diff options
33 files changed, 819 insertions, 254 deletions
diff --git a/Documentation/xtensa/mmu.txt b/Documentation/xtensa/mmu.txt new file mode 100644 index 000000000000..2b1af7606d57 --- /dev/null +++ b/Documentation/xtensa/mmu.txt @@ -0,0 +1,46 @@ +MMUv3 initialization sequence. + +The code in the initialize_mmu macro sets up MMUv3 memory mapping +identically to MMUv2 fixed memory mapping. Depending on +CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX symbol this code is +located in one of the following address ranges: + + 0xF0000000..0xFFFFFFFF (will keep same address in MMU v2 layout; + typically ROM) + 0x00000000..0x07FFFFFF (system RAM; this code is actually linked + at 0xD0000000..0xD7FFFFFF [cached] + or 0xD8000000..0xDFFFFFFF [uncached]; + in any case, initially runs elsewhere + than linked, so have to be careful) + +The code has the following assumptions: + This code fragment is run only on an MMU v3. + TLBs are in their reset state. + ITLBCFG and DTLBCFG are zero (reset state). + RASID is 0x04030201 (reset state). + PS.RING is zero (reset state). + LITBASE is zero (reset state, PC-relative literals); required to be PIC. + +TLB setup proceeds along the following steps. + + Legend: + VA = virtual address (two upper nibbles of it); + PA = physical address (two upper nibbles of it); + pc = physical range that contains this code; + +After step 2, we jump to virtual address in 0x40000000..0x5fffffff +that corresponds to next instruction to execute in this code. +After step 4, we jump to intended (linked) address of this code. + + Step 0 Step1 Step 2 Step3 Step 4 Step5 + ============ ===== ============ ===== ============ ===== + VA PA PA VA PA PA VA PA PA + ------ -- -- ------ -- -- ------ -- -- + E0..FF -> E0 -> E0 E0..FF -> E0 F0..FF -> F0 -> F0 + C0..DF -> C0 -> C0 C0..DF -> C0 E0..EF -> F0 -> F0 + A0..BF -> A0 -> A0 A0..BF -> A0 D8..DF -> 00 -> 00 + 80..9F -> 80 -> 80 80..9F -> 80 D0..D7 -> 00 -> 00 + 60..7F -> 60 -> 60 60..7F -> 60 + 40..5F -> 40 40..5F -> pc -> pc 40..5F -> pc + 20..3F -> 20 -> 20 20..3F -> 20 + 00..1F -> 00 -> 00 00..1F -> 00 diff --git a/arch/xtensa/Kconfig b/arch/xtensa/Kconfig index acdfc615cca2..0a1b95f81a32 100644 --- a/arch/xtensa/Kconfig +++ b/arch/xtensa/Kconfig @@ -1,11 +1,9 @@ -config FRAME_POINTER - def_bool n - config ZONE_DMA def_bool y config XTENSA def_bool y + select ARCH_WANT_FRAME_POINTERS select HAVE_IDE select GENERIC_ATOMIC64 select HAVE_GENERIC_HARDIRQS @@ -49,6 +47,15 @@ config HZ source "init/Kconfig" source "kernel/Kconfig.freezer" +config LOCKDEP_SUPPORT + def_bool y + +config STACKTRACE_SUPPORT + def_bool y + +config TRACE_IRQFLAGS_SUPPORT + def_bool y + config MMU def_bool n @@ -100,6 +107,35 @@ config MATH_EMULATION help Can we use information of configuration file? +config INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX + bool "Initialize Xtensa MMU inside the Linux kernel code" + default y + help + Earlier version initialized the MMU in the exception vector + before jumping to _startup in head.S and had an advantage that + it was possible to place a software breakpoint at 'reset' and + then enter your normal kernel breakpoints once the MMU was mapped + to the kernel mappings (0XC0000000). + + This unfortunately doesn't work for U-Boot and likley also wont + work for using KEXEC to have a hot kernel ready for doing a + KDUMP. + + So now the MMU is initialized in head.S but it's necessary to + use hardware breakpoints (gdb 'hbreak' cmd) to break at _startup. + xt-gdb can't place a Software Breakpoint in the 0XD region prior + to mapping the MMU and after mapping even if the area of low memory + was mapped gdb wouldn't remove the breakpoint on hitting it as the + PC wouldn't match. Since Hardware Breakpoints are recommended for + Linux configurations it seems reasonable to just assume they exist + and leave this older mechanism for unfortunate souls that choose + not to follow Tensilica's recommendation. + + Selecting this will cause U-Boot to set the KERNEL Load and Entry + address at 0x00003000 instead of the mapped std of 0xD0003000. + + If in doubt, say Y. + endmenu config XTENSA_CALIBRATE_CCOUNT @@ -249,21 +285,6 @@ endmenu menu "Executable file formats" -# only elf supported -config KCORE_ELF - def_bool y - depends on PROC_FS - help - If you enabled support for /proc file system then the file - /proc/kcore will contain the kernel core image in ELF format. This - can be used in gdb: - - $ cd /usr/src/linux ; gdb vmlinux /proc/kcore - - This is especially useful if you have compiled the kernel with the - "-g" option to preserve debugging information. It is mainly used - for examining kernel data structures on the live kernel. - source "fs/Kconfig.binfmt" endmenu diff --git a/arch/xtensa/boot/boot-elf/Makefile b/arch/xtensa/boot/boot-elf/Makefile index 1fe01b78c124..89db089f5a12 100644 --- a/arch/xtensa/boot/boot-elf/Makefile +++ b/arch/xtensa/boot/boot-elf/Makefile @@ -12,6 +12,7 @@ endif export OBJCOPY_ARGS export CPPFLAGS_boot.lds += -P -C +export KBUILD_AFLAGS += -mtext-section-literals boot-y := bootstrap.o diff --git a/arch/xtensa/boot/boot-elf/boot.lds.S b/arch/xtensa/boot/boot-elf/boot.lds.S index 7b646e0a6486..932b58ef33d4 100644 --- a/arch/xtensa/boot/boot-elf/boot.lds.S +++ b/arch/xtensa/boot/boot-elf/boot.lds.S @@ -1,41 +1,29 @@ -#include <variant/core.h> +/* + * linux/arch/xtensa/boot/boot-elf/boot.lds.S + * + * Copyright (C) 2008 - 2013 by Tensilica Inc. + * + * Chris Zankel <chris@zankel.net> + * Marc Gauthier <marc@tensilica.com + * Pete Delaney <piet@tensilica.