupt.h>
+#include <linux/highmem.h>
+#include <linux/delay.h>
+
+#include <linux/spi/dw_spi.h>
+#include <linux/spi/spi.h>
+
+#ifdef CONFIG_DEBUG_FS
+#include <linux/debugfs.h>
+#endif
+
+#define START_STATE ((void *)0)
+#define RUNNING_STATE ((void *)1)
+#define DONE_STATE ((void *)2)
+#define ERROR_STATE ((void *)-1)
+
+#define QUEUE_RUNNING 0
+#define QUEUE_STOPPED 1
+
+#define MRST_SPI_DEASSERT 0
+#define MRST_SPI_ASSERT 1
+
+/* Slave spi_dev related */
+struct chip_data {
+ u16 cr0;
+ u8 cs; /* chip select pin */
+ u8 n_bytes; /* current is a 1/2/4 byte op */
+ u8 tmode; /* TR/TO/RO/EEPROM */
+ u8 type; /* SPI/SSP/MicroWire */
+
+ u8 poll_mode; /* 1 means use poll mode */
+
+ u32 dma_width;
+ u32 rx_threshold;
+ u32 tx_threshold;
+ u8 enable_dma;
+ u8 bits_per_word;
+ u16 clk_div; /* baud rate divider */
+ u32 speed_hz; /* baud rate */
+ int (*write)(struct dw_spi *dws);
+ int (*read)(struct dw_spi *dws);
+ void (*cs_control)(u32 command);
+};
+
+#ifdef CONFIG_DEBUG_FS
+static int spi_show_regs_open(struct inode *inode, struct file *file)
+{
+ file->private_data = inode->i_private;
+ return 0;
+}
+
+#define SPI_REGS_BUFSIZE 1024
+static ssize_t spi_show_regs(struct file *file, char __user *user_buf,
+ size_t count, loff_t *ppos)
+{
+ struct dw_spi *dws;
+ char *buf;
+ u32 len = 0;
+ ssize_t ret;
+
+ dws = file->private_data;
+
+ buf = kzalloc(SPI_REGS_BUFSIZE, GFP_KERNEL);
+ if (!buf)
+ return 0;
+
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "MRST SPI0 registers:\n");
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "=================================\n");
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "CTRL0: \t\t0x%08x\n", dw_readl(dws, ctrl0));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "CTRL1: \t\t0x%08x\n", dw_readl(dws, ctrl1));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "SSIENR: \t0x%08x\n", dw_readl(dws, ssienr));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "SER: \t\t0x%08x\n", dw_readl(dws, ser));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "BAUDR: \t\t0x%08x\n", dw_readl(dws, baudr));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "TXFTLR: \t0x%08x\n", dw_readl(dws, txfltr));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "RXFTLR: \t0x%08x\n", dw_readl(dws, rxfltr));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "TXFLR: \t\t0x%08x\n", dw_readl(dws, txflr));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "RXFLR: \t\t0x%08x\n", dw_readl(dws, rxflr));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "SR: \t\t0x%08x\n", dw_readl(dws, sr));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "IMR: \t\t0x%08x\n", dw_readl(dws, imr));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "ISR: \t\t0x%08x\n", dw_readl(dws, isr));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "DMACR: \t\t0x%08x\n", dw_readl(dws, dmacr));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "DMATDLR: \t0x%08x\n", dw_readl(dws, dmatdlr));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "DMARDLR: \t0x%08x\n", dw_readl(dws, dmardlr));
+ len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
+ "=================================\n");
+
+ ret = simple_read_from_buffer(user_buf, count, ppos, buf, len);
+ kfree(buf);
+ return ret;
+}
+
+static const struct file_operations mrst_spi_regs_ops = {
+ .owner = THIS_MODULE,
+ .open = spi_show_regs_open,
+ .read = spi_show_regs,
+};
+
+static int mrst_spi_debugfs_init(struct dw_spi *dws)
+{
+ dws->debugfs = debugfs_create_dir("mrst_spi", NULL);
+ if (!dws->debugfs)
+ return -ENOMEM;
+
+ debugfs_create_file("registers", S_IFREG | S_IRUGO,
+ dws->debugfs, (void *)dws, &mrst_spi_regs_ops);
+ return 0;
+}
+
+static void mrst_spi_debugfs_remove(struct dw_spi *dws)
+{
+ if (dws->debugfs)
+ debugfs_remove_recursive(dws->debugfs);
+}
+
+#else
+static inline int mrst_spi_debugfs_init(struct dw_spi *dws)
+{
+}
+
+static inline void mrst_spi_debugfs_remove(struct dw_spi *dws)
+{
+}
+#endif /* CONFIG_DEBUG_FS */
+
+static void wait_till_not_busy(struct dw_spi *dws)
+{
+ unsigned long end = jiffies + usecs_to_jiffies(1000);
+
+ while (time_before(jiffies, end)) {
+ if (!(dw_readw(dws, sr) & SR_BUSY))
+ return;
+ }
+ dev_err(&dws->master->dev,
+ "DW SPI: Stutus keeps busy for 1000us after a read/write!\n");
+}
+
+static void flush(struct dw_spi *dws)
+{
+ while (dw_readw(dws, sr) & SR_RF_NOT_EMPT)
+ dw_readw(dws, dr);
+
+ wait_till_not_busy(dws);
+}
+
+static void null_cs_control(u32 command)
+{
+}
+
+static int null_writer(struct dw_spi *dws)
+{
+ u8 n_bytes = dws->n_bytes;
+
+ if (!(dw_readw(dws, sr) & SR_TF_NOT_FULL)
+ || (dws->tx == dws->tx_end))
+ return 0;
+ dw_writew(dws, dr, 0);
+ dws->tx += n_bytes;
+
+ wait_till_not_busy(dws);
+ return 1;
+}
+
+static int null_reader(struct dw_spi *dws)
+{
+ u8 n_bytes = dws->n_bytes;
+
+ while ((dw_readw(dws, sr) & SR_RF_NOT_EMPT)
+ && (dws->rx < dws->rx_end)) {
+ dw_readw(dws, dr);
+ dws->rx += n_bytes;
+ }
+ wait_till_not_busy(dws);
+ return dws->rx == dws->rx_end;
+}
+
+static int u8_writer(struct dw_spi *dws)
+{
+ if (!(dw_readw(dws, sr) & SR_TF_NOT_FULL)
+ || (dws->tx == dws->tx_end))
+ return 0;
+
+ dw_writew(dws, dr, *(u8 *)(dws->tx));
+ ++dws->tx;
+
+ wait_till_not_busy(dws);
+ return 1;
+}
+
+static int u8_reader(struct dw_spi *dws)
+{
+ while ((dw_readw(dws, sr) & SR_RF_NOT_EMPT)
+ && (dws->rx < dws->rx_end)) {
+ *(u8 *)(dws->rx) = dw_readw(dws, dr);
+ ++dws->rx;
+ }
+
+ wait_till_not_busy(dws);
+ return dws->rx == dws->rx_end;
+}
+
+static int u16_writer(struct dw_spi *dws)
+{
+ if (!(dw_readw(dws, sr) & SR_TF_NOT_FULL)
+ || (dws->tx == dws->tx_end))
+ return 0;
+
+ dw_writew(dws, dr, *(u16 *)(dws->tx));
+ dws->tx += 2;
+
+ wait_till_not_busy(dws);
+ return 1;
+}
+
+static int u16_reader(struct dw_spi *dws)
+{
+ u16 temp;
+
+ while ((dw_readw(dws, sr) & SR_RF_NOT_EMPT)
+ && (dws->rx < dws->rx_end)) {
+ temp = dw_readw(dws, dr);
+ *(u16 *)(dws->rx) = temp;
+ dws->rx += 2;
+ }
+
+ wait_till_not_busy(dws);
+ return dws->rx == dws->rx_end;
+}
+
+static void *next_transfer(struct dw_spi *dws)
+{
+ struct spi_message *msg = dws->cur_msg;
+ struct spi_transfer *trans = dws->cur_transfer;
+
+ /* Move to next transfer */
+ if (trans->transfer_list.next != &msg->transfers) {
+ dws->cur_transfer =
+ list_entry(trans->transfer_list.next,
+ struct spi_transfer,
+ transfer_list);
+ return RUNNING_STATE;
+ } else
+ return DONE_STATE;
+}
+
+/*
+ * Note: first step is the protocol driver prepares
+ * a dma-capable memory, and this func just need translate
+ * the virt addr to physical
+ */
+static int map_dma_buffers(struct dw_spi *dws)
+{
+ if (!dws->cur_msg->is_dma_mapped || !dws->dma_inited
+ || !dws->cur_chip->enable_dma)
+ return 0;
+
+ if (dws->cur_transfer->tx_dma)
+ dws->tx_dma = dws->cur_transfer->tx_dma;
+
+ if (dws->cur_transfer->rx_dma)
+ dws->rx_dma = dws->cur_transfer->rx_dma;
+
+ return 1;
+}
+
+/* Caller already set message->status; dma and pio irqs are blocked */
+static void giveback(struct dw_spi *dws)
+{
+ struct spi_transfer *last_transfer;
+ unsigned long flags;
+ struct spi_message *msg;
+
+ spin_lock_irqsave(&dws->lock, flags);
+ msg = dws->cur_msg;
+ dws->cur_msg = NULL;
+ dws->cur_transfer = NULL;
+ dws->prev_chip = dws->cur_chip;
+ dws->cur_chip = NULL;
+ dws->dma_mapped = 0;
+ queue_work(dws->workqueue, &dws->pump_messages);
+ spin_unlock_irqrestore(&dws->lock, flags);
+
+ last_transfer = list_entry(msg->transfers.prev,
+ struct spi_transfer,
+ transfer_list);
+
+ if (!last_transfer->cs_change)
+ dws->cs_control(MRST_SPI_DEASSERT);
+
+ msg->state = NULL;
+ if (msg->complete)
+ msg->complete(msg->context);
+}
+
+static void int_error_stop(struct dw_spi *dws, const char *msg)
+{
+ /* Stop and reset hw */
+ flush(dws);
+ spi_enable_chip(dws, 0);
+
+ dev_err(&dws->master->dev, "%s\n", msg);
+ dws->cur_msg->state = ERROR_STATE;
+ tasklet_schedule(&dws->pump_transfers);
+}
+
+static void transfer_complete(struct dw_spi *dws)
+{
+ /* Update total byte transfered return count actual bytes read */
+ dws->cur_msg->actual_length += dws->len;
+
+ /* Move to next transfer */
+ dws->cur_msg->state = next_transfer(dws);
+
+ /* Handle end of message */
+ if (dws->cur_msg->state == DONE_STATE) {
+ dws->cur_msg->status = 0;
+ giveback(dws);
+ } else
+ tasklet_schedule(&dws->pump_transfers);
+}
+
+static irqreturn_t interrupt_transfer(struct dw_spi *dws)
+{
+ u16 irq_status, irq_mask = 0x3f;
+
+ irq_status = dw_readw(dws, isr) & irq_mask;
+ /* Error handling */
+ if (irq_status & (SPI_INT_TXOI | SPI_INT_RXOI | SPI_INT_RXUI)) {
+ dw_readw(dws, txoicr);
+ dw_readw(dws, rxoicr);
+ dw_readw(dws, rxuicr);
+ int_error_stop(dws, "interrupt_transfer: fifo overrun");
+ return IRQ_HANDLED;
+ }
+
+ /* INT comes from tx */
+ if (dws->tx && (irq_status & SPI_INT_TXEI)) {
+ while (dws->tx < dws->tx_end)
+ dws->write(dws);
+
+ if (dws->tx == dws->tx_end) {
+ spi_mask_intr(dws, SPI_INT_TXEI);
+ transfer_complete(dws);
+ }
+ }
+
+ /* INT comes from rx */
+ if (dws->rx && (irq_status & SPI_INT_RXFI)) {
+ if (dws->read(dws))
+ transfer_complete(dws);
+ }
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t dw_spi_irq(int irq, void *dev_id)
+{
+ struct dw_spi *dws = dev_id;
+
+ if (!dws->cur_msg) {
+ spi_mask_intr(dws, SPI_INT_TXEI);
+ /* Never fail */
+ return IRQ_HANDLED;
+ }
+
+ return dws->transfer_handler(dws);
+}
+
+/* Must be called inside pump_transfers() */
+static void poll_transfer(struct dw_spi *dws)
+{
+ if (dws->tx) {
+ while (dws->write(dws))
+ dws->read(dws);
+ }
+
+ dws->read(dws);
+ transfer_complete(dws);
+}
+
+static void dma_transfer(struct dw_spi *dws, int cs_change)
+{
+}
+
+static void pump_transfers(unsigned long data)
+{
+ struct dw_spi *dws = (struct dw_spi *)data;
+ struct spi_message *message = NULL;
+ struct spi_transfer *transfer = NULL;
+ struct spi_transfer *previous = NULL;
+ struct spi_device *spi = NULL;
+ struct chip_data *chip = NULL;
+ u8 bits = 0;
+ u8 imask = 0;
+ u8 cs_change = 0;
+ u16 clk_div = 0;
+ u32 speed = 0;
+ u32 cr0 = 0;
+
+ /* Get current state information */
+ message = dws->cur_msg;
+ transfer = dws->cur_transfer;
+ chip = dws->cur_chip;
+ spi = message->spi;
+
+ if (message->state == ERROR_STATE) {
+ message->status = -EIO;
+ goto early_exit;
+ }
+
+ /* Handle end of message */
+ if (message->state == DONE_STATE) {
+ message->status = 0;
+ goto early_exit;
+ }
+
+ /* Delay if requested at end of transfer*/
+ if (message->state == RUNNING_STATE) {
+ previous = list_entry(transfer->transfer_list.prev,
+ struct spi_transfer,
+ transfer_list);
+ if (previous->delay_usecs)
+ udelay(previous->delay_usecs);
+ }
+
+ dws->n_bytes = chip->n_bytes;
+ dws->dma_width = chip->dma_width;
+ dws->cs_control = chip->cs_control;
+
+ dws->rx_dma = transfer->rx_dma;
+ dws->tx_dma = transfer->tx_dma;
+ dws->tx = (void *)transfer->tx_buf;
+ dws->tx_end = dws->tx + transfer->len;
+ dws->rx = transfer->rx_buf;
+ dws->rx_end = dws->rx + transfer->len;
+ dws->write = dws->tx ? chip->write : null_writer;
+ dws->read = dws->rx ? chip->read : null_reader;
+ dws->cs_change = transfer->cs_change;
+ dws->len = dws->cur_transfer->len;
+ if (chip != dws->prev_chip)
+ cs_change = 1;
+
+ cr0 = chip->cr0;
+
+ /* Handle per transfer options for bpw and speed */
+ if (transfer->speed_hz) {
+ speed = chip->speed_hz;
+
+ if (transfer->speed_hz != speed) {
+ speed = transfer->speed_hz;
+ if (speed > dws->max_freq) {
+ printk(KERN_ERR "MRST SPI0: unsupported"
+ "freq: %dHz\n", speed);
+ message->status = -EIO;
+ goto early_exit;
+ }
+
+ /* clk_div doesn't support odd number */
+ clk_div = dws->max_freq / speed;
+ clk_div = (clk_div >> 1) << 1;
+
+ chip->speed_hz = speed;
+ chip->clk_div = clk_div;
+ }
+ }
+ if (transfer->bits_per_word) {
+ bits = transfer->bits_per_word;
+
+ switch (bits) {
+ case 8:
+ dws->n_bytes = 1;
+ dws->dma_width = 1;
+ dws->read = (dws->read != null_reader) ?
