diff options
39 files changed, 4015 insertions, 291 deletions
diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index d733a428eff6..5ede7473b425 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -194,6 +194,48 @@ or, for backwards compatibility, the option value. E.g., The parameters are as follows: +ad_select + + Specifies the 802.3ad aggregation selection logic to use. The + possible values and their effects are: + + stable or 0 + + The active aggregator is chosen by largest aggregate + bandwidth. + + Reselection of the active aggregator occurs only when all + slaves of the active aggregator are down or the active + aggregator has no slaves. + + This is the default value. + + bandwidth or 1 + + The active aggregator is chosen by largest aggregate + bandwidth. Reselection occurs if: + + - A slave is added to or removed from the bond + + - Any slave's link state changes + + - Any slave's 802.3ad association state changes + + - The bond's adminstrative state changes to up + + count or 2 + + The active aggregator is chosen by the largest number of + ports (slaves). Reselection occurs as described under the + "bandwidth" setting, above. + + The bandwidth and count selection policies permit failover of + 802.3ad aggregations when partial failure of the active aggregator + occurs. This keeps the aggregator with the highest availability + (either in bandwidth or in number of ports) active at all times. + + This option was added in bonding version 3.4.0. + arp_interval Specifies the ARP link monitoring frequency in milliseconds. @@ -551,6 +593,16 @@ num_grat_arp affects only the active-backup mode. This option was added for bonding version 3.3.0. +num_unsol_na + + Specifies the number of unsolicited IPv6 Neighbor Advertisements + to be issued after a failover event. One unsolicited NA is issued + immediately after the failover. + + The valid range is 0 - 255; the default value is 1. This option + affects only the active-backup mode. This option was added for + bonding version 3.4.0. + primary A string (eth0, eth2, etc) specifying which slave is the diff --git a/MAINTAINERS b/MAINTAINERS index ca96939b7969..425e50e6b4c5 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3853,6 +3853,12 @@ M: mhoffman@lightlink.com L: lm-sensors@lm-sensors.org S: Maintained +SMSC911x ETHERNET DRIVER +P: Steve Glendinning +M: steve.glendinning@smsc.com +L: netdev@vger.kernel.org +S: Supported + SMX UIO Interface P: Ben Nizette M: bn@niasdigital.com diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 1757bb3f6e08..732ea834d50d 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -61,6 +61,7 @@ config DUMMY config BONDING tristate "Bonding driver support" depends on INET + depends on IPV6 || IPV6=n ---help--- Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet Channels together. This is called 'Etherchannel' by Cisco, @@ -978,6 +979,20 @@ config SMC911X called smc911x. If you want to compile it as a module, say M here and read <file:Documentation/kbuild/modules.txt> +config SMSC911X + tristate "SMSC LAN911x/LAN921x families embedded ethernet support" + depends on ARM || SUPERH + select CRC32 + select MII + select PHYLIB + ---help--- + Say Y here if you want support for SMSC LAN911x and LAN921x families + of ethernet controllers. + + To compile this driver as a module, choose M here and read + <file:Documentation/networking/net-modules.txt>. The module + will be called smsc911x. + config NET_VENDOR_RACAL bool "Racal-Interlan (Micom) NI cards" depends on ISA diff --git a/drivers/net/Makefile b/drivers/net/Makefile index 657c47b1a6b6..e06829aa75b0 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -219,6 +219,7 @@ obj-$(CONFIG_S2IO) += s2io.o obj-$(CONFIG_MYRI10GE) += myri10ge/ obj-$(CONFIG_SMC91X) += smc91x.o obj-$(CONFIG_SMC911X) += smc911x.o +obj-$(CONFIG_SMSC911X) += smsc911x.o obj-$(CONFIG_BFIN_MAC) += bfin_mac.o obj-$(CONFIG_DM9000) += dm9000.o obj-$(CONFIG_PASEMI_MAC) += pasemi_mac_driver.o diff --git a/drivers/net/bonding/Makefile b/drivers/net/bonding/Makefile index 5cdae2bc055a..6f9c6faef24c 100644 --- a/drivers/net/bonding/Makefile +++ b/drivers/net/bonding/Makefile @@ -6,3 +6,6 @@ obj-$(CONFIG_BONDING) += bonding.o bonding-objs := bond_main.o bond_3ad.o bond_alb.o bond_sysfs.o +ipv6-$(subst m,y,$(CONFIG_IPV6)) += bond_ipv6.o +bonding-objs += $(ipv6-y) + diff --git a/drivers/net/bonding/bond_3ad.c b/drivers/net/bonding/bond_3ad.c index 6106660a4a44..ba1372f2f144 100644 --- a/drivers/net/bonding/bond_3ad.c +++ b/drivers/net/bonding/bond_3ad.c @@ -27,6 +27,7 @@ #include <linux/netdevice.h> #include <linux/spinlock.h> #include <linux/ethtool.h> +#include <linux/etherdevice.h> #include <linux/if_bonding.h> #include <linux/pkt_sched.h> #include <net/net_namespace.h> @@ -236,6 +237,17 @@ static inline struct aggregator *__get_next_agg(struct aggregator *aggregator) return &(SLAVE_AD_INFO(slave->next).aggregator); } +/* + * __agg_has_partner + * + * Return nonzero if aggregator has a partner (denoted by a non-zero ether + * address for the partner). Return 0 if not. + */ +static inline int __agg_has_partner(struct aggregator *agg) +{ + return !is_zero_ether_addr(agg->partner_system.mac_addr_value); +} + /** * __disable_port - disable the port's slave * @port: the port we're looking at @@ -274,14 +286,14 @@ static inline int __port_is_enabled(struct port *port) * __get_agg_selection_mode - get the aggregator selection mode * @port: the port we're looking at * - * Get the aggregator selection mode. Can be %BANDWIDTH or %COUNT. + * Get the aggregator selection mode. Can be %STABLE, %BANDWIDTH or %COUNT. */ static inline u32 __get_agg_selection_mode(struct port *port) { struct bonding *bond = __get_bond_by_port(port); if (bond == NULL) { - return AD_BANDWIDTH; + return BOND_AD_STABLE; } return BOND_AD_INFO(bond).agg_select_mode; @@ -1414,9 +1426,82 @@ static void ad_port_selection_logic(struct port *port) // else set ready=FALSE in all aggregator's ports __set_agg_ports_ready(port->aggregator, __agg_ports_are_ready(port->aggregator)); - if (!__check_agg_selection_timer(port) && (aggregator = __get_first_agg(port))) { - ad_agg_selection_logic(aggregator); + aggregator = __get_first_agg(port); + ad_agg_selection_logic(aggregator); +} + +/* + * Decide if "agg" is a better choice for the new active aggregator that + * the current best, according to the ad_select policy. + */ +static struct aggregator *ad_agg_selection_test(struct aggregator *best, + struct aggregator *curr) +{ + /* + * 0. If no best, select current. + * + * 1. If the current agg is not individual, and the best is + * individual, select current. + * + * 2. If current agg is individual and the best is not, keep best. + * + * 3. Therefore, current and best are both individual or both not + * individual, so: + * + * 3a. If current agg partner replied, and best agg partner did not, + * select current. + * + * 3b. If current agg partner did not reply and best agg partner + * did reply, keep best. + * + * 4. Therefore, current and best both have partner replies or + * both do not, so perform selection policy: + * + * BOND_AD_COUNT: Select by count of ports. If count is equal, + * select by bandwidth. + * + * BOND_AD_STABLE, BOND_AD_BANDWIDTH: Select by bandwidth. + */ + if (!best) + return curr; + + if (!curr->is_individual && best->is_individual) + return curr; + + if (curr->is_individual && !best->is_individual) + return best; + + if (__agg_has_partner(curr) && !__agg_has_partner(best)) + return curr; + + if (!__agg_has_partner(curr) && __agg_has_partner(best)) + return best; + + switch (__get_agg_selection_mode(curr->lag_ports)) { + case BOND_AD_COUNT: + if (curr->num_of_ports > best->num_of_ports) + return curr; + + if (curr->num_of_ports < best->num_of_ports) + return best; + + /*FALLTHROUGH*/ + case BOND_AD_STABLE: + case BOND_AD_BANDWIDTH: + if (__get_agg_bandwidth(curr) > __get_agg_bandwidth(best)) + return curr; + + break; + + default: + printk(KERN_WARNING DRV_NAME + ": %s: Impossible agg select mode %d\n", + curr->slave->dev->master->name, + __get_agg_selection_mode(curr->lag_ports)); + break; } + + return best; } /** @@ -1424,156 +1509,138 @@ static void ad_port_selection_logic(struct port *port) * @aggregator: the aggregator we're looking at * * It is assumed that only one aggregator may be selected for a team. - * The logic of this function is to select (at first time) the aggregator with - * the most ports attached to it, and to reselect the active aggregator only if - * the previous aggregator has no more ports related to it. + * + * The logic of this function is to select the aggregator according to + * the ad_select policy: + * + * BOND_AD_STABLE: select the aggregator with the most ports attached to + * it, and to reselect the active aggregator only if the previous + * aggregator has no more ports related to it. + * + * BOND_AD_BANDWIDTH: select the aggregator with the highest total + * bandwidth, and reselect whenever a link state change takes place or the + * set of slaves in the bond changes. + * + * BOND_AD_COUNT: select the aggregator with largest number of ports + * (slaves), and reselect whenever a link state change takes place or the + * set of slaves in the bond changes. * * FIXME: this function MUST be called with the first agg in the bond, or * __get_active_agg() won't work correctly. This function should be better * called with the bond itself, and retrieve the first agg from it. */ -static void ad_agg_selection_logic(struct aggregator *aggregator) +static void ad_agg_selection_logic(struct aggregator *agg) { - struct aggregator *best_aggregator = NULL, *active_aggregator = NULL; - struct aggregator *last_active_aggregator = NULL, *origin_aggregator; + struct aggregator *best, *active, *origin; struct port *port; - u16 num_of_aggs=0; - origin_aggregator = aggregator; + origin = agg; - //get current active aggregator - last_active_aggregator = __get_active_agg(aggregator); + active = __get_active_agg(agg); + best = active; - // search for the aggregator with the most ports attached to it. do { - // count how many candidate lag's we have - if (aggregator->lag_ports) { - num_of_aggs++; - } - if (aggregator->is_active && !aggregator->is_individual && // if current aggregator is the active aggregator - MAC_ADDRESS_COMPARE(&(aggregator->partner_system), &(null_mac_addr))) { // and partner answers to 802.3ad PDUs - if (aggregator->num_of_ports) { // if any ports attached to the current aggregator - best_aggregator=NULL; // disregard the best aggregator that was chosen by now - break; // stop the selection of other aggregator if there are any ports attached to this active aggregator - } else { // no ports attached to this active aggregator - aggregator->is_active = 0; // mark this aggregator as not active anymore + agg->is_active = 0; + + if (agg->num_of_ports) + best = ad_agg_selection_test(best, agg); + + } while ((agg = __get_next_agg(agg))); + + if (best && + __get_agg_selection_mode(best->lag_ports) == BOND_AD_STABLE) { + /* + * For the STABLE policy, don't replace the old active + * aggregator if it's still active (it has an answering + * partner) or if both the best and active don't have an + * answering partner. + */ + if (active && active->lag_ports && + active->lag_ports->is_enabled && + (__agg_has_partner(active) || + (!__agg_has_partner(active) && !__agg_has_partner(best)))) { + if (!(!active->actor_oper_aggregator_key && + best->actor_oper_aggregator_key)) { + best = NULL; + active->is_active = 1; } } - if (aggregator->num_of_ports) { // if any ports attached - if (best_aggregator) { // if there is a candidte aggregator - //The reasons for choosing new best aggregator: - // 1. if current agg is NOT individual and the best agg chosen so far is individual OR - // current and best aggs are both individual or both not individual, AND - // 2a. current agg partner reply but best agg partner do not reply OR - // 2b. current agg partner reply OR current agg partner do not reply AND best agg partner also do not reply AND - // current has more ports/bandwidth, or same amount of ports but current has faster ports, THEN - // current agg become best agg so far - - //if current agg is NOT individual and the best agg chosen so far is individual change best_aggregator - if (!aggregator->is_individual && best_aggregator->is_individual) { - best_aggregator=aggregator; - } - // current and best aggs are both individual or both not individual - else if ((aggregator->is_individual && best_aggregator->is_individual) || - (!aggregator->is_individual && !best_aggregator->is_individual)) { - // current and best aggs are both individual or both not individual AND - // current agg partner reply but best agg partner do not reply - if ((MAC_ADDRESS_COMPARE(&(aggregator->partner_system), &(null_mac_addr)) && - !MAC_ADDRESS_COMPARE(&(best_aggregator->partner_system), &(null_mac_addr)))) { - best_aggregator=aggregator; - } - // current agg partner reply OR current agg partner do not reply AND best agg partner also do not reply - else if (! (!MAC_ADDRESS_COMPARE(&(aggregator->partner_system), &(null_mac_addr)) && - MAC_ADDRESS_COMPARE(&(best_aggregator->partner_system), &(null_mac_addr)))) { - if ((__get_agg_selection_mode(aggregator->lag_ports) == AD_BANDWIDTH)&& - (__get_agg_bandwidth(aggregator) > __get_agg_bandwidth(best_aggregator))) { - best_aggregator=aggregator; - } else if (__get_agg_selection_mode(aggregator->lag_ports) == AD_COUNT) { - if (((aggregator->num_of_ports > best_aggregator->num_of_ports) && - (aggregator->actor_oper_aggregator_key & AD_SPEED_KEY_BITS))|| - ((aggregator->num_of_ports == best_aggregator->num_of_ports) && - ((u16)(aggregator->actor_oper_aggregator_key & AD_SPEED_KEY_BITS) > - (u16)(best_aggregator->actor_oper_aggregator_key & AD_SPEED_KEY_BITS)))) { - best_aggregator=aggregator; - } - } - } - } - } else { - best_aggregator=aggregator; - } - } - aggregator->is_active = 0; // mark all aggregators as not active anymore - } while ((aggregator = __get_next_agg(aggregator))); - - // if we have new aggregator selected, don't replace the old aggregator if it has an answering partner, - // or if both old aggregator and new aggregator don't have answering partner - if (best_aggregator) { - if (last_active_aggregator && last_active_aggregator->lag_ports && last_active_aggregator->lag_ports->is_enabled && - (MAC_ADDRESS_COMPARE(&(last_active_aggregator->partner_system), &(null_mac_addr)) || // partner answers OR - (!MAC_ADDRESS_COMPARE(&(last_active_aggregator->partner_system), &(null_mac_addr)) && // both old and new - !MAC_ADDRESS_COMPARE(&(best_aggregator->partner_system), &(null_mac_addr)))) // partner do not answer - ) { - // if new aggregator has link, and old aggregator does not, replace old aggregator.(do nothing) - // -> don't replace otherwise. - if (!(!last_active_aggregator->actor_oper_aggregator_key && best_aggregator->actor_oper_aggregator_key)) { - best_aggregator=NULL; - last_active_aggregator->is_active = 1; // don't replace good old aggregator + } - } - } + if (best && (best == active)) { + best = NULL; + active->is_active = 1; } // if there is new best aggregator, activate it - if (best_aggregator) { - for (aggregator = __get_first_agg(best_aggregator->lag_ports); - aggregator; - aggregator = __get_next_agg(aggregator)) { - - dprintk("Agg=%d; Ports=%d; a key=%d; p key=%d; Indiv=%d; Active=%d\n", - aggregator->aggregator_identifier, aggregator->num_of_ports, - aggregator->actor_oper_aggregator_key, aggregator->partner_oper_aggregator_key, - aggregator->is_individual, aggregator->is_active); + if (best) { + dprintk("best Agg=%d; P=%d; a k=%d; p k=%d; Ind=%d; Act=%d\n", + best->aggregator_identifier, best->num_of_ports, + best->actor_oper_aggregator_key, + best->partner_oper_aggregator_key, + best->is_individual, best->is_active); + dprintk("best ports %p slave %p %s\n", + best->lag_ports, best->slave, + best->slave ? best->slave->dev->name : "NULL"); + + for (agg = __get_first_agg(best->lag_ports); agg; + agg = __get_next_agg(agg)) { + + dprintk("Agg=%d; P=%d; a k=%d; p k=%d; Ind=%d; Act=%d\n", + agg->aggregator_identifier, agg->num_of_ports, + agg->actor_oper_aggregator_key, + agg->partner_oper_aggregator_key, + agg->is_individual, agg->is_active); } // check if any partner replys - if (best_aggregator->is_individual) { - printk(KERN_WARNING DRV_NAME ": %s: Warning: No 802.3ad response from " - "the link partner for any adapters in the bond\n", - best_aggregator->slave->dev->master->name); - } - - // check if there are more than one aggregator - if (num_of_aggs > 1) { - dprintk("Warning: More than one Link Aggregation Group was " - "found in the bond. Only one group will function in the bond\n"); + if (best->is_individual) { + printk(KERN_WARNING DRV_NAME ": %s: Warning: No 802.3ad" + " response from the link partner for any" + " adapters in the bond\n", + best->slave->dev->master->name); } - best_aggregator->is_active = 1; - dprintk("LAG %d choosed as the active LAG\n", best_aggregator->aggregator_identifier); - dprintk("Agg=%d; Ports=%d; a key=%d; p key=%d; Indiv=%d; Active=%d\n", - best_aggregator->aggregator_identifier, best_aggregator->num_of_ports, - best_aggregator->actor_oper_aggregator_key, best_aggregator->partner_oper_aggregator_key, - best_aggregator->is_individual, best_aggregator->is_active); + best->is_active = 1; + dprintk("LAG %d chosen as the active LAG\n", + best->aggregator_identifier); + dprintk("Agg=%d; P=%d; a k=%d; p k=%d; Ind=%d; Act=%d\n", + best->aggregator_identifier, best->num_of_ports, + best->actor_oper_aggregator_key, + best->partner_oper_aggregator_key, + best->is_individual, best->is_active); // disable the ports that were related to the former active_aggregator - if (last_active_aggregator) { - for (port=last_active_aggregator->lag_ports; port; port=port->next_port_in_aggregator) { + if (active) { + for (port = active->lag_ports; port; + port = port->next_port_in_aggregator) { __disable_port(port); } } } - // if the selected aggregator is of join individuals(partner_system is NULL), enable their ports - active_aggregator = __get_active_agg(origin_aggregator); + /* + * if the selected aggregator is of join individuals + * (partner_system is NULL), enable their ports + */ + active = __get_active_agg(origin); - if (active_aggregator) { - if (!MAC_ADDRESS_COMPARE(&(active_aggregator->partner_system), &(null_mac_addr))) { - for (port=active_aggregator->lag_ports; port; port=port->next_port_in_aggregator) { + if (active) { + if (!