diff options
34 files changed, 887 insertions, 2604 deletions
diff --git a/Documentation/admin-guide/devices.txt b/Documentation/admin-guide/devices.txt index 1649117e6087..e56e00655153 100644 --- a/Documentation/admin-guide/devices.txt +++ b/Documentation/admin-guide/devices.txt @@ -2693,8 +2693,8 @@ 41 = /dev/ttySMX0 Motorola i.MX - port 0 42 = /dev/ttySMX1 Motorola i.MX - port 1 43 = /dev/ttySMX2 Motorola i.MX - port 2 - 44 = /dev/ttyMM0 Marvell MPSC - port 0 - 45 = /dev/ttyMM1 Marvell MPSC - port 1 + 44 = /dev/ttyMM0 Marvell MPSC - port 0 (obsolete unused) + 45 = /dev/ttyMM1 Marvell MPSC - port 1 (obsolete unused) 46 = /dev/ttyCPM0 PPC CPM (SCC or SMC) - port 0 ... 47 = /dev/ttyCPM5 PPC CPM (SCC or SMC) - port 5 diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index 3cba12f855b7..20d351f268ef 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -53,6 +53,9 @@ Optional properties: programmable TX FIFO thresholds. - resets : phandle + reset specifier pairs - overrun-throttle-ms : how long to pause uart rx when input overrun is encountered. +- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD + line respectively. It will use specified GPIO instead of the peripheral + function pin for the UART feature. If unsure, don't specify this property. Note: * fsl,ns16550: @@ -74,3 +77,19 @@ Example: interrupts = <10>; reg-shift = <2>; }; + +Example for OMAP UART using GPIO-based modem control signals: + + uart4: serial@49042000 { + compatible = "ti,omap3-uart"; + reg = <0x49042000 0x400>; + interrupts = <80>; + ti,hwmods = "uart4"; + clock-frequency = <48000000>; + cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; + dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; diff --git a/arch/ia64/hp/sim/simserial.c b/arch/ia64/hp/sim/simserial.c index 7aeb48a18576..1a338e541334 100644 --- a/arch/ia64/hp/sim/simserial.c +++ b/arch/ia64/hp/sim/simserial.c @@ -324,8 +324,6 @@ static int rs_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg) return -ENOIOCTLCMD; } -#define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK)) - /* * This routine will shutdown a serial port; interrupts are disabled, and * DTR is dropped if the hangup on close termio flag is on. diff --git a/drivers/ipack/devices/ipoctal.h b/drivers/ipack/devices/ipoctal.h index 920537883238..75f83ba774a4 100644 --- a/drivers/ipack/devices/ipoctal.h +++ b/drivers/ipack/devices/ipoctal.h @@ -15,7 +15,6 @@ #define NR_CHANNELS 8 #define IPOCTAL_MAX_BOARDS 16 #define MAX_DEVICES (NR_CHANNELS * IPOCTAL_MAX_BOARDS) -#define RELEVANT_IFLAG(iflag) ((iflag) & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK)) /** * struct ipoctal_stats -- Stats since last reset diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h index ebfb0bd5bef5..33ad9d6de532 100644 --- a/drivers/tty/serial/8250/8250.h +++ b/drivers/tty/serial/8250/8250.h @@ -11,6 +11,8 @@ #include <linux/serial_reg.h> #include <linux/dmaengine.h> +#include "../serial_mctrl_gpio.h" + struct uart_8250_dma { int (*tx_dma)(struct uart_8250_port *p); int (*rx_dma)(struct uart_8250_port *p); @@ -128,6 +130,24 @@ static inline void serial_dl_write(struct uart_8250_port *up, int value) up->dl_write(up, value); } +static inline bool serial8250_set_THRI(struct uart_8250_port *up) +{ + if (up->ier & UART_IER_THRI) + return false; + up->ier |= UART_IER_THRI; + serial_out(up, UART_IER, up->ier); + return true; +} + +static inline bool serial8250_clear_THRI(struct uart_8250_port *up) +{ + if (!(up->ier & UART_IER_THRI)) + return false; + up->ier &= ~UART_IER_THRI; + serial_out(up, UART_IER, up->ier); + return true; +} + struct uart_8250_port *serial8250_get_port(int line); void serial8250_rpm_get(struct uart_8250_port *p); @@ -139,14 +159,82 @@ void serial8250_rpm_put_tx(struct uart_8250_port *p); int serial8250_em485_init(struct uart_8250_port *p); void serial8250_em485_destroy(struct uart_8250_port *p); +/* MCR <-> TIOCM conversion */ +static inline int serial8250_TIOCM_to_MCR(int tiocm) +{ + int mcr = 0; + + if (tiocm & TIOCM_RTS) + mcr |= UART_MCR_RTS; + if (tiocm & TIOCM_DTR) + mcr |= UART_MCR_DTR; + if (tiocm & TIOCM_OUT1) + mcr |= UART_MCR_OUT1; + if (tiocm & TIOCM_OUT2) + mcr |= UART_MCR_OUT2; + if (tiocm & TIOCM_LOOP) + mcr |= UART_MCR_LOOP; + + return mcr; +} + +static inline int serial8250_MCR_to_TIOCM(int mcr) +{ + int tiocm = 0; + + if (mcr & UART_MCR_RTS) + tiocm |= TIOCM_RTS; + if (mcr & UART_MCR_DTR) + tiocm |= TIOCM_DTR; + if (mcr & UART_MCR_OUT1) + tiocm |= TIOCM_OUT1; + if (mcr & UART_MCR_OUT2) + tiocm |= TIOCM_OUT2; + if (mcr & UART_MCR_LOOP) + tiocm |= TIOCM_LOOP; + + return tiocm; +} + +/* MSR <-> TIOCM conversion */ +static inline int serial8250_MSR_to_TIOCM(int msr) +{ + int tiocm = 0; + + if (msr & UART_MSR_DCD) + tiocm |= TIOCM_CAR; + if (msr & UART_MSR_RI) + tiocm |= TIOCM_RNG; + if (msr & UART_MSR_DSR) + tiocm |= TIOCM_DSR; + if (msr & UART_MSR_CTS) + tiocm |= TIOCM_CTS; + + return tiocm; +} + static inline void serial8250_out_MCR(struct uart_8250_port *up, int value) { serial_out(up, UART_MCR, value); + + if (up->gpios) + mctrl_gpio_set(up->gpios, serial8250_MCR_to_TIOCM(value)); } static inline int serial8250_in_MCR(struct uart_8250_port *up) { - return serial_in(up, UART_MCR); + int mctrl; + + mctrl = serial_in(up, UART_MCR); + + if (up->gpios) { + unsigned int mctrl_gpio = 0; + + mctrl_gpio = mctrl_gpio_get_outputs(up->gpios, &mctrl_gpio); + mctrl |= serial8250_TIOCM_to_MCR(mctrl_gpio); + } + + return mctrl; } #if defined(__alpha__) && !defined(CONFIG_PCI) diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c index e441221e04b9..df3bcc0b2d74 100644 --- a/drivers/tty/serial/8250/8250_core.c +++ b/drivers/tty/serial/8250/8250_core.c @@ -14,6 +14,7 @@ * serial8250_register_8250_port() ports */ +#include <linux/acpi.h> #include <linux/module.h> #include <linux/moduleparam.h> #include <linux/ioport.h> @@ -982,6 +983,8 @@ int serial8250_register_8250_port(struct uart_8250_port *up) uart = serial8250_find_match_or_unused(&up->port); if (uart && uart->port.type != PORT_8250_CIR) { + struct mctrl_gpios *gpios; + if (uart->port.dev) uart_remove_one_port(&serial8250_reg, &uart->port); @@ -1016,6 +1019,22 @@ int serial8250_register_8250_port(struct uart_8250_port *up) if (up->port.flags & UPF_FIXED_TYPE) uart->port.type = up->port.type; + /* + * Only call mctrl_gpio_init(), if the device has no ACPI + * companion device + */ + if (!has_acpi_companion(uart->port.dev)) { + gpios = mctrl_gpio_init(&uart->port, 0); + if (IS_ERR(gpios)) { + if (PTR_ERR(gpios) != -ENOSYS) { + ret = PTR_ERR(gpios); + goto out_unlock; + } + } else { + uart->gpios = gpios; + } + } + serial8250_set_defaults(uart); /* Possibly override default I/O functions. */ @@ -1082,6 +1101,7 @@ int serial8250_register_8250_port(struct uart_8250_port *up) } } +out_unlock: mutex_unlock(&serial_mutex); return ret; diff --git a/drivers/tty/serial/8250/8250_dma.c b/drivers/tty/serial/8250/8250_dma.c index bfa1a857f3ff..890fa7ddaa7f 100644 --- a/drivers/tty/serial/8250/8250_dma.c +++ b/drivers/tty/serial/8250/8250_dma.c @@ -34,10 +34,8 @@ static void __dma_tx_complete(void *param) uart_write_wakeup(&p->port); ret = serial8250_tx_dma(p); - if (ret) { - p->ier |= UART_IER_THRI; - serial_port_out(&p->port, UART_IER, p->ier); - } + if (ret) + serial8250_set_THRI(p); spin_unlock_irqrestore(&p->port.lock, flags); } @@ -100,10 +98,7 @@ int serial8250_tx_dma(struct uart_8250_port *p) dma_async_issue_pending(dma->txchan); if (dma->tx_err) { dma->tx_err = 0; - if (p->ier & UART_IER_THRI) { - p->ier &= ~UART_IER_THRI; - serial_out(p, UART_IER, p->ier); - } + serial8250_clear_THRI(p); } return 0; err: diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c index 417c7c810df9..b411ba4eb5e9 100644 --- a/drivers/tty/serial/8250/8250_mtk.c +++ b/drivers/tty/serial/8250/8250_mtk.c @@ -10,6 +10,7 @@ #include <linux/module.h> #include <linux/of_irq.h> #include <linux/of_platform.h> +#include <linux/pinctrl/consumer.h> #include <linux/platform_device.h> #include <linux/pm_runtime.h> #include <linux/serial_8250.h> @@ -47,7 +48,6 @@ #define MTK_UART_DMA_EN_RX 0x5 #define MTK_UART_ESCAPE_CHAR 0x77 /* Escape char added under sw fc */ -#define MTK_UART_TX_SIZE UART_XMIT_SIZE #define MTK_UART_RX_SIZE 0x8000 #define MTK_UART_TX_TRIGGER 1 #define MTK_UART_RX_TRIGGER MTK_UART_RX_SIZE @@ -70,6 +70,7 @@ struct mtk8250_data { #ifdef CONFIG_SERIAL_8250_DMA enum dma_rx_status rx_status; #endif + int rx_wakeup_irq; }; /* flow control mode */ @@ -89,28 +90,30 @@ static void mtk8250_dma_rx_complete(void *param) struct mtk8250_data *data = up->port.private_data; struct tty_port *tty_port = &up->port.state->port; struct dma_tx_state state; + int copied, total, cnt; unsigned char *ptr; - int copied; - dma_sync_single_for_cpu(dma->rxchan->device->dev, dma->rx_addr, - dma->rx_size, DMA_FROM_DEVICE); + if (data->rx_status == DMA_RX_SHUTDOWN) + return; dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state); + total = dma->rx_size - state.residue; + cnt = total; - if (data->rx_status == DMA_RX_SHUTDOWN) - return; + if ((data->rx_pos + cnt) > dma->rx_size) + cnt = dma->rx_size - data->rx_pos; - if ((data->rx_pos + state.residue) <= dma->rx_size) { - ptr = (unsigned char *)(data->rx_pos + dma->rx_buf); - copied = tty_insert_flip_string(tty_port, ptr, state.residue); - } else { - ptr = (unsigned char *)(data->rx_pos + dma->rx_buf); - copied = tty_insert_flip_string(tty_port, ptr, - dma->rx_size - data->rx_pos); + ptr = (unsigned char *)(data->rx_pos + dma->rx_buf); + copied = tty_insert_flip_string(tty_port, ptr, cnt); + data->rx_pos += cnt; + + if (total > cnt) { ptr = (unsigned char *)(dma->rx_buf); - copied += tty_insert_flip_string(tty_port, ptr, - data->rx_pos + state.residue - dma->rx_size); + cnt = total - cnt; + copied += tty_insert_flip_string(tty_port, ptr, cnt); + data->rx_pos = cnt; } + up->port.icount.rx += copied; tty_flip_buffer_push(tty_port); @@ -121,9 +124,7 @@ static void mtk8250_dma_rx_complete(void *param) static void mtk8250_rx_dma(struct uart_8250_port *up) { struct uart_8250_dma *dma = up->dma; - struct mtk8250_data *data = up->port.private_data; struct dma_async_tx_descriptor *desc; - struct dma_tx_state state; desc = dmaengine_prep_slave_single(dma->rxchan, dma->rx_addr, dma->rx_size, DMA_DEV_TO_MEM, @@ -138,12 +139,6 @@ static void mtk8250_rx_dma(struct uart_8250_port *up) dma->rx_cookie = dmaengine_submit(desc); - dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state); - data->rx_pos = state.residue; - - dma_sync_single_for_device(dma->rxchan->device->dev, dma->rx_addr, - dma->rx_size, DMA_FROM_DEVICE); - dma_async_issue_pending(dma->rxchan); } @@ -156,13 +151,11 @@ static void mtk8250_dma_enable(struct uart_8250_port *up) if (data->rx_status != DMA_RX_START) return; - dma->rxconf.direction = DMA_DEV_TO_MEM; - dma->rxconf.src_addr_width = dma->rx_size / 1024; - dma->rxconf.src_addr = dma->rx_addr; + dma->rxconf.src_port_window_size = dma->rx_size; + dma->rxconf.src_addr = dma->rx_addr; - dma->txconf.direction = DMA_MEM_TO_DEV; - dma->txconf.dst_addr_width = MTK_UART_TX_SIZE / 1024; - dma->txconf.dst_addr = dma->tx_addr; + dma->txconf.dst_port_window_size = UART_XMIT_SIZE; + dma->txconf.dst_addr = dma->tx_addr; serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); @@ -551,6 +544,8 @@ static int mtk8250_probe(struct platform_device *pdev) pm_runtime_set_active(&pdev->dev); pm_runtime_enable(&pdev->dev); + data->rx_wakeup_irq = platform_get_irq(pdev, 1); + return 0; } @@ -572,15 +567,35 @@ static int mtk8250_remove(struct platform_device *pdev) static int __maybe_unused mtk8250_suspend(struct device *dev) { struct mtk8250_data *data = dev_get_drvdata(dev); + int irq = data->rx_wakeup_irq; + int err; serial8250_suspend_port(data->line); + pinctrl_pm_select_sleep_state(dev); + if (irq >= 0) { + err = enable_irq_wake(irq); + if (err) { + dev_err(dev, + "failed to enable irq wake on IRQ %d: %d\n", + irq, err); + pinctrl_pm_select_default_state(dev); + serial8250_resume_port(data->line); + return err; + } + } + return 0; } static int __maybe_unused mtk8250_resume(struct device *dev) { struct mtk8250_data *data = dev_get_drvdata(dev); + int irq = data->rx_wakeup_irq; + + if (irq >= 0) + disable_irq_wake(irq); + pinctrl_pm_select_default_state(dev); serial8250_resume_port(data->line); diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c index 0277479c87e9..0826cfdbd406 100644 --- a/drivers/tty/serial/8250/8250_of.c +++ b/drivers/tty/serial/8250/8250_of.c @@ -70,9 +70,10 @@ static int of_platform_serial_setup(struct platform_device *ofdev, /* Get clk rate through clk driver if present */ info->clk = devm_clk_get(&ofdev->dev, NULL); if (IS_ERR(info->clk)) { - dev_warn(&ofdev->dev, - "clk or clock-frequency not defined\n"); ret = PTR_ERR(info->clk); + if (ret != -EPROBE_DEFER) + dev_warn(&ofdev->dev, + "failed to get clock: %d\n", ret); goto err_pmruntime; } @@ -205,18 +206,16 @@ err_pmruntime: /* * Try to register a serial port */ -static const struct of_device_id of_platform_serial_table[]; static int of_platform_serial_probe(struct platform_device *ofdev) { - const struct of_device_id *match; struct of_serial_info *info; struct uart_8250_port port8250; + unsigned int port_type; u32 tx_threshold; - int port_type; int ret; - match = of_match_device(of_platform_serial_table, &ofdev->dev); - if (!match) + port_type = (unsigned long)of_device_get_match_data(&ofdev->dev); + if (port_type == PORT_UNKNOWN) return -EINVAL; if (of_property_read_bool(ofdev->dev.of_node, "used-by-rtas")) @@ -226,7 +225,6 @@ static int of_platform_serial_probe(struct platform_device *ofdev) if (info == NULL) return -ENOMEM; - port_type = (unsigned long)match->data; memset(&port8250, 0, sizeof(port8250)); ret = of_platform_serial_setup(ofdev, port_type, &port8250.port, info); if (ret) diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c index 0a8316632d75..3ef65cbd2478 100644 --- a/drivers/tty/serial/8250/8250_omap.c +++ b/drivers/tty/serial/8250/8250_omap.c @@ -141,18 +141,20 @@ static void omap8250_set_mctrl(struct uart_port *port, unsigned int mctrl) serial8250_do_set_mctrl(port, mctrl); - /* - * Turn off autoRTS if RTS is lowered and restore autoRTS setting - * if RTS is raised - */ - lcr = serial_in(up, UART_LCR); - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS)) - priv->efr |= UART_EFR_RTS; - else - priv->efr &= ~UART_EFR_RTS; - serial_out(up, UART_EFR, priv->efr); - serial_out(up, UART_LCR, lcr); + if (!up->gpios) { + /* + * Turn off autoRTS if RTS is lowered and restore autoRTS + * setting if RTS is raised + */ + lcr = serial_in(up, UART_LCR); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS)) + priv->efr |= UART_EFR_RTS; + else + priv->efr &= ~UART_EFR_RTS; + serial_out(up, UART_EFR, priv->efr); + serial_out(up, UART_LCR, lcr); + } } /* @@ -453,7 +455,8 @@ static void omap_8250_set_termios(struct uart_port *port, priv->efr = 0; up->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS | UPSTAT_AUTOXOFF); - if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW) { + if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW && + !up->gpios) { /* Enable AUTOCTS (autoRTS is enabled when RTS is raised) */ up->port.status |= UPSTAT_AUTOCTS | UPSTAT_AUTORTS; priv->efr |= UART_EFR_CTS; @@ -923,15 +926,13 @@ static void omap_8250_dma_tx_complete(void *param) ret = omap_8250_tx_dma(p); if (ret) en_thri = true; - } else if (p->capabilities & UART_CAP_RPM) { en_thri = true; } if (en_thri) { dma->tx_err = 1; - p->ier |= UART_IER_THRI; - serial_port_out(&p->port, UART_IER, p->ier); + serial8250_set_THRI(p); } spin_unlock_irqrestore(&p->port.lock, flags); @@ -959,10 +960,7 @@ static int omap_8250_tx_dma(struct uart_8250_port *p) ret = -EBUSY; goto err; } - if (p->ier & UART_IER_THRI) { - p->ier &= ~UART_IER_THRI; - serial_out(p, UART_IER, p->ier); - } + serial8250_clear_THRI(p); return 0; } @@ -1020,10 +1018,7 @@ static int omap_8250_tx_dma(struct uart_8250_port *p) if (dma->tx_err) dma->tx_err = 0; - if (p->ier & UART_IER_THRI) { - p->ier &= ~UART_IER_THRI; - serial_out(p, UART_IER, p->ier); - } + serial8250_clear_THRI(p); if (skip_byte) serial_out(p, UART_TX, xmit->buf[xmit->tail]); return 0; diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index df41397de478..7f740b37700b 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -1326,7 +1326,36 @@ static int pci_default_setup(struct serial_private *priv, return setup_port(priv, port, bar, offset, board->reg_shift); } - +static void +pericom_do_set_divisor(struct uart_port *port, unsigned int baud, + unsigned int quot, unsigned int quot_frac) +{ + int scr; + int lcr; + int actual_baud; + int tolerance; + + for (scr = 5 ; scr <= 15 ; scr++) { + actual_baud = 921600 * 16 / scr; + tolerance = actual_baud / 50; + + if ((baud < actual_baud + tolerance) && + (baud > actual_baud - tolerance)) { + + lcr = serial_port_in(port, UART_LCR); + serial_port_out(port, UART_LCR, lcr | 0x80); + + serial_port_out(port, UART_DLL, 1); + serial_port_out(port, UART_DLM, 0); + serial_port_out(port, 2, 16 - scr); + serial_port_out(port, UART_LCR, lcr); + return; + } else if (baud > actual_baud) { + break; + } + } + serial8250_do_set_divisor(port, baud, quot, quot_frac); +} static int pci_pericom_setup(struct serial_private *priv, const struct pciserial_board *board, struct uart_8250_port *port, int idx) @@ -1339,6 +1368,30 @@ static