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <asm/vectors.h> OUTPUT_ARCH(xtensa) ENTRY(_ResetVector) SECTIONS { - .start 0xD0000000 : { *(.start) } - - .text 0xD0000000: - { - __reloc_start = . ; - _text_start = . ; - *(.literal .text.literal .text) - _text_end = . ; - } - - .rodata ALIGN(0x04): - { - *(.rodata) - *(.rodata1) - } - - .data ALIGN(0x04): + .ResetVector.text XCHAL_RESET_VECTOR_VADDR : { - *(.data) - *(.data1) - *(.sdata) - *(.sdata2) - *(.got.plt) - *(.got) - *(.dynamic) + *(.ResetVector.text) } - __reloc_end = . ; - - . = ALIGN(0x10); - __image_load = . ; - .image 0xd0001000: + .image KERNELOFFSET: AT (LOAD_MEMORY_ADDRESS) { _image_start = .; *(image) @@ -43,7 +31,6 @@ SECTIONS _image_end = . ; } - .bss ((LOADADDR(.image) + SIZEOF(.image) + 3) & ~ 3): { __bss_start = .; @@ -53,14 +40,15 @@ SECTIONS *(.bss) __bss_end = .; } - _end = .; - _param_start = .; - .ResetVector.text XCHAL_RESET_VECTOR_VADDR : + /* + * This is a remapped copy of the Reset Vector Code. + * It keeps gdb in sync with the PC after switching + * to the temporary mapping used while setting up + * the V2 MMU mappings for Linux. + */ + .ResetVector.remapped_text 0x46000000 (INFO): { - *(.ResetVector.text) + *(.ResetVector.remapped_text) } - - - PROVIDE (end = .); } diff --git a/arch/xtensa/boot/boot-elf/bootstrap.S b/arch/xtensa/boot/boot-elf/bootstrap.S index 464298bc348b..1388a499753b 100644 --- a/arch/xtensa/boot/boot-elf/bootstrap.S +++ b/arch/xtensa/boot/boot-elf/bootstrap.S @@ -1,18 +1,77 @@ +/* + * arch/xtensa/boot/boot-elf/bootstrap.S + * + * Low-level exception handling + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright (C) 2004 - 2013 by Tensilica Inc. + * + * Chris Zankel <chris@zankel.net> + * Marc Gauthier <marc@tensilica.com> + * Piet Delaney <piet@tensilica.com> + */ #include <asm/bootparam.h> +#include <asm/processor.h> +#include <asm/pgtable.h> +#include <asm/page.h> +#include <asm/cacheasm.h> +#include <asm/initialize_mmu.h> +#include <linux/linkage.h> - -/* ResetVector - */ - .section .ResetVector.text, "ax" + .section .ResetVector.text, "ax" .global _ResetVector + .global reset + _ResetVector: - _j reset + _j _SetupMMU + + .begin no-absolute-literals + .literal_position + .align 4 RomInitAddr: - .word 0xd0001000 +#if defined(CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX) && \ + XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY + .word 0x00003000 +#else + .word 0xd0003000 +#endif RomBootParam: .word _bootparam +_bootparam: + .short BP_TAG_FIRST + .short 4 + .long BP_VERSION + .short BP_TAG_LAST + .short 0 + .long 0 + + .align 4 +_SetupMMU: + movi a0, 0 + wsr a0, windowbase + rsync + movi a0, 1 + wsr a0, windowstart + rsync + movi a0, 0x1F + wsr a0, ps + rsync + + Offset = _SetupMMU - _ResetVector + +#ifndef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX + initialize_mmu +#endif + + .end no-absolute-literals + + rsil a0, XCHAL_DEBUGLEVEL-1 + rsync reset: l32r a0, RomInitAddr l32r a2, RomBootParam @@ -21,13 +80,25 @@ reset: jx a0 .align 4 - .section .bootstrap.data, "aw" - .globl _bootparam -_bootparam: - .short BP_TAG_FIRST - .short 4 - .long BP_VERSION - .short BP_TAG_LAST - .short 0 - .long 0 + .section .ResetVector.remapped_text, "x" + .global _RemappedResetVector + + /* Do org before literals */ + .org 0 + +_RemappedResetVector: + .begin no-absolute-literals + .literal_position + + _j _RemappedSetupMMU + + /* Position Remapped code at the same location as the original code */ + . = _RemappedResetVector + Offset + +_RemappedSetupMMU: +#ifndef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX + initialize_mmu +#endif + + .end no-absolute-literals diff --git a/arch/xtensa/boot/boot-redboot/boot.ld b/arch/xtensa/boot/boot-redboot/boot.ld index 5bbcaf9e830d..b0b9e95b58bd 100644 --- a/arch/xtensa/boot/boot-redboot/boot.ld +++ b/arch/xtensa/boot/boot-redboot/boot.ld @@ -33,7 +33,7 @@ SECTIONS . = ALIGN(0x10); __image_load = . ; - .image 0xd0001000: AT(__image_load) + .image 0xd0003000: AT(__image_load) { _image_start = .; *(image) diff --git a/arch/xtensa/boot/boot-uboot/Makefile b/arch/xtensa/boot/boot-uboot/Makefile index bfbf8af582f1..545759819ef9 100644 --- a/arch/xtensa/boot/boot-uboot/Makefile +++ b/arch/xtensa/boot/boot-uboot/Makefile @@ -4,7 +4,11 @@ # for more details. # -UIMAGE_LOADADDR = 0xd0001000 +ifdef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX +UIMAGE_LOADADDR = 0x00003000 +else +UIMAGE_LOADADDR = 0xd0003000 +endif UIMAGE_COMPRESSION = gzip $(obj)/../uImage: vmlinux.bin.gz FORCE diff --git a/arch/xtensa/include/asm/Kbuild b/arch/xtensa/include/asm/Kbuild index 095f0a2244f7..1b982641ec35 100644 --- a/arch/xtensa/include/asm/Kbuild +++ b/arch/xtensa/include/asm/Kbuild @@ -15,6 +15,7 @@ generic-y += irq_regs.h generic-y += kdebug.h generic-y += kmap_types.h generic-y += kvm_para.h +generic-y += linkage.h generic-y += local.h generic-y += local64.h generic-y += percpu.h diff --git a/arch/xtensa/include/asm/ftrace.h b/arch/xtensa/include/asm/ftrace.h index 40a8c178f10d..36dc7a684397 100644 --- a/arch/xtensa/include/asm/ftrace.h +++ b/arch/xtensa/include/asm/ftrace.h @@ -1 +1,33 @@ -/* empty */ +/* + * arch/xtensa/include/asm/ftrace.h + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright (C) 2013 Tensilica Inc. + */ +#ifndef _XTENSA_FTRACE_H +#define _XTENSA_FTRACE_H + +#include <asm/processor.h> + +#define HAVE_ARCH_CALLER_ADDR +#define CALLER_ADDR0 ({ unsigned long a0, a1; \ + __asm__ __volatile__ ( \ + "mov %0, a0\n" \ + "mov %1, a1\n" \ + : "=r"(a0), "=r"(a1) : : ); \ + MAKE_PC_FROM_RA(a0, a1); }) +#ifdef CONFIG_FRAME_POINTER +extern unsigned long return_address(unsigned level); +#define CALLER_ADDR1 return_address(1) +#define CALLER_ADDR2 return_address(2) +#define CALLER_ADDR3 return_address(3) +#else +#define CALLER_ADDR1 (0) +#define CALLER_ADDR2 (0) +#define CALLER_ADDR3 (0) +#endif + +#endif /* _XTENSA_FTRACE_H */ diff --git a/arch/xtensa/include/asm/initialize_mmu.h b/arch/xtensa/include/asm/initialize_mmu.h index e1f8ba4061ed..722553f17db3 100644 --- a/arch/xtensa/include/asm/initialize_mmu.h +++ b/arch/xtensa/include/asm/initialize_mmu.h @@ -23,6 +23,9 @@ #ifndef _XTENSA_INITIALIZE_MMU_H #define _XTENSA_INITIALIZE_MMU_H +#include <asm/pgtable.h> +#include <asm/vectors.h> + #ifdef __ASSEMBLY__ #define XTENSA_HWVERSION_RC_2009_0 230000 @@ -48,6 +51,110 @@ * (XCHAL_HW_MIN_VERSION >= XTENSA_HWVERSION_RC_2009_0) */ +#if defined(CONFIG_MMU) && XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY +/* + * Have MMU v3 + */ + +#if !XCHAL_HAVE_VECBASE +# error "MMU v3 requires reloc vectors" +#endif + + movi a1, 0 + _call0 1f + _j 2f + + .align 4 +1: movi a2, 0x10000000 + movi a3, 0x18000000 + add a2, a2, a0 +9: bgeu a2, a3, 9b /* PC is out of the expected range */ + + /* Step 1: invalidate mapping at 0x40000000..0x5FFFFFFF. */ + + movi a2, 0x40000006 + idtlb a2 + iitlb a2 + isync + + /* Step 2: map 0x40000000..0x47FFFFFF to paddr containing this code + * and jump to the new mapping. + */ +#define CA_BYPASS (_PAGE_CA_BYPASS | _PAGE_HW_WRITE | _PAGE_HW_EXEC) +#define CA_WRITEBACK (_PAGE_CA_WB | _PAGE_HW_WRITE | _PAGE_HW_EXEC) + + srli a3, a0, 27 + slli a3, a3, 27 + addi a3, a3, CA_BYPASS + addi a7, a2, -1 + wdtlb a3, a7 + witlb a3, a7 + isync + + slli a4, a0, 5 + srli a4, a4, 5 + addi a5, a2, -6 + add a4, a4, a5 + jx a4 + + /* Step 3: unmap everything other than current area. + * Start at 0x60000000, wrap around, and end with 0x20000000 + */ +2: movi a4, 0x20000000 + add a5, a2, a4 +3: idtlb a5 + iitlb a5 + add a5, a5, a4 + bne a5, a2, 3b + + /* Step 4: Setup MMU with the old V2 mappings. */ + movi a6, 0x01000000 + wsr a6, ITLBCFG + wsr a6, DTLBCFG + isync + + movi a5, 0xd0000005 + movi a4, CA_WRITEBACK + wdtlb a4, a5 + witlb a4, a5 + + movi a5, 0xd8000005 + movi a4, CA_BYPASS + wdtlb a4, a5 + witlb a4, a5 + + movi a5, 0xe0000006 + movi a4, 0xf0000000 + CA_WRITEBACK + wdtlb a4, a5 + witlb a4, a5 + + movi a5, 0xf0000006 + movi a4, 0xf0000000 + CA_BYPASS + wdtlb a4, a5 + witlb a4, a5 + + isync + + /* Jump to self, using MMU v2 mappings. */ + movi a4, 1f + jx a4 + +1: + movi a2, VECBASE_RESET_VADDR + wsr a2, vecbase + + /* Step 5: remove temporary mapping. */ + idtlb a7 + iitlb a7 + isync + + movi a0, 0 + wsr a0, ptevaddr + rsync + +#endif /* defined(CONFIG_MMU) && XCHAL_HAVE_PTP_MMU && + XCHAL_HAVE_SPANNING_WAY */ + .endm #endif /*__ASSEMBLY__*/ diff --git a/arch/xtensa/include/asm/irqflags.h b/arch/xtensa/include/asm/irqflags.h index f865b1c1eae4..ea36674c6ec5 100644 --- a/arch/xtensa/include/asm/irqflags.h +++ b/arch/xtensa/include/asm/irqflags.h @@ -47,7 +47,10 @@ static inline void arch_local_irq_restore(unsigned long flags) static inline bool arch_irqs_disabled_flags(unsigned long flags) { - return (flags & 0xf) != 0; +#if XCHAL_EXCM_LEVEL < LOCKLEVEL || (1 << PS_EXCM_BIT) < LOCKLEVEL +#error "XCHAL_EXCM_LEVEL and 1<<PS_EXCM_BIT must be no less than LOCKLEVEL" +#endif + return (flags & (PS_INTLEVEL_MASK | (1 << PS_EXCM_BIT))) >= LOCKLEVEL; } static inline bool arch_irqs_disabled(void) diff --git a/arch/xtensa/include/asm/linkage.h b/arch/xtensa/include/asm/linkage.h deleted file mode 100644 index bf2128a99d79..000000000000 --- a/arch/xtensa/include/asm/linkage.h +++ /dev/null @@ -1,16 +0,0 @@ -/* - * include/asm-xtensa/linkage.h - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Copyright (C) 2001 - 2005 Tensilica Inc. - */ - -#ifndef _XTENSA_LINKAGE_H -#define _XTENSA_LINKAGE_H - -/* Nothing to do here ... */ - -#endif /* _XTENSA_LINKAGE_H */ diff --git a/arch/xtensa/include/asm/stacktrace.h b/arch/xtensa/include/asm/stacktrace.h new file mode 100644 index 000000000000..6a05fcb0a20d --- /dev/null +++ b/arch/xtensa/include/asm/stacktrace.h @@ -0,0 +1,36 @@ +/* + * arch/xtensa/include/asm/stacktrace.h + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright (C) 2001 - 2013 Tensilica Inc. + */ +#ifndef _XTENSA_STACKTRACE_H +#define _XTENSA_STACKTRACE_H + +#include <linux/sched.h> + +struct stackframe { + unsigned long pc; + unsigned long sp; +}; + +static __always_inline unsigned long *stack_pointer(struct task_struct *task) +{ + unsigned long *sp; + + if (!task || task == current) + __asm__ __volatile__ ("mov %0, a1\n" : "=a"(sp)); + else + sp = (unsigned long *)task->thread.sp; + + return sp; +} + +void walk_stackframe(unsigned long *sp, + int (*fn)(struct stackframe *frame, void *data), + void *data); + +#endif /* _XTENSA_STACKTRACE_H */ diff --git a/arch/xtensa/include/asm/timex.h b/arch/xtensa/include/asm/timex.h index 9e85ce8bd8dd..3d35e5d0367e 100644 --- a/arch/xtensa/include/asm/timex.h +++ b/arch/xtensa/include/asm/timex.h @@ -19,13 +19,16 @@ #define _INTLEVEL(x) XCHAL_INT ## x ## _LEVEL #define INTLEVEL(x) _INTLEVEL(x) -#if INTLEVEL(XCHAL_TIMER0_INTERRUPT) <= XCHAL_EXCM_LEVEL +#if XCHAL_NUM_TIMERS > 0 && \ + INTLEVEL(XCHAL_TIMER0_INTERRUPT) <= XCHAL_EXCM_LEVEL # define LINUX_TIMER 0 # define LINUX_TIMER_INT XCHAL_TIMER0_INTERRUPT -#elif INTLEVEL(XCHAL_TIMER1_INTERRUPT) <= XCHAL_EXCM_LEVEL +#elif XCHAL_NUM_TIMERS > 1 && \ + INTLEVEL(XCHAL_TIMER1_INTERRUPT) <= XCHAL_EXCM_LEVEL # define LINUX_TIMER 1 # define LINUX_TIMER_INT XCHAL_TIMER1_INTERRUPT -#elif INTLEVEL(XCHAL_TIMER2_INTERRUPT) <= XCHAL_EXCM_LEVEL +#elif XCHAL_NUM_TIMERS > 2 && \ + INTLEVEL(XCHAL_TIMER2_INTERRUPT) <= XCHAL_EXCM_LEVEL # define LINUX_TIMER 2 # define LINUX_TIMER_INT XCHAL_TIMER2_INTERRUPT #else diff --git a/arch/xtensa/include/asm/traps.h b/arch/xtensa/include/asm/traps.h index b5464ef3cf66..917488a0ab00 100644 --- a/arch/xtensa/include/asm/traps.h +++ b/arch/xtensa/include/asm/traps.h @@ -22,10 +22,9 @@ extern void do_unhandled(struct pt_regs *regs, unsigned long exccause); static inline void spill_registers(void) { - unsigned int a0, ps; __asm__ __volatile__ ( - "movi a14, " __stringify(PS_EXCM_BIT | LOCKLEVEL) "\n\t" + "movi a14, "__stringify((1 << PS_EXCM_BIT) | LOCKLEVEL)"\n\t" "mov a12, a0\n\t" "rsr a13, sar\n\t" "xsr a14, ps\n\t" @@ -35,7 +34,7 @@ static inline void spill_registers(void) "mov a0, a12\n\t" "wsr a13, sar\n\t" "wsr a14, ps\n\t" - : : "a" (&a0), "a" (&ps) + : : #if defined(CONFIG_FRAME_POINTER) : "a2", "a3", "a4", "a11", "a12", "a13", "a14", "a15", #else