__agg_has_partner(active)) { + for (port = active->lag_ports; port; + port = port->next_port_in_aggregator) { __enable_port(port); } } } + + if (origin->slave) { + struct bonding *bond; + + bond = bond_get_bond_by_slave(origin->slave); + if (bond) + bond_3ad_set_carrier(bond); + } } /** @@ -1830,6 +1897,19 @@ static void ad_initialize_lacpdu(struct lacpdu *lacpdu) // Check aggregators status in team every T seconds #define AD_AGGREGATOR_SELECTION_TIMER 8 +/* + * bond_3ad_initiate_agg_selection(struct bonding *bond) + * + * Set the aggregation selection timer, to initiate an agg selection in + * the very near future. Called during first initialization, and during + * any down to up transitions of the bond. + */ +void bond_3ad_initiate_agg_selection(struct bonding *bond, int timeout) +{ + BOND_AD_INFO(bond).agg_select_timer = timeout; + BOND_AD_INFO(bond).agg_select_mode = bond->params.ad_select; +} + static u16 aggregator_identifier; /** @@ -1854,9 +1934,9 @@ void bond_3ad_initialize(struct bonding *bond, u16 tick_resolution, int lacp_fas // initialize how many times this module is called in one second(should be about every 100ms) ad_ticks_per_sec = tick_resolution; - // initialize the aggregator selection timer(to activate an aggregation selection after initialize) - BOND_AD_INFO(bond).agg_select_timer = (AD_AGGREGATOR_SELECTION_TIMER * ad_ticks_per_sec); - BOND_AD_INFO(bond).agg_select_mode = AD_BANDWIDTH; + bond_3ad_initiate_agg_selection(bond, + AD_AGGREGATOR_SELECTION_TIMER * + ad_ticks_per_sec); } } diff --git a/drivers/net/bonding/bond_3ad.h b/drivers/net/bonding/bond_3ad.h index b5ee45f6d55a..a803fe05f63e 100644 --- a/drivers/net/bonding/bond_3ad.h +++ b/drivers/net/bonding/bond_3ad.h @@ -42,10 +42,11 @@ typedef struct mac_addr { u8 mac_addr_value[ETH_ALEN]; } mac_addr_t; -typedef enum { - AD_BANDWIDTH = 0, - AD_COUNT -} agg_selection_t; +enum { + BOND_AD_STABLE = 0, + BOND_AD_BANDWIDTH = 1, + BOND_AD_COUNT = 2, +}; // rx machine states(43.4.11 in the 802.3ad standard) typedef enum { @@ -277,6 +278,7 @@ void bond_3ad_initialize(struct bonding *bond, u16 tick_resolution, int lacp_fas int bond_3ad_bind_slave(struct slave *slave); void bond_3ad_unbind_slave(struct slave *slave); void bond_3ad_state_machine_handler(struct work_struct *); +void bond_3ad_initiate_agg_selection(struct bonding *bond, int timeout); void bond_3ad_adapter_speed_changed(struct slave *slave); void bond_3ad_adapter_duplex_changed(struct slave *slave); void bond_3ad_handle_link_change(struct slave *slave, char link); diff --git a/drivers/net/bonding/bond_alb.c b/drivers/net/bonding/bond_alb.c index 87437c788476..e170fa2fa1a1 100644 --- a/drivers/net/bonding/bond_alb.c +++ b/drivers/net/bonding/bond_alb.c @@ -346,14 +346,18 @@ static void rlb_update_entry_from_arp(struct bonding *bond, struct arp_pkt *arp) static int rlb_arp_recv(struct sk_buff *skb, struct net_device *bond_dev, struct packet_type *ptype, struct net_device *orig_dev) { - struct bonding *bond = bond_dev->priv; + struct bonding *bond; struct arp_pkt *arp = (struct arp_pkt *)skb->data; int res = NET_RX_DROP; if (dev_net(bond_dev) != &init_net) goto out; - if (!(bond_dev->flags & IFF_MASTER)) + while (bond_dev->priv_flags & IFF_802_1Q_VLAN) + bond_dev = vlan_dev_real_dev(bond_dev); + + if (!(bond_dev->priv_flags & IFF_BONDING) || + !(bond_dev->flags & IFF_MASTER)) goto out; if (!arp) { @@ -368,6 +372,9 @@ static int rlb_arp_recv(struct sk_buff *skb, struct net_device *bond_dev, struct if (arp->op_code == htons(ARPOP_REPLY)) { /* update rx hash table for this ARP */ + printk("rar: update orig %s bond_dev %s\n", orig_dev->name, + bond_dev->name); + bond = bond_dev->priv; rlb_update_entry_from_arp(bond, arp); dprintk("Server received an ARP Reply from client\n"); } @@ -818,7 +825,7 @@ static int rlb_initialize(struct bonding *bond) /*initialize packet type*/ pk_type->type = __constant_htons(ETH_P_ARP); - pk_type->dev = bond->dev; + pk_type->dev = NULL; pk_type->func = rlb_arp_recv; /* register to receive ARPs */ diff --git a/drivers/net/bonding/bond_ipv6.c b/drivers/net/bonding/bond_ipv6.c new file mode 100644 index 000000000000..7c78b7bf671c --- /dev/null +++ b/drivers/net/bonding/bond_ipv6.c @@ -0,0 +1,218 @@ +/* + * Copyright(c) 2008 Hewlett-Packard Development Company, L.P. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY + * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * + * The full GNU General Public License is included in this distribution in the + * file called LICENSE. + * + */ + +//#define BONDING_DEBUG 1 + +#include <linux/types.h> +#include <linux/if_vlan.h> +#include <net/ipv6.h> +#include <net/ndisc.h> +#include <net/addrconf.h> +#include "bonding.h" + +/* + * Assign bond->master_ipv6 to the next IPv6 address in the list, or + * zero it out if there are none. + */ +static void bond_glean_dev_ipv6(struct net_device *dev, struct in6_addr *addr) +{ + struct inet6_dev *idev; + struct inet6_ifaddr *ifa; + + if (!dev) + return; + + idev = in6_dev_get(dev); + if (!idev) + return; + + read_lock_bh(&idev->lock); + ifa = idev->addr_list; + if (ifa) + ipv6_addr_copy(addr, &ifa->addr); + else + ipv6_addr_set(addr, 0, 0, 0, 0); + + read_unlock_bh(&idev->lock); + + in6_dev_put(idev); +} + +static void bond_na_send(struct net_device *slave_dev, + struct in6_addr *daddr, + int router, + unsigned short vlan_id) +{ + struct in6_addr mcaddr; + struct icmp6hdr icmp6h = { + .icmp6_type = NDISC_NEIGHBOUR_ADVERTISEMENT, + }; + struct sk_buff *skb; + + icmp6h.icmp6_router = router; + icmp6h.icmp6_solicited = 0; + icmp6h.icmp6_override = 1; + + addrconf_addr_solict_mult(daddr, &mcaddr); + + dprintk("ipv6 na on slave %s: dest %pI6, src %pI6\n", + slave->name, &mcaddr, daddr); + + skb = ndisc_build_skb(slave_dev, &mcaddr, daddr, &icmp6h, daddr, + ND_OPT_TARGET_LL_ADDR); + + if (!skb) { + printk(KERN_ERR DRV_NAME ": NA packet allocation failed\n"); + return; + } + + if (vlan_id) { + skb = vlan_put_tag(skb, vlan_id); + if (!skb) { + printk(KERN_ERR DRV_NAME ": failed to insert VLAN tag\n"); + return; + } + } + + ndisc_send_skb(skb, slave_dev, NULL, &mcaddr, daddr, &icmp6h); +} + +/* + * Kick out an unsolicited Neighbor Advertisement for an IPv6 address on + * the bonding master. This will help the switch learn our address + * if in active-backup mode. + * + * Caller must hold curr_slave_lock for read or better + */ +void bond_send_unsolicited_na(struct bonding *bond) +{ + struct slave *slave = bond->curr_active_slave; + struct vlan_entry *vlan; + struct inet6_dev *idev; + int is_router; + + dprintk("bond_send_unsol_na: bond %s slave %s\n", bond->dev->name, + slave ? slave->dev->name : "NULL"); + + if (!slave || !bond->send_unsol_na || + test_bit(__LINK_STATE_LINKWATCH_PENDING, &slave->dev->state)) + return; + + bond->send_unsol_na--; + + idev = in6_dev_get(bond->dev); + if (!idev) + return; + + is_router = !!idev->cnf.forwarding; + + in6_dev_put(idev); + + if (!ipv6_addr_any(&bond->master_ipv6)) + bond_na_send(slave->dev, &bond->master_ipv6, is_router, 0); + + list_for_each_entry(vlan, &bond->vlan_list, vlan_list) { + if (!ipv6_addr_any(&vlan->vlan_ipv6)) { + bond_na_send(slave->dev, &vlan->vlan_ipv6, is_router, + vlan->vlan_id); + } + } +} + +/* + * bond_inet6addr_event: handle inet6addr notifier chain events. + * + * We keep track of device IPv6 addresses primarily to use as source + * addresses in NS probes. + * + * We track one IPv6 for the main device (if it has one). + */ +static int bond_inet6addr_event(struct notifier_block *this, + unsigned long event, + void *ptr) +{ + struct inet6_ifaddr *ifa = ptr; + struct net_device *vlan_dev, *event_dev = ifa->idev->dev; + struct bonding *bond; + struct vlan_entry *vlan; + + if (dev_net(event_dev) != &init_net) + return NOTIFY_DONE; + + list_for_each_entry(bond, &bond_dev_list, bond_list) { + if (bond->dev == event_dev) { + switch (event) { + case NETDEV_UP: + if (ipv6_addr_any(&bond->master_ipv6)) + ipv6_addr_copy(&bond->master_ipv6, + &ifa->addr); + return NOTIFY_OK; + case NETDEV_DOWN: + if (ipv6_addr_equal(&bond->master_ipv6, + &ifa->addr)) + bond_glean_dev_ipv6(bond->dev, + &bond->master_ipv6); + return NOTIFY_OK; + default: + return NOTIFY_DONE; + } + } + + list_for_each_entry(vlan, &bond->vlan_list, vlan_list) { + vlan_dev = vlan_group_get_device(bond->vlgrp, + vlan->vlan_id); + if (vlan_dev == event_dev) { + switch (event) { + case NETDEV_UP: + if (ipv6_addr_any(&vlan->vlan_ipv6)) + ipv6_addr_copy(&vlan->vlan_ipv6, + &ifa->addr); + return NOTIFY_OK; + case NETDEV_DOWN: + if (ipv6_addr_equal(&vlan->vlan_ipv6, + &ifa->addr)) + bond_glean_dev_ipv6(vlan_dev, + &vlan->vlan_ipv6); + return NOTIFY_OK; + default: + return NOTIFY_DONE; + } + } + } + } + return NOTIFY_DONE; +} + +static struct notifier_block bond_inet6addr_notifier = { + .notifier_call = bond_inet6addr_event, +}; + +void bond_register_ipv6_notifier(void) +{ + register_inet6addr_notifier(&bond_inet6addr_notifier); +} + +void bond_unregister_ipv6_notifier(void) +{ + unregister_inet6addr_notifier(&bond_inet6addr_notifier); +} + diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index 39575d764974..02de3e031237 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -89,6 +89,7 @@ static int max_bonds = BOND_DEFAULT_MAX_BONDS; static int num_grat_arp = 1; +static int num_unsol_na = 1; static int miimon = BOND_LINK_MON_INTERV; static int updelay = 0; static int downdelay = 0; @@ -96,6 +97,7 @@ static int use_carrier = 1; static char *mode = NULL; static char *primary = NULL; static char *lacp_rate = NULL; +static char *ad_select = NULL; static char *xmit_hash_policy = NULL; static int arp_interval = BOND_LINK_ARP_INTERV; static char *arp_ip_target[BOND_MAX_ARP_TARGETS] = { NULL, }; @@ -107,6 +109,8 @@ module_param(max_bonds, int, 0); MODULE_PARM_DESC(max_bonds, "Max number of bonded devices"); module_param(num_grat_arp, int, 0644); MODULE_PARM_DESC(num_grat_arp, "Number of gratuitous ARP packets to send on failover event"); +module_param(num_unsol_na, int, 0644); +MODULE_PARM_DESC(num_unsol_na, "Number of unsolicited IPv6 Neighbor Advertisements packets to send on failover event"); module_param(miimon, int, 0); MODULE_PARM_DESC(miimon, "Link check interval in milliseconds"); module_param(updelay, int, 0); @@ -127,6 +131,8 @@ MODULE_PARM_DESC(primary, "Primary network device to use"); module_param(lacp_rate, charp, 0); MODULE_PARM_DESC(lacp_rate, "LACPDU tx rate to request from 802.3ad partner " "(slow/fast)"); +module_param(ad_select, charp, 0); +MODULE_PARM_DESC(ad_select, "803.ad aggregation selection logic: stable (0, default), bandwidth (1), count (2)"); module_param(xmit_hash_policy, charp, 0); MODULE_PARM_DESC(xmit_hash_policy, "XOR hashing method: 0 for layer 2 (default)" ", 1 for layer 3+4"); @@ -197,6 +203,13 @@ struct bond_parm_tbl fail_over_mac_tbl[] = { { NULL, -1}, }; +struct bond_parm_tbl ad_select_tbl[] = { +{ "stable", BOND_AD_STABLE}, +{ "bandwidth", BOND_AD_BANDWIDTH}, +{ "count", BOND_AD_COUNT}, +{ NULL, -1}, +}; + /*-------------------------- Forward declarations ---------------------------*/ static void bond_send_gratuitous_arp(struct bonding *bond); @@ -242,14 +255,13 @@ static int bond_add_vlan(struct bonding *bond, unsigned short vlan_id) dprintk("bond: %s, vlan id %d\n", (bond ? bond->dev->name: "None"), vlan_id); - vlan = kmalloc(sizeof(struct vlan_entry), GFP_KERNEL); + vlan = kzalloc(sizeof(struct vlan_entry), GFP_KERNEL); if (!vlan) { return -ENOMEM; } INIT_LIST_HEAD(&vlan->vlan_list); vlan->vlan_id = vlan_id; - vlan->vlan_ip = 0; write_lock_bh(&bond->lock); @@ -1208,6 +1220,9 @@ void bond_change_active_slave(struct bonding *bond, struct slave *new_active) bond->send_grat_arp = bond->params.num_grat_arp; bond_send_gratuitous_arp(bond); + bond->send_unsol_na = bond->params.num_unsol_na; + bond_send_unsolicited_na(bond); + write_unlock_bh(&bond->curr_slave_lock); read_unlock(&bond->lock); @@ -2463,6 +2478,12 @@ void bond_mii_monitor(struct work_struct *work) read_unlock(&bond->curr_slave_lock); } + if (bond->send_unsol_na) { + read_lock(&bond->curr_slave_lock); + bond_send_unsolicited_na(bond); + read_unlock(&bond->curr_slave_lock); + } + if (bond_miimon_inspect(bond)) { read_unlock(&bond->lock); rtnl_lock(); @@ -3158,6 +3179,12 @@ void bond_activebackup_arp_mon(struct work_struct *work) read_unlock(&bond->curr_slave_lock); } + if (bond->send_unsol_na) { + read_lock(&bond->curr_slave_lock); + bond_send_unsolicited_na(bond); + read_unlock(&bond->curr_slave_lock); + } + if (bond_ab_arp_inspect(bond, delta_in_ticks)) { read_unlock(&bond->lock); rtnl_lock(); @@ -3301,6 +3328,8 @@ static void bond_info_show_master(struct seq_file *seq) seq_puts(seq, "\n802.3ad info\n"); seq_printf(seq, "LACP rate: %s\n", (bond->params.lacp_fast) ? "fast" : "slow"); + seq_printf(seq, "Aggregator selection policy (ad_select): %s\n", + ad_select_tbl[bond->params.ad_select].modename); if (bond_3ad_get_active_agg_info(bond, &ad_info)) { seq_printf(seq, "bond %s has no active aggregator\n", @@ -3807,6 +3836,7 @@ static int bond_open(struct net_device *bond_dev) queue_delayed_work(bond->wq, &bond->ad_work, 0); /* register to receive LACPDUs */ bond_register_lacpdu(bond); + bond_3ad_initiate_agg_selection(bond, 1); } return 0; @@ -3827,6 +3857,7 @@ static int bond_close(struct net_device *bond_dev) write_lock_bh(&bond->lock); bond->send_grat_arp = 0; + bond->send_unsol_na = 0; /* signal timers not to re-arm */ bond->kill_timers = 1; @@ -4542,6 +4573,7 @@ static int bond_init(struct net_device *bond_dev, struct bond_params *params) bond->primary_slave = NULL; bond->dev = bond_dev; bond->send_grat_arp = 0; + bond->send_unsol_na = 0; bond->setup_by_slave = 0; INIT_LIST_HEAD(&bond->vlan_list); @@ -4744,6 +4776,23 @@ static int bond_check_params(struct bond_params *params) } } + if (ad_select) { + params->ad_select = bond_parse_parm(ad_select, ad_select_tbl); + if (params->ad_select == -1) { + printk(KERN_ERR DRV_NAME + ": Error: Invalid ad_select \"%s\"\n", + ad_select == NULL ? "NULL" : ad_select); + return -EINVAL; + } + + if (bond_mode != BOND_MODE_8023AD) { + printk(KERN_WARNING DRV_NAME + ": ad_select param only affects 802.3ad mode\n"); + } + } else { + params->ad_select = BOND_AD_STABLE; + } + if (max_bonds < 0 || max_bonds > INT_MAX) { printk(KERN_WARNING DRV_NAME ": Warning: max_bonds (%d) not in range %d-%d, so it " @@ -4791,6 +4840,13 @@ static int bond_check_params(struct bond_params *params) num_grat_arp = 1; } + if (num_unsol_na < 0 || num_unsol_na > 255) { + printk(KERN_WARNING DRV_NAME + ": Warning: num_unsol_na (%d) not in range 0-255 so it " + "was reset to 1 \n", num_unsol_na); + num_unsol_na = 1; + } + /* reset values for 802.3ad */ if (bond_mode == BOND_MODE_8023AD) { if (!miimon) { @@ -4992,6 +5048,7 @@ static int bond_check_params(struct bond_params *params) params->xmit_policy = xmit_hashtype; params->miimon = miimon; params->num_grat_arp = num_grat_arp; + params->num_unsol_na = num_unsol_na; params->arp_interval = arp_interval; params->arp_validate = arp_validate_value; params->updelay = updelay; @@ -5144,6 +5201,7 @@ static int __init bonding_init(void) register_netdevice_notifier(&bond_netdev_notifier); register_inetaddr_notifier(&bond_inetaddr_notifier); + bond_register_ipv6_notifier(); goto out; err: @@ -5166,6 +5224,7 @@ static void __exit bonding_exit(void) { unregister_netdevice_notifier(&bond_netdev_notifier); unregister_inetaddr_notifier(&bond_inetaddr_notifier); + bond_unregister_ipv6_notifier(); bond_destroy_sysfs(); diff --git a/drivers/net/bonding/bond_sysfs.c b/drivers/net/bonding/bond_sysfs.c index e400d7dfdfc8..aaf2927b5c38 100644 --- a/drivers/net/bonding/bond_sysfs.c +++ b/drivers/net/bonding/bond_sysfs.c @@ -48,6 +48,7 @@ extern struct list_head bond_dev_list; extern struct bond_params bonding_defaults; extern struct bond_parm_tbl bond_mode_tbl[]; extern struct bond_parm_tbl bond_lacp_tbl[]; +extern struct bond_parm_tbl ad_select_tbl[]; extern struct bond_parm_tbl xmit_hashtype_tbl[]; extern struct bond_parm_tbl arp_validate_tbl[]; extern struct bond_parm_tbl fail_over_mac_tbl[]; @@ -944,6 +945,53 @@ out: } static DEVICE_ATTR(lacp_rate, S_IRUGO | S_IWUSR, bonding_show_lacp, bonding_store_lacp); +static ssize_t bonding_show_ad_select(struct device *d, + struct device_attribute *attr, + char *buf) +{ + struct bonding *bond = to_bond(d); + + return sprintf(buf, "%s %d\n", + ad_select_tbl[bond->params.ad_select].modename, + bond->params.ad_select); +} + + +static ssize_t bonding_store_ad_select(struct device *d, + struct device_attribute *attr, + const char *buf, size_t count) +{ + int new_value, ret = count; + struct bonding *bond = to_bond(d); + + if (bond->dev->flags & IFF_UP) { + printk(KERN_ERR DRV_NAME + ": %s: Unable to update ad_select because interface " + "is up.\n", bond->dev->name); + ret = -EPERM; + goto out; + } + + new_value = bond_parse_parm(buf, ad_select_tbl); + + if (new_value != -1) { + bond->params.ad_select = new_value; + printk(KERN_INFO DRV_NAME + ": %s: Setting ad_select to %s (%d).\n", + bond->dev->name, ad_select_tbl[new_value].modename, + new_value); + } else { + printk(KERN_ERR DRV_NAME + ": %s: Ignoring invalid ad_select value %.*s.\n", + bond->dev->name, (int)strlen(buf) - 1, buf); + ret = -EINVAL; + } +out: + return ret; +} + +static DEVICE_ATTR(ad_select, S_IRUGO | S_IWUSR, bonding_show_ad_select, bonding_store_ad_select); + /* * Show and set the number of grat ARP to send after a failover event. */ @@ -983,6 +1031,47 @@ out: return ret; } static DEVICE_ATTR(num_grat_arp, S_IRUGO | S_IWUSR, bonding_show_n_grat_arp, bonding_store_n_grat_arp); + +/* + * Show and set the number of unsolicted NA's to send after a failover event. + */ +static ssize_t bonding_show_n_unsol_na(struct device *d, + struct device_attribute *attr, + char *buf) +{ + struct bonding *bond = to_bond(d); + + return sprintf(buf, "%d\n", bond->params.num_unsol_na); +} + +static ssize_t bonding_store_n_unsol_na(struct device *d, + struct device_attribute *attr, + const char *buf, size_t count) +{ + int new_value, ret = count; + struct bonding *bond = to_bond(d); + + if (sscanf(buf, "%d", &new_value) != 1) { + printk(KERN_ERR DRV_NAME + ": %s: no num_unsol_na value specified.\n", + bond->dev->name); + ret = -EINVAL; + goto out; + } + if (new_value < 0 || new_value > 255) { + printk(KERN_ERR DRV_NAME + ": %s: Invalid num_unsol_na value %d not in range 0-255; rejected.