int pci_pericom_setup(struct serial_private *priv, else offset += idx * board->uart_offset; + + maxnr = (pci_resource_len(priv->dev, bar) - board->first_offset) >> + (board->reg_shift + 3); + + if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr) + return 1; + + port->port.set_divisor = pericom_do_set_divisor; + + return setup_port(priv, port, bar, offset, board->reg_shift); +} + +static int pci_pericom_setup_four_at_eight(struct serial_private *priv, + const struct pciserial_board *board, + struct uart_8250_port *port, int idx) +{ + unsigned int bar, offset = board->first_offset, maxnr; + + bar = FL_GET_BASE(board->flags); + if (board->flags & FL_BASE_BARS) + bar += idx; + else + offset += idx * board->uart_offset; + if (idx==3) offset = 0x38; @@ -1348,6 +1401,8 @@ static int pci_pericom_setup(struct serial_private *priv, if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr) return 1; + port->port.set_divisor = pericom_do_set_divisor; + return setup_port(priv, port, bar, offset, board->reg_shift); } @@ -1995,7 +2050,7 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { .device = PCI_DEVICE_ID_PERICOM_PI7C9X7954, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, /* * PLX @@ -2032,107 +2087,113 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SDB, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_MPCIE_COM_4S, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM232_4DB, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_MPCIE_COM232_4, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SMDB, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_MPCIE_COM_4SM, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM422_4, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM485_4, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S, .device = PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM232_4, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM422_4, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM485_4, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM232_4, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SM, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, { .vendor = PCI_VENDOR_ID_ACCESIO, .device = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4SM, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .setup = pci_pericom_setup, + .setup = pci_pericom_setup_four_at_eight, }, - /* + { + .vendor = PCI_VENDOR_ID_ACCESIO, + .device = PCI_ANY_ID, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_pericom_setup, + }, /* * SBS Technologies, Inc., PMC-OCTALPRO 232 */ { diff --git a/drivers/tty/serial/8250/8250_pnp.c b/drivers/tty/serial/8250/8250_pnp.c index 431e69a5a6a0..dfca33141fcc 100644 --- a/drivers/tty/serial/8250/8250_pnp.c +++ b/drivers/tty/serial/8250/8250_pnp.c @@ -462,8 +462,8 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id) return -ENODEV; dev_dbg(&dev->dev, - "Setup PNP port: port %lx, mem %pa, irq %d, type %d\n", - uart.port.iobase, &uart.port.mapbase, + "Setup PNP port: port %#lx, mem %#llx, irq %u, type %u\n", + uart.port.iobase, (unsigned long long)uart.port.mapbase, uart.port.irq, uart.port.iotype); if (flags & CIR_PORT) { diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c index d2f3310abe54..c1cec808571b 100644 --- a/drivers/tty/serial/8250/8250_port.c +++ b/drivers/tty/serial/8250/8250_port.c @@ -1502,11 +1502,8 @@ static void __stop_tx_rs485(struct uart_8250_port *p) static inline void __do_stop_tx(struct uart_8250_port *p) { - if (p->ier & UART_IER_THRI) { - p->ier &= ~UART_IER_THRI; - serial_out(p, UART_IER, p->ier); + if (serial8250_clear_THRI(p)) serial8250_rpm_put_tx(p); - } } static inline void __stop_tx(struct uart_8250_port *p) @@ -1555,10 +1552,7 @@ static inline void __start_tx(struct uart_port *port) if (up->dma && !up->dma->tx_dma(up)) return; - if (!(up->ier & UART_IER_THRI)) { - up->ier |= UART_IER_THRI; - serial_port_out(port, UART_IER, up->ier); - + if (serial8250_set_THRI(up)) { if (up->bugs & UART_BUG_TXEN) { unsigned char lsr; @@ -1662,6 +1656,8 @@ static void serial8250_disable_ms(struct uart_port *port) if (up->bugs & UART_BUG_NOMSR) return; + mctrl_gpio_disable_ms(up->gpios); + up->ier &= ~UART_IER_MSI; serial_port_out(port, UART_IER, up->ier); } @@ -1674,6 +1670,8 @@ static void serial8250_enable_ms(struct uart_port *port) if (up->bugs & UART_BUG_NOMSR) return; + mctrl_gpio_enable_ms(up->gpios); + up->ier |= UART_IER_MSI; serial8250_rpm_get(up); @@ -1869,13 +1867,13 @@ int serial8250_handle_irq(struct uart_port *port, unsigned int iir) status = serial_port_in(port, UART_LSR); - if (status & (UART_LSR_DR | UART_LSR_BI) && - iir & UART_IIR_RDI) { + if (status & (UART_LSR_DR | UART_LSR_BI)) { if (!up->dma || handle_rx_dma(up, iir)) status = serial8250_rx_chars(up, status); } serial8250_modem_status(up); - if ((!up->dma || up->dma->tx_err) && (status & UART_LSR_THRE)) + if ((!up->dma || up->dma->tx_err) && (status & UART_LSR_THRE) && + (up->ier & UART_IER_THRI)) serial8250_tx_chars(up); uart_unlock_and_check_sysrq(port, flags); @@ -1944,22 +1942,17 @@ unsigned int serial8250_do_get_mctrl(struct uart_port *port) { struct uart_8250_port *up = up_to_u8250p(port); unsigned int status; - unsigned int ret; + unsigned int val; serial8250_rpm_get(up); status = serial8250_modem_status(up); serial8250_rpm_put(up); - ret = 0; - if (status & UART_MSR_DCD) - ret |= TIOCM_CAR; - if (status & UART_MSR_RI) - ret |= TIOCM_RNG; - if (status & UART_MSR_DSR) - ret |= TIOCM_DSR; - if (status & UART_MSR_CTS) - ret |= TIOCM_CTS; - return ret; + val = serial8250_MSR_to_TIOCM(status); + if (up->gpios) + return mctrl_gpio_get(up->gpios, &val); + + return val; } EXPORT_SYMBOL_GPL(serial8250_do_get_mctrl); @@ -1973,18 +1966,9 @@ static unsigned int serial8250_get_mctrl(struct uart_port *port) void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl) { struct uart_8250_port *up = up_to_u8250p(port); - unsigned char mcr = 0; + unsigned char mcr; - if (mctrl & TIOCM_RTS) - mcr |= UART_MCR_RTS; - if (mctrl & TIOCM_DTR) - mcr |= UART_MCR_DTR; - if (mctrl & TIOCM_OUT1) - mcr |= UART_MCR_OUT1; - if (mctrl & TIOCM_OUT2) - mcr |= UART_MCR_OUT2; - if (mctrl & TIOCM_LOOP) - mcr |= UART_MCR_LOOP; + mcr = serial8250_TIOCM_to_MCR(mctrl); mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr; diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig index 296115f6a4d8..509f6a3bb9ff 100644 --- a/drivers/tty/serial/8250/Kconfig +++ b/drivers/tty/serial/8250/Kconfig @@ -8,6 +8,7 @@ config SERIAL_8250 tristate "8250/16550 and compatible serial support" depends on !S390 select SERIAL_CORE + select SERIAL_MCTRL_GPIO if GPIOLIB ---help--- This selects whether you want to include the driver for the standard serial ports. The standard answer is Y. People who might say N diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 0d31251e04cc..b416c7b33f49 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -457,20 +457,6 @@ config SERIAL_21285_CONSOLE your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) -config SERIAL_MPSC - bool "Marvell MPSC serial port support" - depends on MV64X60 - select SERIAL_CORE - help - Say Y here if you want to use the Marvell MPSC serial controller. - -config SERIAL_MPSC_CONSOLE - bool "Support for console on Marvell MPSC serial port" - depends on SERIAL_MPSC - select SERIAL_CORE_CONSOLE - help - Say Y here if you want to support a serial console on a Marvell MPSC. - config SERIAL_PXA bool "PXA serial port support (DEPRECATED)" depends on ARCH_PXA || ARCH_MMP diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile index 79c3d513db7e..7cd7cabfa6c4 100644 --- a/drivers/tty/serial/Makefile +++ b/drivers/tty/serial/Makefile @@ -46,7 +46,6 @@ obj-$(CONFIG_SERIAL_CPM) += cpm_uart/ obj-$(CONFIG_SERIAL_IMX) += imx.o obj-$(CONFIG_SERIAL_MPC52xx) += mpc52xx_uart.o obj-$(CONFIG_SERIAL_ICOM) += icom.o -obj-$(CONFIG_SERIAL_MPSC) += mpsc.o obj-$(CONFIG_SERIAL_MESON) += meson_uart.o obj-$(CONFIG_SERIAL_SB1250_DUART) += sb1250-duart.o obj-$(CONFIG_SERIAL_SCCNXP) += sccnxp.o diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index 89ade213a1a9..5921a33b2a07 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -1717,7 +1717,7 @@ static int pl011_allocate_irq(struct uart_amba_port *uap) { pl011_write(uap->im, uap, REG_IMSC); - return request_irq(uap->port.irq, pl011_int, 0, "uart-pl011", uap); + return request_irq(uap->port.irq, pl011_int, IRQF_SHARED, "uart-pl011", uap); } /* diff --git a/drivers/tty/serial/cpm_uart/cpm_uart_core.c b/drivers/tty/serial/cpm_uart/cpm_uart_core.c index b929c7ae3a27..de6d02f7abe2 100644 --- a/drivers/tty/serial/cpm_uart/cpm_uart_core.c +++ b/drivers/tty/serial/cpm_uart/cpm_uart_core.c @@ -407,7 +407,16 @@ static int cpm_uart_startup(struct uart_port *port) clrbits16(&pinfo->sccp->scc_sccm, UART_SCCM_RX); } cpm_uart_initbd(pinfo); - cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX); + if (IS_SMC(pinfo)) { + out_be32(&pinfo->smcup->smc_rstate, 0); + out_be32(&pinfo->smcup->smc_tstate, 0); + out_be16(&pinfo->smcup->smc_rbptr, + in_be16(&pinfo->smcup->smc_rbase)); + out_be16(&pinfo->smcup->smc_tbptr, + in_be16(&pinfo->smcup->smc_tbase)); + } else { + cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX); + } } /* Install interrupt handler. */ retval = request_irq(port->irq, cpm_uart_int, 0, "cpm_uart", port); @@ -567,8 +576,6 @@ static void cpm_uart_set_termios(struct uart_port *port, /* * Set up parity check flag */ -#define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK)) - port->read_status_mask = (BD_SC_EMPTY | BD_SC_OV); if (termios->c_iflag & INPCK) port->read_status_mask |= BD_SC_FR | BD_SC_PR; @@ -861,16 +868,14 @@ static void cpm_uart_init_smc(struct uart_cpm_port *pinfo) (u8 __iomem *)pinfo->tx_bd_base - DPRAM_BASE); /* - * In case SMC1 is being relocated... + * In case SMC is being relocated... */ -#if defined (CONFIG_I2C_SPI_SMC1_UCODE_PATCH) out_be16(&up->smc_rbptr, in_be16(&pinfo->smcup->smc_rbase)); out_be16(&up->smc_tbptr, in_be16(&pinfo->smcup->smc_tbase)); out_be32(&up->smc_rstate, 0); out_be32(&up->smc_tstate, 0); out_be16(&up->smc_brkcr, 1); /* number of break chars */ out_be16(&up->smc_brkec, 0); -#endif /* Set up the uart parameters in the * parameter ram. @@ -884,8 +889,6 @@ static void cpm_uart_init_smc(struct uart_cpm_port *pinfo) out_be16(&up->smc_brkec, 0); out_be16(&up->smc_brkcr, 1); - cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX); - /* Set UART mode, 8 bit, no parity, one stop. * Enable receive and transmit. */ diff --git a/drivers/tty/serial/digicolor-usart.c b/drivers/tty/serial/digicolor-usart.c index f460cca139e2..13ac36e2da4f 100644 --- a/drivers/tty/serial/digicolor-usart.c +++ b/drivers/tty/serial/digicolor-usart.c @@ -541,7 +541,11 @@ static int __init digicolor_uart_init(void) if (ret) return ret; - return platform_driver_register(&digicolor_uart_platform); + ret = platform_driver_register(&digicolor_uart_platform); + if (ret) + uart_unregister_driver(&digicolor_uart); + + return ret; } module_init(digicolor_uart_init); diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c index ea1c85e3b432..92dad2b4ec36 100644 --- a/drivers/tty/serial/fsl_lpuart.c +++ b/drivers/tty/serial/fsl_lpuart.c @@ -234,9 +234,18 @@ static DEFINE_IDA(fsl_lpuart_ida); +enum lpuart_type { + VF610_LPUART, + LS1021A_LPUART, + IMX7ULP_LPUART, + IMX8QXP_LPUART, +}; + struct lpuart_port { struct uart_port port; - struct clk *clk; + enum lpuart_type devtype; + struct clk *ipg_clk; + struct clk *baud_clk; unsigned int txfifo_size; unsigned int rxfifo_size; @@ -261,19 +270,29 @@ struct lpuart_port { }; struct lpuart_soc_data { - char iotype; - u8 reg_off; + enum lpuart_type devtype; + char iotype; + u8 reg_off; }; static const struct lpuart_soc_data vf_data = { + .devtype = VF610_LPUART, .iotype = UPIO_MEM, }; static const struct lpuart_soc_data ls_data = { + .devtype = LS1021A_LPUART, .iotype = UPIO_MEM32BE, }; -static struct lpuart_soc_data imx_data = { +static struct lpuart_soc_data imx7ulp_data = { + .devtype = IMX7ULP_LPUART, + .iotype = UPIO_MEM32, + .reg_off = IMX_REG_OFF, +}; + +static struct lpuart_soc_data imx8qxp_data = { + .devtype = IMX8QXP_LPUART, .iotype = UPIO_MEM32, .reg_off = IMX_REG_OFF, }; @@ -281,7 +300,8 @@ static struct lpuart_soc_data imx_data = { static const struct of_device_id lpuart_dt_ids[] = { { .compatible = "fsl,vf610-lpuart", .data = &vf_data, }, { .compatible = "fsl,ls1021a-lpuart", .data = &ls_data, }, - { .compatible = "fsl,imx7ulp-lpuart", .data = &imx_data, }, + { .compatible = "fsl,imx7ulp-lpuart", .data = &imx7ulp_data, }, + { .compatible = "fsl,imx8qxp-lpuart", .data = &imx8qxp_data, }, { /* sentinel */ } }; MODULE_DEVICE_TABLE(of, lpuart_dt_ids); @@ -289,6 +309,11 @@ MODULE_DEVICE_TABLE(of, lpuart_dt_ids); /* Forward declare this for the dma callbacks*/ static void lpuart_dma_tx_complete(void *arg); +static inline bool is_imx8qxp_lpuart(struct lpuart_port *sport) +{ + return sport->devtype == IMX8QXP_LPUART; +} + static inline u32 lpuart32_read(struct uart_port *port, u32 off) { switch (port->iotype) { @@ -314,6 +339,39 @@ static inline void lpuart32_write(struct uart_port *port, u32 val, } } +static int __lpuart_enable_clks(struct lpuart_port *sport, bool is_en) +{ + int ret = 0; + + if (is_en) { + ret = clk_prepare_enable(sport->ipg_clk); + if (ret) + return ret; + + ret = clk_prepare_enable(sport->baud_clk); + if (ret) { + clk_disable_unprepare(sport->ipg_clk); + return ret; + } + } else { + clk_disable_unprepare(sport->baud_clk); + clk_disable_unprepare(sport->ipg_clk); + } + + return 0; +} + +static unsigned int lpuart_get_baud_clk_rate(struct lpuart_port *sport) +{ + if (is_imx8qxp_lpuart(sport)) + return clk_get_rate(sport->baud_clk); + + return clk_get_rate(sport->ipg_clk); +} + +#define lpuart_enable_clks(x) __lpuart_enable_clks(x, true) +#define lpuart_disable_clks(x) __lpuart_enable_clks(x, false) + static void lpuart_stop_tx(struct uart_port *port) { unsigned char temp; @@ -1040,10 +1098,8 @@ static inline int lpuart_start_rx_dma(struct lpuart_port *sport) sport->rx_dma_rng_buf_len = 16; ring->buf = kmalloc(sport->rx_dma_rng_buf_len, GFP_ATOMIC); - if (!ring->buf) { - dev_err(sport->port.dev, "Ring buf alloc failed\n"); + if (!ring->buf) return -ENOMEM; - } sg_init_one(&sport->rx_sgl, ring->buf, sport->rx_dma_rng_buf_len); sg_set_buf(&sport->rx_sgl, ring->buf, sport->rx_dma_rng_buf_len); @@ -2071,14 +2127,14 @@ lpuart_console_get_options(struct lpuart_port *sport, int *baud, brfa = readb(sport->port.membase + UARTCR4); brfa &= UARTCR4_BRFA_MASK; - uartclk = clk_get_rate(sport->clk); + uartclk = lpuart_get_baud_clk_rate(sport); /* * baud = mod_clk/(16*(sbr[13]+(brfa)/32) */ baud_raw = uartclk / (16 * (sbr + brfa / 32)); if (*baud != baud_raw) - printk(KERN_INFO "Serial: Console lpuart rounded baud rate" + dev_info(sport->port.dev, "Serial: Console lpuart rounded baud rate" "from %d to %d\n", baud_raw, *baud); } @@ -2114,14 +2170,14 @@ lpuart32_console_get_options(struct lpuart_port *sport, int *baud, bd = lpuart32_read(&sport->port, UARTBAUD); bd &= UARTBAUD_SBR_MASK; sbr = bd; - uartclk = clk_get_rate(sport->clk); + uartclk = lpuart_get_baud_clk_rate(sport); /* * baud = mod_clk/(16*(sbr[13]+(brfa)/32) */ baud_raw = uartclk / (16 * sbr); if (*baud != baud_raw) - printk(KERN_INFO "Serial: Console lpuart rounded baud rate" + dev_info(sport->port.dev, "Serial: Console lpuart rounded baud rate" "from %d to %d\n", baud_raw, *baud); } @@ -2288,6 +2344,7 @@ static int lpuart_probe(struct platform_device *pdev) sport->port.mapbase = res->start; sport->port.dev = &pdev->dev; sport->port.type = PORT_LPUART; + sport->devtype = sdata->devtype; ret = platform_get_irq(pdev, 0); if (ret < 0) { dev_err(&pdev->dev, "cannot obtain irq\n"); @@ -2303,20 +2360,27 @@ static int lpuart_probe(struct platform_device *pdev) sport->port.rs485_config = lpuart_config_rs485; - sport->clk = devm_clk_get(&pdev->dev, "ipg"); - if (IS_ERR(sport->clk)) { - ret = PTR_ERR(sport->clk); - dev_err(&pdev->dev, "failed to get uart clk: %d\n", ret); + sport->ipg_clk = devm_clk_get(&pdev->dev, "ipg"); + if (IS_ERR(sport->ipg_clk)) { + ret = PTR_ERR(sport->ipg_clk); + dev_err(&pdev->dev, "failed to get uart ipg clk: %d\n", ret); return ret; } - ret = clk_prepare_enable(sport->clk); - if (ret) { - dev_err(&pdev->dev, "failed to enable uart clk: %d\n", ret); - return ret; + sport->baud_clk = NULL; + if (is_imx8qxp_lpuart(sport)) { + sport->baud_clk = devm_clk_get(&pdev->dev, "baud"); + if (IS_ERR(sport->baud_clk)) { + ret = PTR_ERR(sport->baud_clk); + dev_err(&pdev->dev, "failed to get uart baud clk: %d\n", ret); + return ret; + } } - sport->port.uartclk = clk_get_rate(sport->clk); + ret = lpuart_enable_clks(sport); + if (ret) + return ret; + sport->port.uartclk = lpuart_get_baud_clk_rate(sport); lpuart_ports[sport->port.line] = sport; @@ -2364,7 +2428,7 @@ static int lpuart_probe(struct platform_device *pdev) failed_attach_port: failed_irq_request: - clk_disable_unprepare(sport->clk); + lpuart_disable_clks(sport); return ret; } @@ -2376,7 +2440,7 @@ static int lpuart_remove(struct platform_device *pdev) ida_simple_remove(&fsl_lpuart_ida, sport->port.line); - clk_disable_unprepare(sport->clk); + lpuart_disable_clks(sport); if (sport->dma_tx_chan) dma_release_channel(sport->dma_tx_chan); @@ -2441,7 +2505,7 @@ static int lpuart_suspend(struct device *dev) } if (sport->port.suspended && !irq_wake) - clk_disable_unprepare(sport->clk); + lpuart_disable_clks(sport); return 0; } @@ -2453,7 +2517,7 @@ static int lpuart_resume(struct device *dev) unsigned long temp; if (sport->port.suspended && !irq_wake) - clk_prepare_enable(sport->clk); + lpuart_enable_clks(sport); if (lpuart_is_32(sport)) { lpuart32_setup_watermark(sport); diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index 8b752e895053..57d6e6ba556e 100644 --- a/drivers/tty/serial/imx.c +++ b/drivers/tty/serial/imx.c @@ -383,6 +383,7 @@ static void imx_uart_ucrs_restore(struct imx_port *sport, } #endif +/* called with port.lock taken and irqs caller dependent */ static void imx_uart_rts_active(struct imx_port *sport, u32 *ucr2) { *ucr2 &= ~(UCR2_CTSC | UCR2_CTS); @@ -391,6 +392,7 @@ static void imx_uart_rts_active(struct imx_port *sport, u32 *ucr2) mctrl_gpio_set(sport->gpios, sport->port.mctrl); } +/* called with port.lock taken and irqs caller dependent */ static void imx_uart_rts_inactive(struct imx_port *sport, u32 *ucr2) { *ucr2 &= ~UCR2_CTSC; @@ -400,6 +402,7 @@ static void imx_uart_rts_inactive(struct imx_port *sport, u32 *ucr2) mctrl_gpio_set(sport->gpios, sport->port.mctrl); } +/* called with port.lock taken and irqs caller dependent */ static void imx_uart_rts_auto(struct imx_port *sport, u32 *ucr2) { *ucr2 |= UCR2_CTSC; @@ -1549,40 +1552,46 @@ imx_uart_set_termios(struct uart_port *port, struct ktermios *termios, old_csize = CS8; } + del_timer_sync(&sport->timer); + + /* + * Ask the core to calculate the divisor for us. + */ + baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 16); + quot = uart_get_divisor(port, baud); + + spin_lock_irqsave(&sport->port.lock, flags); + + /* + * Read current UCR2 and save it for future use, then clear all the bits + * except those we will or may need to preserve. + */ + old_ucr2 = imx_uart_readl(sport, UCR2); + ucr2 = old_ucr2 & (UCR2_TXEN | UCR2_RXEN | UCR2_ATEN | UCR2_CTS); + + ucr2 |= UCR2_SRST | UCR2_IRTS; if ((termios->c_cflag & CSIZE) == CS8) - ucr2 = UCR2_WS | UCR2_SRST | UCR2_IRTS; - else - ucr2 = UCR2_SRST | UCR2_IRTS; - - if (termios->c_cflag & CRTSCTS) { - if (sport->have_rtscts) { - ucr2 &= ~UCR2_IRTS; - - if (port->rs485.flags & SER_RS485_ENABLED) { - /* - * RTS is mandatory for rs485 operation, so keep - * it under manual control and keep transmitter - * disabled. - */ - if (port->rs485.flags & - SER_RS485_RTS_AFTER_SEND) - imx_uart_rts_active(sport, &ucr2); - else - imx_uart_rts_inactive(sport, &ucr2); - } else { - imx_uart_rts_auto(sport, &ucr2); - } - } else { - termios->c_cflag &= ~CRTSCTS; - } - } else if (port->rs485.flags & SER_RS485_ENABLED) { - /* disable transmitter */ + ucr2 |= UCR2_WS; + + if (!sport->have_rtscts) + termios->c_cflag &= ~CRTSCTS; + + if (port->rs485.flags & SER_RS485_ENABLED) { + /* + * RTS is mandatory for rs485 operation, so keep + * it under manual control and keep transmitter + * disabled. + */ if (port->rs485.flags & SER_RS485_RTS_AFTER_SEND) imx_uart_rts_active(sport, &ucr2); else imx_uart_rts_inactive(sport, &ucr2); - } + } else if (termios->c_cflag & CRTSCTS) + imx_uart_rts_auto(sport, &ucr2); + + if (termios->c_cflag & CRTSCTS) + ucr2 &= ~UCR2_IRTS; if (termios->c_cflag & CSTOPB) ucr2 |= UCR2_STPB; @@ -1592,16 +1601,6 @@ imx_uart_set_termios(struct uart_port *port, struct ktermios *termios, ucr2 |= UCR2_PROE; } - del_timer_sync(&sport->timer); - - /* - * Ask the core to calculate the divisor for us. - */ - baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 16); - quot = uart_get_divisor(port, baud); - - spin_lock_irqsave(&sport->port.lock, flags); - sport->port.read_status_mask = 0; if (termios->c_iflag & INPCK) sport->port.read_status_mask |= (URXD_FRMERR | URXD_PRERR); @@ -1639,7 +1638,6 @@ imx_uart_set_termios(struct uart_port *port, struct ktermios *termios, imx_uart_writel(sport, old_ucr1 & ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN), UCR1); - old_ucr2 = imx_uart_readl(sport, UCR2); imx_uart_writel(sport, old_ucr2 & ~UCR2_ATEN, UCR2); while (!(imx_uart_readl(sport, USR2) & USR2_TXDC)) @@ -1647,7 +1645,6 @@ imx_uart_set_termios(struct uart_port *port, struct ktermios *termios, /* then, disable everything */ imx_uart_writel(sport, old_ucr2 & ~(UCR2_TXEN | UCR2_RXEN | UCR2_ATEN), UCR2); - old_ucr2 &= (UCR2_TXEN | UCR2_RXEN | UCR2_ATEN); /* custom-baudrate handling */ div = sport->port.uartclk / (baud * 16); @@ -1685,8 +1682,7 @@ imx_uart_set_termios(struct uart_port *port, struct ktermios *termios, imx_uart_writel(sport, old_ucr1, UCR1); - /* set the parity, stop bits and data size */ - imx_uart_writel(sport, ucr2 | old_ucr2, UCR2); + imx_uart_writel(sport, ucr2, UCR2); if (UART_ENABLE_MS(&sport->port, termios->c_cflag)) imx_uart_enable_ms(&sport->port); @@ -2015,7 +2011,7 @@ imx_uart_console_get_options(struct imx_port *sport, int *baud, } if (*baud != baud_raw) - pr_info("Console IMX rounded baud rate from %d to %d\n", + dev_info(sport->port.dev, "Console IMX rounded baud rate from %d to %d\n", baud_raw, *baud); } } diff --git a/drivers/tty/serial/max310x.c b/drivers/tty/serial/max310x.c index e5aebbf5f302..e6c48a99bd85 100644 --- a/drivers/tty/serial/max310x.c +++ b/drivers/tty/serial/max310x.c @@ -258,12 +258,17 @@ struct max310x_one { struct work_struct tx_work; struct work_struct md_work; struct work_struct rs_work; + + u8 wr_header; + u8 rd_header; + u8 rx_buf[MAX310X_FIFO_SIZE]; }; +#define to_max310x_port(_port) \ + container_of(_port, struct max310x_one, port) struct max310x_port { struct max310x_devtype *devtype; struct regmap *regmap; - struct mutex mutex; struct clk *clk; #ifdef CONFIG_GPIOLIB struct gpio_chip gpio; @@ -496,37 +501,48 @@ static bool max310x_reg_precious(struct device *dev, unsigned int reg) static int max310x_set_baud(struct uart_port *port, int baud) { - unsigned int mode = 0, clk = port->uartclk, div = clk / baud; - - /* Check for minimal value for divider */ - if (div < 16) - div = 16; + unsigned int mode = 0, div = 0, frac = 0, c = 0, F = 0; - if (clk % baud && (div / 16) < 0x8000) { + /* + * Calculate the integer divisor first. Select a proper mode + * in case if the requested baud is too high for the pre-defined + * clocks frequency. + */ + div = port->uartclk / baud; + if (div < 8) { + /* Mode x4 */ + c = 4; + mode = MAX310X_BRGCFG_4XMODE_BIT; + } else if (div < 16) { /* Mode x2 */ + c = 8; mode = MAX310X_BRGCFG_2XMODE_BIT; - clk = port->uartclk * 2; - div = clk / baud; - - if (clk % baud && (div / 16) < 0x8000) { - /* Mode x4 */ - mode = MAX310X_BRGCFG_4XMODE_BIT; - clk = port->uartclk * 4; - div = clk / baud; - } + } else { + c = 16; } - max310x_port_write(port, MAX310X_BRGDIVMSB_REG, (div / 16) >> 8); - max310x_port_write(port, MAX310X_BRGDIVLSB_REG, div / 16); - max310x_port_write(port, MAX310X_BRGCFG_REG, (div % 16) | mode); + /* Calculate the divisor in accordance with the fraction coefficient */ + div /= c; + F = c*baud; - return DIV_ROUND_CLOSEST(clk, div); + /* Calculate the baud rate fraction */ + if (div > 0) + frac = (16*(port->uartclk % F)) / F; + else + div = 1; + + max310x_port_write(port, MAX310X_BRGDIVMSB_REG, div >> 8); + max310x_port_write(port, MAX310X_BRGDIVLSB_REG, div); + max310x_port_write(port, MAX310X_BRGCFG_REG, frac | mode); + + /* Return the actual baud rate we just programmed */ + return (16*port->uartclk) / (c*(16*div + frac)); } static int max310x_update_best_err(unsigned long f, long *besterr) { /* Use baudrate 115200 for calculate error */ - long err = f % (115200 * 16); + long err = f % (460800 * 16); if ((*besterr < 0) || (*besterr > err)) { *besterr = err; @@ -607,11 +623,11 @@ static int max310x_set_ref_clk(struct device *dev, struct max310x_port *s, static void max310x_batch_write(struct uart_port *port, u8 *txbuf, unsigned int len) { - u8 header[] = { (port->iobase + MAX310X_THR_REG) | MAX310X_WRITE_BIT }; + struct max310x_one *one = to_max310x_port(port); struct spi_transfer xfer[] = { { - .tx_buf = &header, - .len = sizeof(header), + .tx_buf = &one->wr_header, + .len = sizeof(one->wr_header), }, { .tx_buf = txbuf, .len = len, @@ -622,11 +638,11 @@ static void max310x_batch_write(struct uart_port *port, u8 *txbuf, unsigned int static void max310x_batch_read(struct uart_port *port, u8 *rxbuf, unsigned int len) { - u8 header[] = { port->iobase + MAX310X_RHR_REG }; + struct max310x_one *one = to_max310x_port(port); struct spi_transfer xfer[] = { { - .tx_buf = &header, - .len = sizeof(header), + .tx_buf = &one->rd_header, + .len = sizeof(one->rd_header), }, { .rx_buf = rxbuf, .len = len, @@ -637,8 +653,8 @@ static void max310x_batch_read(struct uart_port *port, u8 *rxbuf, unsigned int l static void max310x_handle_rx(struct uart_port *port, unsigned int rxlen) { + struct max310x_one *one = to_max310x_port(port); unsigned int sts, ch, flag, i; - u8 buf[MAX310X_FIFO_SIZE]; if (port->read_status_mask == MAX310X_LSR_RXOVR_BIT) { /* We are just reading, happily ignoring any error conditions. @@ -653,7 +669,7 @@ static void max310x_handle_rx(struct uart_port *port, unsigned int rxlen) * */ sts = max310x_port_read(port, MAX310X_LSR_IRQSTS_REG); - max310x_batch_read(port, buf, rxlen); + max310x_batch_read(port, one->rx_buf, rxlen); port->icount.rx += rxlen; flag = TTY_NORMAL; @@ -664,9 +680,16 @@ static void max310x_handle_rx(struct uart_port *port, unsigned int rxlen) port->icount.overrun++; } - for (i = 0; i < rxlen; ++i) { - uart_insert_char(port, sts, MAX310X_LSR_RXOVR_BIT, buf[i], flag); - } + for (i = 0; i < (rxlen - 1); ++i) + uart_insert_char(port, sts, 0, one->rx_buf[i], flag); + + /* + * Handle the overrun case for the last character only, since + * the RxFIFO overflow happens after it is pushed to the FIFO + * tail. + */ + uart_insert_char(port, sts, MAX310X_LSR_RXOVR_BIT, + one->rx_buf[rxlen], flag); } else { if (unlikely(rxlen >= port->fifosize)) { @@ -766,10 +789,9 @@ static void max310x_handle_tx(struct uart_port *port) static void max310x_start_tx(struct uart_port *port) { - struct max310x_one *one = container_of(port, struct max310x_one, port); + struct max310x_one *one = to_max310x_port(port); - if (!work_pending(&one->tx_work)) - schedule_work(&one->tx_work); + schedule_work(&one->tx_work); } static irqreturn_t max310x_port_irq(struct max310x_port *s, int portno) @@ -826,14 +848,11 @@ static irqreturn_t max310x_ist(int irq, void *dev_id) return IRQ_RETVAL(handled); } -static void max310x_wq_proc(struct work_struct *ws) +static void max310x_tx_proc(struct work_struct *ws) { struct max310x_one *one = container_of(ws, struct max310x_one, tx_work); - struct max310x_port *s = dev_get_drvdata(one->port.dev); - mutex_lock(&s->mutex); max310x_handle_tx(&one->port); - mutex_unlock(&s->mutex); } static unsigned int max310x_tx_empty(struct uart_port *port) @@ -863,7 +882,7 @@ static void max310x_md_proc(struct work_struct *ws) static void max310x_set_mctrl(struct uart_port *port, unsigned int mctrl) { - struct max310x_one *one = container_of(port, struct max310x_one, port); + struct max310x_one *one = to_max310x_port(port); schedule_work(&one->md_work); } @@ -962,37 +981,36 @@ static void max310x_set_termios(struct uart_port *port, static void max310x_rs_proc(struct work_struct *ws) { struct max310x_one *one = container_of(ws, struct max310x_one, rs_work); - unsigned int val; + unsigned int delay, mode1 = 0, mode2 = 0; - val = (one->port.rs485.delay_rts_before_send << 4) | + delay = (one->port.rs485.delay_rts_before_send << 4) | one->port.rs485.delay_rts_after_send; - max310x_port_write(&one->port, MAX310X_HDPIXDELAY_REG, val); + max310x_port_write(&one->port, MAX310X_HDPIXDELAY_REG, delay); if (one->port.rs485.flags & SER_RS485_ENABLED) { - max310x_port_update(&one->port, MAX310X_MODE1_REG, - MAX310X_MODE1_TRNSCVCTRL_BIT, - MAX310X_MODE1_TRNSCVCTRL_BIT); - max310x_port_update(&one->port, MAX310X_MODE2_REG, - MAX310X_MODE2_ECHOSUPR_BIT, - MAX310X_MODE2_ECHOSUPR_BIT); - } else { - max310x_port_update(&one->port, MAX310X_MODE1_REG, - MAX310X_MODE1_TRNSCVCTRL_BIT, 0); - max310x_port_update(&one->port, MAX310X_MODE2_REG, - MAX310X_MODE2_ECHOSUPR_BIT, 0); + mode1 = MAX310X_MODE1_TRNSCVCTRL_BIT; + + if (!(one->port.rs485.flags & SER_RS485_RX_DURING_TX)) + mode2 = MAX310X_MODE2_ECHOSUPR_BIT; } + + max310x_port_update(&one->port, MAX310X_MODE1_REG, + MAX310X_MODE1_TRNSCVCTRL_BIT, mode1); + max310x_port_update(&one->port, MAX310X_MODE2_REG, + MAX310X_MODE2_ECHOSUPR_BIT, mode2); } static int max310x_rs485_config(struct uart_port *port, struct serial_rs485 *rs485) { - struct max310x_one *one = container_of(port, struct max310x_one, port); + struct max310x_one *one = to_max310x_port(port); if ((rs485->delay_rts_before_send > 0x0f) || (rs485->delay_rts_after_send > 0x0f)) return -ERANGE; - rs485->flags &= SER_RS485_RTS_ON_SEND | SER_RS485_ENABLED; + rs485->flags &= SER_RS485_RTS_ON_SEND | SER_RS485_RX_DURING_TX | + SER_RS485_ENABLED; memset(rs485->padding, 0, sizeof(rs485->padding)); port->rs485 = *rs485; @@ -1018,6 +1036,22 @@ static int max310x_startup(struct uart_port *port) max310x_port_update(port, MAX310X_MODE2_REG, MAX310X_MODE2_FIFORST_BIT, 0); + /* Configure mode1/mode2 to have rs485/rs232 enabled at startup */ + val = (clamp(port->rs485.delay_rts_before_send, 0U, 15U) << 4) | + clamp(port->rs485.delay_rts_after_send, 0U, 15U); + max310x_port_write(port, MAX310X_HDPIXDELAY_REG, val); + + if (port->rs485.flags & SER_RS485_ENABLED) { + max310x_port_update(port, MAX310X_MODE1_REG, + MAX310X_MODE1_TRNSCVCTRL_BIT, + MAX310X_MODE1_TRNSCVCTRL_BIT); + + if (!(port->rs485.flags & SER_RS485_RX_DURING_TX)) + max310x_port_update(port, MAX310X_MODE2_REG, + MAX310X_MODE2_ECHOSUPR_BIT, + MAX310X_MODE2_ECHOSUPR_BIT); + } + /* Configure flow control levels */ /* Flow control halt level 96, resume level 48 */ max310x_port_write(port, MAX310X_FLOWLVL_REG, @@ -1269,8 +1303,6 @@ static int max310x_probe(struct device *dev, struct max310x_devtype *devtype, uartclk = max310x_set_ref_clk(dev, s, freq, xtal); dev_dbg(dev, "Reference clock set to %i Hz\n", uartclk); - mutex_init(&s->mutex); - for (i = 0; i < devtype->nr; i++) { unsigned int line; @@ -1298,11 +1330,15 @@ static int max310x_probe(struct device *dev, struct max310x_devtype *devtype, /* Clear IRQ status register */ max310x_port_read(&s->p[i].port, MAX310X_IRQSTS_REG); /* Initialize queue for start TX */ - INIT_WORK(&s->p[i].tx_work, max310x_wq_proc); + INIT_WORK(&s->p[i].tx_work, max310x_tx_proc); /* Initialize queue for changing LOOPBACK mode */ INIT_WORK(&s->p[i].md_work, max310x_md_proc); /* Initialize queue for changing RS485 mode */ INIT_WORK(&s->p[i].rs_work, max310x_rs_proc); + /* Initialize SPI-transfer buffers */ + s->p[i].wr_header = (s->p[i].port.iobase + MAX310X_THR_REG) | + MAX310X_WRITE_BIT; + s->p[i].rd_header = (s->p[i].port.iobase + MAX310X_RHR_REG); /* Register port */ ret = uart_add_one_port(&max310x_uart, &s->p[i].port); @@ -1350,8 +1386,6 @@ out_uart: } } - mutex_destroy(&s->mutex); - out_clk: clk_disable_unprepare(s->clk); @@ -1372,7 +1406,6 @@ static int max310x_remove(struct device *dev) s->devtype->power(&s->p[i].port, 0); } - mutex_destroy(&s->mutex); clk_disable_unprepare(s->clk); return 0; diff --git a/drivers/tty/serial/mpsc.c b/drivers/tty/serial/mpsc.c deleted file mode 100644 index 1f60d6fe4ff2..000000000000 --- a/drivers/tty/serial/mpsc.c +++ /dev/null @@ -1,2138 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Generic driver for the MPSC (UART mode) on Marvell parts (e.g., GT64240, - * GT64260, MV64340, MV64360, GT96100, ... ). - * - * Author: Mark A. Greer <mgreer@mvista.com> - * - * Based on an old MPSC driver that was in the linuxppc tree. It appears to - * have been created by Chris Zankel (formerly of MontaVista) but there - * is no proper Copyright so I'm not sure. Apparently, parts were also - * taken from PPCBoot (now U-Boot). Also based on drivers/serial/8250.c - * by Russell King. - * - * 2004 (c) MontaVista, Software, Inc. - */ -/* - * The MPSC interface is much like a typical network controller's interface. - * That is, you set up separate rings of descriptors for transmitting and - * receiving data. There is also a pool of buffers with (one buffer per - * descriptor) that incoming data are dma'd into or outgoing data are dma'd - * out of. - * - * The MPSC requires two other controllers to be able to work. The Baud Rate - * Generator (BRG) provides a clock at programmable frequencies which determines - * the baud rate. The Serial DMA Controller (SDMA) takes incoming data from the - * MPSC and DMA's it into memory or DMA's outgoing data and passes it to the - * MPSC. It is actually the SDMA interrupt that the driver uses to keep the - * transmit and receive "engines" going (i.e., indicate data has been - * transmitted or received). - * - * NOTES: - * - * 1) Some chips have an erratum where several regs cannot be - * read. To work around that, we keep a local copy of those regs in - * 'mpsc_port_info'. - * - * 2) Some chips have an erratum where the ctlr will hang when the SDMA ctlr - * accesses system mem with coherency enabled. For that reason, the driver - * assumes that coherency for that ctlr has been disabled. This means - * that when in a cache coherent system, the driver has to manually manage - * the data cache on the areas that it touches because the dma_* macro are - * basically no-ops. - * - * 3) There is an erratum (on PPC) where you can't use the instruction