diff options
| -rw-r--r-- | Documentation/gpio/driver.txt | 72 |
1 files changed, 12 insertions, 60 deletions
diff --git a/Documentation/gpio/driver.txt b/Documentation/gpio/driver.txt index 9d7985171f07..90d0f6aba7a6 100644 --- a/Documentation/gpio/driver.txt +++ b/Documentation/gpio/driver.txt @@ -93,37 +93,22 @@ GPIO irqchips usually fall in one of two categories: Chained GPIO irqchips typically can NOT set the .can_sleep flag on struct gpio_chip, as everything happens directly in the callbacks. - NOTE: chained IRQ handlers are usually not good for real time. If you - are submitting a new driver or refactoring a driver for real time compliance, - consider using creating a nested/threaded irqchip instead, see below. - -* NESTED THREADED GPIO irqchips: these are traditionally off-chip GPIO - expanders and any other GPIO irqchip residing on the other side of a - sleeping bus. Of course such drivers that need slow bus traffic to read - out IRQ status and similar, traffic which may in turn incur other IRQs to - happen, cannot be handled in a quick IRQ handler with IRQs disabled. - - With the introduction of real time support in the Linux kernel, also other - GPIO irqchips are encouraged to use a nested and threaded IRQ handler. - Doing so makes the interrupts naturally preemptible on a real time - setup, which means the system can easily be configured for real time with - a (usually negligable) performance loss. - - These drivers spawn a thread and then mask the parent IRQ line until the - interrupt is handled by the driver. The hallmark of this driver is to call - something like this in its interrupt handler: +* NESTED THREADED GPIO irqchips: these are off-chip GPIO expanders and any + other GPIO irqchip residing on the other side of a sleeping bus. Of course + such drivers that need slow bus traffic to read out IRQ status and similar, + traffic which may in turn incur other IRQs to happen, cannot be handled + in a quick IRQ handler with IRQs disabled. Instead they need to spawn a + thread and then mask the parent IRQ line until the interrupt is handled + by the driver. The hallmark of this driver is to call something like + this in its interrupt handler: static irqreturn_t tc3589x_gpio_irq(int irq, void *data) ... handle_nested_irq(irq); - OR - generic_handle_irq(irq); - Threaded GPIO irqchips should set the .can_sleep flag on struct gpio_chip - to true if they are e.g. accessing the chip over I2C or SPI, indicating that - this chip may sleep when accessing the GPIOs. irqchips that are just made - threaded to be preemptible and thus real time compliant need not do this: - preemption is not sleeping. + The hallmark of threaded GPIO irqchips is that they set the .can_sleep + flag on struct gpio_chip to true, indicating that this chip may sleep + when accessing the GPIOs. To help out in handling the set-up and management of GPIO irqchips and the associated irqdomain and resource allocation callbacks, the gpiolib has @@ -140,7 +125,7 @@ symbol: gpio_chip from a parent IRQ and passes the struct gpio_chip* as handler data. (Notice handler data, since the irqchip data is likely used by the parent irqchip!) This is for the chained type of chip. This is also used - to set up a threaded/nested irqchip if NULL is passed as handler. + to set up a nested irqchip if NULL is passed as handler. To use the helpers please keep the following in mind: @@ -185,39 +170,6 @@ typically be called in the .startup() and .shutdown() callbacks from the irqchip. -Real-Time compliance for GPIO IRQ chips ---------------------------------------- - -Any provider of irqchips needs to be carefully tailored to support Real Time -preemption. It is desireable that all irqchips in the GPIO subsystem keep this -in mind and does the proper testing to assure they are real time-enabled. The -following is a checklist to follow when preparing a driver for real -time-compliance: - -- Nominally use raw_spinlock_t in the IRQ context path of the IRQ handler as - we do not want these sections to be preempted. - -- Do NOT use chained_irq_enter() or chained_irq_exit() in the IRQ handler, - as we want the hotpath to be preemptible. - -- Instead use nested IRQs and generic handlers such as handle_bad_irq(), - handle_level_irq() and handle_edge_irq(). Consequentally the handler - argument of gpiochip_set_chained_irqchip() should be NULL when using the - gpiolib irqchip helpers. - -- Nominally set all handlers to handle_bad_irq() in the setup call, then - set the handler to handle_level_irq() and/or handle_edge_irq() in the irqchip - .set_type() callback depending on what your controller supports. - -- If you need to use the pm_runtime_get*()/pm_runtime_put*() callbacks in some - of the irqchip callbacks, these should be moved to the .irq_bus_lock() - and .irq_bus_unlock() callbacks respectively, as these are the only - slowpath callbacks on an irqchip. Create the callbacks if need be. - -- Test your driver with the apropriate in-kernel real time test cases for both - level and edge IRQs. - - Requesting self-owned GPIO pins ------------------------------- |