+ u8_reader : null_reader;
+ dws->write = (dws->write != null_writer) ?
+ u8_writer : null_writer;
+ break;
+ case 16:
+ dws->n_bytes = 2;
+ dws->dma_width = 2;
+ dws->read = (dws->read != null_reader) ?
+ u16_reader : null_reader;
+ dws->write = (dws->write != null_writer) ?
+ u16_writer : null_writer;
+ break;
+ default:
+ printk(KERN_ERR "MRST SPI0: unsupported bits:"
+ "%db\n", bits);
+ message->status = -EIO;
+ goto early_exit;
+ }
+
+ cr0 = (bits - 1)
+ | (chip->type << SPI_FRF_OFFSET)
+ | (spi->mode << SPI_MODE_OFFSET)
+ | (chip->tmode << SPI_TMOD_OFFSET);
+ }
+ message->state = RUNNING_STATE;
+
+ /* Check if current transfer is a DMA transaction */
+ dws->dma_mapped = map_dma_buffers(dws);
+
+ if (!dws->dma_mapped && !chip->poll_mode) {
+ if (dws->rx)
+ imask |= SPI_INT_RXFI;
+ if (dws->tx)
+ imask |= SPI_INT_TXEI;
+ dws->transfer_handler = interrupt_transfer;
+ }
+
+ /*
+ * Reprogram registers only if
+ * 1. chip select changes
+ * 2. clk_div is changed
+ * 3. control value changes
+ */
+ if (dw_readw(dws, ctrl0) != cr0 || cs_change || clk_div) {
+ spi_enable_chip(dws, 0);
+
+ if (dw_readw(dws, ctrl0) != cr0)
+ dw_writew(dws, ctrl0, cr0);
+
+ /* Set the interrupt mask, for poll mode just diable all int */
+ spi_mask_intr(dws, 0xff);
+ if (!chip->poll_mode)
+ spi_umask_intr(dws, imask);
+
+ spi_set_clk(dws, clk_div ? clk_div : chip->clk_div);
+ spi_chip_sel(dws, spi->chip_select);
+ spi_enable_chip(dws, 1);
+
+ if (cs_change)
+ dws->prev_chip = chip;
+ }
+
+ if (dws->dma_mapped)
+ dma_transfer(dws, cs_change);
+
+ if (chip->poll_mode)
+ poll_transfer(dws);
+
+ return;
+
+early_exit:
+ giveback(dws);
+ return;
+}
+
+static void pump_messages(struct work_struct *work)
+{
+ struct dw_spi *dws =
+ container_of(work, struct dw_spi, pump_messages);
+ unsigned long flags;
+
+ /* Lock queue and check for queue work */
+ spin_lock_irqsave(&dws->lock, flags);
+ if (list_empty(&dws->queue) || dws->run == QUEUE_STOPPED) {
+ dws->busy = 0;
+ spin_unlock_irqrestore(&dws->lock, flags);
+ return;
+ }
+
+ /* Make sure we are not already running a message */
+ if (dws->cur_msg) {
+ spin_unlock_irqrestore(&dws->lock, flags);
+ return;
+ }
+
+ /* Extract head of queue */
+ dws->cur_msg = list_entry(dws->queue.next, struct spi_message, queue);
+ list_del_init(&dws->cur_msg->queue);
+
+ /* Initial message state*/
+ dws->cur_msg->state = START_STATE;
+ dws->cur_transfer = list_entry(dws->cur_msg->transfers.next,
+ struct spi_transfer,
+ transfer_list);
+ dws->cur_chip = spi_get_ctldata(dws->cur_msg->spi);
+
+ /* Mark as busy and launch transfers */
+ tasklet_schedule(&dws->pump_transfers);
+
+ dws->busy = 1;
+ spin_unlock_irqrestore(&dws->lock, flags);
+}
+
+/* spi_device use this to queue in their spi_msg */
+static int dw_spi_transfer(struct spi_device *spi, struct spi_message *msg)
+{
+ struct dw_spi *dws = spi_master_get_devdata(spi->master);
+ unsigned long flags;
+
+ spin_lock_irqsave(&dws->lock, flags);
+
+ if (dws->run == QUEUE_STOPPED) {
+ spin_unlock_irqrestore(&dws->lock, flags);
+ return -ESHUTDOWN;
+ }
+
+ msg->actual_length = 0;
+ msg->status = -EINPROGRESS;
+ msg->state = START_STATE;
+
+ list_add_tail(&msg->queue, &dws->queue);
+
+ if (dws->run == QUEUE_RUNNING && !dws->busy) {
+
+ if (dws->cur_transfer || dws->cur_msg)
+ queue_work(dws->workqueue,
+ &dws->pump_messages);
+ else {
+ /* If no other data transaction in air, just go */
+ spin_unlock_irqrestore(&dws->lock, flags);
+ pump_messages(&dws->pump_messages);
+ return 0;
+ }
+ }
+
+ spin_unlock_irqrestore(&dws->lock, flags);
+ return 0;
+}
+
+/* This may be called twice for each spi dev */
+static int dw_spi_setup(struct spi_device *spi)
+{
+ struct dw_spi_chip *chip_info = NULL;
+ struct chip_data *chip;
+
+ if (spi->bits_per_word != 8 && spi->bits_per_word != 16)
+ return -EINVAL;
+
+ /* Only alloc on first setup */
+ chip = spi_get_ctldata(spi);
+ if (!chip) {
+ chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL);
+ if (!chip)
+ return -ENOMEM;
+
+ chip->cs_control = null_cs_control;
+ chip->enable_dma = 0;
+ }
+
+ /*
+ * Protocol drivers may change the chip settings, so...
+ * if chip_info exists, use it
+ */
+ chip_info = spi->controller_data;
+
+ /* chip_info doesn't always exist */
+ if (chip_info) {
+ if (chip_info->cs_control)
+ chip->cs_control = chip_info->cs_control;
+
+ chip->poll_mode = chip_info->poll_mode;
+ chip->type = chip_info->type;
+
+ chip->rx_threshold = 0;
+ chip->tx_threshold = 0;
+
+ chip->enable_dma = chip_info->enable_dma;
+ }
+
+ if (spi->bits_per_word <= 8) {
+ chip->n_bytes = 1;
+ chip->dma_width = 1;
+ chip->read = u8_reader;
+ chip->write = u8_writer;
+ } else if (spi->bits_per_word <= 16) {
+ chip->n_bytes = 2;
+ chip->dma_width = 2;
+ chip->read = u16_reader;
+ chip->write = u16_writer;
+ } else {
+ /* Never take >16b case for MRST SPIC */
+ dev_err(&spi->dev, "invalid wordsize\n");
+ return -EINVAL;
+ }
+ chip->bits_per_word = spi->bits_per_word;
+
+ chip->speed_hz = spi->max_speed_hz;
+ if (chip->speed_hz)
+ chip->clk_div = 25000000 / chip->speed_hz;
+ else
+ chip->clk_div = 8; /* default value */
+
+ chip->tmode = 0; /* Tx & Rx */
+ /* Default SPI mode is SCPOL = 0, SCPH = 0 */
+ chip->cr0 = (chip->bits_per_word - 1)
+ | (chip->type << SPI_FRF_OFFSET)
+ | (spi->mode << SPI_MODE_OFFSET)
+ | (chip->tmode << SPI_TMOD_OFFSET);
+
+ spi_set_ctldata(spi, chip);
+ return 0;
+}
+
+static void dw_spi_cleanup(struct spi_device *spi)
+{
+ struct chip_data *chip = spi_get_ctldata(spi);
+ kfree(chip);
+}
+
+static int __init init_queue(struct dw_spi *dws)
+{
+ INIT_LIST_HEAD(&dws->queue);
+ spin_lock_init(&dws->lock);
+
+ dws->run = QUEUE_STOPPED;
+ dws->busy = 0;
+
+ tasklet_init(&dws->pump_transfers,
+ pump_transfers, (unsigned long)dws);
+
+ INIT_WORK(&dws->pump_messages, pump_messages);
+ dws->workqueue = create_singlethread_workqueue(
+ dev_name(dws->master->dev.parent));
+ if (dws->workqueue == NULL)
+ return -EBUSY;
+
+ return 0;
+}
+
+static int start_queue(struct dw_spi *dws)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&dws->lock, flags);
+
+ if (dws->run == QUEUE_RUNNING || dws->busy) {
+ spin_unlock_irqrestore(&dws->lock, flags);
+ return -EBUSY;
+ }
+
+ dws->run = QUEUE_RUNNING;
+ dws->cur_msg = NULL;
+ dws->cur_transfer = NULL;
+ dws->cur_chip = NULL;
+ dws->prev_chip = NULL;
+ spin_unlock_irqrestore(&dws->lock, flags);
+
+ queue_work(dws->workqueue, &dws->pump_messages);
+
+ return 0;
+}
+
+static int stop_queue(struct dw_spi *dws)
+{
+ unsigned long flags;
+ unsigned limit = 50;
+ int status = 0;
+
+ spin_lock_irqsave(&dws->lock, flags);
+ dws->run = QUEUE_STOPPED;
+ while (!list_empty(&dws->queue) && dws->busy && limit--) {
+ spin_unlock_irqrestore(&dws->lock, flags);
+ msleep(10);
+ spin_lock_irqsave(&dws->lock, flags);
+ }
+
+ if (!list_empty(&dws->queue) || dws->busy)
+ status = -EBUSY;
+ spin_unlock_irqrestore(&dws->lock, flags);
+
+ return status;
+}
+
+static int destroy_queue(struct dw_spi *dws)
+{
+ int status;
+
+ status = stop_queue(dws);
+ if (status != 0)
+ return status;
+ destroy_workqueue(dws->workqueue);
+ return 0;
+}
+
+/* Restart the controller, disable all interrupts, clean rx fifo */
+static void spi_hw_init(struct dw_spi *dws)
+{
+ spi_enable_chip(dws, 0);
+ spi_mask_intr(dws, 0xff);
+ spi_enable_chip(dws, 1);
+ flush(dws);
+}
+
+int __devinit dw_spi_add_host(struct dw_spi *dws)
+{
+ struct spi_master *master;
+ int ret;
+
+ BUG_ON(dws == NULL);
+
+ master = spi_alloc_master(dws->parent_dev, 0);
+ if (!master) {
+ ret = -ENOMEM;
+ goto exit;
+ }
+
+ dws->master = master;
+ dws->type = SSI_MOTO_SPI;
+ dws->prev_chip = NULL;
+ dws->dma_inited = 0;
+ dws->dma_addr = (dma_addr_t)(dws->paddr + 0x60);
+
+ ret = request_irq(dws->irq, dw_spi_irq, 0,
+ "dw_spi", dws);
+ if (ret < 0) {
+ dev_err(&master->dev, "can not get IRQ\n");
+ goto err_free_master;
+ }
+
+ master->mode_bits = SPI_CPOL | SPI_CPHA;
+ master->bus_num = dws->bus_num;
+ master->num_chipselect = dws->num_cs;
+ master->cleanup = dw_spi_cleanup;
+ master->setup = dw_spi_setup;
+ master->transfer = dw_spi_transfer;
+
+ dws->dma_inited = 0;
+
+ /* Basic HW init */
+ spi_hw_init(dws);
+
+ /* Initial and start queue */
+ ret = init_queue(dws);
+ if (ret) {
+ dev_err(&master->dev, "problem initializing queue\n");
+ goto err_diable_hw;
+ }
+ ret = start_queue(dws);
+ if (ret) {
+ dev_err(&master->dev, "problem starting queue\n");
+ goto err_diable_hw;
+ }
+
+ spi_master_set_devdata(master, dws);
+ ret = spi_register_master(master);
+ if (ret) {
+ dev_err(&master->dev, "problem registering spi master\n");
+ goto err_queue_alloc;
+ }
+
+ mrst_spi_debugfs_init(dws);
+ return 0;
+
+err_queue_alloc:
+ destroy_queue(dws);
+err_diable_hw:
+ spi_enable_chip(dws, 0);
+ free_irq(dws->irq, dws);
+err_free_master:
+ spi_master_put(master);
+exit:
+ return ret;
+}
+EXPORT_SYMBOL(dw_spi_add_host);
+
+void __devexit dw_spi_remove_host(struct dw_spi *dws)
+{
+ int status = 0;
+
+ if (!dws)
+ return;
+ mrst_spi_debugfs_remove(dws);
+
+ /* Remove the queue */
+ status = destroy_queue(dws);
+ if (status != 0)
+ dev_err(&dws->master->dev, "dw_spi_remove: workqueue will not "
+ "complete, message memory not freed\n");
+
+ spi_enable_chip(dws, 0);
+ /* Disable clk */
+ spi_set_clk(dws, 0);
+ free_irq(dws->irq, dws);
+
+ /* Disconnect from the SPI framework */
+ spi_unregister_master(dws->master);
+}
+
+int dw_spi_suspend_host(struct dw_spi *dws)
+{
+ int ret = 0;
+
+ ret = stop_queue(dws);
+ if (ret)
+ return ret;
+ spi_enable_chip(dws, 0);
+ spi_set_clk(dws, 0);
+ return ret;
+}
+EXPORT_SYMBOL(dw_spi_suspend_host);
+
+int dw_spi_resume_host(struct dw_spi *dws)
+{
+ int ret;
+
+ spi_hw_init(dws);
