diff options
| -rw-r--r-- | arch/cris/arch-v10/drivers/Kconfig | 39 | ||||
| -rw-r--r-- | arch/cris/arch-v32/drivers/Kconfig | 12 | ||||
| -rw-r--r-- | drivers/ide/Kconfig | 35 |
3 files changed, 35 insertions, 51 deletions
diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig index faf8b4d3ca01..e3c0f2928149 100644 --- a/arch/cris/arch-v10/drivers/Kconfig +++ b/arch/cris/arch-v10/drivers/Kconfig @@ -542,45 +542,6 @@ config ETRAX_RS485_DISABLE_RECEIVER loopback. Not all products are able to do this in software only. Axis 2400/2401 must disable receiver. -config ETRAX_IDE - bool "ATA/IDE support" - select IDE - select BLK_DEV_IDE - select BLK_DEV_IDEDISK - select BLK_DEV_IDECD - select BLK_DEV_IDEDMA - select IDE_GENERIC - help - Enable this to get support for ATA/IDE. - You can't use parallel ports or SCSI ports - at the same time. - - -config ETRAX_IDE_DELAY - int "Delay for drives to regain consciousness" - depends on ETRAX_IDE - default 15 - help - Number of seconds to wait for IDE drives to spin up after an IDE - reset. -choice - prompt "IDE reset pin" - depends on ETRAX_IDE - default ETRAX_IDE_PB7_RESET - -config ETRAX_IDE_PB7_RESET - bool "Port_PB_Bit_7" - help - IDE reset on pin 7 on port B - -config ETRAX_IDE_G27_RESET - bool "Port_G_Bit_27" - help - IDE reset on pin 27 on port G - -endchoice - - config ETRAX_USB_HOST bool "USB host" select USB diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig index 7f72d7c9e1ce..9bccb5e2a960 100644 --- a/arch/cris/arch-v32/drivers/Kconfig +++ b/arch/cris/arch-v32/drivers/Kconfig @@ -582,18 +582,6 @@ config ETRAX_PE_CHANGEABLE_BITS that a user can change the value on using ioctl's. Bit set = changeable. -config ETRAX_IDE - bool "ATA/IDE support" - depends on ETRAX_ARCH_V32 - select IDE - select BLK_DEV_IDE - select BLK_DEV_IDEDISK - select BLK_DEV_IDECD - select BLK_DEV_IDEDMA - select IDE_GENERIC - help - Enables the ETRAX IDE driver. - config ETRAX_CARDBUS bool "Cardbus support" depends on ETRAX_ARCH_V32 diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig index ca8239a2c98a..403e3ffca4e0 100644 --- a/drivers/ide/Kconfig +++ b/drivers/ide/Kconfig @@ -882,6 +882,41 @@ config BLK_DEV_IDE_BAST Say Y here if you want to support the onboard IDE channels on the Simtec BAST or the Thorcom VR1000 +config ETRAX_IDE + bool "ETRAX IDE support" + depends on CRIS && BROKEN + select BLK_DEV_IDEDMA + select IDE_GENERIC + help + Enables the ETRAX IDE driver. + + You can't use parallel ports or SCSI ports at the same time. + +config ETRAX_IDE_DELAY + int "Delay for drives to regain consciousness" + depends on ETRAX_IDE && ETRAX_ARCH_V10 + default 15 + help + Number of seconds to wait for IDE drives to spin up after an IDE + reset. + +choice + prompt "IDE reset pin" + depends on ETRAX_IDE && ETRAX_ARCH_V10 + default ETRAX_IDE_PB7_RESET + +config ETRAX_IDE_PB7_RESET + bool "Port_PB_Bit_7" + help + IDE reset on pin 7 on port B + +config ETRAX_IDE_G27_RESET + bool "Port_G_Bit_27" + help + IDE reset on pin 27 on port G + +endchoice + config IDE_H8300 bool "H8300 IDE support" depends on H8300 |