summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--Documentation/networking/stmmac.txt24
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/common.h3
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/dwmac1000.h2
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c42
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c6
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h1
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/stmmac_main.c4
-rw-r--r--drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c3
-rw-r--r--include/linux/stmmac.h20
9 files changed, 89 insertions, 16 deletions
diff --git a/Documentation/networking/stmmac.txt b/Documentation/networking/stmmac.txt
index 61f40a3fa7ea..eacb640286b1 100644
--- a/Documentation/networking/stmmac.txt
+++ b/Documentation/networking/stmmac.txt
@@ -111,7 +111,7 @@ and detailed below as well:
int phy_addr;
int interface;
struct stmmac_mdio_bus_data *mdio_bus_data;
- int pbl;
+ struct stmmac_dma_cfg *dma_cfg;
int clk_csr;
int has_gmac;
int enh_desc;
@@ -163,7 +163,7 @@ Where:
o custom_cfg: this is a custom configuration that can be passed while
initialising the resources.
-The we have:
+For MDIO bus The we have:
struct stmmac_mdio_bus_data {
int bus_id;
@@ -180,10 +180,28 @@ Where:
o irqs: list of IRQs, one per PHY.
o probed_phy_irq: if irqs is NULL, use this for probed PHY.
+
+For DMA engine we have the following internal fields that should be
+tuned according to the HW capabilities.
+
+struct stmmac_dma_cfg {
+ int pbl;
+ int fixed_burst;
+ int burst_len_supported;
+};
+
+Where:
+ o pbl: Programmable Burst Length
+ o fixed_burst: program the DMA to use the fixed burst mode
+ o burst_len: this is the value we put in the register
+ supported values are provided as macros in
+ linux/stmmac.h header file.
+
+---
+
Below an example how the structures above are using on ST platforms.
static struct plat_stmmacenet_data stxYYY_ethernet_platform_data = {
- .pbl = 32,
.has_gmac = 0,
.enh_desc = 0,
.fix_mac_speed = stxYYY_ethernet_fix_mac_speed,
diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h
index eec8d34b6c88..b14829f8085d 100644
--- a/drivers/net/ethernet/stmicro/stmmac/common.h
+++ b/drivers/net/ethernet/stmicro/stmmac/common.h
@@ -236,7 +236,8 @@ struct stmmac_desc_ops {
struct stmmac_dma_ops {
/* DMA core initialization */
- int (*init) (void __iomem *ioaddr, int pbl, u32 dma_tx, u32 dma_rx);
+ int (*init) (void __iomem *ioaddr, int pbl, int fb, int burst_len,
+ u32 dma_tx, u32 dma_rx);
/* Dump DMA registers */
void (*dump_regs) (void __iomem *ioaddr);
/* Set tx/rx threshold in the csr6 register
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
index cfcef0ea0fa5..54339a78e358 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
@@ -142,7 +142,7 @@ enum rx_tx_priority_ratio {
#define DMA_BUS_MODE_RPBL_MASK 0x003e0000 /* Rx-Programmable Burst Len */
#define DMA_BUS_MODE_RPBL_SHIFT 17
#define DMA_BUS_MODE_USP 0x00800000
-#define DMA_BUS_MODE_4PBL 0x01000000
+#define DMA_BUS_MODE_PBL 0x01000000
#define DMA_BUS_MODE_AAL 0x02000000
/* DMA CRS Control and Status Register Mapping */
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
index 4d5402a1d262..3675c5731565 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
@@ -30,8 +30,8 @@
#include "dwmac1000.h"
#include "dwmac_dma.h"
-static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, u32 dma_tx,
- u32 dma_rx)
+static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb,
+ int burst_len, u32 dma_tx, u32 dma_rx)
{
u32 value = readl(ioaddr + DMA_BUS_MODE);
int limit;
@@ -48,15 +48,47 @@ static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, u32 dma_tx,
if (limit < 0)
return -EBUSY;
- value = /* DMA_BUS_MODE_FB | */ DMA_BUS_MODE_4PBL |
- ((pbl << DMA_BUS_MODE_PBL_SHIFT) |
- (pbl << DMA_BUS_MODE_RPBL_SHIFT));
+ /*
+ * Set the DMA PBL (Programmable Burst Length) mode
+ * Before stmmac core 3.50 this mode bit was 4xPBL, and
+ * post 3.5 mode bit acts as 8*PBL.
+ * For core rev < 3.5, when the core is set for 4xPBL mode, the
+ * DMA transfers the data in 4, 8, 16, 32, 64 & 128 beats
+ * depending on pbl value.
+ * For core rev > 3.5, when the core is set for 8xPBL mode, the
+ * DMA transfers the data in 8, 16, 32, 64, 128 & 256 beats
+ * depending on pbl value.
+ */
+ value = DMA_BUS_MODE_PBL | ((pbl << DMA_BUS_MODE_PBL_SHIFT) |
+ (pbl << DMA_BUS_MODE_RPBL_SHIFT));
+
+ /* Set the Fixed burst mode */
+ if (fb)
+ value |= DMA_BUS_MODE_FB;
#ifdef CONFIG_STMMAC_DA
value |= DMA_BUS_MODE_DA; /* Rx has priority over tx */
#endif
writel(value, ioaddr + DMA_BUS_MODE);
+ /* In case of GMAC AXI configuration, program the DMA_AXI_BUS_MODE
+ * for supported bursts.