+ ret = start_queue(dws);
+ if (ret)
+ dev_err(&dws->master->dev, "fail to start queue (%d)\n", ret);
+ return ret;
+}
+EXPORT_SYMBOL(dw_spi_resume_host);
+
+MODULE_AUTHOR("Feng Tang <feng.tang@intel.com>");
+MODULE_DESCRIPTION("Driver for DesignWare SPI controller core");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/spi/dw_spi_pci.c b/drivers/spi/dw_spi_pci.c
new file mode 100644
index 000000000000..34ba69161734
--- /dev/null
+++ b/drivers/spi/dw_spi_pci.c
@@ -0,0 +1,169 @@
+/*
+ * mrst_spi_pci.c - PCI interface driver for DW SPI Core
+ *
+ * Copyright (c) 2009, Intel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation,
+ * Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/spi/dw_spi.h>
+#include <linux/spi/spi.h>
+
+#define DRIVER_NAME "dw_spi_pci"
+
+struct dw_spi_pci {
+ struct pci_dev *pdev;
+ struct dw_spi dws;
+};
+
+static int __devinit spi_pci_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct dw_spi_pci *dwpci;
+ struct dw_spi *dws;
+ int pci_bar = 0;
+ int ret;
+
+ printk(KERN_INFO "DW: found PCI SPI controller(ID: %04x:%04x)\n",
+ pdev->vendor, pdev->device);
+
+ ret = pci_enable_device(pdev);
+ if (ret)
+ return ret;
+
+ dwpci = kzalloc(sizeof(struct dw_spi_pci), GFP_KERNEL);
+ if (!dwpci) {
+ ret = -ENOMEM;
+ goto err_disable;
+ }
+
+ dwpci->pdev = pdev;
+ dws = &dwpci->dws;
+
+ /* Get basic io resource and map it */
+ dws->paddr = pci_resource_start(pdev, pci_bar);
+ dws->iolen = pci_resource_len(pdev, pci_bar);
+
+ ret = pci_request_region(pdev, pci_bar, dev_name(&pdev->dev));
+ if (ret)
+ goto err_kfree;
+
+ dws->regs = ioremap_nocache((unsigned long)dws->paddr,
+ pci_resource_len(pdev, pci_bar));
+ if (!dws->regs) {
+ ret = -ENOMEM;
+ goto err_release_reg;
+ }
+
+ dws->parent_dev = &pdev->dev;
+ dws->bus_num = 0;
+ dws->num_cs = 4;
+ dws->max_freq = 25000000; /* for Moorestwon */
+ dws->irq = pdev->irq;
+
+ ret = dw_spi_add_host(dws);
+ if (ret)
+ goto err_unmap;
+
+ /* PCI hook and SPI hook use the same drv data */
+ pci_set_drvdata(pdev, dwpci);
+ return 0;
+
+err_unmap:
+ iounmap(dws->regs);
+err_release_reg:
+ pci_release_region(pdev, pci_bar);
+err_kfree:
+ kfree(dwpci);
+err_disable:
+ pci_disable_device(pdev);
+ return ret;
+}
+
+static void __devexit spi_pci_remove(struct pci_dev *pdev)
+{
+ struct dw_spi_pci *dwpci = pci_get_drvdata(pdev);
+
+ pci_set_drvdata(pdev, NULL);
+ iounmap(dwpci->dws.regs);
+ pci_release_region(pdev, 0);
+ kfree(dwpci);
+ pci_disable_device(pdev);
+}
+
+#ifdef CONFIG_PM
+static int spi_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ struct dw_spi_pci *dwpci = pci_get_drvdata(pdev);
+ int ret;
+
+ ret = dw_spi_suspend_host(&dwpci->dws);
+ if (ret)
+ return ret;
+ pci_save_state(pdev);
+ pci_disable_device(pdev);
+ pci_set_power_state(pdev, pci_choose_state(pdev, state));
+ return ret;
+}
+
+static int spi_resume(struct pci_dev *pdev)
+{
+ struct dw_spi_pci *dwpci = pci_get_drvdata(pdev);
+ int ret;
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+ ret = pci_enable_device(pdev);
+ if (ret)
+ return ret;
+ return dw_spi_resume_host(&dwpci->dws);
+}
+#else
+#define spi_suspend NULL
+#define spi_resume NULL
+#endif
+
+static const struct pci_device_id pci_ids[] __devinitdata = {
+ /* Intel Moorestown platform SPI controller 0 */
+ { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x0800) },
+ {},
+};
+
+static struct pci_driver dw_spi_driver = {
+ .name = DRIVER_NAME,
+ .id_table = pci_ids,
+ .probe = spi_pci_probe,
+ .remove = __devexit_p(spi_pci_remove),
+ .suspend = spi_suspend,
+ .resume = spi_resume,
+};
+
+static int __init mrst_spi_init(void)
+{
+ return pci_register_driver(&dw_spi_driver);
+}
+
+static void __exit mrst_spi_exit(void)
+{
+ pci_unregister_driver(&dw_spi_driver);
+}
+
+module_init(mrst_spi_init);
+module_exit(mrst_spi_exit);
+
+MODULE_AUTHOR("Feng Tang <feng.tang@intel.com>");
+MODULE_DESCRIPTION("PCI interface driver for DW SPI Core");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 73e24ef5a2f9..1d41058bbab2 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -1294,7 +1294,7 @@ static int __init bfin_spi_probe(struct platform_device *pdev)
goto out_error_get_res;
}
- drv_data->regs_base = ioremap(res->start, (res->end - res->start + 1));
+ drv_data->regs_base = ioremap(res->start, resource_size(res));
if (drv_data->regs_base == NULL) {
dev_err(dev, "Cannot map IO\n");
status = -ENXIO;
diff --git a/drivers/spi/spi_mpc8xxx.c b/drivers/spi/spi_mpc8xxx.c
index e9390d747bfc..1fb2a6ea328c 100644
--- a/drivers/spi/spi_mpc8xxx.c
+++ b/drivers/spi/spi_mpc8xxx.c
@@ -1013,7 +1013,7 @@ mpc8xxx_spi_probe(struct device *dev, struct resource *mem, unsigned int irq)
init_completion(&mpc8xxx_spi->done);
- mpc8xxx_spi->base = ioremap(mem->start, mem->end - mem->start + 1);
+ mpc8xxx_spi->base = ioremap(mem->start, resource_size(mem));
if (mpc8xxx_spi->base == NULL) {
ret = -ENOMEM;
goto err_ioremap;
diff --git a/drivers/spi/spi_s3c24xx.c b/drivers/spi/spi_s3c24xx.c
index 276591569c8b..c010733877ae 100644
--- a/drivers/spi/spi_s3c24xx.c
+++ b/drivers/spi/spi_s3c24xx.c
@@ -1,7 +1,7 @@
/* linux/drivers/spi/spi_s3c24xx.c
*
* Copyright (c) 2006 Ben Dooks
- * Copyright (c) 2006 Simtec Electronics
+ * Copyright 2006-2009 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* This program is free software; you can redistribute it and/or modify
@@ -28,6 +28,11 @@
#include <plat/regs-spi.h>
#include <mach/spi.h>
+#include <plat/fiq.h>
+#include <asm/fiq.h>
+
+#include "spi_s3c24xx_fiq.h"
+
/**
* s3c24xx_spi_devstate - per device data
* @hz: Last frequency calculated for @sppre field.
@@ -42,6 +47,13 @@ struct s3c24xx_spi_devstate {
u8 sppre;
};
+enum spi_fiq_mode {
+ FIQ_MODE_NONE = 0,
+ FIQ_MODE_TX = 1,
+ FIQ_MODE_RX = 2,
+ FIQ_MODE_TXRX = 3,
+};
+
struct s3c24xx_spi {
/* bitbang has to be first */
struct spi_bitbang bitbang;
@@ -52,6 +64,11 @@ struct s3c24xx_spi {
int len;
int count;
+ struct fiq_handler fiq_handler;
+ enum spi_fiq_mode fiq_mode;
+ unsigned char fiq_inuse;
+ unsigned char fiq_claimed;
+
void (*set_cs)(struct s3c2410_spi_info *spi,
int cs, int pol);
@@ -67,6 +84,7 @@ struct s3c24xx_spi {
struct s3c2410_spi_info *pdata;
};
+
#define SPCON_DEFAULT (S3C2410_SPCON_MSTR | S3C2410_SPCON_SMOD_INT)
#define SPPIN_DEFAULT (S3C2410_SPPIN_KEEP)
@@ -127,7 +145,7 @@ static int s3c24xx_spi_update_state(struct spi_device *spi,
}
if (spi->mode != cs->mode) {
- u8 spcon = SPCON_DEFAULT;
+ u8 spcon = SPCON_DEFAULT | S3C2410_SPCON_ENSCK;
if (spi->mode & SPI_CPHA)
spcon |= S3C2410_SPCON_CPHA_FMTB;
@@ -214,13 +232,196 @@ static inline unsigned int hw_txbyte(struct s3c24xx_spi *hw, int count)
return hw->tx ? hw->tx[count] : 0;
}
+#ifdef CONFIG_SPI_S3C24XX_FIQ
+/* Support for FIQ based pseudo-DMA to improve the transfer speed.
+ *
+ * This code uses the assembly helper in spi_s3c24xx_spi.S which is
+ * used by the FIQ core to move data between main memory and the peripheral
+ * block. Since this is code running on the processor, there is no problem
+ * with cache coherency of the buffers, so we can use any buffer we like.
+ */
+
+/**
+ * struct spi_fiq_code - FIQ code and header
+ * @length: The length of the code fragment, excluding this header.
+ * @ack_offset: The offset from @data to the word to place the IRQ ACK bit at.
+ * @data: The code itself to install as a FIQ handler.
+ */
+struct spi_fiq_code {
+ u32 length;
+ u32 ack_offset;
+ u8 data[0];
+};
+
+extern struct spi_fiq_code s3c24xx_spi_fiq_txrx;
+extern struct spi_fiq_code s3c24xx_spi_fiq_tx;
+extern struct spi_fiq_code s3c24xx_spi_fiq_rx;
+
+/**
+ * ack_bit - turn IRQ into IRQ acknowledgement bit
+ * @irq: The interrupt number
+ *
+ * Returns the bit to write to the interrupt acknowledge register.
+ */
+static inline u32 ack_bit(unsigned int irq)
+{
+ return 1 << (irq - IRQ_EINT0);
+}
+
+/**
+ * s3c24xx_spi_tryfiq - attempt to claim and setup FIQ for transfer
+ * @hw: The hardware state.
+ *
+ * Claim the FIQ handler (only one can be active at any one time) and
+ * then setup the correct transfer code for this transfer.
+ *
+ * This call updates all the necessary state information if sucessful,
+ * so the caller does not need to do anything more than start the transfer
+ * as normal, since the IRQ will have been re-routed to the FIQ handler.
+*/
+void s3c24xx_spi_tryfiq(struct s3c24xx_spi *hw)
+{
+ struct pt_regs regs;
+ enum spi_fiq_mode mode;
+ struct spi_fiq_code *code;
+ int ret;
+
+ if (!hw->fiq_claimed) {
+ /* try and claim fiq if we haven't got it, and if not
+ * then return and simply use another transfer method */
+
+ ret = claim_fiq(&hw->fiq_handler);
+ if (ret)
+ return;
+ }
+
+ if (hw->tx && !hw->rx)
+ mode = FIQ_MODE_TX;
+ else if (hw->rx && !hw->tx)
+ mode = FIQ_MODE_RX;
+ else
+ mode = FIQ_MODE_TXRX;
+
+ regs.uregs[fiq_rspi] = (long)hw->regs;
+ regs.uregs[fiq_rrx] = (long)hw->rx;
+ regs.uregs[fiq_rtx] = (long)hw->tx + 1;
+ regs.uregs[fiq_rcount] = hw->len - 1;
+ regs.uregs[fiq_rirq] = (long)S3C24XX_VA_IRQ;
+
+ set_fiq_regs(&regs);
+
+ if (hw->fiq_mode != mode) {
+ u32 *ack_ptr;
+
+ hw->fiq_mode = mode;
+
+ switch (mode) {
+ case FIQ_MODE_TX:
+ code = &s3c24xx_spi_fiq_tx;
+ break;
+ case FIQ_MODE_RX:
+ code = &s3c24xx_spi_fiq_rx;
+ break;
+ case FIQ_MODE_TXRX:
+ code = &s3c24xx_spi_fiq_txrx;
+ break;
+ default:
+ code = NULL;
+ }
+
+ BUG_ON(!code);
+
+ ack_ptr = (u32 *)&code->data[code->ack_offset];
+ *ack_ptr = ack_bit(hw->irq);
+
+ set_fiq_handler(&code->data, code->length);
+ }
+
+ s3c24xx_set_fiq(hw->irq, true);
+
+ hw->fiq_mode = mode;
+ hw->fiq_inuse = 1;
+}
+
+/**
+ * s3c24xx_spi_fiqop - FIQ core code callback
+ * @pw: Data registered with the handler
+ * @release: Whether this is a release or a return.
