diff options
94 files changed, 2489 insertions, 1521 deletions
@@ -123,6 +123,7 @@ Mark Brown <broonie@sirena.org.uk> Mark Yao <markyao0591@gmail.com> <mark.yao@rock-chips.com> Martin Kepplinger <martink@posteo.de> <martin.kepplinger@theobroma-systems.com> Martin Kepplinger <martink@posteo.de> <martin.kepplinger@ginzinger.com> +Mathieu Othacehe <m.othacehe@gmail.com> Matthew Wilcox <willy@infradead.org> <matthew.r.wilcox@intel.com> Matthew Wilcox <willy@infradead.org> <matthew@wil.cx> Matthew Wilcox <willy@infradead.org> <mawilcox@linuxonhyperv.com> diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt index a4b056761eaa..d5f68ac78d15 100644 --- a/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt @@ -23,6 +23,20 @@ Required properties: Optional properties: - clock-output-names : Should contain name for output clock. +- rohm,reset-snvs-powered : Transfer BD718x7 to SNVS state at reset. + +The BD718x7 supports two different HW states as reset target states. States +are called as SNVS and READY. At READY state all the PMIC power outputs go +down and OTP is reload. At the SNVS state all other logic and external +devices apart from the SNVS power domain are shut off. Please refer to NXP +i.MX8 documentation for further information regarding SNVS state. When a +reset is done via SNVS state the PMIC OTP data is not reload. This causes +power outputs that have been under SW control to stay down when reset has +switched power state to SNVS. If reset is done via READY state the power +outputs will be returned to HW control by OTP loading. Thus the reset +target state is set to READY by default. If SNVS state is used the boot +crucial regulators must have the regulator-always-on and regulator-boot-on +properties set in regulator node. Example: @@ -43,6 +57,7 @@ Example: #clock-cells = <0>; clocks = <&osc 0>; clock-output-names = "bd71837-32k-out"; + rohm,reset-snvs-powered; regulators { buck1: BUCK1 { @@ -50,8 +65,10 @@ Example: regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + regulator-always-on; regulator-ramp-delay = <1250>; }; + // [...] }; }; diff --git a/Documentation/devicetree/bindings/regulator/fan53555.txt b/Documentation/devicetree/bindings/regulator/fan53555.txt index 54a3f2c80e3a..e7fc045281d1 100644 --- a/Documentation/devicetree/bindings/regulator/fan53555.txt +++ b/Documentation/devicetree/bindings/regulator/fan53555.txt @@ -1,7 +1,8 @@ Binding for Fairchild FAN53555 regulators Required properties: - - compatible: one of "fcs,fan53555", "silergy,syr827", "silergy,syr828" + - compatible: one of "fcs,fan53555", "fcs,fan53526", "silergy,syr827" or + "silergy,syr828" - reg: I2C address Optional properties: diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt deleted file mode 100644 index 0c2a6c8a1536..000000000000 --- a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt +++ /dev/null @@ -1,35 +0,0 @@ -Fixed Voltage regulators - -Required properties: -- compatible: Must be "regulator-fixed"; -- regulator-name: Defined in regulator.txt as optional, but required here. - -Optional properties: -- gpio: gpio to use for enable control -- startup-delay-us: startup time in microseconds -- enable-active-high: Polarity of GPIO is Active high -If this property is missing, the default assumed is Active low. -- gpio-open-drain: GPIO is open drain type. - If this property is missing then default assumption is false. --vin-supply: Input supply name. - -Any property defined as part of the core regulator -binding, defined in regulator.txt, can also be used. -However a fixed voltage regulator is expected to have the -regulator-min-microvolt and regulator-max-microvolt -to be the same. - -Example: - - abc: fixedregulator@0 { - compatible = "regulator-fixed"; - regulator-name = "fixed-supply"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - gpio = <&gpio1 16 0>; - startup-delay-us = <70000>; - enable-active-high; - regulator-boot-on; - gpio-open-drain; - vin-supply = <&parent_reg>; - }; diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml new file mode 100644 index 000000000000..d289c2f7455a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/fixed-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Fixed Voltage regulators + +maintainers: + - Liam Girdwood <lgirdwood@gmail.com> + - Mark Brown <broonie@kernel.org> + +description: + Any property defined as part of the core regulator binding, defined in + regulator.txt, can also be used. However a fixed voltage regulator is + expected to have the regulator-min-microvolt and regulator-max-microvolt + to be the same. + +properties: + compatible: + const: regulator-fixed + + regulator-name: true + + gpio: + description: gpio to use for enable control + maxItems: 1 + + startup-delay-us: + description: startup time in microseconds + $ref: /schemas/types.yaml#/definitions/uint32 + + enable-active-high: + description: + Polarity of GPIO is Active high. If this property is missing, + the default assumed is Active low. + type: boolean + + gpio-open-drain: + description: + GPIO is open drain type. If this property is missing then default + assumption is false. + type: boolean + + vin-supply: + description: Input supply phandle. + $ref: /schemas/types.yaml#/definitions/phandle + +required: + - compatible + - regulator-name + +examples: + - | + reg_1v8: regulator-1v8 { + compatible = "regulator-fixed"; + regulator-name = "1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio1 16 0>; + startup-delay-us = <70000>; + enable-active-high; + regulator-boot-on; + gpio-open-drain; + vin-supply = <&parent_reg>; + }; +... diff --git a/Documentation/devicetree/bindings/regulator/max77650-regulator.txt b/Documentation/devicetree/bindings/regulator/max77650-regulator.txt new file mode 100644 index 000000000000..f1cbe813c30f --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max77650-regulator.txt @@ -0,0 +1,41 @@ +Regulator driver for MAX77650 PMIC from Maxim Integrated. + +This module is part of the MAX77650 MFD device. For more details +see Documentation/devicetree/bindings/mfd/max77650.txt. + +The regulator controller is represented as a sub-node of the PMIC node +on the device tree. + +The device has a single LDO regulator and a SIMO buck-boost regulator with +three independent power rails. + +Required properties: +-------------------- +- compatible: Must be "maxim,max77650-regulator" + +Each rail must be instantiated under the regulators subnode of the top PMIC +node. Up to four regulators can be defined. For standard regulator properties +refer to Documentation/devicetree/bindings/regulator/regulator.txt. + +Available regulator compatible strings are: "ldo", "sbb0", "sbb1", "sbb2". + +Example: +-------- + + regulators { + compatible = "maxim,max77650-regulator"; + + max77650_ldo: regulator@0 { + regulator-compatible = "ldo"; + regulator-name = "max77650-ldo"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <2937500>; + }; + + max77650_sbb0: regulator@1 { + regulator-compatible = "sbb0"; + regulator-name = "max77650-sbb0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1587500>; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index f9be1acf891c..4d3b12b92cb3 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -8,7 +8,7 @@ Optional properties: - fsl,pfuze-support-disable-sw: Boolean, if present disable all unused switch regulators to save power consumption. Attention, ensure that all important regulators (e.g. DDR ref, DDR supply) has set the "regulator-always-on" - property. If not present, the switched regualtors are always on and can't be + property. If not present, the switched regulators are always on and can't be disabled. This binding is a workaround to keep backward compatibility with old dtb's which rely on the fact that the switched regulators are always on and don't mark them explicit as "regulator-always-on". diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd70528-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd70528-regulator.txt new file mode 100644 index 000000000000..698cfc3bc3dd --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/rohm,bd70528-regulator.txt @@ -0,0 +1,68 @@ +ROHM BD70528 Power Management Integrated Circuit regulator bindings + +Required properties: + - regulator-name: should be "buck1", "buck2", "buck3", "ldo1", "ldo2", "ldo3", + "led_ldo1", "led_ldo2" + +List of regulators provided by this controller. BD70528 regulators node +should be sub node of the BD70528 MFD node. See BD70528 MFD bindings at +Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt + +The valid names for BD70528 regulator nodes are: +BUCK1, BUCK2, BUCK3, LDO1, LDO2, LDO3, LED_LDO1, LED_LDO2 + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: +regulators { + buck1: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-ramp-delay = <125>; + }; + buck2: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-ramp-delay = <125>; + }; + buck3: BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-ramp-delay = <250>; + }; + ldo1: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + ldo2: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + ldo3: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3300000>; + }; + led_ldo1: LED_LDO1 { + regulator-name = "led_ldo1"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <300000>; + }; + led_ldo2: LED_LDO2 { + regulator-name = "led_ldo2"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <300000>; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt index 4b98ca26e61a..cbce62c22b60 100644 --- a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt @@ -27,8 +27,38 @@ BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6 LDO1, LDO2, LDO3, LDO4, LDO5, LDO6 Optional properties: +- rohm,dvs-run-voltage : PMIC default "RUN" state voltage in uV. + See below table for bucks which support this. +- rohm,dvs-idle-voltage : PMIC default "IDLE" state voltage in uV. + See below table for bucks which support this. +- rohm,dvs-suspend-voltage : PMIC default "SUSPEND" state voltage in uV. + See below table for bucks which support this. - Any optional property defined in bindings/regulator/regulator.txt +Supported default DVS states: + +BD71837: +buck | dvs-run-voltage | dvs-idle-voltage | dvs-suspend-voltage +----------------------------------------------------------------------------- +1 | supported | supported | supported +---------------------------------------------------------------------------- +2 | supported | supported | not supported +---------------------------------------------------------------------------- +3 | supported | not supported | not supported +---------------------------------------------------------------------------- +4 | supported | not supported | not supported +---------------------------------------------------------------------------- +rest | not supported | not supported | not supported + +BD71847: +buck | dvs-run-voltage | dvs-idle-voltage | dvs-suspend-voltage +----------------------------------------------------------------------------- +1 | supported | supported | supported +---------------------------------------------------------------------------- +2 | supported | supported | not supported +---------------------------------------------------------------------------- +rest | not supported | not supported | not supported + Example: regulators { buck1: BUCK1 { @@ -36,7 +66,11 @@ regulators { regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + regulator-always-on; regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <900000>; + rohm,dvs-idle-voltage = <850000>; + rohm,dvs-suspend-voltage = <800000>; }; buck2: BUCK2 { regulator-name = "buck2"; @@ -45,18 +79,22 @@ regulators { regulator-boot-on; regulator-always-on; regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; }; buck3: BUCK3 { regulator-name = "buck3"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + rohm,dvs-run-voltage = <1000000>; }; buck4: BUCK4 { regulator-name = "buck4"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + rohm,dvs-run-voltage = <1000000>; }; buck5: BUCK5 { regulator-name = "buck5"; diff --git a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt index a3f476240565..6189df71ea98 100644 --- a/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt @@ -23,16 +23,14 @@ Switches are fixed voltage regulators with only enable/disable capability. Optional properties: - st,mask-reset: mask reset for this regulator: the regulator configuration is maintained during pmic reset. -- regulator-pull-down: enable high pull down - if not specified light pull down is used - regulator-over-current-protection: if set, all regulators are switched off in case of over-current detection on this regulator, if not set, the driver only sends an over-current event. -- interrupt-parent: phandle to the parent interrupt controller - interrupts: index of current limit detection interrupt - <regulator>-supply: phandle to the parent supply/regulator node each regulator supply can be described except vref_ddr. +- regulator-active-discharge: can be used on pwr_sw1 and pwr_sw2. Example: regulators { @@ -43,7 +41,6 @@ regulators { vdd_core: buck1 { regulator-name = "vdd_core"; interrupts = <IT_CURLIM_BUCK1 0>; - interrupt-parent = <&pmic>; st,mask-reset; regulator-pull-down; regulator-min-microvolt = <700000>; @@ -53,7 +50,6 @@ regulators { v3v3: buck4 { regulator-name = "v3v3"; interrupts = <IT_CURLIM_BUCK4 0>; - interrupt-parent = <&mypmic>; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; diff --git a/Documentation/devicetree/bindings/regulator/tps65218.txt b/Documentation/devicetree/bindings/regulator/tps65218.txt index 02f0e9bbfbf8..54aded3b78e2 100644 --- a/Documentation/devicetree/bindings/regulator/tps65218.txt +++ b/Documentation/devicetree/bindings/regulator/tps65218.txt @@ -71,8 +71,13 @@ tps65218: tps65218@24 { regulator-always-on; }; + ls2: regulator-ls2 { + regulator-min-microamp = <100000>; + regulator-max-microamp = <1000000>; + }; + ls3: regulator-ls3 { - regulator-min-microvolt = <100000>; - regulator-max-microvolt = <1000000>; + regulator-min-microamp = <100000>; + regulator-max-microamp = <1000000>; }; }; diff --git a/arch/arm/mach-imx/mach-mx21ads.c b/arch/arm/mach-imx/mach-mx21ads.c index 2e1e540f2e5a..d278fb672d40 100644 --- a/arch/arm/mach-imx/mach-mx21ads.c +++ b/arch/arm/mach-imx/mach-mx21ads.c @@ -205,7 +205,6 @@ static struct regulator_init_data mx21ads_lcd_regulator_init_data = { static struct fixed_voltage_config mx21ads_lcd_regulator_pdata = { .supply_name = "LCD", .microvolts = 3300000, - .enable_high = 1, .init_data = &mx21ads_lcd_regulator_init_data, }; diff --git a/arch/arm/mach-imx/mach-mx27ads.c b/arch/arm/mach-imx/mach-mx27ads.c index f5e04047ed13..6dd7f57c332f 100644 --- a/arch/arm/mach-imx/mach-mx27ads.c +++ b/arch/arm/mach-imx/mach-mx27ads.c @@ -237,7 +237,7 @@ static struct fixed_voltage_config mx27ads_lcd_regulator_pdata = { static struct gpiod_lookup_table mx27ads_lcd_regulator_gpiod_table = { .dev_id = "reg-fixed-voltage.0", /* Let's hope ID 0 is what we get */ .table = { - GPIO_LOOKUP("LCD", 0, NULL, GPIO_ACTIVE_HIGH), + GPIO_LOOKUP("LCD", 0, NULL, GPIO_ACTIVE_LOW), { }, }, }; diff --git a/arch/arm/mach-mmp/brownstone.c b/arch/arm/mach-mmp/brownstone.c index a04e249c654b..d2560fb1e835 100644 --- a/arch/arm/mach-mmp/brownstone.c +++ b/arch/arm/mach-mmp/brownstone.c @@ -149,7 +149,6 @@ static struct regulator_init_data brownstone_v_5vp_data = { static struct fixed_voltage_config brownstone_v_5vp = { .supply_name = "v_5vp", .microvolts = 5000000, - .enable_high = 1, .enabled_at_boot = 1, .init_data = &brownstone_v_5vp_data, }; diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c index c4c0a8ea11e4..be30c3c061b4 100644 --- a/arch/arm/mach-omap1/board-ams-delta.c +++ b/arch/arm/mach-omap1/board-ams-delta.c @@ -267,7 +267,6 @@ static struct fixed_voltage_config modem_nreset_config = { .supply_name = "modem_nreset", .microvolts = 3300000, .startup_delay = 25000, - .enable_high = 1, .enabled_at_boot = 1, .init_data = &modem_nreset_data, }; @@ -533,7 +532,6 @@ static struct regulator_init_data keybrd_pwr_initdata = { static struct fixed_voltage_config keybrd_pwr_config = { .supply_name = "keybrd_pwr", .microvolts = 5000000, - .enable_high = 1, .init_data = &keybrd_pwr_initdata, }; diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c index 8a5b6ed4ec36..a2ecc5e69abb 100644 --- a/arch/arm/mach-omap2/pdata-quirks.c +++ b/arch/arm/mach-omap2/pdata-quirks.c @@ -330,7 +330,6 @@ static struct fixed_voltage_config pandora_vwlan = { .supply_name = "vwlan", .microvolts = 1800000, /* 1.8V */ .startup_delay = 50000, /* 50ms */ - .enable_high = 1, .init_data = &pandora_vmmc3, }; diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c index 32c1edeb3f14..5ba7bb7f7d51 100644 --- a/arch/arm/mach-pxa/em-x270.c +++ b/arch/arm/mach-pxa/em-x270.c @@ -976,7 +976,6 @@ static struct fixed_voltage_config camera_dummy_config = { .supply_name = "camera_vdd", .input_supply = "vcc cam", .microvolts = 2800000, - .enable_high = 0, .init_data = &camera_dummy_initdata, }; diff --git a/arch/arm/mach-pxa/ezx.c b/arch/arm/mach-pxa/ezx.c index 565965e9acc7..5e110e70ce5a 100644 --- a/arch/arm/mach-pxa/ezx.c +++ b/arch/arm/mach-pxa/ezx.c @@ -714,7 +714,6 @@ static struct regulator_init_data camera_regulator_initdata = { static struct fixed_voltage_config camera_regulator_config = { .supply_name = "camera_vdd", .microvolts = 2800000, - .enable_high = 0, .init_data = &camera_regulator_initdata, }; @@ -730,7 +729,7 @@ static struct gpiod_lookup_table camera_supply_gpiod_table = { .dev_id = "reg-fixed-voltage.1", .table = { GPIO_LOOKUP("gpio-pxa", GPIO50_nCAM_EN, - NULL, GPIO_ACTIVE_HIGH), + NULL, GPIO_ACTIVE_LOW), { }, }, }; diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c index b79b757fdd41..51d38d5e776a 100644 --- a/arch/arm/mach-pxa/hx4700.c +++ b/arch/arm/mach-pxa/hx4700.c @@ -19,6 +19,7 @@ #include <linux/platform_device.h> #include <linux/delay.h> #include <linux/fb.h> +#include <linux/gpio/machine.h> #include <linux/gpio.h> #include <linux/gpio_keys.h> #include <linux/input.h> @@ -702,9 +703,7 @@ static struct regulator_init_data bq24022_init_data = { .consumer_supplies = bq24022_consumers, }; -static struct gpio bq24022_gpios[] = { - { GPIO96_HX4700_BQ24022_ISET2, GPIOF_OUT_INIT_LOW, "bq24022_iset2" }, -}; +static enum gpiod_flags bq24022_gpiod_gflags[] = { GPIOD_OUT_LOW }; static struct gpio_regulator_state bq24022_states[] = { { .value = 100000, .gpios = (0 << 0) }, @@ -714,12 +713,10 @@ static struct gpio_regulator_state bq24022_states[] = { static struct gpio_regulator_config bq24022_info = { .supply_name = "bq24022", - .enable_gpio = GPIO72_HX4700_BQ24022_nCHARGE_EN, - .enable_high = 0, .enabled_at_boot = 0, - .gpios = bq24022_gpios, - .nr_gpios = ARRAY_SIZE(bq24022_gpios), + .gflags = bq24022_gpiod_gflags, + .ngpios = ARRAY_SIZE(bq24022_gpiod_gflags), .states = bq24022_states, .nr_states = ARRAY_SIZE(bq24022_states), @@ -736,6 +733,17 @@ static struct platform_device bq24022 = { }, }; +static struct gpiod_lookup_table bq24022_gpiod_table = { + .dev_id = "gpio-regulator", + .table = { + GPIO_LOOKUP("gpio-pxa", GPIO96_HX4700_BQ24022_ISET2, + NULL, GPIO_ACTIVE_HIGH), + GPIO_LOOKUP("gpio-pxa", GPIO72_HX4700_BQ24022_nCHARGE_EN, + "enable", GPIO_ACTIVE_LOW), + { }, + }, +}; + /* * StrataFlash */ @@ -878,6 +886,7 @@ static void __init hx4700_init(void) pxa_set_btuart_info(NULL); pxa_set_stuart_info(NULL); + gpiod_add_lookup_table(&bq24022_gpiod_table); platform_add_devices(devices, ARRAY_SIZE(devices)); pwm_add_table(hx4700_pwm_lookup, ARRAY_SIZE(hx4700_pwm_lookup)); diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c index 08b079653c3f..6538a7c0e504 100644 --- a/arch/arm/mach-pxa/magician.c +++ b/arch/arm/mach-pxa/magician.c @@ -645,9 +645,8 @@ static struct regulator_init_data bq24022_init_data = { .consumer_supplies = bq24022_consumers, }; -static struct gpio bq24022_gpios[] = { - { EGPIO_MAGICIAN_BQ24022_ISET2, GPIOF_OUT_INIT_LOW, "bq24022_iset2" }, -}; + +static enum gpiod_flags bq24022_gpiod_gflags[] = { GPIOD_OUT_LOW }; static struct gpio_regulator_state bq24022_states[] = { { .value = 100000, .gpios = (0 << 0) }, @@ -657,12 +656,10 @@ static struct gpio_regulator_state bq24022_states[] = { static struct gpio_regulator_config bq24022_info = { .supply_name = "bq24022", - .enable_gpio = GPIO30_MAGICIAN_BQ24022_nCHARGE_EN, - .enable_high = 0, .enabled_at_boot = 1, - .gpios = bq24022_gpios, - .nr_gpios = ARRAY_SIZE(bq24022_gpios), + .gflags = bq24022_gpiod_gflags, + .ngpios = ARRAY_SIZE(bq24022_gpiod_gflags), .states = bq24022_states, .nr_states = ARRAY_SIZE(bq24022_states), @@ -679,6 +676,17 @@ static struct platform_device bq24022 = { }, }; +static struct gpiod_lookup_table bq24022_gpiod_table = { + .dev_id = "gpio-regulator", + .table = { + GPIO_LOOKUP("gpio-pxa", EGPIO_MAGICIAN_BQ24022_ISET2, + NULL, GPIO_ACTIVE_HIGH), + GPIO_LOOKUP("gpio-pxa", GPIO30_MAGICIAN_BQ24022_nCHARGE_EN, + "enable", GPIO_ACTIVE_LOW), + { }, + }, +}; + /* * fixed regulator for ads7846 */ @@ -1027,6 +1035,7 @@ static void __init magician_init(void) regulator_register_always_on(0, "power", pwm_backlight_supply, ARRAY_SIZE(pwm_backlight_supply), 5000000); + gpiod_add_lookup_table(&bq24022_gpiod_table); platform_add_devices(ARRAY_AND_SIZE(devices)); } diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c index e1db072756f2..e13bfc9b01d2 100644 --- a/arch/arm/mach-pxa/raumfeld.c +++ b/arch/arm/mach-pxa/raumfeld.c @@ -883,7 +883,6 @@ static struct regulator_init_data audio_va_initdata = { static struct fixed_voltage_config audio_va_config = { .supply_name = "audio_va", .microvolts = 5000000, - .enable_high = 1, .enabled_at_boot = 0, .init_data = &audio_va_initdata, }; diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c index c411f79d4cb5..ebd654302387 100644 --- a/arch/arm/mach-pxa/zeus.c +++ b/arch/arm/mach-pxa/zeus.c @@ -426,7 +426,7 @@ static struct gpiod_lookup_table can_regulator_gpiod_table = { .dev_id = "reg-fixed-voltage.0", .table = { GPIO_LOOKUP("gpio-pxa", ZEUS_CAN_SHDN_GPIO, - NULL, GPIO_ACTIVE_HIGH), + NULL, GPIO_ACTIVE_LOW), { }, }, }; @@ -547,7 +547,6 @@ static struct regulator_init_data zeus_ohci_regulator_data = { static struct fixed_voltage_config zeus_ohci_regulator_config = { .supply_name = "vbus2", .microvolts = 5000000, /* 5.0V */ - .enable_high = 1, .startup_delay = 0, .init_data = &zeus_ohci_regulator_data, }; diff --git a/arch/arm/mach-sa1100/assabet.c b/arch/arm/mach-sa1100/assabet.c index dfa42496ec27..d09c3f236186 100644 --- a/arch/arm/mach-sa1100/assabet.c +++ b/arch/arm/mach-sa1100/assabet.c @@ -469,7 +469,6 @@ static struct regulator_consumer_supply assabet_cf_vcc_consumers[] = { static struct fixed_voltage_config assabet_cf_vcc_pdata __initdata = { .supply_name = "cf-power", .microvolts = 3300000, - .enable_high = 1, }; static struct gpiod_lookup_table assabet_cf_vcc_gpio_table = { diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c index 22b4106b8084..5495efa07335 100644 --- a/arch/sh/boards/mach-ecovec24/setup.c +++ b/arch/sh/boards/mach-ecovec24/setup.c @@ -630,7 +630,6 @@ static struct regulator_init_data cn12_power_init_data = { static struct fixed_voltage_config cn12_power_info = { .supply_name = "CN12 SD/MMC Vdd", .microvolts = 3300000, - .enable_high = 1, .init_data = &cn12_power_init_data, }; @@ -671,7 +670,6 @@ static struct regulator_init_data sdhi0_power_init_data = { static struct fixed_voltage_config sdhi0_power_info = { .supply_name = "CN11 SD/MMC Vdd", .microvolts = 3300000, - .enable_high = 1, .init_data = &sdhi0_power_init_data, }; diff --git a/arch/x86/platform/intel-mid/device_libs/platform_bcm43xx.c b/arch/x86/platform/intel-mid/device_libs/platform_bcm43xx.c index 96f438d4b026..1421d5330b2c 100644 --- a/arch/x86/platform/intel-mid/device_libs/platform_bcm43xx.c +++ b/arch/x86/platform/intel-mid/device_libs/platform_bcm43xx.c @@ -44,7 +44,6 @@ static struct fixed_voltage_config bcm43xx_vmmc = { */ .microvolts = 2000000, /* 1.8V */ .startup_delay = 250 * 1000, /* 250ms */ - .enable_high = 1, /* active high */ .enabled_at_boot = 0, /* disabled at boot */ .init_data = &bcm43xx_vmmc_data, }; diff --git a/drivers/regulator/88pm8607.c b/drivers/regulator/88pm8607.c index 28f55248eb90..753a6a1b30c3 100644 --- a/drivers/regulator/88pm8607.c +++ b/drivers/regulator/88pm8607.c @@ -11,7 +11,6 @@ #include <linux/kernel.h> #include <linux/init.h> #include <linux/err.h> -#include <linux/i2c.h> #include <linux/of.h> #include <linux/regulator/of_regulator.h> #include <linux/platform_device.h> @@ -22,12 +21,7 @@ struct pm8607_regulator_info { struct regulator_desc desc; - struct pm860x_chip *chip; - struct regulator_dev *regulator; - struct i2c_client *i2c; - struct i2c_client *i2c_8606; - unsigned int *vol_table; unsigned int *vol_suspend; int slope_double; @@ -210,13 +204,15 @@ static const unsigned int LDO14_suspend_table[] = { static int pm8607_list_voltage(struct regulator_dev *rdev, unsigned index) { struct pm8607_regulator_info *info = rdev_get_drvdata(rdev); - int ret = -EINVAL; + int ret; + + ret = regulator_list_voltage_table(rdev, index); + if (ret < 0) + return ret; + + if (info->slope_double) + ret <<= 1; - if (info->vol_table && (index < rdev->desc->n_voltages)) { - ret = info->vol_table[index]; - if (info->slope_double) - ret <<= 1; - } return ret; } @@ -257,6 +253,7 @@ static const struct regulator_ops pm8606_preg_ops = { .type = REGULATOR_VOLTAGE, \ .id = PM8607_ID_##vreg, \ .owner = THIS_MODULE, \ + .volt_table = vreg##_table, \ .n_voltages = ARRAY_SIZE(vreg##_table), \ .vsel_reg = PM8607_##vreg, \ .vsel_mask = ARRAY_SIZE(vreg##_table) - 1, \ @@ -266,7 +263,6 @@ static const struct regulator_ops pm8606_preg_ops = { .enable_mask = 1 << (ebit), \ }, \ .slope_double = (0), \ - .vol_table = (unsigned int *)&vreg##_table, \ .vol_suspend = (unsigned int *)&vreg##_suspend_table, \ } @@ -278,6 +274,7 @@ static const struct regulator_ops pm8606_preg_ops = { .type = REGULATOR_VOLTAGE, \ .id = PM8607_ID_LDO##_id, \ .owner = THIS_MODULE, \ + .volt_table = LDO##_id##_table, \ .n_voltages = ARRAY_SIZE(LDO##_id##_table), \ .vsel_reg = PM8607_##vreg, \ .vsel_mask = (ARRAY_SIZE(LDO##_id##_table) - 1) << (shift), \ @@ -285,7 +282,6 @@ static const struct regulator_ops pm8606_preg_ops = { .enable_mask = 1 << (ebit), \ }, \ .slope_double = (0), \ - .vol_table = (unsigned int *)&LDO##_id##_table, \ .vol_suspend = (unsigned int *)&LDO##_id##_suspend_table, \ } @@ -349,6 +345,7 @@ static int pm8607_regulator_probe(struct platform_device *pdev) struct pm8607_regulator_info *info = NULL; struct regulator_init_data *pdata = dev_get_platdata(&pdev->dev); struct regulator_config config = { }; + struct regulator_dev *rdev; struct resource *res; int i; @@ -371,13 +368,9 @@ static int pm8607_regulator_probe(struct platform_device *pdev) /* i is used to check regulator ID */ i = -1; } - info->i2c = (chip->id == CHIP_PM8607) ? chip->client : chip->companion; - info->i2c_8606 = (chip->id == CHIP_PM8607) ? chip->companion : - chip->client; - info->chip = chip; /* check DVC ramp slope double */ - if ((i == PM8607_ID_BUCK3) && info->chip->buck3_double) + if ((i == PM8607_ID_BUCK3) && chip->buck3_double) info->slope_double = 1; config.dev = &pdev->dev; @@ -392,12 +385,11 @@ static int pm8607_regulator_probe(struct platform_device *pdev) else config.regmap = chip->regmap_companion; - info->regulator = devm_regulator_register(&pdev->dev, &info->desc, - &config); - if (IS_ERR(info->regulator)) { + rdev = devm_regulator_register(&pdev->dev, &info->desc, &config); + if (IS_ERR(rdev)) { dev_err(&pdev->dev, "failed to register regulator %s\n", info->desc.name); - return PTR_ERR(info->regulator); + return PTR_ERR(rdev); } platform_set_drvdata(pdev, info); diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig index ee60a222f5eb..b7f249ee5e68 100644 --- a/drivers/regulator/Kconfig +++ b/drivers/regulator/Kconfig @@ -180,6 +180,17 @@ config REGULATOR_BCM590XX BCM590xx PMUs. This will enable support for the software controllable LDO/Switching regulators. +config REGULATOR_BD70528 + tristate "ROHM BD70528 Power Regulator" + depends on MFD_ROHM_BD70528 + help + This driver supports voltage regulators on ROHM BD70528 PMIC. + This will enable support for the software controllable buck + and LDO regulators. + + This driver can also be built as a module. If so, the module + will be called bd70528-regulator. + config REGULATOR_BD718XX tristate "ROHM BD71837 Power Regulator" depends on MFD_ROHM_BD718XX @@ -457,6 +468,14 @@ config REGULATOR_MAX77620 chip to control Step-Down DC-DC and LDOs. Say Y here to enable the regulator driver. +config REGULATOR_MAX77650 + tristate "Maxim MAX77650/77651 regulator support" + depends on MFD_MAX77650 + help + Regulator driver for MAX77650/77651 PMIC from Maxim + Semiconductor. This device has a SIMO with three independent + power rails and an LDO. + config REGULATOR_MAX8649 tristate "Maxim 8649 voltage regulator" depends on I2C @@ -484,7 +503,7 @@ config REGULATOR_MAX8925 tristate "Maxim MAX8925 Power Management IC" depends on MFD_MAX8925 help - Say y here to support the voltage regulaltor of Maxim MAX8925 PMIC. + Say y here to support the voltage regulator of Maxim MAX8925 PMIC. config REGULATOR_MAX8952 tristate "Maxim MAX8952 Power Management IC" @@ -501,7 +520,7 @@ config REGULATOR_MAX8973 select REGMAP_I2C help The MAXIM MAX8973 high-efficiency. three phase, DC-DC step-down - switching regulator delievers up to 9A of output current. Each + switching regulator delivers up to 9A of output current. Each phase operates at a 2MHz fixed frequency with a 120 deg shift from the adjacent phase, allowing the use of small magnetic component. @@ -646,7 +665,7 @@ config REGULATOR_PCF50633 tristate "NXP PCF50633 regulator driver" depends on MFD_PCF50633 help - Say Y here to support the voltage regulators and convertors + Say Y here to support the voltage regulators and converters on PCF50633 config REGULATOR_PFUZE100 @@ -924,7 +943,7 @@ config REGULATOR_TPS65132 select REGMAP_I2C help This driver supports TPS65132 single inductor - dual output - power supply specifcally designed for display panels. + power supply specifically designed for display panels. config REGULATOR_TPS65217 tristate "TI TPS65217 Power regulators" diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile index b12e1c9b2118..1169f8a27d91 100644 --- a/drivers/regulator/Makefile +++ b/drivers/regulator/Makefile @@ -27,6 +27,7 @@ obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o +obj-$(CONFIG_REGULATOR_BD70528) += bd70528-regulator.o obj-$(CONFIG_REGULATOR_BD718XX) += bd718x7-regulator.o obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o obj-$(CONFIG_REGULATOR_DA903X) += da903x.o @@ -60,6 +61,7 @@ obj-$(CONFIG_REGULATOR_LTC3676) += ltc3676.o obj-$(CONFIG_REGULATOR_MAX14577) += max14577-regulator.o obj-$(CONFIG_REGULATOR_MAX1586) += max1586.o obj-$(CONFIG_REGULATOR_MAX77620) += max77620-regulator.o +obj-$(CONFIG_REGULATOR_MAX77650) += max77650-regulator.o obj-$(CONFIG_REGULATOR_MAX8649) += max8649.o obj-$(CONFIG_REGULATOR_MAX8660) += max8660.o obj-$(CONFIG_REGULATOR_MAX8907) += max8907-regulator.o diff --git a/drivers/regulator/act8865-regulator.c b/drivers/regulator/act8865-regulator.c index 21e20483bd91..e0239cf3f56d 100644 --- a/drivers/regulator/act8865-regulator.c +++ b/drivers/regulator/act8865-regulator.c @@ -131,7 +131,7 @@ * ACT8865 voltage number */ #define ACT8865_VOLTAGE_NUM 64 -#define ACT8600_SUDCDC_VOLTAGE_NUM 255 +#define ACT8600_SUDCDC_VOLTAGE_NUM 256 struct act8865 { struct regmap *regmap; @@ -222,7 +222,8 @@ static const struct regulator_linear_range act8600_sudcdc_voltage_ranges[] = { REGULATOR_LINEAR_RANGE(3000000, 0, 63, 0), REGULATOR_LINEAR_RANGE(3000000, 64, 159, 100000), REGULATOR_LINEAR_RANGE(12600000, 