\n", + bond->dev->name, new_value); + ret = -EINVAL; + goto out; + } else { + bond->params.num_unsol_na = new_value; + } +out: + return ret; +} +static DEVICE_ATTR(num_unsol_na, S_IRUGO | S_IWUSR, bonding_show_n_unsol_na, bonding_store_n_unsol_na); + /* * Show and set the MII monitor interval. There are two tricky bits * here. First, if MII monitoring is activated, then we must disable @@ -1418,8 +1507,10 @@ static struct attribute *per_bond_attrs[] = { &dev_attr_downdelay.attr, &dev_attr_updelay.attr, &dev_attr_lacp_rate.attr, + &dev_attr_ad_select.attr, &dev_attr_xmit_hash_policy.attr, &dev_attr_num_grat_arp.attr, + &dev_attr_num_unsol_na.attr, &dev_attr_miimon.attr, &dev_attr_primary.attr, &dev_attr_use_carrier.attr, diff --git a/drivers/net/bonding/bonding.h b/drivers/net/bonding/bonding.h index ffb668dd6d3b..b5eb8e65b309 100644 --- a/drivers/net/bonding/bonding.h +++ b/drivers/net/bonding/bonding.h @@ -19,16 +19,19 @@ #include <linux/proc_fs.h> #include <linux/if_bonding.h> #include <linux/kobject.h> +#include <linux/in6.h> #include "bond_3ad.h" #include "bond_alb.h" -#define DRV_VERSION "3.3.0" -#define DRV_RELDATE "June 10, 2008" +#define DRV_VERSION "3.5.0" +#define DRV_RELDATE "November 4, 2008" #define DRV_NAME "bonding" #define DRV_DESCRIPTION "Ethernet Channel Bonding Driver" #define BOND_MAX_ARP_TARGETS 16 +extern struct list_head bond_dev_list; + #ifdef BONDING_DEBUG #define dprintk(fmt, args...) \ printk(KERN_DEBUG \ @@ -126,6 +129,7 @@ struct bond_params { int xmit_policy; int miimon; int num_grat_arp; + int num_unsol_na; int arp_interval; int arp_validate; int use_carrier; @@ -133,6 +137,7 @@ struct bond_params { int updelay; int downdelay; int lacp_fast; + int ad_select; char primary[IFNAMSIZ]; __be32 arp_targets[BOND_MAX_ARP_TARGETS]; }; @@ -148,6 +153,9 @@ struct vlan_entry { struct list_head vlan_list; __be32 vlan_ip; unsigned short vlan_id; +#if defined(CONFIG_IPV6) || defined(CONFIG_IPV6_MODULE) + struct in6_addr vlan_ipv6; +#endif }; struct slave { @@ -195,6 +203,7 @@ struct bonding { rwlock_t curr_slave_lock; s8 kill_timers; s8 send_grat_arp; + s8 send_unsol_na; s8 setup_by_slave; struct net_device_stats stats; #ifdef CONFIG_PROC_FS @@ -218,6 +227,9 @@ struct bonding { struct delayed_work arp_work; struct delayed_work alb_work; struct delayed_work ad_work; +#if defined(CONFIG_IPV6) || defined(CONFIG_IPV6_MODULE) + struct in6_addr master_ipv6; +#endif }; /** @@ -341,5 +353,24 @@ extern struct bond_parm_tbl xmit_hashtype_tbl[]; extern struct bond_parm_tbl arp_validate_tbl[]; extern struct bond_parm_tbl fail_over_mac_tbl[]; +#if defined(CONFIG_IPV6) || defined(CONFIG_IPV6_MODULE) +void bond_send_unsolicited_na(struct bonding *bond); +void bond_register_ipv6_notifier(void); +void bond_unregister_ipv6_notifier(void); +#else +static inline void bond_send_unsolicited_na(struct bonding *bond) +{ + return; +} +static inline void bond_register_ipv6_notifier(void) +{ + return; +} +static inline void bond_unregister_ipv6_notifier(void) +{ + return; +} +#endif + #endif /* _LINUX_BONDING_H */ diff --git a/drivers/net/ehea/ehea.h b/drivers/net/ehea/ehea.h index 002d918fb4c7..9930d5f8b9e1 100644 --- a/drivers/net/ehea/ehea.h +++ b/drivers/net/ehea/ehea.h @@ -40,7 +40,7 @@ #include <asm/io.h> #define DRV_NAME "ehea" -#define DRV_VERSION "EHEA_0095" +#define DRV_VERSION "EHEA_0096" /* eHEA capability flags */ #define DLPAR_PORT_ADD_REM 1 diff --git a/drivers/net/ehea/ehea_qmr.c b/drivers/net/ehea/ehea_qmr.c index 9d006878f045..3c0ec82f36fb 100644 --- a/drivers/net/ehea/ehea_qmr.c +++ b/drivers/net/ehea/ehea_qmr.c @@ -653,7 +653,7 @@ static int ehea_update_busmap(unsigned long pfn, unsigned long nr_pages, int add int top = ehea_calc_index(i, EHEA_TOP_INDEX_SHIFT); int dir = ehea_calc_index(i, EHEA_DIR_INDEX_SHIFT); int idx = i & EHEA_INDEX_MASK; - + if (add) { int ret = ehea_init_bmap(ehea_bmap, top, dir); if (ret) @@ -780,7 +780,7 @@ void ehea_destroy_busmap(void) kfree(ehea_bmap); ehea_bmap = NULL; -out_destroy: +out_destroy: mutex_unlock(&ehea_busmap_mutex); } @@ -858,10 +858,10 @@ static u64 ehea_reg_mr_sections(int top, int dir, u64 *pt, for (idx = 0; idx < EHEA_MAP_ENTRIES; idx++) { if (!ehea_bmap->top[top]->dir[dir]->ent[idx]) continue; - + hret = ehea_reg_mr_section(top, dir, idx, pt, adapter, mr); if ((hret != H_SUCCESS) && (hret != H_PAGE_REGISTERED)) - return hret; + return hret; } return hret; } @@ -879,7 +879,7 @@ static u64 ehea_reg_mr_dir_sections(int top, u64 *pt, hret = ehea_reg_mr_sections(top, dir, pt, adapter, mr); if ((hret != H_SUCCESS) && (hret != H_PAGE_REGISTERED)) - return hret; + return hret; } return hret; } diff --git a/drivers/net/pcmcia/fmvj18x_cs.c b/drivers/net/pcmcia/fmvj18x_cs.c index e4f8fe3c5dae..69dcfbbabe82 100644 --- a/drivers/net/pcmcia/fmvj18x_cs.c +++ b/drivers/net/pcmcia/fmvj18x_cs.c @@ -125,6 +125,7 @@ typedef struct local_info_t { u_short tx_queue_len; cardtype_t cardtype; u_short sent; + u_char __iomem *base; } local_info_t; #define MC_FILTERBREAK 64 @@ -242,6 +243,7 @@ static int fmvj18x_probe(struct pcmcia_device *link) lp = netdev_priv(dev); link->priv = dev; lp->p_dev = link; + lp->base = NULL; /* The io structure describes IO port mapping */ link->io.NumPorts1 = 32; @@ -442,8 +444,10 @@ static int fmvj18x_config(struct pcmcia_device *link) dev->irq = link->irq.AssignedIRQ; dev->base_addr = link->io.BasePort1; - if (link->io.BasePort2 != 0) - fmvj18x_setup_mfc(link); + if (link->io.BasePort2 != 0) { + ret = fmvj18x_setup_mfc(link); + if (ret != 0) goto failed; + } ioaddr = dev->base_addr; @@ -610,10 +614,10 @@ static int fmvj18x_setup_mfc(struct pcmcia_device *link) { win_req_t req; memreq_t mem; - u_char __iomem *base; - int i, j; + int i; struct net_device *dev = link->priv; unsigned int ioaddr; + local_info_t *lp = netdev_priv(dev); /* Allocate a small memory window */ req.Attributes = WIN_DATA_WIDTH_8|WIN_MEMORY_TYPE_AM|WIN_ENABLE; @@ -625,25 +629,32 @@ static int fmvj18x_setup_mfc(struct pcmcia_device *link) return -1; } - base = ioremap(req.Base, req.Size); + lp->base = ioremap(req.Base, req.Size); + if (lp->base == NULL) { + printk(KERN_NOTICE "fmvj18x_cs: ioremap failed\n"); + return -1; + } + mem.Page = 0; mem.CardOffset = 0; - pcmcia_map_mem_page(link->win, &mem); - + i = pcmcia_map_mem_page(link->win, &mem); + if (i != 0) { + iounmap(lp->base); + lp->base = NULL; + cs_error(link, MapMemPage, i); + return -1; + } + ioaddr = dev->base_addr; - writeb(0x47, base+0x800); /* Config Option Register of LAN */ - writeb(0x0, base+0x802); /* Config and Status Register */ + writeb(0x47, lp->base+0x800); /* Config Option Register of LAN */ + writeb(0x0, lp->base+0x802); /* Config and Status Register */ - writeb(ioaddr & 0xff, base+0x80a); /* I/O Base(Low) of LAN */ - writeb((ioaddr >> 8) & 0xff, base+0x80c); /* I/O Base(High) of LAN */ + writeb(ioaddr & 0xff, lp->base+0x80a); /* I/O Base(Low) of LAN */ + writeb((ioaddr >> 8) & 0xff, lp->base+0x80c); /* I/O Base(High) of LAN */ - writeb(0x45, base+0x820); /* Config Option Register of Modem */ - writeb(0x8, base+0x822); /* Config and Status Register */ + writeb(0x45, lp->base+0x820); /* Config Option Register of Modem */ + writeb(0x8, lp->base+0x822); /* Config and Status Register */ - iounmap(base); - j = pcmcia_release_window(link->win); - if (j != 0) - cs_error(link, ReleaseWindow, j); return 0; } @@ -651,8 +662,25 @@ static int fmvj18x_setup_mfc(struct pcmcia_device *link) static void fmvj18x_release(struct pcmcia_device *link) { - DEBUG(0, "fmvj18x_release(0x%p)\n", link); - pcmcia_disable_device(link); + + struct net_device *dev = link->priv; + local_info_t *lp = netdev_priv(dev); + u_char __iomem *tmp; + int j; + + DEBUG(0, "fmvj18x_release(0x%p)\n", link); + + if (lp->base != NULL) { + tmp = lp->base; + lp->base = NULL; /* set NULL before iounmap */ + iounmap(tmp); + j = pcmcia_release_window(link->win); + if (j != 0) + cs_error(link, ReleaseWindow, j); + } + + pcmcia_disable_device(link); + } static int fmvj18x_suspend(struct pcmcia_device *link) @@ -783,6 +811,13 @@ static irqreturn_t fjn_interrupt(int dummy, void *dev_id) outb(D_TX_INTR, ioaddr + TX_INTR); outb(D_RX_INTR, ioaddr + RX_INTR); + + if (lp->base != NULL) { + /* Ack interrupt for multifunction card */ + writeb(0x01, lp->base+0x802); + writeb(0x09, lp->base+0x822); + } + return IRQ_HANDLED; } /* fjn_interrupt */ diff --git a/drivers/net/phy/smsc.c b/drivers/net/phy/smsc.c index 73baa7a3bb0e..c05d38d46350 100644 --- a/drivers/net/phy/smsc.c +++ b/drivers/net/phy/smsc.c @@ -126,6 +126,27 @@ static struct phy_driver lan8700_driver = { .driver = { .owner = THIS_MODULE, } }; +static struct phy_driver lan911x_int_driver = { + .phy_id = 0x0007c0d0, /* OUI=0x00800f, Model#=0x0d */ + .phy_id_mask = 0xfffffff0, + .name = "SMSC LAN911x Internal PHY", + + .features = (PHY_BASIC_FEATURES | SUPPORTED_Pause + | SUPPORTED_Asym_Pause), + .flags = PHY_HAS_INTERRUPT | PHY_HAS_MAGICANEG, + + /* basic functions */ + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .config_init = smsc_phy_config_init, + + /* IRQ related */ + .ack_interrupt = smsc_phy_ack_interrupt, + .config_intr = smsc_phy_config_intr, + + .driver = { .owner = THIS_MODULE, } +}; + static int __init smsc_init(void) { int ret; @@ -142,8 +163,14 @@ static int __init smsc_init(void) if (ret) goto err3; + ret = phy_driver_register (&lan911x_int_driver); + if (ret) + goto err4; + return 0; +err4: + phy_driver_unregister (&lan8700_driver); err3: phy_driver_unregister (&lan8187_driver); err2: @@ -154,6 +181,7 @@ err1: static void __exit smsc_exit(void) { + phy_driver_unregister (&lan911x_int_driver); phy_driver_unregister (&lan8700_driver); phy_driver_unregister (&lan8187_driver); phy_driver_unregister (&lan83c185_driver); diff --git a/drivers/net/sfc/Kconfig b/drivers/net/sfc/Kconfig index 3be13b592b4d..3e25fb38f739 100644 --- a/drivers/net/sfc/Kconfig +++ b/drivers/net/sfc/Kconfig @@ -12,3 +12,11 @@ config SFC To compile this driver as a module, choose M here. The module will be called sfc. +config SFC_MTD + bool "Solarflare Solarstorm SFC4000 flash MTD support" + depends on SFC && MTD + default y + help + This exposes the on-board flash memory as an MTD device (e.g. + /dev/mtd1). This makes it possible to upload new boot code + to the NIC. diff --git a/drivers/net/sfc/Makefile b/drivers/net/sfc/Makefile index c8f5704c8fb1..e507daa4f0e8 100644 --- a/drivers/net/sfc/Makefile +++ b/drivers/net/sfc/Makefile @@ -1,5 +1,6 @@ sfc-y += efx.o falcon.o tx.o rx.o falcon_xmac.o \ selftest.o ethtool.o xfp_phy.o \ mdio_10g.o tenxpress.o boards.o sfe4001.o +sfc-$(CONFIG_SFC_MTD) += mtd.o obj-$(CONFIG_SFC) += sfc.o diff --git a/drivers/net/sfc/boards.c b/drivers/net/sfc/boards.c index 99e602373269..edf026280bec 100644 --- a/drivers/net/sfc/boards.c +++ b/drivers/net/sfc/boards.c @@ -11,6 +11,7 @@ #include "phy.h" #include "boards.h" #include "efx.h" +#include "workarounds.h" /* Macros for unpacking the board revision */ /* The revision info is in host byte order. */ @@ -52,9 +53,128 @@ static void board_blink(struct efx_nic *efx, bool blink) } /***************************************************************************** + * Support for LM87 sensor chip used on several boards + */ +#define LM87_REG_ALARMS1 0x41 +#define LM87_REG_ALARMS2 0x42 +#define LM87_IN_LIMITS(nr, _min, _max) \ + 0x2B + (nr) * 2, _max, 0x2C + (nr) * 2, _min +#define LM87_AIN_LIMITS(nr, _min, _max) \ + 0x3B + (nr), _max, 0x1A + (nr), _min +#define LM87_TEMP_INT_LIMITS(_min, _max) \ + 0x39, _max, 0x3A, _min +#define LM87_TEMP_EXT1_LIMITS(_min, _max) \ + 0x37, _max, 0x38, _min + +#define LM87_ALARM_TEMP_INT 0x10 +#define LM87_ALARM_TEMP_EXT1 0x20 + +#if defined(CONFIG_SENSORS_LM87) || defined(CONFIG_SENSORS_LM87_MODULE) + +static int efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info, + const u8 *reg_values) +{ + struct i2c_client *client = i2c_new_device(&efx->i2c_adap, info); + int rc; + + if (!client) + return -EIO; + + while (*reg_values) { + u8 reg = *reg_values++; + u8 value = *reg_values++; + rc = i2c_smbus_write_byte_data(client, reg, value); + if (rc) + goto err; + } + + efx->board_info.hwmon_client = client; + return 0; + +err: + i2c_unregister_device(client); + return rc; +} + +static void efx_fini_lm87(struct efx_nic *efx) +{ + i2c_unregister_device(efx->board_info.hwmon_client); +} + +static int efx_check_lm87(struct efx_nic *efx, unsigned mask) +{ + struct i2c_client *client = efx->board_info.hwmon_client; + s32 alarms1, alarms2; + + /* If link is up then do not monitor temperature */ + if (EFX_WORKAROUND_7884(efx) && efx->link_up) + return 0; + + alarms1 = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS1); + alarms2 = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS2); + if (alarms1 < 0) + return alarms1; + if (alarms2 < 0) + return alarms2; + alarms1 &= mask; + alarms2 &= mask >> 8; + if (alarms1 || alarms2) { + EFX_ERR(efx, + "LM87 detected a hardware failure (status %02x:%02x)" + "%s%s\n", + alarms1, alarms2, + (alarms1 & LM87_ALARM_TEMP_INT) ? " INTERNAL" : "", + (alarms1 & LM87_ALARM_TEMP_EXT1) ? " EXTERNAL" : ""); + return -ERANGE; + } + + return 0; +} + +#else /* !CONFIG_SENSORS_LM87 */ + +static inline int +efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info, + const u8 *reg_values) +{ + return 0; +} +static inline void efx_fini_lm87(struct efx_nic *efx) +{ +} +static inline int efx_check_lm87(struct efx_nic *efx, unsigned mask) +{ + return 0; +} + +#endif /* CONFIG_SENSORS_LM87 */ + +/***************************************************************************** * Support for the SFE4002 * */ +static u8 sfe4002_lm87_channel = 0x03; /* use AIN not FAN inputs */ + +static const u8 sfe4002_lm87_regs[] = { + LM87_IN_LIMITS(0, 0x83, 0x91), /* 2.5V: 1.8V +/- 5% */ + LM87_IN_LIMITS(1, 0x51, 0x5a), /* Vccp1: 1.2V +/- 5% */ + LM87_IN_LIMITS(2, 0xb6, 0xca), /* 3.3V: 3.3V +/- 5% */ + LM87_IN_LIMITS(3, 0xb0, 0xc9), /* 5V: 4.6-5.2V */ + LM87_IN_LIMITS(4, 0xb0, 0xe0), /* 12V: 11-14V */ + LM87_IN_LIMITS(5, 0x44, 0x4b), /* Vccp2: 1.0V +/- 5% */ + LM87_AIN_LIMITS(0, 0xa0, 0xb2), /* AIN1: 1.66V +/- 5% */ + LM87_AIN_LIMITS(1, 0x91, 0xa1), /* AIN2: 1.5V +/- 5% */ + LM87_TEMP_INT_LIMITS(10, 60), /* board */ + LM87_TEMP_EXT1_LIMITS(10, 70), /* Falcon */ + 0 +}; + +static struct i2c_board_info sfe4002_hwmon_info = { + I2C_BOARD_INFO("lm87", 0x2e), + .platform_data = &sfe4002_lm87_channel, + .irq = -1, +}; + /****************************************************************************/ /* LED allocations. Note that on rev A0 boards the schematic and the reality * differ: red and green are swapped. Below is the fixed (A1) layout (there @@ -84,11 +204,27 @@ static void sfe4002_fault_led(struct efx_nic *efx, bool state) QUAKE_LED_OFF); } +static int sfe4002_check_hw(struct efx_nic *efx) +{ + /* A0 board rev. 4002s report a temperature fault the whole time + * (bad sensor) so we mask it out. */ + unsigned alarm_mask = + (efx->board_info.major == 0 && efx->board_info.minor == 0) ? + ~LM87_ALARM_TEMP_EXT1 : ~0; + + return efx_check_lm87(efx, alarm_mask); +} + static int sfe4002_init(struct efx_nic *efx) { + int rc = efx_init_lm87(efx, &sfe4002_hwmon_info, sfe4002_lm87_regs); + if (rc) + return rc; + efx->board_info.monitor = sfe4002_check_hw; efx->board_info.init_leds = sfe4002_init_leds; efx->board_info.set_fault_led = sfe4002_fault_led; efx->board_info.blink = board_blink; + efx->board_info.fini = efx_fini_lm87; return 0; } diff --git a/drivers/net/sfc/efx.c b/drivers/net/sfc/efx.c index 5b05789f0b79..ac7bdbf3fd4a 100644 --- a/drivers/net/sfc/efx.c +++ b/drivers/net/sfc/efx.c @@ -77,11 +77,6 @@ static int napi_weight = 64; */ unsigned int efx_monitor_interval = 1 * HZ; -/* This controls whether or not the hardware monitor will trigger a - * reset when it detects an error condition. - */ -static unsigned int monitor_reset = true; - /* This controls whether or not the driver will initialise devices * with invalid MAC addresses stored in the EEPROM or flash. If true, * such devices will be initialised with a random locally-generated @@ -1176,17 +1171,6 @@ static void efx_monitor(struct work_struct *data) rc = falcon_check_xmac(efx); mutex_unlock(&efx->mac_lock); - if (rc) { - if (monitor_reset) { - EFX_ERR(efx, "hardware monitor detected a fault: " - "triggering reset\n"); - efx_schedule_reset(efx, RESET_TYPE_MONITOR); - } else { - EFX_ERR(efx, "hardware monitor detected a fault, " - "skipping reset\n"); - } - } - queue_delayed_work(efx->workqueue, &efx->monitor_work, efx_monitor_interval); } @@ -1358,12 +1342,11 @@ static void efx_watchdog(struct net_device *net_dev) { struct efx_nic *efx = netdev_priv(net_dev); - EFX_ERR(efx, "TX stuck with stop_count=%d port_enabled=%d: %s\n", - atomic_read(&efx->netif_stop_count), efx->port_enabled, - monitor_reset ? "resetting channels" : "skipping reset"); + EFX_ERR(efx, "TX stuck with stop_count=%d port_enabled=%d:" + " resetting channels\n", + atomic_read(&efx->netif_stop_count), efx->port_enabled); - if (monitor_reset) - efx_schedule_reset(efx, RESET_TYPE_MONITOR); + efx_schedule_reset(efx, RESET_TYPE_TX_WATCHDOG); } @@ -1459,6 +1442,7 @@ static int efx_netdev_event(struct notifier_block *this, struct efx_nic *efx = netdev_priv(net_dev); strcpy(efx->name, net_dev->name); + efx_mtd_rename(efx); } return NOTIFY_DONE; @@ -1550,6 +1534,7 @@ void efx_reset_down(struct efx_nic *efx, struct ethtool_cmd *ecmd) efx_stop_all(efx); mutex_lock(&efx->mac_lock); + mutex_lock(&efx->spi_lock); rc = falcon_xmac_get_settings(efx, ecmd); if (rc) @@ -1582,6 +1567,7 @@ int efx_reset_up(struct efx_nic *efx, struct ethtool_cmd *ecmd, bool ok) EFX_ERR(efx, "could not restore PHY settings\n"); } + mutex_unlock(&efx->spi_lock); mutex_unlock(&efx->mac_lock); if (ok) { @@ -1777,6 +1763,7 @@ static int efx_init_struct(struct efx_nic *efx, struct efx_nic_type *type, memset(efx, 0, sizeof(*efx)); spin_lock_init(&efx->biu_lock); spin_lock_init(&efx->phy_lock); + mutex_init(&efx->spi_lock); INIT_WORK(&efx->reset_work, efx_reset_work); INIT_DELAYED_WORK(&efx->monitor_work, efx_monitor); efx->pci_dev = pci_dev; @@ -1911,6 +1898,8 @@ static void efx_pci_remove(struct pci_dev *pci_dev) if (!efx) return; + efx_mtd_remove(efx); + /* Mark the NIC as fini, then stop the interface */ rtnl_lock(); efx->state = STATE_FINI; @@ -2077,6 +2066,7 @@ static int __devinit efx_pci_probe(struct pci_dev *pci_dev, EFX_LOG(efx, "initialisation successful\n"); + efx_mtd_probe(efx); /* allowed to fail */ return 0; fail5: diff --git a/drivers/net/sfc/efx.h b/drivers/net/sfc/efx.h index d02937b70eee..dd0d45b9e71f 100644 --- a/drivers/net/sfc/efx.h +++ b/drivers/net/sfc/efx.h @@ -58,6 +58,16 @@ extern int efx_port_dummy_op_int(struct efx_nic *efx); extern void efx_port_dummy_op_void(struct efx_nic *efx); extern void efx_port_dummy_op_blink(struct efx_nic *efx, bool blink); +/* MTD */ +#ifdef CONFIG_SFC_MTD +extern int efx_mtd_probe(struct efx_nic *efx); +extern void efx_mtd_rename(struct efx_nic *efx); +extern void efx_mtd_remove(struct efx_nic *efx); +#else +static inline int efx_mtd_probe(struct efx_nic *efx) { return 0; } +static inline void efx_mtd_rename(struct efx_nic *efx) {} +static inline void efx_mtd_remove(struct efx_nic *efx) {} +#endif extern unsigned int efx_monitor_interval; diff --git a/drivers/net/sfc/enum.h b/drivers/net/sfc/enum.h index cec15dbb88e4..41e758e8fdb1 100644 --- a/drivers/net/sfc/enum.h +++ b/drivers/net/sfc/enum.h @@ -72,7 +72,7 @@ extern const char *efx_loopback_mode_names[]; * @RESET_TYPE_ALL: reset everything but PCI core blocks * @RESET_TYPE_WORLD: reset everything, save & restore PCI config * @RESET_TYPE_DISABLE: disable NIC - * @RESET_TYPE_MONITOR: reset due to hardware monitor + * @RESET_TYPE_TX_WATCHDOG: reset due to TX watchdog * @RESET_TYPE_INT_ERROR: reset due to internal error * @RESET_TYPE_RX_RECOVERY: reset to recover from RX datapath errors * @RESET_TYPE_RX_DESC_FETCH: pcie error during rx descriptor fetch @@ -86,7 +86,7 @@ enum reset_type { RESET_TYPE_WORLD = 2, RESET_TYPE_DISABLE = 3, RESET_TYPE_MAX_METHOD, - RESET_TYPE_MONITOR, + RESET_TYPE_TX_WATCHDOG, RESET_TYPE_INT_ERROR, RESET_TYPE_RX_RECOVERY, RESET_TYPE_RX_DESC_FETCH, diff --git a/drivers/net/sfc/ethtool.c b/drivers/net/sfc/ethtool.c index fa98af58223e..abd8fcd6e62d 100644 --- a/drivers/net/sfc/ethtool.c +++ b/drivers/net/sfc/ethtool.c @@ -172,10 +172,7 @@ static struct efx_ethtool_stat efx_ethtool_stats[] = { /* Number of ethtool statistics */ #define EFX_ETHTOOL_NUM_STATS ARRAY_SIZE(efx_ethtool_stats) -/* EEPROM range with gPXE configuration */ #define EFX_ETHTOOL_EEPROM_MAGIC 0xEFAB -#define EFX_ETHTOOL_EEPROM_MIN 0x100U -#define EFX_ETHTOOL_EEPROM_MAX 0x400U /************************************************************************** * @@ -545,8 +542,8 @@ static int efx_ethtool_get_eeprom_len(struct net_device *net_dev) if (!spi) return 0; - return min(spi->size, EFX_ETHTOOL_EEPROM_MAX) - - min(spi->size, EFX_ETHTOOL_EEPROM_MIN); + return min(spi->size, EFX_EEPROM_BOOTCONFIG_END) - + min(spi->size, EFX_EEPROM_BOOTCONFIG_START); } static int efx_ethtool_get_eeprom(struct net_device *net_dev, @@ -557,8 +554,10 @@ static int efx_ethtool_get_eeprom(struct net_device *net_dev, size_t len; int rc; - rc = falcon_spi_read(spi, eeprom->offset + EFX_ETHTOOL_EEPROM_MIN, + mutex_lock(&efx->spi_lock); + rc = falcon_spi_read(spi, eeprom->offset + EFX_EEPROM_BOOTCONFIG_START, eeprom->len, &len, buf); + mutex_unlock(&efx->spi_lock); eeprom->magic = EFX_ETHTOOL_EEPROM_MAGIC; eeprom->len = len; return rc; @@ -575,8 +574,10 @@ static int efx_ethtool_set_eeprom(struct net_device *net_dev, if (eeprom->magic != EFX_ETHTOOL_EEPROM_MAGIC) return -EINVAL; - rc = falcon_spi_write(spi, eeprom->offset + EFX_ETHTOOL_EEPROM_MIN, + mutex_lock(&efx->spi_lock); + rc = falcon_spi_write(spi, eeprom->offset + EFX_EEPROM_BOOTCONFIG_START, eeprom->len, &len, buf); + mutex_unlock(&efx->spi_lock); eeprom->len = len; return rc; } diff --git a/drivers/net/sfc/falcon.c b/drivers/net/sfc/falcon.c index 31ed1f49de00..71e0bed60616 100644 --- a/drivers/net/sfc/falcon.c +++ b/drivers/net/sfc/falcon.c @@ -1628,9 +1628,9 @@ static int falcon_spi_wait(struct efx_nic *efx) } } -static int falcon_spi_cmd(const struct efx_spi_device *spi, - unsigned int command, int address, - const void *in, void *out, unsigned int len) +int falcon_spi_cmd(const struct efx_spi_device *spi, + unsigned int command, int address, + const void *in, void *out, unsigned int len) { struct efx_nic *efx = spi->efx; bool addressed = (address >= 0); @@ -1641,6 +1641,7 @@ static int falcon_spi_cmd(const struct efx_spi_device *spi, /* Input validation */ if (len > FALCON_SPI_MAX_LEN) return -EINVAL; + BUG_ON(!mutex_is_locked(&efx->spi_lock)); /* Check SPI not currently being accessed */ rc = falcon_spi_wait(efx); @@ -1699,8 +1700,7 @@ efx_spi_munge_command(const struct efx_spi_device *spi, return command | (((address >> 8) & spi->munge_address) << 3); } - -static int falcon_spi_fast_wait(const struct efx_spi_device *spi) +int falcon_spi_fast_wait(const struct efx_spi_device *spi) { u8 status; int i, rc; @@ -2253,13 +2253,15 @@ int falcon_read_nvram(struct efx_nic *efx, struct falcon_nvconfig *nvconfig_out) __le16 *word, *limit; u32 csum; - region = kmalloc(NVCONFIG_END, GFP_KERNEL); + region = kmalloc(FALCON_NVCONFIG_END, GFP_KERNEL); if (!region) return -ENOMEM; nvconfig = region + NVCONFIG_OFFSET; spi = efx->spi_flash ? efx->spi_flash : efx->spi_eeprom; - rc = falcon_spi_read(spi, 0, NVCONFIG_END, NULL, region); + mutex_lock(&efx->spi_lock); + rc = falcon_spi_read(spi, 0, FALCON_NVCONFIG_END, NULL, region); + mutex_unlock(&efx->spi_lock); if (rc) { EFX_ERR(efx, "Failed to read %s\n", efx->spi_flash ? "flash" : "EEPROM"); @@ -2283,7 +2285,7 @@ int falcon_read_nvram(struct efx_nic *efx, struct falcon_nvconfig *nvconfig_out) limit = (__le16 *) (nvconfig + 1); } else { word = region; - limit = region + NVCONFIG_END; + limit = region + FALCON_NVCONFIG_END; } for (csum = 0; word < limit; ++word) csum += le16_to_cpu(*word); @@ -2555,6 +2557,11 @@ static int falcon_spi_device_init(struct efx_nic *efx, SPI_DEV_TYPE_FIELD(device_type, SPI_DEV_TYPE_ADDR_LEN); spi_device->munge_address = (spi_device->size == 1 << 9 && spi_device->addr_len == 1); + spi_device->erase_command = + SPI_DEV_TYPE_FIELD(device_type, SPI_DEV_TYPE_ERASE_CMD); + spi_device->erase_size = + 1 << SPI_DEV_TYPE_FIELD(device_type, + SPI_DEV_TYPE_ERASE_SIZE); spi_device->block_size = 1 << SPI_DEV_TYPE_FIELD(device_type, SPI_DEV_TYPE_BLOCK_SIZE); diff --git a/drivers/net/sfc/falcon_hwdefs.h b/drivers/net/sfc/falcon_hwdefs.h index 5d584b0dbb51..040e70ed4ec7 100644 --- a/drivers/net/sfc/falcon_hwdefs.h +++ b/drivers/net/sfc/falcon_hwdefs.h @@ -1150,7 +1150,6 @@ struct falcon_nvconfig_board_v3 { (((type) >> EFX_LOW_BIT(field)) & EFX_MASK32(EFX_WIDTH(field))) #define NVCONFIG_OFFSET 0x300 -#define NVCONFIG_END 0x400 #define NVCONFIG_BOARD_MAGIC_NUM 0xFA1C struct falcon_nvconfig { diff --git a/drivers/net/sfc/mdio_10g.c b/drivers/net/sfc/mdio_10g.c index 003e48dcb2f3..19e25210b687 100644 --- a/drivers/net/sfc/mdio_10g.c +++ b/drivers/net/sfc/mdio_10g.c @@ -260,6 +260,41 @@ void mdio_clause45_phy_reconfigure(struct efx_nic *efx) MDIO_MMDREG_CTRL1, ctrl2); } +static void mdio_clause45_set_mmd_lpower(struct efx_nic *efx, + int lpower, int mmd) +{ + int phy = efx->mii.phy_id; + int stat = mdio_clause45_read(efx, phy, mmd, MDIO_MMDREG_STAT1); + int ctrl1, ctrl2; + + EFX_TRACE(efx, "Setting low power mode for MMD %d to %d\n", + mmd, lpower); + + if (stat & (1 << MDIO_MMDREG_STAT1_LPABLE_LBN)) { + ctrl1 = ctrl2 = mdio_clause45_read(efx, phy, + mmd, MDIO_MMDREG_CTRL1); + if (lpower) + ctrl2 |= (1 << MDIO_MMDREG_CTRL1_LPOWER_LBN); + else + ctrl2 &= ~(1 << MDIO_MMDREG_CTRL1_LPOWER_LBN); + if (ctrl1 != ctrl2) + mdio_clause45_write(efx, phy, mmd, + MDIO_MMDREG_CTRL1, ctrl2); + } +} + +void mdio_clause45_set_mmds_lpower(struct efx_nic *efx, + int low_power, unsigned int mmd_mask) +{ + int mmd = 0; + while (mmd_mask) { + if (mmd_mask & 1) + mdio_clause45_set_mmd_lpower(efx, low_power, mmd); + mmd_mask = (mmd_mask >> 1); + mmd++; + } +} + /** * mdio_clause45_get_settings - Read (some of) the PHY settings over MDIO. * @efx: Efx NIC diff --git a/drivers/net/sfc/mdio_10g.h b/drivers/net/sfc/mdio_10g.h index 19c42eaf7fb4..db9f358349c6 100644 --- a/drivers/net/sfc/mdio_10g.h +++ b/drivers/net/sfc/mdio_10g.h @@ -54,6 +54,9 @@ /* Loopback bit for WIS, PCS, PHYSX and DTEXS */ #define MDIO_MMDREG_CTRL1_LBACK_LBN (14) #define MDIO_MMDREG_CTRL1_LBACK_WIDTH (1) +/* Low power */ +#define MDIO_MMDREG_CTRL1_LPOWER_LBN (11) +#define MDIO_MMDREG_CTRL1_LPOWER_WIDTH (1) /* Bits in MMDREG_STAT1 */ #define MDIO_MMDREG_STAT1_FAULT_LBN (7) @@ -240,6 +243,10 @@ extern void mdio_clause45_transmit_disable(struct efx_nic *efx); /* Generic part of reconfigure: set/clear loopback bits */ extern void mdio_clause45_phy_reconfigure(struct efx_nic *efx); +/* Set the power state of the specified MMDs */ +extern void mdio_clause45_set_mmds_lpower(struct efx_nic *efx, + int low_power, unsigned int mmd_mask); + /* Read (some of) the PHY settings over MDIO */ extern void mdio_clause45_get_settings(struct efx_nic *efx, struct ethtool_cmd *ecmd); diff --git a/drivers/net/sfc/mtd.c b/drivers/net/sfc/mtd.c new file mode 100644 index 000000000000..a1e6c2875fc0 --- /dev/null +++ b/drivers/net/sfc/mtd.c @@ -0,0 +1,268 @@ +/**************************************************************************** + * Driver for Solarflare Solarstorm network controllers and boards + * Copyright 2005-2006 Fen Systems Ltd. + * Copyright 2006-2008 Solarflare Communications Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation, incorporated herein by reference. + */ + +#include <linux/module.h> +#include <linux/mtd/mtd.h> +#include <linux/delay.h> + +#define EFX_DRIVER_NAME "sfc_mtd" +#include "net_driver.h" +#include "spi.h" + +#define EFX_SPI_VERIFY_BUF_LEN 16 + +struct efx_mtd { + const struct efx_spi_device *spi; + struct mtd_info mtd; + char name[IFNAMSIZ + 20]; +}; + +/* SPI utilities */ + +static int efx_spi_slow_wait(struct efx_mtd *efx_mtd, bool uninterruptible) +{ + const struct efx_spi_device *spi = efx_mtd->spi; + struct efx_nic *efx = spi->efx; + u8 status; + int rc, i; + + /* Wait up to 4s for flash/EEPROM to finish a slow operation. */ + for (i = 0; i < 40; i++) { + __set_current_state(uninterruptible ? + TASK_UNINTERRUPTIBLE : TASK_INTERRUPTIBLE); + schedule_timeout(HZ / 10); + rc = falcon_spi_cmd(spi, SPI_RDSR, -1, NULL, + &status, sizeof(status)); + if (rc) + return rc; + if (!(status & SPI_STATUS_NRDY)) + return 0; + if (signal_pending(current)) + return -EINTR; + } + EFX_ERR(efx, "timed out waiting for %s\n", efx_mtd->name); + return -ETIMEDOUT; +} + +static int efx_spi_unlock(const struct efx_spi_device *spi) +{ + const u8 unlock_mask = (SPI_STATUS_BP2 | SPI_STATUS_BP1 | + SPI_STATUS_BP0); + u8 status; + int rc; + + rc = falcon_spi_cmd(spi, SPI_RDSR, -1, NULL, &status, sizeof(status)); + if (rc) + return rc; + + if (!(status & unlock_mask)) + return 0; /* already unlocked */ + + rc = falcon_spi_cmd(spi, SPI_WREN, -1, NULL, NULL, 0); + if (rc) + return rc; + rc = falcon_spi_cmd(spi, SPI_SST_EWSR, -1, NULL, NULL, 0); + if (rc) + return rc; + + status &= ~unlock_mask; + rc = falcon_spi_cmd(spi, SPI_WRSR, -1, &status, NULL, sizeof(status)); + if (rc) + return rc; + rc = falcon_spi_fast_wait(spi); + if (rc) + return rc; + + return 0; +} + +static int efx_spi_erase(struct efx_mtd *efx_mtd, loff_t start, size_t len) +{ + const struct efx_spi_device *spi = efx_mtd->spi; + unsigned pos, block_len; + u8 empty[EFX_SPI_VERIFY_BUF_LEN]; + u8 buffer[EFX_SPI_VERIFY_BUF_LEN]; + int rc; + + if (len != spi->erase_size) + return -EINVAL; + + if (spi->erase_command == 0) + return -EOPNOTSUPP; + + rc = efx_spi_unlock(spi); + if (rc) + return rc; + rc = falcon_spi_cmd(spi, SPI_WREN, -1, NULL, NULL, 0); + if (rc) + return rc; + rc = falcon_spi_cmd(spi, spi->erase_command, start, NULL, NULL, 0); + if (rc) + return rc; + rc = efx_spi_slow_wait(efx_mtd, false); + + /* Verify the entire region has been wiped */ + memset(empty, 0xff, sizeof(empty)); + for (pos = 0; pos < len; pos += block_len) { + block_len = min(len - pos, sizeof(buffer)); + rc = falcon_spi_read(spi, start + pos, block_len, NULL, buffer); + if (rc) + return rc; + if (memcmp(empty, buffer, block_len)) + return -EIO; + + /* Avoid locking up the system */ + cond_resched(); + if (signal_pending(current)) + return -EINTR; + } + + return rc; +} + +/* MTD interface */ + +static int efx_mtd_read(struct mtd_info *mtd, loff_t start, size_t len, + size_t *retlen, u8 *buffer) +{ + struct efx_mtd *efx_mtd = mtd->priv; + const struct efx_spi_device *spi = efx_mtd->spi; + struct efx_nic *efx = spi->efx; + int rc; + + rc = mutex_lock_interruptible(&efx->spi_lock); + if (rc) + return rc; + rc = falcon_spi_read(spi, FALCON_FLASH_BOOTCODE_START + start, + len, retlen, buffer); + mutex_unlock(&efx->spi_lock); + return rc; +} + +static int efx_mtd_erase(struct mtd_info *mtd, struct erase_info *erase) +{ + struct efx_mtd *efx_mtd = mtd->priv; + struct efx_nic *efx = efx_mtd->spi->efx; + int rc; + + rc = mutex_lock_interruptible(&efx->spi_lock); + if (rc) + return rc; + rc = efx_spi_erase(efx_mtd, FALCON_FLASH_BOOTCODE_START + erase->addr, + erase->len); + mutex_unlock(&efx->spi_lock); + + if (rc == 0) { + erase->state = MTD_ERASE_DONE; + } else { + erase->state = MTD_ERASE_FAILED; + erase->fail_addr = 0xffffffff; + } + mtd_erase_callback(erase); + return rc; +} + +static int efx_mtd_write(struct mtd_info *mtd, loff_t start, + size_t len, size_t *retlen, const u8 *buffer) +{ + struct efx_mtd *efx_mtd = mtd->priv; + const struct efx_spi_device *spi = efx_mtd->spi; + struct efx_nic *efx = spi->efx; + int rc; + + rc = mutex_lock_interruptible(&efx->spi_lock); + if (rc) + return rc; + rc = falcon_spi_write(spi, FALCON_FLASH_BOOTCODE_START + start, + len, retlen, buffer); + mutex_unlock(&efx->spi_lock); + return rc; +} + +static void efx_mtd_sync(struct mtd_info *mtd) +{ + struct efx_mtd *efx_mtd = mtd->priv; + struct efx_nic *efx = efx_mtd->spi->efx; + int rc; + + mutex_lock(&efx->spi_lock); + rc = efx_spi_slow_wait(efx_mtd, true); + mutex_unlock(&efx->spi_lock); + + if (rc) + EFX_ERR(efx, "%s sync failed (%d)\n", efx_mtd->name, rc); + return; +} + +void efx_mtd_remove(struct efx_nic *efx) +{ + if (efx->spi_flash && efx->spi_flash->mtd) { + struct efx_mtd *efx_mtd = efx->spi_flash->mtd; + int rc; + + for (;;) { + rc = del_mtd_device(&efx_mtd->mtd); + if (rc != -EBUSY) + break; + ssleep(1); + } + WARN_ON(rc); + kfree(efx_mtd); + } +} + +void efx_mtd_rename(struct efx_nic *efx) +{ + if (efx->spi_flash && efx->spi_flash->mtd) { + struct efx_mtd *efx_mtd = efx->spi_flash->mtd; + snprintf(efx_mtd->name, sizeof(efx_mtd->name), + "%s sfc_flash_bootrom", efx->name); + } +} + +int efx_mtd_probe(struct efx_nic *efx) +{ + struct efx_spi_device *spi = efx->spi_flash; + struct efx_mtd *efx_mtd; + + if (!spi || spi->size <= FALCON_FLASH_BOOTCODE_START) + return -ENODEV; + + efx_mtd = kzalloc(sizeof(*efx_mtd), GFP_KERNEL); + if (!efx_mtd) + return -ENOMEM; + + efx_mtd->spi = spi; + spi->mtd = efx_mtd; + + efx_mtd->mtd.type = MTD_NORFLASH; + efx_mtd->mtd.flags = MTD_CAP_NORFLASH; + efx_mtd->mtd.size = spi->size - FALCON_FLASH_BOOTCODE_START; + efx_mtd->mtd.erasesize = spi->erase_size; + efx_mtd->mtd.writesize = 1; + efx_mtd_rename(efx); + + efx_mtd->mtd.owner = THIS_MODULE; + efx_mtd->mtd.priv = efx_mtd; + efx_mtd->mtd.name = efx_mtd->name; + efx_mtd->mtd.erase = efx_mtd_erase; + efx_mtd->mtd.read = efx_mtd_read; + efx_mtd->mtd.write = efx_mtd_write; + efx_mtd->mtd.sync = efx_mtd_sync; + + if (add_mtd_device(&efx_mtd->mtd)) { + kfree(efx_mtd); + spi->mtd = NULL; + /* add_mtd_device() returns 1 if the MTD table is full */ + return -ENOMEM; + } + + return 0; +} diff --git a/drivers/net/sfc/net_driver.h b/drivers/net/sfc/net_driver.h index cdb11fad6050..e596c9a6a4c4 100644 --- a/drivers/net/sfc/net_driver.h +++ b/drivers/net/sfc/net_driver.h @@ -414,6 +414,7 @@ struct efx_blinker { * @init_leds: Sets up board LEDs * @set_fault_led: Turns the fault LED on or off * @blink: Starts/stops blinking + * @monitor: Board-specific health check function * @fini: Cleanup function * @blinker: used to blink LEDs in software * @hwmon_client: I2C client for hardware monitor @@ -428,6 +429,7 @@ struct efx_board { * have a separate init callback that happens later than * board init. */ int (*init_leds)(struct efx_nic *efx); + int (*monitor) (struct efx_nic *nic); void (*set_fault_led) (struct efx_nic *efx, bool state); void (*blink) (struct efx_nic *efx, bool start); void (*fini) (struct efx_nic *nic); @@ -525,11 +527,15 @@ struct efx_phy_operations { * @enum efx_phy_mode - PHY operating mode flags * @PHY_MODE_NORMAL: on and should pass traffic * @PHY_MODE_TX_DISABLED: on with TX disabled + * @PHY_MODE_LOW_POWER: set to low power through MDIO + * @PHY_MODE_OFF: switched off through external control * @PHY_MODE_SPECIAL: on but will not pass traffic */ enum efx_phy_mode { PHY_MODE_NORMAL = 0, PHY_MODE_TX_DISABLED = 1, + PHY_MODE_LOW_POWER = 2, + PHY_MODE_OFF = 4, PHY_MODE_SPECIAL = 8, }; @@ -655,6 +661,7 @@ union efx_multicast_hash { * This field will be %NULL if no flash device is present. * @spi_eeprom: SPI EEPROM device * This field will be %NULL if no EEPROM device is present. + * @spi_lock: SPI bus lock * @n_rx_nodesc_drop_cnt: RX no descriptor drop count * @nic_data: Hardware dependant state * @mac_lock: MAC access lock. Protects @port_enabled, @phy_mode, @@ -731,6 +738,7 @@ struct efx_nic { struct efx_spi_device *spi_flash; struct efx_spi_device *spi_eeprom; + struct mutex spi_lock; unsigned n_rx_nodesc_drop_cnt; diff --git a/drivers/net/sfc/sfe4001.c b/drivers/net/sfc/sfe4001.c index fe4e3fd22330..aa576c559ec8 100644 --- a/drivers/net/sfc/sfe4001.c +++ b/drivers/net/sfc/sfe4001.c @@ -21,6 +21,7 @@ #include "falcon_hwdefs.h" #include "falcon_io.h" #include "mac.h" +#include "workarounds.h" /************************************************************************** * @@ -65,48 +66,9 @@ #define P1_SPARE_LBN 4 #define P1_SPARE_WIDTH 4 - -/************************************************************************** - * - * Temperature Sensor - * - **************************************************************************/ -#define MAX6647 0x4e - -#define RLTS 0x00 -#define RLTE 0x01 -#define RSL 0x02 -#define RCL 0x03 -#define RCRA 0x04 -#define RLHN 0x05 -#define RLLI 0x06 -#define RRHI 0x07 -#define RRLS 0x08 -#define WCRW 0x0a -#define WLHO 0x0b -#define WRHA 0x0c -#define WRLN 0x0e -#define OSHT 0x0f -#define REET 0x10 -#define RIET 0x11 -#define RWOE 0x19 -#define RWOI 0x20 -#define HYS 0x21 -#define QUEUE 0x22 -#define MFID 0xfe -#define REVID 0xff - -/* Status bits */ -#define MAX6647_BUSY (1 << 7) /* ADC is converting */ -#define MAX6647_LHIGH (1 << 6) /* Local high temp. alarm */ -#define MAX6647_LLOW (1 << 5) /* Local low temp. alarm */ -#define MAX6647_RHIGH (1 << 4) /* Remote high temp. alarm */ -#define MAX6647_RLOW (1 << 3) /* Remote low temp. alarm */ -#define MAX6647_FAULT (1 << 2) /* DXN/DXP short/open circuit */ -#define MAX6647_EOT (1 << 1) /* Remote junction overtemp. */ -#define MAX6647_IOT (1 << 0) /* Local junction overtemp. */ - -static const u8 xgphy_max_temperature = 90; +/* Temperature Sensor */ +#define MAX664X_REG_RSL 0x02 +#define MAX664X_REG_WLHO 0x0B static void sfe4001_poweroff(struct efx_nic *efx) { @@ -119,7 +81,7 @@ static void sfe4001_poweroff(struct efx_nic *efx) i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0xff); /* Clear any over-temperature alert */ - i2c_smbus_read_byte_data(hwmon_client, RSL); + i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL); } static int sfe4001_poweron(struct efx_nic *efx) @@ -131,7 +93,7 @@ static int sfe4001_poweron(struct efx_nic *efx) u8 out; /* Clear any previous over-temperature alert */ - rc = i2c_smbus_read_byte_data(hwmon_client, RSL); + rc = i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL); if (rc < 0) return rc; @@ -209,6 +171,34 @@ fail_on: return rc; } +static int sfe4001_check_hw(struct efx_nic *efx) +{ + s32 status; + + /* If XAUI link is up then do not monitor */ + if (EFX_WORKAROUND_7884(efx) && falcon_xaui_link_ok(efx)) + return 0; + + /* Check the powered status of the PHY. Lack of power implies that + * the MAX6647 has shut down power to it, probably due to a temp. + * alarm. Reading the power status rather than the MAX6647 status + * directly because the later is read-to-clear and would thus + * start to power up the PHY again when polled, causing us to blip + * the power undesirably. + * We know we can read from the IO expander because we did + * it during power-on. Assume failure now is bad news. */ + status = i2c_smbus_read_byte_data(efx->board_info.ioexp_client, P1_IN); + if (status >= 0 && + (status & ((1 << P1_AFE_PWD_LBN) | (1 << P1_DSP_PWD25_LBN))) != 0) + return 0; + + /* Use board power control, not PHY power control */ + sfe4001_poweroff(efx); + efx->phy_mode = PHY_MODE_OFF; + + return (status < 0) ? -EIO : -ERANGE; +} + /* On SFE4001 rev A2 and later, we can control the FLASH_CFG_1 pin * using the 3V3X output of the IO-expander. Allow the user to set * this when the device is stopped, and keep it stopped then. @@ -261,35 +251,34 @@ static void sfe4001_fini(struct efx_nic *efx) i2c_unregister_device(efx->board_info.hwmon_client); } +static struct i2c_board_info sfe4001_hwmon_info = { + I2C_BOARD_INFO("max6647", 0x4e), + .irq = -1, +}; + /* This board uses an I2C expander to provider power to the PHY, which needs to * be turned on before the PHY can be used. * Context: Process context, rtnl lock held */ int sfe4001_init(struct efx_nic *efx) { - struct i2c_client *hwmon_client; int rc; - hwmon_client = i2c_new_dummy(&efx->i2c_adap, MAX6647); - if (!hwmon_client) +#if defined(CONFIG_SENSORS_LM90) || defined(CONFIG_SENSORS_LM90_MODULE) + efx->board_info.hwmon_client = + i2c_new_device(&efx->i2c_adap, &sfe4001_hwmon_info); +#else + efx->board_info.hwmon_client = + i2c_new_dummy(&efx->i2c_adap, sfe4001_hwmon_info.addr); +#endif + if (!efx->board_info.hwmon_client) return -EIO; - efx->board_info.hwmon_client = hwmon_client; - /* Set DSP over-temperature alert threshold */ - EFX_INFO(efx, "DSP cut-out at %dC\n", xgphy_max_temperature); - rc = i2c_smbus_write_byte_data(hwmon_client, WLHO, - xgphy_max_temperature); + /* Raise board/PHY high limit from 85 to 90 degrees Celsius */ + rc = i2c_smbus_write_byte_data(efx->board_info.hwmon_client, + MAX664X_REG_WLHO, 90); if (rc) - goto fail_ioexp; - - /* Read it back and verify */ - rc = i2c_smbus_read_byte_data(hwmon_client, RLHN); - if (rc < 0) - goto fail_ioexp; - if (rc != xgphy_max_temperature) { - rc = -EFAULT; - goto fail_ioexp; - } + goto fail_hwmon; efx->board_info.ioexp_client = i2c_new_dummy(&efx->i2c_adap, PCA9539); if (!efx->board_info.ioexp_client) { @@ -301,6 +290,7 @@ int sfe4001_init(struct efx_nic *efx) * blink code. */ efx->board_info.blink = tenxpress_phy_blink; + efx->board_info.monitor = sfe4001_check_hw; efx->board_info.fini = sfe4001_fini; rc = sfe4001_poweron(efx); @@ -319,6 +309,6 @@ fail_on: fail_ioexp: i2c_unregister_device(efx->board_info.ioexp_client); fail_hwmon: - i2c_unregister_device(hwmon_client); + i2c_unregister_device(efx->board_info.hwmon_client); return rc; } diff --git a/drivers/net/sfc/spi.h b/drivers/net/sfc/spi.h index feef61942377..c4aca132348a 100644 --- a/drivers/net/sfc/spi.h +++ b/drivers/net/sfc/spi.h @@ -25,6 +25,7 @@ #define SPI_WRDI 0x04 /* Reset write enable latch */ #define SPI_RDSR 0x05 /* Read status register */ #define SPI_WREN 0x06 /* Set write enable latch */ +#define SPI_SST_EWSR 0x50 /* SST: Enable write to status register */ #define SPI_STATUS_WPEN 0x80 /* Write-protect pin enabled */ #define SPI_STATUS_BP2 0x10 /* Block protection bit 2 */ @@ -36,6 +37,7 @@ /** * struct efx_spi_device - an Efx SPI (Serial Peripheral Interface) device * @efx: The Efx controller that owns this device + * @mtd: MTD state * @device_id: Controller's id for the device * @size: Size (in bytes) * @addr_len: Number of address bytes in read/write commands @@ -44,23 +46,51 @@ * use bit 3 of the command byte as address bit A8, rather * than having a two-byte address. If this flag is set, then * commands should be munged in this way. + * @erase_command: Erase command (or 0 if sector erase not needed). + * @erase_size: Erase sector size (in bytes) + * Erase commands affect sectors with this size and alignment. + * This must be a power of two. * @block_size: Write block size (in bytes). * Write commands are limited to blocks with this size and alignment. - * @read: Read function for the device - * @write: Write function for the device */ struct efx_spi_device { struct efx_nic *efx; +#ifdef CONFIG_SFC_MTD + void *mtd; +#endif int device_id; unsigned int size; unsigned int addr_len; unsigned int munge_address:1; + u8 erase_command; + unsigned int erase_size; unsigned int block_size; }; +int falcon_spi_cmd(const struct efx_spi_device *spi, unsigned int command, + int address, const void* in, void *out, unsigned int len); +int falcon_spi_fast_wait(const struct efx_spi_device *spi); int falcon_spi_read(const struct efx_spi_device *spi, loff_t start, size_t len, size_t *retlen, u8 *buffer); int falcon_spi_write(const struct efx_spi_device *spi, loff_t start, size_t len, size_t *retlen, const u8 *buffer); +/* + * SFC4000 flash is partitioned into: + * 0-0x400 chip and board config (see falcon_hwdefs.h) + * 0x400-0x8000 unused (or may contain VPD if EEPROM not present) + * 0x8000-end boot code (mapped to PCI expansion ROM) + * SFC4000 small EEPROM (size < 0x400) is used for VPD only. + * SFC4000 large EEPROM (size >= 0x400) is partitioned into: + * 0-0x400 chip and board config + * configurable VPD + * 0x800-0x1800 boot config + * Aside from the chip and board config, all of these are optional and may + * be absent or truncated depending on the devices used. + */ +#define FALCON_NVCONFIG_END 0x400U +#define FALCON_FLASH_BOOTCODE_START 0x8000U +#define EFX_EEPROM_BOOTCONFIG_START 0x800U +#define EFX_EEPROM_BOOTCONFIG_END 0x1800U + #endif /* EFX_SPI_H */ diff --git a/drivers/net/sfc/tenxpress.c b/drivers/net/sfc/tenxpress.c index d507c93d666e..8d41c29b9d7b 100644 --- a/drivers/net/sfc/tenxpress.c +++ b/drivers/net/sfc/tenxpress.c @@ -376,6 +376,7 @@ static int tenxpress_phy_check_hw(struct efx_nic *efx) { struct tenxpress_phy_data *phy_data = efx->phy_data; bool link_ok; + int rc = 0; link_ok = tenxpress_link_ok(efx, true); @@ -391,7 +392,22 @@ static int tenxpress_phy_check_hw(struct efx_nic *efx) atomic_set(&phy_data->bad_crc_count, 0); } - return 0; + rc = efx->board_info.monitor(efx); + if (rc) { + EFX_ERR(efx, "Board sensor %s; shutting down PHY\n", + (rc == -ERANGE) ? "reported fault" : "failed"); + if (efx->phy_mode & PHY_MODE_OFF) { + /* Assume that board has shut PHY off */ + phy_data->phy_mode = PHY_MODE_OFF; + } else { + efx->phy_mode |= PHY_MODE_LOW_POWER; + mdio_clause45_set_mmds_lpower(efx, true, + efx->phy_op->mmds); + phy_data->phy_mode |= PHY_MODE_LOW_POWER; + } + } + + return rc; } static void tenxpress_phy_fini(struct efx_nic *efx) diff --git a/drivers/net/sfc/workarounds.h b/drivers/net/sfc/workarounds.h index fa7b49d69288..ec50b90f4285 100644 --- a/drivers/net/sfc/workarounds.h +++ b/drivers/net/sfc/workarounds.h @@ -22,6 +22,8 @@ #define EFX_WORKAROUND_5147 EFX_WORKAROUND_ALWAYS /* RX PCIe double split performance issue */ #define EFX_WORKAROUND_7575 EFX_WORKAROUND_ALWAYS +/* Bit-bashed I2C reads cause performance drop */ +#define EFX_WORKAROUND_7884 EFX_WORKAROUND_ALWAYS /* TX pkt parser problem with <= 16 byte TXes */ #define EFX_WORKAROUND_9141 EFX_WORKAROUND_ALWAYS /* Low rate CRC errors require XAUI reset */ diff --git a/drivers/net/sfc/xfp_phy.c b/drivers/net/sfc/xfp_phy.c index 276151df3a70..91f024662101 100644 --- a/drivers/net/sfc/xfp_phy.c +++ b/drivers/net/sfc/xfp_phy.c @@ -128,6 +128,15 @@ static int xfp_phy_check_hw(struct efx_nic *efx) if (link_up != efx->link_up) falcon_xmac_sim_phy_event(efx); + rc = efx->board_info.monitor(efx); + if (rc) { + struct xfp_phy_data *phy_data = efx->phy_data; + EFX_ERR(efx, "XFP sensor alert; putting PHY into low power\n"); + efx->phy_mode |= PHY_MODE_LOW_POWER; + mdio_clause45_set_mmds_lpower(efx, 1, XFP_REQUIRED_DEVS); + phy_data->phy_mode |= PHY_MODE_LOW_POWER; + } + return rc; } diff --git a/drivers/net/smsc911x.c b/drivers/net/smsc911x.c new file mode 100644 index 000000000000..fe517880fc97 --- /dev/null +++ b/drivers/net/smsc911x.c @@ -0,0 +1,2091 @@ +/*************************************************************************** + * + * Copyright (C) 2004-2008 SMSC + * Copyright (C) 2005-2008 ARM + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * + *************************************************************************** + * Rewritten, heavily based on smsc911x simple driver by SMSC. + * Partly uses io macros from smc91x.c by Nicolas Pitre + * + * Supported devices: + * LAN9115, LAN9116, LAN9117, LAN9118 + * LAN9215, LAN9216, LAN9217, LAN9218 + * LAN9210, LAN9211 + * LAN9220, LAN9221 + * + */ + +#include <linux/crc32.h> +#include <linux/delay.h> +#include <linux/errno.h> +#include <linux/etherdevice.h> +#include <linux/ethtool.h> +#include <linux/init.h> +#include <linux/ioport.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/platform_device.h> +#include <linux/sched.h> +#include <linux/slab.h> +#include <linux/timer.h> +#include <linux/version.h> +#include <linux/bug.h> +#include <linux/bitops.h> +#include <linux/irq.h> +#include <linux/io.h> +#include <linux/phy.h> +#include <linux/smsc911x.h> +#include "smsc911x.h" + +#define SMSC_CHIPNAME "smsc911x" +#define SMSC_MDIONAME "smsc911x-mdio" +#define SMSC_DRV_VERSION "2008-10-21" + +MODULE_LICENSE("GPL"); +MODULE_VERSION(SMSC_DRV_VERSION); + +#if USE_DEBUG > 0 +static int debug = 16; +#else +static int debug = 3; +#endif + +module_param(debug, int, 0); +MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); + +struct smsc911x_data { + void __iomem *ioaddr; + + unsigned int idrev; + + /* used to decide which workarounds apply */ + unsigned int generation; + + /* device configuration (copied from platform_data during probe) */ + unsigned int irq_polarity; + unsigned int irq_type; + phy_interface_t phy_interface; + + /* This needs to be acquired before calling any of below: + * smsc911x_mac_read(), smsc911x_mac_write() + */ + spinlock_t mac_lock; + +#if (!SMSC_CAN_USE_32BIT) + /* spinlock to ensure 16-bit accesses are serialised */ + spinlock_t dev_lock; +#endif + + struct phy_device *phy_dev; + struct mii_bus *mii_bus; + int phy_irq[PHY_MAX_ADDR]; + unsigned int using_extphy; + int last_duplex; + int last_carrier; + + u32 msg_enable; + unsigned int gpio_setting; + unsigned int gpio_orig_setting; + struct net_device *dev; + struct napi_struct napi; + + unsigned int software_irq_signal; + +#ifdef USE_PHY_WORK_AROUND +#define MIN_PACKET_SIZE (64) + char loopback_tx_pkt[MIN_PACKET_SIZE]; + char loopback_rx_pkt[MIN_PACKET_SIZE]; + unsigned int resetcount; +#endif + + /* Members for Multicast filter workaround */ + unsigned int multicast_update_pending; + unsigned int set_bits_mask; + unsigned int clear_bits_mask; + unsigned int hashhi; + unsigned int hashlo; +}; + +#if SMSC_CAN_USE_32BIT + +static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg) +{ + return readl(pdata->ioaddr + reg); +} + +static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg, + u32 val) +{ + writel(val, pdata->ioaddr + reg); +} + +/* Writes a packet to the TX_DATA_FIFO */ +static inline void +smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf, + unsigned int wordcount) +{ + writesl(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount); +} + +/* Reads a packet out of the RX_DATA_FIFO */ +static inline void +smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf, + unsigned int wordcount) +{ + readsl(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount); +} + +#else /* SMSC_CAN_USE_32BIT */ + +/* These 16-bit access functions are significantly slower, due to the locking + * necessary. If your bus hardware can be configured to do this for you + * (in response to a single 32-bit operation from software), you should use + * the 32-bit access functions instead. */ + +static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg) +{ + unsigned long flags; + u32 data; + + /* these two 16-bit reads must be performed consecutively, so must + * not be interrupted by our own ISR (which would start another + * read operation) */ + spin_lock_irqsave(&pdata->dev_lock, flags); + data = ((readw(pdata->ioaddr + reg) & 0xFFFF) | + ((readw(pdata->ioaddr + reg + 2) & 0xFFFF) << 16)); + spin_unlock_irqrestore(&pdata->dev_lock, flags); + + return data; +} + +static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg, + u32 val) +{ + unsigned long flags; + + /* these two 16-bit writes must be performed consecutively, so must + * not be interrupted by our own ISR (which would start another + * read operation) */ + spin_lock_irqsave(&pdata->dev_lock, flags); + writew(val & 0xFFFF, pdata->ioaddr + reg); + writew((val >> 16) & 0xFFFF, pdata->ioaddr + reg + 2); + spin_unlock_irqrestore(&pdata->dev_lock, flags); +} + +/* Writes a packet to the TX_DATA_FIFO */ +static inline void +smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf, + unsigned int wordcount) +{ + while (wordcount--) + smsc911x_reg_write(pdata, TX_DATA_FIFO, *buf++); +} + +/* Reads a packet out of the RX_DATA_FIFO */ +static inline void +smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf, + unsigned int wordcount) +{ + while (wordcount--) + *buf++ = smsc911x_reg_read(pdata, RX_DATA_FIFO); +} + +#endif /* SMSC_CAN_USE_32BIT */ + +/* waits for MAC not busy, with timeout. Only called by smsc911x_mac_read + * and smsc911x_mac_write, so assumes mac_lock is held */ +static int smsc911x_mac_complete(struct smsc911x_data *pdata) +{ + int i; + u32 val; + + SMSC_ASSERT_MAC_LOCK(pdata); + + for (i = 0; i < 40; i++) { + val = smsc911x_reg_read(pdata, MAC_CSR_CMD); + if (!(val & MAC_CSR_CMD_CSR_BUSY_)) + return 0; + } + SMSC_WARNING(HW, "Timed out waiting for MAC not BUSY. " + "MAC_CSR_CMD: 0x%08X", val); + return -EIO; +} + +/* Fetches a MAC register value. Assumes mac_lock is acquired */ +static u32 smsc911x_mac_read(struct smsc911x_data *pdata, unsigned int offset) +{ + unsigned int temp; + + SMSC_ASSERT_MAC_LOCK(pdata); + + temp = smsc911x_reg_read(pdata, MAC_CSR_CMD); + if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) { + SMSC_WARNING(HW, "MAC busy at entry"); + return 0xFFFFFFFF; + } + + /* Send the MAC cmd */ + smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) | + MAC_CSR_CMD_CSR_BUSY_ | MAC_CSR_CMD_R_NOT_W_)); + + /* Workaround for hardware read-after-write restriction */ + temp = smsc911x_reg_read(pdata, BYTE_TEST); + + /* Wait for the read to complete */ + if (likely(smsc911x_mac_complete(pdata) == 0)) + return smsc911x_reg_read(pdata, MAC_CSR_DATA); + + SMSC_WARNING(HW, "MAC busy after read"); + return 0xFFFFFFFF; +} + +/* Set a mac register, mac_lock must be acquired before calling */ +static void smsc911x_mac_write(struct smsc911x_data *pdata, + unsigned int offset, u32 val) +{ + unsigned int temp; + + SMSC_ASSERT_MAC_LOCK(pdata); + + temp = smsc911x_reg_read(pdata, MAC_CSR_CMD); + if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) { + SMSC_WARNING(HW, + "smsc911x_mac_write failed, MAC busy at entry"); + return; + } + + /* Send data to write */ + smsc911x_reg_write(pdata, MAC_CSR_DATA, val); + + /* Write the actual data */ + smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) | + MAC_CSR_CMD_CSR_BUSY_)); + + /* Workaround for hardware read-after-write restriction */ + temp = smsc911x_reg_read(pdata, BYTE_TEST); + + /* Wait for the write to complete */ + if (likely(smsc911x_mac_complete(pdata) == 0)) + return; + + SMSC_WARNING(HW, + "smsc911x_mac_write failed, MAC busy after write"); +} + +/* Get a phy register */ +static int smsc911x_mii_read(struct mii_bus *bus, int phyaddr, int regidx) +{ + struct smsc911x_data *pdata = (struct smsc911x_data *)bus->priv; + unsigned long flags; + unsigned int addr; + int i, reg; + + spin_lock_irqsave(&pdata->mac_lock, flags); + + /* Confirm MII not busy */ + if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { + SMSC_WARNING(HW, + "MII is busy in smsc911x_mii_read???"); + reg = -EIO; + goto out; + } + + /* Set the address, index & direction (read from PHY) */ + addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6); + smsc911x_mac_write(pdata, MII_ACC, addr); + + /* Wait for read to complete w/ timeout */ + for (i = 0; i < 100; i++) + if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { + reg = smsc911x_mac_read(pdata, MII_DATA); + goto out; + } + + SMSC_WARNING(HW, "Timed out waiting for MII write to finish"); + reg = -EIO; + +out: + spin_unlock_irqrestore(&pdata->mac_lock, flags); + return reg; +} + +/* Set a phy register */ +static int smsc911x_mii_write(struct mii_bus *bus, int phyaddr, int regidx, + u16 val) +{ + struct smsc911x_data *pdata = (struct smsc911x_data *)bus->priv; + unsigned long flags; + unsigned int addr; + int i, reg; + + spin_lock_irqsave(&pdata->mac_lock, flags); + + /* Confirm MII not busy */ + if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { + SMSC_WARNING(HW, + "MII is busy in smsc911x_mii_write???"); + reg = -EIO; + goto out; + } + + /* Put the data to write in the MAC */ + smsc911x_mac_write(pdata, MII_DATA, val); + + /* Set the address, index & direction (write to PHY) */ + addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6) | + MII_ACC_MII_WRITE_; + smsc911x_mac_write(pdata, MII_ACC, addr); + + /* Wait for write to complete w/ timeout */ + for (i = 0; i < 100; i++) + if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { + reg = 0; + goto out; + } + + SMSC_WARNING(HW, "Timed out waiting for MII write to finish"); + reg = -EIO; + +out: + spin_unlock_irqrestore(&pdata->mac_lock, flags); + return reg; +} + +/* Autodetects and initialises external phy for SMSC9115 and SMSC9117 flavors. + * If something goes wrong, returns -ENODEV to revert back to internal phy. + * Performed at initialisation only, so interrupts are enabled */ +static int smsc911x_phy_initialise_external(struct smsc911x_data *pdata) +{ + unsigned int hwcfg = smsc911x_reg_read(pdata, HW_CFG); + + /* External phy is requested, supported, and detected */ + if (hwcfg & HW_CFG_EXT_PHY_DET_) { + + /* Switch to external phy. Assuming tx and rx are stopped + * because smsc911x_phy_initialise is called before + * smsc911x_rx_initialise and tx_initialise. */ + + /* Disable phy clocks to the MAC */ + hwcfg &= (~HW_CFG_PHY_CLK_SEL_); + hwcfg |= HW_CFG_PHY_CLK_SEL_CLK_DIS_; + smsc911x_reg_write(pdata, HW_CFG, hwcfg); + udelay(10); /* Enough time for clocks to stop */ + + /* Switch to external phy */ + hwcfg |= HW_CFG_EXT_PHY_EN_; + smsc911x_reg_write(pdata, HW_CFG, hwcfg); + + /* Enable phy clocks to the MAC */ + hwcfg &= (~HW_CFG_PHY_CLK_SEL_); + hwcfg |= HW_CFG_PHY_CLK_SEL_EXT_PHY_; + smsc911x_reg_write(pdata, HW_CFG, hwcfg); + udelay(10); /* Enough time for clocks to restart */ + + hwcfg |= HW_CFG_SMI_SEL_; + smsc911x_reg_write(pdata, HW_CFG, hwcfg); + + SMSC_TRACE(HW, "Successfully switched to external PHY"); + pdata->using_extphy = 1; + } else { + SMSC_WARNING(HW, "No external PHY detected, " + "Using internal PHY instead."); + /* Use internal phy */ + return -ENODEV; + } + return 0; +} + +/* Fetches a tx status out of the status fifo */ +static unsigned int smsc911x_tx_get_txstatus(struct smsc911x_data *pdata) +{ + unsigned int result = + smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TSUSED_; + + if (result != 0) + result = smsc911x_reg_read(pdata, TX_STATUS_FIFO); + + return result; +} + +/* Fetches the next rx status */ +static unsigned int smsc911x_rx_get_rxstatus(struct smsc911x_data *pdata) +{ + unsigned int result = + smsc911x_reg_read(pdata, RX_FIFO_INF) & RX_FIFO_INF_RXSUSED_; + + if (result != 0) + result = smsc911x_reg_read(pdata, RX_STATUS_FIFO); + + return result; +} + +#ifdef USE_PHY_WORK_AROUND +static int smsc911x_phy_check_loopbackpkt(struct smsc911x_data *pdata) +{ + unsigned int tries; + u32 wrsz; + u32 rdsz; + ulong bufp; + + for (tries = 0; tries < 10; tries++) { + unsigned int txcmd_a; + unsigned int txcmd_b; + unsigned int status; + unsigned int pktlength; + unsigned int i; + + /* Zero-out rx packet memory */ + memset(pdata->loopback_rx_pkt, 0, MIN_PACKET_SIZE); + + /* Write tx packet to 118 */ + txcmd_a = (u32)((ulong)pdata->loopback_tx_pkt & 0x03) << 16; + txcmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_; + txcmd_a |= MIN_PACKET_SIZE; + + txcmd_b = MIN_PACKET_SIZE << 16 | MIN_PACKET_SIZE; + + smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_a); + smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_b); + + bufp = (ulong)pdata->loopback_tx_pkt & (~0x3); + wrsz = MIN_PACKET_SIZE + 3; + wrsz += (u32)((ulong)pdata->loopback_tx_pkt & 0x3); + wrsz >>= 2; + + smsc911x_tx_writefifo(pdata, (unsigned int *)bufp, wrsz); + + /* Wait till transmit is done */ + i = 60; + do { + udelay(5); + status = smsc911x_tx_get_txstatus(pdata); + } while ((i--) && (!status)); + + if (!status) { + SMSC_WARNING(HW, "Failed to transmit " + "during loopback test"); + continue; + } + if (status & TX_STS_ES_) { + SMSC_WARNING(HW, "Transmit encountered " + "errors during loopback test"); + continue; + } + + /* Wait till receive is done */ + i = 60; + do { + udelay(5); + status = smsc911x_rx_get_rxstatus(pdata); + } while ((i--) && (!status)); + + if (!status) { + SMSC_WARNING(HW, + "Failed to receive during loopback test"); + continue; + } + if (status & RX_STS_ES_) { + SMSC_WARNING(HW, "Receive encountered " + "errors during loopback test"); + continue; + } + + pktlength = ((status & 0x3FFF0000UL) >> 16); + bufp = (ulong)pdata->loopback_rx_pkt; + rdsz = pktlength + 3; + rdsz += (u32)((ulong)pdata->loopback_rx_pkt & 0x3); + rdsz >>= 2; + + smsc911x_rx_readfifo(pdata, (unsigned int *)bufp, rdsz); + + if (pktlength != (MIN_PACKET_SIZE + 4)) { + SMSC_WARNING(HW, "Unexpected packet size " + "during loop back test, size=%d, will retry", + pktlength); + } else { + unsigned int j; + int mismatch = 0; + for (j = 0; j < MIN_PACKET_SIZE; j++) { + if (pdata->loopback_tx_pkt[j] + != pdata->loopback_rx_pkt[j]) { + mismatch = 1; + break; + } + } + if (!mismatch) { + SMSC_TRACE(HW, "Successfully verified " + "loopback packet"); + return 0; + } else { + SMSC_WARNING(HW, "Data mismatch " + "during loop back test, will retry"); + } + } + } + + return -EIO; +} + +static int smsc911x_phy_reset(struct smsc911x_data *pdata) +{ + struct phy_device *phy_dev = pdata->phy_dev; + unsigned int temp; + unsigned int i = 100000; + + BUG_ON(!phy_dev); + BUG_ON(!phy_dev->bus); + + SMSC_TRACE(HW, "Performing PHY BCR Reset"); + smsc911x_mii_write(phy_dev->bus, phy_dev->addr, MII_BMCR, BMCR_RESET); + do { + msleep(1); + temp = smsc911x_mii_read(phy_dev->bus, phy_dev->addr, + MII_BMCR); + } while ((i--) && (temp & BMCR_RESET)); + + if (temp & BMCR_RESET) { + SMSC_WARNING(HW, "PHY reset failed to complete."); + return -EIO; + } + /* Extra delay required because the phy may not be completed with + * its reset when BMCR_RESET is cleared. Specs say 256 uS is + * enough delay but using 1ms here to be safe */ + msleep(1); + + return 0; +} + +static int smsc911x_phy_loopbacktest(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + struct phy_device *phy_dev = pdata->phy_dev; + int result = -EIO; + unsigned int i, val; + unsigned long flags; + + /* Initialise tx packet using broadcast destination address */ + memset(pdata->loopback_tx_pkt, 0xff, ETH_ALEN); + + /* Use incrementing source address */ + for (i = 6; i < 12; i++) + pdata->loopback_tx_pkt[i] = (char)i; + + /* Set length type field */ + pdata->loopback_tx_pkt[12] = 0x00; + pdata->loopback_tx_pkt[13] = 0x00; + + for (i = 14; i < MIN_PACKET_SIZE; i++) + pdata->loopback_tx_pkt[i] = (char)i; + + val = smsc911x_reg_read(pdata, HW_CFG); + val &= HW_CFG_TX_FIF_SZ_; + val |= HW_CFG_SF_; + smsc911x_reg_write(pdata, HW_CFG, val); + + smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_); + smsc911x_reg_write(pdata, RX_CFG, + (u32)((ulong)pdata->loopback_rx_pkt & 0x03) << 8); + + for (i = 0; i < 10; i++) { + /* Set PHY to 10/FD, no ANEG, and loopback mode */ + smsc911x_mii_write(phy_dev->bus, phy_dev->addr, MII_BMCR, + BMCR_LOOPBACK | BMCR_FULLDPLX); + + /* Enable MAC tx/rx, FD */ + spin_lock_irqsave(&pdata->mac_lock, flags); + smsc911x_mac_write(pdata, MAC_CR, MAC_CR_FDPX_ + | MAC_CR_TXEN_ | MAC_CR_RXEN_); + spin_unlock_irqrestore(&pdata->mac_lock, flags); + + if (smsc911x_phy_check_loopbackpkt(pdata) == 0) { + result = 0; + break; + } + pdata->resetcount++; + + /* Disable MAC rx */ + spin_lock_irqsave(&pdata->mac_lock, flags); + smsc911x_mac_write(pdata, MAC_CR, 0); + spin_unlock_irqrestore(&pdata->mac_lock, flags); + + smsc911x_phy_reset(pdata); + } + + /* Disable MAC */ + spin_lock_irqsave(&pdata->mac_lock, flags); + smsc911x_mac_write(pdata, MAC_CR, 0); + spin_unlock_irqrestore(&pdata->mac_lock, flags); + + /* Cancel PHY loopback mode */ + smsc911x_mii_write(phy_dev->bus, phy_dev->addr, MII_BMCR, 0); + + smsc911x_reg_write(pdata, TX_CFG, 0); + smsc911x_reg_write(pdata, RX_CFG, 0); + + return result; +} +#endif /* USE_PHY_WORK_AROUND */ + +static u8 smsc95xx_resolve_flowctrl_fulldplx(u16 lcladv, u16 rmtadv) +{ + u8 cap = 0; + + if (lcladv & ADVERTISE_PAUSE_CAP) { + if (lcladv & ADVERTISE_PAUSE_ASYM) { + if (rmtadv & LPA_PAUSE_CAP) + cap = FLOW_CTRL_TX | FLOW_CTRL_RX; + else if (rmtadv & LPA_PAUSE_ASYM) + cap = FLOW_CTRL_RX; + } else { + if (rmtadv & LPA_PAUSE_CAP) + cap = FLOW_CTRL_TX | FLOW_CTRL_RX; + } + } else if (lcladv & ADVERTISE_PAUSE_ASYM) { + if ((rmtadv & LPA_PAUSE_CAP) && (rmtadv & LPA_PAUSE_ASYM)) + cap = FLOW_CTRL_TX; + } + + return cap; +} + +static void smsc911x_phy_update_flowcontrol(struct smsc911x_data *pdata) +{ + struct phy_device *phy_dev = pdata->phy_dev; + u32 afc = smsc911x_reg_read(pdata, AFC_CFG); + u32 flow; + unsigned long flags; + + if (phy_dev->duplex == DUPLEX_FULL) { + u16 lcladv = phy_read(phy_dev, MII_ADVERTISE); + u16 rmtadv = phy_read(phy_dev, MII_LPA); + u8 cap = smsc95xx_resolve_flowctrl_fulldplx(lcladv, rmtadv); + + if (cap & FLOW_CTRL_RX) + flow = 0xFFFF0002; + else + flow = 0; + + if (cap & FLOW_CTRL_TX) + afc |= 0xF; + else + afc &= ~0xF; + + SMSC_TRACE(HW, "rx pause %s, tx pause %s", + (cap & FLOW_CTRL_RX ? "enabled" : "disabled"), + (cap & FLOW_CTRL_TX ? "enabled" : "disabled")); + } else { + SMSC_TRACE(HW, "half duplex"); + flow = 0; + afc |= 0xF; + } + + spin_lock_irqsave(&pdata->mac_lock, flags); + smsc911x_mac_write(pdata, FLOW, flow); + spin_unlock_irqrestore(&pdata->mac_lock, flags); + + smsc911x_reg_write(pdata, AFC_CFG, afc); +} + +/* Update link mode if anything has changed. Called periodically when the + * PHY is in polling mode, even if nothing has changed. */ +static void smsc911x_phy_adjust_link(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + struct phy_device *phy_dev = pdata->phy_dev; + unsigned long flags; + int carrier; + + if (phy_dev->duplex != pdata->last_duplex) { + unsigned int mac_cr; + SMSC_TRACE(HW, "duplex state has changed"); + + spin_lock_irqsave(&pdata->mac_lock, flags); + mac_cr = smsc911x_mac_read(pdata, MAC_CR); + if (phy_dev->duplex) { + SMSC_TRACE(HW, + "configuring for full duplex mode"); + mac_cr |= MAC_CR_FDPX_; + } else { + SMSC_TRACE(HW, + "configuring for half duplex mode"); + mac_cr &= ~MAC_CR_FDPX_; + } + smsc911x_mac_write(pdata, MAC_CR, mac_cr); + spin_unlock_irqrestore(&pdata->mac_lock, flags); + + smsc911x_phy_update_flowcontrol(pdata); + pdata->last_duplex = phy_dev->duplex; + } + + carrier = netif_carrier_ok(dev); + if (carrier != pdata->last_carrier) { + SMSC_TRACE(HW, "carrier state has changed"); + if (carrier) { + SMSC_TRACE(HW, "configuring for carrier OK"); + if ((pdata->gpio_orig_setting & GPIO_CFG_LED1_EN_) && + (!pdata->using_extphy)) { + /* Restore orginal GPIO configuration */ + pdata->gpio_setting = pdata->gpio_orig_setting; + smsc911x_reg_write(pdata, GPIO_CFG, + pdata->gpio_setting); + } + } else { + SMSC_TRACE(HW, "configuring for no carrier"); + /* Check global setting that LED1 + * usage is 10/100 indicator */ + pdata->gpio_setting = smsc911x_reg_read(pdata, + GPIO_CFG); + if ((pdata->gpio_setting & GPIO_CFG_LED1_EN_) + && (!pdata->using_extphy)) { + /* Force 10/100 LED off, after saving + * orginal GPIO configuration */ + pdata->gpio_orig_setting = pdata->gpio_setting; + + pdata->gpio_setting &= ~GPIO_CFG_LED1_EN_; + pdata->gpio_setting |= (GPIO_CFG_GPIOBUF0_ + | GPIO_CFG_GPIODIR0_ + | GPIO_CFG_GPIOD0_); + smsc911x_reg_write(pdata, GPIO_CFG, + pdata->gpio_setting); + } + } + pdata->last_carrier = carrier; + } +} + +static int smsc911x_mii_probe(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + struct phy_device *phydev = NULL; + int phy_addr; + + /* find the first phy */ + for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++) { + if (pdata->mii_bus->phy_map[phy_addr]) { + phydev = pdata->mii_bus->phy_map[phy_addr]; + SMSC_TRACE(PROBE, "PHY %d: addr %d, phy_id 0x%08X", + phy_addr, phydev->addr, phydev->phy_id); + break; + } + } + + if (!phydev) { + pr_err("%s: no PHY found\n", dev->name); + return -ENODEV; + } + + phydev = phy_connect(dev, phydev->dev.bus_id, + &smsc911x_phy_adjust_link, 0, pdata->phy_interface); + + if (IS_ERR(phydev)) { + pr_err("%s: Could not attach to PHY\n", dev->name); + return PTR_ERR(phydev); + } + + pr_info("%s: attached PHY driver [%s] (mii_bus:phy_addr=%s, irq=%d)\n", + dev->name, phydev->drv->name, phydev->dev.bus_id, phydev->irq); + + /* mask with MAC supported features */ + phydev->supported &= (PHY_BASIC_FEATURES | SUPPORTED_Pause | + SUPPORTED_Asym_Pause); + phydev->advertising = phydev->supported; + + pdata->phy_dev = phydev; + pdata->last_duplex = -1; + pdata->last_carrier = -1; + +#ifdef USE_PHY_WORK_AROUND + if (smsc911x_phy_loopbacktest(dev) < 0) { + SMSC_WARNING(HW, "Failed Loop Back Test"); + return -ENODEV; + } + SMSC_TRACE(HW, "Passed Loop Back Test"); +#endif /* USE_PHY_WORK_AROUND */ + + SMSC_TRACE(HW, "phy initialised succesfully"); + return 0; +} + +static int __devinit smsc911x_mii_init(struct platform_device *pdev, + struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + int err = -ENXIO, i; + + pdata->mii_bus = mdiobus_alloc(); + if (!pdata->mii_bus) { + err = -ENOMEM; + goto err_out_1; + } + + pdata->mii_bus->name = SMSC_MDIONAME; + snprintf(pdata->mii_bus->id, MII_BUS_ID_SIZE, "%x", pdev->id); + pdata->mii_bus->priv = pdata; + pdata->mii_bus->read = smsc911x_mii_read; + pdata->mii_bus->write = smsc911x_mii_write; + pdata->mii_bus->irq = pdata->phy_irq; + for (i = 0; i < PHY_MAX_ADDR; ++i) + pdata->mii_bus->irq[i] = PHY_POLL; + + pdata->mii_bus->parent = &pdev->dev; + dev_set_drvdata(&pdev->dev, &pdata->mii_bus); + + pdata->using_extphy = 0; + + switch (pdata->idrev & 0xFFFF0000) { + case 0x01170000: + case 0x01150000: + case 0x117A0000: + case 0x115A0000: + /* External PHY supported, try to autodetect */ + if (smsc911x_phy_initialise_external(pdata) < 0) { + SMSC_TRACE(HW, "No external PHY detected, " + "using internal PHY"); + } + break; + default: + SMSC_TRACE(HW, "External PHY is not supported, " + "using internal PHY"); + break; + } + + if (!pdata->using_extphy) { + /* Mask all PHYs except ID 1 (internal) */ + pdata->mii_bus->phy_mask = ~(1 << 1); + } + + if (mdiobus_register(pdata->mii_bus)) { + SMSC_WARNING(PROBE, "Error registering mii bus"); + goto err_out_free_bus_2; + } + + if (smsc911x_mii_probe(dev) < 0) { + SMSC_WARNING(PROBE, "Error registering mii bus"); + goto err_out_unregister_bus_3; + } + + return 0; + +err_out_unregister_bus_3: + mdiobus_unregister(pdata->mii_bus); +err_out_free_bus_2: + mdiobus_free(pdata->mii_bus); +err_out_1: + return err; +} + +/* Gets the number of tx statuses in the fifo */ +static unsigned int smsc911x_tx_get_txstatcount(struct smsc911x_data *pdata) +{ + return (smsc911x_reg_read(pdata, TX_FIFO_INF) + & TX_FIFO_INF_TSUSED_) >> 16; +} + +/* Reads tx statuses and increments counters where necessary */ +static void smsc911x_tx_update_txcounters(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + unsigned int tx_stat; + + while ((tx_stat = smsc911x_tx_get_txstatus(pdata)) != 0) { + if (unlikely(tx_stat & 0x80000000)) { + /* In this driver the packet tag is used as the packet + * length. Since a packet length can never reach the + * size of 0x8000, this bit is reserved. It is worth + * noting that the "reserved bit" in the warning above + * does not reference a hardware defined reserved bit + * but rather a driver defined one. + */ + SMSC_WARNING(HW, + "Packet tag reserved bit is high"); + } else { + if (unlikely(tx_stat & 0x00008000)) { + dev->stats.tx_errors++; + } else { + dev->stats.tx_packets++; + dev->stats.tx_bytes += (tx_stat >> 16); + } + if (unlikely(tx_stat & 0x00000100)) { + dev->stats.collisions += 16; + dev->stats.tx_aborted_errors += 1; + } else { + dev->stats.collisions += + ((tx_stat >> 3) & 0xF); + } + if (unlikely(tx_stat & 0x00000800)) + dev->stats.tx_carrier_errors += 1; + if (unlikely(tx_stat & 0x00000200)) { + dev->stats.collisions++; + dev->stats.tx_aborted_errors++; + } + } + } +} + +/* Increments the Rx error counters */ +static void +smsc911x_rx_counterrors(struct net_device *dev, unsigned int rxstat) +{ + int crc_err = 0; + + if (unlikely(rxstat & 0x00008000)) { + dev->stats.rx_errors++; + if (unlikely(rxstat & 0x00000002)) { + dev->stats.rx_crc_errors++; + crc_err = 1; + } + } + if (likely(!crc_err)) { + if (unlikely((rxstat & 0x00001020) == 0x00001020)) { + /* Frame type indicates length, + * and length error is set */ + dev->stats.rx_length_errors++; + } + if (rxstat & RX_STS_MCAST_) + dev->stats.multicast++; + } +} + +/* Quickly dumps bad packets */ +static void +smsc911x_rx_fastforward(struct smsc911x_data *pdata, unsigned int pktbytes) +{ + unsigned int pktwords = (pktbytes + NET_IP_ALIGN + 3) >> 2; + + if (likely(pktwords >= 4)) { + unsigned int timeout = 500; + unsigned int val; + smsc911x_reg_write(pdata, RX_DP_CTRL, RX_DP_CTRL_RX_FFWD_); + do { + udelay(1); + val = smsc911x_reg_read(pdata, RX_DP_CTRL); + } while (timeout-- && (val & RX_DP_CTRL_RX_FFWD_)); + + if (unlikely(timeout == 0)) + SMSC_WARNING(HW, "Timed out waiting for " + "RX FFWD to finish, RX_DP_CTRL: 0x%08X", val); + } else { + unsigned int temp; + while (pktwords--) + temp = smsc911x_reg_read(pdata, RX_DATA_FIFO); + } +} + +/* NAPI poll function */ +static int smsc911x_poll(struct napi_struct *napi, int budget) +{ + struct smsc911x_data *pdata = + container_of(napi, struct smsc911x_data, napi); + struct net_device *dev = pdata->dev; + int npackets = 0; + + while (likely(netif_running(dev)) && (npackets < budget)) { + unsigned int pktlength; + unsigned int pktwords; + struct sk_buff *skb; + unsigned int rxstat = smsc911x_rx_get_rxstatus(pdata); + + if (!rxstat) { + unsigned int temp; + /* We processed all packets available. Tell NAPI it can + * stop polling then re-enable rx interrupts */ + smsc911x_reg_write(pdata, INT_STS, INT_STS_RSFL_); + netif_rx_complete(dev, napi); + temp = smsc911x_reg_read(pdata, INT_EN); + temp |= INT_EN_RSFL_EN_; + smsc911x_reg_write(pdata, INT_EN, temp); + break; + } + + /* Count packet for NAPI scheduling, even if it has an error. + * Error packets still require cycles to discard */ + npackets++; + + pktlength = ((rxstat & 0x3FFF0000) >> 16); + pktwords = (pktlength + NET_IP_ALIGN + 3) >> 2; + smsc911x_rx_counterrors(dev, rxstat); + + if (unlikely(rxstat & RX_STS_ES_)) { + SMSC_WARNING(RX_ERR, + "Discarding packet with error bit set"); + /* Packet has an error, discard it and continue with + * the next */ + smsc911x_rx_fastforward(pdata, pktwords); + dev->stats.rx_dropped++; + continue; + } + + skb = netdev_alloc_skb(dev, pktlength + NET_IP_ALIGN); + if (unlikely(!skb)) { + SMSC_WARNING(RX_ERR, + "Unable to allocate skb for rx packet"); + /* Drop the packet and stop this polling iteration */ + smsc911x_rx_fastforward(pdata, pktwords); + dev->stats.rx_dropped++; + break; + } + + skb->data = skb->head; + skb_reset_tail_pointer(skb); + + /* Align IP on 16B boundary */ + skb_reserve(skb, NET_IP_ALIGN); + skb_put(skb, pktlength - 4); + smsc911x_rx_readfifo(pdata, (unsigned int *)skb->head, + pktwords); + skb->protocol = eth_type_trans(skb, dev); + skb->ip_summed = CHECKSUM_NONE; + netif_receive_skb(skb); + + /* Update counters */ + dev->stats.rx_packets++; + dev->stats.rx_bytes += (pktlength - 4); + dev->last_rx = jiffies; + } + + /* Return total received packets */ + return npackets; +} + +/* Returns hash bit number for given MAC address + * Example: + * 01 00 5E 00 00 01 -> returns bit number 31 */ +static unsigned int smsc911x_hash(char addr[ETH_ALEN]) +{ + return (ether_crc(ETH_ALEN, addr) >> 26) & 0x3f; +} + +static void smsc911x_rx_multicast_update(struct smsc911x_data *pdata) +{ + /* Performs the multicast & mac_cr update. This is called when + * safe on the current hardware, and with the mac_lock held */ + unsigned int mac_cr; + + SMSC_ASSERT_MAC_LOCK(pdata); + + mac_cr = smsc911x_mac_read(pdata, MAC_CR); + mac_cr |= pdata->set_bits_mask; + mac_cr &= ~(pdata->clear_bits_mask); + smsc911x_mac_write(pdata, MAC_CR, mac_cr); + smsc911x_mac_write(pdata, HASHH, pdata->hashhi); + smsc911x_mac_write(pdata, HASHL, pdata->hashlo); + SMSC_TRACE(HW, "maccr 0x%08X, HASHH 0x%08X, HASHL 0x%08X", + mac_cr, pdata->hashhi, pdata->hashlo); +} + +static void smsc911x_rx_multicast_update_workaround(struct smsc911x_data *pdata) +{ + unsigned int mac_cr; + + /* This function is only called for older LAN911x devices + * (revA or revB), where MAC_CR, HASHH and HASHL should not + * be modified during Rx - newer devices immediately update the + * registers. + * + * This is called from interrupt context */ + + spin_lock(&pdata->mac_lock); + + /* Check Rx has stopped */ + if (smsc911x_mac_read(pdata, MAC_CR) & MAC_CR_RXEN_) + SMSC_WARNING(DRV, "Rx not stopped"); + + /* Perform the update - safe to do now Rx has stopped */ + smsc911x_rx_multicast_update(pdata); + + /* Re-enable Rx */ + mac_cr = smsc911x_mac_read(pdata, MAC_CR); + mac_cr |= MAC_CR_RXEN_; + smsc911x_mac_write(pdata, MAC_CR, mac_cr); + + pdata->multicast_update_pending = 0; + + spin_unlock(&pdata->mac_lock); +} + +static int smsc911x_soft_reset(struct smsc911x_data *pdata) +{ + unsigned int timeout; + unsigned int temp; + + /* Reset the LAN911x */ + smsc911x_reg_write(pdata, HW_CFG, HW_CFG_SRST_); + timeout = 10; + do { + udelay(10); + temp = smsc911x_reg_read(pdata, HW_CFG); + } while ((--timeout) && (temp & HW_CFG_SRST_)); + + if (unlikely(temp & HW_CFG_SRST_)) { + SMSC_WARNING(DRV, "Failed to complete reset"); + return -EIO; + } + return 0; +} + +/* Sets the device MAC address to dev_addr, called with mac_lock held */ +static void +smsc911x_set_mac_address(struct smsc911x_data *pdata, u8 dev_addr[6]) +{ + u32 mac_high16 = (dev_addr[5] << 8) | dev_addr[4]; + u32 mac_low32 = (dev_addr[3] << 24) | (dev_addr[2] << 16) | + (dev_addr[1] << 8) | dev_addr[0]; + + SMSC_ASSERT_MAC_LOCK(pdata); + + smsc911x_mac_write(pdata, ADDRH, mac_high16); + smsc911x_mac_write(pdata, ADDRL, mac_low32); +} + +static int smsc911x_open(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + unsigned int timeout; + unsigned int temp; + unsigned int intcfg; + + /* if the phy is not yet registered, retry later*/ + if (!pdata->phy_dev) { + SMSC_WARNING(HW, "phy_dev is NULL"); + return -EAGAIN; + } + + if (!is_valid_ether_addr(dev->dev_addr)) { + SMSC_WARNING(HW, "dev_addr is not a valid MAC address"); + return -EADDRNOTAVAIL; + } + + /* Reset the LAN911x */ + if (smsc911x_soft_reset(pdata)) { + SMSC_WARNING(HW, "soft reset failed"); + return -EIO; + } + + smsc911x_reg_write(pdata, HW_CFG, 0x00050000); + smsc911x_reg_write(pdata, AFC_CFG, 0x006E3740); + + /* Make sure EEPROM has finished loading before setting GPIO_CFG */ + timeout = 50; + while ((timeout--) && + (smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_)) { + udelay(10); + } + + if (unlikely(timeout == 0)) + SMSC_WARNING(IFUP, + "Timed out waiting for EEPROM busy bit to clear"); + + smsc911x_reg_write(pdata, GPIO_CFG, 0x70070000); + + /* The soft reset above cleared the device's MAC address, + * restore it from local copy (set in probe) */ + spin_lock_irq(&pdata->mac_lock); + smsc911x_set_mac_address(pdata, dev->dev_addr); + spin_unlock_irq(&pdata->mac_lock); + + /* Initialise irqs, but leave all sources disabled */ + smsc911x_reg_write(pdata, INT_EN, 0); + smsc911x_reg_write(pdata, INT_STS, 0xFFFFFFFF); + + /* Set interrupt deassertion to 100uS */ + intcfg = ((10 << 24) | INT_CFG_IRQ_EN_); + + if (pdata->irq_polarity) { + SMSC_TRACE(IFUP, "irq polarity: active high"); + intcfg |= INT_CFG_IRQ_POL_; + } else { + SMSC_TRACE(IFUP, "irq polarity: active low"); + } + + if (pdata->irq_type) { + SMSC_TRACE(IFUP, "irq type: push-pull"); + intcfg |= INT_CFG_IRQ_TYPE_; + } else { + SMSC_TRACE(IFUP, "irq type: open drain"); + } + + smsc911x_reg_write(pdata, INT_CFG, intcfg); + + SMSC_TRACE(IFUP, "Testing irq handler using IRQ %d", dev->irq); + pdata->software_irq_signal = 0; + smp_wmb(); + + temp = smsc911x_reg_read(pdata, INT_EN); + temp |= INT_EN_SW_INT_EN_; + smsc911x_reg_write(pdata, INT_EN, temp); + + timeout = 1000; + while (timeout--) { + if (pdata->software_irq_signal) + break; + msleep(1); + } + + if (!pdata->software_irq_signal) { + dev_warn(&dev->dev, "ISR failed signaling test (IRQ %d)\n", + dev->irq); + return -ENODEV; + } + SMSC_TRACE(IFUP, "IRQ handler passed test using IRQ %d", dev->irq); + + dev_info(&dev->dev, "SMSC911x/921x identified at %#08lx, IRQ: %d\n", + (unsigned long)pdata->ioaddr, dev->irq); + + /* Bring the PHY up */ + phy_start(pdata->phy_dev); + + temp = smsc911x_reg_read(pdata, HW_CFG); + /* Preserve TX FIFO size and external PHY configuration */ + temp &= (HW_CFG_TX_FIF_SZ_|0x00000FFF); + temp |= HW_CFG_SF_; + smsc911x_reg_write(pdata, HW_CFG, temp); + + temp = smsc911x_reg_read(pdata, FIFO_INT); + temp |= FIFO_INT_TX_AVAIL_LEVEL_; + temp &= ~(FIFO_INT_RX_STS_LEVEL_); + smsc911x_reg_write(pdata, FIFO_INT, temp); + + /* set RX Data offset to 2 bytes for alignment */ + smsc911x_reg_write(pdata, RX_CFG, (2 << 8)); + + /* enable NAPI polling before enabling RX interrupts */ + napi_enable(&pdata->napi); + + temp = smsc911x_reg_read(pdata, INT_EN); + temp |= (INT_EN_TDFA_EN_ | INT_EN_RSFL_EN_); + smsc911x_reg_write(pdata, INT_EN, temp); + + spin_lock_irq(&pdata->mac_lock); + temp = smsc911x_mac_read(pdata, MAC_CR); + temp |= (MAC_CR_TXEN_ | MAC_CR_RXEN_ | MAC_CR_HBDIS_); + smsc911x_mac_write(pdata, MAC_CR, temp); + spin_unlock_irq(&pdata->mac_lock); + + smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_); + + netif_start_queue(dev); + return 0; +} + +/* Entry point for stopping the interface */ +static int smsc911x_stop(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + unsigned int temp; + + BUG_ON(!pdata->phy_dev); + + /* Disable all device interrupts */ + temp = smsc911x_reg_read(pdata, INT_CFG); + temp &= ~INT_CFG_IRQ_EN_; + smsc911x_reg_write(pdata, INT_CFG, temp); + + /* Stop Tx and Rx polling */ + netif_stop_queue(dev); + napi_disable(&pdata->napi); + + /* At this point all Rx and Tx activity is stopped */ + dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP); + smsc911x_tx_update_txcounters(dev); + + /* Bring the PHY down */ + phy_stop(pdata->phy_dev); + + SMSC_TRACE(IFDOWN, "Interface stopped"); + return 0; +} + +/* Entry point for transmitting a packet */ +static int smsc911x_hard_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + unsigned int freespace; + unsigned int tx_cmd_a; + unsigned int tx_cmd_b; + unsigned int temp; + u32 wrsz; + ulong bufp; + + freespace = smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TDFREE_; + + if (unlikely(freespace < TX_FIFO_LOW_THRESHOLD)) + SMSC_WARNING(TX_ERR, + "Tx data fifo low, space available: %d", freespace); + + /* Word alignment adjustment */ + tx_cmd_a = (u32)((ulong)skb->data & 0x03) << 16; + tx_cmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_; + tx_cmd_a |= (unsigned int)skb->len; + + tx_cmd_b = ((unsigned int)skb->len) << 16; + tx_cmd_b |= (unsigned int)skb->len; + + smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_a); + smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_b); + + bufp = (ulong)skb->data & (~0x3); + wrsz = (u32)skb->len + 3; + wrsz += (u32)((ulong)skb->data & 0x3); + wrsz >>= 2; + + smsc911x_tx_writefifo(pdata, (unsigned int *)bufp, wrsz); + freespace -= (skb->len + 32); + dev_kfree_skb(skb); + dev->trans_start = jiffies; + + if (unlikely(smsc911x_tx_get_txstatcount(pdata) >= 30)) + smsc911x_tx_update_txcounters(dev); + + if (freespace < TX_FIFO_LOW_THRESHOLD) { + netif_stop_queue(dev); + temp = smsc911x_reg_read(pdata, FIFO_INT); + temp &= 0x00FFFFFF; + temp |= 0x32000000; + smsc911x_reg_write(pdata, FIFO_INT, temp); + } + + return NETDEV_TX_OK; +} + +/* Entry point for getting status counters */ +static struct net_device_stats *smsc911x_get_stats(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + smsc911x_tx_update_txcounters(dev); + dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP); + return &dev->stats; +} + +/* Entry point for setting addressing modes */ +static void smsc911x_set_multicast_list(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + unsigned long flags; + + if (dev->flags & IFF_PROMISC) { + /* Enabling promiscuous mode */ + pdata->set_bits_mask = MAC_CR_PRMS_; + pdata->clear_bits_mask = (MAC_CR_MCPAS_ | MAC_CR_HPFILT_); + pdata->hashhi = 0; + pdata->hashlo = 0; + } else if (dev->flags & IFF_ALLMULTI) { + /* Enabling all multicast mode */ + pdata->set_bits_mask = MAC_CR_MCPAS_; + pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_HPFILT_); + pdata->hashhi = 0; + pdata->hashlo = 0; + } else if (dev->mc_count > 0) { + /* Enabling specific multicast addresses */ + unsigned int hash_high = 0; + unsigned int hash_low = 0; + unsigned int count = 0; + struct dev_mc_list *mc_list = dev->mc_list; + + pdata->set_bits_mask = MAC_CR_HPFILT_; + pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_MCPAS_); + + while (mc_list) { + count++; + if ((mc_list->dmi_addrlen) == ETH_ALEN) { + unsigned int bitnum = + smsc911x_hash(mc_list->dmi_addr); + unsigned int mask = 0x01 << (bitnum & 0x1F); + if (bitnum & 0x20) + hash_high |= mask; + else + hash_low |= mask; + } else { + SMSC_WARNING(DRV, "dmi_addrlen != 6"); + } + mc_list = mc_list->next; + } + if (count != (unsigned int)dev->mc_count) + SMSC_WARNING(DRV, "mc_count != dev->mc_count"); + + pdata->hashhi = hash_high; + pdata->hashlo = hash_low; + } else { + /* Enabling local MAC address only */ + pdata->set_bits_mask = 0; + pdata->clear_bits_mask = + (MAC_CR_PRMS_ | MAC_CR_MCPAS_ | MAC_CR_HPFILT_); + pdata->hashhi = 0; + pdata->hashlo = 0; + } + + spin_lock_irqsave(&pdata->mac_lock, flags); + + if (pdata->generation <= 1) { + /* Older hardware revision - cannot change these flags while + * receiving data */ + if (!pdata->multicast_update_pending) { + unsigned int temp; + SMSC_TRACE(HW, "scheduling mcast update"); + pdata->multicast_update_pending = 1; + + /* Request the hardware to stop, then perform the + * update when we get an RX_STOP interrupt */ + smsc911x_reg_write(pdata, INT_STS, INT_STS_RXSTOP_INT_); + temp = smsc911x_reg_read(pdata, INT_EN); + temp |= INT_EN_RXSTOP_INT_EN_; + smsc911x_reg_write(pdata, INT_EN, temp); + + temp = smsc911x_mac_read(pdata, MAC_CR); + temp &= ~(MAC_CR_RXEN_); + smsc911x_mac_write(pdata, MAC_CR, temp); + } else { + /* There is another update pending, this should now + * use the newer values */ + } + } else { + /* Newer hardware revision - can write immediately */ + smsc911x_rx_multicast_update(pdata); + } + + spin_unlock_irqrestore(&pdata->mac_lock, flags); +} + +static irqreturn_t smsc911x_irqhandler(int irq, void *dev_id) +{ + struct net_device *dev = dev_id; + struct smsc911x_data *pdata = netdev_priv(dev); + u32 intsts = smsc911x_reg_read(pdata, INT_STS); + u32 inten = smsc911x_reg_read(pdata, INT_EN); + int serviced = IRQ_NONE; + u32 temp; + + if (unlikely(intsts & inten & INT_STS_SW_INT_)) { + temp = smsc911x_reg_read(pdata, INT_EN); + temp &= (~INT_EN_SW_INT_EN_); + smsc911x_reg_write(pdata, INT_EN, temp); + smsc911x_reg_write(pdata, INT_STS, INT_STS_SW_INT_); + pdata->software_irq_signal = 1; + smp_wmb(); + serviced = IRQ_HANDLED; + } + + if (unlikely(intsts & inten & INT_STS_RXSTOP_INT_)) { + /* Called when there is a multicast update scheduled and + * it is now safe to complete the update */ + SMSC_TRACE(INTR, "RX Stop interrupt"); + temp = smsc911x_reg_read(pdata, INT_EN); + temp &= (~INT_EN_RXSTOP_INT_EN_); + smsc911x_reg_write(pdata, INT_EN, temp); + smsc911x_reg_write(pdata, INT_STS, INT_STS_RXSTOP_INT_); + smsc911x_rx_multicast_update_workaround(pdata); + serviced = IRQ_HANDLED; + } + + if (intsts & inten & INT_STS_TDFA_) { + temp = smsc911x_reg_read(pdata, FIFO_INT); + temp |= FIFO_INT_TX_AVAIL_LEVEL_; + smsc911x_reg_write(pdata, FIFO_INT, temp); + smsc911x_reg_write(pdata, INT_STS, INT_STS_TDFA_); + netif_wake_queue(dev); + serviced = IRQ_HANDLED; + } + + if (unlikely(intsts & inten & INT_STS_RXE_)) { + SMSC_TRACE(INTR, "RX Error interrupt"); + smsc911x_reg_write(pdata, INT_STS, INT_STS_RXE_); + serviced = IRQ_HANDLED; + } + + if (likely(intsts & inten & INT_STS_RSFL_)) { + if (likely(netif_rx_schedule_prep(dev, &pdata->napi))) { + /* Disable Rx interrupts */ + temp = smsc911x_reg_read(pdata, INT_EN); + temp &= (~INT_EN_RSFL_EN_); + smsc911x_reg_write(pdata, INT_EN, temp); + /* Schedule a NAPI poll */ + __netif_rx_schedule(dev, &pdata->napi); + } else { + SMSC_WARNING(RX_ERR, + "netif_rx_schedule_prep failed"); + } + serviced = IRQ_HANDLED; + } + + return serviced; +} + +#ifdef CONFIG_NET_POLL_CONTROLLER +void smsc911x_poll_controller(struct net_device *dev) +{ + disable_irq(dev->irq); + smsc911x_irqhandler(0, dev); + enable_irq(dev->irq); +} +#endif /* CONFIG_NET_POLL_CONTROLLER */ + +/* Standard ioctls for mii-tool */ +static int smsc911x_do_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + + if (!netif_running(dev) || !pdata->phy_dev) + return -EINVAL; + + return phy_mii_ioctl(pdata->phy_dev, if_mii(ifr), cmd); +} + +static int +smsc911x_ethtool_getsettings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + + cmd->maxtxpkt = 1; + cmd->maxrxpkt = 1; + return phy_ethtool_gset(pdata->phy_dev, cmd); +} + +static int +smsc911x_ethtool_setsettings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + + return phy_ethtool_sset(pdata->phy_dev, cmd); +} + +static void smsc911x_ethtool_getdrvinfo(struct net_device *dev, + struct ethtool_drvinfo *info) +{ + strlcpy(info->driver, SMSC_CHIPNAME, sizeof(info->driver)); + strlcpy(info->version, SMSC_DRV_VERSION, sizeof(info->version)); + strlcpy(info->bus_info, dev->dev.parent->bus_id, + sizeof(info->bus_info)); +} + +static int smsc911x_ethtool_nwayreset(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + + return phy_start_aneg(pdata->phy_dev); +} + +static u32 smsc911x_ethtool_getmsglevel(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + return pdata->msg_enable; +} + +static void smsc911x_ethtool_setmsglevel(struct net_device *dev, u32 level) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + pdata->msg_enable = level; +} + +static int smsc911x_ethtool_getregslen(struct net_device *dev) +{ + return (((E2P_DATA - ID_REV) / 4 + 1) + (WUCSR - MAC_CR) + 1 + 32) * + sizeof(u32); +} + +static void +smsc911x_ethtool_getregs(struct net_device *dev, struct ethtool_regs *regs, + void *buf) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + struct phy_device *phy_dev = pdata->phy_dev; + unsigned long flags; + unsigned int i; + unsigned int j = 0; + u32 *data = buf; + + regs->version = pdata->idrev; + for (i = ID_REV; i <= E2P_DATA; i += (sizeof(u32))) + data[j++] = smsc911x_reg_read(pdata, i); + + for (i = MAC_CR; i <= WUCSR; i++) { + spin_lock_irqsave(&pdata->mac_lock, flags); + data[j++] = smsc911x_mac_read(pdata, i); + spin_unlock_irqrestore(&pdata->mac_lock, flags); + } + + for (i = 0; i <= 31; i++) + data[j++] = smsc911x_mii_read(phy_dev->bus, phy_dev->addr, i); +} + +static void smsc911x_eeprom_enable_access(struct smsc911x_data *pdata) +{ + unsigned int temp = smsc911x_reg_read(pdata, GPIO_CFG); + temp &= ~GPIO_CFG_EEPR_EN_; + smsc911x_reg_write(pdata, GPIO_CFG, temp); + msleep(1); +} + +static int smsc911x_eeprom_send_cmd(struct smsc911x_data *pdata, u32 op) +{ + int timeout = 100; + u32 e2cmd; + + SMSC_TRACE(DRV, "op 0x%08x", op); + if (smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_) { + SMSC_WARNING(DRV, "Busy at start"); + return -EBUSY; + } + + e2cmd = op | E2P_CMD_EPC_BUSY_; + smsc911x_reg_write(pdata, E2P_CMD, e2cmd); + + do { + msleep(1); + e2cmd = smsc911x_reg_read(pdata, E2P_CMD); + } while ((e2cmd & E2P_CMD_EPC_BUSY_) && (timeout--)); + + if (!timeout) { + SMSC_TRACE(DRV, "TIMED OUT"); + return -EAGAIN; + } + + if (e2cmd & E2P_CMD_EPC_TIMEOUT_) { + SMSC_TRACE(DRV, "Error occured during eeprom operation"); + return -EINVAL; + } + + return 0; +} + +static int smsc911x_eeprom_read_location(struct smsc911x_data *pdata, + u8 address, u8 *data) +{ + u32 op = E2P_CMD_EPC_CMD_READ_ | address; + int ret; + + SMSC_TRACE(DRV, "address 0x%x", address); + ret = smsc911x_eeprom_send_cmd(pdata, op); + + if (!ret) + data[address] = smsc911x_reg_read(pdata, E2P_DATA); + + return ret; +} + +static int smsc911x_eeprom_write_location(struct smsc911x_data *pdata, + u8 address, u8 data) +{ + u32 op = E2P_CMD_EPC_CMD_ERASE_ | address; + int ret; + + SMSC_TRACE(DRV, "address 0x%x, data 0x%x", address, data); + ret = smsc911x_eeprom_send_cmd(pdata, op); + + if (!ret) { + op = E2P_CMD_EPC_CMD_WRITE_ | address; + smsc911x_reg_write(pdata, E2P_DATA, (u32)data); + ret = smsc911x_eeprom_send_cmd(pdata, op); + } + + return ret; +} + +static int smsc911x_ethtool_get_eeprom_len(struct net_device *dev) +{ + return SMSC911X_EEPROM_SIZE; +} + +static int smsc911x_ethtool_get_eeprom(struct net_device *dev, + struct ethtool_eeprom *eeprom, u8 *data) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + u8 eeprom_data[SMSC911X_EEPROM_SIZE]; + int len; + int i; + + smsc911x_eeprom_enable_access(pdata); + + len = min(eeprom->len, SMSC911X_EEPROM_SIZE); + for (i = 0; i < len; i++) { + int ret = smsc911x_eeprom_read_location(pdata, i, eeprom_data); + if (ret < 0) { + eeprom->len = 0; + return ret; + } + } + + memcpy(data, &eeprom_data[eeprom->offset], len); + eeprom->len = len; + return 0; +} + +static int smsc911x_ethtool_set_eeprom(struct net_device *dev, + struct ethtool_eeprom *eeprom, u8 *data) +{ + int ret; + struct smsc911x_data *pdata = netdev_priv(dev); + + smsc911x_eeprom_enable_access(pdata); + smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWEN_); + ret = smsc911x_eeprom_write_location(pdata, eeprom->offset, *data); + smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWDS_); + + /* Single byte write, according to man page */ + eeprom->len = 1; + + return ret; +} + +static struct ethtool_ops smsc911x_ethtool_ops = { + .get_settings = smsc911x_ethtool_getsettings, + .set_settings = smsc911x_ethtool_setsettings, + .get_link = ethtool_op_get_link, + .get_drvinfo = smsc911x_ethtool_getdrvinfo, + .nway_reset = smsc911x_ethtool_nwayreset, + .get_msglevel = smsc911x_ethtool_getmsglevel, + .set_msglevel = smsc911x_ethtool_setmsglevel, + .get_regs_len = smsc911x_ethtool_getregslen, + .get_regs = smsc911x_ethtool_getregs, + .get_eeprom_len = smsc911x_ethtool_get_eeprom_len, + .get_eeprom = smsc911x_ethtool_get_eeprom, + .set_eeprom = smsc911x_ethtool_set_eeprom, +}; + +/* Initializing private device structures, only called from probe */ +static int __devinit smsc911x_init(struct net_device *dev) +{ + struct smsc911x_data *pdata = netdev_priv(dev); + unsigned int byte_test; + + SMSC_TRACE(PROBE, "Driver Parameters:"); + SMSC_TRACE(PROBE, "LAN base: 0x%08lX", + (unsigned long)pdata->ioaddr); + SMSC_TRACE(PROBE, "IRQ: %d", dev->irq); + SMSC_TRACE(PROBE, "PHY will be autodetected."); + +#if (!SMSC_CAN_USE_32BIT) + spin_lock_init(&pdata->dev_lock); +#endif + + if (pdata->ioaddr == 0) { + SMSC_WARNING(PROBE, "pdata->ioaddr: 0x00000000"); + return -ENODEV; + } + + /* Check byte ordering */ + byte_test = smsc911x_reg_read(pdata, BYTE_TEST); + SMSC_TRACE(PROBE, "BYTE_TEST: 0x%08X", byte_test); + if (byte_test == 0x43218765) { + SMSC_TRACE(PROBE, "BYTE_TEST looks swapped, " + "applying WORD_SWAP"); + smsc911x_reg_write(pdata, WORD_SWAP, 0xffffffff); + + /* 1 dummy read of BYTE_TEST is needed after a write to + * WORD_SWAP before its contents are valid */ + byte_test = smsc911x_reg_read(pdata, BYTE_TEST); + + byte_test = smsc911x_reg_read(pdata, BYTE_TEST); + } + + if (byte_test != 0x87654321) { + SMSC_WARNING(DRV, "BYTE_TEST: 0x%08X", byte_test); + if (((byte_test >> 16) & 0xFFFF) == (byte_test & 0xFFFF)) { + SMSC_WARNING(PROBE, + "top 16 bits equal to bottom 16 bits"); + SMSC_TRACE(PROBE, "This may mean the chip is set " + "for 32 bit while the bus is reading 16 bit"); + } + return -ENODEV; + } + + /* Default generation to zero (all workarounds apply) */ + pdata->generation = 0; + + pdata->idrev = smsc911x_reg_read(pdata, ID_REV); + switch (pdata->idrev & 0xFFFF0000) { + case 0x01180000: + case 0x01170000: + case 0x01160000: + case 0x01150000: + /* LAN911[5678] family */ + pdata->generation = pdata->idrev & 0x0000FFFF; + break; + + case 0x118A0000: + case 0x117A0000: + case 0x116A0000: + case 0x115A0000: + /* LAN921[5678] family */ + pdata->generation = 3; + break; + + case 0x92100000: + case 0x92110000: + case 0x92200000: + case 0x92210000: + /* LAN9210/LAN9211/LAN9220/LAN9221 */ + pdata->generation = 4; + break; + + default: + SMSC_WARNING(PROBE, "LAN911x not identified, idrev: 0x%08X", + pdata->idrev); + return -ENODEV; + } + + SMSC_TRACE(PROBE, "LAN911x identified, idrev: 0x%08X, generation: %d", + pdata->idrev, pdata->generation); + + if (pdata->generation == 0) + SMSC_WARNING(PROBE, + "This driver is not intended for this chip revision"); + + /* Reset the LAN911x */ + if (smsc911x_soft_reset(pdata)) + return -ENODEV; + + /* Disable all interrupt sources until we bring the device up */ + smsc911x_reg_write(pdata, INT_EN, 0); + + ether_setup(dev); + dev->open = smsc911x_open; + dev->stop = smsc911x_stop; + dev->hard_start_xmit = smsc911x_hard_start_xmit; + dev->get_stats = smsc911x_get_stats; + dev->set_multicast_list = smsc911x_set_multicast_list; + dev->flags |= IFF_MULTICAST; + dev->do_ioctl = smsc911x_do_ioctl; + netif_napi_add(dev, &pdata->napi, smsc911x_poll, SMSC_NAPI_WEIGHT); + dev->ethtool_ops = &smsc911x_ethtool_ops; + +#ifdef CONFIG_NET_POLL_CONTROLLER + dev->poll_controller = smsc911x_poll_controller; +#endif /* CONFIG_NET_POLL_CONTROLLER */ + + return 0; +} + +static int __devexit smsc911x_drv_remove(struct platform_device *pdev) +{ + struct net_device *dev; + struct smsc911x_data *pdata; + struct resource *res; + + dev = platform_get_drvdata(pdev); + BUG_ON(!dev); + pdata = netdev_priv(dev); + BUG_ON(!pdata); + BUG_ON(!pdata->ioaddr); + BUG_ON(!pdata->phy_dev); + + SMSC_TRACE(IFDOWN, "Stopping driver."); + + phy_disconnect(pdata->phy_dev); + pdata->phy_dev = NULL; + mdiobus_unregister(pdata->mii_bus); + mdiobus_free(pdata->mii_bus); + + platform_set_drvdata(pdev, NULL); + unregister_netdev(dev); + free_irq(dev->irq, dev); + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "smsc911x-memory"); + if (!res) + platform_get_resource(pdev, IORESOURCE_MEM, 0); + + release_mem_region(res->start, res->end - res->start); + + iounmap(pdata->ioaddr); + + free_netdev(dev); + + return 0; +} + +static int __devinit smsc911x_drv_probe(struct platform_device *pdev) +{ + struct net_device *dev; + struct smsc911x_data *pdata; + struct resource *res; + unsigned int intcfg = 0; + int res_size; + int retval; + DECLARE_MAC_BUF(mac); + + pr_info("%s: Driver version %s.\n", SMSC_CHIPNAME, SMSC_DRV_VERSION); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "smsc911x-memory"); + if (!res) + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + pr_warning("%s: Could not allocate resource.\n", + SMSC_CHIPNAME); + retval = -ENODEV; + goto out_0; + } + res_size = res->end - res->start; + + if (!request_mem_region(res->start, res_size, SMSC_CHIPNAME)) { + retval = -EBUSY; + goto out_0; + } + + dev = alloc_etherdev(sizeof(struct smsc911x_data)); + if (!dev) { + pr_warning("%s: Could not allocate device.