diff options
| -rw-r--r-- | Documentation/networking/stmmac.txt | 24 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/common.h | 3 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac1000.h | 2 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 42 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c | 6 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h | 1 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 4 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c | 3 | ||||
| -rw-r--r-- | include/linux/stmmac.h | 20 |
9 files changed, 89 insertions, 16 deletions
diff --git a/Documentation/networking/stmmac.txt b/Documentation/networking/stmmac.txt index 61f40a3fa7ea..eacb640286b1 100644 --- a/Documentation/networking/stmmac.txt +++ b/Documentation/networking/stmmac.txt @@ -111,7 +111,7 @@ and detailed below as well: int phy_addr; int interface; struct stmmac_mdio_bus_data *mdio_bus_data; - int pbl; + struct stmmac_dma_cfg *dma_cfg; int clk_csr; int has_gmac; int enh_desc; @@ -163,7 +163,7 @@ Where: o custom_cfg: this is a custom configuration that can be passed while initialising the resources. -The we have: +For MDIO bus The we have: struct stmmac_mdio_bus_data { int bus_id; @@ -180,10 +180,28 @@ Where: o irqs: list of IRQs, one per PHY. o probed_phy_irq: if irqs is NULL, use this for probed PHY. + +For DMA engine we have the following internal fields that should be +tuned according to the HW capabilities. + +struct stmmac_dma_cfg { + int pbl; + int fixed_burst; + int burst_len_supported; +}; + +Where: + o pbl: Programmable Burst Length + o fixed_burst: program the DMA to use the fixed burst mode + o burst_len: this is the value we put in the register + supported values are provided as macros in + linux/stmmac.h header file. + +--- + Below an example how the structures above are using on ST platforms. static struct plat_stmmacenet_data stxYYY_ethernet_platform_data = { - .pbl = 32, .has_gmac = 0, .enh_desc = 0, .fix_mac_speed = stxYYY_ethernet_fix_mac_speed, diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h index eec8d34b6c88..b14829f8085d 100644 --- a/drivers/net/ethernet/stmicro/stmmac/common.h +++ b/drivers/net/ethernet/stmicro/stmmac/common.h @@ -236,7 +236,8 @@ struct stmmac_desc_ops { struct stmmac_dma_ops { /* DMA core initialization */ - int (*init) (void __iomem *ioaddr, int pbl, u32 dma_tx, u32 dma_rx); + int (*init) (void __iomem *ioaddr, int pbl, int fb, int burst_len, + u32 dma_tx, u32 dma_rx); /* Dump DMA registers */ void (*dump_regs) (void __iomem *ioaddr); /* Set tx/rx threshold in the csr6 register diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h index cfcef0ea0fa5..54339a78e358 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h @@ -142,7 +142,7 @@ enum rx_tx_priority_ratio { #define DMA_BUS_MODE_RPBL_MASK 0x003e0000 /* Rx-Programmable Burst Len */ #define DMA_BUS_MODE_RPBL_SHIFT 17 #define DMA_BUS_MODE_USP 0x00800000 -#define DMA_BUS_MODE_4PBL 0x01000000 +#define DMA_BUS_MODE_PBL 0x01000000 #define DMA_BUS_MODE_AAL 0x02000000 /* DMA CRS Control and Status Register Mapping */ diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c index 4d5402a1d262..3675c5731565 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c @@ -30,8 +30,8 @@ #include "dwmac1000.h" #include "dwmac_dma.h" -static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, u32 dma_tx, - u32 dma_rx) +static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb, + int burst_len, u32 dma_tx, u32 dma_rx) { u32 value = readl(ioaddr + DMA_BUS_MODE); int limit; @@ -48,15 +48,47 @@ static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, u32 dma_tx, if (limit < 0) return -EBUSY; - value = /* DMA_BUS_MODE_FB | */ DMA_BUS_MODE_4PBL | - ((pbl << DMA_BUS_MODE_PBL_SHIFT) | - (pbl << DMA_BUS_MODE_RPBL_SHIFT)); + /* + * Set the DMA PBL (Programmable Burst Length) mode + * Before stmmac core 3.50 this mode bit was 4xPBL, and + * post 3.5 mode bit acts as 8*PBL. + * For core rev < 3.5, when the core is set for 4xPBL mode, the + * DMA transfers the data in 4, 8, 16, 32, 64 & 128 beats + * depending on pbl value. + * For core rev > 3.5, when the core is set for 8xPBL mode, the + * DMA transfers the data in 8, 16, 32, 64, 128 & 256 beats + * depending on pbl value. + */ + value = DMA_BUS_MODE_PBL | ((pbl << DMA_BUS_MODE_PBL_SHIFT) | + (pbl << DMA_BUS_MODE_RPBL_SHIFT)); + + /* Set the Fixed burst mode */ + if (fb) + value |= DMA_BUS_MODE_FB; #ifdef CONFIG_STMMAC_DA value |= DMA_BUS_MODE_DA; /* Rx has priority over tx */ #endif writel(value, ioaddr + DMA_BUS_MODE); + /* In case of GMAC AXI configuration, program the DMA_AXI_BUS_MODE + * for supported bursts. + * + * Note: This is applicable only for revision GMACv3.61a. For + * older version this register is reserved and shall have no + * effect. + * + * Note: + * For Fixed Burst Mode: if we directly write 0xFF to this + * register using the configurations pass from platform code, + * this would ensure that all bursts supported by core are set + * and those which are not supported would remain ineffective. + * + * For Non Fixed Burst Mode: provide the maximum value of the + * burst length. Any burst equal or below the provided burst + * length would be allowed to perform. */ + writel(burst_len, ioaddr + DMA_AXI_BUS_MODE); + /* Mask interrupts by writing to CSR7 */ writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA); diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c index bc17fd08b55d..92ed2e07609e 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c @@ -32,8 +32,8 @@ #include "dwmac100.h" #include "dwmac_dma.h" -static int dwmac100_dma_init(void __iomem *ioaddr, int pbl, u32 dma_tx, - u32 dma_rx) +static int dwmac100_dma_init(void __iomem *ioaddr, int pbl, int fb, + int burst_len, u32 dma_tx, u32 dma_rx) { u32 value = readl(ioaddr + DMA_BUS_MODE); int limit; @@ -52,7 +52,7 @@ static int dwmac100_dma_init(void __iomem *ioaddr, int pbl, u32 dma_tx, /* Enable Application Access by writing to DMA CSR0 */ writel(DMA_BUS_MODE_DEFAULT | (pbl << DMA_BUS_MODE_PBL_SHIFT), - ioaddr + DMA_BUS_MODE); + ioaddr + DMA_BUS_MODE); /* Mask interrupts by writing to CSR7 */ writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA); diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h b/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h index 437edacd602e..6e0360f9cfde 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h @@ -32,6 +32,7 @@ #define DMA_CONTROL 0x00001018 /* Ctrl (Operational Mode) */ #define DMA_INTR_ENA 0x0000101c /* Interrupt Enable */ #define DMA_MISSED_FRAME_CTR 0x00001020 /* Missed Frame Counter */ +#define DMA_AXI_BUS_MODE 0x00001028 /* AXI Bus Mode */ #define DMA_CUR_TX_BUF_ADDR 0x00001050 /* Current Host Tx Buffer */ #define DMA_CUR_RX_BUF_ADDR 0x00001054 /* Current Host Rx Buffer */ #define DMA_HW_FEATURE 0x00001058 /* HW Feature Register */ diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 84f6b348ec70..933f63c4b2f3 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -944,7 +944,9 @@ static int stmmac_open(struct net_device *dev) init_dma_desc_rings(dev); /* DMA initialization and SW reset */ - ret = priv->hw->dma->init(priv->ioaddr, priv->plat->pbl, + ret = priv->hw->dma->init(priv->ioaddr, priv->plat->dma_cfg->pbl, + priv->plat->dma_cfg->fixed_burst, + priv->plat->dma_cfg->burst_len, priv->dma_tx_phy, priv->dma_rx_phy); if (ret < 0) { pr_err("%s: DMA initialization failed\n", __func__); diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c index da66ed7c3c5d..65e0f98520d6 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c @@ -35,7 +35,8 @@ static void stmmac_default_data(void) plat_dat.bus_id = 1; plat_dat.phy_addr = 0; plat_dat.interface = PHY_INTERFACE_MODE_GMII; - plat_dat.pbl = 32; + plat_dat.dma_cfg->pbl = 32; + plat_dat.dma_cfg->burst_len = DMA_AXI_BLEN_256; plat_dat.clk_csr = 2; /* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */ plat_dat.has_gmac = 1; plat_dat.force_sf_dma_mode = 1; diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h index e5292828b684..4aef9baff12b 100644 --- a/include/linux/stmmac.h +++ b/include/linux/stmmac.h @@ -60,6 +60,18 @@ * 1110 clk_csr_i/16 * 1111 clk_csr_i/18 */ +/* AXI DMA Burst length suported */ +#define DMA_AXI_BLEN_4 (1 << 1) +#define DMA_AXI_BLEN_8 (1 << 2) +#define DMA_AXI_BLEN_16 (1 << 3) +#define DMA_AXI_BLEN_32 (1 << 4) +#define DMA_AXI_BLEN_64 (1 << 5) +#define DMA_AXI_BLEN_128 (1 << 6) +#define DMA_AXI_BLEN_256 (1 << 7) +#define DMA_AXI_BLEN_ALL (DMA_AXI_BLEN_4 | DMA_AXI_BLEN_8 | DMA_AXI_BLEN_16 \ + | DMA_AXI_BLEN_32 | DMA_AXI_BLEN_64 \ + | DMA_AXI_BLEN_128 | DMA_AXI_BLEN_256) + /* Platfrom data for platform device structure's platform_data field */ struct stmmac_mdio_bus_data { @@ -70,13 +82,19 @@ struct stmmac_mdio_bus_data { int probed_phy_irq; }; +struct stmmac_dma_cfg { + int pbl; + int fixed_burst; + int burst_len; +}; + struct plat_stmmacenet_data { char *phy_bus_name; int bus_id; int phy_addr; int interface; struct stmmac_mdio_bus_data *mdio_bus_data; - int pbl; + struct stmmac_dma_cfg *dma_cfg; int clk_csr; int has_gmac; int enh_desc; |