160, 191, 200000), - REGULATOR_LINEAR_RANGE(19000000, 191, 255, 400000), + REGULATOR_LINEAR_RANGE(19000000, 192, 247, 400000), + REGULATOR_LINEAR_RANGE(41400000, 248, 255, 0), }; static struct regulator_ops act8865_ops = { diff --git a/drivers/regulator/act8945a-regulator.c b/drivers/regulator/act8945a-regulator.c index 603db77723b6..caa61d306a69 100644 --- a/drivers/regulator/act8945a-regulator.c +++ b/drivers/regulator/act8945a-regulator.c @@ -87,7 +87,8 @@ static const struct regulator_linear_range act8945a_voltage_ranges[] = { static int act8945a_set_suspend_state(struct regulator_dev *rdev, bool enable) { struct regmap *regmap = rdev->regmap; - int id = rdev->desc->id, reg, val; + int id = rdev_get_id(rdev); + int reg, val; switch (id) { case ACT8945A_ID_DCDC1: @@ -159,7 +160,7 @@ static int act8945a_set_mode(struct regulator_dev *rdev, unsigned int mode) { struct act8945a_pmic *act8945a = rdev_get_drvdata(rdev); struct regmap *regmap = rdev->regmap; - int id = rdev->desc->id; + int id = rdev_get_id(rdev); int reg, ret, val = 0; switch (id) { @@ -190,11 +191,11 @@ static int act8945a_set_mode(struct regulator_dev *rdev, unsigned int mode) switch (mode) { case REGULATOR_MODE_STANDBY: - if (rdev->desc->id > ACT8945A_ID_DCDC3) + if (id > ACT8945A_ID_DCDC3) val = BIT(5); break; case REGULATOR_MODE_NORMAL: - if (rdev->desc->id <= ACT8945A_ID_DCDC3) + if (id <= ACT8945A_ID_DCDC3) val = BIT(5); break; default: @@ -213,7 +214,7 @@ static int act8945a_set_mode(struct regulator_dev *rdev, unsigned int mode) static unsigned int act8945a_get_mode(struct regulator_dev *rdev) { struct act8945a_pmic *act8945a = rdev_get_drvdata(rdev); - int id = rdev->desc->id; + int id = rdev_get_id(rdev); if (id < ACT8945A_ID_DCDC1 || id >= ACT8945A_ID_MAX) return -EINVAL; diff --git a/drivers/regulator/arizona-ldo1.c b/drivers/regulator/arizona-ldo1.c index b9a93049e41e..bf3ab405eed1 100644 --- a/drivers/regulator/arizona-ldo1.c +++ b/drivers/regulator/arizona-ldo1.c @@ -40,35 +40,10 @@ struct arizona_ldo1 { struct gpio_desc *ena_gpiod; }; -static int arizona_ldo1_hc_list_voltage(struct regulator_dev *rdev, - unsigned int selector) -{ - if (selector >= rdev->desc->n_voltages) - return -EINVAL; - - if (selector == rdev->desc->n_voltages - 1) - return 1800000; - else - return rdev->desc->min_uV + (rdev->desc->uV_step * selector); -} - -static int arizona_ldo1_hc_map_voltage(struct regulator_dev *rdev, - int min_uV, int max_uV) -{ - int sel; - - sel = DIV_ROUND_UP(min_uV - rdev->desc->min_uV, rdev->desc->uV_step); - if (sel >= rdev->desc->n_voltages) - sel = rdev->desc->n_voltages - 1; - - return sel; -} - static int arizona_ldo1_hc_set_voltage_sel(struct regulator_dev *rdev, unsigned sel) { - struct arizona_ldo1 *ldo = rdev_get_drvdata(rdev); - struct regmap *regmap = ldo->regmap; + struct regmap *regmap = rdev_get_regmap(rdev); unsigned int val; int ret; @@ -85,16 +60,12 @@ static int arizona_ldo1_hc_set_voltage_sel(struct regulator_dev *rdev, if (val) return 0; - val = sel << ARIZONA_LDO1_VSEL_SHIFT; - - return regmap_update_bits(regmap, ARIZONA_LDO1_CONTROL_1, - ARIZONA_LDO1_VSEL_MASK, val); + return regulator_set_voltage_sel_regmap(rdev, sel); } static int arizona_ldo1_hc_get_voltage_sel(struct regulator_dev *rdev) { - struct arizona_ldo1 *ldo = rdev_get_drvdata(rdev); - struct regmap *regmap = ldo->regmap; + struct regmap *regmap = rdev_get_regmap(rdev); unsigned int val; int ret; @@ -105,32 +76,35 @@ static int arizona_ldo1_hc_get_voltage_sel(struct regulator_dev *rdev) if (val & ARIZONA_LDO1_HI_PWR) return rdev->desc->n_voltages - 1; - ret = regmap_read(regmap, ARIZONA_LDO1_CONTROL_1, &val); - if (ret != 0) - return ret; - - return (val & ARIZONA_LDO1_VSEL_MASK) >> ARIZONA_LDO1_VSEL_SHIFT; + return regulator_get_voltage_sel_regmap(rdev); } static const struct regulator_ops arizona_ldo1_hc_ops = { - .list_voltage = arizona_ldo1_hc_list_voltage, - .map_voltage = arizona_ldo1_hc_map_voltage, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, .get_voltage_sel = arizona_ldo1_hc_get_voltage_sel, .set_voltage_sel = arizona_ldo1_hc_set_voltage_sel, .get_bypass = regulator_get_bypass_regmap, .set_bypass = regulator_set_bypass_regmap, }; +static const struct regulator_linear_range arizona_ldo1_hc_ranges[] = { + REGULATOR_LINEAR_RANGE(900000, 0, 0x6, 50000), + REGULATOR_LINEAR_RANGE(1800000, 0x7, 0x7, 0), +}; + static const struct regulator_desc arizona_ldo1_hc = { .name = "LDO1", .supply_name = "LDOVDD", .type = REGULATOR_VOLTAGE, .ops = &arizona_ldo1_hc_ops, + .vsel_reg = ARIZONA_LDO1_CONTROL_1, + .vsel_mask = ARIZONA_LDO1_VSEL_MASK, .bypass_reg = ARIZONA_LDO1_CONTROL_1, .bypass_mask = ARIZONA_LDO1_BYPASS, - .min_uV = 900000, - .uV_step = 50000, + .linear_ranges = arizona_ldo1_hc_ranges, + .n_linear_ranges = ARRAY_SIZE(arizona_ldo1_hc_ranges), .n_voltages = 8, .enable_time = 1500, .ramp_delay = 24000, diff --git a/drivers/regulator/as3722-regulator.c b/drivers/regulator/as3722-regulator.c index 66337e12719b..e5fed289b52d 100644 --- a/drivers/regulator/as3722-regulator.c +++ b/drivers/regulator/as3722-regulator.c @@ -886,7 +886,7 @@ static int as3722_regulator_probe(struct platform_device *pdev) as3722_regs->desc[id].min_uV = 410000; } else { as3722_regs->desc[id].n_voltages = - AS3722_SD0_VSEL_MAX + 1, + AS3722_SD0_VSEL_MAX + 1; as3722_regs->desc[id].min_uV = 610000; } as3722_regs->desc[id].uV_step = 10000; diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c index 48af859fd053..fba8f58ab769 100644 --- a/drivers/regulator/axp20x-regulator.c +++ b/drivers/regulator/axp20x-regulator.c @@ -367,13 +367,12 @@ static const int axp209_dcdc2_ldo3_slew_rates[] = { static int axp20x_set_ramp_delay(struct regulator_dev *rdev, int ramp) { struct axp20x_dev *axp20x = rdev_get_drvdata(rdev); - const struct regulator_desc *desc = rdev->desc; + const struct regulator_desc *desc; u8 reg, mask, enable, cfg = 0xff; const int *slew_rates; int rate_count = 0; - if (!rdev) - return -EINVAL; + desc = rdev->desc; switch (axp20x->variant) { case AXP209_ID: @@ -436,11 +435,13 @@ static int axp20x_set_ramp_delay(struct regulator_dev *rdev, int ramp) static int axp20x_regulator_enable_regmap(struct regulator_dev *rdev) { struct axp20x_dev *axp20x = rdev_get_drvdata(rdev); - const struct regulator_desc *desc = rdev->desc; + const struct regulator_desc *desc; if (!rdev) return -EINVAL; + desc = rdev->desc; + switch (axp20x->variant) { case AXP209_ID: if ((desc->id == AXP20X_LDO3) && @@ -573,7 +574,7 @@ static const struct regulator_desc axp22x_regulators[] = { AXP22X_DCDC3_V_OUT, AXP22X_DCDC3_V_OUT_MASK, AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DCDC3_MASK), AXP_DESC(AXP22X, DCDC4, "dcdc4", "vin4", 600, 1540, 20, - AXP22X_DCDC4_V_OUT, AXP22X_DCDC4_V_OUT, + AXP22X_DCDC4_V_OUT, AXP22X_DCDC4_V_OUT_MASK, AXP22X_PWR_OUT_CTRL1, AXP22X_PWR_OUT_DCDC4_MASK), AXP_DESC(AXP22X, DCDC5, "dcdc5", "vin5", 1000, 2550, 50, AXP22X_DCDC5_V_OUT, AXP22X_DCDC5_V_OUT_MASK, @@ -719,7 +720,7 @@ static const struct regulator_desc axp803_regulators[] = { AXP22X_ALDO1_V_OUT, AXP22X_ALDO1_V_OUT_MASK, AXP22X_PWR_OUT_CTRL3, AXP806_PWR_OUT_ALDO1_MASK), AXP_DESC(AXP803, ALDO2, "aldo2", "aldoin", 700, 3300, 100, - AXP22X_ALDO2_V_OUT, AXP22X_ALDO2_V_OUT, + AXP22X_ALDO2_V_OUT, AXP22X_ALDO2_V_OUT_MASK, AXP22X_PWR_OUT_CTRL3, AXP806_PWR_OUT_ALDO2_MASK), AXP_DESC(AXP803, ALDO3, "aldo3", "aldoin", 700, 3300, 100, AXP22X_ALDO3_V_OUT, AXP22X_ALDO3_V_OUT_MASK, @@ -729,7 +730,7 @@ static const struct regulator_desc axp803_regulators[] = { AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO1_MASK), AXP_DESC_RANGES(AXP803, DLDO2, "dldo2", "dldoin", axp803_dldo2_ranges, AXP803_DLDO2_NUM_VOLTAGES, - AXP22X_DLDO2_V_OUT, AXP22X_DLDO2_V_OUT, + AXP22X_DLDO2_V_OUT, AXP22X_DLDO2_V_OUT_MASK, AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO2_MASK), AXP_DESC(AXP803, DLDO3, "dldo3", "dldoin", 700, 3300, 100, AXP22X_DLDO3_V_OUT, AXP22X_DLDO3_V_OUT_MASK, @@ -744,7 +745,7 @@ static const struct regulator_desc axp803_regulators[] = { AXP22X_ELDO2_V_OUT, AXP22X_ELDO2_V_OUT_MASK, AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO2_MASK), AXP_DESC(AXP803, ELDO3, "eldo3", "eldoin", 700, 1900, 50, - AXP22X_ELDO3_V_OUT, AXP22X_ELDO3_V_OUT, + AXP22X_ELDO3_V_OUT, AXP22X_ELDO3_V_OUT_MASK, AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO3_MASK), AXP_DESC(AXP803, FLDO1, "fldo1", "fldoin", 700, 1450, 50, AXP803_FLDO1_V_OUT, AXP803_FLDO1_V_OUT_MASK, @@ -791,7 +792,7 @@ static const struct regulator_desc axp806_regulators[] = { AXP806_DCDCA_V_CTRL, AXP806_DCDCA_V_CTRL_MASK, AXP806_PWR_OUT_CTRL1, AXP806_PWR_OUT_DCDCA_MASK), AXP_DESC(AXP806, DCDCB, "dcdcb", "vinb", 1000, 2550, 50, - AXP806_DCDCB_V_CTRL, AXP806_DCDCB_V_CTRL, + AXP806_DCDCB_V_CTRL, AXP806_DCDCB_V_CTRL_MASK, AXP806_PWR_OUT_CTRL1, AXP806_PWR_OUT_DCDCB_MASK), AXP_DESC_RANGES(AXP806, DCDCC, "dcdcc", "vinc", axp806_dcdca_ranges, AXP806_DCDCA_NUM_VOLTAGES, @@ -817,7 +818,7 @@ static const struct regulator_desc axp806_regulators[] = { AXP806_BLDO1_V_CTRL, AXP806_BLDO1_V_CTRL_MASK, AXP806_PWR_OUT_CTRL2, AXP806_PWR_OUT_BLDO1_MASK), AXP_DESC(AXP806, BLDO2, "bldo2", "bldoin", 700, 1900, 100, - AXP806_BLDO2_V_CTRL, AXP806_BLDO2_V_CTRL, + AXP806_BLDO2_V_CTRL, AXP806_BLDO2_V_CTRL_MASK, AXP806_PWR_OUT_CTRL2, AXP806_PWR_OUT_BLDO2_MASK), AXP_DESC(AXP806, BLDO3, "bldo3", "bldoin", 700, 1900, 100, AXP806_BLDO3_V_CTRL, AXP806_BLDO3_V_CTRL_MASK, @@ -952,7 +953,7 @@ static const struct regulator_desc axp813_regulators[] = { AXP22X_ALDO1_V_OUT, AXP22X_ALDO1_V_OUT_MASK, AXP22X_PWR_OUT_CTRL3, AXP806_PWR_OUT_ALDO1_MASK), AXP_DESC(AXP813, ALDO2, "aldo2", "aldoin", 700, 3300, 100, - AXP22X_ALDO2_V_OUT, AXP22X_ALDO2_V_OUT, + AXP22X_ALDO2_V_OUT, AXP22X_ALDO2_V_OUT_MASK, AXP22X_PWR_OUT_CTRL3, AXP806_PWR_OUT_ALDO2_MASK), AXP_DESC(AXP813, ALDO3, "aldo3", "aldoin", 700, 3300, 100, AXP22X_ALDO3_V_OUT, AXP22X_ALDO3_V_OUT_MASK, @@ -962,7 +963,7 @@ static const struct regulator_desc axp813_regulators[] = { AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO1_MASK), AXP_DESC_RANGES(AXP813, DLDO2, "dldo2", "dldoin", axp803_dldo2_ranges, AXP803_DLDO2_NUM_VOLTAGES, - AXP22X_DLDO2_V_OUT, AXP22X_DLDO2_V_OUT, + AXP22X_DLDO2_V_OUT, AXP22X_DLDO2_V_OUT_MASK, AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_DLDO2_MASK), AXP_DESC(AXP813, DLDO3, "dldo3", "dldoin", 700, 3300, 100, AXP22X_DLDO3_V_OUT, AXP22X_DLDO3_V_OUT_MASK, @@ -977,7 +978,7 @@ static const struct regulator_desc axp813_regulators[] = { AXP22X_ELDO2_V_OUT, AXP22X_ELDO2_V_OUT_MASK, AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO2_MASK), AXP_DESC(AXP813, ELDO3, "eldo3", "eldoin", 700, 1900, 50, - AXP22X_ELDO3_V_OUT, AXP22X_ELDO3_V_OUT, + AXP22X_ELDO3_V_OUT, AXP22X_ELDO3_V_OUT_MASK, AXP22X_PWR_OUT_CTRL2, AXP22X_PWR_OUT_ELDO3_MASK), /* to do / check ... */ AXP_DESC(AXP813, FLDO1, "fldo1", "fldoin", 700, 1450, 50, diff --git a/drivers/regulator/bcm590xx-regulator.c b/drivers/regulator/bcm590xx-regulator.c index 92d6d7b10cf7..e49c0a7d5dd5 100644 --- a/drivers/regulator/bcm590xx-regulator.c +++ b/drivers/regulator/bcm590xx-regulator.c @@ -242,8 +242,12 @@ static int bcm590xx_get_enable_register(int id) case BCM590XX_REG_SDSR2: reg = BCM590XX_SDSR2PMCTRL1; break; + case BCM590XX_REG_VSR: + reg = BCM590XX_VSRPMCTRL1; + break; case BCM590XX_REG_VBUS: reg = BCM590XX_OTG_CTRL; + break; } diff --git a/drivers/regulator/bd70528-regulator.c b/drivers/regulator/bd70528-regulator.c new file mode 100644 index 000000000000..30e3ed430a8a --- /dev/null +++ b/drivers/regulator/bd70528-regulator.c @@ -0,0 +1,289 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (C) 2018 ROHM Semiconductors +// bd70528-regulator.c ROHM BD70528MWV regulator driver + +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/gpio.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/mfd/rohm-bd70528.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/of_regulator.h> +#include <linux/slab.h> + +#define BUCK_RAMPRATE_250MV 0 +#define BUCK_RAMPRATE_125MV 1 +#define BUCK_RAMP_MAX 250 + +static const struct regulator_linear_range bd70528_buck1_volts[] = { + REGULATOR_LINEAR_RANGE(1200000, 0x00, 0x1, 600000), + REGULATOR_LINEAR_RANGE(2750000, 0x2, 0xf, 50000), +}; +static const struct regulator_linear_range bd70528_buck2_volts[] = { + REGULATOR_LINEAR_RANGE(1200000, 0x00, 0x1, 300000), + REGULATOR_LINEAR_RANGE(1550000, 0x2, 0xd, 50000), + REGULATOR_LINEAR_RANGE(3000000, 0xe, 0xf, 300000), +}; +static const struct regulator_linear_range bd70528_buck3_volts[] = { + REGULATOR_LINEAR_RANGE(800000, 0x00, 0xd, 50000), + REGULATOR_LINEAR_RANGE(1800000, 0xe, 0xf, 0), +}; + +/* All LDOs have same voltage ranges */ +static const struct regulator_linear_range bd70528_ldo_volts[] = { + REGULATOR_LINEAR_RANGE(1650000, 0x0, 0x07, 50000), + REGULATOR_LINEAR_RANGE(2100000, 0x8, 0x0f, 100000), + REGULATOR_LINEAR_RANGE(2850000, 0x10, 0x19, 50000), + REGULATOR_LINEAR_RANGE(3300000, 0x19, 0x1f, 0), +}; + +/* Also both LEDs support same voltages */ +static const unsigned int led_volts[] = { + 20000, 30000 +}; + +static int bd70528_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay) +{ + if (ramp_delay > 0 && ramp_delay <= BUCK_RAMP_MAX) { + unsigned int ramp_value = BUCK_RAMPRATE_250MV; + + if (ramp_delay <= 125) + ramp_value = BUCK_RAMPRATE_125MV; + + return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg, + BD70528_MASK_BUCK_RAMP, + ramp_value << BD70528_SIFT_BUCK_RAMP); + } + dev_err(&rdev->dev, "%s: ramp_delay: %d not supported\n", + rdev->desc->name, ramp_delay); + return -EINVAL; +} + +static int bd70528_led_set_voltage_sel(struct regulator_dev *rdev, + unsigned int sel) +{ + int ret; + + ret = regulator_is_enabled_regmap(rdev); + if (ret < 0) + return ret; + + if (ret == 0) + return regulator_set_voltage_sel_regmap(rdev, sel); + + dev_err(&rdev->dev, + "LED voltage change not allowed when led is enabled\n"); + + return -EBUSY; +} + +static const struct regulator_ops bd70528_buck_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .list_voltage = regulator_list_voltage_linear_range, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_time_sel = regulator_set_voltage_time_sel, + .set_ramp_delay = bd70528_set_ramp_delay, +}; + +static const struct regulator_ops bd70528_ldo_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .list_voltage = regulator_list_voltage_linear_range, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_time_sel = regulator_set_voltage_time_sel, + .set_ramp_delay = bd70528_set_ramp_delay, +}; + +static const struct regulator_ops bd70528_led_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .list_voltage = regulator_list_voltage_table, + .set_voltage_sel = bd70528_led_set_voltage_sel, + .get_voltage_sel = regulator_get_voltage_sel_regmap, +}; + +static const struct regulator_desc bd70528_desc[] = { + { + .name = "buck1", + .of_match = of_match_ptr("BUCK1"), + .regulators_node = of_match_ptr("regulators"), + .id = BD70528_BUCK1, + .ops = &bd70528_buck_ops, + .type = REGULATOR_VOLTAGE, + .linear_ranges = bd70528_buck1_volts, + .n_linear_ranges = ARRAY_SIZE(bd70528_buck1_volts), + .n_voltages = BD70528_BUCK_VOLTS, + .enable_reg = BD70528_REG_BUCK1_EN, + .enable_mask = BD70528_MASK_RUN_EN, + .vsel_reg = BD70528_REG_BUCK1_VOLT, + .vsel_mask = BD70528_MASK_BUCK_VOLT, + .owner = THIS_MODULE, + }, + { + .name = "buck2", + .of_match = of_match_ptr("BUCK2"), + .regulators_node = of_match_ptr("regulators"), + .id = BD70528_BUCK2, + .ops = &bd70528_buck_ops, + .type = REGULATOR_VOLTAGE, + .linear_ranges = bd70528_buck2_volts, + .n_linear_ranges = ARRAY_SIZE(bd70528_buck2_volts), + .n_voltages = BD70528_BUCK_VOLTS, + .enable_reg = BD70528_REG_BUCK2_EN, + .enable_mask = BD70528_MASK_RUN_EN, + .vsel_reg = BD70528_REG_BUCK2_VOLT, + .vsel_mask = BD70528_MASK_BUCK_VOLT, + .owner = THIS_MODULE, + }, + { + .name = "buck3", + .of_match = of_match_ptr("BUCK3"), + .regulators_node = of_match_ptr("regulators"), + .id = BD70528_BUCK3, + .ops = &bd70528_buck_ops, + .type = REGULATOR_VOLTAGE, + .linear_ranges = bd70528_buck3_volts, + .n_linear_ranges = ARRAY_SIZE(bd70528_buck3_volts), + .n_voltages = BD70528_BUCK_VOLTS, + .enable_reg = BD70528_REG_BUCK3_EN, + .enable_mask = BD70528_MASK_RUN_EN, + .vsel_reg = BD70528_REG_BUCK3_VOLT, + .vsel_mask = BD70528_MASK_BUCK_VOLT, + .owner = THIS_MODULE, + }, + { + .name = "ldo1", + .of_match = of_match_ptr("LDO1"), + .regulators_node = of_match_ptr("regulators"), + .id = BD70528_LDO1, + .ops = &bd70528_ldo_ops, + .type = REGULATOR_VOLTAGE, + .linear_ranges = bd70528_ldo_volts, + .n_linear_ranges = ARRAY_SIZE(bd70528_ldo_volts), + .n_voltages = BD70528_LDO_VOLTS, + .enable_reg = BD70528_REG_LDO1_EN, + .enable_mask = BD70528_MASK_RUN_EN, + .vsel_reg = BD70528_REG_LDO1_VOLT, + .vsel_mask = BD70528_MASK_LDO_VOLT, + .owner = THIS_MODULE, + }, + { + .name = "ldo2", + .of_match = of_match_ptr("LDO2"), + .regulators_node = of_match_ptr("regulators"), + .id = BD70528_LDO2, + .ops = &bd70528_ldo_ops, + .type = REGULATOR_VOLTAGE, + .linear_ranges = bd70528_ldo_volts, + .n_linear_ranges = ARRAY_SIZE(bd70528_ldo_volts), + .n_voltages = BD70528_LDO_VOLTS, + .enable_reg = BD70528_REG_LDO2_EN, + .enable_mask = BD70528_MASK_RUN_EN, + .vsel_reg = BD70528_REG_LDO2_VOLT, + .vsel_mask = BD70528_MASK_LDO_VOLT, + .owner = THIS_MODULE, + }, + { + .name = "ldo3", + .of_match = of_match_ptr("LDO3"), + .regulators_node = of_match_ptr("regulators"), + .id = BD70528_LDO3, + .ops = &bd70528_ldo_ops, + .type = REGULATOR_VOLTAGE, + .linear_ranges = bd70528_ldo_volts, + .n_linear_ranges = ARRAY_SIZE(bd70528_ldo_volts), + .n_voltages = BD70528_LDO_VOLTS, + .enable_reg = BD70528_REG_LDO3_EN, + .enable_mask = BD70528_MASK_RUN_EN, + .vsel_reg = BD70528_REG_LDO3_VOLT, + .vsel_mask = BD70528_MASK_LDO_VOLT, + .owner = THIS_MODULE, + }, + { + .name = "ldo_led1", + .of_match = of_match_ptr("LDO_LED1"), + .regulators_node = of_match_ptr("regulators"), + .id = BD70528_LED1, + .ops = &bd70528_led_ops, + .type = REGULATOR_VOLTAGE, + .volt_table = &led_volts[0], + .n_voltages = ARRAY_SIZE(led_volts), + .enable_reg = BD70528_REG_LED_EN, + .enable_mask = BD70528_MASK_LED1_EN, + .vsel_reg = BD70528_REG_LED_VOLT, + .vsel_mask = BD70528_MASK_LED1_VOLT, + .owner = THIS_MODULE, + }, + { + .name = "ldo_led2", + .of_match = of_match_ptr("LDO_LED2"), + .regulators_node = of_match_ptr("regulators"), + .id = BD70528_LED2, + .ops = &bd70528_led_ops, + .type = REGULATOR_VOLTAGE, + .volt_table = &led_volts[0], + .n_voltages = ARRAY_SIZE(led_volts), + .enable_reg = BD70528_REG_LED_EN, + .enable_mask = BD70528_MASK_LED2_EN, + .vsel_reg = BD70528_REG_LED_VOLT, + .vsel_mask = BD70528_MASK_LED2_VOLT, + .owner = THIS_MODULE, + }, + +}; + +static int bd70528_probe(struct platform_device *pdev) +{ + struct rohm_regmap_dev *bd70528; + int i; + struct regulator_config config = { + .dev = pdev->dev.parent, + }; + + bd70528 = dev_get_drvdata(pdev->dev.parent); + if (!bd70528) { + dev_err(&pdev->dev, "No MFD driver data\n"); + return -EINVAL; + } + + config.regmap = bd70528->regmap; + + for (i = 0; i < ARRAY_SIZE(bd70528_desc); i++) { + struct regulator_dev *rdev; + + rdev = devm_regulator_register(&pdev->dev, &bd70528_desc[i], + &config); + if (IS_ERR(rdev)) { + dev_err(&pdev->dev, + "failed to register %s regulator\n", + bd70528_desc[i].name); + return PTR_ERR(rdev); + } + } + return 0; +} + +static struct platform_driver bd70528_regulator = { + .driver = { + .name = "bd70528-pmic" + }, + .probe = bd70528_probe, +}; + +module_platform_driver(bd70528_regulator); + +MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>"); +MODULE_DESCRIPTION("BD70528 voltage regulator driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/regulator/bd718x7-regulator.c b/drivers/regulator/bd718x7-regulator.c index b8dcdc21dc22..b2191be49670 100644 --- a/drivers/regulator/bd718x7-regulator.c +++ b/drivers/regulator/bd718x7-regulator.c @@ -79,7 +79,7 @@ static int bd718xx_set_voltage_sel_pickable_restricted( return regulator_set_voltage_sel_pickable_regmap(rdev, sel); } -static struct regulator_ops bd718xx_pickable_range_ldo_ops = { +static const struct regulator_ops bd718xx_pickable_range_ldo_ops = { .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .is_enabled = regulator_is_enabled_regmap, @@ -88,7 +88,7 @@ static struct regulator_ops bd718xx_pickable_range_ldo_ops = { .get_voltage_sel = regulator_get_voltage_sel_pickable_regmap, }; -static struct regulator_ops bd718xx_pickable_range_buck_ops = { +static const struct regulator_ops bd718xx_pickable_range_buck_ops = { .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .is_enabled = regulator_is_enabled_regmap, @@ -98,7 +98,7 @@ static struct regulator_ops bd718xx_pickable_range_buck_ops = { .set_voltage_time_sel = regulator_set_voltage_time_sel, }; -static struct regulator_ops bd718xx_ldo_regulator_ops = { +static const struct regulator_ops bd718xx_ldo_regulator_ops = { .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .is_enabled = regulator_is_enabled_regmap, @@ -107,7 +107,7 @@ static struct regulator_ops bd718xx_ldo_regulator_ops = { .get_voltage_sel = regulator_get_voltage_sel_regmap, }; -static struct regulator_ops bd718xx_ldo_regulator_nolinear_ops = { +static const struct regulator_ops bd718xx_ldo_regulator_nolinear_ops = { .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .is_enabled = regulator_is_enabled_regmap, @@ -116,7 +116,7 @@ static struct regulator_ops bd718xx_ldo_regulator_nolinear_ops = { .get_voltage_sel = regulator_get_voltage_sel_regmap, }; -static struct regulator_ops bd718xx_buck_regulator_ops = { +static const struct regulator_ops bd718xx_buck_regulator_ops = { .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .is_enabled = regulator_is_enabled_regmap, @@ -126,7 +126,7 @@ static struct regulator_ops bd718xx_buck_regulator_ops = { .set_voltage_time_sel = regulator_set_voltage_time_sel, }; -static struct regulator_ops bd718xx_buck_regulator_nolinear_ops = { +static const struct regulator_ops bd718xx_buck_regulator_nolinear_ops = { .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .is_enabled = regulator_is_enabled_regmap, @@ -137,7 +137,7 @@ static struct regulator_ops bd718xx_buck_regulator_nolinear_ops = { .set_voltage_time_sel = regulator_set_voltage_time_sel, }; -static struct regulator_ops bd718xx_dvs_buck_regulator_ops = { +static const struct regulator_ops bd718xx_dvs_buck_regulator_ops = { .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .is_enabled = regulator_is_enabled_regmap, @@ -350,6 +350,135 @@ static const struct reg_init bd71837_ldo6_inits[] = { }, }; +#define NUM_DVS_BUCKS 4 + +struct of_dvs_setting { + const char *prop; + unsigned int reg; +}; + +static int set_dvs_levels(const struct of_dvs_setting *dvs, + struct device_node *np, + const struct regulator_desc *desc, + struct regmap *regmap) +{ + int ret, i; + unsigned int uv; + + ret = of_property_read_u32(np, dvs->prop, &uv); + if (ret) { + if (ret != -EINVAL) + return ret; + return 0; + } + + for (i = 0; i < desc->n_voltages; i++) { + ret = regulator_desc_list_voltage_linear_range(desc, i); + if (ret < 0) + continue; + if (ret == uv) { + i <<= ffs(desc->vsel_mask) - 1; + ret = regmap_update_bits(regmap, dvs->reg, + DVS_BUCK_RUN_MASK, i); + break; + } + } + return ret; +} + +static int buck4_set_hw_dvs_levels(struct device_node *np, + const struct regulator_desc *desc, + struct regulator_config *cfg) +{ + int ret, i; + const struct of_dvs_setting dvs[] = { + { + .prop = "rohm,dvs-run-voltage", + .reg = BD71837_REG_BUCK4_VOLT_RUN, + }, + }; + + for (i = 0; i < ARRAY_SIZE(dvs); i++) { + ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap); + if (ret) + break; + } + return ret; +} +static int buck3_set_hw_dvs_levels(struct device_node *np, + const struct regulator_desc *desc, + struct regulator_config *cfg) +{ + int ret, i; + const struct of_dvs_setting dvs[] = { + { + .prop = "rohm,dvs-run-voltage", + .reg = BD71837_REG_BUCK3_VOLT_RUN, + }, + }; + + for (i = 0; i < ARRAY_SIZE(dvs); i++) { + ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap); + if (ret) + break; + } + return ret; +} + +static int buck2_set_hw_dvs_levels(struct device_node *np, + const struct regulator_desc *desc, + struct regulator_config *cfg) +{ + int ret, i; + const struct of_dvs_setting dvs[] = { + { + .prop = "rohm,dvs-run-voltage", + .reg = BD718XX_REG_BUCK2_VOLT_RUN, + }, + { + .prop = "rohm,dvs-idle-voltage", + .reg = BD718XX_REG_BUCK2_VOLT_IDLE, + }, + }; + + + + for (i = 0; i < ARRAY_SIZE(dvs); i++) { + ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap); + if (ret) + break; + } + return ret; +} + +static int buck1_set_hw_dvs_levels(struct device_node *np, + const struct regulator_desc *desc, + struct regulator_config *cfg) +{ + int ret, i; + const struct of_dvs_setting dvs[] = { + { + .prop = "rohm,dvs-run-voltage", + .reg = BD718XX_REG_BUCK1_VOLT_RUN, + }, + { + .prop = "rohm,dvs-idle-voltage", + .reg = BD718XX_REG_BUCK1_VOLT_IDLE, + }, + { + .prop = "rohm,dvs-suspend-voltage", + .reg = BD718XX_REG_BUCK1_VOLT_SUSP, + }, + }; + + for (i = 0; i < ARRAY_SIZE(dvs); i++) { + ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap); + if (ret) + break; + } + return ret; +} + static const struct bd718xx_regulator_data bd71847_regulators[] = { { .desc = { @@ -368,6 +497,7 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = { .enable_reg = BD718XX_REG_BUCK1_CTRL, .enable_mask = BD718XX_BUCK_EN, .owner = THIS_MODULE, + .of_parse_cb = buck1_set_hw_dvs_levels, }, .init = { .reg = BD718XX_REG_BUCK1_CTRL, @@ -391,6 +521,7 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = { .enable_reg = BD718XX_REG_BUCK2_CTRL, .enable_mask = BD718XX_BUCK_EN, .owner = THIS_MODULE, + .of_parse_cb = buck2_set_hw_dvs_levels, }, .init = { .reg = BD718XX_REG_BUCK2_CTRL, @@ -662,6 +793,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = { .enable_reg = BD718XX_REG_BUCK1_CTRL, .enable_mask = BD718XX_BUCK_EN, .owner = THIS_MODULE, + .of_parse_cb = buck1_set_hw_dvs_levels, }, .init = { .reg = BD718XX_REG_BUCK1_CTRL, @@ -685,6 +817,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = { .enable_reg = BD718XX_REG_BUCK2_CTRL, .enable_mask = BD718XX_BUCK_EN, .owner = THIS_MODULE, + .of_parse_cb = buck2_set_hw_dvs_levels, }, .init = { .reg = BD718XX_REG_BUCK2_CTRL, @@ -708,6 +841,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = { .enable_reg = BD71837_REG_BUCK3_CTRL, .enable_mask = BD718XX_BUCK_EN, .owner = THIS_MODULE, + .of_parse_cb = buck3_set_hw_dvs_levels, }, .init = { .reg = BD71837_REG_BUCK3_CTRL, @@ -731,6 +865,7 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = { .enable_reg = BD71837_REG_BUCK4_CTRL, .enable_mask = BD718XX_BUCK_EN, .owner = THIS_MODULE, + .of_parse_cb = buck4_set_hw_dvs_levels, }, .init = { .reg = BD71837_REG_BUCK4_CTRL, @@ -1029,6 +1164,7 @@ static int bd718xx_probe(struct platform_device *pdev) }; int i, j, err; + bool use_snvs; mfd = dev_get_drvdata(pdev->dev.parent); if (!mfd) { @@ -1055,27 +1191,28 @@ static int bd718xx_probe(struct platform_device *pdev) BD718XX_REG_REGLOCK); } - /* At poweroff transition PMIC HW disables EN bit for regulators but - * leaves SEL bit untouched. So if state transition from POWEROFF - * is done to SNVS - then all power rails controlled by SW (having - * SEL bit set) stay disabled as EN is cleared. This may result boot - * failure if any crucial systems are powered by these rails. - * + use_snvs = of_property_read_bool(pdev->dev.parent->of_node, + "rohm,reset-snvs-powered"); + + /* * Change the next stage from poweroff to be READY instead of SNVS * for all reset types because OTP loading at READY will clear SEL * bit allowing HW defaults for power rails to be used */ - err = regmap_update_bits(mfd->regmap, BD718XX_REG_TRANS_COND1, - BD718XX_ON_REQ_POWEROFF_MASK | - BD718XX_SWRESET_POWEROFF_MASK | - BD718XX_WDOG_POWEROFF_MASK | - BD718XX_KEY_L_POWEROFF_MASK, - BD718XX_POWOFF_TO_RDY); - if (err) { - dev_err(&pdev->dev, "Failed to change reset target\n"); - goto err; - } else { - dev_dbg(&pdev->dev, "Changed all resets from SVNS to READY\n"); + if (!use_snvs) { + err = regmap_update_bits(mfd->regmap, BD718XX_REG_TRANS_COND1, + BD718XX_ON_REQ_POWEROFF_MASK | + BD718XX_SWRESET_POWEROFF_MASK | + BD718XX_WDOG_POWEROFF_MASK | + BD718XX_KEY_L_POWEROFF_MASK, + BD718XX_POWOFF_TO_RDY); + if (err) { + dev_err(&pdev->dev, "Failed to change reset target\n"); + goto err; + } else { + dev_dbg(&pdev->dev, + "Changed all resets from SVNS to READY\n"); + } } for (i = 0; i < pmic_regulators[mfd->chip_type].r_amount; i++) { @@ -1098,19 +1235,33 @@ static int bd718xx_probe(struct platform_device *pdev) err = PTR_ERR(rdev); goto err; } - /* Regulator register gets the regulator constraints and + + /* + * Regulator register gets the regulator constraints and * applies them (set_machine_constraints). This should have * turned the control register(s) to correct values and we * can now switch the control from PMIC state machine to the * register interface + * + * At poweroff transition PMIC HW disables EN bit for + * regulators but leaves SEL bit untouched. So if state + * transition from POWEROFF is done to SNVS - then all power + * rails controlled by SW (having SEL bit set) stay disabled + * as EN is cleared. This will result boot failure if any + * crucial systems are powered by these rails. We don't + * enable SW control for crucial regulators if snvs state is + * used */ - err = regmap_update_bits(mfd->regmap, r->init.reg, - r->init.mask, r->init.val); - if (err) { - dev_err(&pdev->dev, - "Failed to write BUCK/LDO SEL bit for (%s)\n", - desc->name); - goto err; + if (!use_snvs || !rdev->constraints->always_on || + !rdev->constraints->boot_on) { + err = regmap_update_bits(mfd->regmap, r->init.reg, + r->init.mask, r->init.val); + if (err) { + dev_err(&pdev->dev, + "Failed to take control for (%s)\n", + desc->name); + goto err; + } } for (j = 0; j < r->additional_init_amnt; j++) { err = regmap_update_bits(mfd->regmap, diff --git a/drivers/regulator/bd9571mwv-regulator.c b/drivers/regulator/bd9571mwv-regulator.c index e12dd1f750f3..e690c2ce5b3c 100644 --- a/drivers/regulator/bd9571mwv-regulator.c +++ b/drivers/regulator/bd9571mwv-regulator.c @@ -100,7 +100,7 @@ static int bd9571mwv_reg_set_voltage_sel_regmap(struct regulator_dev *rdev, } /* Operations permitted on AVS voltage regulator */ -static struct regulator_ops avs_ops = { +static const struct regulator_ops avs_ops = { .set_voltage_sel = bd9571mwv_avs_set_voltage_sel_regmap, .map_voltage = regulator_map_voltage_linear, .get_voltage_sel = bd9571mwv_avs_get_voltage_sel_regmap, @@ -108,7 +108,7 @@ static struct regulator_ops avs_ops = { }; /* Operations permitted on voltage regulators */ -static struct regulator_ops reg_ops = { +static const struct regulator_ops reg_ops = { .set_voltage_sel = bd9571mwv_reg_set_voltage_sel_regmap, .map_voltage = regulator_map_voltage_linear, .get_voltage_sel = regulator_get_voltage_sel_regmap, @@ -116,13 +116,13 @@ static struct regulator_ops reg_ops = { }; /* Operations permitted on voltage monitors */ -static struct regulator_ops vid_ops = { +static const struct regulator_ops vid_ops = { .map_voltage = regulator_map_voltage_linear, .get_voltage_sel = regulator_get_voltage_sel_regmap, .list_voltage = regulator_list_voltage_linear, }; -static struct regulator_desc regulators[] = { +static const struct regulator_desc regulators[] = { BD9571MWV_REG("VD09", "vd09", VD09, avs_ops, 0, 0x7f, 0x80, 600000, 10000, 0x3c), BD9571MWV_REG("VD18", "vd18", VD18, vid_ops, BD9571MWV_VD18_VID, 0xf, diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c index b9d7b45c7295..68473d0cc57e 100644 --- a/drivers/regulator/core.c +++ b/drivers/regulator/core.c @@ -23,7 +23,6 @@ #include <linux/mutex.h> #include <linux/suspend.h> #include <linux/delay.h> -#include <linux/gpio.h> #include <linux/gpio/consumer.h> #include <linux/of.h> #include <linux/regmap.h> @@ -82,7 +81,6 @@ struct regulator_enable_gpio { struct gpio_desc *gpiod; u32 enable_count; /* a number of enabled shared GPIO */ u32 request_count; /* a number of requested shared GPIO */ - unsigned int ena_gpio_invert:1; }; /* @@ -145,14 +143,6 @@ static bool regulator_ops_is_valid(struct regulator_dev *rdev, int ops) return false; } -static inline struct regulator_dev *rdev_get_supply(struct regulator_dev *rdev) -{ - if (rdev && rdev->supply) - return rdev->supply->rdev; - - return NULL; -} - /** * regulator_lock_nested - lock a single regulator * @rdev: regulator source @@ -326,7 +316,7 @@ err_unlock: * @rdev: regulator source * @ww_ctx: w/w mutex acquire context * - * Unlock all regulators related with rdev by coupling or suppling. + * Unlock all regulators related with rdev by coupling or supplying. */ static void regulator_unlock_dependent(struct regulator_dev *rdev, struct ww_acquire_ctx *ww_ctx) @@ -341,7 +331,7 @@ static void regulator_unlock_dependent(struct regulator_dev *rdev, * @ww_ctx: w/w mutex acquire context * * This function as a wrapper on regulator_lock_recursive(), which locks - * all regulators related with rdev by coupling or suppling. + * all regulators related with rdev by coupling or supplying. */ static void regulator_lock_dependent(struct regulator_dev *rdev, struct ww_acquire_ctx *ww_ctx) @@ -924,14 +914,14 @@ static int drms_uA_update(struct regulator_dev *rdev) int current_uA = 0, output_uV, input_uV, err; unsigned int mode; - lockdep_assert_held_once(&rdev->mutex.base); - /* * first check to see if we can set modes at all, otherwise just * tell the consumer everything is OK. */ - if (!regulator_ops_is_valid(rdev, REGULATOR_CHANGE_DRMS)) + if (!regulator_ops_is_valid(rdev, REGULATOR_CHANGE_DRMS)) { + rdev_dbg(rdev, "DRMS operation not allowed\n"); return 0; + } if (!rdev->desc->ops->get_optimum_mode && !rdev->desc->ops->set_load) @@ -1003,7 +993,7 @@ static int suspend_set_state(struct regulator_dev *rdev, if (rstate == NULL) return 0; - /* If we have no suspend mode configration don't set anything; + /* If we have no suspend mode configuration don't set anything; * only warn if the driver implements set_suspend_voltage or * set_suspend_mode callback. */ @@ -1131,7 +1121,7 @@ static int machine_constraints_voltage(struct regulator_dev *rdev, int current_uV = _regulator_get_voltage(rdev); if (current_uV == -ENOTRECOVERABLE) { - /* This regulator can't be read and must be initted */ + /* This regulator can't be read and must be initialized */ rdev_info(rdev, "Setting %d-%duV\n", rdev->constraints->min_uV, rdev->constraints->max_uV); @@ -1349,7 +1339,9 @@ static int set_machine_constraints(struct regulator_dev *rdev, * We'll only apply the initial system load if an * initial mode wasn't specified. */ + regulator_lock(rdev); drms_uA_update(rdev); + regulator_unlock(rdev); } if ((rdev->constraints->ramp_delay || rdev->constraints->ramp_disable) @@ -1780,7 +1772,7 @@ static int regulator_resolve_supply(struct regulator_dev *rdev) struct device *dev = rdev->dev.parent; int ret; - /* No supply to resovle? */ + /* No supply to resolve? */ if (!rdev->supply_name) return 0; @@ -2058,15 +2050,7 @@ static void _regulator_put(struct regulator *regulator) debugfs_remove_recursive(regulator->debugfs); if (regulator->dev) { - int count = 0; - struct regulator *r; - - list_for_each_entry(r, &rdev->consumer_list, list) - if (r->dev == regulator->dev) - count++; - - if (count == 1) - device_link_remove(regulator->dev, &rdev->dev); + device_link_remove(regulator->dev, &rdev->dev); /* remove any sysfs entries */ sysfs_remove_link(&rdev->dev.kobj, regulator->supply_name); @@ -2237,38 +2221,21 @@ static int regulator_ena_gpio_request(struct regulator_dev *rdev, { struct regulator_enable_gpio *pin; struct gpio_desc *gpiod; - int ret; - if (config->ena_gpiod) - gpiod = config->ena_gpiod; - else - gpiod = gpio_to_desc(config->ena_gpio); + gpiod = config->ena_gpiod; list_for_each_entry(pin, ®ulator_ena_gpio_list, list) { if (pin->gpiod == gpiod) { - rdev_dbg(rdev, "GPIO %d is already used\n", - config->ena_gpio); + rdev_dbg(rdev, "GPIO is already used\n"); goto update_ena_gpio_to_rdev; } } - if (!config->ena_gpiod) { - ret = gpio_request_one(config->ena_gpio, - GPIOF_DIR_OUT | config->ena_gpio_flags, - rdev_get_name(rdev)); - if (ret) - return ret; - } - pin = kzalloc(sizeof(struct regulator_enable_gpio), GFP_KERNEL); - if (pin == NULL) { - if (!config->ena_gpiod) - gpio_free(config->ena_gpio); + if (pin == NULL) return -ENOMEM; - } pin->gpiod = gpiod; - pin->ena_gpio_invert = config->ena_gpio_invert; list_add(&pin->list, ®ulator_ena_gpio_list); update_ena_gpio_to_rdev: @@ -2289,7 +2256,6 @@ static void regulator_ena_gpio_free(struct regulator_dev *rdev) if (pin->gpiod == rdev->ena_pin->gpiod) { if (pin->request_count <= 1) { pin->request_count = 0; - gpiod_put(pin->gpiod); list_del(&pin->list); kfree(pin); rdev->ena_pin = NULL; @@ -2319,8 +2285,7 @@ static int regulator_ena_gpio_ctrl(struct regulator_dev *rdev, bool enable) if (enable) { /* Enable GPIO at initial use */ if (pin->enable_count == 0) - gpiod_set_value_cansleep(pin->gpiod, - !pin->ena_gpio_invert); + gpiod_set_value_cansleep(pin->gpiod, 1); pin->enable_count++; } else { @@ -2331,8 +2296,7 @@ static int regulator_ena_gpio_ctrl(struct regulator_dev *rdev, bool enable) /* Disable GPIO if not used */ if (pin->enable_count <= 1) { - gpiod_set_value_cansleep(pin->gpiod, - pin->ena_gpio_invert); + gpiod_set_value_cansleep(pin->gpiod, 0); pin->enable_count = 0; } } @@ -2409,7 +2373,7 @@ static int _regulator_do_enable(struct regulator_dev *rdev) * timer wrapping. * in case of multiple timer wrapping, either it can be * detected by out-of-range remaining, or it cannot be - * detected and we gets a panelty of + * detected and we get a penalty of * _regulator_enable_delay(). */ remaining = intended - start_jiffy; @@ -2809,7 +2773,7 @@ static void regulator_disable_work(struct work_struct *work) /** * regulator_disable_deferred - disable regulator output with delay * @regulator: regulator source - * @ms: miliseconds until the regulator is disabled + * @ms: milliseconds until the regulator is disabled * * Execute regulator_disable() on the regulator after a delay. This * is intended for use with devices that require some time to quiesce. @@ -4943,7 +4907,7 @@ regulator_register(const struct regulator_desc *regulator_desc, * device tree until we have handled it over to the core. If the * config that was passed in to this function DOES NOT contain * a descriptor, and the config after this call DOES contain - * a descriptor, we definately got one from parsing the device + * a descriptor, we definitely got one from parsing the device * tree. */ if (!cfg->ena_gpiod && config->ena_gpiod) @@ -4975,15 +4939,13 @@ regulator_register(const struct regulator_desc *regulator_desc, goto clean; } - if (config->ena_gpiod || - ((config->ena_gpio || config->ena_gpio_initialized) && - gpio_is_valid(config->ena_gpio))) { + if (config->ena_gpiod) { mutex_lock(®ulator_list_mutex); ret = regulator_ena_gpio_request(rdev, config); mutex_unlock(®ulator_list_mutex); if (ret != 0) { - rdev_err(rdev, "Failed to request enable GPIO%d: %d\n", - config->ena_gpio, ret); + rdev_err(rdev, "Failed to request enable GPIO: %d\n", + ret); goto clean; } /* The regulator core took over the GPIO descriptor */ @@ -5251,6 +5213,12 @@ struct device *rdev_get_dev(struct regulator_dev *rdev) } EXPORT_SYMBOL_GPL(rdev_get_dev); +struct regmap *rdev_get_regmap(struct regulator_dev *rdev) +{ + return rdev->regmap; +} +EXPORT_SYMBOL_GPL(rdev_get_regmap); + void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data) { return reg_init_data->driver_data; diff --git a/drivers/regulator/cpcap-regulator.c b/drivers/regulator/cpcap-regulator.c index 2131457937b7..e7dab5c4d1d1 100644 --- a/drivers/regulator/cpcap-regulator.c +++ b/drivers/regulator/cpcap-regulator.c @@ -100,12 +100,11 @@ struct cpcap_regulator { struct regulator_desc rdesc; const u16 assign_reg; const u16 assign_mask; - const u16 vsel_shift; }; #define CPCAP_REG(_ID, reg, assignment_reg, assignment_mask, val_tbl, \ - mode_mask, volt_mask, volt_shft, \ - mode_val, off_val, volt_trans_time) { \ + mode_mask, volt_mask, mode_val, off_val, \ + volt_trans_time) { \ .rdesc = { \ .name = #_ID, \ .of_match = of_match_ptr(#_ID), \ @@ -127,7 +126,6 @@ struct cpcap_regulator { }, \ .assign_reg = (assignment_reg), \ .assign_mask = (assignment_mask), \ - .vsel_shift = (volt_shft), \ } struct cpcap_ddata { @@ -336,155 +334,155 @@ static const unsigned int vaudio_val_tbl[] = { 0, 2775000, }; * SW1 to SW4 and SW6 seems to be unused for mapphone. Note that VSIM and * VSIMCARD have a shared resource assignment bit. */ -static struct cpcap_regulator omap4_regulators[] = { +static const struct cpcap_regulator omap4_regulators[] = { CPCAP_REG(SW1, CPCAP_REG_S1C1, CPCAP_REG_ASSIGN2, CPCAP_BIT_SW1_SEL, unknown_val_tbl, - 0, 0, 0, 0, 0, 0), + 0, 0, 0, 0, 0), CPCAP_REG(SW2, CPCAP_REG_S2C1, CPCAP_REG_ASSIGN2, CPCAP_BIT_SW2_SEL, unknown_val_tbl, - 0, 0, 0, 0, 0, 0), + 0, 0, 0, 0, 0), CPCAP_REG(SW3, CPCAP_REG_S3C, CPCAP_REG_ASSIGN2, CPCAP_BIT_SW3_SEL, unknown_val_tbl, - 0, 0, 0, 0, 0, 0), + 0, 0, 0, 0, 0), CPCAP_REG(SW4, CPCAP_REG_S4C1, CPCAP_REG_ASSIGN2, CPCAP_BIT_SW4_SEL, unknown_val_tbl, - 0, 0, 0, 0, 0, 0), + 0, 0, 0, 0, 0), CPCAP_REG(SW5, CPCAP_REG_S5C, CPCAP_REG_ASSIGN2, CPCAP_BIT_SW5_SEL, sw5_val_tbl, - 0x28, 0, 0, 0x20 | CPCAP_REG_OFF_MODE_SEC, 0, 0), + 0x28, 0, 0x20 | CPCAP_REG_OFF_MODE_SEC, 0, 0), CPCAP_REG(SW6, CPCAP_REG_S6C, CPCAP_REG_ASSIGN2, CPCAP_BIT_SW6_SEL, unknown_val_tbl, - 0, 0, 0, 0, 0, 0), + 0, 0, 0, 0, 0), CPCAP_REG(VCAM, CPCAP_REG_VCAMC, CPCAP_REG_ASSIGN2, CPCAP_BIT_VCAM_SEL, vcam_val_tbl, - 0x87, 0x30, 4, 0x3, 0, 420), + 0x87, 0x30, 0x3, 0, 420), CPCAP_REG(VCSI, CPCAP_REG_VCSIC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VCSI_SEL, vcsi_val_tbl, - 0x47, 0x10, 4, 0x43, 0x41, 350), + 0x47, 0x10, 0x43, 0x41, 350), CPCAP_REG(VDAC, CPCAP_REG_VDACC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VDAC_SEL, vdac_val_tbl, - 0x87, 0x30, 4, 0x3, 0, 420), + 0x87, 0x30, 0x3, 0, 420), CPCAP_REG(VDIG, CPCAP_REG_VDIGC, CPCAP_REG_ASSIGN2, CPCAP_BIT_VDIG_SEL, vdig_val_tbl, - 0x87, 0x30, 4, 0x82, 0, 420), + 0x87, 0x30, 0x82, 0, 420), CPCAP_REG(VFUSE, CPCAP_REG_VFUSEC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VFUSE_SEL, vfuse_val_tbl, - 0x80, 0xf, 0, 0x80, 0, 420), + 0x80, 0xf, 0x80, 0, 420), CPCAP_REG(VHVIO, CPCAP_REG_VHVIOC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VHVIO_SEL, vhvio_val_tbl, - 0x17, 0, 0, 0, 0x12, 0), + 0x17, 0, 0, 0x12, 0), CPCAP_REG(VSDIO, CPCAP_REG_VSDIOC, CPCAP_REG_ASSIGN2, CPCAP_BIT_VSDIO_SEL, vsdio_val_tbl, - 0x87, 0x38, 3, 0x82, 0, 420), + 0x87, 0x38, 0x82, 0, 420), CPCAP_REG(VPLL, CPCAP_REG_VPLLC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VPLL_SEL, vpll_val_tbl, - 0x43, 0x18, 3, 0x2, 0, 420), + 0x43, 0x18, 0x2, 0, 420), CPCAP_REG(VRF1, CPCAP_REG_VRF1C, CPCAP_REG_ASSIGN3, CPCAP_BIT_VRF1_SEL, vrf1_val_tbl, - 0xac, 0x2, 1, 0x4, 0, 10), + 0xac, 0x2, 0x4, 0, 10), CPCAP_REG(VRF2, CPCAP_REG_VRF2C, CPCAP_REG_ASSIGN3, CPCAP_BIT_VRF2_SEL, vrf2_val_tbl, - 0x23, 0x8, 3, 0, 0, 10), + 0x23, 0x8, 0, 0, 10), CPCAP_REG(VRFREF, CPCAP_REG_VRFREFC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VRFREF_SEL, vrfref_val_tbl, - 0x23, 0x8, 3, 0, 0, 420), + 0x23, 0x8, 0, 0, 420), CPCAP_REG(VWLAN1, CPCAP_REG_VWLAN1C, CPCAP_REG_ASSIGN3, CPCAP_BIT_VWLAN1_SEL, vwlan1_val_tbl, - 0x47, 0x10, 4, 0, 0, 420), + 0x47, 0x10, 0, 0, 420), CPCAP_REG(VWLAN2, CPCAP_REG_VWLAN2C, CPCAP_REG_ASSIGN3, CPCAP_BIT_VWLAN2_SEL, vwlan2_val_tbl, - 0x20c, 0xc0, 6, 0x20c, 0, 420), + 0x20c, 0xc0, 0x20c, 0, 420), CPCAP_REG(VSIM, CPCAP_REG_VSIMC, CPCAP_REG_ASSIGN3, 0xffff, vsim_val_tbl, - 0x23, 0x8, 3, 0x3, 0, 420), + 0x23, 0x8, 0x3, 0, 420), CPCAP_REG(VSIMCARD, CPCAP_REG_VSIMC, CPCAP_REG_ASSIGN3, 0xffff, vsimcard_val_tbl, - 0x1e80, 0x8, 3, 0x1e00, 0, 420), + 0x1e80, 0x8, 0x1e00, 0, 420), CPCAP_REG(VVIB, CPCAP_REG_VVIBC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VVIB_SEL, vvib_val_tbl, - 0x1, 0xc, 2, 0x1, 0, 500), + 0x1, 0xc, 0x1, 0, 500), CPCAP_REG(VUSB, CPCAP_REG_VUSBC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VUSB_SEL, vusb_val_tbl, - 0x11c, 0x40, 6, 0xc, 0, 0), + 0x11c, 0x40, 0xc, 0, 0), CPCAP_REG(VAUDIO, CPCAP_REG_VAUDIOC, CPCAP_REG_ASSIGN4, CPCAP_BIT_VAUDIO_SEL, vaudio_val_tbl, - 0x16, 0x1, 0, 0x4, 0, 0), + 0x16, 0x1, 0x4, 0, 0), { /* sentinel */ }, }; -static struct cpcap_regulator xoom_regulators[] = { +static const struct cpcap_regulator xoom_regulators[] = { CPCAP_REG(SW1, CPCAP_REG_S1C1, CPCAP_REG_ASSIGN2, CPCAP_BIT_SW1_SEL, unknown_val_tbl, - 0, 0, 0, 0, 0, 0), + 0, 0, 0, 0, 0), CPCAP_REG(SW2, CPCAP_REG_S2C1, CPCAP_REG_ASSIGN2, CPCAP_BIT_SW2_SEL, sw2_sw4_val_tbl, - 0xf00, 0x7f, 0, 0x800, 0, 120), + 0xf00, 0x7f, 0x800, 0, 120), CPCAP_REG(SW3, CPCAP_REG_S3C, CPCAP_REG_ASSIGN2, CPCAP_BIT_SW3_SEL, unknown_val_tbl, - 0, 0, 0, 0, 0, 0), + 0, 0, 0, 0, 0), CPCAP_REG(SW4, CPCAP_REG_S4C1, CPCAP_REG_ASSIGN2, CPCAP_BIT_SW4_SEL, sw2_sw4_val_tbl, - 0xf00, 0x7f, 0, 0x900, 0, 100), + 0xf00, 0x7f, 0x900, 0, 100), CPCAP_REG(SW5, CPCAP_REG_S5C, CPCAP_REG_ASSIGN2, CPCAP_BIT_SW5_SEL, sw5_val_tbl, - 0x2a, 0, 0, 0x22, 0, 0), + 0x2a, 0, 0x22, 0, 0), CPCAP_REG(SW6, CPCAP_REG_S6C, CPCAP_REG_ASSIGN2, CPCAP_BIT_SW6_SEL, unknown_val_tbl, - 0, 0, 0, 0, 0, 0), + 0, 0, 0, 0, 0), CPCAP_REG(VCAM, CPCAP_REG_VCAMC, CPCAP_REG_ASSIGN2, CPCAP_BIT_VCAM_SEL, vcam_val_tbl, - 0x87, 0x30, 4, 0x7, 0, 420), + 0x87, 0x30, 0x7, 0, 420), CPCAP_REG(VCSI, CPCAP_REG_VCSIC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VCSI_SEL, vcsi_val_tbl, - 0x47, 0x10, 4, 0x7, 0, 350), + 0x47, 0x10, 0x7, 0, 350), CPCAP_REG(VDAC, CPCAP_REG_VDACC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VDAC_SEL, vdac_val_tbl, - 0x87, 0x30, 4, 0x3, 0, 420), + 0x87, 0x30, 0x3, 0, 420), CPCAP_REG(VDIG, CPCAP_REG_VDIGC, CPCAP_REG_ASSIGN2, CPCAP_BIT_VDIG_SEL, vdig_val_tbl, - 0x87, 0x30, 4, 0x5, 0, 420), + 0x87, 0x30, 0x5, 0, 420), CPCAP_REG(VFUSE, CPCAP_REG_VFUSEC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VFUSE_SEL, vfuse_val_tbl, - 0x80, 0xf, 0, 0x80, 0, 420), + 0x80, 0xf, 0x80, 0, 420), CPCAP_REG(VHVIO, CPCAP_REG_VHVIOC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VHVIO_SEL, vhvio_val_tbl, - 0x17, 0, 0, 0x2, 0, 0), + 0x17, 0, 0x2, 0, 0), CPCAP_REG(VSDIO, CPCAP_REG_VSDIOC, CPCAP_REG_ASSIGN2, CPCAP_BIT_VSDIO_SEL, vsdio_val_tbl, - 0x87, 0x38, 3, 0x2, 0, 420), + 0x87, 0x38, 0x2, 0, 420), CPCAP_REG(VPLL, CPCAP_REG_VPLLC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VPLL_SEL, vpll_val_tbl, - 0x43, 0x18, 3, 0x1, 0, 420), + 0x43, 0x18, 0x1, 0, 420), CPCAP_REG(VRF1, CPCAP_REG_VRF1C, CPCAP_REG_ASSIGN3, CPCAP_BIT_VRF1_SEL, vrf1_val_tbl, - 0xac, 0x2, 1, 0xc, 0, 10), + 0xac, 0x2, 0xc, 0, 10), CPCAP_REG(VRF2, CPCAP_REG_VRF2C, CPCAP_REG_ASSIGN3, CPCAP_BIT_VRF2_SEL, vrf2_val_tbl, - 0x23, 0x8, 3, 0x3, 0, 10), + 0x23, 0x8, 0x3, 0, 10), CPCAP_REG(VRFREF, CPCAP_REG_VRFREFC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VRFREF_SEL, vrfref_val_tbl, - 0x23, 0x8, 3, 0x3, 0, 420), + 0x23, 0x8, 0x3, 0, 420), CPCAP_REG(VWLAN1, CPCAP_REG_VWLAN1C, CPCAP_REG_ASSIGN3, CPCAP_BIT_VWLAN1_SEL, vwlan1_val_tbl, - 0x47, 0x10, 4, 0x5, 0, 420), + 0x47, 0x10, 0x5, 0, 420), CPCAP_REG(VWLAN2, CPCAP_REG_VWLAN2C, CPCAP_REG_ASSIGN3, CPCAP_BIT_VWLAN2_SEL, vwlan2_val_tbl, - 0x20c, 0xc0, 6, 0x8, 0, 420), + 0x20c, 0xc0, 0x8, 0, 420), CPCAP_REG(VSIM, CPCAP_REG_VSIMC, CPCAP_REG_ASSIGN3, 0xffff, vsim_val_tbl, - 0x23, 0x8, 3, 0x3, 0, 420), + 0x23, 0x8, 0x3, 0, 420), CPCAP_REG(VSIMCARD, CPCAP_REG_VSIMC, CPCAP_REG_ASSIGN3, 0xffff, vsimcard_val_tbl, - 0x1e80, 0x8, 3, 0x1e00, 0, 420), + 0x1e80, 0x8, 0x1e00, 0, 420), CPCAP_REG(VVIB, CPCAP_REG_VVIBC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VVIB_SEL, vvib_val_tbl, - 