+ *
+ * Called by the FIQ code when another module wants to use the FIQ, so
+ * return whether we are currently using this or not and then update our
+ * internal state.
+ */
+static int s3c24xx_spi_fiqop(void *pw, int release)
+{
+ struct s3c24xx_spi *hw = pw;
+ int ret = 0;
+
+ if (release) {
+ if (hw->fiq_inuse)
+ ret = -EBUSY;
+
+ /* note, we do not need to unroute the FIQ, as the FIQ
+ * vector code de-routes it to signal the end of transfer */
+
+ hw->fiq_mode = FIQ_MODE_NONE;
+ hw->fiq_claimed = 0;
+ } else {
+ hw->fiq_claimed = 1;
+ }
+
+ return ret;
+}
+
+/**
+ * s3c24xx_spi_initfiq - setup the information for the FIQ core
+ * @hw: The hardware state.
+ *
+ * Setup the fiq_handler block to pass to the FIQ core.
+ */
+static inline void s3c24xx_spi_initfiq(struct s3c24xx_spi *hw)
+{
+ hw->fiq_handler.dev_id = hw;
+ hw->fiq_handler.name = dev_name(hw->dev);
+ hw->fiq_handler.fiq_op = s3c24xx_spi_fiqop;
+}
+
+/**
+ * s3c24xx_spi_usefiq - return if we should be using FIQ.
+ * @hw: The hardware state.
+ *
+ * Return true if the platform data specifies whether this channel is
+ * allowed to use the FIQ.
+ */
+static inline bool s3c24xx_spi_usefiq(struct s3c24xx_spi *hw)
+{
+ return hw->pdata->use_fiq;
+}
+
+/**
+ * s3c24xx_spi_usingfiq - return if channel is using FIQ
+ * @spi: The hardware state.
+ *
+ * Return whether the channel is currently using the FIQ (separate from
+ * whether the FIQ is claimed).
+ */
+static inline bool s3c24xx_spi_usingfiq(struct s3c24xx_spi *spi)
+{
+ return spi->fiq_inuse;
+}
+#else
+
+static inline void s3c24xx_spi_initfiq(struct s3c24xx_spi *s) { }
+static inline void s3c24xx_spi_tryfiq(struct s3c24xx_spi *s) { }
+static inline bool s3c24xx_spi_usefiq(struct s3c24xx_spi *s) { return false; }
+static inline bool s3c24xx_spi_usingfiq(struct s3c24xx_spi *s) { return false; }
+
+#endif /* CONFIG_SPI_S3C24XX_FIQ */
+
static int s3c24xx_spi_txrx(struct spi_device *spi, struct spi_transfer *t)
{
struct s3c24xx_spi *hw = to_hw(spi);
- dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
- t->tx_buf, t->rx_buf, t->len);
-
hw->tx = t->tx_buf;
hw->rx = t->rx_buf;
hw->len = t->len;
@@ -228,11 +429,14 @@ static int s3c24xx_spi_txrx(struct spi_device *spi, struct spi_transfer *t)
init_completion(&hw->done);
+ hw->fiq_inuse = 0;
+ if (s3c24xx_spi_usefiq(hw) && t->len >= 3)
+ s3c24xx_spi_tryfiq(hw);
+
/* send the first byte */
writeb(hw_txbyte(hw, 0), hw->regs + S3C2410_SPTDAT);
wait_for_completion(&hw->done);
-
return hw->count;
}
@@ -254,17 +458,27 @@ static irqreturn_t s3c24xx_spi_irq(int irq, void *dev)
goto irq_done;
}
- hw->count++;
+ if (!s3c24xx_spi_usingfiq(hw)) {
+ hw->count++;
- if (hw->rx)
- hw->rx[count] = readb(hw->regs + S3C2410_SPRDAT);
+ if (hw->rx)
+ hw->rx[count] = readb(hw->regs + S3C2410_SPRDAT);
- count++;
+ count++;
+
+ if (count < hw->len)
+ writeb(hw_txbyte(hw, count), hw->regs + S3C2410_SPTDAT);
+ else
+ complete(&hw->done);
+ } else {
+ hw->count = hw->len;
+ hw->fiq_inuse = 0;
+
+ if (hw->rx)
+ hw->rx[hw->len-1] = readb(hw->regs + S3C2410_SPRDAT);
- if (count < hw->len)
- writeb(hw_txbyte(hw, count), hw->regs + S3C2410_SPTDAT);
- else
complete(&hw->done);
+ }
irq_done:
return IRQ_HANDLED;
@@ -322,6 +536,10 @@ static int __init s3c24xx_spi_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, hw);
init_completion(&hw->done);
+ /* initialise fiq handler */
+
+ s3c24xx_spi_initfiq(hw);
+
/* setup the master state. */
/* the spi->mode bits understood by this driver: */
diff --git a/drivers/spi/spi_s3c24xx_fiq.S b/drivers/spi/spi_s3c24xx_fiq.S
new file mode 100644
index 000000000000..3793cae361db
--- /dev/null
+++ b/drivers/spi/spi_s3c24xx_fiq.S
@@ -0,0 +1,116 @@
+/* linux/drivers/spi/spi_s3c24xx_fiq.S
+ *
+ * Copyright 2009 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C24XX SPI - FIQ pseudo-DMA transfer code
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+#include <mach/map.h>
+#include <mach/regs-irq.h>
+#include <plat/regs-spi.h>
+
+#include "spi_s3c24xx_fiq.h"
+
+ .text
+
+ @ entry to these routines is as follows, with the register names
+ @ defined in fiq.h so that they can be shared with the C files which
+ @ setup the calling registers.
+ @
+ @ fiq_rirq The base of the IRQ registers to find S3C2410_SRCPND
+ @ fiq_rtmp Temporary register to hold tx/rx data
+ @ fiq_rspi The base of the SPI register block
+ @ fiq_rtx The tx buffer pointer
+ @ fiq_rrx The rx buffer pointer
+ @ fiq_rcount The number of bytes to move
+
+ @ each entry starts with a word entry of how long it is
+ @ and an offset to the irq acknowledgment word
+
+ENTRY(s3c24xx_spi_fiq_rx)
+s3c24xx_spi_fix_rx:
+ .word fiq_rx_end - fiq_rx_start
+ .word fiq_rx_irq_ack - fiq_rx_start
+fiq_rx_start:
+ ldr fiq_rtmp, fiq_rx_irq_ack
+ str fiq_rtmp, [ fiq_rirq, # S3C2410_SRCPND - S3C24XX_VA_IRQ ]
+
+ ldrb fiq_rtmp, [ fiq_rspi, # S3C2410_SPRDAT ]
+ strb fiq_rtmp, [ fiq_rrx ], #1
+
+ mov fiq_rtmp, #0xff
+ strb fiq_rtmp, [ fiq_rspi, # S3C2410_SPTDAT ]
+
+ subs fiq_rcount, fiq_rcount, #1
+ subnes pc, lr, #4 @@ return, still have work to do
+
+ @@ set IRQ controller so that next op will trigger IRQ
+ mov fiq_rtmp, #0
+ str fiq_rtmp, [ fiq_rirq, # S3C2410_INTMOD - S3C24XX_VA_IRQ ]
+ subs pc, lr, #4
+
+fiq_rx_irq_ack:
+ .word 0
+fiq_rx_end:
+
+ENTRY(s3c24xx_spi_fiq_txrx)
+s3c24xx_spi_fiq_txrx:
+ .word fiq_txrx_end - fiq_txrx_start
+ .word fiq_txrx_irq_ack - fiq_txrx_start
+fiq_txrx_start:
+
+ ldrb fiq_rtmp, [ fiq_rspi, # S3C2410_SPRDAT ]
+ strb fiq_rtmp, [ fiq_rrx ], #1
+
+ ldr fiq_rtmp, fiq_txrx_irq_ack
+ str fiq_rtmp, [ fiq_rirq, # S3C2410_SRCPND - S3C24XX_VA_IRQ ]
+
+ ldrb fiq_rtmp, [ fiq_rtx ], #1
+ strb fiq_rtmp, [ fiq_rspi, # S3C2410_SPTDAT ]
+
+ subs fiq_rcount, fiq_rcount, #1
+ subnes pc, lr, #4 @@ return, still have work to do
+
+ mov fiq_rtmp, #0
+ str fiq_rtmp, [ fiq_rirq, # S3C2410_INTMOD - S3C24XX_VA_IRQ ]
+ subs pc, lr, #4
+
+fiq_txrx_irq_ack:
+ .word 0
+
+fiq_txrx_end:
+
+ENTRY(s3c24xx_spi_fiq_tx)
+s3c24xx_spi_fix_tx:
+ .word fiq_tx_end - fiq_tx_start
+ .word fiq_tx_irq_ack - fiq_tx_start
+fiq_tx_start:
+ ldrb fiq_rtmp, [ fiq_rspi, # S3C2410_SPRDAT ]
+
+ ldr fiq_rtmp, fiq_tx_irq_ack
+ str fiq_rtmp, [ fiq_rirq, # S3C2410_SRCPND - S3C24XX_VA_IRQ ]
+
+ ldrb fiq_rtmp, [ fiq_rtx ], #1
+ strb fiq_rtmp, [ fiq_rspi, # S3C2410_SPTDAT ]
+
+ subs fiq_rcount, fiq_rcount, #1
+ subnes pc, lr, #4 @@ return, still have work to do
+
+ mov fiq_rtmp, #0
+ str fiq_rtmp, [ fiq_rirq, # S3C2410_INTMOD - S3C24XX_VA_IRQ ]
+ subs pc, lr, #4
+
+fiq_tx_irq_ack:
+ .word 0
+
+fiq_tx_end:
+
+ .end
diff --git a/drivers/spi/spi_s3c24xx_fiq.h b/drivers/spi/spi_s3c24xx_fiq.h
new file mode 100644
index 000000000000..a5950bb25b51
--- /dev/null
+++ b/drivers/spi/spi_s3c24xx_fiq.h
@@ -0,0 +1,26 @@
+/* linux/drivers/spi/spi_s3c24xx_fiq.h
+ *
+ * Copyright 2009 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C24XX SPI - FIQ pseudo-DMA transfer support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* We have R8 through R13 to play with */
+
+#ifdef __ASSEMBLY__
+#define __REG_NR(x) r##x
+#else
+#define __REG_NR(x) (x)
+#endif
+
+#define fiq_rspi __REG_NR(8)
+#define fiq_rtmp __REG_NR(9)
+#define fiq_rrx __REG_NR(10)
+#define fiq_rtx __REG_NR(11)
+#define fiq_rcount __REG_NR(12)
+#define fiq_rirq __REG_NR(13)
diff --git a/drivers/spi/spi_s3c64xx.c b/drivers/spi/spi_s3c64xx.c
new file mode 100644
index 000000000000..88a456dba967
--- /dev/null
+++ b/drivers/spi/spi_s3c64xx.c
@@ -0,0 +1,1196 @@
+/* linux/drivers/spi/spi_s3c64xx.c
+ *
+ * Copyright (C) 2009 Samsung Electronics Ltd.