to do - * a DMA_TO_DEVICE/cache clean so DMA_BIDIRECTIONAL/flushes are used in places - * where a DMA_TO_DEVICE/clean would have [otherwise] sufficed. - * - * 4) AFAICT, hardware flow control isn't supported by the controller --MAG. - */ - - -#if defined(CONFIG_SERIAL_MPSC_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) -#define SUPPORT_SYSRQ -#endif - -#include <linux/tty.h> -#include <linux/tty_flip.h> -#include <linux/ioport.h> -#include <linux/init.h> -#include <linux/console.h> -#include <linux/sysrq.h> -#include <linux/serial.h> -#include <linux/serial_core.h> -#include <linux/delay.h> -#include <linux/device.h> -#include <linux/dma-mapping.h> -#include <linux/mv643xx.h> -#include <linux/platform_device.h> -#include <linux/gfp.h> - -#include <asm/io.h> -#include <asm/irq.h> - -#define MPSC_NUM_CTLRS 2 - -/* - * Descriptors and buffers must be cache line aligned. - * Buffers lengths must be multiple of cache line size. - * Number of Tx & Rx descriptors must be powers of 2. - */ -#define MPSC_RXR_ENTRIES 32 -#define MPSC_RXRE_SIZE dma_get_cache_alignment() -#define MPSC_RXR_SIZE (MPSC_RXR_ENTRIES * MPSC_RXRE_SIZE) -#define MPSC_RXBE_SIZE dma_get_cache_alignment() -#define MPSC_RXB_SIZE (MPSC_RXR_ENTRIES * MPSC_RXBE_SIZE) - -#define MPSC_TXR_ENTRIES 32 -#define MPSC_TXRE_SIZE dma_get_cache_alignment() -#define MPSC_TXR_SIZE (MPSC_TXR_ENTRIES * MPSC_TXRE_SIZE) -#define MPSC_TXBE_SIZE dma_get_cache_alignment() -#define MPSC_TXB_SIZE (MPSC_TXR_ENTRIES * MPSC_TXBE_SIZE) - -#define MPSC_DMA_ALLOC_SIZE (MPSC_RXR_SIZE + MPSC_RXB_SIZE + MPSC_TXR_SIZE \ - + MPSC_TXB_SIZE + dma_get_cache_alignment() /* for alignment */) - -/* Rx and Tx Ring entry descriptors -- assume entry size is <= cacheline size */ -struct mpsc_rx_desc { - u16 bufsize; - u16 bytecnt; - u32 cmdstat; - u32 link; - u32 buf_ptr; -} __attribute((packed)); - -struct mpsc_tx_desc { - u16 bytecnt; - u16 shadow; - u32 cmdstat; - u32 link; - u32 buf_ptr; -} __attribute((packed)); - -/* - * Some regs that have the erratum that you can't read them are are shared - * between the two MPSC controllers. This struct contains those shared regs. - */ -struct mpsc_shared_regs { - phys_addr_t mpsc_routing_base_p; - phys_addr_t sdma_intr_base_p; - - void __iomem *mpsc_routing_base; - void __iomem *sdma_intr_base; - - u32 MPSC_MRR_m; - u32 MPSC_RCRR_m; - u32 MPSC_TCRR_m; - u32 SDMA_INTR_CAUSE_m; - u32 SDMA_INTR_MASK_m; -}; - -/* The main driver data structure */ -struct mpsc_port_info { - struct uart_port port; /* Overlay uart_port structure */ - - /* Internal driver state for this ctlr */ - u8 ready; - u8 rcv_data; - - /* Info passed in from platform */ - u8 mirror_regs; /* Need to mirror regs? */ - u8 cache_mgmt; /* Need manual cache mgmt? */ - u8 brg_can_tune; /* BRG has baud tuning? */ - u32 brg_clk_src; - u16 mpsc_max_idle; - int default_baud; - int default_bits; - int default_parity; - int default_flow; - - /* Physical addresses of various blocks of registers (from platform) */ - phys_addr_t mpsc_base_p; - phys_addr_t sdma_base_p; - phys_addr_t brg_base_p; - - /* Virtual addresses of various blocks of registers (from platform) */ - void __iomem *mpsc_base; - void __iomem *sdma_base; - void __iomem *brg_base; - - /* Descriptor ring and buffer allocations */ - void *dma_region; - dma_addr_t dma_region_p; - - dma_addr_t rxr; /* Rx descriptor ring */ - dma_addr_t rxr_p; /* Phys addr of rxr */ - u8 *rxb; /* Rx Ring I/O buf */ - u8 *rxb_p; /* Phys addr of rxb */ - u32 rxr_posn; /* First desc w/ Rx data */ - - dma_addr_t txr; /* Tx descriptor ring */ - dma_addr_t txr_p; /* Phys addr of txr */ - u8 *txb; /* Tx Ring I/O buf */ - u8 *txb_p; /* Phys addr of txb */ - int txr_head; /* Where new data goes */ - int txr_tail; /* Where sent data comes off */ - spinlock_t tx_lock; /* transmit lock */ - - /* Mirrored values of regs we can't read (if 'mirror_regs' set) */ - u32 MPSC_MPCR_m; - u32 MPSC_CHR_1_m; - u32 MPSC_CHR_2_m; - u32 MPSC_CHR_10_m; - u32 BRG_BCR_m; - struct mpsc_shared_regs *shared_regs; -}; - -/* Hooks to platform-specific code */ -int mpsc_platform_register_driver(void); -void mpsc_platform_unregister_driver(void); - -/* Hooks back in to mpsc common to be called by platform-specific code */ -struct mpsc_port_info *mpsc_device_probe(int index); -struct mpsc_port_info *mpsc_device_remove(int index); - -/* Main MPSC Configuration Register Offsets */ -#define MPSC_MMCRL 0x0000 -#define MPSC_MMCRH 0x0004 -#define MPSC_MPCR 0x0008 -#define MPSC_CHR_1 0x000c -#define MPSC_CHR_2 0x0010 -#define MPSC_CHR_3 0x0014 -#define MPSC_CHR_4 0x0018 -#define MPSC_CHR_5 0x001c -#define MPSC_CHR_6 0x0020 -#define MPSC_CHR_7 0x0024 -#define MPSC_CHR_8 0x0028 -#define MPSC_CHR_9 0x002c -#define MPSC_CHR_10 0x0030 -#define MPSC_CHR_11 0x0034 - -#define MPSC_MPCR_FRZ (1 << 9) -#define MPSC_MPCR_CL_5 0 -#define MPSC_MPCR_CL_6 1 -#define MPSC_MPCR_CL_7 2 -#define MPSC_MPCR_CL_8 3 -#define MPSC_MPCR_SBL_1 0 -#define MPSC_MPCR_SBL_2 1 - -#define MPSC_CHR_2_TEV (1<<1) -#define MPSC_CHR_2_TA (1<<7) -#define MPSC_CHR_2_TTCS (1<<9) -#define MPSC_CHR_2_REV (1<<17) -#define MPSC_CHR_2_RA (1<<23) -#define MPSC_CHR_2_CRD (1<<25) -#define MPSC_CHR_2_EH (1<<31) -#define MPSC_CHR_2_PAR_ODD 0 -#define MPSC_CHR_2_PAR_SPACE 1 -#define MPSC_CHR_2_PAR_EVEN 2 -#define MPSC_CHR_2_PAR_MARK 3 - -/* MPSC Signal Routing */ -#define MPSC_MRR 0x0000 -#define MPSC_RCRR 0x0004 -#define MPSC_TCRR 0x0008 - -/* Serial DMA Controller Interface Registers */ -#define SDMA_SDC 0x0000 -#define SDMA_SDCM 0x0008 -#define SDMA_RX_DESC 0x0800 -#define SDMA_RX_BUF_PTR 0x0808 -#define SDMA_SCRDP 0x0810 -#define SDMA_TX_DESC 0x0c00 -#define SDMA_SCTDP 0x0c10 -#define SDMA_SFTDP 0x0c14 - -#define SDMA_DESC_CMDSTAT_PE (1<<0) -#define SDMA_DESC_CMDSTAT_CDL (1<<1) -#define SDMA_DESC_CMDSTAT_FR (1<<3) -#define SDMA_DESC_CMDSTAT_OR (1<<6) -#define SDMA_DESC_CMDSTAT_BR (1<<9) -#define SDMA_DESC_CMDSTAT_MI (1<<10) -#define SDMA_DESC_CMDSTAT_A (1<<11) -#define SDMA_DESC_CMDSTAT_AM (1<<12) -#define SDMA_DESC_CMDSTAT_CT (1<<13) -#define SDMA_DESC_CMDSTAT_C (1<<14) -#define SDMA_DESC_CMDSTAT_ES (1<<15) -#define SDMA_DESC_CMDSTAT_L (1<<16) -#define SDMA_DESC_CMDSTAT_F (1<<17) -#define SDMA_DESC_CMDSTAT_P (1<<18) -#define SDMA_DESC_CMDSTAT_EI (1<<23) -#define SDMA_DESC_CMDSTAT_O (1<<31) - -#define SDMA_DESC_DFLT (SDMA_DESC_CMDSTAT_O \ - | SDMA_DESC_CMDSTAT_EI) - -#define SDMA_SDC_RFT (1<<0) -#define SDMA_SDC_SFM (1<<1) -#define SDMA_SDC_BLMR (1<<6) -#define SDMA_SDC_BLMT (1<<7) -#define SDMA_SDC_POVR (1<<8) -#define SDMA_SDC_RIFB (1<<9) - -#define SDMA_SDCM_ERD (1<<7) -#define SDMA_SDCM_AR (1<<15) -#define SDMA_SDCM_STD (1<<16) -#define SDMA_SDCM_TXD (1<<23) -#define SDMA_SDCM_AT (1<<31) - -#define SDMA_0_CAUSE_RXBUF (1<<0) -#define SDMA_0_CAUSE_RXERR (1<<1) -#define SDMA_0_CAUSE_TXBUF (1<<2) -#define SDMA_0_CAUSE_TXEND (1<<3) -#define SDMA_1_CAUSE_RXBUF (1<<8) -#define SDMA_1_CAUSE_RXERR (1<<9) -#define SDMA_1_CAUSE_TXBUF (1<<10) -#define SDMA_1_CAUSE_TXEND (1<<11) - -#define SDMA_CAUSE_RX_MASK (SDMA_0_CAUSE_RXBUF | SDMA_0_CAUSE_RXERR \ - | SDMA_1_CAUSE_RXBUF | SDMA_1_CAUSE_RXERR) -#define SDMA_CAUSE_TX_MASK (SDMA_0_CAUSE_TXBUF | SDMA_0_CAUSE_TXEND \ - | SDMA_1_CAUSE_TXBUF | SDMA_1_CAUSE_TXEND) - -/* SDMA Interrupt registers */ -#define SDMA_INTR_CAUSE 0x0000 -#define SDMA_INTR_MASK 0x0080 - -/* Baud Rate Generator Interface Registers */ -#define BRG_BCR 0x0000 -#define BRG_BTR 0x0004 - -/* - * Define how this driver is known to the outside (we've been assigned a - * range on the "Low-density serial ports" major). - */ -#define MPSC_MAJOR 204 -#define MPSC_MINOR_START 44 -#define MPSC_DRIVER_NAME "MPSC" -#define MPSC_DEV_NAME "ttyMM" -#define MPSC_VERSION "1.00" - -static struct mpsc_port_info mpsc_ports[MPSC_NUM_CTLRS]; -static struct mpsc_shared_regs mpsc_shared_regs; -static struct uart_driver mpsc_reg; - -static void mpsc_start_rx(struct mpsc_port_info *pi); -static void mpsc_free_ring_mem(struct mpsc_port_info *pi); -static void mpsc_release_port(struct uart_port *port); -/* - ****************************************************************************** - * - * Baud Rate Generator Routines (BRG) - * - ****************************************************************************** - */ -static void mpsc_brg_init(struct mpsc_port_info *pi, u32 clk_src) -{ - u32 v; - - v = (pi->mirror_regs) ? pi->BRG_BCR_m : readl(pi->brg_base + BRG_BCR); - v = (v & ~(0xf << 18)) | ((clk_src & 0xf) << 18); - - if (pi->brg_can_tune) - v &= ~(1 << 25); - - if (pi->mirror_regs) - pi->BRG_BCR_m = v; - writel(v, pi->brg_base + BRG_BCR); - - writel(readl(pi->brg_base + BRG_BTR) & 0xffff0000, - pi->brg_base + BRG_BTR); -} - -static void mpsc_brg_enable(struct mpsc_port_info *pi) -{ - u32 v; - - v = (pi->mirror_regs) ? pi->BRG_BCR_m : readl(pi->brg_base + BRG_BCR); - v |= (1 << 16); - - if (pi->mirror_regs) - pi->BRG_BCR_m = v; - writel(v, pi->brg_base + BRG_BCR); -} - -static void mpsc_brg_disable(struct mpsc_port_info *pi) -{ - u32 v; - - v = (pi->mirror_regs) ? pi->BRG_BCR_m : readl(pi->brg_base + BRG_BCR); - v &= ~(1 << 16); - - if (pi->mirror_regs) - pi->BRG_BCR_m = v; - writel(v, pi->brg_base + BRG_BCR); -} - -/* - * To set the baud, we adjust the CDV field in the BRG_BCR reg. - * From manual: Baud = clk / ((CDV+1)*2) ==> CDV = (clk / (baud*2)) - 1. - * However, the input clock is divided by 16 in the MPSC b/c of how - * 'MPSC_MMCRH' was set up so we have to divide the 'clk' used in our - * calculation by 16 to account for that. So the real calculation - * that accounts for the way the mpsc is set up is: - * CDV = (clk / (baud*2*16)) - 1 ==> CDV = (clk / (baud << 5)) - 1. - */ -static void mpsc_set_baudrate(struct mpsc_port_info *pi, u32 baud) -{ - u32 cdv = (pi->port.uartclk / (baud << 5)) - 1; - u32 v; - - mpsc_brg_disable(pi); - v = (pi->mirror_regs) ? pi->BRG_BCR_m : readl(pi->brg_base + BRG_BCR); - v = (v & 0xffff0000) | (cdv & 0xffff); - - if (pi->mirror_regs) - pi->BRG_BCR_m = v; - writel(v, pi->brg_base + BRG_BCR); - mpsc_brg_enable(pi); -} - -/* - ****************************************************************************** - * - * Serial DMA Routines (SDMA) - * - ****************************************************************************** - */ - -static void mpsc_sdma_burstsize(struct mpsc_port_info *pi, u32 burst_size) -{ - u32 v; - - pr_debug("mpsc_sdma_burstsize[%d]: burst_size: %d\n", - pi->port.line, burst_size); - - burst_size >>= 3; /* Divide by 8 b/c reg values are 8-byte chunks */ - - if (burst_size < 2) - v = 0x0; /* 1 64-bit word */ - else if (burst_size < 4) - v = 0x1; /* 2 64-bit words */ - else if (burst_size < 8) - v = 0x2; /* 4 64-bit words */ - else - v = 0x3; /* 8 64-bit words */ - - writel((readl(pi->sdma_base + SDMA_SDC) & (0x3 << 12)) | (v << 12), - pi->sdma_base + SDMA_SDC); -} - -static void mpsc_sdma_init(struct mpsc_port_info *pi, u32 burst_size) -{ - pr_debug("mpsc_sdma_init[%d]: burst_size: %d\n", pi->port.line, - burst_size); - - writel((readl(pi->sdma_base + SDMA_SDC) & 0x3ff) | 0x03f, - pi->sdma_base + SDMA_SDC); - mpsc_sdma_burstsize(pi, burst_size); -} - -static u32 mpsc_sdma_intr_mask(struct mpsc_port_info *pi, u32 mask) -{ - u32 old, v; - - pr_debug("mpsc_sdma_intr_mask[%d]: mask: 0x%x\n", pi->port.line, mask); - - old = v = (pi->mirror_regs) ? pi->shared_regs->SDMA_INTR_MASK_m : - readl(pi->shared_regs->sdma_intr_base + SDMA_INTR_MASK); - - mask &= 0xf; - if (pi->port.line) - mask <<= 8; - v &= ~mask; - - if (pi->mirror_regs) - pi->shared_regs->SDMA_INTR_MASK_m = v; - writel(v, pi->shared_regs->sdma_intr_base + SDMA_INTR_MASK); - - if (pi->port.line) - old >>= 8; - return old & 0xf; -} - -static void mpsc_sdma_intr_unmask(struct mpsc_port_info *pi, u32 mask) -{ - u32 v; - - pr_debug("mpsc_sdma_intr_unmask[%d]: mask: 0x%x\n", pi->port.line,mask); - - v = (pi->mirror_regs) ? pi->shared_regs->SDMA_INTR_MASK_m - : readl(pi->shared_regs->sdma_intr_base + SDMA_INTR_MASK); - - mask &= 0xf; - if (pi->port.line) - mask <<= 8; - v |= mask; - - if (pi->mirror_regs) - pi->shared_regs->SDMA_INTR_MASK_m = v; - writel(v, pi->shared_regs->sdma_intr_base + SDMA_INTR_MASK); -} - -static void mpsc_sdma_intr_ack(struct mpsc_port_info *pi) -{ - pr_debug("mpsc_sdma_intr_ack[%d]: Acknowledging IRQ\n", pi->port.line); - - if (pi->mirror_regs) - pi->shared_regs->SDMA_INTR_CAUSE_m = 0; - writeb(0x00, pi->shared_regs->sdma_intr_base + SDMA_INTR_CAUSE - + pi->port.line); -} - -static void mpsc_sdma_set_rx_ring(struct mpsc_port_info *pi, - struct mpsc_rx_desc *rxre_p) -{ - pr_debug("mpsc_sdma_set_rx_ring[%d]: rxre_p: 0x%x\n", - pi->port.line, (u32)rxre_p); - - writel((u32)rxre_p, pi->sdma_base + SDMA_SCRDP); -} - -static void mpsc_sdma_set_tx_ring(struct mpsc_port_info *pi, - struct mpsc_tx_desc *txre_p) -{ - writel((u32)txre_p, pi->sdma_base + SDMA_SFTDP); - writel((u32)txre_p, pi->sdma_base + SDMA_SCTDP); -} - -static void mpsc_sdma_cmd(struct mpsc_port_info *pi, u32 val) -{ - u32 v; - - v = readl(pi->sdma_base + SDMA_SDCM); - if (val) - v |= val; - else - v = 0; - wmb(); - writel(v, pi->sdma_base + SDMA_SDCM); - wmb(); -} - -static uint mpsc_sdma_tx_active(struct mpsc_port_info *pi) -{ - return readl(pi->sdma_base + SDMA_SDCM) & SDMA_SDCM_TXD; -} - -static void mpsc_sdma_start_tx(struct mpsc_port_info *pi) -{ - struct mpsc_tx_desc *txre, *txre_p; - - /* If tx isn't running & there's a desc ready to go, start it */ - if (!mpsc_sdma_tx_active(pi)) { - txre = (struct mpsc_tx_desc *)(pi->txr - + (pi->txr_tail * MPSC_TXRE_SIZE)); - dma_cache_sync(pi->port.dev, (void *)txre, MPSC_TXRE_SIZE, - DMA_FROM_DEVICE); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - invalidate_dcache_range((ulong)txre, - (ulong)txre + MPSC_TXRE_SIZE); -#endif - - if (be32_to_cpu(txre->cmdstat) & SDMA_DESC_CMDSTAT_O) { - txre_p = (struct mpsc_tx_desc *) - (pi->txr_p + (pi->txr_tail * MPSC_TXRE_SIZE)); - - mpsc_sdma_set_tx_ring(pi, txre_p); - mpsc_sdma_cmd(pi, SDMA_SDCM_STD | SDMA_SDCM_TXD); - } - } -} - -static void mpsc_sdma_stop(struct mpsc_port_info *pi) -{ - pr_debug("mpsc_sdma_stop[%d]: Stopping SDMA\n", pi->port.line); - - /* Abort any SDMA transfers */ - mpsc_sdma_cmd(pi, 0); - mpsc_sdma_cmd(pi, SDMA_SDCM_AR | SDMA_SDCM_AT); - - /* Clear the SDMA current and first TX and RX pointers */ - mpsc_sdma_set_tx_ring(pi, NULL); - mpsc_sdma_set_rx_ring(pi, NULL); - - /* Disable interrupts */ - mpsc_sdma_intr_mask(pi, 0xf); - mpsc_sdma_intr_ack(pi); -} - -/* - ****************************************************************************** - * - * Multi-Protocol Serial Controller Routines (MPSC) - * - ****************************************************************************** - */ - -static void mpsc_hw_init(struct mpsc_port_info *pi) -{ - u32 v; - - pr_debug("mpsc_hw_init[%d]: Initializing hardware\n", pi->port.line); - - /* Set up clock routing */ - if (pi->mirror_regs) { - v = pi->shared_regs->MPSC_MRR_m; - v &= ~0x1c7; - pi->shared_regs->MPSC_MRR_m = v; - writel(v, pi->shared_regs->mpsc_routing_base + MPSC_MRR); - - v = pi->shared_regs->MPSC_RCRR_m; - v = (v & ~0xf0f) | 0x100; - pi->shared_regs->MPSC_RCRR_m = v; - writel(v, pi->shared_regs->mpsc_routing_base + MPSC_RCRR); - - v = pi->shared_regs->MPSC_TCRR_m; - v = (v & ~0xf0f) | 0x100; - pi->shared_regs->MPSC_TCRR_m = v; - writel(v, pi->shared_regs->mpsc_routing_base + MPSC_TCRR); - } else { - v = readl(pi->shared_regs->mpsc_routing_base + MPSC_MRR); - v &= ~0x1c7; - writel(v, pi->shared_regs->mpsc_routing_base + MPSC_MRR); - - v = readl(pi->shared_regs->mpsc_routing_base + MPSC_RCRR); - v = (v & ~0xf0f) | 0x100; - writel(v, pi->shared_regs->mpsc_routing_base + MPSC_RCRR); - - v = readl(pi->shared_regs->mpsc_routing_base + MPSC_TCRR); - v = (v & ~0xf0f) | 0x100; - writel(v, pi->shared_regs->mpsc_routing_base + MPSC_TCRR); - } - - /* Put MPSC in UART mode & enabel Tx/Rx egines */ - writel(0x000004c4, pi->mpsc_base + MPSC_MMCRL); - - /* No preamble, 16x divider, low-latency, */ - writel(0x04400400, pi->mpsc_base + MPSC_MMCRH); - mpsc_set_baudrate(pi, pi->default_baud); - - if (pi->mirror_regs) { - pi->MPSC_CHR_1_m = 0; - pi->MPSC_CHR_2_m = 0; - } - writel(0, pi->mpsc_base + MPSC_CHR_1); - writel(0, pi->mpsc_base + MPSC_CHR_2); - writel(pi->mpsc_max_idle, pi->mpsc_base + MPSC_CHR_3); - writel(0, pi->mpsc_base + MPSC_CHR_4); - writel(0, pi->mpsc_base + MPSC_CHR_5); - writel(0, pi->mpsc_base + MPSC_CHR_6); - writel(0, pi->mpsc_base + MPSC_CHR_7); - writel(0, pi->mpsc_base + MPSC_CHR_8); - writel(0, pi->mpsc_base + MPSC_CHR_9); - writel(0, pi->mpsc_base + MPSC_CHR_10); -} - -static void mpsc_enter_hunt(struct mpsc_port_info *pi) -{ - pr_debug("mpsc_enter_hunt[%d]: Hunting...