0x1, 0xc, 2, 0, 0x1, 500), + 0x1, 0xc, 0, 0x1, 500), CPCAP_REG(VUSB, CPCAP_REG_VUSBC, CPCAP_REG_ASSIGN3, CPCAP_BIT_VUSB_SEL, vusb_val_tbl, - 0x11c, 0x40, 6, 0xc, 0, 0), + 0x11c, 0x40, 0xc, 0, 0), CPCAP_REG(VAUDIO, CPCAP_REG_VAUDIOC, CPCAP_REG_ASSIGN4, CPCAP_BIT_VAUDIO_SEL, vaudio_val_tbl, - 0x16, 0x1, 0, 0x4, 0, 0), + 0x16, 0x1, 0x4, 0, 0), { /* sentinel */ }, }; diff --git a/drivers/regulator/da9052-regulator.c b/drivers/regulator/da9052-regulator.c index 207cb3859dcc..cefa3558236d 100644 --- a/drivers/regulator/da9052-regulator.c +++ b/drivers/regulator/da9052-regulator.c @@ -290,10 +290,10 @@ static const struct regulator_ops da9052_ldo_ops = { .disable = regulator_disable_regmap, }; -#define DA9052_LDO(_id, step, min, max, sbits, ebits, abits) \ +#define DA9052_LDO(_id, _name, step, min, max, sbits, ebits, abits) \ {\ .reg_desc = {\ - .name = #_id,\ + .name = #_name,\ .ops = &da9052_ldo_ops,\ .type = REGULATOR_VOLTAGE,\ .id = DA9052_ID_##_id,\ @@ -310,10 +310,10 @@ static const struct regulator_ops da9052_ldo_ops = { .activate_bit = (abits),\ } -#define DA9052_DCDC(_id, step, min, max, sbits, ebits, abits) \ +#define DA9052_DCDC(_id, _name, step, min, max, sbits, ebits, abits) \ {\ .reg_desc = {\ - .name = #_id,\ + .name = #_name,\ .ops = &da9052_dcdc_ops,\ .type = REGULATOR_VOLTAGE,\ .id = DA9052_ID_##_id,\ @@ -331,37 +331,37 @@ static const struct regulator_ops da9052_ldo_ops = { } static struct da9052_regulator_info da9052_regulator_info[] = { - DA9052_DCDC(BUCK1, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBCOREGO), - DA9052_DCDC(BUCK2, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBPROGO), - DA9052_DCDC(BUCK3, 25, 950, 2525, 6, 6, DA9052_SUPPLY_VBMEMGO), - DA9052_DCDC(BUCK4, 50, 1800, 3600, 5, 6, 0), - DA9052_LDO(LDO1, 50, 600, 1800, 5, 6, 0), - DA9052_LDO(LDO2, 25, 600, 1800, 6, 6, DA9052_SUPPLY_VLDO2GO), - DA9052_LDO(LDO3, 25, 1725, 3300, 6, 6, DA9052_SUPPLY_VLDO3GO), - DA9052_LDO(LDO4, 25, 1725, 3300, 6, 6, 0), - DA9052_LDO(LDO5, 50, 1200, 3600, 6, 6, 0), - DA9052_LDO(LDO6, 50, 1200, 3600, 6, 6, 0), - DA9052_LDO(LDO7, 50, 1200, 3600, 6, 6, 0), - DA9052_LDO(LDO8, 50, 1200, 3600, 6, 6, 0), - DA9052_LDO(LDO9, 50, 1250, 3650, 6, 6, 0), - DA9052_LDO(LDO10, 50, 1200, 3600, 6, 6, 0), + DA9052_DCDC(BUCK1, buck1, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBCOREGO), + DA9052_DCDC(BUCK2, buck2, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBPROGO), + DA9052_DCDC(BUCK3, buck3, 25, 950, 2525, 6, 6, DA9052_SUPPLY_VBMEMGO), + DA9052_DCDC(BUCK4, buck4, 50, 1800, 3600, 5, 6, 0), + DA9052_LDO(LDO1, ldo1, 50, 600, 1800, 5, 6, 0), + DA9052_LDO(LDO2, ldo2, 25, 600, 1800, 6, 6, DA9052_SUPPLY_VLDO2GO), + DA9052_LDO(LDO3, ldo3, 25, 1725, 3300, 6, 6, DA9052_SUPPLY_VLDO3GO), + DA9052_LDO(LDO4, ldo4, 25, 1725, 3300, 6, 6, 0), + DA9052_LDO(LDO5, ldo5, 50, 1200, 3600, 6, 6, 0), + DA9052_LDO(LDO6, ldo6, 50, 1200, 3600, 6, 6, 0), + DA9052_LDO(LDO7, ldo7, 50, 1200, 3600, 6, 6, 0), + DA9052_LDO(LDO8, ldo8, 50, 1200, 3600, 6, 6, 0), + DA9052_LDO(LDO9, ldo9, 50, 1250, 3650, 6, 6, 0), + DA9052_LDO(LDO10, ldo10, 50, 1200, 3600, 6, 6, 0), }; static struct da9052_regulator_info da9053_regulator_info[] = { - DA9052_DCDC(BUCK1, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBCOREGO), - DA9052_DCDC(BUCK2, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBPROGO), - DA9052_DCDC(BUCK3, 25, 950, 2525, 6, 6, DA9052_SUPPLY_VBMEMGO), - DA9052_DCDC(BUCK4, 25, 950, 2525, 6, 6, 0), - DA9052_LDO(LDO1, 50, 600, 1800, 5, 6, 0), - DA9052_LDO(LDO2, 25, 600, 1800, 6, 6, DA9052_SUPPLY_VLDO2GO), - DA9052_LDO(LDO3, 25, 1725, 3300, 6, 6, DA9052_SUPPLY_VLDO3GO), - DA9052_LDO(LDO4, 25, 1725, 3300, 6, 6, 0), - DA9052_LDO(LDO5, 50, 1200, 3600, 6, 6, 0), - DA9052_LDO(LDO6, 50, 1200, 3600, 6, 6, 0), - DA9052_LDO(LDO7, 50, 1200, 3600, 6, 6, 0), - DA9052_LDO(LDO8, 50, 1200, 3600, 6, 6, 0), - DA9052_LDO(LDO9, 50, 1250, 3650, 6, 6, 0), - DA9052_LDO(LDO10, 50, 1200, 3600, 6, 6, 0), + DA9052_DCDC(BUCK1, buck1, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBCOREGO), + DA9052_DCDC(BUCK2, buck2, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBPROGO), + DA9052_DCDC(BUCK3, buck3, 25, 950, 2525, 6, 6, DA9052_SUPPLY_VBMEMGO), + DA9052_DCDC(BUCK4, buck4, 25, 950, 2525, 6, 6, 0), + DA9052_LDO(LDO1, ldo1, 50, 600, 1800, 5, 6, 0), + DA9052_LDO(LDO2, ldo2, 25, 600, 1800, 6, 6, DA9052_SUPPLY_VLDO2GO), + DA9052_LDO(LDO3, ldo3, 25, 1725, 3300, 6, 6, DA9052_SUPPLY_VLDO3GO), + DA9052_LDO(LDO4, ldo4, 25, 1725, 3300, 6, 6, 0), + DA9052_LDO(LDO5, ldo5, 50, 1200, 3600, 6, 6, 0), + DA9052_LDO(LDO6, ldo6, 50, 1200, 3600, 6, 6, 0), + DA9052_LDO(LDO7, ldo7, 50, 1200, 3600, 6, 6, 0), + DA9052_LDO(LDO8, ldo8, 50, 1200, 3600, 6, 6, 0), + DA9052_LDO(LDO9, ldo9, 50, 1250, 3650, 6, 6, 0), + DA9052_LDO(LDO10, ldo10, 50, 1200, 3600, 6, 6, 0), }; static inline struct da9052_regulator_info *find_regulator_info(u8 chip_id, diff --git a/drivers/regulator/da9055-regulator.c b/drivers/regulator/da9055-regulator.c index 588c3d2445cf..3c6fac793658 100644 --- a/drivers/regulator/da9055-regulator.c +++ b/drivers/regulator/da9055-regulator.c @@ -48,7 +48,9 @@ #define DA9055_ID_LDO6 7 /* DA9055 BUCK current limit */ -static const int da9055_current_limits[] = { 500000, 600000, 700000, 800000 }; +static const unsigned int da9055_current_limits[] = { + 500000, 600000, 700000, 800000 +}; struct da9055_conf_reg { int reg; @@ -169,39 +171,6 @@ static int da9055_ldo_set_mode(struct regulator_dev *rdev, unsigned int mode) val << volt.sl_shift); } -static int da9055_buck_get_current_limit(struct regulator_dev *rdev) -{ - struct da9055_regulator *regulator = rdev_get_drvdata(rdev); - struct da9055_regulator_info *info = regulator->info; - int ret; - - ret = da9055_reg_read(regulator->da9055, DA9055_REG_BUCK_LIM); - if (ret < 0) - return ret; - - ret &= info->mode.mask; - return da9055_current_limits[ret >> info->mode.shift]; -} - -static int da9055_buck_set_current_limit(struct regulator_dev *rdev, int min_uA, - int max_uA) -{ - struct da9055_regulator *regulator = rdev_get_drvdata(rdev); - struct da9055_regulator_info *info = regulator->info; - int i; - - for (i = ARRAY_SIZE(da9055_current_limits) - 1; i >= 0; i--) { - if ((min_uA <= da9055_current_limits[i]) && - (da9055_current_limits[i] <= max_uA)) - return da9055_reg_update(regulator->da9055, - DA9055_REG_BUCK_LIM, - info->mode.mask, - i << info->mode.shift); - } - - return -EINVAL; -} - static int da9055_regulator_get_voltage_sel(struct regulator_dev *rdev) { struct da9055_regulator *regulator = rdev_get_drvdata(rdev); @@ -329,8 +298,8 @@ static const struct regulator_ops da9055_buck_ops = { .get_mode = da9055_buck_get_mode, .set_mode = da9055_buck_set_mode, - .get_current_limit = da9055_buck_get_current_limit, - .set_current_limit = da9055_buck_set_current_limit, + .get_current_limit = regulator_get_current_limit_regmap, + .set_current_limit = regulator_set_current_limit_regmap, .get_voltage_sel = da9055_regulator_get_voltage_sel, .set_voltage_sel = da9055_regulator_set_voltage_sel, @@ -407,6 +376,10 @@ static const struct regulator_ops da9055_ldo_ops = { .uV_step = (step) * 1000,\ .linear_min_sel = (voffset),\ .owner = THIS_MODULE,\ + .curr_table = da9055_current_limits,\ + .n_current_limits = ARRAY_SIZE(da9055_current_limits),\ + .csel_reg = DA9055_REG_BUCK_LIM,\ + .csel_mask = (mbits),\ },\ .conf = {\ .reg = DA9055_REG_BCORE_CONT + DA9055_ID_##_id, \ @@ -457,7 +430,6 @@ static int da9055_gpio_init(struct da9055_regulator *regulator, int gpio_mux = pdata->gpio_ren[id]; config->ena_gpiod = pdata->ena_gpiods[id]; - config->ena_gpio_invert = 1; /* * GPI pin is muxed with regulator to control the diff --git a/drivers/regulator/da9062-regulator.c b/drivers/regulator/da9062-regulator.c index 34a70d9dc450..b064d8a19d4c 100644 --- a/drivers/regulator/da9062-regulator.c +++ b/drivers/regulator/da9062-regulator.c @@ -126,7 +126,7 @@ static int da9062_set_current_limit(struct regulator_dev *rdev, const struct da9062_regulator_info *rinfo = regl->info; int n, tval; - for (n = 0; n < rinfo->n_current_limits; n++) { + for (n = rinfo->n_current_limits - 1; n >= 0; n--) { tval = rinfo->current_limits[n]; if (tval >= min_ua && tval <= max_ua) return regmap_field_write(regl->ilimit, n); @@ -992,7 +992,6 @@ static int da9062_regulator_probe(struct platform_device *pdev) struct regulator_config config = { }; const struct da9062_regulator_info *rinfo; int irq, n, ret; - size_t size; int max_regulators; switch (chip->chip_type) { @@ -1010,9 +1009,8 @@ static int da9062_regulator_probe(struct platform_device *pdev) } /* Allocate memory required by usable regulators */ - size = sizeof(struct da9062_regulators) + - max_regulators * sizeof(struct da9062_regulator); - regulators = devm_kzalloc(&pdev->dev, size, GFP_KERNEL); + regulators = devm_kzalloc(&pdev->dev, struct_size(regulators, regulator, + max_regulators), GFP_KERNEL); if (!regulators) return -ENOMEM; @@ -1029,31 +1027,50 @@ static int da9062_regulator_probe(struct platform_device *pdev) regl->desc.type = REGULATOR_VOLTAGE; regl->desc.owner = THIS_MODULE; - if (regl->info->mode.reg) + if (regl->info->mode.reg) { regl->mode = devm_regmap_field_alloc( &pdev->dev, chip->regmap, regl->info->mode); - if (regl->info->suspend.reg) + if (IS_ERR(regl->mode)) + return PTR_ERR(regl->mode); + } + + if (regl->info->suspend.reg) { regl->suspend = devm_regmap_field_alloc( &pdev->dev, chip->regmap, regl->info->suspend); - if (regl->info->sleep.reg) + if (IS_ERR(regl->suspend)) + return PTR_ERR(regl->suspend); + } + + if (regl->info->sleep.reg) { regl->sleep = devm_regmap_field_alloc( &pdev->dev, chip->regmap, regl->info->sleep); - if (regl->info->suspend_sleep.reg) + if (IS_ERR(regl->sleep)) + return PTR_ERR(regl->sleep); + } + + if (regl->info->suspend_sleep.reg) { regl->suspend_sleep = devm_regmap_field_alloc( &pdev->dev, chip->regmap, regl->info->suspend_sleep); - if (regl->info->ilimit.reg) + if (IS_ERR(regl->suspend_sleep)) + return PTR_ERR(regl->suspend_sleep); + } + + if (regl->info->ilimit.reg) { regl->ilimit = devm_regmap_field_alloc( &pdev->dev, chip->regmap, regl->info->ilimit); + if (IS_ERR(regl->ilimit)) + return PTR_ERR(regl->ilimit); + } /* Register regulator */ memset(&config, 0, sizeof(config)); diff --git a/drivers/regulator/da9063-regulator.c b/drivers/regulator/da9063-regulator.c index 8cbcd2a3eb20..2b0c7a85306a 100644 --- a/drivers/regulator/da9063-regulator.c +++ b/drivers/regulator/da9063-regulator.c @@ -167,7 +167,7 @@ static int da9063_set_current_limit(struct regulator_dev *rdev, const struct da9063_regulator_info *rinfo = regl->info; int n, tval; - for (n = 0; n < rinfo->n_current_limits; n++) { + for (n = rinfo->n_current_limits - 1; n >= 0; n--) { tval = rinfo->current_limits[n]; if (tval >= min_uA && tval <= max_uA) return regmap_field_write(regl->ilimit, n); @@ -739,7 +739,6 @@ static int da9063_regulator_probe(struct platform_device *pdev) struct regulator_config config; bool bcores_merged, bmem_bio_merged; int id, irq, n, n_regulators, ret, val; - size_t size; regl_pdata = da9063_pdata ? da9063_pdata->regulators_pdata : NULL; @@ -784,9 +783,8 @@ static int da9063_regulator_probe(struct platform_device *pdev) n_regulators--; /* remove BMEM_BIO_MERGED */ /* Allocate memory required by usable regulators */ - size = sizeof(struct da9063_regulators) + - n_regulators * sizeof(struct da9063_regulator); - regulators = devm_kzalloc(&pdev->dev, size, GFP_KERNEL); + regulators = devm_kzalloc(&pdev->dev, struct_size(regulators, + regulator, n_regulators), GFP_KERNEL); if (!regulators) return -ENOMEM; @@ -835,21 +833,40 @@ static int da9063_regulator_probe(struct platform_device *pdev) regl->desc.type = REGULATOR_VOLTAGE; regl->desc.owner = THIS_MODULE; - if (regl->info->mode.reg) + if (regl->info->mode.reg) { regl->mode = devm_regmap_field_alloc(&pdev->dev, da9063->regmap, regl->info->mode); - if (regl->info->suspend.reg) + if (IS_ERR(regl->mode)) + return PTR_ERR(regl->mode); + } + + if (regl->info->suspend.reg) { regl->suspend = devm_regmap_field_alloc(&pdev->dev, da9063->regmap, regl->info->suspend); - if (regl->info->sleep.reg) + if (IS_ERR(regl->suspend)) + return PTR_ERR(regl->suspend); + } + + if (regl->info->sleep.reg) { regl->sleep = devm_regmap_field_alloc(&pdev->dev, da9063->regmap, regl->info->sleep); - if (regl->info->suspend_sleep.reg) + if (IS_ERR(regl->sleep)) + return PTR_ERR(regl->sleep); + } + + if (regl->info->suspend_sleep.reg) { regl->suspend_sleep = devm_regmap_field_alloc(&pdev->dev, da9063->regmap, regl->info->suspend_sleep); - if (regl->info->ilimit.reg) + if (IS_ERR(regl->suspend_sleep)) + return PTR_ERR(regl->suspend_sleep); + } + + if (regl->info->ilimit.reg) { regl->ilimit = devm_regmap_field_alloc(&pdev->dev, da9063->regmap, regl->info->ilimit); + if (IS_ERR(regl->ilimit)) + return PTR_ERR(regl->ilimit); + } /* Register regulator */ memset(&config, 0, sizeof(config)); diff --git a/drivers/regulator/da9210-regulator.c b/drivers/regulator/da9210-regulator.c index 84dba64ed11e..528303771723 100644 --- a/drivers/regulator/da9210-regulator.c +++ b/drivers/regulator/da9210-regulator.c @@ -41,10 +41,6 @@ static const struct regmap_config da9210_regmap_config = { .val_bits = 8, }; -static int da9210_set_current_limit(struct regulator_dev *rdev, int min_uA, - int max_uA); -static int da9210_get_current_limit(struct regulator_dev *rdev); - static const struct regulator_ops da9210_buck_ops = { .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, @@ -52,8 +48,8 @@ static const struct regulator_ops da9210_buck_ops = { .set_voltage_sel = regulator_set_voltage_sel_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, .list_voltage = regulator_list_voltage_linear, - .set_current_limit = da9210_set_current_limit, - .get_current_limit = da9210_get_current_limit, + .set_current_limit = regulator_set_current_limit_regmap, + .get_current_limit = regulator_get_current_limit_regmap, }; /* Default limits measured in millivolts and milliamps */ @@ -62,7 +58,7 @@ static const struct regulator_ops da9210_buck_ops = { #define DA9210_STEP_MV 10 /* Current limits for buck (uA) indices corresponds with register values */ -static const int da9210_buck_limits[] = { +static const unsigned int da9210_buck_limits[] = { 1600000, 1800000, 2000000, 2200000, 2400000, 2600000, 2800000, 3000000, 3200000, 3400000, 3600000, 3800000, 4000000, 4200000, 4400000, 4600000 }; @@ -80,47 +76,12 @@ static const struct regulator_desc da9210_reg = { .enable_reg = DA9210_REG_BUCK_CONT, .enable_mask = DA9210_BUCK_EN, .owner = THIS_MODULE, + .curr_table = da9210_buck_limits, + .n_current_limits = ARRAY_SIZE(da9210_buck_limits), + .csel_reg = DA9210_REG_BUCK_ILIM, + .csel_mask = DA9210_BUCK_ILIM_MASK, }; -static int da9210_set_current_limit(struct regulator_dev *rdev, int min_uA, - int max_uA) -{ - struct da9210 *chip = rdev_get_drvdata(rdev); - unsigned int sel; - int i; - - /* search for closest to maximum */ - for (i = ARRAY_SIZE(da9210_buck_limits)-1; i >= 0; i--) { - if (min_uA <= da9210_buck_limits[i] && - max_uA >= da9210_buck_limits[i]) { - sel = i; - sel = sel << DA9210_BUCK_ILIM_SHIFT; - return regmap_update_bits(chip->regmap, - DA9210_REG_BUCK_ILIM, - DA9210_BUCK_ILIM_MASK, sel); - } - } - - return -EINVAL; -} - -static int da9210_get_current_limit(struct regulator_dev *rdev) -{ - struct da9210 *chip = rdev_get_drvdata(rdev); - unsigned int data; - unsigned int sel; - int ret; - - ret = regmap_read(chip->regmap, DA9210_REG_BUCK_ILIM, &data); - if (ret < 0) - return ret; - - /* select one of 16 values: 0000 (1600mA) to 1111 (4600mA) */ - sel = (data & DA9210_BUCK_ILIM_MASK) >> DA9210_BUCK_ILIM_SHIFT; - - return da9210_buck_limits[sel]; -} - static irqreturn_t da9210_irq_handler(int irq, void *data) { struct da9210 *chip = data; diff --git a/drivers/regulator/fan53555.c b/drivers/regulator/fan53555.c index a3bc8037153e..771a06d1900d 