diff options
| -rw-r--r-- | Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt | 104 |
1 files changed, 104 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt new file mode 100644 index 000000000000..b7b55a964f65 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt @@ -0,0 +1,104 @@ + Binding for Xilinx Zynq Pinctrl + +Required properties: +- compatible: "xlnx,zynq-pinctrl" +- syscon: phandle to SLCR +- reg: Offset and length of pinctrl space in SLCR + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Zynq's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, slew rate, etc. + +Each configuration node can consist of multiple nodes describing the pinmux and +pinconf options. Those nodes can be pinmux nodes or pinconf nodes. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Required properties for pinmux nodes are: + - groups: A list of pinmux groups. + - function: The name of a pinmux function to activate for the specified set + of groups. + +Required properties for configuration nodes: +One of: + - pins: a list of pin names + - groups: A list of pinmux groups. + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pinmux subnode: + groups, function + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pinconf subnode: + groups, pins, bias-disable, bias-high-impedance, bias-pull-up, slew-rate, + low-power-disable, low-power-enable + + Valid arguments for 'slew-rate' are '0' and '1' to select between slow and fast + respectively. + + Valid values for groups are: + ethernet0_0_grp, ethernet1_0_grp, mdio0_0_grp, mdio1_0_grp, + qspi0_0_grp, qspi1_0_grp, qspi_fbclk, qspi_cs1_grp, spi0_0_grp, + spi0_1_grp - spi0_2_grp, spi1_0_grp - spi1_3_grp, sdio0_0_grp - sdio0_2_grp, + sdio1_0_grp - sdio1_3_grp, sdio0_emio_wp, sdio0_emio_cd, sdio1_emio_wp, + sdio1_emio_cd, smc0_nor, smc0_nor_cs1_grp, smc0_nor_addr25_grp, smc0_nand, + can0_0_grp - can0_10_grp, can1_0_grp - can1_11_grp, uart0_0_grp - uart0_10_grp, + uart1_0_grp - uart1_11_grp, i2c0_0_grp - i2c0_10_grp, i2c1_0_grp - i2c1_10_grp, + ttc0_0_grp - ttc0_2_grp, ttc1_0_grp - ttc1_2_grp, swdt0_0_grp - swdt0_4_grp, + gpio0_0_grp - gpio0_53_grp, usb0_0_grp, usb1_0_grp + + Valid values for pins are: + MIO0 - MIO53 + + Valid values for function are: + ethernet0, ethernet1, mdio0, mdio1, qspi0, qspi1, qspi_fbclk, qspi_cs1, + spi0, spi1, sdio0, sdio0_pc, sdio0_cd, sdio0_wp, + sdio1, sdio1_pc, sdio1_cd, sdio1_wp, + smc0_nor, smc0_nor_cs1, smc0_nor_addr25, smc0_nand, can0, can1, uart0, uart1, + i2c0, i2c1, ttc0, ttc1, swdt0, gpio0, usb0, usb1 + +The following driver-specific properties as defined here are valid to specify in +a pin configuration subnode: + - io-standard: Configure the pin to use the selected IO standard according to + this mapping: + 1: LVCMOS18 + 2: LVCMOS25 + 3: LVCMOS33 + 4: HSTL + +Example: + pinctrl0: pinctrl@700 { + compatible = "xlnx,pinctrl-zynq"; + reg = <0x700 0x200>; + syscon = <&slcr>; + + pinctrl_uart1_default: uart1-default { + mux { + groups = "uart1_10_grp"; + function = "uart1"; + }; + + conf { + groups = "uart1_10_grp"; + slew-rate = <0>; + io-standard = <1>; + }; + + conf-rx { + pins = "MIO49"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO48"; + bias-disable; + }; + }; + }; |