\n", pi->port.line); - - if (pi->mirror_regs) { - writel(pi->MPSC_CHR_2_m | MPSC_CHR_2_EH, - pi->mpsc_base + MPSC_CHR_2); - /* Erratum prevents reading CHR_2 so just delay for a while */ - udelay(100); - } else { - writel(readl(pi->mpsc_base + MPSC_CHR_2) | MPSC_CHR_2_EH, - pi->mpsc_base + MPSC_CHR_2); - - while (readl(pi->mpsc_base + MPSC_CHR_2) & MPSC_CHR_2_EH) - udelay(10); - } -} - -static void mpsc_freeze(struct mpsc_port_info *pi) -{ - u32 v; - - pr_debug("mpsc_freeze[%d]: Freezing\n", pi->port.line); - - v = (pi->mirror_regs) ? pi->MPSC_MPCR_m : - readl(pi->mpsc_base + MPSC_MPCR); - v |= MPSC_MPCR_FRZ; - - if (pi->mirror_regs) - pi->MPSC_MPCR_m = v; - writel(v, pi->mpsc_base + MPSC_MPCR); -} - -static void mpsc_unfreeze(struct mpsc_port_info *pi) -{ - u32 v; - - v = (pi->mirror_regs) ? pi->MPSC_MPCR_m : - readl(pi->mpsc_base + MPSC_MPCR); - v &= ~MPSC_MPCR_FRZ; - - if (pi->mirror_regs) - pi->MPSC_MPCR_m = v; - writel(v, pi->mpsc_base + MPSC_MPCR); - - pr_debug("mpsc_unfreeze[%d]: Unfrozen\n", pi->port.line); -} - -static void mpsc_set_char_length(struct mpsc_port_info *pi, u32 len) -{ - u32 v; - - pr_debug("mpsc_set_char_length[%d]: char len: %d\n", pi->port.line,len); - - v = (pi->mirror_regs) ? pi->MPSC_MPCR_m : - readl(pi->mpsc_base + MPSC_MPCR); - v = (v & ~(0x3 << 12)) | ((len & 0x3) << 12); - - if (pi->mirror_regs) - pi->MPSC_MPCR_m = v; - writel(v, pi->mpsc_base + MPSC_MPCR); -} - -static void mpsc_set_stop_bit_length(struct mpsc_port_info *pi, u32 len) -{ - u32 v; - - pr_debug("mpsc_set_stop_bit_length[%d]: stop bits: %d\n", - pi->port.line, len); - - v = (pi->mirror_regs) ? pi->MPSC_MPCR_m : - readl(pi->mpsc_base + MPSC_MPCR); - - v = (v & ~(1 << 14)) | ((len & 0x1) << 14); - - if (pi->mirror_regs) - pi->MPSC_MPCR_m = v; - writel(v, pi->mpsc_base + MPSC_MPCR); -} - -static void mpsc_set_parity(struct mpsc_port_info *pi, u32 p) -{ - u32 v; - - pr_debug("mpsc_set_parity[%d]: parity bits: 0x%x\n", pi->port.line, p); - - v = (pi->mirror_regs) ? pi->MPSC_CHR_2_m : - readl(pi->mpsc_base + MPSC_CHR_2); - - p &= 0x3; - v = (v & ~0xc000c) | (p << 18) | (p << 2); - - if (pi->mirror_regs) - pi->MPSC_CHR_2_m = v; - writel(v, pi->mpsc_base + MPSC_CHR_2); -} - -/* - ****************************************************************************** - * - * Driver Init Routines - * - ****************************************************************************** - */ - -static void mpsc_init_hw(struct mpsc_port_info *pi) -{ - pr_debug("mpsc_init_hw[%d]: Initializing\n", pi->port.line); - - mpsc_brg_init(pi, pi->brg_clk_src); - mpsc_brg_enable(pi); - mpsc_sdma_init(pi, dma_get_cache_alignment()); /* burst a cacheline */ - mpsc_sdma_stop(pi); - mpsc_hw_init(pi); -} - -static int mpsc_alloc_ring_mem(struct mpsc_port_info *pi) -{ - int rc = 0; - - pr_debug("mpsc_alloc_ring_mem[%d]: Allocating ring mem\n", - pi->port.line); - - if (!pi->dma_region) { - if (!dma_set_mask(pi->port.dev, 0xffffffff)) { - printk(KERN_ERR "MPSC: Inadequate DMA support\n"); - rc = -ENXIO; - } else if ((pi->dma_region = dma_alloc_attrs(pi->port.dev, - MPSC_DMA_ALLOC_SIZE, - &pi->dma_region_p, GFP_KERNEL, - DMA_ATTR_NON_CONSISTENT)) - == NULL) { - printk(KERN_ERR "MPSC: Can't alloc Desc region\n"); - rc = -ENOMEM; - } - } - - return rc; -} - -static void mpsc_free_ring_mem(struct mpsc_port_info *pi) -{ - pr_debug("mpsc_free_ring_mem[%d]: Freeing ring mem\n", pi->port.line); - - if (pi->dma_region) { - dma_free_attrs(pi->port.dev, MPSC_DMA_ALLOC_SIZE, - pi->dma_region, pi->dma_region_p, - DMA_ATTR_NON_CONSISTENT); - pi->dma_region = NULL; - pi->dma_region_p = (dma_addr_t)NULL; - } -} - -static void mpsc_init_rings(struct mpsc_port_info *pi) -{ - struct mpsc_rx_desc *rxre; - struct mpsc_tx_desc *txre; - dma_addr_t dp, dp_p; - u8 *bp, *bp_p; - int i; - - pr_debug("mpsc_init_rings[%d]: Initializing rings\n", pi->port.line); - - BUG_ON(pi->dma_region == NULL); - - memset(pi->dma_region, 0, MPSC_DMA_ALLOC_SIZE); - - /* - * Descriptors & buffers are multiples of cacheline size and must be - * cacheline aligned. - */ - dp = ALIGN((u32)pi->dma_region, dma_get_cache_alignment()); - dp_p = ALIGN((u32)pi->dma_region_p, dma_get_cache_alignment()); - - /* - * Partition dma region into rx ring descriptor, rx buffers, - * tx ring descriptors, and tx buffers. - */ - pi->rxr = dp; - pi->rxr_p = dp_p; - dp += MPSC_RXR_SIZE; - dp_p += MPSC_RXR_SIZE; - - pi->rxb = (u8 *)dp; - pi->rxb_p = (u8 *)dp_p; - dp += MPSC_RXB_SIZE; - dp_p += MPSC_RXB_SIZE; - - pi->rxr_posn = 0; - - pi->txr = dp; - pi->txr_p = dp_p; - dp += MPSC_TXR_SIZE; - dp_p += MPSC_TXR_SIZE; - - pi->txb = (u8 *)dp; - pi->txb_p = (u8 *)dp_p; - - pi->txr_head = 0; - pi->txr_tail = 0; - - /* Init rx ring descriptors */ - dp = pi->rxr; - dp_p = pi->rxr_p; - bp = pi->rxb; - bp_p = pi->rxb_p; - - for (i = 0; i < MPSC_RXR_ENTRIES; i++) { - rxre = (struct mpsc_rx_desc *)dp; - - rxre->bufsize = cpu_to_be16(MPSC_RXBE_SIZE); - rxre->bytecnt = cpu_to_be16(0); - rxre->cmdstat = cpu_to_be32(SDMA_DESC_CMDSTAT_O - | SDMA_DESC_CMDSTAT_EI | SDMA_DESC_CMDSTAT_F - | SDMA_DESC_CMDSTAT_L); - rxre->link = cpu_to_be32(dp_p + MPSC_RXRE_SIZE); - rxre->buf_ptr = cpu_to_be32(bp_p); - - dp += MPSC_RXRE_SIZE; - dp_p += MPSC_RXRE_SIZE; - bp += MPSC_RXBE_SIZE; - bp_p += MPSC_RXBE_SIZE; - } - rxre->link = cpu_to_be32(pi->rxr_p); /* Wrap last back to first */ - - /* Init tx ring descriptors */ - dp = pi->txr; - dp_p = pi->txr_p; - bp = pi->txb; - bp_p = pi->txb_p; - - for (i = 0; i < MPSC_TXR_ENTRIES; i++) { - txre = (struct mpsc_tx_desc *)dp; - - txre->link = cpu_to_be32(dp_p + MPSC_TXRE_SIZE); - txre->buf_ptr = cpu_to_be32(bp_p); - - dp += MPSC_TXRE_SIZE; - dp_p += MPSC_TXRE_SIZE; - bp += MPSC_TXBE_SIZE; - bp_p += MPSC_TXBE_SIZE; - } - txre->link = cpu_to_be32(pi->txr_p); /* Wrap last back to first */ - - dma_cache_sync(pi->port.dev, (void *)pi->dma_region, - MPSC_DMA_ALLOC_SIZE, DMA_BIDIRECTIONAL); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - flush_dcache_range((ulong)pi->dma_region, - (ulong)pi->dma_region - + MPSC_DMA_ALLOC_SIZE); -#endif - - return; -} - -static void mpsc_uninit_rings(struct mpsc_port_info *pi) -{ - pr_debug("mpsc_uninit_rings[%d]: Uninitializing rings\n",pi->port.line); - - BUG_ON(pi->dma_region == NULL); - - pi->rxr = 0; - pi->rxr_p = 0; - pi->rxb = NULL; - pi->rxb_p = NULL; - pi->rxr_posn = 0; - - pi->txr = 0; - pi->txr_p = 0; - pi->txb = NULL; - pi->txb_p = NULL; - pi->txr_head = 0; - pi->txr_tail = 0; -} - -static int mpsc_make_ready(struct mpsc_port_info *pi) -{ - int rc; - - pr_debug("mpsc_make_ready[%d]: Making cltr ready\n", pi->port.line); - - if (!pi->ready) { - mpsc_init_hw(pi); - rc = mpsc_alloc_ring_mem(pi); - if (rc) - return rc; - mpsc_init_rings(pi); - pi->ready = 1; - } - - return 0; -} - -#ifdef CONFIG_CONSOLE_POLL -static int serial_polled; -#endif - -/* - ****************************************************************************** - * - * Interrupt Handling Routines - * - ****************************************************************************** - */ - -static int mpsc_rx_intr(struct mpsc_port_info *pi, unsigned long *flags) -{ - struct mpsc_rx_desc *rxre; - struct tty_port *port = &pi->port.state->port; - u32 cmdstat, bytes_in, i; - int rc = 0; - u8 *bp; - char flag = TTY_NORMAL; - - pr_debug("mpsc_rx_intr[%d]: Handling Rx intr\n", pi->port.line); - - rxre = (struct mpsc_rx_desc *)(pi->rxr + (pi->rxr_posn*MPSC_RXRE_SIZE)); - - dma_cache_sync(pi->port.dev, (void *)rxre, MPSC_RXRE_SIZE, - DMA_FROM_DEVICE); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - invalidate_dcache_range((ulong)rxre, - (ulong)rxre + MPSC_RXRE_SIZE); -#endif - - /* - * Loop through Rx descriptors handling ones that have been completed. - */ - while (!((cmdstat = be32_to_cpu(rxre->cmdstat)) - & SDMA_DESC_CMDSTAT_O)) { - bytes_in = be16_to_cpu(rxre->bytecnt); -#ifdef CONFIG_CONSOLE_POLL - if (unlikely(serial_polled)) { - serial_polled = 0; - return 0; - } -#endif - /* Following use of tty struct directly is deprecated */ - if (tty_buffer_request_room(port, bytes_in) < bytes_in) { - if (port->low_latency) { - spin_unlock_irqrestore(&pi->port.lock, *flags); - tty_flip_buffer_push(port); - spin_lock_irqsave(&pi->port.lock, *flags); - } - /* - * If this failed then we will throw away the bytes - * but must do so to clear interrupts. - */ - } - - bp = pi->rxb + (pi->rxr_posn * MPSC_RXBE_SIZE); - dma_cache_sync(pi->port.dev, (void *)bp, MPSC_RXBE_SIZE, - DMA_FROM_DEVICE); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - invalidate_dcache_range((ulong)bp, - (ulong)bp + MPSC_RXBE_SIZE); -#endif - - /* - * Other than for parity error, the manual provides little - * info on what data will be in a frame flagged by any of - * these errors. For parity error, it is the last byte in - * the buffer that had the error. As for the rest, I guess - * we'll assume there is no data in the buffer. - * If there is...it gets lost. - */ - if (unlikely(cmdstat & (SDMA_DESC_CMDSTAT_BR - | SDMA_DESC_CMDSTAT_FR - | SDMA_DESC_CMDSTAT_OR))) { - - pi->port.icount.rx++; - - if (cmdstat & SDMA_DESC_CMDSTAT_BR) { /* Break */ - pi->port.icount.brk++; - - if (uart_handle_break(&pi->port)) - goto next_frame; - } else if (cmdstat & SDMA_DESC_CMDSTAT_FR) { - pi->port.icount.frame++; - } else if (cmdstat & SDMA_DESC_CMDSTAT_OR) { - pi->port.icount.overrun++; - } - - cmdstat &= pi->port.read_status_mask; - - if (cmdstat & SDMA_DESC_CMDSTAT_BR) - flag = TTY_BREAK; - else if (cmdstat & SDMA_DESC_CMDSTAT_FR) - flag = TTY_FRAME; - else if (cmdstat & SDMA_DESC_CMDSTAT_OR) - flag = TTY_OVERRUN; - else if (cmdstat & SDMA_DESC_CMDSTAT_PE) - flag = TTY_PARITY; - } - - if (uart_handle_sysrq_char(&pi->port, *bp)) { - bp++; - bytes_in--; -#ifdef CONFIG_CONSOLE_POLL - if (unlikely(serial_polled)) { - serial_polled = 0; - return 0; - } -#endif - goto next_frame; - } - - if ((unlikely(cmdstat & (SDMA_DESC_CMDSTAT_BR - | SDMA_DESC_CMDSTAT_FR - | SDMA_DESC_CMDSTAT_OR))) - && !(cmdstat & pi->port.ignore_status_mask)) { - tty_insert_flip_char(port, *bp, flag); - } else { - for (i=0; i<bytes_in; i++) - tty_insert_flip_char(port, *bp++, TTY_NORMAL); - - pi->port.icount.rx += bytes_in; - } - -next_frame: - rxre->bytecnt = cpu_to_be16(0); - wmb(); - rxre->cmdstat = cpu_to_be32(SDMA_DESC_CMDSTAT_O - | SDMA_DESC_CMDSTAT_EI | SDMA_DESC_CMDSTAT_F - | SDMA_DESC_CMDSTAT_L); - wmb(); - dma_cache_sync(pi->port.dev, (void *)rxre, MPSC_RXRE_SIZE, - DMA_BIDIRECTIONAL); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - flush_dcache_range((ulong)rxre, - (ulong)rxre + MPSC_RXRE_SIZE); -#endif - - /* Advance to next descriptor */ - pi->rxr_posn = (pi->rxr_posn + 1) & (MPSC_RXR_ENTRIES - 1); - rxre = (struct mpsc_rx_desc *) - (pi->rxr + (pi->rxr_posn * MPSC_RXRE_SIZE)); - dma_cache_sync(pi->port.dev, (void *)rxre, MPSC_RXRE_SIZE, - DMA_FROM_DEVICE); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - invalidate_dcache_range((ulong)rxre, - (ulong)rxre + MPSC_RXRE_SIZE); -#endif - rc = 1; - } - - /* Restart rx engine, if its stopped */ - if ((readl(pi->sdma_base + SDMA_SDCM) & SDMA_SDCM_ERD) == 0) - mpsc_start_rx(pi); - - spin_unlock_irqrestore(&pi->port.lock, *flags); - tty_flip_buffer_push(port); - spin_lock_irqsave(&pi->port.lock, *flags); - return rc; -} - -static void mpsc_setup_tx_desc(struct mpsc_port_info *pi, u32 count, u32 intr) -{ - struct mpsc_tx_desc *txre; - - txre = (struct mpsc_tx_desc *)(pi->txr - + (pi->txr_head * MPSC_TXRE_SIZE)); - - txre->bytecnt = cpu_to_be16(count); - txre->shadow = txre->bytecnt; - wmb(); /* ensure cmdstat is last field updated */ - txre->cmdstat = cpu_to_be32(SDMA_DESC_CMDSTAT_O | SDMA_DESC_CMDSTAT_F - | SDMA_DESC_CMDSTAT_L - | ((intr) ? SDMA_DESC_CMDSTAT_EI : 0)); - wmb(); - dma_cache_sync(pi->port.dev, (void *)txre, MPSC_TXRE_SIZE, - DMA_BIDIRECTIONAL); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - flush_dcache_range((ulong)txre, - (ulong)txre + MPSC_TXRE_SIZE); -#endif -} - -static void mpsc_copy_tx_data(struct mpsc_port_info *pi) -{ - struct circ_buf *xmit = &pi->port.state->xmit; - u8 *bp; - u32 i; - - /* Make sure the desc ring isn't full */ - while (CIRC_CNT(pi->txr_head, pi->txr_tail, MPSC_TXR_ENTRIES) - < (MPSC_TXR_ENTRIES - 1)) { - if (pi->port.x_char) { - /* - * Ideally, we should use the TCS field in - * CHR_1 to put the x_char out immediately but - * errata prevents us from being able to read - * CHR_2 to know that its safe to write to - * CHR_1. Instead, just put it in-band with - * all the other Tx data. - */ - bp = pi->txb + (pi->txr_head * MPSC_TXBE_SIZE); - *bp = pi->port.x_char; - pi->port.x_char = 0; - i = 1; - } else if (!uart_circ_empty(xmit) - && !uart_tx_stopped(&pi->port)) { - i = min((u32)MPSC_TXBE_SIZE, - (u32)uart_circ_chars_pending(xmit)); - i = min(i, (u32)CIRC_CNT_TO_END(xmit->head, xmit->tail, - UART_XMIT_SIZE)); - bp = pi->txb + (pi->txr_head * MPSC_TXBE_SIZE); - memcpy(bp, &xmit->buf[xmit->tail], i); - xmit->tail = (xmit->tail + i) & (UART_XMIT_SIZE - 1); - - if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) - uart_write_wakeup(&pi->port); - } else { /* All tx data copied into ring bufs */ - return; - } - - dma_cache_sync(pi->port.dev, (void *)bp, MPSC_TXBE_SIZE, - DMA_BIDIRECTIONAL); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - flush_dcache_range((ulong)bp, - (ulong)bp + MPSC_TXBE_SIZE); -#endif - mpsc_setup_tx_desc(pi, i, 1); - - /* Advance to next descriptor */ - pi->txr_head = (pi->txr_head + 1) & (MPSC_TXR_ENTRIES - 1); - } -} - -static int mpsc_tx_intr(struct mpsc_port_info *pi) -{ - struct mpsc_tx_desc *txre; - int rc = 0; - unsigned long iflags; - - spin_lock_irqsave(&pi->tx_lock, iflags); - - if (!mpsc_sdma_tx_active(pi)) { - txre = (struct mpsc_tx_desc *)(pi->txr - + (pi->txr_tail * MPSC_TXRE_SIZE)); - - dma_cache_sync(pi->port.dev, (void *)txre, MPSC_TXRE_SIZE, - DMA_FROM_DEVICE); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - invalidate_dcache_range((ulong)txre, - (ulong)txre + MPSC_TXRE_SIZE); -#endif - - while (!(be32_to_cpu(txre->cmdstat) & SDMA_DESC_CMDSTAT_O)) { - rc = 1; - pi->port.icount.tx += be16_to_cpu(txre->bytecnt); - pi->txr_tail = (pi->txr_tail+1) & (MPSC_TXR_ENTRIES-1); - - /* If no more data to tx, fall out of loop */ - if (pi->txr_head == pi->txr_tail) - break; - - txre = (struct mpsc_tx_desc *)(pi->txr - + (pi->txr_tail * MPSC_TXRE_SIZE)); - dma_cache_sync(pi->port.dev, (void *)txre, - MPSC_TXRE_SIZE, DMA_FROM_DEVICE); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - invalidate_dcache_range((ulong)txre, - (ulong)txre + MPSC_TXRE_SIZE); -#endif - } - - mpsc_copy_tx_data(pi); - mpsc_sdma_start_tx(pi); /* start next desc if ready */ - } - - spin_unlock_irqrestore(&pi->tx_lock, iflags); - return rc; -} - -/* - * This is the driver's interrupt handler. To avoid a race, we first clear - * the interrupt, then handle any completed Rx/Tx descriptors. When done - * handling those descriptors, we restart the Rx/Tx engines if they're stopped. - */ -static irqreturn_t mpsc_sdma_intr(int irq, void *dev_id) -{ - struct mpsc_port_info *pi = dev_id; - ulong iflags; - int rc = IRQ_NONE; - - pr_debug("mpsc_sdma_intr[%d]: SDMA Interrupt Received\n",pi->port.line); - - spin_lock_irqsave(&pi->port.lock, iflags); - mpsc_sdma_intr_ack(pi); - if (mpsc_rx_intr(pi, &iflags)) - rc = IRQ_HANDLED; - if (mpsc_tx_intr(pi)) - rc = IRQ_HANDLED; - spin_unlock_irqrestore(&pi->port.lock, iflags); - - pr_debug("mpsc_sdma_intr[%d]: SDMA Interrupt Handled\n", pi->port.line); - return rc; -} - -/* - ****************************************************************************** - * - * serial_core.c Interface routines - * - ****************************************************************************** - */ -static uint mpsc_tx_empty(struct uart_port *port) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - ulong iflags; - uint rc; - - spin_lock_irqsave(&pi->port.lock, iflags); - rc = mpsc_sdma_tx_active(pi) ? 0 : TIOCSER_TEMT; - spin_unlock_irqrestore(&pi->port.lock, iflags); - - return rc; -} - -static void mpsc_set_mctrl(struct uart_port *port, uint mctrl) -{ - /* Have no way to set modem control lines AFAICT */ -} - -static uint mpsc_get_mctrl(struct uart_port *port) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - u32 mflags, status; - - status = (pi->mirror_regs) ? pi->MPSC_CHR_10_m - : readl(pi->mpsc_base + MPSC_CHR_10); - - mflags = 0; - if (status & 0x1) - mflags |= TIOCM_CTS; - if (status & 0x2) - mflags |= TIOCM_CAR; - - return mflags | TIOCM_DSR; /* No way to tell if DSR asserted */ -} - -static void mpsc_stop_tx(struct uart_port *port) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - - pr_debug("mpsc_stop_tx[%d]\n", port->line); - - mpsc_freeze(pi); -} - -static void mpsc_start_tx(struct uart_port *port) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - unsigned long iflags; - - spin_lock_irqsave(&pi->tx_lock, iflags); - - mpsc_unfreeze(pi); - mpsc_copy_tx_data(pi); - mpsc_sdma_start_tx(pi); - - spin_unlock_irqrestore(&pi->tx_lock, iflags); - - pr_debug("mpsc_start_tx[%d]\n", port->line); -} - -static void mpsc_start_rx(struct mpsc_port_info *pi) -{ - pr_debug("mpsc_start_rx[%d]: Starting...\n", pi->port.line); - - if (pi->rcv_data) { - mpsc_enter_hunt(pi); - mpsc_sdma_cmd(pi, SDMA_SDCM_ERD); - } -} - -static void mpsc_stop_rx(struct uart_port *port) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - - pr_debug("mpsc_stop_rx[%d]: Stopping...\n", port->line); - - if (pi->mirror_regs) { - writel(pi->MPSC_CHR_2_m | MPSC_CHR_2_RA, - pi->mpsc_base + MPSC_CHR_2); - /* Erratum prevents reading CHR_2 so just delay for a while */ - udelay(100); - } else { - writel(readl(pi->mpsc_base + MPSC_CHR_2) | MPSC_CHR_2_RA, - pi->mpsc_base + MPSC_CHR_2); - - while (readl(pi->mpsc_base + MPSC_CHR_2) & MPSC_CHR_2_RA) - udelay(10); - } - - mpsc_sdma_cmd(pi, SDMA_SDCM_AR); -} - -static void mpsc_break_ctl(struct uart_port *port, int ctl) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - ulong flags; - u32 v; - - v = ctl ? 