100644 --- a/drivers/regulator/fan53555.c +++ b/drivers/regulator/fan53555.c @@ -40,7 +40,6 @@ /* VSEL bit definitions */ #define VSEL_BUCK_EN (1 << 7) #define VSEL_MODE (1 << 6) -#define VSEL_NSEL_MASK 0x3F /* Chip ID and Verison */ #define DIE_ID 0x0F /* ID1 */ #define DIE_REV 0x0F /* ID2 */ @@ -49,14 +48,26 @@ #define CTL_SLEW_MASK (0x7 << 4) #define CTL_SLEW_SHIFT 4 #define CTL_RESET (1 << 2) +#define CTL_MODE_VSEL0_MODE BIT(0) +#define CTL_MODE_VSEL1_MODE BIT(1) #define FAN53555_NVOLTAGES 64 /* Numbers of voltages */ +#define FAN53526_NVOLTAGES 128 enum fan53555_vendor { - FAN53555_VENDOR_FAIRCHILD = 0, + FAN53526_VENDOR_FAIRCHILD = 0, + FAN53555_VENDOR_FAIRCHILD, FAN53555_VENDOR_SILERGY, }; +enum { + FAN53526_CHIP_ID_01 = 1, +}; + +enum { + FAN53526_CHIP_REV_08 = 8, +}; + /* IC Type */ enum { FAN53555_CHIP_ID_00 = 0, @@ -94,8 +105,12 @@ struct fan53555_device_info { /* Voltage range and step(linear) */ unsigned int vsel_min; unsigned int vsel_step; + unsigned int vsel_count; /* Voltage slew rate limiting */ unsigned int slew_rate; + /* Mode */ + unsigned int mode_reg; + unsigned int mode_mask; /* Sleep voltage cache */ unsigned int sleep_vol_cache; }; @@ -111,7 +126,7 @@ static int fan53555_set_suspend_voltage(struct regulator_dev *rdev, int uV) if (ret < 0) return ret; ret = regmap_update_bits(di->regmap, di->sleep_reg, - VSEL_NSEL_MASK, ret); + di->desc.vsel_mask, ret); if (ret < 0) return ret; /* Cache the sleep voltage setting. @@ -143,11 +158,11 @@ static int fan53555_set_mode(struct regulator_dev *rdev, unsigned int mode) switch (mode) { case REGULATOR_MODE_FAST: - regmap_update_bits(di->regmap, di->vol_reg, - VSEL_MODE, VSEL_MODE); + regmap_update_bits(di->regmap, di->mode_reg, + di->mode_mask, di->mode_mask); break; case REGULATOR_MODE_NORMAL: - regmap_update_bits(di->regmap, di->vol_reg, VSEL_MODE, 0); + regmap_update_bits(di->regmap, di->vol_reg, di->mode_mask, 0); break; default: return -EINVAL; @@ -161,10 +176,10 @@ static unsigned int fan53555_get_mode(struct regulator_dev *rdev) unsigned int val; int ret = 0; - ret = regmap_read(di->regmap, di->vol_reg, &val); + ret = regmap_read(di->regmap, di->mode_reg, &val); if (ret < 0) return ret; - if (val & VSEL_MODE) + if (val & di->mode_mask) return REGULATOR_MODE_FAST; else return REGULATOR_MODE_NORMAL; @@ -219,6 +234,34 @@ static const struct regulator_ops fan53555_regulator_ops = { .set_suspend_disable = fan53555_set_suspend_disable, }; +static int fan53526_voltages_setup_fairchild(struct fan53555_device_info *di) +{ + /* Init voltage range and step */ + switch (di->chip_id) { + case FAN53526_CHIP_ID_01: + switch (di->chip_rev) { + case FAN53526_CHIP_REV_08: + di->vsel_min = 600000; + di->vsel_step = 6250; + break; + default: + dev_err(di->dev, + "Chip ID %d with rev %d not supported!\n", + di->chip_id, di->chip_rev); + return -EINVAL; + } + break; + default: + dev_err(di->dev, + "Chip ID %d not supported!\n", di->chip_id); + return -EINVAL; + } + + di->vsel_count = FAN53526_NVOLTAGES; + + return 0; +} + static int fan53555_voltages_setup_fairchild(struct fan53555_device_info *di) { /* Init voltage range and step */ @@ -257,6 +300,8 @@ static int fan53555_voltages_setup_fairchild(struct fan53555_device_info *di) return -EINVAL; } + di->vsel_count = FAN53555_NVOLTAGES; + return 0; } @@ -274,6 +319,8 @@ static int fan53555_voltages_setup_silergy(struct fan53555_device_info *di) return -EINVAL; } + di->vsel_count = FAN53555_NVOLTAGES; + return 0; } @@ -302,7 +349,35 @@ static int fan53555_device_setup(struct fan53555_device_info *di, return -EINVAL; } + /* Setup mode control register */ + switch (di->vendor) { + case FAN53526_VENDOR_FAIRCHILD: + di->mode_reg = FAN53555_CONTROL; + + switch (pdata->sleep_vsel_id) { + case FAN53555_VSEL_ID_0: + di->mode_mask = CTL_MODE_VSEL1_MODE; + break; + case FAN53555_VSEL_ID_1: + di->mode_mask = CTL_MODE_VSEL0_MODE; + break; + } + break; + case FAN53555_VENDOR_FAIRCHILD: + case FAN53555_VENDOR_SILERGY: + di->mode_reg = di->vol_reg; + di->mode_mask = VSEL_MODE; + break; + default: + dev_err(di->dev, "vendor %d not supported!\n", di->vendor); + return -EINVAL; + } + + /* Setup voltage range */ switch (di->vendor) { + case FAN53526_VENDOR_FAIRCHILD: + ret = fan53526_voltages_setup_fairchild(di); + break; case FAN53555_VENDOR_FAIRCHILD: ret = fan53555_voltages_setup_fairchild(di); break; @@ -326,13 +401,13 @@ static int fan53555_regulator_register(struct fan53555_device_info *di, rdesc->supply_name = "vin"; rdesc->ops = &fan53555_regulator_ops; rdesc->type = REGULATOR_VOLTAGE; - rdesc->n_voltages = FAN53555_NVOLTAGES; + rdesc->n_voltages = di->vsel_count; rdesc->enable_reg = di->vol_reg; rdesc->enable_mask = VSEL_BUCK_EN; rdesc->min_uV = di->vsel_min; rdesc->uV_step = di->vsel_step; rdesc->vsel_reg = di->vol_reg; - rdesc->vsel_mask = VSEL_NSEL_MASK; + rdesc->vsel_mask = di->vsel_count - 1; rdesc->owner = THIS_MODULE; di->rdev = devm_regulator_register(di->dev, &di->desc, config); @@ -368,6 +443,9 @@ static struct fan53555_platform_data *fan53555_parse_dt(struct device *dev, static const struct of_device_id fan53555_dt_ids[] = { { + .compatible = "fcs,fan53526", + .data = (void *)FAN53526_VENDOR_FAIRCHILD, + }, { .compatible = "fcs,fan53555", .data = (void *)FAN53555_VENDOR_FAIRCHILD }, { @@ -412,11 +490,13 @@ static int fan53555_regulator_probe(struct i2c_client *client, } else { /* if no ramp constraint set, get the pdata ramp_delay */ if (!di->regulator->constraints.ramp_delay) { - int slew_idx = (pdata->slew_rate & 0x7) - ? pdata->slew_rate : 0; + if (pdata->slew_rate >= ARRAY_SIZE(slew_rates)) { + dev_err(&client->dev, "Invalid slew_rate\n"); + return -EINVAL; + } di->regulator->constraints.ramp_delay - = slew_rates[slew_idx]; + = slew_rates[pdata->slew_rate]; } di->vendor = id->driver_data; @@ -467,6 +547,9 @@ static int fan53555_regulator_probe(struct i2c_client *client, static const struct i2c_device_id fan53555_id[] = { { + .name = "fan53526", + .driver_data = FAN53526_VENDOR_FAIRCHILD + }, { .name = "fan53555", .driver_data = FAN53555_VENDOR_FAIRCHILD }, { diff --git a/drivers/regulator/fixed.c b/drivers/regulator/fixed.c index 9abdb9130766..b5afc9db2c61 100644 --- a/drivers/regulator/fixed.c +++ b/drivers/regulator/fixed.c @@ -79,15 +79,6 @@ of_get_fixed_voltage_config(struct device *dev, of_property_read_u32(np, "startup-delay-us", &config->startup_delay); - /* - * FIXME: we pulled active low/high and open drain handling into - * gpiolib so it will be handled there. Delete this in the second - * step when we also remove the custom inversion handling for all - * legacy boardfiles. - */ - config->enable_high = 1; - config->gpio_is_open_drain = 0; - if (of_find_property(np, "vin-supply", NULL)) config->input_supply = "vin"; @@ -151,24 +142,14 @@ static int reg_fixed_voltage_probe(struct platform_device *pdev) drvdata->desc.fixed_uV = config->microvolts; - cfg.ena_gpio_invert = !config->enable_high; - if (config->enabled_at_boot) { - if (config->enable_high) - gflags = GPIOD_OUT_HIGH; - else - gflags = GPIOD_OUT_LOW; - } else { - if (config->enable_high) - gflags = GPIOD_OUT_LOW; - else - gflags = GPIOD_OUT_HIGH; - } - if (config->gpio_is_open_drain) { - if (gflags == GPIOD_OUT_HIGH) - gflags = GPIOD_OUT_HIGH_OPEN_DRAIN; - else - gflags = GPIOD_OUT_LOW_OPEN_DRAIN; - } + /* + * The signal will be inverted by the GPIO core if flagged so in the + * decriptor. + */ + if (config->enabled_at_boot) + gflags = GPIOD_OUT_HIGH; + else + gflags = GPIOD_OUT_LOW; /* * Some fixed regulators share the enable line between two diff --git a/drivers/regulator/gpio-regulator.c b/drivers/regulator/gpio-regulator.c index b2f5ec4f658a..6157001df0a4 100644 --- a/drivers/regulator/gpio-regulator.c +++ b/drivers/regulator/gpio-regulator.c @@ -30,16 +30,15 @@ #include <linux/regulator/machine.h> #include <linux/regulator/of_regulator.h> #include <linux/regulator/gpio-regulator.h> -#include <linux/gpio.h> +#include <linux/gpio/consumer.h> #include <linux/slab.h> #include <linux/of.h> -#include <linux/of_gpio.h> struct gpio_regulator_data { struct regulator_desc desc; struct regulator_dev *dev; - struct gpio *gpios; + struct gpio_desc **gpiods; int nr_gpios; struct gpio_regulator_state *states; @@ -82,7 +81,7 @@ static int gpio_regulator_set_voltage(struct regulator_dev *dev, for (ptr = 0; ptr < data->nr_gpios; ptr++) { state = (target & (1 << ptr)) >> ptr; - gpio_set_value_cansleep(data->gpios[ptr].gpio, state); + gpiod_set_value_cansleep(data->gpiods[ptr], state); } data->state = target; @@ -119,7 +118,7 @@ static int gpio_regulator_set_current_limit(struct regulator_dev *dev, for (ptr = 0; ptr < data->nr_gpios; ptr++) { state = (target & (1 << ptr)) >> ptr; - gpio_set_value_cansleep(data->gpios[ptr].gpio, state); + gpiod_set_value_cansleep(data->gpiods[ptr], state); } data->state = target; @@ -138,7 +137,8 @@ of_get_gpio_regulator_config(struct device *dev, struct device_node *np, { struct gpio_regulator_config *config; const char *regtype; - int proplen, gpio, i; + int proplen, i; + int ngpios; int ret; config = devm_kzalloc(dev, @@ -153,59 +153,36 @@ of_get_gpio_regulator_config(struct device *dev, struct device_node *np, config->supply_name = config->init_data->constraints.name; - if (of_property_read_bool(np, "enable-active-high")) - config->enable_high = true; - if (of_property_read_bool(np, "enable-at-boot")) config->enabled_at_boot = true; of_property_read_u32(np, "startup-delay-us", &config->startup_delay); - config->enable_gpio = of_get_named_gpio(np, "enable-gpio", 0); - if (config->enable_gpio < 0 && config->enable_gpio != -ENOENT) - return ERR_PTR(config->enable_gpio); - - /* Fetch GPIOs. - optional property*/ - ret = of_gpio_count(np); - if ((ret < 0) && (ret != -ENOENT)) - return ERR_PTR(ret); - - if (ret > 0) { - config->nr_gpios = ret; - config->gpios = devm_kcalloc(dev, - config->nr_gpios, sizeof(struct gpio), - GFP_KERNEL); - if (!config->gpios) + /* Fetch GPIO init levels */ + ngpios = gpiod_count(dev, NULL); + if (ngpios > 0) { + config->gflags = devm_kzalloc(dev, + sizeof(enum gpiod_flags) + * ngpios, + GFP_KERNEL); + if (!config->gflags) return ERR_PTR(-ENOMEM); - proplen = of_property_count_u32_elems(np, "gpios-states"); - /* optional property */ - if (proplen < 0) - proplen = 0; + for (i = 0; i < ngpios; i++) { + u32 val; - if (proplen > 0 && proplen != config->nr_gpios) { - dev_warn(dev, "gpios <-> gpios-states mismatch\n"); - proplen = 0; - } + ret = of_property_read_u32_index(np, "gpios-states", i, + &val); - for (i = 0; i < config->nr_gpios; i++) { - gpio = of_get_named_gpio(np, "gpios", i); - if (gpio < 0) { - if (gpio != -ENOENT) - return ERR_PTR(gpio); - break; - } - config->gpios[i].gpio = gpio; - config->gpios[i].label = config->supply_name; - if (proplen > 0) { - of_property_read_u32_index(np, "gpios-states", - i, &ret); - if (ret) - config->gpios[i].flags = - GPIOF_OUT_INIT_HIGH; - } + /* Default to high per specification */ + if (ret) + config->gflags[i] = GPIOD_OUT_HIGH; + else + config->gflags[i] = + val ? GPIOD_OUT_HIGH : GPIOD_OUT_LOW; } } + config->ngpios = ngpios; /* Fetch states. */ proplen = of_property_count_u32_elems(np, "states"); @@ -251,59 +228,56 @@ static struct regulator_ops gpio_regulator_current_ops = { static int gpio_regulator_probe(struct platform_device *pdev) { - struct gpio_regulator_config *config = dev_get_platdata(&pdev->dev); - struct device_node *np = pdev->dev.of_node; + struct device *dev = &pdev->dev; + struct gpio_regulator_config *config = dev_get_platdata(dev); + struct device_node *np = dev->of_node; struct gpio_regulator_data *drvdata; struct regulator_config cfg = { }; - int ptr, ret, state; + enum gpiod_flags gflags; + int ptr, ret, state, i; - drvdata = devm_kzalloc(&pdev->dev, sizeof(struct gpio_regulator_data), + drvdata = devm_kzalloc(dev, sizeof(struct gpio_regulator_data), GFP_KERNEL); if (drvdata == NULL) return -ENOMEM; if (np) { - config = of_get_gpio_regulator_config(&pdev->dev, np, + config = of_get_gpio_regulator_config(dev, np, &drvdata->desc); if (IS_ERR(config)) return PTR_ERR(config); } - drvdata->desc.name = kstrdup(config->supply_name, GFP_KERNEL); + drvdata->desc.name = devm_kstrdup(dev, config->supply_name, GFP_KERNEL); if (drvdata->desc.name == NULL) { - dev_err(&pdev->dev, "Failed to allocate supply name\n"); + dev_err(dev, "Failed to allocate supply name\n"); return -ENOMEM; } - if (config->nr_gpios != 0) { - drvdata->gpios = kmemdup(config->gpios, - config->nr_gpios * sizeof(struct gpio), - GFP_KERNEL); - if (drvdata->gpios == NULL) { - dev_err(&pdev->dev, "Failed to allocate gpio data\n"); - ret = -ENOMEM; - goto err_name; - } - - drvdata->nr_gpios = config->nr_gpios; - ret = gpio_request_array(drvdata->gpios, drvdata->nr_gpios); - if (ret) { - if (ret != -EPROBE_DEFER) - dev_err(&pdev->dev, - "Could not obtain regulator setting GPIOs: %d\n", - ret); - goto err_memgpio; - } + drvdata->gpiods = devm_kzalloc(dev, sizeof(struct gpio_desc *), + GFP_KERNEL); + if (!drvdata->gpiods) + return -ENOMEM; + for (i = 0; i < config->ngpios; i++) { + drvdata->gpiods[i] = devm_gpiod_get_index(dev, + NULL, + i, + config->gflags[i]); + if (IS_ERR(drvdata->gpiods[i])) + return PTR_ERR(drvdata->gpiods[i]); + /* This is good to know */ + gpiod_set_consumer_name(drvdata->gpiods[i], drvdata->desc.name); } + drvdata->nr_gpios = config->ngpios; - drvdata->states = kmemdup(config->states, - config->nr_states * - sizeof(struct gpio_regulator_state), - GFP_KERNEL); + drvdata->states = devm_kmemdup(dev, + config->states, + config->nr_states * + sizeof(struct gpio_regulator_state), + GFP_KERNEL); if (drvdata->states == NULL) { - dev_err(&pdev->dev, "Failed to allocate state data\n"); - ret = -ENOMEM; - goto err_stategpio; + dev_err(dev, "Failed to allocate state data\n"); + return -ENOMEM; } drvdata->nr_states = config->nr_states; @@ -322,61 +296,46 @@ static int gpio_regulator_probe(struct platform_device *pdev) drvdata->desc.ops = &gpio_regulator_current_ops; break; default: - dev_err(&pdev->dev, "No regulator type set\n"); - ret = -EINVAL; - goto err_memstate; + dev_err(dev, "No regulator type set\n"); + return -EINVAL; } /* build initial state from gpio init data. */ state = 0; for (ptr = 0; ptr < drvdata->nr_gpios; ptr++) { - if (config->gpios[ptr].flags & GPIOF_OUT_INIT_HIGH) + if (config->gflags[ptr] == GPIOD_OUT_HIGH) state |= (1 << ptr); } drvdata->state = state; - cfg.dev = &pdev->dev; + cfg.dev = dev; cfg.init_data = config->init_data; cfg.driver_data = drvdata; cfg.of_node = np; - if (gpio_is_valid(config->enable_gpio)) { - cfg.ena_gpio = config->enable_gpio; - cfg.ena_gpio_initialized = true; - } - cfg.ena_gpio_invert = !config->enable_high; - if (config->enabled_at_boot) { - if (config->enable_high) - cfg.ena_gpio_flags |= GPIOF_OUT_INIT_HIGH; - else - cfg.ena_gpio_flags |= GPIOF_OUT_INIT_LOW; - } else { - if (config->enable_high) - cfg.ena_gpio_flags |= GPIOF_OUT_INIT_LOW; - else - cfg.ena_gpio_flags |= GPIOF_OUT_INIT_HIGH; - } + /* + * The signal will be inverted by the GPIO core if flagged so in the + * decriptor. + */ + if (config->enabled_at_boot) + gflags = GPIOD_OUT_HIGH | GPIOD_FLAGS_BIT_NONEXCLUSIVE; + else + gflags = GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE; + + cfg.ena_gpiod = gpiod_get_optional(dev, "enable", gflags); + if (IS_ERR(cfg.ena_gpiod)) + return PTR_ERR(cfg.ena_gpiod); drvdata->dev = regulator_register(&drvdata->desc, &cfg); if (IS_ERR(drvdata->dev)) { ret = PTR_ERR(drvdata->dev); - dev_err(&pdev->dev, "Failed to register regulator: %d\n", ret); - goto err_memstate; + dev_err(dev, "Failed to register regulator: %d\n", ret); + return ret; } platform_set_drvdata(pdev, drvdata); return 0; - -err_memstate: - kfree(drvdata->states); -err_stategpio: - gpio_free_array(drvdata->gpios, drvdata->nr_gpios); -err_memgpio: - kfree(drvdata->gpios); -err_name: - kfree(drvdata->desc.name); - return ret; } static int gpio_regulator_remove(struct platform_device *pdev) @@ -385,13 +344,6 @@ static int gpio_regulator_remove(struct platform_device *pdev) regulator_unregister(drvdata->dev); - gpio_free_array(drvdata->gpios, drvdata->nr_gpios); - - kfree(drvdata->states); - kfree(drvdata->gpios); - - kfree(drvdata->desc.name); - return 0; } diff --git a/drivers/regulator/helpers.c b/drivers/regulator/helpers.c index 5686a1335bd3..32d3f0499e2d 100644 --- a/drivers/regulator/helpers.c +++ b/drivers/regulator/helpers.c @@ -594,28 +594,30 @@ int regulator_list_voltage_pickable_linear_range(struct regulator_dev *rdev, EXPORT_SYMBOL_GPL(regulator_list_voltage_pickable_linear_range); /** - * regulator_list_voltage_linear_range - List voltages for linear ranges + * regulator_desc_list_voltage_linear_range - List voltages for linear ranges * - * @rdev: Regulator device + * @desc: Regulator desc for regulator which volatges are to be listed * @selector: Selector to convert into a voltage * * Regulators with a series of simple linear mappings between voltages - * and selectors can set linear_ranges in the regulator descriptor and - * then use this function as their list_voltage() operation, + * and selectors who have set linear_ranges in the regulator descriptor + * can use this function prior regulator registration to list voltages. + * This is useful when voltages need to be listed during device-tree + * parsing. */ -int regulator_list_voltage_linear_range(struct regulator_dev *rdev, - unsigned int selector) +int regulator_desc_list_voltage_linear_range(const struct regulator_desc *desc, + unsigned int selector) { const struct regulator_linear_range *range; int i; - if (!rdev->desc->n_linear_ranges) { - BUG_ON(!rdev->desc->n_linear_ranges); + if (!desc->n_linear_ranges) { + BUG_ON(!desc->n_linear_ranges); return -EINVAL; } - for (i = 0; i < rdev->desc->n_linear_ranges; i++) { - range = &rdev->desc->linear_ranges[i]; + for (i = 0; i < desc->n_linear_ranges; i++) { + range = &desc->linear_ranges[i]; if (!