diff options
| -rw-r--r-- | drivers/regulator/lp8788-ldo.c | 32 | ||||
| -rw-r--r-- | include/linux/mfd/lp8788.h | 16 |
2 files changed, 16 insertions, 32 deletions
diff --git a/drivers/regulator/lp8788-ldo.c b/drivers/regulator/lp8788-ldo.c index cbfd35873575..f2347474a106 100644 --- a/drivers/regulator/lp8788-ldo.c +++ b/drivers/regulator/lp8788-ldo.c @@ -16,7 +16,7 @@ #include <linux/err.h> #include <linux/platform_device.h> #include <linux/regulator/driver.h> -#include <linux/gpio.h> +#include <linux/gpio/consumer.h> #include <linux/mfd/lp8788.h> /* register address */ @@ -85,8 +85,6 @@ #define LP8788_STARTUP_TIME_S 3 #define ENABLE_TIME_USEC 32 -#define ENABLE GPIOF_OUT_INIT_HIGH -#define DISABLE GPIOF_OUT_INIT_LOW enum lp8788_ldo_id { DLDO1, @@ -117,7 +115,7 @@ struct lp8788_ldo { struct lp8788 *lp; struct regulator_desc *desc; struct regulator_dev *regulator; - struct lp8788_ldo_enable_pin *en_pin; + struct gpio_desc *ena_gpiod; }; /* DLDO 1, 2, 3, 9 voltage table */ @@ -469,7 +467,6 @@ static int lp8788_config_ldo_enable_mode(struct platform_device *pdev, enum lp8788_ldo_id id) { struct lp8788 *lp = ldo->lp; - struct lp8788_platform_data *pdata = lp->pdata; enum lp8788_ext_ldo_en_id enable_id; u8 en_mask[] = { [EN_ALDO1] = LP8788_EN_SEL_ALDO1_M, @@ -504,11 +501,18 @@ static int lp8788_config_ldo_enable_mode(struct platform_device *pdev, return 0; } - /* if no platform data for ldo pin, then set default enable mode */ - if (!pdata || !pdata->ldo_pin || !pdata->ldo_pin[enable_id]) + /* FIXME: check default mode for GPIO here: high or low? */ + ldo->ena_gpiod = devm_gpiod_get_index_optional(&pdev->dev, + "enable", + enable_id, + GPIOD_OUT_HIGH); + if (IS_ERR(ldo->ena_gpiod)) + return PTR_ERR(ldo->ena_gpiod); + + /* if no GPIO for ldo pin, then set default enable mode */ + if (!ldo->ena_gpiod) goto set_default_ldo_enable_mode; - ldo->en_pin = pdata->ldo_pin[enable_id]; return 0; set_default_ldo_enable_mode: @@ -533,10 +537,8 @@ static int lp8788_dldo_probe(struct platform_device *pdev) if (ret) return ret; - if (ldo->en_pin) { - cfg.ena_gpio = ldo->en_pin->gpio; - cfg.ena_gpio_flags = ldo->en_pin->init_state; - } + if (ldo->ena_gpiod) + cfg.ena_gpiod = ldo->ena_gpiod; cfg.dev = pdev->dev.parent; cfg.init_data = lp->pdata ? lp->pdata->dldo_data[id] : NULL; @@ -582,10 +584,8 @@ static int lp8788_aldo_probe(struct platform_device *pdev) if (ret) return ret; - if (ldo->en_pin) { - cfg.ena_gpio = ldo->en_pin->gpio; - cfg.ena_gpio_flags = ldo->en_pin->init_state; - } + if (ldo->ena_gpiod) + cfg.ena_gpiod = ldo->ena_gpiod; cfg.dev = pdev->dev.parent; cfg.init_data = lp->pdata ? lp->pdata->aldo_data[id] : NULL; diff --git a/include/linux/mfd/lp8788.h b/include/linux/mfd/lp8788.h index 786bf6679a28..2010e0de3e34 100644 --- a/include/linux/mfd/lp8788.h +++ b/include/linux/mfd/lp8788.h @@ -182,20 +182,6 @@ struct lp8788_buck2_dvs { }; /* - * struct lp8788_ldo_enable_pin - * - * Basically, all LDOs are enabled through the I2C commands. - * But ALDO 1 ~ 5, 7, DLDO 7, 9, 11 can be enabled by external gpio pins. - * - * @gpio : gpio number which is used for enabling ldos - * @init_state : initial gpio state (ex. GPIOF_OUT_INIT_LOW) - */ -struct lp8788_ldo_enable_pin { - int gpio; - int init_state; -}; - -/* * struct lp8788_chg_param * @addr : charging control register address (range : 0x11 ~ 0x1C) * @val : charging parameter value @@ -288,7 +274,6 @@ struct lp8788_vib_platform_data { * @aldo_data : regulator initial data for analog ldo * @buck1_dvs : gpio configurations for buck1 dvs * @buck2_dvs : gpio configurations for buck2 dvs - * @ldo_pin : gpio configurations for enabling LDOs * @chg_pdata : platform data for charger driver * @alarm_sel : rtc alarm selection (1 or 2) * @bl_pdata : configurable data for backlight driver @@ -306,7 +291,6 @@ struct lp8788_platform_data { struct regulator_init_data *aldo_data[LP8788_NUM_ALDOS]; struct lp8788_buck1_dvs *buck1_dvs; struct lp8788_buck2_dvs *buck2_dvs; - struct lp8788_ldo_enable_pin *ldo_pin[EN_LDOS_MAX]; /* charger */ struct lp8788_charger_platform_data *chg_pdata; |