+ * Jaswinder Singh <jassi.brar@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/workqueue.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+
+#include <mach/dma.h>
+#include <plat/spi.h>
+
+/* Registers and bit-fields */
+
+#define S3C64XX_SPI_CH_CFG 0x00
+#define S3C64XX_SPI_CLK_CFG 0x04
+#define S3C64XX_SPI_MODE_CFG 0x08
+#define S3C64XX_SPI_SLAVE_SEL 0x0C
+#define S3C64XX_SPI_INT_EN 0x10
+#define S3C64XX_SPI_STATUS 0x14
+#define S3C64XX_SPI_TX_DATA 0x18
+#define S3C64XX_SPI_RX_DATA 0x1C
+#define S3C64XX_SPI_PACKET_CNT 0x20
+#define S3C64XX_SPI_PENDING_CLR 0x24
+#define S3C64XX_SPI_SWAP_CFG 0x28
+#define S3C64XX_SPI_FB_CLK 0x2C
+
+#define S3C64XX_SPI_CH_HS_EN (1<<6) /* High Speed Enable */
+#define S3C64XX_SPI_CH_SW_RST (1<<5)
+#define S3C64XX_SPI_CH_SLAVE (1<<4)
+#define S3C64XX_SPI_CPOL_L (1<<3)
+#define S3C64XX_SPI_CPHA_B (1<<2)
+#define S3C64XX_SPI_CH_RXCH_ON (1<<1)
+#define S3C64XX_SPI_CH_TXCH_ON (1<<0)
+
+#define S3C64XX_SPI_CLKSEL_SRCMSK (3<<9)
+#define S3C64XX_SPI_CLKSEL_SRCSHFT 9
+#define S3C64XX_SPI_ENCLK_ENABLE (1<<8)
+#define S3C64XX_SPI_PSR_MASK 0xff
+
+#define S3C64XX_SPI_MODE_CH_TSZ_BYTE (0<<29)
+#define S3C64XX_SPI_MODE_CH_TSZ_HALFWORD (1<<29)
+#define S3C64XX_SPI_MODE_CH_TSZ_WORD (2<<29)
+#define S3C64XX_SPI_MODE_CH_TSZ_MASK (3<<29)
+#define S3C64XX_SPI_MODE_BUS_TSZ_BYTE (0<<17)
+#define S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD (1<<17)
+#define S3C64XX_SPI_MODE_BUS_TSZ_WORD (2<<17)
+#define S3C64XX_SPI_MODE_BUS_TSZ_MASK (3<<17)
+#define S3C64XX_SPI_MODE_RXDMA_ON (1<<2)
+#define S3C64XX_SPI_MODE_TXDMA_ON (1<<1)
+#define S3C64XX_SPI_MODE_4BURST (1<<0)
+
+#define S3C64XX_SPI_SLAVE_AUTO (1<<1)
+#define S3C64XX_SPI_SLAVE_SIG_INACT (1<<0)
+
+#define S3C64XX_SPI_ACT(c) writel(0, (c)->regs + S3C64XX_SPI_SLAVE_SEL)
+
+#define S3C64XX_SPI_DEACT(c) writel(S3C64XX_SPI_SLAVE_SIG_INACT, \
+ (c)->regs + S3C64XX_SPI_SLAVE_SEL)
+
+#define S3C64XX_SPI_INT_TRAILING_EN (1<<6)
+#define S3C64XX_SPI_INT_RX_OVERRUN_EN (1<<5)
+#define S3C64XX_SPI_INT_RX_UNDERRUN_EN (1<<4)
+#define S3C64XX_SPI_INT_TX_OVERRUN_EN (1<<3)
+#define S3C64XX_SPI_INT_TX_UNDERRUN_EN (1<<2)
+#define S3C64XX_SPI_INT_RX_FIFORDY_EN (1<<1)
+#define S3C64XX_SPI_INT_TX_FIFORDY_EN (1<<0)
+
+#define S3C64XX_SPI_ST_RX_OVERRUN_ERR (1<<5)
+#define S3C64XX_SPI_ST_RX_UNDERRUN_ERR (1<<4)
+#define S3C64XX_SPI_ST_TX_OVERRUN_ERR (1<<3)
+#define S3C64XX_SPI_ST_TX_UNDERRUN_ERR (1<<2)
+#define S3C64XX_SPI_ST_RX_FIFORDY (1<<1)
+#define S3C64XX_SPI_ST_TX_FIFORDY (1<<0)
+
+#define S3C64XX_SPI_PACKET_CNT_EN (1<<16)
+
+#define S3C64XX_SPI_PND_TX_UNDERRUN_CLR (1<<4)
+#define S3C64XX_SPI_PND_TX_OVERRUN_CLR (1<<3)
+#define S3C64XX_SPI_PND_RX_UNDERRUN_CLR (1<<2)
+#define S3C64XX_SPI_PND_RX_OVERRUN_CLR (1<<1)
+#define S3C64XX_SPI_PND_TRAILING_CLR (1<<0)
+
+#define S3C64XX_SPI_SWAP_RX_HALF_WORD (1<<7)
+#define S3C64XX_SPI_SWAP_RX_BYTE (1<<6)
+#define S3C64XX_SPI_SWAP_RX_BIT (1<<5)
+#define S3C64XX_SPI_SWAP_RX_EN (1<<4)
+#define S3C64XX_SPI_SWAP_TX_HALF_WORD (1<<3)
+#define S3C64XX_SPI_SWAP_TX_BYTE (1<<2)
+#define S3C64XX_SPI_SWAP_TX_BIT (1<<1)
+#define S3C64XX_SPI_SWAP_TX_EN (1<<0)
+
+#define S3C64XX_SPI_FBCLK_MSK (3<<0)
+
+#define S3C64XX_SPI_ST_TRLCNTZ(v, i) ((((v) >> (i)->rx_lvl_offset) & \
+ (((i)->fifo_lvl_mask + 1))) \
+ ? 1 : 0)
+
+#define S3C64XX_SPI_ST_TX_DONE(v, i) ((((v) >> (i)->rx_lvl_offset) & \
+ (((i)->fifo_lvl_mask + 1) << 1)) \
+ ? 1 : 0)
+#define TX_FIFO_LVL(v, i) (((v) >> 6) & (i)->fifo_lvl_mask)
+#define RX_FIFO_LVL(v, i) (((v) >> (i)->rx_lvl_offset) & (i)->fifo_lvl_mask)
+
+#define S3C64XX_SPI_MAX_TRAILCNT 0x3ff
+#define S3C64XX_SPI_TRAILCNT_OFF 19
+
+#define S3C64XX_SPI_TRAILCNT S3C64XX_SPI_MAX_TRAILCNT
+
+#define msecs_to_loops(t) (loops_per_jiffy / 1000 * HZ * t)
+
+#define SUSPND (1<<0)
+#define SPIBUSY (1<<1)
+#define RXBUSY (1<<2)
+#define TXBUSY (1<<3)
+
+/**
+ * struct s3c64xx_spi_driver_data - Runtime info holder for SPI driver.
+ * @clk: Pointer to the spi clock.
+ * @master: Pointer to the SPI Protocol master.
+ * @workqueue: Work queue for the SPI xfer requests.
+ * @cntrlr_info: Platform specific data for the controller this driver manages.
+ * @tgl_spi: Pointer to the last CS left untoggled by the cs_change hint.
+ * @work: Work
+ * @queue: To log SPI xfer requests.
+ * @lock: Controller specific lock.
+ * @state: Set of FLAGS to indicate status.
+ * @rx_dmach: Controller's DMA channel for Rx.
+ * @tx_dmach: Controller's DMA channel for Tx.
+ * @sfr_start: BUS address of SPI controller regs.
+ * @regs: Pointer to ioremap'ed controller registers.
+ * @xfer_completion: To indicate completion of xfer task.
+ * @cur_mode: Stores the active configuration of the controller.
+ * @cur_bpw: Stores the active bits per word settings.
+ * @cur_speed: Stores the active xfer clock speed.
+ */
+struct s3c64xx_spi_driver_data {
+ void __iomem *regs;
+ struct clk *clk;
+ struct platform_device *pdev;
+ struct spi_master *master;
+ struct workqueue_struct *workqueue;
+ struct s3c64xx_spi_cntrlr_info *cntrlr_info;
+ struct spi_device *tgl_spi;
+ struct work_struct work;
+ struct list_head queue;
+ spinlock_t lock;
+ enum dma_ch rx_dmach;
+ enum dma_ch tx_dmach;
+ unsigned long sfr_start;
+ struct completion xfer_completion;
+ unsigned state;
+ unsigned cur_mode, cur_bpw;
+ unsigned cur_speed;
+};
+
+static struct s3c2410_dma_client s3c64xx_spi_dma_client = {
+ .name = "samsung-spi-dma",
+};
+
+static void flush_fifo(struct s3c64xx_spi_driver_data *sdd)
+{
+ struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+ void __iomem *regs = sdd->regs;
+ unsigned long loops;
+ u32 val;
+
+ writel(0, regs + S3C64XX_SPI_PACKET_CNT);
+
+ val = readl(regs + S3C64XX_SPI_CH_CFG);
+ val |= S3C64XX_SPI_CH_SW_RST;
+ val &= ~S3C64XX_SPI_CH_HS_EN;
+ writel(val, regs + S3C64XX_SPI_CH_CFG);
+
+ /* Flush TxFIFO*/
+ loops = msecs_to_loops(1);
+ do {
+ val = readl(regs + S3C64XX_SPI_STATUS);
+ } while (TX_FIFO_LVL(val, sci) && loops--);
+
+ /* Flush RxFIFO*/
+ loops = msecs_to_loops(1);
+ do {
+ val = readl(regs + S3C64XX_SPI_STATUS);
+ if (RX_FIFO_LVL(val, sci))
+ readl(regs + S3C64XX_SPI_RX_DATA);
+ else
+ break;
+ } while (loops--);
+
+ val = readl(regs + S3C64XX_SPI_CH_CFG);
+ val &= ~S3C64XX_SPI_CH_SW_RST;
+ writel(val, regs + S3C64XX_SPI_CH_CFG);
+
+ val = readl(regs + S3C64XX_SPI_MODE_CFG);
+ val &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON);
+ writel(val, regs + S3C64XX_SPI_MODE_CFG);
+
+ val = readl(regs + S3C64XX_SPI_CH_CFG);
+ val &= ~(S3C64XX_SPI_CH_RXCH_ON | S3C64XX_SPI_CH_TXCH_ON);
+ writel(val, regs + S3C64XX_SPI_CH_CFG);
+}
+
+static void enable_datapath(struct s3c64xx_spi_driver_data *sdd,
+ struct spi_device *spi,
+ struct spi_transfer *xfer, int dma_mode)
+{
+ struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+ void __iomem *regs = sdd->regs;
+ u32 modecfg, chcfg;
+
+ modecfg = readl(regs + S3C64XX_SPI_MODE_CFG);
+ modecfg &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON);
+
+ chcfg = readl(regs + S3C64XX_SPI_CH_CFG);
+ chcfg &= ~S3C64XX_SPI_CH_TXCH_ON;
+
+ if (dma_mode) {
+ chcfg &= ~S3C64XX_SPI_CH_RXCH_ON;
+ } else {
+ /* Always shift in data in FIFO, even if xfer is Tx only,
+ * this helps setting PCKT_CNT value for generating clocks
+ * as exactly needed.
+ */
+ chcfg |= S3C64XX_SPI_CH_RXCH_ON;
+ writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
+ | S3C64XX_SPI_PACKET_CNT_EN,
+ regs + S3C64XX_SPI_PACKET_CNT);
+ }
+
+ if (xfer->tx_buf != NULL) {
+ sdd->state |= TXBUSY;
+ chcfg |= S3C64XX_SPI_CH_TXCH_ON;
+ if (dma_mode) {
+ modecfg |= S3C64XX_SPI_MODE_TXDMA_ON;
+ s3c2410_dma_config(sdd->tx_dmach, 1);
+ s3c2410_dma_enqueue(sdd->tx_dmach, (void *)sdd,
+ xfer->tx_dma, xfer->len);
+ s3c2410_dma_ctrl(sdd->tx_dmach, S3C2410_DMAOP_START);
+ } else {
+ unsigned char *buf = (unsigned char *) xfer->tx_buf;
+ int i = 0;
+ while (i < xfer->len)
+ writeb(buf[i++], regs + S3C64XX_SPI_TX_DATA);
+ }
+ }
+
+ if (xfer->rx_buf != NULL) {
+ sdd->state |= RXBUSY;
+
+ if (sci->high_speed && sdd->cur_speed >= 30000000UL
+ && !(sdd->cur_mode & SPI_CPHA))
+ chcfg |= S3C64XX_SPI_CH_HS_EN;
+
+ if (dma_mode) {
+ modecfg |= S3C64XX_SPI_MODE_RXDMA_ON;
+ chcfg |= S3C64XX_SPI_CH_RXCH_ON;
+ writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
+ | S3C64XX_SPI_PACKET_CNT_EN,
+ regs + S3C64XX_SPI_PACKET_CNT);
+ s3c2410_dma_config(sdd->rx_dmach, 1);
+ s3c2410_dma_enqueue(sdd->rx_dmach, (void *)sdd,
+ xfer->rx_dma, xfer->len);
+ s3c2410_dma_ctrl(sdd->rx_dmach, S3C2410_DMAOP_START);
+ }
+ }
+
+ writel(modecfg, regs + S3C64XX_SPI_MODE_CFG);
+ writel(chcfg, regs + S3C64XX_SPI_CH_CFG);
+}
+
+static inline void enable_cs(struct s3c64xx_spi_driver_data *sdd,
+ struct spi_device *spi)
+{
+ struct s3c64xx_spi_csinfo *cs;
+
+ if (sdd->tgl_spi != NULL) { /* If last device toggled after mssg */
+ if (sdd->tgl_spi != spi) { /* if last mssg on diff device */
+ /* Deselect the last toggled device */
+ cs = sdd->tgl_spi->controller_data;
+ cs->set_level(spi->mode & SPI_CS_HIGH ? 0 : 1);
+ }
+ sdd->tgl_spi = NULL;
+ }
+
+ cs = spi->controller_data;
+ cs->set_level(spi->mode & SPI_CS_HIGH ? 1 : 0);
+}
+
+static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd,
+ struct spi_transfer *xfer, int dma_mode)
+{
+ struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+ void __iomem *regs = sdd->regs;
+ unsigned long val;
+ int ms;
+
+ /* millisecs to xfer 'len' bytes @ 'cur_speed' */
+ ms = xfer->len * 8 * 1000 / sdd->cur_speed;
+ ms += 5; /* some tolerance */
+
+ if (dma_mode) {
+ val = msecs_to_jiffies(ms) + 10;
+ val = wait_for_completion_timeout(&sdd->xfer_completion, val);
+ } else {
+ val = msecs_to_loops(ms);
+ do {
+ val = readl(regs + S3C64XX_SPI_STATUS);
+ } while (RX_FIFO_LVL(val, sci) < xfer->len && --val);
+ }
+
+ if (!val)
+ return -EIO;
+
+ if (dma_mode) {
+ u32 status;
+
+ /*
+ * DmaTx returns after simply writing data in the FIFO,
+ * w/o waiting for real transmission on the bus to finish.
+ * DmaRx returns only after Dma read data from FIFO which
+ * needs bus transmission to finish, so we don't worry if
+ * Xfer involved Rx(with or without Tx).
