summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--drivers/pinctrl/pinctrl-coh901.c56
1 files changed, 13 insertions, 43 deletions
diff --git a/drivers/pinctrl/pinctrl-coh901.c b/drivers/pinctrl/pinctrl-coh901.c
index b90c01144fea..724234c9b01b 100644
--- a/drivers/pinctrl/pinctrl-coh901.c
+++ b/drivers/pinctrl/pinctrl-coh901.c
@@ -26,36 +26,6 @@
#include <mach/gpio-u300.h>
/*
- * Bias modes for U300 GPIOs
- *
- * GPIO_U300_CONFIG_BIAS_UNKNOWN: this bias mode is not known to us
- * GPIO_U300_CONFIG_BIAS_FLOAT: no specific bias, the GPIO will float or state
- * is not controlled by software
- * GPIO_U300_CONFIG_BIAS_PULL_UP: the GPIO will be pulled up (usually with high
- * impedance to VDD)
- */
-#define GPIO_U300_CONFIG_BIAS_UNKNOWN 0x1000
-#define GPIO_U300_CONFIG_BIAS_FLOAT 0x1001
-#define GPIO_U300_CONFIG_BIAS_PULL_UP 0x1002
-
-/*
- * Drive modes for U300 GPIOs (output)
- *
- * GPIO_U300_CONFIG_DRIVE_PUSH_PULL: the GPIO will be driven actively high and
- * low, this is the most typical case and is typically achieved with two
- * active transistors on the output
- * GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN: the GPIO will be driven with open drain
- * (open collector) which means it is usually wired with other output
- * ports which are then pulled up with an external resistor
- * GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE: the GPIO will be driven with open drain
- * (open emitter) which is the same as open drain mutatis mutandis but
- * pulled to ground
- */
-#define GPIO_U300_CONFIG_DRIVE_PUSH_PULL 0x2000
-#define GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN 0x2001
-#define GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE 0x2002
-
-/*
* Register definitions for COH 901 335 variant
*/
#define U300_335_PORT_STRIDE (0x1C)
@@ -181,12 +151,12 @@ struct u300_gpio_confdata {
#define BS365_GPIO_NUM_PORTS 5
#define U300_FLOATING_INPUT { \
- .bias_mode = GPIO_U300_CONFIG_BIAS_FLOAT, \
+ .bias_mode = PIN_CONFIG_BIAS_HIGH_IMPEDANCE, \
.output = false, \
}
#define U300_PULL_UP_INPUT { \
- .bias_mode = GPIO_U300_CONFIG_BIAS_PULL_UP, \
+ .bias_mode = PIN_CONFIG_BIAS_PULL_UP, \
.output = false, \
}
@@ -449,7 +419,7 @@ static int u300_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
}
static int u300_gpio_config(struct gpio_chip *chip, unsigned offset,
- u16 param, unsigned long *data)
+ enum pin_config_param param, unsigned long data)
{
struct u300_gpio *gpio = to_u300_gpio(chip);
unsigned long flags;
@@ -457,16 +427,16 @@ static int u300_gpio_config(struct gpio_chip *chip, unsigned offset,
local_irq_save(flags);
switch (param) {
- case GPIO_U300_CONFIG_BIAS_UNKNOWN:
- case GPIO_U300_CONFIG_BIAS_FLOAT:
+ case PIN_CONFIG_BIAS_DISABLE:
+ case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
val = readl(U300_PIN_REG(offset, per));
writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
break;
- case GPIO_U300_CONFIG_BIAS_PULL_UP:
+ case PIN_CONFIG_BIAS_PULL_UP:
val = readl(U300_PIN_REG(offset, per));
writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
break;
- case GPIO_U300_CONFIG_DRIVE_PUSH_PULL:
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
val = readl(U300_PIN_REG(offset, pcr));
val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
<< ((offset & 0x07) << 1));
@@ -474,7 +444,7 @@ static int u300_gpio_config(struct gpio_chip *chip, unsigned offset,
<< ((offset & 0x07) << 1));
writel(val, U300_PIN_REG(offset, pcr));
break;
- case GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN:
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
val = readl(U300_PIN_REG(offset, pcr));
val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
<< ((offset & 0x07) << 1));
@@ -482,7 +452,7 @@ static int u300_gpio_config(struct gpio_chip *chip, unsigned offset,
<< ((offset & 0x07) << 1));
writel(val, U300_PIN_REG(offset, pcr));
break;
- case GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE:
+ case PIN_CONFIG_DRIVE_OPEN_SOURCE:
val = readl(U300_PIN_REG(offset, pcr));
val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
<< ((offset & 0x07) << 1));
@@ -651,12 +621,12 @@ static void __init u300_gpio_init_pin(struct u300_gpio *gpio,
/* Deactivate bias mode for output */
u300_gpio_config(&gpio->chip, offset,
- GPIO_U300_CONFIG_BIAS_FLOAT,
- NULL);
+ PIN_CONFIG_BIAS_HIGH_IMPEDANCE,
+ 0);
/* Set drive mode for output */
u300_gpio_config(&gpio->chip, offset,
- GPIO_U300_CONFIG_DRIVE_PUSH_PULL, NULL);
+ PIN_CONFIG_DRIVE_PUSH_PULL, 0);
dev_dbg(gpio->dev, "set up pin %d as output, value: %d\n",
offset, conf->outval);
@@ -667,7 +637,7 @@ static void __init u300_gpio_init_pin(struct u300_gpio *gpio,
u300_gpio_set(&gpio->chip, offset, 0);
/* Set bias mode for input */
- u300_gpio_config(&gpio->chip, offset, conf->bias_mode, NULL);
+ u300_gpio_config(&gpio->chip, offset, conf->bias_mode, 0);
dev_dbg(gpio->dev, "set up pin %d as input, bias: %04x\n",
offset, conf->bias_mode);