0x00ff0000 : 0; - - spin_lock_irqsave(&pi->port.lock, flags); - if (pi->mirror_regs) - pi->MPSC_CHR_1_m = v; - writel(v, pi->mpsc_base + MPSC_CHR_1); - spin_unlock_irqrestore(&pi->port.lock, flags); -} - -static int mpsc_startup(struct uart_port *port) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - u32 flag = 0; - int rc; - - pr_debug("mpsc_startup[%d]: Starting up MPSC, irq: %d\n", - port->line, pi->port.irq); - - if ((rc = mpsc_make_ready(pi)) == 0) { - /* Setup IRQ handler */ - mpsc_sdma_intr_ack(pi); - - /* If irq's are shared, need to set flag */ - if (mpsc_ports[0].port.irq == mpsc_ports[1].port.irq) - flag = IRQF_SHARED; - - if (request_irq(pi->port.irq, mpsc_sdma_intr, flag, - "mpsc-sdma", pi)) - printk(KERN_ERR "MPSC: Can't get SDMA IRQ %d\n", - pi->port.irq); - - mpsc_sdma_intr_unmask(pi, 0xf); - mpsc_sdma_set_rx_ring(pi, (struct mpsc_rx_desc *)(pi->rxr_p - + (pi->rxr_posn * MPSC_RXRE_SIZE))); - } - - return rc; -} - -static void mpsc_shutdown(struct uart_port *port) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - - pr_debug("mpsc_shutdown[%d]: Shutting down MPSC\n", port->line); - - mpsc_sdma_stop(pi); - free_irq(pi->port.irq, pi); -} - -static void mpsc_set_termios(struct uart_port *port, struct ktermios *termios, - struct ktermios *old) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - u32 baud; - ulong flags; - u32 chr_bits, stop_bits, par; - - switch (termios->c_cflag & CSIZE) { - case CS5: - chr_bits = MPSC_MPCR_CL_5; - break; - case CS6: - chr_bits = MPSC_MPCR_CL_6; - break; - case CS7: - chr_bits = MPSC_MPCR_CL_7; - break; - case CS8: - default: - chr_bits = MPSC_MPCR_CL_8; - break; - } - - if (termios->c_cflag & CSTOPB) - stop_bits = MPSC_MPCR_SBL_2; - else - stop_bits = MPSC_MPCR_SBL_1; - - par = MPSC_CHR_2_PAR_EVEN; - if (termios->c_cflag & PARENB) - if (termios->c_cflag & PARODD) - par = MPSC_CHR_2_PAR_ODD; -#ifdef CMSPAR - if (termios->c_cflag & CMSPAR) { - if (termios->c_cflag & PARODD) - par = MPSC_CHR_2_PAR_MARK; - else - par = MPSC_CHR_2_PAR_SPACE; - } -#endif - - baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk); - - spin_lock_irqsave(&pi->port.lock, flags); - - uart_update_timeout(port, termios->c_cflag, baud); - - mpsc_set_char_length(pi, chr_bits); - mpsc_set_stop_bit_length(pi, stop_bits); - mpsc_set_parity(pi, par); - mpsc_set_baudrate(pi, baud); - - /* Characters/events to read */ - pi->port.read_status_mask = SDMA_DESC_CMDSTAT_OR; - - if (termios->c_iflag & INPCK) - pi->port.read_status_mask |= SDMA_DESC_CMDSTAT_PE - | SDMA_DESC_CMDSTAT_FR; - - if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) - pi->port.read_status_mask |= SDMA_DESC_CMDSTAT_BR; - - /* Characters/events to ignore */ - pi->port.ignore_status_mask = 0; - - if (termios->c_iflag & IGNPAR) - pi->port.ignore_status_mask |= SDMA_DESC_CMDSTAT_PE - | SDMA_DESC_CMDSTAT_FR; - - if (termios->c_iflag & IGNBRK) { - pi->port.ignore_status_mask |= SDMA_DESC_CMDSTAT_BR; - - if (termios->c_iflag & IGNPAR) - pi->port.ignore_status_mask |= SDMA_DESC_CMDSTAT_OR; - } - - if ((termios->c_cflag & CREAD)) { - if (!pi->rcv_data) { - pi->rcv_data = 1; - mpsc_start_rx(pi); - } - } else if (pi->rcv_data) { - mpsc_stop_rx(port); - pi->rcv_data = 0; - } - - spin_unlock_irqrestore(&pi->port.lock, flags); -} - -static const char *mpsc_type(struct uart_port *port) -{ - pr_debug("mpsc_type[%d]: port type: %s\n", port->line,MPSC_DRIVER_NAME); - return MPSC_DRIVER_NAME; -} - -static int mpsc_request_port(struct uart_port *port) -{ - /* Should make chip/platform specific call */ - return 0; -} - -static void mpsc_release_port(struct uart_port *port) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - - if (pi->ready) { - mpsc_uninit_rings(pi); - mpsc_free_ring_mem(pi); - pi->ready = 0; - } -} - -static void mpsc_config_port(struct uart_port *port, int flags) -{ -} - -static int mpsc_verify_port(struct uart_port *port, struct serial_struct *ser) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - int rc = 0; - - pr_debug("mpsc_verify_port[%d]: Verifying port data\n", pi->port.line); - - if (ser->type != PORT_UNKNOWN && ser->type != PORT_MPSC) - rc = -EINVAL; - else if (pi->port.irq != ser->irq) - rc = -EINVAL; - else if (ser->io_type != SERIAL_IO_MEM) - rc = -EINVAL; - else if (pi->port.uartclk / 16 != ser->baud_base) /* Not sure */ - rc = -EINVAL; - else if ((void *)pi->port.mapbase != ser->iomem_base) - rc = -EINVAL; - else if (pi->port.iobase != ser->port) - rc = -EINVAL; - else if (ser->hub6 != 0) - rc = -EINVAL; - - return rc; -} -#ifdef CONFIG_CONSOLE_POLL -/* Serial polling routines for writing and reading from the uart while - * in an interrupt or debug context. - */ - -static char poll_buf[2048]; -static int poll_ptr; -static int poll_cnt; -static void mpsc_put_poll_char(struct uart_port *port, - unsigned char c); - -static int mpsc_get_poll_char(struct uart_port *port) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - struct mpsc_rx_desc *rxre; - u32 cmdstat, bytes_in, i; - u8 *bp; - - if (!serial_polled) - serial_polled = 1; - - pr_debug("mpsc_rx_intr[%d]: Handling Rx intr\n", pi->port.line); - - if (poll_cnt) { - poll_cnt--; - return poll_buf[poll_ptr++]; - } - poll_ptr = 0; - poll_cnt = 0; - - while (poll_cnt == 0) { - rxre = (struct mpsc_rx_desc *)(pi->rxr + - (pi->rxr_posn*MPSC_RXRE_SIZE)); - dma_cache_sync(pi->port.dev, (void *)rxre, - MPSC_RXRE_SIZE, DMA_FROM_DEVICE); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - invalidate_dcache_range((ulong)rxre, - (ulong)rxre + MPSC_RXRE_SIZE); -#endif - /* - * Loop through Rx descriptors handling ones that have - * been completed. - */ - while (poll_cnt == 0 && - !((cmdstat = be32_to_cpu(rxre->cmdstat)) & - SDMA_DESC_CMDSTAT_O)){ - bytes_in = be16_to_cpu(rxre->bytecnt); - bp = pi->rxb + (pi->rxr_posn * MPSC_RXBE_SIZE); - dma_cache_sync(pi->port.dev, (void *) bp, - MPSC_RXBE_SIZE, DMA_FROM_DEVICE); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - invalidate_dcache_range((ulong)bp, - (ulong)bp + MPSC_RXBE_SIZE); -#endif - if ((unlikely(cmdstat & (SDMA_DESC_CMDSTAT_BR | - SDMA_DESC_CMDSTAT_FR | SDMA_DESC_CMDSTAT_OR))) && - !(cmdstat & pi->port.ignore_status_mask)) { - poll_buf[poll_cnt] = *bp; - poll_cnt++; - } else { - for (i = 0; i < bytes_in; i++) { - poll_buf[poll_cnt] = *bp++; - poll_cnt++; - } - pi->port.icount.rx += bytes_in; - } - rxre->bytecnt = cpu_to_be16(0); - wmb(); - rxre->cmdstat = cpu_to_be32(SDMA_DESC_CMDSTAT_O | - SDMA_DESC_CMDSTAT_EI | - SDMA_DESC_CMDSTAT_F | - SDMA_DESC_CMDSTAT_L); - wmb(); - dma_cache_sync(pi->port.dev, (void *)rxre, - MPSC_RXRE_SIZE, DMA_BIDIRECTIONAL); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - flush_dcache_range((ulong)rxre, - (ulong)rxre + MPSC_RXRE_SIZE); -#endif - - /* Advance to next descriptor */ - pi->rxr_posn = (pi->rxr_posn + 1) & - (MPSC_RXR_ENTRIES - 1); - rxre = (struct mpsc_rx_desc *)(pi->rxr + - (pi->rxr_posn * MPSC_RXRE_SIZE)); - dma_cache_sync(pi->port.dev, (void *)rxre, - MPSC_RXRE_SIZE, DMA_FROM_DEVICE); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - invalidate_dcache_range((ulong)rxre, - (ulong)rxre + MPSC_RXRE_SIZE); -#endif - } - - /* Restart rx engine, if its stopped */ - if ((readl(pi->sdma_base + SDMA_SDCM) & SDMA_SDCM_ERD) == 0) - mpsc_start_rx(pi); - } - if (poll_cnt) { - poll_cnt--; - return poll_buf[poll_ptr++]; - } - - return 0; -} - - -static void mpsc_put_poll_char(struct uart_port *port, - unsigned char c) -{ - struct mpsc_port_info *pi = - container_of(port, struct mpsc_port_info, port); - u32 data; - - data = readl(pi->mpsc_base + MPSC_MPCR); - writeb(c, pi->mpsc_base + MPSC_CHR_1); - mb(); - data = readl(pi->mpsc_base + MPSC_CHR_2); - data |= MPSC_CHR_2_TTCS; - writel(data, pi->mpsc_base + MPSC_CHR_2); - mb(); - - while (readl(pi->mpsc_base + MPSC_CHR_2) & MPSC_CHR_2_TTCS); -} -#endif - -static const struct uart_ops mpsc_pops = { - .tx_empty = mpsc_tx_empty, - .set_mctrl = mpsc_set_mctrl, - .get_mctrl = mpsc_get_mctrl, - .stop_tx = mpsc_stop_tx, - .start_tx = mpsc_start_tx, - .stop_rx = mpsc_stop_rx, - .break_ctl = mpsc_break_ctl, - .startup = mpsc_startup, - .shutdown = mpsc_shutdown, - .set_termios = mpsc_set_termios, - .type = mpsc_type, - .release_port = mpsc_release_port, - .request_port = mpsc_request_port, - .config_port = mpsc_config_port, - .verify_port = mpsc_verify_port, -#ifdef CONFIG_CONSOLE_POLL - .poll_get_char = mpsc_get_poll_char, - .poll_put_char = mpsc_put_poll_char, -#endif -}; - -/* - ****************************************************************************** - * - * Console Interface Routines - * - ****************************************************************************** - */ - -#ifdef CONFIG_SERIAL_MPSC_CONSOLE -static void mpsc_console_write(struct console *co, const char *s, uint count) -{ - struct mpsc_port_info *pi = &mpsc_ports[co->index]; - u8 *bp, *dp, add_cr = 0; - int i; - unsigned long iflags; - - spin_lock_irqsave(&pi->tx_lock, iflags); - - while (pi->txr_head != pi->txr_tail) { - while (mpsc_sdma_tx_active(pi)) - udelay(100); - mpsc_sdma_intr_ack(pi); - mpsc_tx_intr(pi); - } - - while (mpsc_sdma_tx_active(pi)) - udelay(100); - - while (count > 0) { - bp = dp = pi->txb + (pi->txr_head * MPSC_TXBE_SIZE); - - for (i = 0; i < MPSC_TXBE_SIZE; i++) { - if (count == 0) - break; - - if (add_cr) { - *(dp++) = '\r'; - add_cr = 0; - } else { - *(dp++) = *s; - - if (*(s++) == '\n') { /* add '\r' after '\n' */ - add_cr = 1; - count++; - } - } - - count--; - } - - dma_cache_sync(pi->port.dev, (void *)bp, MPSC_TXBE_SIZE, - DMA_BIDIRECTIONAL); -#if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) - if (pi->cache_mgmt) /* GT642[46]0 Res #COMM-2 */ - flush_dcache_range((ulong)bp, - (ulong)bp + MPSC_TXBE_SIZE); -#endif - mpsc_setup_tx_desc(pi, i, 0); - pi->txr_head = (pi->txr_head + 1) & (MPSC_TXR_ENTRIES - 1); - mpsc_sdma_start_tx(pi); - - while (mpsc_sdma_tx_active(pi)) - udelay(100); - - pi->txr_tail = (pi->txr_tail + 1) & (MPSC_TXR_ENTRIES - 1); - } - - spin_unlock_irqrestore(&pi->tx_lock, iflags); -} - -static int __init mpsc_console_setup(struct console *co, char *options) -{ - struct mpsc_port_info *pi; - int baud, bits, parity, flow; - - pr_debug("mpsc_console_setup[%d]: options: %s\n", co->index, options); - - if (co->index >= MPSC_NUM_CTLRS) - co->index = 0; - - pi = &mpsc_ports[co->index]; - - baud = pi->default_baud; - bits = pi->default_bits; - parity = pi->default_parity; - flow = pi->default_flow; - - if (!pi->port.ops) - return -ENODEV; - - spin_lock_init(&pi->port.lock); /* Temporary fix--copied from 8250.c */ - - if (options) - uart_parse_options(options, &baud, &parity, &bits, &flow); - - return uart_set_options(&pi->port, co, baud, parity, bits, flow); -} - -static struct console mpsc_console = { - .name = MPSC_DEV_NAME, - .write = mpsc_console_write, - .device = uart_console_device, - .setup = mpsc_console_setup, - .flags = CON_PRINTBUFFER, - .index = -1, - .data = &mpsc_reg, -}; - -static int __init mpsc_late_console_init(void) -{ - pr_debug("mpsc_late_console_init: Enter\n"); - - if (!(mpsc_console.flags & CON_ENABLED)) - register_console(&mpsc_console); - return 0; -} - -late_initcall(mpsc_late_console_init); - -#define MPSC_CONSOLE &mpsc_console -#else -#define MPSC_CONSOLE NULL -#endif -/* - ****************************************************************************** - * - * Dummy Platform Driver to extract & map shared register regions - * - ****************************************************************************** - */ -static void mpsc_resource_err(char *s) -{ - printk(KERN_WARNING "MPSC: Platform device resource error in %s\n", s); -} - -static int mpsc_shared_map_regs(struct platform_device *pd) -{ - struct resource *r; - - if ((r = platform_get_resource(pd, IORESOURCE_MEM, - MPSC_ROUTING_BASE_ORDER)) - && request_mem_region(r->start, - MPSC_ROUTING_REG_BLOCK_SIZE, - "mpsc_routing_regs")) { - mpsc_shared_regs.mpsc_routing_base = ioremap(r->start, - MPSC_ROUTING_REG_BLOCK_SIZE); - mpsc_shared_regs.mpsc_routing_base_p = r->start; - } else { - mpsc_resource_err("MPSC routing base"); - return -ENOMEM; - } - - if ((r = platform_get_resource(pd, IORESOURCE_MEM, - MPSC_SDMA_INTR_BASE_ORDER)) - && request_mem_region(r->start, - MPSC_SDMA_INTR_REG_BLOCK_SIZE, - "sdma_intr_regs")) { - mpsc_shared_regs.sdma_intr_base = ioremap(r->start, - MPSC_SDMA_INTR_REG_BLOCK_SIZE); - mpsc_shared_regs.sdma_intr_base_p = r->start; - } else { - iounmap(mpsc_shared_regs.mpsc_routing_base); - release_mem_region(mpsc_shared_regs.mpsc_routing_base_p, - MPSC_ROUTING_REG_BLOCK_SIZE); - mpsc_resource_err("SDMA intr base"); - return -ENOMEM; - } - - return 0; -} - -static void mpsc_shared_unmap_regs(void) -{ - if (mpsc_shared_regs.mpsc_routing_base) { - iounmap(mpsc_shared_regs.mpsc_routing_base); - release_mem_region(mpsc_shared_regs.mpsc_routing_base_p, - MPSC_ROUTING_REG_BLOCK_SIZE); - } - if (mpsc_shared_regs.sdma_intr_base) { - iounmap(mpsc_shared_regs.sdma_intr_base); - release_mem_region(mpsc_shared_regs.sdma_intr_base_p, - MPSC_SDMA_INTR_REG_BLOCK_SIZE); - } - - mpsc_shared_regs.mpsc_routing_base = NULL; - mpsc_shared_regs.sdma_intr_base = NULL; - - mpsc_shared_regs.mpsc_routing_base_p = 0; - mpsc_shared_regs.sdma_intr_base_p = 0; -} - -static int mpsc_shared_drv_probe(struct platform_device *dev) -{ - struct mpsc_shared_pdata *pdata; - int rc; - - if (dev->id != 0) - return -ENODEV; - - rc = mpsc_shared_map_regs(dev); - if (rc) - return rc; - - pdata = dev_get_platdata(&dev->dev); - - mpsc_shared_regs.MPSC_MRR_m = pdata->mrr_val; - mpsc_shared_regs.MPSC_RCRR_m= pdata->rcrr_val; - mpsc_shared_regs.MPSC_TCRR_m= pdata->tcrr_val; - mpsc_shared_regs.SDMA_INTR_CAUSE_m = pdata->intr_cause_val; - mpsc_shared_regs.SDMA_INTR_MASK_m = pdata->intr_mask_val; - - return 0; -} - -static int mpsc_shared_drv_remove(struct platform_device *dev) -{ - if (dev->id != 0) - return -ENODEV; - - mpsc_shared_unmap_regs(); - mpsc_shared_regs.MPSC_MRR_m = 0; - mpsc_shared_regs.MPSC_RCRR_m = 0; - mpsc_shared_regs.MPSC_TCRR_m = 0; - mpsc_shared_regs.SDMA_INTR_CAUSE_m = 0; - mpsc_shared_regs.SDMA_INTR_MASK_m = 0; - - return 0; -} - -static struct platform_driver mpsc_shared_driver = { - .probe = mpsc_shared_drv_probe, - .remove = mpsc_shared_drv_remove, - .driver = { - .name = MPSC_SHARED_NAME, - }, -}; - -/* - ****************************************************************************** - * - * Driver Interface Routines - * - ****************************************************************************** - */ -static struct uart_driver mpsc_reg = { - .owner = THIS_MODULE, - .driver_name = MPSC_DRIVER_NAME, - .dev_name = MPSC_DEV_NAME, - .major = MPSC_MAJOR, - .minor = MPSC_MINOR_START, - .nr = MPSC_NUM_CTLRS, - .cons = MPSC_CONSOLE, -}; - -static int mpsc_drv_map_regs(struct mpsc_port_info *pi, - struct platform_device *pd) -{ - struct resource *r; - - if ((r = platform_get_resource(pd, IORESOURCE_MEM, MPSC_BASE_ORDER)) - && request_mem_region(r->start, MPSC_REG_BLOCK_SIZE, - "mpsc_regs")) { - pi->mpsc_base = ioremap(r->start, MPSC_REG_BLOCK_SIZE); - pi->mpsc_base_p = r->start; - } else { - mpsc_resource_err("MPSC base"); - goto err; - } - - if ((r = platform_get_resource(pd, IORESOURCE_MEM, - MPSC_SDMA_BASE_ORDER)) - && request_mem_region(r->start, - MPSC_SDMA_REG_BLOCK_SIZE, "sdma_regs")) { - pi->sdma_base = ioremap(r->start,MPSC_SDMA_REG_BLOCK_SIZE); - pi->sdma_base_p = r->start; - } else { - mpsc_resource_err("SDMA base"); - goto err; - } - - if ((r = platform_get_resource(pd,IORESOURCE_MEM,MPSC_BRG_BASE_ORDER)) - && request_mem_region(r->start, - MPSC_BRG_REG_BLOCK_SIZE, "brg_regs")) { - pi->brg_base = ioremap(r->start, MPSC_BRG_REG_BLOCK_SIZE); - pi->brg_base_p = r->start; - } else { - mpsc_resource_err("BRG base"); - goto err; - } - return 0; - -err: - if (pi->sdma_base) { - iounmap(pi->sdma_base); - pi->sdma_base = NULL; - } - if (pi->mpsc_base) { - iounmap(pi->mpsc_base); - pi->mpsc_base = NULL; - } - return -ENOMEM; -} - -static void mpsc_drv_unmap_regs(struct mpsc_port_info *pi) -{ - if (pi->mpsc_base) { - iounmap(pi->mpsc_base); - release_mem_region(pi->mpsc_base_p, MPSC_REG_BLOCK_SIZE); - } - if (pi->sdma_base) { - iounmap(pi->sdma_base); - release_mem_region(pi->sdma_base_p, MPSC_SDMA_REG_BLOCK_SIZE); - } - if (pi->brg_base) { - iounmap(pi->brg_base); - release_mem_region(pi->brg_base_p, MPSC_BRG_REG_BLOCK_SIZE); - } - - pi->mpsc_base = NULL; - pi->sdma_base = NULL; - pi->brg_base = NULL; - - pi->mpsc_base_p = 0; - pi->sdma_base_p = 0; - pi->brg_base_p = 0; -} - -static void mpsc_drv_get_platform_data(struct mpsc_port_info *pi, - struct platform_device *pd, int num) -{ - struct mpsc_pdata *pdata; - - pdata = dev_get_platdata(&pd->dev); - - pi->port.uartclk = pdata->brg_clk_freq; - pi->port.iotype = UPIO_MEM; - pi->port.line = num; - pi->port.type = PORT_MPSC; - pi->port.fifosize = MPSC_TXBE_SIZE; - pi->port.membase = pi->mpsc_base; - pi->port.mapbase = (ulong)pi->mpsc_base; - pi->port.ops = &mpsc_pops; - - pi->mirror_regs = pdata->mirror_regs; - pi->cache_mgmt = pdata->cache_mgmt; - pi->brg_can_tune = pdata->brg_can_tune; - pi->brg_clk_src = pdata->brg_clk_src; - pi->mpsc_max_idle = pdata->max_idle; - pi->default_baud = pdata->default_baud; - pi->default_bits = pdata->default_bits; - pi->default_parity = pdata->default_parity; - pi->default_flow = pdata->default_flow; - - /* Initial values of mirrored regs */ - pi->MPSC_CHR_1_m = pdata->chr_1_val; - pi->MPSC_CHR_2_m = pdata->chr_2_val; - pi->MPSC_CHR_10_m = pdata->chr_10_val; - pi->MPSC_MPCR_m = pdata->mpcr_val; - pi->BRG_BCR_m = pdata->bcr_val; - - pi->shared_regs = &mpsc_shared_regs; - - pi->port.irq = platform_get_irq(pd, 0); -} - -static int mpsc_drv_probe(struct platform_device *dev) -{ - struct mpsc_port_info *pi; - int rc; - - dev_dbg(&dev->dev, "mpsc_drv_probe: Adding MPSC %d\n", dev->id); - - if (dev->id >= MPSC_NUM_CTLRS) - return -ENODEV; - - pi = &mpsc_ports[dev->id]; - - rc = mpsc_drv_map_regs(pi, dev); - if (rc) - return rc; - - mpsc_drv_get_platform_data(pi, dev, dev->id); - pi->port.dev = &dev->dev; - - rc = mpsc_make_ready(pi); - if (rc) - goto err_unmap; - - spin_lock_init(&pi->tx_lock); - rc = uart_add_one_port(&mpsc_reg, &pi->port); - if (rc) - goto err_relport; - - return 0; -err_relport: - mpsc_release_port(&pi->port); -err_unmap: - mpsc_drv_unmap_regs(pi); - return rc; -} - -static struct platform_driver mpsc_driver = { - .probe = mpsc_drv_probe, - .driver = { - .name = MPSC_CTLR_NAME, - .suppress_bind_attrs = true, - }, -}; - -static int __init mpsc_drv_init(void) -{ - int rc; - - printk(KERN_INFO "Serial: MPSC driver\n"); - - memset(mpsc_ports, 0, sizeof(mpsc_ports)); - memset(&mpsc_shared_regs, 0, sizeof(mpsc_shared_regs)); - - rc = uart_register_driver(&mpsc_reg); - if (rc) - return rc; - - rc = platform_driver_register(&mpsc_shared_driver); - if (rc) - goto err_unreg_uart; - - rc = platform_driver_register(&mpsc_driver); - if (rc) - goto err_unreg_plat; - - return 0; -err_unreg_plat: - platform_driver_unregister(&mpsc_shared_driver); -err_unreg_uart: - uart_unregister_driver(&mpsc_reg); - return rc; -} -device_initcall(mpsc_drv_init); - -/* -MODULE_AUTHOR("Mark A. Greer <mgreer@mvista.com>"); -MODULE_DESCRIPTION("Generic Marvell MPSC serial/UART driver"); -MODULE_LICENSE("GPL"); -*/ diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c index 23833ad952ba..3657a24913fc 100644 --- a/drivers/tty/serial/msm_serial.c +++ b/drivers/tty/serial/msm_serial.c @@ -383,10 +383,14 @@ no_rx: static inline void msm_wait_for_xmitr(struct uart_port *port) { + unsigned int timeout = 500000; + while (!