diff --git a/arch/xtensa/include/asm/vectors.h b/arch/xtensa/include/asm/vectors.h new file mode 100644 index 000000000000..c52b656d0310 --- /dev/null +++ b/arch/xtensa/include/asm/vectors.h @@ -0,0 +1,125 @@ +/* + * arch/xtensa/include/asm/xchal_vaddr_remap.h + * + * Xtensa macros for MMU V3 Support. Deals with re-mapping the Virtual + * Memory Addresses from "Virtual == Physical" to their prevvious V2 MMU + * mappings (KSEG at 0xD0000000 and KIO at 0XF0000000). + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright (C) 2008 - 2012 Tensilica Inc. + * + * Pete Delaney <piet@tensilica.com> + * Marc Gauthier <marc@tensilica.com + */ + +#ifndef _XTENSA_VECTORS_H +#define _XTENSA_VECTORS_H + +#include <variant/core.h> + +#if defined(CONFIG_MMU) + +/* Will Become VECBASE */ +#define VIRTUAL_MEMORY_ADDRESS 0xD0000000 + +/* Image Virtual Start Address */ +#define KERNELOFFSET 0xD0003000 + +#if defined(XCHAL_HAVE_PTP_MMU) && XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY + /* MMU v3 - XCHAL_HAVE_PTP_MMU == 1 */ + #define PHYSICAL_MEMORY_ADDRESS 0x00000000 + #define LOAD_MEMORY_ADDRESS 0x00003000 +#else + /* MMU V2 - XCHAL_HAVE_PTP_MMU == 0 */ + #define PHYSICAL_MEMORY_ADDRESS 0xD0000000 + #define LOAD_MEMORY_ADDRESS 0xD0003000 +#endif + +#else /* !defined(CONFIG_MMU) */ + /* MMU Not being used - Virtual == Physical */ + + /* VECBASE */ + #define VIRTUAL_MEMORY_ADDRESS 0x00002000 + + /* Location of the start of the kernel text, _start */ + #define KERNELOFFSET 0x00003000 + #define PHYSICAL_MEMORY_ADDRESS 0x00000000 + + /* Loaded just above possibly live vectors */ + #define LOAD_MEMORY_ADDRESS 0x00003000 + +#endif /* CONFIG_MMU */ + +#define XC_VADDR(offset) (VIRTUAL_MEMORY_ADDRESS + offset) +#define XC_PADDR(offset) (PHYSICAL_MEMORY_ADDRESS + offset) + +/* Used to set VECBASE register */ +#define VECBASE_RESET_VADDR VIRTUAL_MEMORY_ADDRESS + +#define RESET_VECTOR_VECOFS (XCHAL_RESET_VECTOR_VADDR - \ + VECBASE_RESET_VADDR) +#define RESET_VECTOR_VADDR XC_VADDR(RESET_VECTOR_VECOFS) + +#define RESET_VECTOR1_VECOFS (XCHAL_RESET_VECTOR1_VADDR - \ + VECBASE_RESET_VADDR) +#define RESET_VECTOR1_VADDR XC_VADDR(RESET_VECTOR1_VECOFS) + +#if XCHAL_HAVE_VECBASE + +#define USER_VECTOR_VADDR XC_VADDR(XCHAL_USER_VECOFS) +#define KERNEL_VECTOR_VADDR XC_VADDR(XCHAL_KERNEL_VECOFS) +#define DOUBLEEXC_VECTOR_VADDR XC_VADDR(XCHAL_DOUBLEEXC_VECOFS) +#define WINDOW_VECTORS_VADDR XC_VADDR(XCHAL_WINDOW_OF4_VECOFS) +#define INTLEVEL2_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL2_VECOFS) +#define INTLEVEL3_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL3_VECOFS) +#define INTLEVEL4_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL4_VECOFS) +#define INTLEVEL5_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL5_VECOFS) +#define INTLEVEL6_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL6_VECOFS) + +#define DEBUG_VECTOR_VADDR XC_VADDR(XCHAL_DEBUG_VECOFS) + +#undef XCHAL_NMI_VECTOR_VADDR +#define XCHAL_NMI_VECTOR_VADDR XC_VADDR(XCHAL_NMI_VECOFS) + +#undef XCHAL_INTLEVEL7_VECTOR_VADDR +#define XCHAL_INTLEVEL7_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL7_VECOFS) + +/* + * These XCHAL_* #defines from varian/core.h + * are not valid to use with V3 MMU. Non-XCHAL + * constants are defined above and should be used. + */ +#undef XCHAL_VECBASE_RESET_VADDR +#undef XCHAL_RESET_VECTOR0_VADDR +#undef XCHAL_USER_VECTOR_VADDR +#undef XCHAL_KERNEL_VECTOR_VADDR +#undef XCHAL_DOUBLEEXC_VECTOR_VADDR +#undef XCHAL_WINDOW_VECTORS_VADDR +#undef XCHAL_INTLEVEL2_VECTOR_VADDR +#undef XCHAL_INTLEVEL3_VECTOR_VADDR +#undef XCHAL_INTLEVEL4_VECTOR_VADDR +#undef XCHAL_INTLEVEL5_VECTOR_VADDR +#undef XCHAL_INTLEVEL6_VECTOR_VADDR +#undef XCHAL_DEBUG_VECTOR_VADDR +#undef XCHAL_NMI_VECTOR_VADDR +#undef XCHAL_INTLEVEL7_VECTOR_VADDR + +#else + +#define USER_VECTOR_VADDR XCHAL_USER_VECTOR_VADDR +#define KERNEL_VECTOR_VADDR XCHAL_KERNEL_VECTOR_VADDR +#define DOUBLEEXC_VECTOR_VADDR XCHAL_DOUBLEEXC_VECTOR_VADDR +#define WINDOW_VECTORS_VADDR XCHAL_WINDOW_VECTORS_VADDR +#define INTLEVEL2_VECTOR_VADDR XCHAL_INTLEVEL2_VECTOR_VADDR +#define INTLEVEL3_VECTOR_VADDR XCHAL_INTLEVEL3_VECTOR_VADDR +#define INTLEVEL4_VECTOR_VADDR XCHAL_INTLEVEL4_VECTOR_VADDR +#define INTLEVEL5_VECTOR_VADDR XCHAL_INTLEVEL5_VECTOR_VADDR +#define INTLEVEL6_VECTOR_VADDR XCHAL_INTLEVEL6_VECTOR_VADDR +#define DEBUG_VECTOR_VADDR XCHAL_DEBUG_VECTOR_VADDR + +#endif + +#endif /* _XTENSA_VECTORS_H */ diff --git a/arch/xtensa/kernel/Makefile b/arch/xtensa/kernel/Makefile index c3a59d992ac0..1e7fc87a94bb 100644 --- a/arch/xtensa/kernel/Makefile +++ b/arch/xtensa/kernel/Makefile @@ -4,14 +4,16 @@ extra-y := head.o vmlinux.lds -obj-y := align.o entry.o irq.o coprocessor.o process.o ptrace.o \ - setup.o signal.o syscall.o time.o traps.o vectors.o platform.o \ - pci-dma.o +obj-y := align.o coprocessor.o entry.o irq.o pci-dma.o platform.o process.o \ + ptrace.o setup.o signal.o stacktrace.o syscall.o time.o traps.o \ + vectors.o obj-$(CONFIG_KGDB) += xtensa-stub.o obj-$(CONFIG_PCI) += pci.o obj-$(CONFIG_MODULES) += xtensa_ksyms.o module.o +AFLAGS_head.o += -mtext-section-literals + # In the Xtensa architecture, assembly generates literals which must always # precede the L32R instruction with a relative offset less than 256 kB. # Therefore, the .text and .literal section must be combined in parenthesis diff --git a/arch/xtensa/kernel/entry.S b/arch/xtensa/kernel/entry.S index 63845f950792..5082507d5631 100644 --- a/arch/xtensa/kernel/entry.S +++ b/arch/xtensa/kernel/entry.S @@ -354,16 +354,16 @@ common_exception: * so we can allow exceptions and interrupts (*) again. * Set PS(EXCM = 0, UM = 0, RING = 0, OWB = 0, WOE = 1, INTLEVEL = X) * - * (*) We only allow interrupts of higher priority than current IRQ + * (*) We only allow interrupts if they were previously enabled and + * we're not handling an IRQ */ rsr a3, ps - addi a0, a0, -4 - movi a2, 1 + addi a0, a0, -EXCCAUSE_LEVEL1_INTERRUPT + movi a2, LOCKLEVEL extui a3, a3, PS_INTLEVEL_SHIFT, PS_INTLEVEL_WIDTH # a3 = PS.INTLEVEL - movnez a2, a3, a3 # a2 = 1: level-1, > 1: high priority - moveqz a3, a2, a0 # a3 = IRQ level iff interrupt + moveqz a3, a2, a0 # a3 = LOCKLEVEL iff interrupt movi a2, 1 << PS_WOE_BIT or a3, a3, a2 rsr a0, exccause @@ -389,6 +389,22 @@ common_exception: save_xtregs_opt a1 a2 a4 a5 a6 a7 PT_XTREGS_OPT +#ifdef CONFIG_TRACE_IRQFLAGS + l32i a4, a1, PT_DEPC + /* Double exception means we came here with an exception + * while PS.EXCM was set, i.e. interrupts disabled. + */ + bgeui a4, VALID_DOUBLE_EXCEPTION_ADDRESS, 1f + l32i a4, a1, PT_EXCCAUSE + bnei a4, EXCCAUSE_LEVEL1_INTERRUPT, 1f + /* We came here with an interrupt means interrupts were enabled + * and we've just disabled them. + */ + movi a4, trace_hardirqs_off + callx4 a4 +1: +#endif + /* Go to second-level dispatcher. Set up parameters to pass to the * exception handler and call the exception handler. */ @@ -407,11 +423,29 @@ common_exception: .global common_exception_return common_exception_return: +#ifdef CONFIG_TRACE_IRQFLAGS + l32i a4, a1, PT_DEPC + /* Double exception means we came here with an exception + * while PS.EXCM was set, i.e. interrupts disabled. + */ + bgeui a4, VALID_DOUBLE_EXCEPTION_ADDRESS, 1f + l32i a4, a1, PT_EXCCAUSE + bnei a4, EXCCAUSE_LEVEL1_INTERRUPT, 1f + /* We came here with an interrupt means interrupts were enabled + * and we'll reenable them on return. + */ + movi a4, trace_hardirqs_on + callx4 a4 +1: +#endif + /* Jump if we are returning from kernel exceptions. */ 1: l32i a3, a1, PT_PS _bbci.l a3, PS_UM_BIT, 4f + rsil a2, 0 + /* Specific to a user exception exit: * We need to check some flags for signal handling and rescheduling, * and have to restore WB and WS, extra states, and all registers @@ -652,51 +686,19 @@ common_exception_exit: l32i a0, a1, PT_DEPC l32i a3, a1, PT_AREG3 - _bltui a0, VALID_DOUBLE_EXCEPTION_ADDRESS, 1f - - wsr a0, depc l32i a2, a1, PT_AREG2 - l32i a0, a1, PT_AREG0 - l32i a1, a1, PT_AREG1 - rfde + _bgeui a0, VALID_DOUBLE_EXCEPTION_ADDRESS, 1f -1: /* Restore a0...a3 and return */ - rsr a0, ps - extui a2, a0, PS_INTLEVEL_SHIFT, PS_INTLEVEL_WIDTH - movi a0, 2f - slli a2, a2, 4 - add a0, a2, a0 - l32i a2, a1, PT_AREG2 - jx a0 - - .macro irq_exit_level level - .align 16 - .if XCHAL_EXCM_LEVEL >= \level - l32i a0, a1, PT_PC - wsr a0, epc\level l32i a0, a1, PT_AREG0 l32i a1, a1, PT_AREG1 - rfi \level - .endif - .endm + rfe - .align 16 -2: +1: wsr a0, depc l32i a0, a1, PT_AREG0 l32i a1, a1, PT_AREG1 - rfe - - .align 16 - /* no rfi for level-1 irq, handled by rfe above*/ - nop - - irq_exit_level 2 - irq_exit_level 3 - irq_exit_level 4 - irq_exit_level 5 - irq_exit_level 6 + rfde ENDPROC(kernel_exception) diff --git a/arch/xtensa/kernel/head.S b/arch/xtensa/kernel/head.S index df88f98737f4..ef12c0e6fa25 100644 --- a/arch/xtensa/kernel/head.S +++ b/arch/xtensa/kernel/head.S @@ -48,17 +48,36 @@ */ __HEAD + .begin no-absolute-literals + ENTRY(_start) - _j 2f + /* Preserve the pointer to the boot parameter list in EXCSAVE_1 */ + wsr a2, excsave1 + _j _SetupMMU + + .align 4 + .literal_position +.Lstartup: + .word _startup + .align 4 -1: .word _startup -2: l32r a0, 1b + .global _SetupMMU +_SetupMMU: + Offset = _SetupMMU - _start + +#ifdef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX + initialize_mmu +#endif + .end no-absolute-literals + + l32r a0, .Lstartup jx a0 ENDPROC(_start) - .section .init.text, "ax" + __INIT + .literal_position ENTRY(_startup) @@ -67,10 +86,6 @@ ENTRY(_startup) movi a0, LOCKLEVEL wsr a0, ps - /* Preserve the pointer to the boot parameter list in EXCSAVE_1 */ - - wsr a2, excsave1 - /* Start with a fresh windowbase and windowstart. */ movi a1, 1 @@ -86,7 +101,9 @@ ENTRY(_startup) /* Clear debugging registers. */ #if XCHAL_HAVE_DEBUG +#if XCHAL_NUM_IBREAK > 0 wsr a0, ibreakenable +#endif wsr a0, icount movi a1, 15 wsr a0, icountlevel @@ -156,8 +173,6 @@ ENTRY(_startup) isync - initialize_mmu - /* Unpack data sections * * The linker script used to build the Linux kernel image @@ -205,6 +220,10 @@ ENTRY(_startup) ___flush_dcache_all a2 a3 #endif + memw + isync + ___invalidate_icache_all a2 a3 + isync /* Setup stack and enable window exceptions (keep irqs disabled) */ diff --git a/arch/xtensa/kernel/platform.c b/arch/xtensa/kernel/platform.c index 44bf21c3769a..2bd6c351f37c 100644 --- a/arch/xtensa/kernel/platform.c +++ b/arch/xtensa/kernel/platform.c @@ -36,6 +36,7 @@ _F(void, power_off, (void), { while(1); }); _F(void, idle, (void), { __asm__ __volatile__ ("waiti 0" ::: "memory"); }); _F(void, heartbeat, (void), { }); _F(int, pcibios_fixup, (void), { return 0; }); +_F(void, pcibios_init, (void), { }); #ifdef CONFIG_XTENSA_CALIBRATE_CCOUNT _F(void, calibrate_ccount, (void), diff --git a/arch/xtensa/kernel/stacktrace.c b/arch/xtensa/kernel/stacktrace.c new file mode 100644 index 000000000000..7d2c317bd98b --- /dev/null +++ b/arch/xtensa/kernel/stacktrace.c @@ -0,0 +1,120 @@ +/* + * arch/xtensa/kernel/stacktrace.c + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright (C) 2001 - 2013 Tensilica Inc. + */ +#include <linux/export.h> +#include <linux/sched.h> +#include <linux/stacktrace.h> + +#include <asm/stacktrace.h> +#include <asm/traps.h> + +void walk_stackframe(unsigned long *sp, + int (*fn)(struct stackframe *frame, void *data), + void *data) +{ + unsigned long a0, a1; + unsigned long sp_end; + + a1 = (unsigned long)sp; + sp_end = ALIGN(a1, THREAD_SIZE); + + spill_registers(); + + while (a1 < sp_end) { + struct stackframe frame; + + sp = (unsigned long *)a1; + + a0 = *(sp - 4); + a1 = *(sp - 3); + + if (a1 <= (unsigned long)sp) + break; + + frame.pc = MAKE_PC_FROM_RA(a0, a1); + frame.sp = a1; + + if (fn(&frame, data)) + return; + } +} + +#ifdef CONFIG_STACKTRACE + +struct stack_trace_data { + struct stack_trace *trace; + unsigned skip; +}; + +static int stack_trace_cb(struct stackframe *frame, void *data) +{ + struct stack_trace_data *trace_data = data; + struct stack_trace *trace = trace_data->trace; + + if (trace_data->skip) { + --trace_data->skip; + return 0; + } + if (!kernel_text_address(frame->pc)) + return 0; + + trace->entries[trace->nr_entries++] = frame->pc; + return trace->nr_entries >= trace->max_entries; +} + +void save_stack_trace_tsk(struct task_struct *task, struct stack_trace *trace) +{ + struct stack_trace_data trace_data = { + .trace = trace, + .skip = trace->skip, + }; + walk_stackframe(stack_pointer(task), stack_trace_cb, &trace_data); +} +EXPORT_SYMBOL_GPL(save_stack_trace_tsk); + +void save_stack_trace(struct stack_trace *trace) +{ + save_stack_trace_tsk(current, trace); +} +EXPORT_SYMBOL_GPL(save_stack_trace); + +#endif + +#ifdef CONFIG_FRAME_POINTER + +struct return_addr_data { + unsigned long addr; + unsigned skip; +}; + +static int return_address_cb(struct stackframe *frame, void *data) +{ + struct return_addr_data *r = data; + + if (r->skip) { + --r->skip; + return 0; + } + if (!kernel_text_address(frame->pc)) + return 0; + r->addr = frame->pc; + return 1; +} + +unsigned long return_address(unsigned level) +{ + struct return_addr_data r = { + .skip = level + 1, + }; + walk_stackframe(stack_pointer(NULL), return_address_cb, &r); + return r.addr; +} +EXPORT_SYMBOL(return_address); + +#endif diff --git a/arch/xtensa/kernel/traps.c b/arch/xtensa/kernel/traps.c index 458186dab5dc..3e8a05c874cd 100644 --- a/arch/xtensa/kernel/traps.c +++ b/arch/xtensa/kernel/traps.c @@ -11,7 +11,7 @@ * * Essentially rewritten for the Xtensa architecture port. * - * Copyright (C) 2001 - 2005 Tensilica Inc. + * Copyright (C) 2001 - 2013 Tensilica Inc. * * Joe Taylor <joe@tensilica.com, joetylr@yahoo.com> * Chris Zankel <chris@zankel.net> @@ -32,6 +32,7 @@ #include <linux/delay.h> #include <linux/hardirq.h> +#include <asm/stacktrace.h> #include <asm/ptrace.h> #include <asm/timex.h> #include <asm/uaccess.h> @@ -195,7 +196,6 @@ void do_multihit(struct pt_regs *regs, unsigned long exccause) /* * IRQ handler. - * PS.INTLEVEL is the current IRQ priority level. */ extern void do_IRQ(int, struct pt_regs *); @@ -212,18 +212,21 @@ void do_interrupt(struct pt_regs *regs) XCHAL_INTLEVEL6_MASK, XCHAL_INTLEVEL7_MASK, }; - unsigned level = get_sr(ps) & PS_INTLEVEL_MASK; - - if (WARN_ON_ONCE(level >= ARRAY_SIZE(int_level_mask))) - return; for (;;) { unsigned intread = get_sr(interrupt); unsigned intenable = get_sr(intenable); - unsigned int_at_level = intread & intenable & - int_level_mask[level]; + unsigned int_at_level = intread & intenable; + unsigned level; + + for (level = LOCKLEVEL; level > 0; --level) { + if (int_at_level & int_level_mask[level]) { + int_at_level &= int_level_mask[level]; + break; + } + } - if (!int_at_level) + if (level == 0) return; /* @@ -404,53 +407,25 @@ void show_regs(struct pt_regs * regs) regs->syscall); } -static __always_inline unsigned long *stack_pointer(struct task_struct *task) +static int show_trace_cb(struct stackframe *frame, void *data) { - unsigned long *sp; - - if (!task || task == current) - __asm__ __volatile__ ("mov %0, a1\n" : "=a"(sp)); - else - sp = (unsigned long *)task->thread.sp; - - return sp; + if (kernel_text_address(frame->pc)) { + printk(" [<%08lx>] ", frame->pc); + print_symbol("%s\n", frame->pc); + } + return 0; } void show_trace(struct task_struct *task, unsigned long *sp) { - unsigned long a0, a1, pc; - unsigned long sp_start, sp_end; - - if (sp) - a1 = (unsigned long)sp; - else - a1 = (unsigned long)stack_pointer(task); - - sp_start = a1 & ~(THREAD_SIZE-1); - sp_end = sp_start + THREAD_SIZE; + if (!sp) + sp = stack_pointer(task); printk("Call Trace:"); #ifdef CONFIG_KALLSYMS printk("\n"); #endif - spill_registers(); - - while (a1 > sp_start && a1 < sp_end) { - sp = (unsigned long*)a1; - - a0 = *(sp - 4); - a1 = *(sp - 3); - - if (a1 <= (unsigned long) sp) - break; - - pc = MAKE_PC_FROM_RA(a0, a1); - - if (kernel_text_address(pc)) { - printk(" [<%08lx>] ", pc); - print_symbol("%s\n", pc); - } - } + walk_stackframe(sp, show_trace_cb, NULL); printk("\n"); } diff --git a/arch/xtensa/kernel/vectors.S b/arch/xtensa/kernel/vectors.S index 82109b42e240..f9e175382aa9 100644 --- a/arch/xtensa/kernel/vectors.S +++ b/arch/xtensa/kernel/vectors.S @@ -50,6 +50,7 @@ #include <asm/processor.h> #include <asm/page.h> #include <asm/thread_info.h> +#include <asm/vectors.h> #define WINDOW_VECTORS_SIZE 0x180 @@ -220,7 +221,7 @@ ENTRY(_DoubleExceptionVector) xsr a0, depc # get DEPC, save a0 - movi a3, XCHAL_WINDOW_VECTORS_VADDR + movi a3, WINDOW_VECTORS_VADDR _bltu a0, a3, .Lfixup addi a3, a3, WINDOW_VECTORS_SIZE _bgeu a0, a3, .Lfixup @@ -385,9 +386,12 @@ ENDPROC(_DebugInterruptVector) .if XCHAL_EXCM_LEVEL >= \level .section .Level\level\()InterruptVector.text, "ax" ENTRY(_Level\level\()InterruptVector) - wsr a0, epc1 + wsr a0, excsave2 rsr a0, epc\level - xsr a0, epc1 + wsr a0, epc1 + movi a0, EXCCAUSE_LEVEL1_INTERRUPT + wsr a0, exccause + rsr a0, eps\level # branch to user or kernel vector j _SimulateUserKernelVectorException .endif @@ -439,10 +443,8 @@ ENDPROC(_WindowOverflow4) */ .align 4 _SimulateUserKernelVectorException: - wsr a0, excsave2 - movi a0, 4 # LEVEL1_INTERRUPT cause - wsr a0, exccause - rsr a0, ps + addi a0, a0, (1 << PS_EXCM_BIT) + wsr a0, ps bbsi.l a0, PS_UM_BIT, 1f # branch if user mode rsr a0, excsave2 # restore a0 j _KernelExceptionVector # simulate kernel vector exception diff --git a/arch/xtensa/kernel/vmlinux.lds.S b/arch/xtensa/kernel/vmlinux.lds.S index 14695240536d..21acd11b5df2 100644 --- a/arch/xtensa/kernel/vmlinux.lds.S +++ b/arch/xtensa/kernel/vmlinux.lds.S @@ -18,6 +18,7 @@ #include <asm/page.h> #include <asm/thread_info.h> +#include <asm/vectors.h> #include <variant/core.h> #include <platform/hardware.h> OUTPUT_ARCH(xtensa) @@ -30,7 +31,7 @@ jiffies = jiffies_64; #endif #ifndef KERNELOFFSET -#define KERNELOFFSET 0xd0001000 +#define KERNELOFFSET 0xd0003000 #endif /* Note: In the following macros, it would be nice to specify only the @@ -185,16 +186,16 @@ SECTIONS SECTION_VECTOR (_WindowVectors_text, .WindowVectors.text, - XCHAL_WINDOW_VECTORS_VADDR, 4, + WINDOW_VECTORS_VADDR, 4, .dummy) SECTION_VECTOR (_DebugInterruptVector_literal, .DebugInterruptVector.literal, - XCHAL_DEBUG_VECTOR_VADDR - 4, + DEBUG_VECTOR_VADDR - 4, SIZEOF(.WindowVectors.text), .WindowVectors.text) SECTION_VECTOR (_DebugInterruptVector_text, .DebugInterruptVector.text, - XCHAL_DEBUG_VECTOR_VADDR, + DEBUG_VECTOR_VADDR, 4, .DebugInterruptVector.literal) #undef LAST @@ -202,7 +203,7 @@ SECTIONS #if XCHAL_EXCM_LEVEL >= 2 SECTION_VECTOR (_Level2InterruptVector_text, .Level2InterruptVector.text, - XCHAL_INTLEVEL2_VECTOR_VADDR, + INTLEVEL2_VECTOR_VADDR, SIZEOF(LAST), LAST) # undef LAST # define LAST .Level2InterruptVector.text @@ -210,7 +211,7 @@ SECTIONS #if XCHAL_EXCM_LEVEL >= 3 SECTION_VECTOR (_Level3InterruptVector_text, .Level3InterruptVector.text, - XCHAL_INTLEVEL3_VECTOR_VADDR, + INTLEVEL3_VECTOR_VADDR, SIZEOF(LAST), LAST) # undef LAST # define LAST .Level3InterruptVector.text @@ -218,7 +219,7 @@ SECTIONS #if XCHAL_EXCM_LEVEL >= 4 SECTION_VECTOR (_Level4InterruptVector_text, .Level4InterruptVector.text, - XCHAL_INTLEVEL4_VECTOR_VADDR, + INTLEVEL4_VECTOR_VADDR, SIZEOF(LAST), LAST) # undef LAST # define LAST .Level4InterruptVector.text @@ -226,7 +227,7 @@ SECTIONS #if XCHAL_EXCM_LEVEL >= 5 SECTION_VECTOR (_Level5InterruptVector_text, .Level5InterruptVector.text, - XCHAL_INTLEVEL5_VECTOR_VADDR, + INTLEVEL5_VECTOR_VADDR, SIZEOF(LAST), LAST) # undef LAST # define LAST .Level5InterruptVector.text @@ -234,39 +235,39 @@ SECTIONS #if XCHAL_EXCM_LEVEL >= 6 SECTION_VECTOR (_Level6InterruptVector_text, .Level6InterruptVector.text, - XCHAL_INTLEVEL6_VECTOR_VADDR, + INTLEVEL6_VECTOR_VADDR, SIZEOF(LAST), LAST) # undef LAST # define LAST .Level6InterruptVector.text #endif SECTION_VECTOR (_KernelExceptionVector_literal, .KernelExceptionVector.literal, - XCHAL_KERNEL_VECTOR_VADDR - 4, + KERNEL_VECTOR_VADDR - 4, SIZEOF(LAST), LAST) #undef LAST SECTION_VECTOR (_KernelExceptionVector_text, .KernelExceptionVector.text, - XCHAL_KERNEL_VECTOR_VADDR, + KERNEL_VECTOR_VADDR, 4, .KernelExceptionVector.literal) SECTION_VECTOR (_UserExceptionVector_literal, .UserExceptionVector.literal, - XCHAL_USER_VECTOR_VADDR - 4, + USER_VECTOR_VADDR - 4, SIZEOF(.KernelExceptionVector.text), .KernelExceptionVector.text) SECTION_VECTOR (_UserExceptionVector_text, .UserExceptionVector.text, - XCHAL_USER_VECTOR_VADDR, + USER_VECTOR_VADDR, 4, .UserExceptionVector.literal) SECTION_VECTOR (_DoubleExceptionVector_literal, .DoubleExceptionVector.literal, - XCHAL_DOUBLEEXC_VECTOR_VADDR - 16, + DOUBLEEXC_VECTOR_VADDR - 16, SIZEOF(.UserExceptionVector.text), .UserExceptionVector.text) SECTION_VECTOR (_DoubleExceptionVector_text, .DoubleExceptionVector.text, - XCHAL_DOUBLEEXC_VECTOR_VADDR, + DOUBLEEXC_VECTOR_VADDR, 32, .DoubleExceptionVector.literal) @@ -284,11 +285,26 @@ SECTIONS . = ALIGN(0x10); .bootstrap : { *(.bootstrap.literal .bootstrap.text .bootstrap.data) } - .ResetVector.text XCHAL_RESET_VECTOR_VADDR : + .ResetVector.text RESET_VECTOR_VADDR : { *(.ResetVector.text) } + + /* + * This is a remapped copy of the Secondary Reset Vector Code. + * It keeps gdb in sync with the PC after switching + * to the temporary mapping used while setting up + * the V2 MMU mappings for Linux. + * + * Only debug information about this section is put in the kernel image. + */ + .SecondaryResetVector.remapped_text 0x46000000 (INFO): + { + *(.SecondaryResetVector.remapped_text) + } + + .xt.lit : { *(.xt.lit) } .xt.prop : { *(.xt.prop) } diff --git a/arch/xtensa/kernel/xtensa_ksyms.c b/arch/xtensa/kernel/xtensa_ksyms.c index afe058b24e6e..42c53c87c204 100644 --- a/arch/xtensa/kernel/xtensa_ksyms.c +++ b/arch/xtensa/kernel/xtensa_ksyms.c @@ -119,3 +119,8 @@ EXPORT_SYMBOL(outsl); EXPORT_SYMBOL(insb); EXPORT_SYMBOL(insw); EXPORT_SYMBOL(insl); + +extern long common_exception_return; +extern long _spill_registers; +EXPORT_SYMBOL(common_exception_return); +EXPORT_SYMBOL(_spill_registers); diff --git a/arch/xtensa/mm/mmu.c b/arch/xtensa/mm/mmu.c index 0f77f9d3bb8b..a1077570e383 100644 --- a/arch/xtensa/mm/mmu.c +++ b/arch/xtensa/mm/mmu.c @@ -24,15 +24,19 @@ void __init paging_init(void) */ void __init init_mmu(void) { - /* Writing zeros to the <t>TLBCFG special registers ensure - * that valid values exist in the register. For existing - * PGSZID<w> fields, zero selects the first element of the - * page-size array. For nonexistent PGSZID<w> fields, zero is - * the best value to write. Also, when changing PGSZID<w> +#if !(XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY) + /* + * Writing zeros to the instruction and data TLBCFG special + * registers ensure that valid values exist in the register. + * + * For existing PGSZID<w> fields, zero selects the first element + * of the page-size array. For nonexistent PGSZID<w> fields, + * zero is the best value to write. Also, when changing PGSZID<w> * fields, the corresponding TLB must be flushed. */ set_itlbcfg_register(0); set_dtlbcfg_register(0); +#endif flush_tlb_all(); /* Set rasid register to a known value. */ diff --git a/arch/xtensa/oprofile/backtrace.c b/arch/xtensa/oprofile/backtrace.c index 66f32ee2c982..5f03a593d84f 100644 --- a/arch/xtensa/oprofile/backtrace.c +++ b/arch/xtensa/oprofile/backtrace.c @@ -132,9 +132,7 @@ static void xtensa_backtrace_kernel(struct pt_regs *regs, unsigned int depth) pc = MAKE_PC_FROM_RA(a0, pc); /* Add the PC to the trace. */ - if (kernel_text_address(pc)) - oprofile_add_trace(pc); - + oprofile_add_trace(pc); if (pc == (unsigned long) &common_exception_return) { regs = (struct pt_regs *)a1; if (user_mode(regs)) { diff --git