+ */
+ if (xfer->rx_buf == NULL) {
+ val = msecs_to_loops(10);
+ status = readl(regs + S3C64XX_SPI_STATUS);
+ while ((TX_FIFO_LVL(status, sci)
+ || !S3C64XX_SPI_ST_TX_DONE(status, sci))
+ && --val) {
+ cpu_relax();
+ status = readl(regs + S3C64XX_SPI_STATUS);
+ }
+
+ if (!val)
+ return -EIO;
+ }
+ } else {
+ unsigned char *buf;
+ int i;
+
+ /* If it was only Tx */
+ if (xfer->rx_buf == NULL) {
+ sdd->state &= ~TXBUSY;
+ return 0;
+ }
+
+ i = 0;
+ buf = xfer->rx_buf;
+ while (i < xfer->len)
+ buf[i++] = readb(regs + S3C64XX_SPI_RX_DATA);
+
+ sdd->state &= ~RXBUSY;
+ }
+
+ return 0;
+}
+
+static inline void disable_cs(struct s3c64xx_spi_driver_data *sdd,
+ struct spi_device *spi)
+{
+ struct s3c64xx_spi_csinfo *cs = spi->controller_data;
+
+ if (sdd->tgl_spi == spi)
+ sdd->tgl_spi = NULL;
+
+ cs->set_level(spi->mode & SPI_CS_HIGH ? 0 : 1);
+}
+
+static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
+{
+ struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+ void __iomem *regs = sdd->regs;
+ u32 val;
+
+ /* Disable Clock */
+ val = readl(regs + S3C64XX_SPI_CLK_CFG);
+ val &= ~S3C64XX_SPI_ENCLK_ENABLE;
+ writel(val, regs + S3C64XX_SPI_CLK_CFG);
+
+ /* Set Polarity and Phase */
+ val = readl(regs + S3C64XX_SPI_CH_CFG);
+ val &= ~(S3C64XX_SPI_CH_SLAVE |
+ S3C64XX_SPI_CPOL_L |
+ S3C64XX_SPI_CPHA_B);
+
+ if (sdd->cur_mode & SPI_CPOL)
+ val |= S3C64XX_SPI_CPOL_L;
+
+ if (sdd->cur_mode & SPI_CPHA)
+ val |= S3C64XX_SPI_CPHA_B;
+
+ writel(val, regs + S3C64XX_SPI_CH_CFG);
+
+ /* Set Channel & DMA Mode */
+ val = readl(regs + S3C64XX_SPI_MODE_CFG);
+ val &= ~(S3C64XX_SPI_MODE_BUS_TSZ_MASK
+ | S3C64XX_SPI_MODE_CH_TSZ_MASK);
+
+ switch (sdd->cur_bpw) {
+ case 32:
+ val |= S3C64XX_SPI_MODE_BUS_TSZ_WORD;
+ break;
+ case 16:
+ val |= S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD;
+ break;
+ default:
+ val |= S3C64XX_SPI_MODE_BUS_TSZ_BYTE;
+ break;
+ }
+ val |= S3C64XX_SPI_MODE_CH_TSZ_BYTE; /* Always 8bits wide */
+
+ writel(val, regs + S3C64XX_SPI_MODE_CFG);
+
+ /* Configure Clock */
+ val = readl(regs + S3C64XX_SPI_CLK_CFG);
+ val &= ~S3C64XX_SPI_PSR_MASK;
+ val |= ((clk_get_rate(sci->src_clk) / sdd->cur_speed / 2 - 1)
+ & S3C64XX_SPI_PSR_MASK);
+ writel(val, regs + S3C64XX_SPI_CLK_CFG);
+
+ /* Enable Clock */
+ val = readl(regs + S3C64XX_SPI_CLK_CFG);
+ val |= S3C64XX_SPI_ENCLK_ENABLE;
+ writel(val, regs + S3C64XX_SPI_CLK_CFG);
+}
+
+void s3c64xx_spi_dma_rxcb(struct s3c2410_dma_chan *chan, void *buf_id,
+ int size, enum s3c2410_dma_buffresult res)
+{
+ struct s3c64xx_spi_driver_data *sdd = buf_id;
+ unsigned long flags;
+
+ spin_lock_irqsave(&sdd->lock, flags);
+
+ if (res == S3C2410_RES_OK)
+ sdd->state &= ~RXBUSY;
+ else
+ dev_err(&sdd->pdev->dev, "DmaAbrtRx-%d\n", size);
+
+ /* If the other done */
+ if (!(sdd->state & TXBUSY))
+ complete(&sdd->xfer_completion);
+
+ spin_unlock_irqrestore(&sdd->lock, flags);
+}
+
+void s3c64xx_spi_dma_txcb(struct s3c2410_dma_chan *chan, void *buf_id,
+ int size, enum s3c2410_dma_buffresult res)
+{
+ struct s3c64xx_spi_driver_data *sdd = buf_id;
+ unsigned long flags;
+
+ spin_lock_irqsave(&sdd->lock, flags);
+
+ if (res == S3C2410_RES_OK)
+ sdd->state &= ~TXBUSY;
+ else
+ dev_err(&sdd->pdev->dev, "DmaAbrtTx-%d \n", size);
+
+ /* If the other done */
+ if (!(sdd->state & RXBUSY))
+ complete(&sdd->xfer_completion);
+
+ spin_unlock_irqrestore(&sdd->lock, flags);
+}
+
+#define XFER_DMAADDR_INVALID DMA_BIT_MASK(32)
+
+static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd,
+ struct spi_message *msg)
+{
+ struct device *dev = &sdd->pdev->dev;
+ struct spi_transfer *xfer;
+
+ if (msg->is_dma_mapped)
+ return 0;
+
+ /* First mark all xfer unmapped */
+ list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+ xfer->rx_dma = XFER_DMAADDR_INVALID;
+ xfer->tx_dma = XFER_DMAADDR_INVALID;
+ }
+
+ /* Map until end or first fail */
+ list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+
+ if (xfer->tx_buf != NULL) {
+ xfer->tx_dma = dma_map_single(dev, xfer->tx_buf,
+ xfer->len, DMA_TO_DEVICE);
+ if (dma_mapping_error(dev, xfer->tx_dma)) {
+ dev_err(dev, "dma_map_single Tx failed\n");
+ xfer->tx_dma = XFER_DMAADDR_INVALID;
+ return -ENOMEM;
+ }
+ }
+
+ if (xfer->rx_buf != NULL) {
+ xfer->rx_dma = dma_map_single(dev, xfer->rx_buf,
+ xfer->len, DMA_FROM_DEVICE);
+ if (dma_mapping_error(dev, xfer->rx_dma)) {
+ dev_err(dev, "dma_map_single Rx failed\n");
+ dma_unmap_single(dev, xfer->tx_dma,
+ xfer->len, DMA_TO_DEVICE);
+ xfer->tx_dma = XFER_DMAADDR_INVALID;
+ xfer->rx_dma = XFER_DMAADDR_INVALID;
+ return -ENOMEM;
+ }
+ }
+ }
+
+ return 0;
+}
+
+static void s3c64xx_spi_unmap_mssg(struct s3c64xx_spi_driver_data *sdd,
+ struct spi_message *msg)
+{
+ struct device *dev = &sdd->pdev->dev;
+ struct spi_transfer *xfer;
+
+ if (msg->is_dma_mapped)
+ return;
+
+ list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+
+ if (xfer->rx_buf != NULL
+ && xfer->rx_dma != XFER_DMAADDR_INVALID)
+ dma_unmap_single(dev, xfer->rx_dma,
+ xfer->len, DMA_FROM_DEVICE);
+
+ if (xfer->tx_buf != NULL
+ && xfer->tx_dma != XFER_DMAADDR_INVALID)
+ dma_unmap_single(dev, xfer->tx_dma,
+ xfer->len, DMA_TO_DEVICE);
+ }
+}
+
+static void handle_msg(struct s3c64xx_spi_driver_data *sdd,
+ struct spi_message *msg)
+{
+ struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+ struct spi_device *spi = msg->spi;
+ struct s3c64xx_spi_csinfo *cs = spi->controller_data;
+ struct spi_transfer *xfer;
+ int status = 0, cs_toggle = 0;
+ u32 speed;
+ u8 bpw;
+
+ /* If Master's(controller) state differs from that needed by Slave */
+ if (sdd->cur_speed != spi->max_speed_hz
+ || sdd->cur_mode != spi->mode
+ || sdd->cur_bpw != spi->bits_per_word) {
+ sdd->cur_bpw = spi->bits_per_word;
+ sdd->cur_speed = spi->max_speed_hz;
+ sdd->cur_mode = spi->mode;
+ s3c64xx_spi_config(sdd);
+ }
+
+ /* Map all the transfers if needed */
+ if (s3c64xx_spi_map_mssg(sdd, msg)) {
+ dev_err(&spi->dev,
+ "Xfer: Unable to map message buffers!\n");
+ status = -ENOMEM;
+ goto out;
+ }
+
+ /* Configure feedback delay */
+ writel(cs->fb_delay & 0x3, sdd->regs + S3C64XX_SPI_FB_CLK);
+
+ list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+
+ unsigned long flags;
+ int use_dma;
+
+ INIT_COMPLETION(sdd->xfer_completion);
+
+ /* Only BPW and Speed may change across transfers */
+ bpw = xfer->bits_per_word ? : spi->bits_per_word;
+ speed = xfer->speed_hz ? : spi->max_speed_hz;
+
+ if (bpw != sdd->cur_bpw || speed != sdd->cur_speed) {
+ sdd->cur_bpw = bpw;
+ sdd->cur_speed = speed;
+ s3c64xx_spi_config(sdd);
+ }
+
+ /* Polling method for xfers not bigger than FIFO capacity */
+ if (xfer->len <= ((sci->fifo_lvl_mask >> 1) + 1))
+ use_dma = 0;
+ else
+ use_dma = 1;
+
+ spin_lock_irqsave(&sdd->lock, flags);
+
+ /* Pending only which is to be done */
+ sdd->state &= ~RXBUSY;
+ sdd->state &= ~TXBUSY;
+
+ enable_datapath(sdd, spi, xfer, use_dma);
+
+ /* Slave Select */
+ enable_cs(sdd, spi);
+
+ /* Start the signals */
+ S3C64XX_SPI_ACT(sdd);
+
+ spin_unlock_irqrestore(&sdd->lock, flags);
+
+ status = wait_for_xfer(sdd, xfer, use_dma);
+
+ /* Quiese the signals */
+ S3C64XX_SPI_DEACT(sdd);
+
+ if (status) {
+ dev_err(&spi->dev, "I/O Error: \
+ rx-%d tx-%d res:rx-%c tx-%c len-%d\n",
+ xfer->rx_buf ? 1 : 0, xfer->tx_buf ? 1 : 0,
+ (sdd->state & RXBUSY) ? 'f' : 'p',
+ (sdd->state & TXBUSY) ? 'f' : 'p',
+ xfer->len);
+
+ if (use_dma) {
+ if (xfer->tx_buf != NULL
+ && (sdd->state & TXBUSY))
+ s3c2410_dma_ctrl(sdd->tx_dmach,
+ S3C2410_DMAOP_FLUSH);
+ if (xfer->rx_buf != NULL
+ && (sdd->state & RXBUSY))
+ s3c2410_dma_ctrl(sdd->rx_dmach,
+ S3C2410_DMAOP_FLUSH);
+ }
+
+ goto out;
+ }
+
+ if (xfer->delay_usecs)
+ udelay(xfer->delay_usecs);
+
+ if (xfer->cs_change) {
+ /* Hint that the next mssg is gonna be
+ for the same device */
+ if (list_is_last(&xfer->transfer_list,
+ &msg->transfers))
+ cs_toggle = 1;
+ else
+ disable_cs(sdd, spi);
+ }
+
+ msg->actual_length += xfer->len;
+
+ flush_fifo(sdd);
+ }
+
+out:
+ if (!cs_toggle || status)
+ disable_cs(sdd, spi);
+ else
+ sdd->tgl_spi = spi;
+
+ s3c64xx_spi_unmap_mssg(sdd, msg);
+
+ msg->status = status;
+
+ if (msg->complete)
+ msg->complete(msg->context);
+}
+
+static int acquire_dma(struct s3c64xx_spi_driver_data *sdd)
+{
+ if (s3c2410_dma_request(sdd->rx_dmach,
+ &s3c64xx_spi_dma_client, NULL) < 0) {
+ dev_err(&sdd->pdev->dev, "cannot get RxDMA\n");
+ return 0;
+ }
+ s3c2410_dma_set_buffdone_fn(sdd->rx_dmach, s3c64xx_spi_dma_rxcb);
+ s3c2410_dma_devconfig(sdd->rx_dmach, S3C2410_DMASRC_HW,
+ sdd->sfr_start + S3C64XX_SPI_RX_DATA);
+
+ if (s3c2410_dma_request(sdd->tx_dmach,
+ &s3c64xx_spi_dma_client, NULL) < 0) {
+ dev_err(&sdd->pdev->dev, "cannot get TxDMA\n");
+ s3c2410_dma_free(sdd->rx_dmach, &s3c64xx_spi_dma_client);
+ return 0;
+ }
+ s3c2410_dma_set_buffdone_fn(sdd->tx_dmach, s3c64xx_spi_dma_txcb);
+ s3c2410_dma_devconfig(sdd->tx_dmach, S3C2410_DMASRC_MEM,
+ sdd->sfr_start + S3C64XX_SPI_TX_DATA);
+
+ return 1;
+}
+
+static void s3c64xx_spi_work(struct work_struct *work)
+{
+ struct s3c64xx_spi_driver_data *sdd = container_of(work,
+ struct s3c64xx_spi_driver_data, work);
+ unsigned long flags;
+
+ /* Acquire DMA channels */
+ while (!acquire_dma(sdd))
+ msleep(10);
+
+ spin_lock_irqsave(&sdd->lock, flags);
+
+ while (!list_empty(&sdd->queue)
+ && !(sdd->state & SUSPND)) {
+
+ struct spi_message *msg;
+
+ msg = container_of(sdd->queue.next, struct spi_message, queue);
+
+ list_del_init(&msg->queue);
+
+ /* Set Xfer busy flag */
+ sdd->state |= SPIBUSY;
+
+ spin_unlock_irqrestore(&sdd->lock, flags);
+
+ handle_msg(sdd, msg);
+
+ spin_lock_irqsave(&sdd->lock, flags);
+
+ sdd->state &= ~SPIBUSY;
+ }
+
+ spin_unlock_irqrestore(&sdd->lock, flags);
+
+ /* Free DMA channels */
+ s3c2410_dma_free(sdd->tx_dmach, &s3c64xx_spi_dma_client);
+ s3c2410_dma_free(sdd->rx_dmach, &s3c64xx_spi_dma_client);
+}
+
+static int s3c64xx_spi_transfer(struct spi_device *spi,
+ struct spi_message *msg)
+{
+ struct s3c64xx_spi_driver_data *sdd;
+ unsigned long flags;
+
+ sdd = spi_master_get_devdata(spi->master);
+
+ spin_lock_irqsave(&sdd->lock, flags);
+
+ if (sdd->state & SUSPND) {
+ spin_unlock_irqrestore(&sdd->lock, flags);
+ return -ESHUTDOWN;
+ }
+
+ msg->status = -EINPROGRESS;
+ msg->actual_length = 0;
+
+ list_add_tail(&msg->queue, &sdd->queue);
+
+ queue_work(sdd->workqueue, &sdd->work);
+
+ spin_unlock_irqrestore(&sdd->lock, flags);
+
+ return 0;
+}
+
+/*
+ * Here we only check the validity of requested configuration
+ * and save the configuration in a local data-structure.