\n", SMSC_CHIPNAME); + retval = -ENOMEM; + goto out_release_io_1; + } + + SET_NETDEV_DEV(dev, &pdev->dev); + + pdata = netdev_priv(dev); + + dev->irq = platform_get_irq(pdev, 0); + pdata->ioaddr = ioremap_nocache(res->start, res_size); + + /* copy config parameters across if present, otherwise pdata + * defaults to zeros */ + if (pdev->dev.platform_data) { + struct smsc911x_platform_config *config = + pdev->dev.platform_data; + pdata->irq_polarity = config->irq_polarity; + pdata->irq_type = config->irq_type; + pdata->phy_interface = config->phy_interface; + } + + pdata->dev = dev; + pdata->msg_enable = ((1 << debug) - 1); + + if (pdata->ioaddr == NULL) { + SMSC_WARNING(PROBE, + "Error smsc911x base address invalid"); + retval = -ENOMEM; + goto out_free_netdev_2; + } + + retval = smsc911x_init(dev); + if (retval < 0) + goto out_unmap_io_3; + + /* configure irq polarity and type before connecting isr */ + if (pdata->irq_polarity == SMSC911X_IRQ_POLARITY_ACTIVE_HIGH) + intcfg |= INT_CFG_IRQ_POL_; + + if (pdata->irq_type == SMSC911X_IRQ_TYPE_PUSH_PULL) + intcfg |= INT_CFG_IRQ_TYPE_; + + smsc911x_reg_write(pdata, INT_CFG, intcfg); + + /* Ensure interrupts are globally disabled before connecting ISR */ + smsc911x_reg_write(pdata, INT_EN, 0); + smsc911x_reg_write(pdata, INT_STS, 0xFFFFFFFF); + + retval = request_irq(dev->irq, smsc911x_irqhandler, IRQF_DISABLED, + SMSC_CHIPNAME, dev); + if (retval) { + SMSC_WARNING(PROBE, + "Unable to claim requested irq: %d", dev->irq); + goto out_unmap_io_3; + } + + platform_set_drvdata(pdev, dev); + + retval = register_netdev(dev); + if (retval) { + SMSC_WARNING(PROBE, + "Error %i registering device", retval); + goto out_unset_drvdata_4; + } else { + SMSC_TRACE(PROBE, "Network interface: \"%s\"", dev->name); + } + + spin_lock_init(&pdata->mac_lock); + + retval = smsc911x_mii_init(pdev, dev); + if (retval) { + SMSC_WARNING(PROBE, + "Error %i initialising mii", retval); + goto out_unregister_netdev_5; + } + + spin_lock_irq(&pdata->mac_lock); + + /* Check if mac address has been specified when bringing interface up */ + if (is_valid_ether_addr(dev->dev_addr)) { + smsc911x_set_mac_address(pdata, dev->dev_addr); + SMSC_TRACE(PROBE, "MAC Address is specified by configuration"); + } else { + /* Try reading mac address from device. if EEPROM is present + * it will already have been set */ + u32 mac_high16 = smsc911x_mac_read(pdata, ADDRH); + u32 mac_low32 = smsc911x_mac_read(pdata, ADDRL); + dev->dev_addr[0] = (u8)(mac_low32); + dev->dev_addr[1] = (u8)(mac_low32 >> 8); + dev->dev_addr[2] = (u8)(mac_low32 >> 16); + dev->dev_addr[3] = (u8)(mac_low32 >> 24); + dev->dev_addr[4] = (u8)(mac_high16); + dev->dev_addr[5] = (u8)(mac_high16 >> 8); + + if (is_valid_ether_addr(dev->dev_addr)) { + /* eeprom values are valid so use them */ + SMSC_TRACE(PROBE, + "Mac Address is read from LAN911x EEPROM"); + } else { + /* eeprom values are invalid, generate random MAC */ + random_ether_addr(dev->dev_addr); + smsc911x_set_mac_address(pdata, dev->dev_addr); + SMSC_TRACE(PROBE, + "MAC Address is set to random_ether_addr"); + } + } + + spin_unlock_irq(&pdata->mac_lock); + + dev_info(&dev->dev, "MAC Address: %s\n", + print_mac(mac, dev->dev_addr)); + + return 0; + +out_unregister_netdev_5: + unregister_netdev(dev); +out_unset_drvdata_4: + platform_set_drvdata(pdev, NULL); + free_irq(dev->irq, dev); +out_unmap_io_3: + iounmap(pdata->ioaddr); +out_free_netdev_2: + free_netdev(dev); +out_release_io_1: + release_mem_region(res->start, res->end - res->start); +out_0: + return retval; +} + +static struct platform_driver smsc911x_driver = { + .probe = smsc911x_drv_probe, + .remove = smsc911x_drv_remove, + .driver = { + .name = SMSC_CHIPNAME, + }, +}; + +/* Entry point for loading the module */ +static int __init smsc911x_init_module(void) +{ + return platform_driver_register(&smsc911x_driver); +} + +/* entry point for unloading the module */ +static void __exit smsc911x_cleanup_module(void) +{ + platform_driver_unregister(&smsc911x_driver); +} + +module_init(smsc911x_init_module); +module_exit(smsc911x_cleanup_module); diff --git a/drivers/net/smsc911x.h b/drivers/net/smsc911x.h new file mode 100644 index 000000000000..feb36de274ca --- /dev/null +++ b/drivers/net/smsc911x.h @@ -0,0 +1,394 @@ +/*************************************************************************** + * + * Copyright (C) 2004-2008 SMSC + * Copyright (C) 2005-2008 ARM + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * + ***************************************************************************/ +#ifndef __SMSC911X_H__ +#define __SMSC911X_H__ + +#define SMSC_CAN_USE_32BIT 1 +#define TX_FIFO_LOW_THRESHOLD ((u32)1600) +#define SMSC911X_EEPROM_SIZE ((u32)7) +#define USE_DEBUG 0 + +/* This is the maximum number of packets to be received every + * NAPI poll */ +#define SMSC_NAPI_WEIGHT 16 + +/* implements a PHY loopback test at initialisation time, to ensure a packet + * can be succesfully looped back */ +#define USE_PHY_WORK_AROUND + +#define DPRINTK(nlevel, klevel, fmt, args...) \ + ((void)((NETIF_MSG_##nlevel & pdata->msg_enable) && \ + printk(KERN_##klevel "%s: %s: " fmt "\n", \ + pdata->dev->name, __func__, ## args))) + +#if USE_DEBUG >= 1 +#define SMSC_WARNING(nlevel, fmt, args...) \ + DPRINTK(nlevel, WARNING, fmt, ## args) +#else +#define SMSC_WARNING(nlevel, fmt, args...) \ + ({ do {} while (0); 0; }) +#endif + +#if USE_DEBUG >= 2 +#define SMSC_TRACE(nlevel, fmt, args...) \ + DPRINTK(nlevel, INFO, fmt, ## args) +#else +#define SMSC_TRACE(nlevel, fmt, args...) \ + ({ do {} while (0); 0; }) +#endif + +#ifdef CONFIG_DEBUG_SPINLOCK +#define SMSC_ASSERT_MAC_LOCK(pdata) \ + WARN_ON(!spin_is_locked(&pdata->mac_lock)) +#else +#define SMSC_ASSERT_MAC_LOCK(pdata) do {} while (0) +#endif /* CONFIG_DEBUG_SPINLOCK */ + +#define FLOW_CTRL_TX (1) +#define FLOW_CTRL_RX (2) + +/* SMSC911x registers and bitfields */ +#define RX_DATA_FIFO 0x00 + +#define TX_DATA_FIFO 0x20 +#define TX_CMD_A_ON_COMP_ 0x80000000 +#define TX_CMD_A_BUF_END_ALGN_ 0x03000000 +#define TX_CMD_A_4_BYTE_ALGN_ 0x00000000 +#define TX_CMD_A_16_BYTE_ALGN_ 0x01000000 +#define TX_CMD_A_32_BYTE_ALGN_ 0x02000000 +#define TX_CMD_A_DATA_OFFSET_ 0x001F0000 +#define TX_CMD_A_FIRST_SEG_ 0x00002000 +#define TX_CMD_A_LAST_SEG_ 0x00001000 +#define TX_CMD_A_BUF_SIZE_ 0x000007FF +#define TX_CMD_B_PKT_TAG_ 0xFFFF0000 +#define TX_CMD_B_ADD_CRC_DISABLE_ 0x00002000 +#define TX_CMD_B_DISABLE_PADDING_ 0x00001000 +#define TX_CMD_B_PKT_BYTE_LENGTH_ 0x000007FF + +#define RX_STATUS_FIFO 0x40 +#define RX_STS_ES_ 0x00008000 +#define RX_STS_MCAST_ 0x00000400 + +#define RX_STATUS_FIFO_PEEK 0x44 + +#define TX_STATUS_FIFO 0x48 +#define TX_STS_ES_ 0x00008000 + +#define TX_STATUS_FIFO_PEEK 0x4C + +#define ID_REV 0x50 +#define ID_REV_CHIP_ID_ 0xFFFF0000 +#define ID_REV_REV_ID_ 0x0000FFFF + +#define INT_CFG 0x54 +#define INT_CFG_INT_DEAS_ 0xFF000000 +#define INT_CFG_INT_DEAS_CLR_ 0x00004000 +#define INT_CFG_INT_DEAS_STS_ 0x00002000 +#define INT_CFG_IRQ_INT_ 0x00001000 +#define INT_CFG_IRQ_EN_ 0x00000100 +#define INT_CFG_IRQ_POL_ 0x00000010 +#define INT_CFG_IRQ_TYPE_ 0x00000001 + +#define INT_STS 0x58 +#define INT_STS_SW_INT_ 0x80000000 +#define INT_STS_TXSTOP_INT_ 0x02000000 +#define INT_STS_RXSTOP_INT_ 0x01000000 +#define INT_STS_RXDFH_INT_ 0x00800000 +#define INT_STS_RXDF_INT_ 0x00400000 +#define INT_STS_TX_IOC_ 0x00200000 +#define INT_STS_RXD_INT_ 0x00100000 +#define INT_STS_GPT_INT_ 0x00080000 +#define INT_STS_PHY_INT_ 0x00040000 +#define INT_STS_PME_INT_ 0x00020000 +#define INT_STS_TXSO_ 0x00010000 +#define INT_STS_RWT_ 0x00008000 +#define INT_STS_RXE_ 0x00004000 +#define INT_STS_TXE_ 0x00002000 +#define INT_STS_TDFU_ 0x00000800 +#define INT_STS_TDFO_ 0x00000400 +#define INT_STS_TDFA_ 0x00000200 +#define INT_STS_TSFF_ 0x00000100 +#define INT_STS_TSFL_ 0x00000080 +#define INT_STS_RXDF_ 0x00000040 +#define INT_STS_RDFL_ 0x00000020 +#define INT_STS_RSFF_ 0x00000010 +#define INT_STS_RSFL_ 0x00000008 +#define INT_STS_GPIO2_INT_ 0x00000004 +#define INT_STS_GPIO1_INT_ 0x00000002 +#define INT_STS_GPIO0_INT_ 0x00000001 + +#define INT_EN 0x5C +#define INT_EN_SW_INT_EN_ 0x80000000 +#define INT_EN_TXSTOP_INT_EN_ 0x02000000 +#define INT_EN_RXSTOP_INT_EN_ 0x01000000 +#define INT_EN_RXDFH_INT_EN_ 0x00800000 +#define INT_EN_TIOC_INT_EN_ 0x00200000 +#define INT_EN_RXD_INT_EN_ 0x00100000 +#define INT_EN_GPT_INT_EN_ 0x00080000 +#define INT_EN_PHY_INT_EN_ 0x00040000 +#define INT_EN_PME_INT_EN_ 0x00020000 +#define INT_EN_TXSO_EN_ 0x00010000 +#define INT_EN_RWT_EN_ 0x00008000 +#define INT_EN_RXE_EN_ 0x00004000 +#define INT_EN_TXE_EN_ 0x00002000 +#define INT_EN_TDFU_EN_ 0x00000800 +#define INT_EN_TDFO_EN_ 0x00000400 +#define INT_EN_TDFA_EN_ 0x00000200 +#define INT_EN_TSFF_EN_ 0x00000100 +#define INT_EN_TSFL_EN_ 0x00000080 +#define INT_EN_RXDF_EN_ 0x00000040 +#define INT_EN_RDFL_EN_ 0x00000020 +#define INT_EN_RSFF_EN_ 0x00000010 +#define INT_EN_RSFL_EN_ 0x00000008 +#define INT_EN_GPIO2_INT_ 0x00000004 +#define INT_EN_GPIO1_INT_ 0x00000002 +#define INT_EN_GPIO0_INT_ 0x00000001 + +#define BYTE_TEST 0x64 + +#define FIFO_INT 0x68 +#define FIFO_INT_TX_AVAIL_LEVEL_ 0xFF000000 +#define FIFO_INT_TX_STS_LEVEL_ 0x00FF0000 +#define FIFO_INT_RX_AVAIL_LEVEL_ 0x0000FF00 +#define FIFO_INT_RX_STS_LEVEL_ 0x000000FF + +#define RX_CFG 0x6C +#define RX_CFG_RX_END_ALGN_ 0xC0000000 +#define RX_CFG_RX_END_ALGN4_ 0x00000000 +#define RX_CFG_RX_END_ALGN16_ 0x40000000 +#define RX_CFG_RX_END_ALGN32_ 0x80000000 +#define RX_CFG_RX_DMA_CNT_ 0x0FFF0000 +#define RX_CFG_RX_DUMP_ 0x00008000 +#define RX_CFG_RXDOFF_ 0x00001F00 + +#define TX_CFG 0x70 +#define TX_CFG_TXS_DUMP_ 0x00008000 +#define TX_CFG_TXD_DUMP_ 0x00004000 +#define TX_CFG_TXSAO_ 0x00000004 +#define TX_CFG_TX_ON_ 0x00000002 +#define TX_CFG_STOP_TX_ 0x00000001 + +#define HW_CFG 0x74 +#define HW_CFG_TTM_ 0x00200000 +#define HW_CFG_SF_ 0x00100000 +#define HW_CFG_TX_FIF_SZ_ 0x000F0000 +#define HW_CFG_TR_ 0x00003000 +#define HW_CFG_SRST_ 0x00000001 + +/* only available on 115/117 */ +#define HW_CFG_PHY_CLK_SEL_ 0x00000060 +#define HW_CFG_PHY_CLK_SEL_INT_PHY_ 0x00000000 +#define HW_CFG_PHY_CLK_SEL_EXT_PHY_ 0x00000020 +#define HW_CFG_PHY_CLK_SEL_CLK_DIS_ 0x00000040 +#define HW_CFG_SMI_SEL_ 0x00000010 +#define HW_CFG_EXT_PHY_DET_ 0x00000008 +#define HW_CFG_EXT_PHY_EN_ 0x00000004 +#define HW_CFG_SRST_TO_ 0x00000002 + +/* only available on 116/118 */ +#define HW_CFG_32_16_BIT_MODE_ 0x00000004 + +#define RX_DP_CTRL 0x78 +#define RX_DP_CTRL_RX_FFWD_ 0x80000000 + +#define RX_FIFO_INF 0x7C +#define RX_FIFO_INF_RXSUSED_ 0x00FF0000 +#define RX_FIFO_INF_RXDUSED_ 0x0000FFFF + +#define TX_FIFO_INF 0x80 +#define TX_FIFO_INF_TSUSED_ 0x00FF0000 +#define TX_FIFO_INF_TDFREE_ 0x0000FFFF + +#define PMT_CTRL 0x84 +#define PMT_CTRL_PM_MODE_ 0x00003000 +#define PMT_CTRL_PM_MODE_D0_ 0x00000000 +#define PMT_CTRL_PM_MODE_D1_ 0x00001000 +#define PMT_CTRL_PM_MODE_D2_ 0x00002000 +#define PMT_CTRL_PM_MODE_D3_ 0x00003000 +#define PMT_CTRL_PHY_RST_ 0x00000400 +#define PMT_CTRL_WOL_EN_ 0x00000200 +#define PMT_CTRL_ED_EN_ 0x00000100 +#define PMT_CTRL_PME_TYPE_ 0x00000040 +#define PMT_CTRL_WUPS_ 0x00000030 +#define PMT_CTRL_WUPS_NOWAKE_ 0x00000000 +#define PMT_CTRL_WUPS_ED_ 0x00000010 +#define PMT_CTRL_WUPS_WOL_ 0x00000020 +#define PMT_CTRL_WUPS_MULTI_ 0x00000030 +#define PMT_CTRL_PME_IND_ 0x00000008 +#define PMT_CTRL_PME_POL_ 0x00000004 +#define PMT_CTRL_PME_EN_ 0x00000002 +#define PMT_CTRL_READY_ 0x00000001 + +#define GPIO_CFG 0x88 +#define GPIO_CFG_LED3_EN_ 0x40000000 +#define GPIO_CFG_LED2_EN_ 0x20000000 +#define GPIO_CFG_LED1_EN_ 0x10000000 +#define GPIO_CFG_GPIO2_INT_POL_ 0x04000000 +#define GPIO_CFG_GPIO1_INT_POL_ 0x02000000 +#define GPIO_CFG_GPIO0_INT_POL_ 0x01000000 +#define GPIO_CFG_EEPR_EN_ 0x00700000 +#define GPIO_CFG_GPIOBUF2_ 0x00040000 +#define GPIO_CFG_GPIOBUF1_ 0x00020000 +#define GPIO_CFG_GPIOBUF0_ 0x00010000 +#define GPIO_CFG_GPIODIR2_ 0x00000400 +#define GPIO_CFG_GPIODIR1_ 0x00000200 +#define GPIO_CFG_GPIODIR0_ 0x00000100 +#define GPIO_CFG_GPIOD4_ 0x00000020 +#define GPIO_CFG_GPIOD3_ 0x00000010 +#define GPIO_CFG_GPIOD2_ 0x00000004 +#define GPIO_CFG_GPIOD1_ 0x00000002 +#define GPIO_CFG_GPIOD0_ 0x00000001 + +#define GPT_CFG 0x8C +#define GPT_CFG_TIMER_EN_ 0x20000000 +#define GPT_CFG_GPT_LOAD_ 0x0000FFFF + +#define GPT_CNT 0x90 +#define GPT_CNT_GPT_CNT_ 0x0000FFFF + +#define WORD_SWAP 0x98 + +#define FREE_RUN 0x9C + +#define RX_DROP 0xA0 + +#define MAC_CSR_CMD 0xA4 +#define MAC_CSR_CMD_CSR_BUSY_ 0x80000000 +#define MAC_CSR_CMD_R_NOT_W_ 0x40000000 +#define MAC_CSR_CMD_CSR_ADDR_ 0x000000FF + +#define MAC_CSR_DATA 0xA8 + +#define AFC_CFG 0xAC +#define AFC_CFG_AFC_HI_ 0x00FF0000 +#define AFC_CFG_AFC_LO_ 0x0000FF00 +#define AFC_CFG_BACK_DUR_ 0x000000F0 +#define AFC_CFG_FCMULT_ 0x00000008 +#define AFC_CFG_FCBRD_ 0x00000004 +#define AFC_CFG_FCADD_ 0x00000002 +#define AFC_CFG_FCANY_ 0x00000001 + +#define E2P_CMD 0xB0 +#define E2P_CMD_EPC_BUSY_ 0x80000000 +#define E2P_CMD_EPC_CMD_ 0x70000000 +#define E2P_CMD_EPC_CMD_READ_ 0x00000000 +#define E2P_CMD_EPC_CMD_EWDS_ 0x10000000 +#define E2P_CMD_EPC_CMD_EWEN_ 0x20000000 +#define E2P_CMD_EPC_CMD_WRITE_ 0x30000000 +#define E2P_CMD_EPC_CMD_WRAL_ 0x40000000 +#define E2P_CMD_EPC_CMD_ERASE_ 0x50000000 +#define E2P_CMD_EPC_CMD_ERAL_ 0x60000000 +#define E2P_CMD_EPC_CMD_RELOAD_ 0x70000000 +#define E2P_CMD_EPC_TIMEOUT_ 0x00000200 +#define E2P_CMD_MAC_ADDR_LOADED_ 0x00000100 +#define E2P_CMD_EPC_ADDR_ 0x000000FF + +#define E2P_DATA 0xB4 +#define E2P_DATA_EEPROM_DATA_ 0x000000FF +#define LAN_REGISTER_EXTENT 0x00000100 + +/* + * MAC Control and Status Register (Indirect Address) + * Offset (through the MAC_CSR CMD and DATA port) + */ +#define MAC_CR 0x01 +#define MAC_CR_RXALL_ 0x80000000 +#define MAC_CR_HBDIS_ 0x10000000 +#define MAC_CR_RCVOWN_ 0x00800000 +#define MAC_CR_LOOPBK_ 0x00200000 +#define MAC_CR_FDPX_ 0x00100000 +#define MAC_CR_MCPAS_ 0x00080000 +#define MAC_CR_PRMS_ 0x00040000 +#define MAC_CR_INVFILT_ 0x00020000 +#define MAC_CR_PASSBAD_ 0x00010000 +#define MAC_CR_HFILT_ 0x00008000 +#define MAC_CR_HPFILT_ 0x00002000 +#define MAC_CR_LCOLL_ 0x00001000 +#define MAC_CR_BCAST_ 0x00000800 +#define MAC_CR_DISRTY_ 0x00000400 +#define MAC_CR_PADSTR_ 0x00000100 +#define MAC_CR_BOLMT_MASK_ 0x000000C0 +#define MAC_CR_DFCHK_ 0x00000020 +#define MAC_CR_TXEN_ 0x00000008 +#define MAC_CR_RXEN_ 0x00000004 + +#define ADDRH 0x02 + +#define ADDRL 0x03 + +#define HASHH 0x04 + +#define HASHL 0x05 + +#define MII_ACC 0x06 +#define MII_ACC_PHY_ADDR_ 0x0000F800 +#define MII_ACC_MIIRINDA_ 0x000007C0 +#define MII_ACC_MII_WRITE_ 0x00000002 +#define MII_ACC_MII_BUSY_ 0x00000001 + +#define MII_DATA 0x07 + +#define FLOW 0x08 +#define FLOW_FCPT_ 0xFFFF0000 +#define FLOW_FCPASS_ 0x00000004 +#define FLOW_FCEN_ 0x00000002 +#define FLOW_FCBSY_ 0x00000001 + +#define VLAN1 0x09 + +#define VLAN2 0x0A + +#define WUFF 0x0B + +#define WUCSR 0x0C +#define WUCSR_GUE_ 0x00000200 +#define WUCSR_WUFR_ 0x00000040 +#define WUCSR_MPR_ 0x00000020 +#define WUCSR_WAKE_EN_ 0x00000004 +#define WUCSR_MPEN_ 0x00000002 + +/* + * Phy definitions (vendor-specific) + */ +#define LAN9118_PHY_ID 0x00C0001C + +#define MII_INTSTS 0x1D + +#define MII_INTMSK 0x1E +#define PHY_INTMSK_AN_RCV_ (1 << 1) +#define PHY_INTMSK_PDFAULT_ (1 << 2) +#define PHY_INTMSK_AN_ACK_ (1 << 3) +#define PHY_INTMSK_LNKDOWN_ (1 << 4) +#define PHY_INTMSK_RFAULT_ (1 << 5) +#define PHY_INTMSK_AN_COMP_ (1 << 6) +#define PHY_INTMSK_ENERGYON_ (1 << 7) +#define PHY_INTMSK_DEFAULT_ (PHY_INTMSK_ENERGYON_ | \ + PHY_INTMSK_AN_COMP_ | \ + PHY_INTMSK_RFAULT_ | \ + PHY_INTMSK_LNKDOWN_) + +#define ADVERTISE_PAUSE_ALL (ADVERTISE_PAUSE_CAP | \ + ADVERTISE_PAUSE_ASYM) + +#define LPA_PAUSE_ALL (LPA_PAUSE_CAP | \ + LPA_PAUSE_ASYM) + +#endif /* __SMSC911X_H__ */ diff --git a/include/linux/smsc911x.h b/include/linux/smsc911x.h new file mode 100644 index 000000000000..47c4ffd10dbb --- /dev/null +++ b/include/linux/smsc911x.h @@ -0,0 +1,42 @@ +/*************************************************************************** + * + * Copyright (C) 2004-2008 SMSC + * Copyright (C) 2005-2008 ARM + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * + ***************************************************************************/ +#ifndef __LINUX_SMSC911X_H__ +#define __LINUX_SMSC911X_H__ + +#include <linux/phy.h> + +/* platform_device configuration data, should be assigned to + * the platform_device's dev.platform_data */ +struct smsc911x_platform_config { + unsigned int irq_polarity; + unsigned int irq_type; + phy_interface_t phy_interface; +}; + +/* Constants for platform_device irq polarity configuration */ +#define SMSC911X_IRQ_POLARITY_ACTIVE_LOW 0 +#define SMSC911X_IRQ_POLARITY_ACTIVE_HIGH 1 + +/* Constants for platform_device irq type configuration */ +#define SMSC911X_IRQ_TYPE_OPEN_DRAIN 0 +#define SMSC911X_IRQ_TYPE_PUSH_PULL 1 + +#endif /* __LINUX_SMSC911X_H__ */ diff --git a/include/net/ndisc.h b/include/net/ndisc.h index 11dd0137c6a5..ce532f2222ce 100644 --- a/include/net/ndisc.h +++ b/include/net/ndisc.h @@ -108,6 +108,20 @@ extern void ndisc_send_redirect(struct sk_buff *skb, extern int ndisc_mc_map(struct in6_addr *addr, char *buf, struct net_device *dev, int dir); +extern struct sk_buff *ndisc_build_skb(struct net_device *dev, + const struct in6_addr *daddr, + const struct in6_addr *saddr, + struct icmp6hdr *icmp6h, + const struct in6_addr *target, + int llinfo); + +extern void ndisc_send_skb(struct sk_buff *skb, + struct net_device *dev, + struct neighbour *neigh, + const struct in6_addr *daddr, + const struct in6_addr *saddr, + struct icmp6hdr *icmp6h); + /* diff --git a/net/ipv6/ndisc.c b/net/ipv6/ndisc.c index 2a6752dae09d..fbf451c0d77a 100644 --- a/net/ipv6/ndisc.c +++ b/net/ipv6/ndisc.c @@ -437,38 +437,20 @@ static void pndisc_destructor(struct pneigh_entry *n) ipv6_dev_mc_dec(dev, &maddr); } -/* - * Send a Neighbour Advertisement - */ -static void __ndisc_send(struct net_device *dev, - struct neighbour *neigh, - const struct in6_addr *daddr, - const struct in6_addr *saddr, - struct icmp6hdr *icmp6h, const struct in6_addr *target, - int llinfo) +struct sk_buff *ndisc_build_skb(struct net_device *dev, + const struct in6_addr *daddr, + const struct in6_addr *saddr, + struct icmp6hdr *icmp6h, + const struct in6_addr *target, + int llinfo) { - struct flowi fl; - struct dst_entry *dst; struct net *net = dev_net(dev); struct sock *sk = net->ipv6.ndisc_sk; struct sk_buff *skb; struct icmp6hdr *hdr; - struct inet6_dev *idev; int len; int err; - u8 *opt, type; - - type = icmp6h->icmp6_type; - - icmpv6_flow_init(sk, &fl, type, saddr, daddr, dev->ifindex); - - dst = icmp6_dst_alloc(dev, neigh, daddr); - if (!dst) - return; - - err = xfrm_lookup(&dst, &fl, NULL, 0); - if (err < 0) - return; + u8 *opt; if (!dev->addr_len) llinfo = 0; @@ -485,8 +467,7 @@ static void __ndisc_send(struct net_device *dev, ND_PRINTK0(KERN_ERR "ICMPv6 ND: %s() failed to allocate an skb.\n", __func__); - dst_release(dst); - return; + return NULL; } skb_reserve(skb, LL_RESERVED_SPACE(dev)); @@ -513,6 +494,42 @@ static void __ndisc_send(struct net_device *dev, csum_partial((__u8 *) hdr, len, 0)); + return skb; +} + +EXPORT_SYMBOL(ndisc_build_skb); + +void ndisc_send_skb(struct sk_buff *skb, + struct net_device *dev, + struct neighbour *neigh, + const struct in6_addr *daddr, + const struct in6_addr *saddr, + struct icmp6hdr *icmp6h) +{ + struct flowi fl; + struct dst_entry *dst; + struct net *net = dev_net(dev); + struct sock *sk = net->ipv6.ndisc_sk; + struct inet6_dev *idev; + int err; + u8 type; + + type = icmp6h->icmp6_type; + + icmpv6_flow_init(sk, &fl, type, saddr, daddr, dev->ifindex); + + dst = icmp6_dst_alloc(dev, neigh, daddr); + if (!dst) { + kfree_skb(skb); + return; + } + + err = xfrm_lookup(&dst, &fl, NULL, 0); + if (err < 0) { + kfree_skb(skb); + return; + } + skb->dst = dst; idev = in6_dev_get(dst->dev); @@ -529,6 +546,27 @@ static void __ndisc_send(struct net_device *dev, in6_dev_put(idev); } +EXPORT_SYMBOL(ndisc_send_skb); + +/* + * Send a Neighbour Discover packet + */ +static void __ndisc_send(struct net_device *dev, + struct neighbour *neigh, + const struct in6_addr *daddr, + const struct in6_addr *saddr, + struct icmp6hdr *icmp6h, const struct in6_addr *target, + int llinfo) +{ + struct sk_buff *skb; + + skb = ndisc_build_skb(dev, daddr, saddr, icmp6h, target, llinfo); + if (!skb) + return; + + ndisc_send_skb(skb, dev, neigh, daddr, saddr, icmp6h); +} + static void ndisc_send_na(struct net_device *dev, struct neighbour *neigh, const struct in6_addr *daddr, const struct in6_addr *solicited_addr, |