+ *
+ * Note: This is applicable only for revision GMACv3.61a. For
+ * older version this register is reserved and shall have no
+ * effect.
+ *
+ * Note:
+ * For Fixed Burst Mode: if we directly write 0xFF to this
+ * register using the configurations pass from platform code,
+ * this would ensure that all bursts supported by core are set
+ * and those which are not supported would remain ineffective.
+ *
+ * For Non Fixed Burst Mode: provide the maximum value of the
+ * burst length. Any burst equal or below the provided burst
+ * length would be allowed to perform. */
+ writel(burst_len, ioaddr + DMA_AXI_BUS_MODE);
+
/* Mask interrupts by writing to CSR7 */
writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA);
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c
index bc17fd08b55d..92ed2e07609e 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c
@@ -32,8 +32,8 @@
#include "dwmac100.h"
#include "dwmac_dma.h"
-static int dwmac100_dma_init(void __iomem *ioaddr, int pbl, u32 dma_tx,
- u32 dma_rx)
+static int dwmac100_dma_init(void __iomem *ioaddr, int pbl, int fb,
+ int burst_len, u32 dma_tx, u32 dma_rx)
{
u32 value = readl(ioaddr + DMA_BUS_MODE);
int limit;
@@ -52,7 +52,7 @@ static int dwmac100_dma_init(void __iomem *ioaddr, int pbl, u32 dma_tx,
/* Enable Application Access by writing to DMA CSR0 */
writel(DMA_BUS_MODE_DEFAULT | (pbl << DMA_BUS_MODE_PBL_SHIFT),
- ioaddr + DMA_BUS_MODE);
+ ioaddr + DMA_BUS_MODE);
/* Mask interrupts by writing to CSR7 */
writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA);
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h b/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h
index 437edacd602e..6e0360f9cfde 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h
@@ -32,6 +32,7 @@
#define DMA_CONTROL 0x00001018 /* Ctrl (Operational Mode) */
#define DMA_INTR_ENA 0x0000101c /* Interrupt Enable */
#define DMA_MISSED_FRAME_CTR 0x00001020 /* Missed Frame Counter */
+#define DMA_AXI_BUS_MODE 0x00001028 /* AXI Bus Mode */
#define DMA_CUR_TX_BUF_ADDR 0x00001050 /* Current Host Tx Buffer */
#define DMA_CUR_RX_BUF_ADDR 0x00001054 /* Current Host Rx Buffer */
#define DMA_HW_FEATURE 0x00001058 /* HW Feature Register */
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 84f6b348ec70..933f63c4b2f3 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -944,7 +944,9 @@ static int stmmac_open(struct net_device *dev)
init_dma_desc_rings(dev);
/* DMA initialization and SW reset */
- ret = priv->hw->dma->init(priv->ioaddr, priv->plat->pbl,
+ ret = priv->hw->dma->init(priv->ioaddr, priv->plat->dma_cfg->pbl,
+ priv->plat->dma_cfg->fixed_burst,
+ priv->plat->dma_cfg->burst_len,
priv->dma_tx_phy, priv->dma_rx_phy);
if (ret < 0) {
pr_err("%s: DMA initialization failed\n", __func__);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
index da66ed7c3c5d..65e0f98520d6 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
@@ -35,7 +35,8 @@ static void stmmac_default_data(void)
plat_dat.bus_id = 1;
plat_dat.phy_addr = 0;
plat_dat.interface = PHY_INTERFACE_MODE_GMII;
- plat_dat.pbl = 32;
+ plat_dat.dma_cfg->pbl = 32;
+ plat_dat.dma_cfg->burst_len = DMA_AXI_BLEN_256;
plat_dat.clk_csr = 2; /* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
plat_dat.has_gmac = 1;
plat_dat.force_sf_dma_mode = 1;
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index e5292828b684..4aef9baff12b 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -60,6 +60,18 @@
* 1110 clk_csr_i/16
* 1111 clk_csr_i/18 */
+/* AXI DMA Burst length suported */
+#define DMA_AXI_BLEN_4 (1 << 1)
+#define DMA_AXI_BLEN_8 (1 << 2)
+#define DMA_AXI_BLEN_16 (1 << 3)
+#define DMA_AXI_BLEN_32 (1 << 4)
+#define DMA_AXI_BLEN_64 (1 << 5)
+#define DMA_AXI_BLEN_128 (1 << 6)
+#define DMA_AXI_BLEN_256 (1 << 7)
+#define DMA_AXI_BLEN_ALL (DMA_AXI_BLEN_4 | DMA_AXI_BLEN_8 | DMA_AXI_BLEN_16 \
+ | DMA_AXI_BLEN_32 | DMA_AXI_BLEN_64 \
+ | DMA_AXI_BLEN_128 | DMA_AXI_BLEN_256)
+
/* Platfrom data for platform device structure's platform_data field */
struct stmmac_mdio_bus_data {
@@ -70,13 +82,19 @@ struct stmmac_mdio_bus_data {
int probed_phy_irq;
};
+struct stmmac_dma_cfg {
+ int pbl;
+ int fixed_burst;
+ int burst_len;
+};
+
struct plat_stmmacenet_data {
char *phy_bus_name;
int bus_id;
int phy_addr;
int interface;
struct stmmac_mdio_bus_data *mdio_bus_data;
- int pbl;
+ struct stmmac_dma_cfg *dma_cfg;
int clk_csr;
int has_gmac;
int enh_desc;