diff options
| -rw-r--r-- | Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt | 1 | ||||
| -rw-r--r-- | drivers/phy/phy-sun4i-usb.c | 41 |
2 files changed, 33 insertions, 9 deletions
diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt index 0cebf7454517..95736d77fbb7 100644 --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -9,6 +9,7 @@ Required properties: * allwinner,sun7i-a20-usb-phy * allwinner,sun8i-a23-usb-phy * allwinner,sun8i-a33-usb-phy + * allwinner,sun8i-h3-usb-phy - reg : a list of offset + length pairs - reg-names : * "phy_ctrl" diff --git a/drivers/phy/phy-sun4i-usb.c b/drivers/phy/phy-sun4i-usb.c index 35b1fa3b71fe..bae54f7a1f48 100644 --- a/drivers/phy/phy-sun4i-usb.c +++ b/drivers/phy/phy-sun4i-usb.c @@ -47,6 +47,9 @@ #define REG_PHYBIST 0x08 #define REG_PHYTUNE 0x0c #define REG_PHYCTL_A33 0x10 +#define REG_PHY_UNK_H3 0x20 + +#define REG_PMU_UNK_H3 0x10 #define PHYCTL_DATA BIT(7) @@ -80,7 +83,7 @@ #define PHY_DISCON_TH_SEL 0x2a #define PHY_SQUELCH_DETECT 0x3c -#define MAX_PHYS 3 +#define MAX_PHYS 4 /* * Note do not raise the debounce time, we must report Vusb high within 100ms @@ -92,6 +95,7 @@ enum sun4i_usb_phy_type { sun4i_a10_phy, sun8i_a33_phy, + sun8i_h3_phy, }; struct sun4i_usb_phy_cfg { @@ -239,6 +243,7 @@ static int sun4i_usb_phy_init(struct phy *_phy) struct sun4i_usb_phy *phy = phy_get_drvdata(_phy); struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy); int ret; + u32 val; ret = clk_prepare_enable(phy->clk); if (ret) @@ -250,16 +255,26 @@ static int sun4i_usb_phy_init(struct phy *_phy) return ret; } - /* Enable USB 45 Ohm resistor calibration */ - if (phy->index == 0) - sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1); + if (data->cfg->type == sun8i_h3_phy) { + if (phy->index == 0) { + val = readl(data->base + REG_PHY_UNK_H3); + writel(val & ~1, data->base + REG_PHY_UNK_H3); + } + + val = readl(phy->pmu + REG_PMU_UNK_H3); + writel(val & ~2, phy->pmu + REG_PMU_UNK_H3); + } else { + /* Enable USB 45 Ohm resistor calibration */ + if (phy->index == 0) + sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1); - /* Adjust PHY's magnitude and rate */ - sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5); + /* Adjust PHY's magnitude and rate */ + sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5); - /* Disconnect threshold adjustment */ - sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL, - data->cfg->disc_thresh, 2); + /* Disconnect threshold adjustment */ + sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL, + data->cfg->disc_thresh, 2); + } sun4i_usb_phy_passby(phy, 1); @@ -726,6 +741,13 @@ static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = { .dedicated_clocks = true, }; +static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = { + .num_phys = 4, + .type = sun8i_h3_phy, + .disc_thresh = 3, + .dedicated_clocks = true, +}; + static const struct of_device_id sun4i_usb_phy_of_match[] = { { .compatible = "allwinner,sun4i-a10-usb-phy", .data = &sun4i_a10_cfg }, { .compatible = "allwinner,sun5i-a13-usb-phy", .data = &sun5i_a13_cfg }, @@ -733,6 +755,7 @@ static const struct of_device_id sun4i_usb_phy_of_match[] = { { .compatible = "allwinner,sun7i-a20-usb-phy", .data = &sun7i_a20_cfg }, { .compatible = "allwinner,sun8i-a23-usb-phy", .data = &sun8i_a23_cfg }, { .compatible = "allwinner,sun8i-a33-usb-phy", .data = &sun8i_a33_cfg }, + { .compatible = "allwinner,sun8i-h3-usb-phy", .data = &sun8i_h3_cfg }, { }, }; MODULE_DEVICE_TABLE(of, sun4i_usb_phy_of_match); |