diff options
| -rw-r--r-- | drivers/gpu/drm/drm_dp_helper.c | 72 | ||||
| -rw-r--r-- | drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c | 44 | ||||
| -rw-r--r-- | include/drm/drm_dp_helper.h | 7 |
3 files changed, 89 insertions, 34 deletions
diff --git a/drivers/gpu/drm/drm_dp_helper.c b/drivers/gpu/drm/drm_dp_helper.c index af2aad2f4725..23f9073bc473 100644 --- a/drivers/gpu/drm/drm_dp_helper.c +++ b/drivers/gpu/drm/drm_dp_helper.c @@ -3290,6 +3290,10 @@ int drm_edp_backlight_set_level(struct drm_dp_aux *aux, const struct drm_edp_bac int ret; u8 buf[2] = { 0 }; + /* The panel uses the PWM for controlling brightness levels */ + if (!bl->aux_set) + return 0; + if (bl->lsb_reg_used) { buf[0] = (level & 0xff00) >> 8; buf[1] = (level & 0x00ff); @@ -3316,7 +3320,7 @@ drm_edp_backlight_set_enable(struct drm_dp_aux *aux, const struct drm_edp_backli int ret; u8 buf; - /* The panel uses something other then DPCD for enabling its backlight */ + /* This panel uses the EDP_BL_PWR GPIO for enablement */ if (!bl->aux_enable) return 0; @@ -3351,11 +3355,11 @@ drm_edp_backlight_set_enable(struct drm_dp_aux *aux, const struct drm_edp_backli * restoring any important backlight state such as the given backlight level, the brightness byte * count, backlight frequency, etc. * - * Note that certain panels, while supporting brightness level controls over DPCD, may not support - * having their backlights enabled via the standard %DP_EDP_DISPLAY_CONTROL_REGISTER. On such panels - * &drm_edp_backlight_info.aux_enable will be set to %false, this function will skip the step of - * programming the %DP_EDP_DISPLAY_CONTROL_REGISTER, and the driver must perform the required - * implementation specific step for enabling the backlight after calling this function. + * Note that certain panels do not support being enabled or disabled via DPCD, but instead require + * that the driver handle enabling/disabling the panel through implementation-specific means using + * the EDP_BL_PWR GPIO. For such panels, &drm_edp_backlight_info.aux_enable will be set to %false, + * this function becomes a no-op, and the driver is expected to handle powering the panel on using + * the EDP_BL_PWR GPIO. * * Returns: %0 on success, negative error code on failure. */ @@ -3363,7 +3367,12 @@ int drm_edp_backlight_enable(struct drm_dp_aux *aux, const struct drm_edp_backli const u16 level) { int ret; - u8 dpcd_buf = DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD; + u8 dpcd_buf; + + if (bl->aux_set) + dpcd_buf = DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD; + else + dpcd_buf = DP_EDP_BACKLIGHT_CONTROL_MODE_PWM; if (bl->pwmgen_bit_count) { ret = drm_dp_dpcd_writeb(aux, DP_EDP_PWMGEN_BIT_COUNT, bl->pwmgen_bit_count); @@ -3405,12 +3414,13 @@ EXPORT_SYMBOL(drm_edp_backlight_enable); * @aux: The DP AUX channel to use * @bl: Backlight capability info from drm_edp_backlight_init() * - * This function handles disabling DPCD backlight controls on a panel over AUX. Note that some - * panels have backlights that are enabled/disabled by other means, despite having their brightness - * values controlled through DPCD. On such panels &drm_edp_backlight_info.aux_enable will be set to - * %false, this function will become a no-op (and we will skip updating - * %DP_EDP_DISPLAY_CONTROL_REGISTER), and the driver must take care to perform it's own - * implementation specific step for disabling the backlight. + * This function handles disabling DPCD backlight controls on a panel over AUX. + * + * Note that certain panels do not support being enabled or disabled via DPCD, but instead require + * that the driver handle enabling/disabling the panel through implementation-specific means using + * the EDP_BL_PWR GPIO. For such panels, &drm_edp_backlight_info.aux_enable will be set to %false, + * this function becomes a no-op, and the driver is expected to handle powering the panel off using + * the EDP_BL_PWR GPIO. * * Returns: %0 on success or no-op, negative error code on failure. */ @@ -3434,6 +3444,9 @@ drm_edp_backlight_probe_max(struct drm_dp_aux *aux, struct drm_edp_backlight_inf int ret; u8 pn, pn_min, pn_max; + if (!bl->aux_set) + return 0; + ret = drm_dp_dpcd_readb(aux, DP_EDP_PWMGEN_BIT_COUNT, &pn); if (ret != 1) { drm_dbg_kms(aux->drm_dev, "%s: Failed to read pwmgen bit count cap: %d\n", @@ -3519,7 +3532,7 @@ drm_edp_backlight_probe_max(struct drm_dp_aux *aux, struct drm_edp_backlight_inf } static inline int -drm_edp_backlight_probe_level(struct drm_dp_aux *aux, struct drm_edp_backlight_info *bl, +drm_edp_backlight_probe_state(struct drm_dp_aux *aux, struct drm_edp_backlight_info *bl, u8 *current_mode) { int ret; @@ -3534,6 +3547,9 @@ drm_edp_backlight_probe_level(struct drm_dp_aux *aux, struct drm_edp_backlight_i } *current_mode = (mode_reg & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK); + if (!bl->aux_set) + return 0; + if (*current_mode == DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) { int size = 1 + bl->lsb_reg_used; @@ -3564,7 +3580,7 @@ drm_edp_backlight_probe_level(struct drm_dp_aux *aux, struct drm_edp_backlight_i * @bl: The &drm_edp_backlight_info struct to fill out with information on the backlight * @driver_pwm_freq_hz: Optional PWM frequency from the driver in hz * @edp_dpcd: A cached copy of the eDP DPCD - * @current_level: Where to store the probed brightness level + * @current_level: Where to store the probed brightness level, if any * @current_mode: Where to store the currently set backlight control mode * * Initializes a &drm_edp_backlight_info struct by probing @aux for it's backlight capabilities, @@ -3584,24 +3600,38 @@ drm_edp_backlight_init(struct drm_dp_aux *aux, struct drm_edp_backlight_info *bl if (edp_dpcd[1] & DP_EDP_BACKLIGHT_AUX_ENABLE_CAP) bl->aux_enable = true; + if (edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_AUX_SET_CAP) + bl->aux_set = true; if (edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_BYTE_COUNT) bl->lsb_reg_used = true; + /* Sanity check caps */ + if (!bl->aux_set && !(edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_PWM_PIN_CAP)) { + drm_dbg_kms(aux->drm_dev, + "%s: Panel supports neither AUX or PWM brightness control? Aborting\n", + aux->name); + return -EINVAL; + } + ret = drm_edp_backlight_probe_max(aux, bl, driver_pwm_freq_hz, edp_dpcd); if (ret < 0) return ret; - ret = drm_edp_backlight_probe_level(aux, bl, current_mode); + ret = drm_edp_backlight_probe_state(aux, bl, current_mode); if (ret < 0) return ret; *current_level = ret; drm_dbg_kms(aux->drm_dev, - "%s: Found backlight level=%d/%d pwm_freq_pre_divider=%d mode=%x\n", - aux->name, *current_level, bl->max, bl->pwm_freq_pre_divider, *current_mode); - drm_dbg_kms(aux->drm_dev, - "%s: Backlight caps: pwmgen_bit_count=%d lsb_reg_used=%d aux_enable=%d\n", - aux->name, bl->pwmgen_bit_count, bl->lsb_reg_used, bl->aux_enable); + "%s: Found backlight: aux_set=%d aux_enable=%d mode=%d\n", + aux->name, bl->aux_set, bl->aux_enable, *current_mode); + if (bl->aux_set) { + drm_dbg_kms(aux->drm_dev, + "%s: Backlight caps: level=%d/%d pwm_freq_pre_divider=%d lsb_reg_used=%d\n", + aux->name, *current_level, bl->max, bl->pwm_freq_pre_divider, + bl->lsb_reg_used); + } + return 0; } EXPORT_SYMBOL(drm_edp_backlight_init); diff --git a/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c b/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c index f05b71c01b8e..96fe3eaba44a 100644 --- a/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c +++ b/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c @@ -282,6 +282,12 @@ intel_dp_aux_vesa_set_backlight(const struct drm_connector_state *conn_state, u3 struct intel_panel *panel = &connector->panel; struct intel_dp *intel_dp = enc_to_intel_dp(connector->encoder); + if (!panel->backlight.edp.vesa.info.aux_set) { + const u32 pwm_level = intel_backlight_level_to_pwm(connector, level); + + intel_backlight_set_pwm_level(conn_state, pwm_level); + } + drm_edp_backlight_set_level(&intel_dp->aux, &panel->backlight.edp.vesa.info, level); } @@ -294,8 +300,13 @@ intel_dp_aux_vesa_enable_backlight(const struct intel_crtc_state *crtc_state, struct intel_dp *intel_dp = enc_to_intel_dp(connector->encoder); if (!panel->backlight.edp.vesa.info.aux_enable) { - u32 pwm_level = intel_backlight_invert_pwm_level(connector, - panel->backlight.pwm_level_max); + u32 pwm_level; + + if (!panel->backlight.edp.vesa.info.aux_set) + pwm_level = intel_backlight_level_to_pwm(connector, level); + else + pwm_level = intel_backlight_invert_pwm_level(connector, + panel->backlight.pwm_level_max); panel->backlight.pwm_funcs->enable(crtc_state, conn_state, pwm_level); } @@ -332,7 +343,7 @@ static int intel_dp_aux_vesa_setup_backlight(struct intel_connector *connector, if (ret < 0) return ret; - if (!panel->backlight.edp.vesa.info.aux_enable) { + if (!panel->backlight.edp.vesa.info.aux_set || !panel->backlight.edp.vesa.info.aux_enable) { ret = panel->backlight.pwm_funcs->setup(connector, pipe); if (ret < 0) { drm_err(&i915->drm, @@ -341,14 +352,27 @@ static int intel_dp_aux_vesa_setup_backlight(struct intel_connector *connector, return ret; } } - panel->backlight.max = panel->backlight.edp.vesa.info.max; - panel->backlight.min = 0; - if (current_mode == DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) { - panel->backlight.level = current_level; - panel->backlight.enabled = panel->backlight.level != 0; + + if (panel->backlight.edp.vesa.info.aux_set) { + panel->backlight.max = panel->backlight.edp.vesa.info.max; + panel->backlight.min = 0; + if (current_mode == DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) { + panel->backlight.level = current_level; + panel->backlight.enabled = panel->backlight.level != 0; + } else { + panel->backlight.level = panel->backlight.max; + panel->backlight.enabled = false; + } } else { - panel->backlight.level = panel->backlight.max; - panel->backlight.enabled = false; + panel->backlight.max = panel->backlight.pwm_level_max; + panel->backlight.min = panel->backlight.pwm_level_min; + if (current_mode == DP_EDP_BACKLIGHT_CONTROL_MODE_PWM) { + panel->backlight.level = panel->backlight.pwm_funcs->get(connector, pipe); + panel->backlight.enabled = panel->backlight.pwm_enabled; + } else { + panel->backlight.level = panel->backlight.max; + panel->backlight.enabled = false; + } } return 0; diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h index afdf7f4183f9..8b2ed4199284 100644 --- a/include/drm/drm_dp_helper.h +++ b/include/drm/drm_dp_helper.h @@ -1868,7 +1868,7 @@ drm_dp_sink_can_do_video_without_timing_msa(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) * * Note that currently this function will return %false for panels which support various DPCD * backlight features but which require the brightness be set through PWM, and don't support setting - * the brightness level via the DPCD. This is a TODO. + * the brightness level via the DPCD. * * Returns: %True if @edp_dpcd indicates that VESA backlight controls are supported, %false * otherwise @@ -1876,8 +1876,7 @@ drm_dp_sink_can_do_video_without_timing_msa(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) static inline bool drm_edp_backlight_supported(const u8 edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE]) { - return (edp_dpcd[1] & DP_EDP_TCON_BACKLIGHT_ADJUSTMENT_CAP) && - (edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_AUX_SET_CAP); + return !!(edp_dpcd[1] & DP_EDP_TCON_BACKLIGHT_ADJUSTMENT_CAP); } /* @@ -2238,6 +2237,7 @@ drm_dp_has_quirk(const struct drm_dp_desc *desc, enum drm_dp_quirk quirk) * @max: The maximum backlight level that may be set * @lsb_reg_used: Do we also write values to the DP_EDP_BACKLIGHT_BRIGHTNESS_LSB register? * @aux_enable: Does the panel support the AUX enable cap? + * @aux_set: Does the panel support setting the brightness through AUX? * * This structure contains various data about an eDP backlight, which can be populated by using * drm_edp_backlight_init(). @@ -2249,6 +2249,7 @@ struct drm_edp_backlight_info { bool lsb_reg_used : 1; bool aux_enable : 1; + bool aux_set : 1; }; int |