+ * The controller is actually configured only just before we
+ * get a message to transfer.
+ */
+static int s3c64xx_spi_setup(struct spi_device *spi)
+{
+ struct s3c64xx_spi_csinfo *cs = spi->controller_data;
+ struct s3c64xx_spi_driver_data *sdd;
+ struct s3c64xx_spi_cntrlr_info *sci;
+ struct spi_message *msg;
+ u32 psr, speed;
+ unsigned long flags;
+ int err = 0;
+
+ if (cs == NULL || cs->set_level == NULL) {
+ dev_err(&spi->dev, "No CS for SPI(%d)\n", spi->chip_select);
+ return -ENODEV;
+ }
+
+ sdd = spi_master_get_devdata(spi->master);
+ sci = sdd->cntrlr_info;
+
+ spin_lock_irqsave(&sdd->lock, flags);
+
+ list_for_each_entry(msg, &sdd->queue, queue) {
+ /* Is some mssg is already queued for this device */
+ if (msg->spi == spi) {
+ dev_err(&spi->dev,
+ "setup: attempt while mssg in queue!\n");
+ spin_unlock_irqrestore(&sdd->lock, flags);
+ return -EBUSY;
+ }
+ }
+
+ if (sdd->state & SUSPND) {
+ spin_unlock_irqrestore(&sdd->lock, flags);
+ dev_err(&spi->dev,
+ "setup: SPI-%d not active!\n", spi->master->bus_num);
+ return -ESHUTDOWN;
+ }
+
+ spin_unlock_irqrestore(&sdd->lock, flags);
+
+ if (spi->bits_per_word != 8
+ && spi->bits_per_word != 16
+ && spi->bits_per_word != 32) {
+ dev_err(&spi->dev, "setup: %dbits/wrd not supported!\n",
+ spi->bits_per_word);
+ err = -EINVAL;
+ goto setup_exit;
+ }
+
+ /* Check if we can provide the requested rate */
+ speed = clk_get_rate(sci->src_clk) / 2 / (0 + 1); /* Max possible */
+
+ if (spi->max_speed_hz > speed)
+ spi->max_speed_hz = speed;
+
+ psr = clk_get_rate(sci->src_clk) / 2 / spi->max_speed_hz - 1;
+ psr &= S3C64XX_SPI_PSR_MASK;
+ if (psr == S3C64XX_SPI_PSR_MASK)
+ psr--;
+
+ speed = clk_get_rate(sci->src_clk) / 2 / (psr + 1);
+ if (spi->max_speed_hz < speed) {
+ if (psr+1 < S3C64XX_SPI_PSR_MASK) {
+ psr++;
+ } else {
+ err = -EINVAL;
+ goto setup_exit;
+ }
+ }
+
+ speed = clk_get_rate(sci->src_clk) / 2 / (psr + 1);
+ if (spi->max_speed_hz >= speed)
+ spi->max_speed_hz = speed;
+ else
+ err = -EINVAL;
+
+setup_exit:
+
+ /* setup() returns with device de-selected */
+ disable_cs(sdd, spi);
+
+ return err;
+}
+
+static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd, int channel)
+{
+ struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+ void __iomem *regs = sdd->regs;
+ unsigned int val;
+
+ sdd->cur_speed = 0;
+
+ S3C64XX_SPI_DEACT(sdd);
+
+ /* Disable Interrupts - we use Polling if not DMA mode */
+ writel(0, regs + S3C64XX_SPI_INT_EN);
+
+ writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT,
+ regs + S3C64XX_SPI_CLK_CFG);
+ writel(0, regs + S3C64XX_SPI_MODE_CFG);
+ writel(0, regs + S3C64XX_SPI_PACKET_CNT);
+
+ /* Clear any irq pending bits */
+ writel(readl(regs + S3C64XX_SPI_PENDING_CLR),
+ regs + S3C64XX_SPI_PENDING_CLR);
+
+ writel(0, regs + S3C64XX_SPI_SWAP_CFG);
+
+ val = readl(regs + S3C64XX_SPI_MODE_CFG);
+ val &= ~S3C64XX_SPI_MODE_4BURST;
+ val &= ~(S3C64XX_SPI_MAX_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF);
+ val |= (S3C64XX_SPI_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF);
+ writel(val, regs + S3C64XX_SPI_MODE_CFG);
+
+ flush_fifo(sdd);
+}
+
+static int __init s3c64xx_spi_probe(struct platform_device *pdev)
+{
+ struct resource *mem_res, *dmatx_res, *dmarx_res;
+ struct s3c64xx_spi_driver_data *sdd;
+ struct s3c64xx_spi_cntrlr_info *sci;
+ struct spi_master *master;
+ int ret;
+
+ if (pdev->id < 0) {
+ dev_err(&pdev->dev,
+ "Invalid platform device id-%d\n", pdev->id);
+ return -ENODEV;
+ }
+
+ if (pdev->dev.platform_data == NULL) {
+ dev_err(&pdev->dev, "platform_data missing!\n");
+ return -ENODEV;
+ }
+
+ /* Check for availability of necessary resource */
+
+ dmatx_res = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+ if (dmatx_res == NULL) {
+ dev_err(&pdev->dev, "Unable to get SPI-Tx dma resource\n");
+ return -ENXIO;
+ }
+
+ dmarx_res = platform_get_resource(pdev, IORESOURCE_DMA, 1);
+ if (dmarx_res == NULL) {
+ dev_err(&pdev->dev, "Unable to get SPI-Rx dma resource\n");
+ return -ENXIO;
+ }
+
+ mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (mem_res == NULL) {
+ dev_err(&pdev->dev, "Unable to get SPI MEM resource\n");
+ return -ENXIO;
+ }
+
+ master = spi_alloc_master(&pdev->dev,
+ sizeof(struct s3c64xx_spi_driver_data));
+ if (master == NULL) {
+ dev_err(&pdev->dev, "Unable to allocate SPI Master\n");
+ return -ENOMEM;
+ }
+
+ sci = pdev->dev.platform_data;
+
+ platform_set_drvdata(pdev, master);
+
+ sdd = spi_master_get_devdata(master);
+ sdd->master = master;
+ sdd->cntrlr_info = sci;
+ sdd->pdev = pdev;
+ sdd->sfr_start = mem_res->start;
+ sdd->tx_dmach = dmatx_res->start;
+ sdd->rx_dmach = dmarx_res->start;
+
+ sdd->cur_bpw = 8;
+
+ master->bus_num = pdev->id;
+ master->setup = s3c64xx_spi_setup;
+ master->transfer = s3c64xx_spi_transfer;
+ master->num_chipselect = sci->num_cs;
+ master->dma_alignment = 8;
+ /* the spi->mode bits understood by this driver: */
+ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+
+ if (request_mem_region(mem_res->start,
+ resource_size(mem_res), pdev->name) == NULL) {
+ dev_err(&pdev->dev, "Req mem region failed\n");
+ ret = -ENXIO;
+ goto err0;
+ }
+
+ sdd->regs = ioremap(mem_res->start, resource_size(mem_res));
+ if (sdd->regs == NULL) {
+ dev_err(&pdev->dev, "Unable to remap IO\n");
+ ret = -ENXIO;
+ goto err1;
+ }
+
+ if (sci->cfg_gpio == NULL || sci->cfg_gpio(pdev)) {
+ dev_err(&pdev->dev, "Unable to config gpio\n");
+ ret = -EBUSY;
+ goto err2;
+ }
+
+ /* Setup clocks */
+ sdd->clk = clk_get(&pdev->dev, "spi");
+ if (IS_ERR(sdd->clk)) {
+ dev_err(&pdev->dev, "Unable to acquire clock 'spi'\n");
+ ret = PTR_ERR(sdd->clk);
+ goto err3;
+ }
+
+ if (clk_enable(sdd->clk)) {
+ dev_err(&pdev->dev, "Couldn't enable clock 'spi'\n");
+ ret = -EBUSY;
+ goto err4;
+ }
+
+ if (sci->src_clk_nr == S3C64XX_SPI_SRCCLK_PCLK)
+ sci->src_clk = sdd->clk;
+ else
+ sci->src_clk = clk_get(&pdev->dev, sci->src_clk_name);
+ if (IS_ERR(sci->src_clk)) {
+ dev_err(&pdev->dev,
+ "Unable to acquire clock '%s'\n", sci->src_clk_name);
+ ret = PTR_ERR(sci->src_clk);
+ goto err5;
+ }
+
+ if (sci->src_clk != sdd->clk && clk_enable(sci->src_clk)) {
+ dev_err(&pdev->dev, "Couldn't enable clock '%s'\n",
+ sci->src_clk_name);
+ ret = -EBUSY;
+ goto err6;
+ }
+
+ sdd->workqueue = create_singlethread_workqueue(
+ dev_name(master->dev.parent));
+ if (sdd->workqueue == NULL) {
+ dev_err(&pdev->dev, "Unable to create workqueue\n");
+ ret = -ENOMEM;
+ goto err7;
+ }
+
+ /* Setup Deufult Mode */
+ s3c64xx_spi_hwinit(sdd, pdev->id);
+
+ spin_lock_init(&sdd->lock);
+ init_completion(&sdd->xfer_completion);
+ INIT_WORK(&sdd->work, s3c64xx_spi_work);
+ INIT_LIST_HEAD(&sdd->queue);
+
+ if (spi_register_master(master)) {
+ dev_err(&pdev->dev, "cannot register SPI master\n");
+ ret = -EBUSY;
+ goto err8;
+ }
+
+ dev_dbg(&pdev->dev, "Samsung SoC SPI Driver loaded for Bus SPI-%d \
+ with %d Slaves attached\n",
+ pdev->id, master->num_chipselect);
+ dev_dbg(&pdev->dev, "\tIOmem=[0x%x-0x%x]\
+ \tDMA=[Rx-%d, Tx-%d]\n",
+ mem_res->end, mem_res->start,
+ sdd->rx_dmach, sdd->tx_dmach);
+
+ return 0;
+
+err8:
+ destroy_workqueue(sdd->workqueue);
+err7:
+ if (sci->src_clk != sdd->clk)
+ clk_disable(sci->src_clk);
+err6:
+ if (sci->src_clk != sdd->clk)
+ clk_put(sci->src_clk);
+err5:
+ clk_disable(sdd->clk);
+err4:
+ clk_put(sdd->clk);
+err3:
+err2:
+ iounmap((void *) sdd->regs);
+err1:
+ release_mem_region(mem_res->start, resource_size(mem_res));
+err0:
+ platform_set_drvdata(pdev, NULL);
+ spi_master_put(master);
+
+ return ret;
+}
+
+static int s3c64xx_spi_remove(struct platform_device *pdev)
+{
+ struct spi_master *master = spi_master_get(platform_get_drvdata(pdev));
+ struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
+ struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+ struct resource *mem_res;
+ unsigned long flags;
+
+ spin_lock_irqsave(&sdd->lock, flags);
+ sdd->state |= SUSPND;
+ spin_unlock_irqrestore(&sdd->lock, flags);
+
+ while (sdd->state & SPIBUSY)
+ msleep(10);
+
+ spi_unregister_master(master);
+
+ destroy_workqueue(sdd->workqueue);
+
+ if (sci->src_clk != sdd->clk)
+ clk_disable(sci->src_clk);
+
+ if (sci->src_clk != sdd->clk)
+ clk_put(sci->src_clk);
+
+ clk_disable(sdd->clk);
+ clk_put(sdd->clk);
+
+ iounmap((void *) sdd->regs);
+
+ mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ release_mem_region(mem_res->start, resource_size(mem_res));
+
+ platform_set_drvdata(pdev, NULL);
+ spi_master_put(master);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int s3c64xx_spi_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct spi_master *master = spi_master_get(platform_get_drvdata(pdev));
+ struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
+ struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+ struct s3c64xx_spi_csinfo *cs;
+ unsigned long flags;
+
+ spin_lock_irqsave(&sdd->lock, flags);
+ sdd->state |= SUSPND;
+ spin_unlock_irqrestore(&sdd->lock, flags);
+
+ while (sdd->state & SPIBUSY)
+ msleep(10);
+
+ /* Disable the clock */
+ if (sci->src_clk != sdd->clk)
+ clk_disable(sci->src_clk);
+
+ clk_disable(sdd->clk);
+
+ sdd->cur_speed = 0; /* Output Clock is stopped */
+
+ return 0;
+}
+
+static int s3c64xx_spi_resume(struct platform_device *pdev)
+{
+ struct spi_master *master = spi_master_get(platform_get_drvdata(pdev));
+ struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
+ struct s3c64xx_spi_cntrlr_info *sci = sdd->cntrlr_info;
+ unsigned long flags;
+
+ sci->cfg_gpio(pdev);
+
