diff options
| -rw-r--r-- | MAINTAINERS | 1 | ||||
| -rw-r--r-- | drivers/tty/serial/Kconfig | 32 | ||||
| -rw-r--r-- | drivers/tty/serial/Makefile | 1 | ||||
| -rw-r--r-- | drivers/tty/serial/liteuart.c | 404 |
4 files changed, 438 insertions, 0 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index 3fde022413f9..0b1f39b3938d 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -10178,6 +10178,7 @@ M: Mateusz Holenko <mholenko@antmicro.com> S: Maintained F: Documentation/devicetree/bindings/*/litex,*.yaml F: drivers/soc/litex/litex_soc_ctrl.c +F: drivers/tty/serial/liteuart.c F: include/linux/litex.h LIVE PATCHING diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 1044fc387691..c3c683968ab3 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -1582,6 +1582,38 @@ config SERIAL_MILBEAUT_USIO_CONSOLE receives all kernel messages and warnings and which allows logins in single user mode). +config SERIAL_LITEUART + tristate "LiteUART serial port support" + depends on HAS_IOMEM + depends on OF || COMPILE_TEST + depends on LITEX + select SERIAL_CORE + help + This driver is for the FPGA-based LiteUART serial controller from LiteX + SoC builder. + + Say 'Y' or 'M' here if you wish to use the LiteUART serial controller. + Otherwise, say 'N'. + +config SERIAL_LITEUART_MAX_PORTS + int "Maximum number of LiteUART ports" + depends on SERIAL_LITEUART + default "1" + help + Set this to the maximum number of serial ports you want the driver + to support. + +config SERIAL_LITEUART_CONSOLE + bool "LiteUART serial port console support" + depends on SERIAL_LITEUART=y + select SERIAL_CORE_CONSOLE + help + Say 'Y' or 'M' here if you wish to use the FPGA-based LiteUART serial + controller from LiteX SoC builder as the system console + (the system console is the device which receives all kernel messages + and warnings and which allows logins in single user mode). + Otherwise, say 'N'. + endmenu config SERIAL_MCTRL_GPIO diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile index caf167f0c10a..ed4be0ebab8d 100644 --- a/drivers/tty/serial/Makefile +++ b/drivers/tty/serial/Makefile @@ -90,6 +90,7 @@ obj-$(CONFIG_SERIAL_OWL) += owl-uart.o obj-$(CONFIG_SERIAL_RDA) += rda-uart.o obj-$(CONFIG_SERIAL_MILBEAUT_USIO) += milbeaut_usio.o obj-$(CONFIG_SERIAL_SIFIVE) += sifive.o +obj-$(CONFIG_SERIAL_LITEUART) += liteuart.o # GPIOLIB helpers for modem control lines obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o diff --git a/drivers/tty/serial/liteuart.c b/drivers/tty/serial/liteuart.c new file mode 100644 index 000000000000..64842f3539e1 --- /dev/null +++ b/drivers/tty/serial/liteuart.c @@ -0,0 +1,404 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * LiteUART serial controller (LiteX) Driver + * + * Copyright (C) 2019-2020 Antmicro <www.antmicro.com> + */ + +#include <linux/console.h> +#include <linux/litex.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_platform.h> +#include <linux/serial.h> +#include <linux/serial_core.h> +#include <linux/slab.h> +#include <linux/timer.h> +#include <linux/tty_flip.h> +#include <linux/xarray.h> + +/* + * CSRs definitions (base address offsets + width) + * + * The definitions below are true for LiteX SoC configured for 8-bit CSR Bus, + * 32-bit aligned. + * + * Supporting other configurations might require new definitions or a more + * generic way of indexing the LiteX CSRs. + * + * For more details on how CSRs are defined and handled in LiteX, see comments + * in the LiteX SoC Driver: drivers/soc/litex/litex_soc_ctrl.c + */ +#define OFF_RXTX 0x00 +#define OFF_TXFULL 0x04 +#define OFF_RXEMPTY 0x08 +#define OFF_EV_STATUS 0x0c +#define OFF_EV_PENDING 0x10 +#define OFF_EV_ENABLE 0x14 + +/* events */ +#define EV_TX 0x1 +#define EV_RX 0x2 + +struct liteuart_port { + struct uart_port port; + struct timer_list timer; + u32 id; +}; + +#define to_liteuart_port(port) container_of(port, struct liteuart_port, port) + +static DEFINE_XARRAY_FLAGS(liteuart_array, XA_FLAGS_ALLOC); + +#ifdef CONFIG_SERIAL_LITEUART_CONSOLE +static struct console liteuart_console; +#endif + +static struct uart_driver liteuart_driver = { + .owner = THIS_MODULE, + .driver_name = "liteuart", + .dev_name = "ttyLXU", + .major = 0, + .minor = 0, + .nr = CONFIG_SERIAL_LITEUART_MAX_PORTS, +#ifdef CONFIG_SERIAL_LITEUART_CONSOLE + .cons = &liteuart_console, +#endif +}; + +static void liteuart_timer(struct timer_list *t) +{ + struct liteuart_port *uart = from_timer(uart, t, timer); + struct uart_port *port = &uart->port; + unsigned char __iomem *membase = port->membase; + unsigned int flg = TTY_NORMAL; + int ch; + unsigned long status; + + while ((status = !litex_read8(membase + OFF_RXEMPTY)) == 1) { + ch = litex_read8(membase + OFF_RXTX); + port->icount.rx++; + + /* necessary for RXEMPTY to refresh its value */ + litex_write8(membase + OFF_EV_PENDING, EV_TX | EV_RX); + + /* no overflow bits in status */ + if (!(uart_handle_sysrq_char(port, ch))) + uart_insert_char(port, status, 0, ch, flg); + + tty_flip_buffer_push(&port->state->port); + } + + mod_timer(&uart->timer, jiffies + uart_poll_timeout(port)); +} + +static void liteuart_putchar(struct uart_port *port, int ch) +{ + while (litex_read8(port->membase + OFF_TXFULL)) + cpu_relax(); + + litex_write8(port->membase + OFF_RXTX, ch); +} + +static unsigned int liteuart_tx_empty(struct uart_port *port) +{ + /* not really tx empty, just checking if tx is not full */ + if (!litex_read8(port->membase + OFF_TXFULL)) + return TIOCSER_TEMT; + + return 0; +} + +static void liteuart_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + /* modem control register is not present in LiteUART */ +} + +static unsigned int liteuart_get_mctrl(struct uart_port *port) +{ + return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; +} + +static void liteuart_stop_tx(struct uart_port *port) +{ +} + +static void liteuart_start_tx(struct uart_port *port) +{ + struct circ_buf *xmit = &port->state->xmit; + unsigned char ch; + + if (unlikely(port->x_char)) { + litex_write8(port->membase + OFF_RXTX, port->x_char); + port->icount.tx++; + port->x_char = 0; + } else if (!uart_circ_empty(xmit)) { + while (xmit->head != xmit->tail) { + ch = xmit->buf[xmit->tail]; + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + liteuart_putchar(port, ch); + } + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); +} + +static void liteuart_stop_rx(struct uart_port *port) +{ + struct liteuart_port *uart = to_liteuart_port(port); + + /* just delete timer */ + del_timer(&uart->timer); +} + +static void liteuart_break_ctl(struct uart_port *port, int break_state) +{ + /* LiteUART doesn't support sending break signal */ +} + +static int liteuart_startup(struct uart_port *port) +{ + struct liteuart_port *uart = to_liteuart_port(port); + + /* disable events */ + litex_write8(port->membase + OFF_EV_ENABLE, 0); + + /* prepare timer for polling */ + timer_setup(&uart->timer, liteuart_timer, 0); + mod_timer(&uart->timer, jiffies + uart_poll_timeout(port)); + + return 0; +} + +static void liteuart_shutdown(struct uart_port *port) +{ +} + +static void liteuart_set_termios(struct uart_port *port, struct ktermios *new, + struct ktermios *old) +{ + unsigned int baud; + unsigned long flags; + + spin_lock_irqsave(&port->lock, flags); + + /* update baudrate */ + baud = uart_get_baud_rate(port, new, old, 0, 460800); + uart_update_timeout(port, new->c_cflag, baud); + + spin_unlock_irqrestore(&port->lock, flags); +} + +static const char *liteuart_type(struct uart_port *port) +{ + return "liteuart"; +} + +static void liteuart_release_port(struct uart_port *port) +{ +} + +static int liteuart_request_port(struct uart_port *port) +{ + return 0; +} + +static void liteuart_config_port(struct uart_port *port, int flags) +{ + /* + * Driver core for serial ports forces a non-zero value for port type. + * Write an arbitrary value here to accommodate the serial core driver, + * as ID part of UAPI is redundant. + */ + port->type = 1; +} + +static int liteuart_verify_port(struct uart_port *port, + struct serial_struct *ser) +{ + if (port->type != PORT_UNKNOWN && ser->type != 1) + return -EINVAL; + + return 0; +} + +static const struct uart_ops liteuart_ops = { + .tx_empty = liteuart_tx_empty, + .set_mctrl = liteuart_set_mctrl, + .get_mctrl = liteuart_get_mctrl, + .stop_tx = liteuart_stop_tx, + .start_tx = liteuart_start_tx, + .stop_rx = liteuart_stop_rx, + .break_ctl = liteuart_break_ctl, + .startup = liteuart_startup, + .shutdown = liteuart_shutdown, + .set_termios = liteuart_set_termios, + .type = liteuart_type, + .release_port = liteuart_release_port, + .request_port = liteuart_request_port, + .config_port = liteuart_config_port, + .verify_port = liteuart_verify_port, +}; + +static int liteuart_probe(struct platform_device *pdev) +{ + struct liteuart_port *uart; + struct uart_port *port; + struct xa_limit limit; + int dev_id, ret; + + /* look for aliases; auto-enumerate for free index if not found */ + dev_id = of_alias_get_id(pdev->dev.of_node, "serial"); + if (dev_id < 0) + limit = XA_LIMIT(0, CONFIG_SERIAL_LITEUART_MAX_PORTS); + else + limit = XA_LIMIT(dev_id, dev_id); + + uart = devm_kzalloc(&pdev->dev, sizeof(struct liteuart_port), GFP_KERNEL); + if (!uart) + return -ENOMEM; + + ret = xa_alloc(&liteuart_array, &dev_id, uart, limit, GFP_KERNEL); + if (ret) + return ret; + + uart->id = dev_id; + port = &uart->port; + + /* get membase */ + port->membase = devm_platform_get_and_ioremap_resource(pdev, 0, NULL); + if (!port->membase) + return -ENXIO; + + /* values not from device tree */ + port->dev = &pdev->dev; + port->iotype = UPIO_MEM; + port->flags = UPF_BOOT_AUTOCONF; + port->ops = &liteuart_ops; + port->regshift = 2; + port->fifosize = 16; + port->iobase = 1; + port->type = PORT_UNKNOWN; + port->line = dev_id; + spin_lock_init(&port->lock); + + return uart_add_one_port(&liteuart_driver, &uart->port); +} + +static int liteuart_remove(struct platform_device *pdev) +{ + struct uart_port *port = platform_get_drvdata(pdev); + struct liteuart_port *uart = to_liteuart_port(port); + + xa_erase(&liteuart_array, uart->id); + + return 0; +} + +static const struct of_device_id liteuart_of_match[] = { + { .compatible = "litex,liteuart" }, + {} +}; +MODULE_DEVICE_TABLE(of, liteuart_of_match); + +static struct platform_driver liteuart_platform_driver = { + .probe = liteuart_probe, + .remove = liteuart_remove, + .driver = { + .name = "liteuart", + .of_match_table = liteuart_of_match, + }, +}; + +#ifdef CONFIG_SERIAL_LITEUART_CONSOLE + +static void liteuart_console_write(struct console *co, const char *s, + unsigned int count) +{ + struct liteuart_port *uart; + struct uart_port *port; + unsigned long flags; + + uart = (struct liteuart_port *)xa_load(&liteuart_array, co->index); + port = &uart->port; + + spin_lock_irqsave(&port->lock, flags); + uart_console_write(port, s, count, liteuart_putchar); + spin_unlock_irqrestore(&port->lock, flags); +} + +static int liteuart_console_setup(struct console *co, char *options) +{ + struct liteuart_port *uart; + struct uart_port *port; + int baud = 115200; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + uart = (struct liteuart_port *)xa_load(&liteuart_array, co->index); + if (!uart) + return -ENODEV; + + port = &uart->port; + if (!port->membase) + return -ENODEV; + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + + return uart_set_options(port, co, baud, parity, bits, flow); +} + +static struct console liteuart_console = { + .name = "liteuart", + .write = liteuart_console_write, + .device = uart_console_device, + .setup = liteuart_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &liteuart_driver, +}; + +static int __init liteuart_console_init(void) +{ + register_console(&liteuart_console); + + return 0; +} +console_initcall(liteuart_console_init); +#endif /* CONFIG_SERIAL_LITEUART_CONSOLE */ + +static int __init liteuart_init(void) +{ + int res; + + res = uart_register_driver(&liteuart_driver); + if (res) + return res; + + res = platform_driver_register(&liteuart_platform_driver); + if (res) { + uart_unregister_driver(&liteuart_driver); + return res; + } + + return 0; +} + +static void __exit liteuart_exit(void) +{ + platform_driver_unregister(&liteuart_platform_driver); + uart_unregister_driver(&liteuart_driver); +} + +module_init(liteuart_init); +module_exit(liteuart_exit); + +MODULE_AUTHOR("Antmicro <www.antmicro.com>"); +MODULE_DESCRIPTION("LiteUART serial driver"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform: liteuart"); |