(msm_read(port, UART_SR) & UART_SR_TX_EMPTY)) { if (msm_read(port, UART_ISR) & UART_ISR_TX_READY) break; udelay(1); + if (!timeout--) + break; } msm_write(port, UART_CR_CMD_RESET_TX_READY, UART_CR); } diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c index 83f4dd0bfd74..4223cb496764 100644 --- a/drivers/tty/serial/serial_core.c +++ b/drivers/tty/serial/serial_core.c @@ -1777,6 +1777,7 @@ static int uart_port_activate(struct tty_port *port, struct tty_struct *tty) { struct uart_state *state = container_of(port, struct uart_state, port); struct uart_port *uport; + int ret; uport = uart_port_check(state); if (!uport || uport->flags & UPF_DEAD) @@ -1787,7 +1788,11 @@ static int uart_port_activate(struct tty_port *port, struct tty_struct *tty) /* * Start up the serial port. */ - return uart_startup(tty, state, 0); + ret = uart_startup(tty, state, 0); + if (ret > 0) + tty_port_set_active(port, 1); + + return ret; } static const char *uart_type(struct uart_port *port) diff --git a/drivers/tty/serial/serial_mctrl_gpio.c b/drivers/tty/serial/serial_mctrl_gpio.c index 39ed56214cd3..2b400189be91 100644 --- a/drivers/tty/serial/serial_mctrl_gpio.c +++ b/drivers/tty/serial/serial_mctrl_gpio.c @@ -12,6 +12,7 @@ #include <linux/termios.h> #include <linux/serial_core.h> #include <linux/module.h> +#include <linux/property.h> #include "serial_mctrl_gpio.h" @@ -116,6 +117,19 @@ struct mctrl_gpios *mctrl_gpio_init_noauto(struct device *dev, unsigned int idx) for (i = 0; i < UART_GPIO_MAX; i++) { enum gpiod_flags flags; + char *gpio_str; + bool present; + + /* Check if GPIO property exists and continue if not */ + gpio_str = kasprintf(GFP_KERNEL, "%s-gpios", + mctrl_gpios_desc[i].name); + if (!gpio_str) + continue; + + present = device_property_present(dev, gpio_str); + kfree(gpio_str); + if (!present) + continue; if (mctrl_gpios_desc[i].dir_out) flags = GPIOD_OUT_LOW; diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c index abc705716aa0..d18c680aa64b 100644 --- a/drivers/tty/serial/sh-sci.c +++ b/drivers/tty/serial/sh-sci.c @@ -1398,6 +1398,7 @@ static void sci_dma_tx_work_fn(struct work_struct *work) struct circ_buf *xmit = &port->state->xmit; unsigned long flags; dma_addr_t buf; + int head, tail; /* * DMA is idle now. @@ -1407,16 +1408,23 @@ static void sci_dma_tx_work_fn(struct work_struct *work) * consistent xmit buffer state. */ spin_lock_irq(&port->lock); - buf = s->tx_dma_addr + (xmit->tail & (UART_XMIT_SIZE - 1)); + head = xmit->head; + tail = xmit->tail; + buf = s->tx_dma_addr + (tail & (UART_XMIT_SIZE - 1)); s->tx_dma_len = min_t(unsigned int, - CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE), - CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE)); - spin_unlock_irq(&port->lock); + CIRC_CNT(head, tail, UART_XMIT_SIZE), + CIRC_CNT_TO_END(head, tail, UART_XMIT_SIZE)); + if (!s->tx_dma_len) { + /* Transmit buffer has been flushed */ + spin_unlock_irq(&port->lock); + return; + } desc = dmaengine_prep_slave_single(chan, buf, s->tx_dma_len, DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); if (!desc) { + spin_unlock_irq(&port->lock); dev_warn(port->dev, "Failed preparing Tx DMA descriptor\n"); goto switch_to_pio; } @@ -1424,18 +1432,18 @@ static void sci_dma_tx_work_fn(struct work_struct *work) dma_sync_single_for_device(chan->device->dev, buf, s->tx_dma_len, DMA_TO_DEVICE); - spin_lock_irq(&port->lock); desc->callback = sci_dma_tx_complete; desc->callback_param = s; - spin_unlock_irq(&port->lock); s->cookie_tx = dmaengine_submit(desc); if (dma_submit_error(s->cookie_tx)) { + spin_unlock_irq(&port->lock); dev_warn(port->dev, "Failed submitting Tx DMA descriptor\n"); goto switch_to_pio; } + spin_unlock_irq(&port->lock); dev_dbg(port->dev, "%s: %p: %d...%d, cookie %d\n", - __func__, xmit->buf, xmit->tail, xmit->head, s->cookie_tx); + __func__, xmit->buf, tail, head, s->cookie_tx); dma_async_issue_pending(chan); return; @@ -1648,11 +1656,18 @@ static void sci_free_dma(struct uart_port *port) static void sci_flush_buffer(struct uart_port *port) { + struct sci_port *s = to_sci_port(port); + /* * In uart_flush_buffer(), the xmit circular buffer has just been - * cleared, so we have to reset tx_dma_len accordingly. + * cleared, so we have to reset tx_dma_len accordingly, and stop any + * pending transfers */ - to_sci_port(port)->tx_dma_len = 0; + s->tx_dma_len = 0; + if (s->chan_tx) { + dmaengine_terminate_async(s->chan_tx); + s->cookie_tx = -EINVAL; + } } #else /* !CONFIG_SERIAL_SH_SCI_DMA */ static inline void sci_request_dma(struct uart_port *port) diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c index e8d7a7bb4339..24a2261f879a 100644 --- a/drivers/tty/serial/stm32-usart.c +++ b/drivers/tty/serial/stm32-usart.c @@ -105,9 +105,7 @@ static int stm32_config_rs485(struct uart_port *port, struct stm32_usart_config *cfg = &stm32_port->info->cfg; u32 usartdiv, baud, cr1, cr3; bool over8; - unsigned long flags; - spin_lock_irqsave(&port->lock, flags); stm32_clr_bits(port, ofs->cr1, BIT(cfg->uart_enable_bit)); port->rs485 = *rs485conf; @@ -147,7 +145,6 @@ static int stm32_config_rs485(struct uart_port *port, } stm32_set_bits(port, ofs->cr1, BIT(cfg->uart_enable_bit)); - spin_unlock_irqrestore(&port->lock, flags); return 0; } @@ -194,8 +191,8 @@ static int stm32_pending_rx(struct uart_port *port, u32 *sr, int *last_res, return 0; } -static unsigned long -stm32_get_char(struct uart_port *port, u32 *sr, int *last_res) +static unsigned long stm32_get_char(struct uart_port *port, u32 *sr, + int *last_res) { struct stm32_port *stm32_port = to_stm32_port(port); struct stm32_usart_offsets *ofs = &stm32_port->info->ofs; @@ -205,10 +202,13 @@ stm32_get_char(struct uart_port *port, u32 *sr, int *last_res) c = stm32_port->rx_buf[RX_BUF_L - (*last_res)--]; if ((*last_res) == 0) *last_res = RX_BUF_L; - return c; } else { - return readl_relaxed(port->membase + ofs->rdr); + c = readl_relaxed(port->membase + ofs->rdr); + /* apply RDR data mask */ + c &= stm32_port->rdr_mask; } + + return c; } static void stm32_receive_chars(struct uart_port *port, bool threaded) @@ -225,35 +225,51 @@ static void stm32_receive_chars(struct uart_port *port, bool threaded) while (stm32_pending_rx(port, &sr, &stm32_port->last_res, threaded)) { sr |= USART_SR_DUMMY_RX; - c = stm32_get_char(port, &sr, &stm32_port->last_res); flag = TTY_NORMAL; - port->icount.rx++; + /* + * Status bits has to be cleared before reading the RDR: + * In FIFO mode, reading the RDR will pop the next data + * (if any) along with its status bits into the SR. + * Not doing so leads to misalignement between RDR and SR, + * and clear status bits of the next rx data. + * + * Clear errors flags for stm32f7 and stm32h7 compatible + * devices. On stm32f4 compatible devices, the error bit is + * cleared by the sequence [read SR - read DR]. + */ + if ((sr & USART_SR_ERR_MASK) && ofs->icr != UNDEF_REG) + stm32_clr_bits(port, ofs->icr, USART_ICR_ORECF | + USART_ICR_PECF | USART_ICR_FECF); + + c = stm32_get_char(port, &sr, &stm32_port->last_res); + port->icount.rx++; if (sr & USART_SR_ERR_MASK) { - if (sr & USART_SR_LBD) { - port->icount.brk++; - if (uart_handle_break(port)) - continue; - } else if (sr & USART_SR_ORE) { - if (ofs->icr != UNDEF_REG) - writel_relaxed(USART_ICR_ORECF, - port->membase + - ofs->icr); + if (sr & USART_SR_ORE) { port->icount.overrun++; } else if (sr & USART_SR_PE) { port->icount.parity++; } else if (sr & USART_SR_FE) { - port->icount.frame++; + /* Break detection if character is null */ + if (!c) { + port->icount.brk++; + if (uart_handle_break(port)) + continue; + } else { + port->icount.frame++; + } } sr &= port->read_status_mask; - if (sr & USART_SR_LBD) - flag = TTY_BREAK; - else if (sr & USART_SR_PE) + if (sr & USART_SR_PE) { flag = TTY_PARITY; - else if (sr & USART_SR_FE) - flag = TTY_FRAME; + } else if (sr & USART_SR_FE) { + if (!c) + flag = TTY_BREAK; + else + flag = TTY_FRAME; + } } if (uart_handle_sysrq_char(port, c)) @@ -271,21 +287,6 @@ static void stm32_tx_dma_complete(void *arg) struct uart_port *port = arg; struct stm32_port *stm32port = to_stm32_port(port); struct stm32_usart_offsets *ofs = &stm32port->info->ofs; - unsigned int isr; - int ret; - - ret = readl_relaxed_poll_timeout_atomic(port->membase + ofs->isr, - isr, - (isr & USART_SR_TC), - 10, 100000); - - if (ret) - dev_err(port->dev, "terminal count not set\n"); - - if (ofs->icr == UNDEF_REG) - stm32_clr_bits(port, ofs->isr, USART_SR_TC); - else - stm32_set_bits(port, ofs->icr, USART_CR_TC); stm32_clr_bits(port, ofs->cr3, USART_CR3_DMAT); stm32port->tx_dma_busy = false; @@ -294,32 +295,57 @@ static void stm32_tx_dma_complete(void *arg) stm32_transmit_chars(port); } +static void stm32_tx_interrupt_enable(struct uart_port *port) +{ + struct stm32_port *stm32_port = to_stm32_port(port); + struct stm32_usart_offsets *ofs = &stm32_port->info->ofs; + + /* + * Enables TX FIFO threashold irq when FIFO is enabled, + * or TX empty irq when FIFO is disabled + */ + if (stm32_port->fifoen) + stm32_set_bits(port, ofs->cr3, USART_CR3_TXFTIE); + else + stm32_set_bits(port, ofs->cr1, USART_CR1_TXEIE); +} + +static void stm32_tx_interrupt_disable(struct uart_port *port) +{ + struct stm32_port *stm32_port = to_stm32_port(port); + struct stm32_usart_offsets *ofs = &stm32_port->info->ofs; + + if (stm32_port->fifoen) + stm32_clr_bits(port, ofs->cr3, USART_CR3_TXFTIE); + else + stm32_clr_bits(port, ofs->cr1, USART_CR1_TXEIE); +} + static void stm32_transmit_chars_pio(struct uart_port *port) { struct stm32_port *stm32_port = to_stm32_port(port); struct stm32_usart_offsets *ofs = &stm32_port->info->ofs; struct circ_buf *xmit = &port->state->xmit; - unsigned int isr; - int ret; if (stm32_port->tx_dma_busy) { stm32_clr_bits(port, ofs->cr3, USART_CR3_DMAT); stm32_port->tx_dma_busy = false; } - ret = readl_relaxed_poll_timeout_atomic(port->membase + ofs->isr, - isr, - (isr & USART_SR_TXE), - 10, 100000); - - if (ret) - dev_err(port->dev, "tx empty not set\n"); - - stm32_set_bits(port, ofs->cr1, USART_CR1_TXEIE); + while (!uart_circ_empty(xmit)) { + /* Check that TDR is empty before filling FIFO */ + if (!(readl_relaxed(port->membase + ofs->isr) & USART_SR_TXE)) + break; + writel_relaxed(xmit->buf[xmit->tail], port->membase + ofs->tdr); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + } - writel_relaxed(xmit->buf[xmit->tail], port->membase + ofs->tdr); - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); - port->icount.tx++; + /* rely on TXE irq (mask or unmask) for sending remaining data */ + if (uart_circ_empty(xmit)) + stm32_tx_interrupt_disable(port); + else + stm32_tx_interrupt_enable(port); } static void stm32_transmit_chars_dma(struct uart_port *port) @@ -377,7 +403,6 @@ static void stm32_transmit_chars_dma(struct uart_port *port) /* Issue pending DMA TX requests */ dma_async_issue_pending(stm32port->tx_ch); - stm32_clr_bits(port, ofs->isr, USART_SR_TC); stm32_set_bits(port, ofs->cr3, USART_CR3_DMAT); xmit->tail = (xmit->tail + count) & (UART_XMIT_SIZE - 1); @@ -401,15 +426,15 @@ static void stm32_transmit_chars(struct uart_port *port) return; } - if (uart_tx_stopped(port)) { - stm32_stop_tx(port); + if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { + stm32_tx_interrupt_disable(port); return; } - if (uart_circ_empty(xmit)) { - stm32_stop_tx(port); - return; - } + if (ofs->icr == UNDEF_REG) + stm32_clr_bits(port, ofs->isr, USART_SR_TC); + else + stm32_set_bits(port, ofs->icr, USART_ICR_TCCF); if (stm32_port->tx_ch) stm32_transmit_chars_dma(port); @@ -420,7 +445,7 @@ static void stm32_transmit_chars(struct uart_port *port) uart_write_wakeup(port); if (uart_circ_empty(xmit)) - stm32_stop_tx(port); + stm32_tx_interrupt_disable(port); } static irqreturn_t stm32_interrupt(int irq, void *ptr) @@ -434,6 +459,10 @@ static irqreturn_t stm32_interrupt(int irq, void *ptr) sr = readl_relaxed(port->membase + ofs->isr); + if ((sr & USART_SR_RTOF) && ofs->icr != UNDEF_REG) + writel_relaxed(USART_ICR_RTOCF, + port->membase + ofs->icr); + if ((sr & USART_SR_WUF) && (ofs->icr != UNDEF_REG)) writel_relaxed(USART_ICR_WUCF, port->membase + ofs->icr); @@ -495,10 +524,7 @@ static unsigned int stm32_get_mctrl(struct uart_port *port) /* Transmit stop */ static void stm32_stop_tx(struct uart_port *port) { - struct stm32_port *stm32_port = to_stm32_port(port); - struct stm32_usart_offsets *ofs = &stm32_port->info->ofs; - - stm32_clr_bits(port, ofs->cr1, USART_CR1_TXEIE); + stm32_tx_interrupt_disable(port); } /* There are probably characters waiting to be transmitted. */ @@ -520,7 +546,10 @@ static void stm32_throttle(struct uart_port *port) unsigned long flags; spin_lock_irqsave(&port->lock, flags); - stm32_clr_bits(port, ofs->cr1, USART_CR1_RXNEIE); + stm32_clr_bits(port, ofs->cr1, stm32_port->cr1_irq); + if (stm32_port->cr3_irq) + stm32_clr_bits(port, ofs->cr3, stm32_port->cr3_irq); + spin_unlock_irqrestore(&port->lock, flags); } @@ -532,7 +561,10 @@ static void stm32_unthrottle(struct uart_port *port) unsigned long flags; spin_lock_irqsave(&port->lock, flags); - stm32_set_bits(port, ofs->cr1, USART_CR1_RXNEIE); + stm32_set_bits(port, ofs->cr1, stm32_port->cr1_irq); + if (stm32_port->cr3_irq) + stm32_set_bits(port, ofs->cr3, stm32_port->cr3_irq); + spin_unlock_irqrestore(&port->lock, flags); } @@ -542,7 +574,10 @@ static void stm32_stop_rx(struct uart_port *port) struct stm32_port *stm32_port = to_stm32_port(port); struct stm32_usart_offsets *ofs = &stm32_port->info->ofs; - stm32_clr_bits(port, ofs->cr1, USART_CR1_RXNEIE); + stm32_clr_bits(port, ofs->cr1, stm32_port->cr1_irq); + if (stm32_port->cr3_irq) + stm32_clr_bits(port, ofs->cr3, stm32_port->cr3_irq); + } /* Handle breaks - ignored by us */ @@ -554,7 +589,6 @@ static int stm32_startup(struct uart_port *port) { struct stm32_port *stm32_port = to_stm32_port(port); struct stm32_usart_offsets *ofs = &stm32_port->info->ofs; - struct stm32_usart_config *cfg = &stm32_port->info->cfg; const char *name = to_platform_device(port->dev)->name; u32 val; int ret; @@ -565,16 +599,21 @@ static int stm32_startup(struct uart_port *port) if (ret) return ret; - if (cfg->has_wakeup && stm32_port->wakeirq >= 0) { - ret = dev_pm_set_dedicated_wake_irq(port->dev, - stm32_port->wakeirq); - if (ret) { - free_irq(port->irq, port); - return ret; - } + /* RX FIFO Flush */ + if (ofs->rqr != UNDEF_REG) + stm32_set_bits(port, ofs->rqr, USART_RQR_RXFRQ); + + /* Tx and RX FIFO configuration */ + if (stm32_port->fifoen) { + val = readl_relaxed(port->membase + ofs->cr3); + val &= ~(USART_CR3_TXFTCFG_MASK | USART_CR3_RXFTCFG_MASK); + val |= USART_CR3_TXFTCFG_HALF << USART_CR3_TXFTCFG_SHIFT; + val |= USART_CR3_RXFTCFG_HALF << USART_CR3_RXFTCFG_SHIFT; + writel_relaxed(val, port->membase + ofs->cr3); } - val = USART_CR1_RXNEIE | USART_CR1_TE | USART_CR1_RE; + /* RX FIFO enabling */ + val = stm32_port->cr1_irq | USART_CR1_RE; if (stm32_port->fifoen) val |= USART_CR1_FIFOEN; stm32_set_bits(port, ofs->cr1, val); @@ -587,18 +626,57 @@ static void stm32_shutdown(struct uart_port *port) struct stm32_port *stm32_port = to_stm32_port(port); struct stm32_usart_offsets *ofs = &stm32_port->info->ofs; struct stm32_usart_config *cfg = &stm32_port->info->cfg; - u32 val; + u32 val, isr; + int ret; - val = USART_CR1_TXEIE | USART_CR1_RXNEIE | USART_CR1_TE | USART_CR1_RE; + val = USART_CR1_TXEIE | USART_CR1_TE; + val |= stm32_port->cr1_irq | USART_CR1_RE; val |= BIT(cfg->uart_enable_bit); if (stm32_port->fifoen) val |= USART_CR1_FIFOEN; + + ret = readl_relaxed_poll_timeout(port->membase + ofs->isr, + isr, (isr & USART_SR_TC), + 10, 100000); + + if (ret) + dev_err(port->dev, "transmission complete not set\n"); + stm32_clr_bits(port, ofs->cr1, val); - dev_pm_clear_wake_irq(port->dev); free_irq(port->irq, port); } +static unsigned int stm32_get_databits(struct ktermios *termios) +{ + unsigned int bits; + + tcflag_t cflag = termios->c_cflag; + + switch (cflag & CSIZE) { + /* + * CSIZE settings are not necessarily supported in hardware. + * CSIZE unsupported configurations are handled here to set word length + * to 8 bits word as default configuration and to print debug message. + */ + case CS5: + bits = 5; + break; + case CS6: + bits = 6; + break; + case CS7: + bits = 7; + break; + /* default including CS8 */ + default: + bits = 8; + break; + } + + return bits; +} + static void stm32_set_termios(struct uart_port *port, struct ktermios *termios, struct ktermios *old) { @@ -606,7 +684,7 @@ static void stm32_set_termios(struct uart_port *port, struct ktermios *termios, struct stm32_usart_offsets *ofs = &stm32_port->info->ofs; struct stm32_usart_config *cfg = &stm32_port->info->cfg; struct serial_rs485 *rs485conf = &port->rs485; - unsigned int baud; + unsigned int baud, bits; u32 usartdiv, mantissa, fraction, oversampling; tcflag_t cflag = termios->c_cflag; u32 cr1, cr2, cr3; @@ -622,26 +700,64 @@ static void stm32_set_termios(struct uart_port *port, struct ktermios *termios, /* Stop serial port and reset value */ writel_relaxed(0, port->membase + ofs->cr1); - cr1 = USART_CR1_TE | USART_CR1_RE | USART_CR1_RXNEIE; + /* flush RX & TX FIFO */ + if (ofs->rqr != UNDEF_REG) + stm32_set_bits(port, ofs->rqr, + USART_RQR_TXFRQ | USART_RQR_RXFRQ); + cr1 = USART_CR1_TE | USART_CR1_RE; if (stm32_port->fifoen) cr1 |= USART_CR1_FIFOEN; cr2 = 0; - cr3 = 0; + cr3 = readl_relaxed(port->membase + ofs->cr3); + cr3 &= USART_CR3_TXFTIE | USART_CR3_RXFTCFG_MASK | USART_CR3_RXFTIE + | USART_CR3_TXFTCFG_MASK; if (cflag & CSTOPB) cr2 |= USART_CR2_STOP_2B; + bits = stm32_get_databits(termios); + stm32_port->rdr_mask = (BIT(bits) - 1); + if (cflag & PARENB) { + bits++; cr1 |= USART_CR1_PCE; - if ((cflag & CSIZE) == CS8) { - if (cfg->has_7bits_data) - cr1 |= USART_CR1_M0; - else - cr1 |= USART_CR1_M; - } } + /* + * Word length configuration: + * CS8 + parity, 9 bits word aka [M1:M0] = 0b01 + * CS7 or (CS6 + parity), 7 bits word aka [M1:M0] = 0b10 + * CS8 or (CS7 + parity), 8 bits word aka [M1:M0] = 0b00 + * M0 and M1 already cleared by cr1 initialization. + */ + if (bits == 9) + cr1 |= USART_CR1_M0; + else if ((bits == 7) && cfg->has_7bits_data) + cr1 |= USART_CR1_M1; + else if (bits != 8) + dev_dbg(port->dev, "Unsupported data bits config: %u bits\n" + , bits); + + if (ofs->rtor != UNDEF_REG && (stm32_port->rx_ch || + stm32_port->fifoen)) { + if (cflag & CSTOPB) + bits = bits + 3; /* 1 start bit + 2 stop bits */ + else + bits = bits + 2; /* 1 start bit + 1 stop bit */ + + /* RX timeout irq to occur after last stop bit + bits */ + stm32_port->cr1_irq = USART_CR1_RTOIE; + writel_relaxed(bits, port->membase + ofs->rtor); + cr2 |= USART_CR2_RTOEN; + /* Not using dma, enable fifo threshold irq */ + if (!stm32_port->rx_ch) + stm32_port->cr3_irq = USART_CR3_RXFTIE; + } + + cr1 |= stm32_port->cr1_irq; + cr3 |= stm32_port->cr3_irq; + if (cflag & PARODD) cr1 |= USART_CR1_PS; @@ -679,14 +795,14 @@ static void stm32_set_termios(struct uart_port *port, struct ktermios *termios, if (termios->c_iflag & INPCK) port->read_status_mask |= USART_SR_PE | USART_SR_FE; if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) - port->read_status_mask |= USART_SR_LBD; + port->read_status_mask |= USART_SR_FE; /* Characters to ignore */ port->ignore_status_mask = 0; if (termios->c_iflag & IGNPAR) port->ignore_status_mask = USART_SR_PE | USART_SR_FE; if (termios->c_iflag & IGNBRK) { - port->ignore_status_mask |= USART_SR_LBD; + port->ignore_status_mask |= USART_SR_FE; /* * If we're ignoring parity and break indicators, * ignore overruns too (for real raw support). @@ -808,12 +924,32 @@ static int stm32_init_port(struct stm32_port *stm32port, port->flags = UPF_BOOT_AUTOCONF; port->ops = &stm32_uart_ops; port->dev = &pdev->dev; - port->irq = platform_get_irq(pdev, 0); + port->fifosize = stm32port->info->cfg.fifosize; + + ret = platform_get_irq(pdev, 0); + if (ret <= 0) { + if (ret != -EPROBE_DEFER) + dev_err(&pdev->dev, "Can't get event IRQ: %d\n", ret); + return ret ? ret : -ENODEV; + } + port->irq = ret; + port->rs485_config = stm32_config_rs485; stm32_init_rs485(port, pdev); - stm32port->wakeirq = platform_get_irq(pdev, 1); + if (stm32port->info->cfg.has_wakeup) { + stm32port->wakeirq = platform_get_irq(pdev, 1); + if (stm32port->wakeirq <= 0 && stm32port->wakeirq != -ENXIO) { + if (stm32port->wakeirq != -EPROBE_DEFER) + dev_err(&pdev->dev, + "Can't get event wake IRQ: %d\n", + stm32port->wakeirq); + return stm32port->wakeirq ? stm32port->wakeirq : + -ENODEV; + } + } + stm32port->fifoen = stm32port->info->cfg.has_fifo; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -862,6 +998,8 @@ static struct stm32_port *stm32_of_get_stm32_port(struct platform_device *pdev) stm32_ports[id].hw_flow_control = of_property_read_bool(np, "st,hw-flow-ctrl"); stm32_ports[id].port.line = id; + stm32_ports[id].cr1_irq = USART_CR1_RXNEIE; + stm32_ports[id].cr3_irq = 0; stm32_ports[id].last_res = RX_BUF_L; return &stm32_ports[id]; } @@ -1020,15 +1158,22 @@ static int stm32_serial_probe(struct platform_device *pdev) if (ret) return ret; - if (stm32port->info->cfg.has_wakeup && stm32port->wakeirq >= 0) { + if (stm32port->wakeirq > 0) { ret = device_init_wakeup(&pdev->dev, true); if (ret) goto err_uninit; + + ret = dev_pm_set_dedicated_wake_irq(&pdev->dev, + stm32port->wakeirq); + if (ret) + goto err_nowup; + + device_set_wakeup_enable(&pdev->dev, false); } ret = uart_add_one_port(&stm32_usart_driver, &stm32port->port); if (ret) - goto err_nowup; + goto err_wirq; ret = stm32_of_dma_rx_probe(stm32port, pdev); if (ret) @@ -1042,8 +1187,12 @@ static int stm32_serial_probe(struct platform_device *pdev) return 0; +err_wirq: + if (stm32port->wakeirq > 0) + dev_pm_clear_wake_irq(&pdev->dev); + err_nowup: - if (stm32port->info->cfg.has_wakeup && stm32port->wakeirq >= 0) + if (stm32port->wakeirq > 0) device_init_wakeup(&pdev->dev, false); err_uninit: @@ -1057,7 +1206,6 @@ static int stm32_serial_remove(struct platform_device *pdev) struct uart_port *port = platform_get_drvdata(pdev); struct stm32_port *stm32_port = to_stm32_port(port); struct stm32_usart_offsets *ofs = &stm32_port->info->ofs; - struct stm32_usart_config *cfg = &stm32_port->info->cfg; stm32_clr_bits(port, ofs->cr3, USART_CR3_DMAR); @@ -1079,8 +1227,10 @@ static int stm32_serial_remove(struct platform_device *pdev) TX_BUF_L, stm32_port->tx_buf, stm32_port->tx_dma_buf); - if (cfg->has_wakeup && stm32_port->wakeirq >= 0) + if (stm32_port->wakeirq > 0) { + dev_pm_clear_wake_irq(&pdev->dev); device_init_wakeup(&pdev->dev, false); + } clk_disable_unprepare(stm32_port->clk); @@ -1195,7 +1345,7 @@ static void stm32_serial_enable_wakeup(struct uart_port *port, bool enable) struct stm32_usart_config *cfg = &stm32_port->info->cfg; u32 val; - if (!cfg->has_wakeup || stm32_port->wakeirq < 0) + if (stm32_port->wakeirq <= 0) return; if (enable) { diff --git a/drivers/tty/serial/stm32-usart.h b/drivers/tty/serial/stm32-usart.h index 6f294e280ea3..a175c1094dc8 100644 --- a/drivers/tty/serial/stm32-usart.h +++ b/drivers/tty/serial/stm32-usart.h @@ -27,6 +27,7 @@ struct stm32_usart_config { bool has_7bits_data; bool has_wakeup; bool has_fifo; + int fifosize; }; struct stm32_usart_info { @@ -54,6 +55,7 @@ struct stm32_usart_info stm32f4_info = { .cfg = { .uart_enable_bit = 13, .has_7bits_data = false, + .fifosize = 1, } }; @@ -74,6 +76,7 @@ struct stm32_usart_info stm32f7_info = { .cfg = { .uart_enable_bit = 0, .has_7bits_data = true, + .fifosize = 1, } }; @@ -96,6 +99,7 @@ struct stm32_usart_info stm32h7_info = { .has_7bits_data = true, .has_wakeup = true, .has_fifo = true, + .fifosize = 16, } }; @@ -108,7 +112,6 @@ struct stm32_usart_info stm32h7_info = { #define USART_SR_RXNE BIT(5) #define USART_SR_TC BIT(6) #define USART_SR_TXE BIT(7) -#define USART_SR_LBD BIT(8) #define USART_SR_CTSIF BIT(9) #define USART_SR_CTS BIT(10) /* F7 */ #define USART_SR_RTOF BIT(11) /* F7 */ @@ -120,8 +123,7 @@ struct stm32_usart_info stm32h7_info = { #define USART_SR_SBKF BIT(18) /* F7 */ #define USART_SR_WUF BIT(20) /* H7 */ #define USART_SR_TEACK BIT(21) /* F7 */ -#define USART_SR_ERR_MASK (USART_SR_LBD | USART_SR_ORE | \ - USART_SR_FE | USART_SR_PE) +#define USART_SR_ERR_MASK (USART_SR_ORE | USART_SR_FE | USART_SR_PE) /* Dummy bits */ #define USART_SR_DUMMY_RX BIT(16) @@ -151,8 +153,7 @@ struct stm32_usart_info stm32h7_info = { #define USART_CR1_PS BIT(9) #define USART_CR1_PCE BIT(10) #define USART_CR1_WAKE BIT(11) -#define USART_CR1_M BIT(12) -#define USART_CR1_M0 BIT(12) /* F7 */ +#define USART_CR1_M0 BIT(12) /* F7 (CR1_M for F4) */ #define USART_CR1_MME BIT(13) /* F7 */ #define USART_CR1_CMIE BIT(14) /* F7 */ #define USART_CR1_OVER8 BIT(15) @@ -169,8 +170,6 @@ struct stm32_usart_info stm32h7_info = { /* USART_CR2 */ #define USART_CR2_ADD_MASK GENMASK(3, 0) /* F4 */ #define USART_CR2_ADDM7 BIT(4) /* F7 */ -#define USART_CR2_LBDL BIT(5) -#define USART_CR2_LBDIE BIT(6) #define USART_CR2_LBCL BIT(8) #define USART_CR2_CPHA BIT(9) #define USART_CR2_CPOL BIT(10) @@ -209,6 +208,19 @@ struct stm32_usart_info stm32h7_info = { #define USART_CR3_WUS_MASK GENMASK(21, 20) /* H7 */ #define USART_CR3_WUS_START_BIT BIT(21) /* H7 */ #define USART_CR3_WUFIE BIT(22) /* H7 */ +#define USART_CR3_TXFTIE BIT(23) /* H7 */ +#define USART_CR3_TCBGTIE BIT(24) /* H7 */ +#define USART_CR3_RXFTCFG_MASK GENMASK(27, 25) /* H7 */ +#define USART_CR3_RXFTCFG_SHIFT 25 /* H7 */ +#define USART_CR3_RXFTIE BIT(28) /* H7 */ +#define USART_CR3_TXFTCFG_MASK GENMASK(31, 29) /* H7 */ +#define USART_CR3_TXFTCFG_SHIFT 29 /* H7 */ + +/* TX FIFO threashold set to half of its depth */ +#define USART_CR3_TXFTCFG_HALF 0x2 + +/* RX FIFO threashold set to half of its depth */ +#define USART_CR3_RXFTCFG_HALF 0x2 /* USART_GTPR */ #define USART_GTPR_PSC_MASK GENMASK(7, 0) @@ -227,12 +239,10 @@ struct stm32_usart_info stm32h7_info = { /* USART_ICR */ #define USART_ICR_PECF BIT(0) /* F7 */ -#define USART_ICR_FFECF BIT(1) /* F7 */ -#define USART_ICR_NCF BIT(2) /* F7 */ +#define USART_ICR_FECF BIT(1) /* F7 */ #define USART_ICR_ORECF BIT(3) /* F7 */ #define USART_ICR_IDLECF BIT(4) /* F7 */ #define USART_ICR_TCCF BIT(6) /* F7 */ -#define USART_ICR_LBDCF BIT(8) /* F7 */ #define USART_ICR_CTSCF BIT(9) /* F7 */ #define USART_ICR_RTOCF BIT(11) /* F7 */ #define USART_ICR_EOBCF BIT(12) /* F7 */ @@ -256,11 +266,14 @@ struct stm32_port { struct dma_chan *tx_ch; /* dma tx channel */ dma_addr_t tx_dma_buf; /* dma tx buffer bus address */ unsigned char *tx_buf; /* dma tx buffer cpu address */ + u32 cr1_irq; /* USART_CR1_RXNEIE or RTOIE */ + u32 cr3_irq; /* USART_CR3_RXFTIE */ int last_res; bool tx_dma_busy; /* dma tx busy */ bool hw_flow_control; bool fifoen; int wakeirq; + int rdr_mask; /* receive data register mask */ }; static struct stm32_port stm32_ports[STM32_MAX_PORTS]; diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c index 605354fd60b1..f145946f659b 100644 --- a/drivers/tty/serial/xilinx_uartps.c +++ b/drivers/tty/serial/xilinx_uartps.c @@ -26,21 +26,23 @@ #include <linux/of.h> #include <linux/module.h> #include <linux/pm_runtime.h> +#include <linux/iopoll.h> #define CDNS_UART_TTY_NAME "ttyPS" #define CDNS_UART_NAME "xuartps" -#define CDNS_UART_MAJOR 0 /* use dynamic node allocation */ #define CDNS_UART_FIFO_SIZE 64 /* FIFO size */ #define CDNS_UART_REGISTER_SPACE 0x1000 +#define TX_TIMEOUT 500000 /* Rx Trigger level */ static int rx_trigger_level = 56; -module_param(rx_trigger_level, uint, S_IRUGO); +static int uartps_major; +module_param(rx_trigger_level, uint, 0444); MODULE_PARM_DESC(rx_trigger_level, "Rx trigger level, 1-63 bytes"); /* Rx Timeout */ static int rx_timeout = 10; -module_param(rx_timeout, uint, S_IRUGO); +module_param(rx_timeout, uint, 0444); MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255"); /* Register offsets for the UART. */ @@ -199,7 +201,7 @@ struct cdns_platform_data { u32 quirks; }; #define to_cdns_uart(_nb) container_of(_nb, struct cdns_uart, \ - clk_rate_change_nb); + clk_rate_change_nb) /** * cdns_uart_handle_rx - Handle the received bytes along with Rx errors. @@ -312,15 +314,16 @@ static void cdns_uart_handle_tx(void *dev_id) } else { numbytes = port->fifosize; while (numbytes && !uart_circ_empty(&port->state->xmit) && - !(readl(port->membase + CDNS_UART_SR) & CDNS_UART_SR_TXFULL)) { + !(readl(port->membase + CDNS_UART_SR) & + CDNS_UART_SR_TXFULL)) { /* * Get the data from the UART circular buffer * and write it to the cdns_uart's TX_FIFO * register. */ writel( - port->state->xmit.buf[port->state->xmit. - tail], port->membase + CDNS_UART_FIFO); + port->state->xmit.buf[port->state->xmit.tail], + port->membase + CDNS_UART_FIFO); port->icount.tx++; @@ -684,18 +687,21 @@ static void cdns_uart_set_termios(struct uart_port *port, unsigned int cval = 0; unsigned int baud, minbaud, maxbaud; unsigned long flags; - unsigned int ctrl_reg, mode_reg; - - spin_lock_irqsave(&port->lock, flags); + unsigned int ctrl_reg, mode_reg, val; + int err; /* Wait for the transmit FIFO to empty before making changes */ if (!(readl(port->membase + CDNS_UART_CR) & CDNS_UART_CR_TX_DIS)) { - while (!(readl(port->membase + CDNS_UART_SR) & - CDNS_UART_SR_TXEMPTY)) { - cpu_relax(); + err = readl_poll_timeout(port->membase + CDNS_UART_SR, + val, (val & CDNS_UART_SR_TXEMPTY), + 1000, TX_TIMEOUT); + if (err) { + dev_err(port->dev, "timed out waiting for tx empty"); + return; } } + spin_lock_irqsave(&port->lock, flags); /* Disable the TX and RX to set baud rate */ ctrl_reg = readl(port->membase + CDNS_UART_CR); @@ -1073,8 +1079,6 @@ static void cdns_uart_poll_put_char(struct uart_port *port, unsigned char c) cpu_relax(); spin_unlock_irqrestore(&port->lock, flags); - - return; } #endif @@ -1517,7 +1521,7 @@ static int cdns_uart_probe(struct platform_device *pdev) cdns_uart_uart_driver->owner = THIS_MODULE; cdns_uart_uart_driver->driver_name = driver_name; cdns_uart_uart_driver->dev_name = CDNS_UART_TTY_NAME; - cdns_uart_uart_driver->major = CDNS_UART_MAJOR; + cdns_uart_uart_driver->major = uartps_major; cdns_uart_uart_driver->minor = cdns_uart_data->id; cdns_uart_uart_driver->nr = 1; @@ -1546,6 +1550,7 @@ static int cdns_uart_probe(struct platform_device *pdev) goto err_out_id; } + uartps_major = cdns_uart_uart_driver->tty_driver->major; cdns_uart_data->cdns_uart_driver = cdns_uart_uart_driver; /* diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c index 033ac7e6a70d..566728fbaf3c 100644 --- a/drivers/tty/tty_io.c +++ b/drivers/tty/tty_io.c @@ -1837,7 +1837,7 @@ static struct tty_struct *tty_open_current_tty(dev_t device, struct file *filp) static struct tty_driver *tty_lookup_driver(dev_t device, struct file *filp, int *index) { - struct tty_driver *driver; + struct tty_driver *driver = NULL; switch (device) { #ifdef CONFIG_VT @@ -1858,6 +1858,8 @@ static struct tty_driver *tty_lookup_driver(dev_t device, struct file *filp, break; } } + if (driver) + tty_driver_kref_put(driver); return ERR_PTR(-ENODEV); } default: diff --git a/include/linux/mv643xx.h b/include/linux/mv643xx.h index 4471cf96ef69..47e5679b48e1 100644 --- a/include/linux/mv643xx.h +++ b/include/linux/mv643xx.h @@ -918,52 +918,6 @@ extern void mv64340_irq_init(unsigned int base); -/* MPSC Platform Device, Driver Data (Shared register regions) */ -#define MPSC_SHARED_NAME "mpsc_shared" - -#define MPSC_ROUTING_BASE_ORDER 0 -#define MPSC_SDMA_INTR_BASE_ORDER 1 - -#define MPSC_ROUTING_REG_BLOCK_SIZE 0x000c -#define MPSC_SDMA_INTR_REG_BLOCK_SIZE 0x0084 - -struct mpsc_shared_pdata { - u32 mrr_val; - u32 rcrr_val; - u32 tcrr_val; - u32 intr_cause_val; - u32 intr_mask_val; -}; - -/* MPSC Platform Device, Driver Data */ -#define MPSC_CTLR_NAME "mpsc" - -#define MPSC_BASE_ORDER 0 -#define MPSC_SDMA_BASE_ORDER 1 -#define MPSC_BRG_BASE_ORDER 2 - -#define MPSC_REG_BLOCK_SIZE 0x0038 -#define MPSC_SDMA_REG_BLOCK_SIZE 0x0c18 -#define MPSC_BRG_REG_BLOCK_SIZE 0x0008 - -struct mpsc_pdata { - u8 mirror_regs; - u8 cache_mgmt; - u8 max_idle; - int default_baud; - int default_bits; - int default_parity; - int default_flow; - u32 chr_1_val; - u32 chr_2_val; - u32 chr_10_val; - u32 mpcr_val; - u32 bcr_val; - u8 brg_can_tune; - u8 brg_clk_src; - u32 brg_clk_freq; -}; - /* Watchdog Platform Device, Driver Data */ #define MV64x60_WDT_NAME "mv64x60_wdt" diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h index 5e0b59422a68..bb2bc99388ca 100644 --- a/include/linux/serial_8250.h +++ b/include/linux/serial_8250.h @@ -110,6 +110,7 @@ struct uart_8250_port { * if no_console_suspend */ unsigned char probe; + struct mctrl_gpios *gpios; #define UART_PROBE_RSA (1 << 0) /* diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h index 67c4aaaa2308..5642c05e0da0 100644 --- a/include/uapi/linux/serial_core.h +++ b/include/uapi/linux/serial_core.h @@ -129,7 +129,7 @@ /* Motorola i.MX SoC */ #define PORT_IMX 62 -/* Marvell MPSC */ +/* Marvell MPSC (obsolete unused) */ #define PORT_MPSC 63 /* TXX9 type number */ |