+ /* Enable the clock */
+ if (sci->src_clk != sdd->clk)
+ clk_enable(sci->src_clk);
+
+ clk_enable(sdd->clk);
+
+ s3c64xx_spi_hwinit(sdd, pdev->id);
+
+ spin_lock_irqsave(&sdd->lock, flags);
+ sdd->state &= ~SUSPND;
+ spin_unlock_irqrestore(&sdd->lock, flags);
+
+ return 0;
+}
+#else
+#define s3c64xx_spi_suspend NULL
+#define s3c64xx_spi_resume NULL
+#endif /* CONFIG_PM */
+
+static struct platform_driver s3c64xx_spi_driver = {
+ .driver = {
+ .name = "s3c64xx-spi",
+ .owner = THIS_MODULE,
+ },
+ .remove = s3c64xx_spi_remove,
+ .suspend = s3c64xx_spi_suspend,
+ .resume = s3c64xx_spi_resume,
+};
+MODULE_ALIAS("platform:s3c64xx-spi");
+
+static int __init s3c64xx_spi_init(void)
+{
+ return platform_driver_probe(&s3c64xx_spi_driver, s3c64xx_spi_probe);
+}
+module_init(s3c64xx_spi_init);
+
+static void __exit s3c64xx_spi_exit(void)
+{
+ platform_driver_unregister(&s3c64xx_spi_driver);
+}
+module_exit(s3c64xx_spi_exit);
+
+MODULE_AUTHOR("Jaswinder Singh <jassi.brar@samsung.com>");
+MODULE_DESCRIPTION("S3C64XX SPI Controller Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/spi/spi_sh_sci.c b/drivers/spi/spi_sh_sci.c
index 7d36720eb982..a65c12ffa733 100644
--- a/drivers/spi/spi_sh_sci.c
+++ b/drivers/spi/spi_sh_sci.c
@@ -148,7 +148,7 @@ static int sh_sci_spi_probe(struct platform_device *dev)
ret = -ENOENT;
goto err1;
}
- sp->membase = ioremap(r->start, r->end - r->start + 1);
+ sp->membase = ioremap(r->start, resource_size(r));
if (!sp->membase) {
ret = -ENXIO;
goto err1;
diff --git a/drivers/spi/spi_txx9.c b/drivers/spi/spi_txx9.c
index 19f75627c3de..dfa024b633e1 100644
--- a/drivers/spi/spi_txx9.c
+++ b/drivers/spi/spi_txx9.c
@@ -375,12 +375,10 @@ static int __init txx9spi_probe(struct platform_device *dev)
res = platform_get_resource(dev, IORESOURCE_MEM, 0);
if (!res)
goto exit_busy;
- if (!devm_request_mem_region(&dev->dev,
- res->start, res->end - res->start + 1,
+ if (!devm_request_mem_region(&dev->dev, res->start, resource_size(res),
"spi_txx9"))
goto exit_busy;
- c->membase = devm_ioremap(&dev->dev,
- res->start, res->end - res->start + 1);
+ c->membase = devm_ioremap(&dev->dev, res->start, resource_size(res));
if (!c->membase)
goto exit_busy;
diff --git a/drivers/spi/spidev.c b/drivers/spi/spidev.c
index 9c446e6003d5..ea1bec3c9a13 100644
--- a/drivers/spi/spidev.c
+++ b/drivers/spi/spidev.c
@@ -53,7 +53,7 @@
#define SPIDEV_MAJOR 153 /* assigned */
#define N_SPI_MINORS 32 /* ... up to 256 */
-static unsigned long minors[N_SPI_MINORS / BITS_PER_LONG];
+static DECLARE_BITMAP(minors, N_SPI_MINORS);
/* Bit masks for spi_device.mode management. Note that incorrect
@@ -558,7 +558,7 @@ static struct class *spidev_class;
/*-------------------------------------------------------------------------*/
-static int spidev_probe(struct spi_device *spi)
+static int __devinit spidev_probe(struct spi_device *spi)
{
struct spidev_data *spidev;
int status;
@@ -607,7 +607,7 @@ static int spidev_probe(struct spi_device *spi)
return status;
}
-static int spidev_remove(struct spi_device *spi)
+static int __devexit spidev_remove(struct spi_device *spi)
{
struct spidev_data *spidev = spi_get_drvdata(spi);
@@ -629,7 +629,7 @@ static int spidev_remove(struct spi_device *spi)
return 0;
}
-static struct spi_driver spidev_spi = {
+static struct spi_driver spidev_spi_driver = {
.driver = {
.name = "spidev",
.owner = THIS_MODULE,
@@ -661,14 +661,14 @@ static int __init spidev_init(void)
spidev_class = class_create(THIS_MODULE, "spidev");
if (IS_ERR(spidev_class)) {
- unregister_chrdev(SPIDEV_MAJOR, spidev_spi.driver.name);
+ unregister_chrdev(SPIDEV_MAJOR, spidev_spi_driver.driver.name);
return PTR_ERR(spidev_class);
}
- status = spi_register_driver(&spidev_spi);
+ status = spi_register_driver(&spidev_spi_driver);
if (status < 0) {
class_destroy(spidev_class);
- unregister_chrdev(SPIDEV_MAJOR, spidev_spi.driver.name);
+ unregister_chrdev(SPIDEV_MAJOR, spidev_spi_driver.driver.name);
}
return status;
}
@@ -676,9 +676,9 @@ module_init(spidev_init);
static void __exit spidev_exit(void)
{
- spi_unregister_driver(&spidev_spi);
+ spi_unregister_driver(&spidev_spi_driver);
class_destroy(spidev_class);
- unregister_chrdev(SPIDEV_MAJOR, spidev_spi.driver.name);
+ unregister_chrdev(SPIDEV_MAJOR, spidev_spi_driver.driver.name);
}
module_exit(spidev_exit);
diff --git a/include/linux/spi/dw_spi.h b/include/linux/spi/dw_spi.h
new file mode 100644
index 000000000000..51b3e771a9a3
--- /dev/null
+++ b/include/linux/spi/dw_spi.h
@@ -0,0 +1,212 @@
+#ifndef DW_SPI_HEADER_H
+#define DW_SPI_HEADER_H
+#include <linux/io.h>
+
+/* Bit fields in CTRLR0 */
+#define SPI_DFS_OFFSET 0
+
+#define SPI_FRF_OFFSET 4
+#define SPI_FRF_SPI 0x0
+#define SPI_FRF_SSP 0x1
+#define SPI_FRF_MICROWIRE 0x2
+#define SPI_FRF_RESV 0x3
+
+#define SPI_MODE_OFFSET 6
+#define SPI_SCPH_OFFSET 6
+#define SPI_SCOL_OFFSET 7
+#define SPI_TMOD_OFFSET 8
+#define SPI_TMOD_TR 0x0 /* xmit & recv */
+#define SPI_TMOD_TO 0x1 /* xmit only */
+#define SPI_TMOD_RO 0x2 /* recv only */
+#define SPI_TMOD_EPROMREAD 0x3 /* eeprom read mode */
+
+#define SPI_SLVOE_OFFSET 10
+#define SPI_SRL_OFFSET 11
+#define SPI_CFS_OFFSET 12
+
+/* Bit fields in SR, 7 bits */
+#define SR_MASK 0x7f /* cover 7 bits */
+#define SR_BUSY (1 << 0)
+#define SR_TF_NOT_FULL (1 << 1)
+#define SR_TF_EMPT (1 << 2)
+#define SR_RF_NOT_EMPT (1 << 3)
+#define SR_RF_FULL (1 << 4)
+#define SR_TX_ERR (1 << 5)
+#define SR_DCOL (1 << 6)
+
+/* Bit fields in ISR, IMR, RISR, 7 bits */
+#define SPI_INT_TXEI (1 << 0)
+#define SPI_INT_TXOI (1 << 1)
+#define SPI_INT_RXUI (1 << 2)
+#define SPI_INT_RXOI (1 << 3)
+#define SPI_INT_RXFI (1 << 4)
+#define SPI_INT_MSTI (1 << 5)
+
+/* TX RX interrupt level threshhold, max can be 256 */
+#define SPI_INT_THRESHOLD 32
+
+enum dw_ssi_type {
+ SSI_MOTO_SPI = 0,
+ SSI_TI_SSP,
+ SSI_NS_MICROWIRE,
+};
+
+struct dw_spi_reg {
+ u32 ctrl0;
+ u32 ctrl1;
+ u32 ssienr;
+ u32 mwcr;
+ u32 ser;
+ u32 baudr;
+ u32 txfltr;
+ u32 rxfltr;
+ u32 txflr;
+ u32 rxflr;
+ u32 sr;
+ u32 imr;
+ u32 isr;
+ u32 risr;
+ u32 txoicr;
+ u32 rxoicr;
+ u32 rxuicr;
+ u32 msticr;
+ u32 icr;
+ u32 dmacr;
+ u32 dmatdlr;
+ u32 dmardlr;
+ u32 idr;
+ u32 version;
+ u32 dr; /* Currently oper as 32 bits,
+ though only low 16 bits matters */
+} __packed;
+
+struct dw_spi {
+ struct spi_master *master;
+ struct spi_device *cur_dev;
+ struct device *parent_dev;
+ enum dw_ssi_type type;
+
+ void __iomem *regs;
+ unsigned long paddr;
+ u32 iolen;
+ int irq;
+ u32 max_freq; /* max bus freq supported */
+
+ u16 bus_num;
+ u16 num_cs; /* supported slave numbers */
+
+ /* Driver message queue */
+ struct workqueue_struct *workqueue;
+ struct work_struct pump_messages;
+ spinlock_t lock;
+ struct list_head queue;
+ int busy;
+ int run;
+
+ /* Message Transfer pump */
+ struct tasklet_struct pump_transfers;
+
+ /* Current message transfer state info */
+ struct spi_message *cur_msg;
+ struct spi_transfer *cur_transfer;
+ struct chip_data *cur_chip;
+ struct chip_data *prev_chip;
+ size_t len;
+ void *tx;
+ void *tx_end;
+ void *rx;
+ void *rx_end;
+ int dma_mapped;
+ dma_addr_t rx_dma;
+ dma_addr_t tx_dma;
+ size_t rx_map_len;
+ size_t tx_map_len;
+ u8 n_bytes; /* current is a 1/2 bytes op */
+ u8 max_bits_per_word; /* maxim is 16b */
+ u32 dma_width;
+ int cs_change;
+ int (*write)(struct dw_spi *dws);
+ int (*read)(struct dw_spi *dws);
+ irqreturn_t (*transfer_handler)(struct dw_spi *dws);
+ void (*cs_control)(u32 command);
+
+ /* Dma info */
+ int dma_inited;
+ struct dma_chan *txchan;
+ struct dma_chan *rxchan;
+ int txdma_done;
+ int rxdma_done;
+ u64 tx_param;
+ u64 rx_param;
+ struct device *dma_dev;
+ dma_addr_t dma_addr;
+
+ /* Bus interface info */
+ void *priv;
+#ifdef CONFIG_DEBUG_FS
+ struct dentry *debugfs;
+#endif
+};
+
+#define dw_readl(dw, name) \
+ __raw_readl(&(((struct dw_spi_reg *)dw->regs)->name))
+#define dw_writel(dw, name, val) \
+ __raw_writel((val), &(((struct dw_spi_reg *)dw->regs)->name))
+#define dw_readw(dw, name) \
+ __raw_readw(&(((struct dw_spi_reg *)dw->regs)->name))
+#define dw_writew(dw, name, val) \
+ __raw_writew((val), &(((struct dw_spi_reg *)dw->regs)->name))
+
+static inline void spi_enable_chip(struct dw_spi *dws, int enable)
+{
+ dw_writel(dws, ssienr, (enable ? 1 : 0));
+}
+
+static inline void spi_set_clk(struct dw_spi *dws, u16 div)
+{
+ dw_writel(dws, baudr, div);
+}
+
+static inline void spi_chip_sel(struct dw_spi *dws, u16 cs)
+{
+ if (cs > dws->num_cs)
+ return;
+ dw_writel(dws, ser, 1 << cs);
+}
+
+/* Disable IRQ bits */
+static inline void spi_mask_intr(struct dw_spi *dws, u32 mask)
+{
+ u32 new_mask;
+
+ new_mask = dw_readl(dws, imr) & ~mask;
+ dw_writel(dws, imr, new_mask);
+}
+
+/* Enable IRQ bits */
+static inline void spi_umask_intr(struct dw_spi *dws, u32 mask)
+{
+ u32 new_mask;
+
+ new_mask = dw_readl(dws, imr) | mask;
+ dw_writel(dws, imr, new_mask);
+}
+
+/*
+ * Each SPI slave device to work with dw_api controller should
+ * has such a structure claiming its working mode (PIO/DMA etc),
+ * which can be save in the "controller_data" member of the
+ * struct spi_device
+ */
+struct dw_spi_chip {
+ u8 poll_mode; /* 0 for contoller polling mode */
+ u8 type; /* SPI/SSP/Micrwire */
+ u8 enable_dma;
+ void (*cs_control)(u32 command);
+};
+
+extern int dw_spi_add_host(struct dw_spi *dws);
+extern void dw_spi_remove_host(struct dw_spi *dws);
+extern int dw_spi_suspend_host(struct dw_spi *dws);
+extern int dw_spi_resume_host(struct dw_spi *dws);
+#endif /* DW_SPI_HEADER_H */