a/arch/xtensa/platforms/iss/console.c b/arch/xtensa/platforms/iss/console.c index da9866f7fecf..70cb408bc20d 100644 --- a/arch/xtensa/platforms/iss/console.c +++ b/arch/xtensa/platforms/iss/console.c @@ -56,13 +56,13 @@ static void rs_poll(unsigned long); static int rs_open(struct tty_struct *tty, struct file * filp) { tty->port = &serial_port; - spin_lock(&timer_lock); + spin_lock_bh(&timer_lock); if (tty->count == 1) { setup_timer(&serial_timer, rs_poll, (unsigned long)&serial_port); mod_timer(&serial_timer, jiffies + SERIAL_TIMER_VALUE); } - spin_unlock(&timer_lock); + spin_unlock_bh(&timer_lock); return 0; } @@ -99,14 +99,13 @@ static int rs_write(struct tty_struct * tty, static void rs_poll(unsigned long priv) { struct tty_port *port = (struct tty_port *)priv; - struct timeval tv = { .tv_sec = 0, .tv_usec = 0 }; int i = 0; unsigned char c; spin_lock(&timer_lock); - while (__simc(SYS_select_one, 0, XTISS_SELECT_ONE_READ, (int)&tv,0,0)){ - __simc (SYS_read, 0, (unsigned long)&c, 1, 0, 0); + while (simc_poll(0)) { + simc_read(0, &c, 1); tty_insert_flip_char(port, c, TTY_NORMAL); i++; } @@ -244,8 +243,7 @@ static void iss_console_write(struct console *co, const char *s, unsigned count) int len = strlen(s); if (s != 0 && *s != 0) - __simc (SYS_write, 1, (unsigned long)s, - count < len ? count : len,0,0); + simc_write(1, s, count < len ? count : len); } static struct tty_driver* iss_console_device(struct console *c, int *index) diff --git a/arch/xtensa/platforms/iss/include/platform/simcall.h b/arch/xtensa/platforms/iss/include/platform/simcall.h index b5a4edf02d76..12b15ad1e586 100644 --- a/arch/xtensa/platforms/iss/include/platform/simcall.h +++ b/arch/xtensa/platforms/iss/include/platform/simcall.h @@ -59,56 +59,58 @@ static int errno; -static inline int __simc(int a, int b, int c, int d, int e, int f) +static inline int __simc(int a, int b, int c, int d) { int ret; register int a1 asm("a2") = a; register int b1 asm("a3") = b; register int c1 asm("a4") = c; register int d1 asm("a5") = d; - register int e1 asm("a6") = e; - register int f1 asm("a7") = f; __asm__ __volatile__ ( "simcall\n" "mov %0, a2\n" "mov %1, a3\n" : "=a" (ret), "=a" (errno), "+r"(a1), "+r"(b1) - : "r"(c1), "r"(d1), "r"(e1), "r"(f1) + : "r"(c1), "r"(d1) : "memory"); return ret; } static inline int simc_open(const char *file, int flags, int mode) { - return __simc(SYS_open, (int) file, flags, mode, 0, 0); + return __simc(SYS_open, (int) file, flags, mode); } static inline int simc_close(int fd) { - return __simc(SYS_close, fd, 0, 0, 0, 0); + return __simc(SYS_close, fd, 0, 0); } static inline int simc_ioctl(int fd, int request, void *arg) { - return __simc(SYS_ioctl, fd, request, (int) arg, 0, 0); + return __simc(SYS_ioctl, fd, request, (int) arg); } static inline int simc_read(int fd, void *buf, size_t count) { - return __simc(SYS_read, fd, (int) buf, count, 0, 0); + return __simc(SYS_read, fd, (int) buf, count); } static inline int simc_write(int fd, const void *buf, size_t count) { - return __simc(SYS_write, fd, (int) buf, count, 0, 0); + return __simc(SYS_write, fd, (int) buf, count); } static inline int simc_poll(int fd) { struct timeval tv = { .tv_sec = 0, .tv_usec = 0 }; - return __simc(SYS_select_one, fd, XTISS_SELECT_ONE_READ, (int)&tv, - 0, 0); + return __simc(SYS_select_one, fd, XTISS_SELECT_ONE_READ, (int)&tv); +} + +static inline int simc_lseek(int fd, uint32_t off, int whence) +{ + return __simc(SYS_lseek, fd, off, whence); } #endif /* _XTENSA_PLATFORM_ISS_SIMCALL_H */ diff --git a/arch/xtensa/platforms/iss/setup.c b/arch/xtensa/platforms/iss/setup.c index e1700102f35e..da7d18240866 100644 --- a/arch/xtensa/platforms/iss/setup.c +++ b/arch/xtensa/platforms/iss/setup.c @@ -38,12 +38,6 @@ void __init platform_init(bp_tag_t* bootparam) } -#ifdef CONFIG_PCI -void platform_pcibios_init(void) -{ -} -#endif - void platform_halt(void) { pr_info(" ** Called platform_halt() **\n"); @@ -64,7 +58,9 @@ void platform_restart(void) "wsr a2, icountlevel\n\t" "movi a2, 0\n\t" "wsr a2, icount\n\t" +#if XCHAL_NUM_IBREAK > 0 "wsr a2, ibreakenable\n\t" +#endif "wsr a2, lcount\n\t" "movi a2, 0x1f\n\t" "wsr a2, ps\n\t" diff --git a/arch/xtensa/platforms/iss/simdisk.c b/arch/xtensa/platforms/iss/simdisk.c index fc3c91fd20f7..c0edb35424ce 100644 --- a/arch/xtensa/platforms/iss/simdisk.c +++ b/arch/xtensa/platforms/iss/simdisk.c @@ -85,7 +85,7 @@ static void simdisk_transfer(struct simdisk *dev, unsigned long sector, while (nbytes > 0) { unsigned long io; - __simc(SYS_lseek, dev->fd, offset, SEEK_SET, 0, 0); + simc_lseek(dev->fd, offset, SEEK_SET); if (write) io = simc_write(dev->fd, buffer, nbytes); else @@ -176,7 +176,7 @@ static int simdisk_attach(struct simdisk *dev, const char *filename) err = -ENODEV; goto out; } - dev->size = __simc(SYS_lseek, dev->fd, 0, SEEK_END, 0, 0); + dev->size = simc_lseek(dev->fd, 0, SEEK_END); set_capacity(dev->gd, dev->size >> SECTOR_SHIFT); dev->filename = filename; pr_info("SIMDISK: %s=%s\n", dev->gd->disk_name, dev->filename); diff --git a/arch/xtensa/platforms/xt2000/setup.c b/arch/xtensa/platforms/xt2000/setup.c index c7d90f17886e..f9bc87966290 100644 --- a/arch/xtensa/platforms/xt2000/setup.c +++ b/arch/xtensa/platforms/xt2000/setup.c @@ -69,7 +69,9 @@ void platform_restart(void) "wsr a2, icountlevel\n\t" "movi a2, 0\n\t" "wsr a2, icount\n\t" +#if XCHAL_NUM_IBREAK > 0 "wsr a2, ibreakenable\n\t" +#endif "wsr a2, lcount\n\t" "movi a2, 0x1f\n\t" "wsr a2, ps\n\t" diff --git a/arch/xtensa/platforms/xtfpga/setup.c b/arch/xtensa/platforms/xtfpga/setup.c index 9d888a2a5755..96ef8eeb064e 100644 --- a/arch/xtensa/platforms/xtfpga/setup.c +++ b/arch/xtensa/platforms/xtfpga/setup.c @@ -60,7 +60,9 @@ void platform_restart(void) "wsr a2, icountlevel\n\t" "movi a2, 0\n\t" "wsr a2, icount\n\t" +#if XCHAL_NUM_IBREAK > 0 "wsr a2, ibreakenable\n\t" +#endif "wsr a2, lcount\n\t" "movi a2, 0x1f\n\t" "wsr a2, ps\n\t" |