(selector >= range->min_sel && selector <= range->max_sel)) @@ -628,6 +630,23 @@ int regulator_list_voltage_linear_range(struct regulator_dev *rdev, return -EINVAL; } +EXPORT_SYMBOL_GPL(regulator_desc_list_voltage_linear_range); + +/** + * regulator_list_voltage_linear_range - List voltages for linear ranges + * + * @rdev: Regulator device + * @selector: Selector to convert into a voltage + * + * Regulators with a series of simple linear mappings between voltages + * and selectors can set linear_ranges in the regulator descriptor and + * then use this function as their list_voltage() operation, + */ +int regulator_list_voltage_linear_range(struct regulator_dev *rdev, + unsigned int selector) +{ + return regulator_desc_list_voltage_linear_range(rdev->desc, selector); +} EXPORT_SYMBOL_GPL(regulator_list_voltage_linear_range); /** @@ -761,3 +780,89 @@ int regulator_set_active_discharge_regmap(struct regulator_dev *rdev, rdev->desc->active_discharge_mask, val); } EXPORT_SYMBOL_GPL(regulator_set_active_discharge_regmap); + +/** + * regulator_set_current_limit_regmap - set_current_limit for regmap users + * + * @rdev: regulator to operate on + * @min_uA: Lower bound for current limit + * @max_uA: Upper bound for current limit + * + * Regulators that use regmap for their register I/O can set curr_table, + * csel_reg and csel_mask fields in their descriptor and then use this + * as their set_current_limit operation, saving some code. + */ +int regulator_set_current_limit_regmap(struct regulator_dev *rdev, + int min_uA, int max_uA) +{ + unsigned int n_currents = rdev->desc->n_current_limits; + int i, sel = -1; + + if (n_currents == 0) + return -EINVAL; + + if (rdev->desc->curr_table) { + const unsigned int *curr_table = rdev->desc->curr_table; + bool ascend = curr_table[n_currents - 1] > curr_table[0]; + + /* search for closest to maximum */ + if (ascend) { + for (i = n_currents - 1; i >= 0; i--) { + if (min_uA <= curr_table[i] && + curr_table[i] <= max_uA) { + sel = i; + break; + } + } + } else { + for (i = 0; i < n_currents; i++) { + if (min_uA <= curr_table[i] && + curr_table[i] <= max_uA) { + sel = i; + break; + } + } + } + } + + if (sel < 0) + return -EINVAL; + + sel <<= ffs(rdev->desc->csel_mask) - 1; + + return regmap_update_bits(rdev->regmap, rdev->desc->csel_reg, + rdev->desc->csel_mask, sel); +} +EXPORT_SYMBOL_GPL(regulator_set_current_limit_regmap); + +/** + * regulator_get_current_limit_regmap - get_current_limit for regmap users + * + * @rdev: regulator to operate on + * + * Regulators that use regmap for their register I/O can set the + * csel_reg and csel_mask fields in their descriptor and then use this + * as their get_current_limit operation, saving some code. + */ +int regulator_get_current_limit_regmap(struct regulator_dev *rdev) +{ + unsigned int val; + int ret; + + ret = regmap_read(rdev->regmap, rdev->desc->csel_reg, &val); + if (ret != 0) + return ret; + + val &= rdev->desc->csel_mask; + val >>= ffs(rdev->desc->csel_mask) - 1; + + if (rdev->desc->curr_table) { + if (val >= rdev->desc->n_current_limits) + return -EINVAL; + + return rdev->desc->curr_table[val]; + } + + return -EINVAL; +} +EXPORT_SYMBOL_GPL(regulator_get_current_limit_regmap); diff --git a/drivers/regulator/hi655x-regulator.c b/drivers/regulator/hi655x-regulator.c index 36ae54b53814..bba24a6fdb1e 100644 --- a/drivers/regulator/hi655x-regulator.c +++ b/drivers/regulator/hi655x-regulator.c @@ -28,7 +28,6 @@ struct hi655x_regulator { unsigned int disable_reg; unsigned int status_reg; - unsigned int ctrl_regs; unsigned int ctrl_mask; struct regulator_desc rdesc; }; diff --git a/drivers/regulator/isl6271a-regulator.c b/drivers/regulator/isl6271a-regulator.c index 4abd8e9c81e5..6f28bba81d13 100644 --- a/drivers/regulator/isl6271a-regulator.c +++ b/drivers/regulator/isl6271a-regulator.c @@ -31,7 +31,6 @@ /* PMIC details */ struct isl_pmic { struct i2c_client *client; - struct regulator_dev *rdev[3]; struct mutex mtx; }; @@ -66,14 +65,14 @@ static int isl6271a_set_voltage_sel(struct regulator_dev *dev, return err; } -static struct regulator_ops isl_core_ops = { +static const struct regulator_ops isl_core_ops = { .get_voltage_sel = isl6271a_get_voltage_sel, .set_voltage_sel = isl6271a_set_voltage_sel, .list_voltage = regulator_list_voltage_linear, .map_voltage = regulator_map_voltage_linear, }; -static struct regulator_ops isl_fixed_ops = { +static const struct regulator_ops isl_fixed_ops = { .list_voltage = regulator_list_voltage_linear, }; @@ -109,6 +108,7 @@ static const struct regulator_desc isl_rd[] = { static int isl6271a_probe(struct i2c_client *i2c, const struct i2c_device_id *id) { + struct regulator_dev *rdev; struct regulator_config config = { }; struct regulator_init_data *init_data = dev_get_platdata(&i2c->dev); struct isl_pmic *pmic; @@ -133,11 +133,10 @@ static int isl6271a_probe(struct i2c_client *i2c, config.init_data = NULL; config.driver_data = pmic; - pmic->rdev[i] = devm_regulator_register(&i2c->dev, &isl_rd[i], - &config); - if (IS_ERR(pmic->rdev[i])) { + rdev = devm_regulator_register(&i2c->dev, &isl_rd[i], &config); + if (IS_ERR(rdev)) { dev_err(&i2c->dev, "failed to register %s\n", id->name); - return PTR_ERR(pmic->rdev[i]); + return PTR_ERR(rdev); } } diff --git a/drivers/regulator/lm363x-regulator.c b/drivers/regulator/lm363x-regulator.c index 8c0e8419c43f..c876e161052a 100644 --- a/drivers/regulator/lm363x-regulator.c +++ b/drivers/regulator/lm363x-regulator.c @@ -258,6 +258,9 @@ static int lm363x_regulator_probe(struct platform_device *pdev) * Register update is required if the pin is used. */ gpiod = lm363x_regulator_of_get_enable_gpio(dev, id); + if (IS_ERR(gpiod)) + return PTR_ERR(gpiod); + if (gpiod) { cfg.ena_gpiod = gpiod; @@ -265,8 +268,7 @@ static int lm363x_regulator_probe(struct platform_device *pdev) LM3632_EXT_EN_MASK, LM3632_EXT_EN_MASK); if (ret) { - if (gpiod) - gpiod_put(gpiod); + gpiod_put(gpiod); dev_err(dev, "External pin err: %d\n", ret); return ret; } diff --git a/drivers/regulator/lochnagar-regulator.c b/drivers/regulator/lochnagar-regulator.c index 5a89e6d4b9a6..ff97cc50f2eb 100644 --- a/drivers/regulator/lochnagar-regulator.c +++ b/drivers/regulator/lochnagar-regulator.c @@ -194,7 +194,7 @@ static const struct regulator_desc lochnagar_regulators[] = { .name = "VDDCORE", .supply_name = "SYSVDD", .type = REGULATOR_VOLTAGE, - .n_voltages = 57, + .n_voltages = 66, .ops = &lochnagar_vddcore_ops, .id = LOCHNAGAR_VDDCORE, @@ -226,14 +226,15 @@ static const struct of_device_id lochnagar_of_match[] = { }, { .compatible = "cirrus,lochnagar2-mic2vdd", - .data = &lochnagar_regulators[LOCHNAGAR_MIC1VDD], + .data = &lochnagar_regulators[LOCHNAGAR_MIC2VDD], }, { .compatible = "cirrus,lochnagar2-vddcore", .data = &lochnagar_regulators[LOCHNAGAR_VDDCORE], }, - {}, + {} }; +MODULE_DEVICE_TABLE(of, lochnagar_of_match); static int lochnagar_regulator_probe(struct platform_device *pdev) { diff --git a/drivers/regulator/lp3971.c b/drivers/regulator/lp3971.c index 204b5c5270e0..9e45112658ba 100644 --- a/drivers/regulator/lp3971.c +++ b/drivers/regulator/lp3971.c @@ -159,7 +159,7 @@ static int lp3971_ldo_set_voltage_sel(struct regulator_dev *dev, selector << LDO_VOL_CONTR_SHIFT(ldo)); } -static struct regulator_ops lp3971_ldo_ops = { +static const struct regulator_ops lp3971_ldo_ops = { .list_voltage = regulator_list_voltage_table, .map_voltage = regulator_map_voltage_ascend, .is_enabled = lp3971_ldo_is_enabled, @@ -233,7 +233,7 @@ static int lp3971_dcdc_set_voltage_sel(struct regulator_dev *dev, 0 << BUCK_VOL_CHANGE_SHIFT(buck)); } -static struct regulator_ops lp3971_dcdc_ops = { +static const struct regulator_ops lp3971_dcdc_ops = { .list_voltage = regulator_list_voltage_table, .map_voltage = regulator_map_voltage_ascend, .is_enabled = lp3971_dcdc_is_enabled, diff --git a/drivers/regulator/lp3972.c b/drivers/regulator/lp3972.c index ff0c275f902e..fb098198b688 100644 --- a/drivers/regulator/lp3972.c +++ b/drivers/regulator/lp3972.c @@ -305,7 +305,7 @@ static int lp3972_ldo_set_voltage_sel(struct regulator_dev *dev, return ret; } -static struct regulator_ops lp3972_ldo_ops = { +static const struct regulator_ops lp3972_ldo_ops = { .list_voltage = regulator_list_voltage_table, .map_voltage = regulator_map_voltage_ascend, .is_enabled = lp3972_ldo_is_enabled, @@ -386,7 +386,7 @@ static int lp3972_dcdc_set_voltage_sel(struct regulator_dev *dev, LP3972_VOL_CHANGE_FLAG_MASK, 0); } -static struct regulator_ops lp3972_dcdc_ops = { +static const struct regulator_ops lp3972_dcdc_ops = { .list_voltage = regulator_list_voltage_table, .map_voltage = regulator_map_voltage_ascend, .is_enabled = lp3972_dcdc_is_enabled, diff --git a/drivers/regulator/lp872x.c b/drivers/regulator/lp872x.c index 38992112fd6e..ca95257ce252 100644 --- a/drivers/regulator/lp872x.c +++ b/drivers/regulator/lp872x.c @@ -353,64 +353,6 @@ static int lp872x_buck_get_voltage_sel(struct regulator_dev *rdev) return val & LP872X_VOUT_M; } -static int lp8725_buck_set_current_limit(struct regulator_dev *rdev, - int min_uA, int max_uA) -{ - struct lp872x *lp = rdev_get_drvdata(rdev); - enum lp872x_regulator_id buck = rdev_get_id(rdev); - int i; - u8 addr; - - switch (buck) { - case LP8725_ID_BUCK1: - addr = LP8725_BUCK1_VOUT2; - break; - case LP8725_ID_BUCK2: - addr = LP8725_BUCK2_VOUT2; - break; - default: - return -EINVAL; - } - - for (i = ARRAY_SIZE(lp8725_buck_uA) - 1; i >= 0; i--) { - if (lp8725_buck_uA[i] >= min_uA && - lp8725_buck_uA[i] <= max_uA) - return lp872x_update_bits(lp, addr, - LP8725_BUCK_CL_M, - i << LP8725_BUCK_CL_S); - } - - return -EINVAL; -} - -static int lp8725_buck_get_current_limit(struct regulator_dev *rdev) -{ - struct lp872x *lp = rdev_get_drvdata(rdev); - enum lp872x_regulator_id buck = rdev_get_id(rdev); - u8 addr, val; - int ret; - - switch (buck) { - case LP8725_ID_BUCK1: - addr = LP8725_BUCK1_VOUT2; - break; - case LP8725_ID_BUCK2: - addr = LP8725_BUCK2_VOUT2; - break; - default: - return -EINVAL; - } - - ret = lp872x_read_byte(lp, addr, &val); - if (ret) - return ret; - - val = (val & LP8725_BUCK_CL_M) >> LP8725_BUCK_CL_S; - - return (val < ARRAY_SIZE(lp8725_buck_uA)) ? - lp8725_buck_uA[val] : -EINVAL; -} - static int lp872x_buck_set_mode(struct regulator_dev *rdev, unsigned int mode) { struct lp872x *lp = rdev_get_drvdata(rdev); @@ -478,7 +420,7 @@ static unsigned int lp872x_buck_get_mode(struct regulator_dev *rdev) return val & mask ? REGULATOR_MODE_FAST : REGULATOR_MODE_NORMAL; } -static struct regulator_ops lp872x_ldo_ops = { +static const struct regulator_ops lp872x_ldo_ops = { .list_voltage = regulator_list_voltage_table, .map_voltage = regulator_map_voltage_ascend, .set_voltage_sel = regulator_set_voltage_sel_regmap, @@ -489,7 +431,7 @@ static struct regulator_ops lp872x_ldo_ops = { .enable_time = lp872x_regulator_enable_time, }; -static struct regulator_ops lp8720_buck_ops = { +static const struct regulator_ops lp8720_buck_ops = { .list_voltage = regulator_list_voltage_table, .map_voltage = regulator_map_voltage_ascend, .set_voltage_sel = lp872x_buck_set_voltage_sel, @@ -502,7 +444,7 @@ static struct regulator_ops lp8720_buck_ops = { .get_mode = lp872x_buck_get_mode, }; -static struct regulator_ops lp8725_buck_ops = { +static const struct regulator_ops lp8725_buck_ops = { .list_voltage = regulator_list_voltage_table, .map_voltage = regulator_map_voltage_ascend, .set_voltage_sel = lp872x_buck_set_voltage_sel, @@ -513,11 +455,11 @@ static struct regulator_ops lp8725_buck_ops = { .enable_time = lp872x_regulator_enable_time, .set_mode = lp872x_buck_set_mode, .get_mode = lp872x_buck_get_mode, - .set_current_limit = lp8725_buck_set_current_limit, - .get_current_limit = lp8725_buck_get_current_limit, + .set_current_limit = regulator_set_current_limit_regmap, + .get_current_limit = regulator_get_current_limit_regmap, }; -static struct regulator_desc lp8720_regulator_desc[] = { +static const struct regulator_desc lp8720_regulator_desc[] = { { .name = "ldo1", .of_match = of_match_ptr("ldo1"), @@ -602,7 +544,7 @@ static struct regulator_desc lp8720_regulator_desc[] = { }, }; -static struct regulator_desc lp8725_regulator_desc[] = { +static const struct regulator_desc lp8725_regulator_desc[] = { { .name = "ldo1", .of_match = of_match_ptr("ldo1"), @@ -712,6 +654,10 @@ static struct regulator_desc lp8725_regulator_desc[] = { .owner = THIS_MODULE, .enable_reg = LP872X_GENERAL_CFG, .enable_mask = LP8725_BUCK1_EN_M, + .curr_table = lp8725_buck_uA, + .n_current_limits = ARRAY_SIZE(lp8725_buck_uA), + .csel_reg = LP8725_BUCK1_VOUT2, + .csel_mask = LP8725_BUCK_CL_M, }, { .name = "buck2", @@ -724,6 +670,10 @@ static struct regulator_desc lp8725_regulator_desc[] = { .owner = THIS_MODULE, .enable_reg = LP872X_GENERAL_CFG, .enable_mask = LP8725_BUCK2_EN_M, + .curr_table = lp8725_buck_uA, + .n_current_limits = ARRAY_SIZE(lp8725_buck_uA), + .csel_reg = LP8725_BUCK2_VOUT2, + .csel_mask = LP8725_BUCK_CL_M, }, }; @@ -820,7 +770,7 @@ static struct regulator_init_data static int lp872x_regulator_register(struct lp872x *lp) { - struct regulator_desc *desc; + const struct regulator_desc *desc; struct regulator_config cfg = { }; struct regulator_dev *rdev; int i; diff --git a/drivers/regulator/lp873x-regulator.c b/drivers/regulator/lp873x-regulator.c index 70e3df653381..b55de293ca7a 100644 --- a/drivers/regulator/lp873x-regulator.c +++ b/drivers/regulator/lp873x-regulator.c @@ -39,6 +39,10 @@ .ramp_delay = _delay, \ .linear_ranges = _lr, \ .n_linear_ranges = ARRAY_SIZE(_lr), \ + .curr_table = lp873x_buck_uA, \ + .n_current_limits = ARRAY_SIZE(lp873x_buck_uA), \ + .csel_reg = (_cr), \ + .csel_mask = LP873X_BUCK0_CTRL_2_BUCK0_ILIM,\ }, \ .ctrl2_reg = _cr, \ } @@ -61,7 +65,7 @@ static const struct regulator_linear_range ldo0_ldo1_ranges[] = { REGULATOR_LINEAR_RANGE(800000, 0x0, 0x19, 100000), }; -static unsigned int lp873x_buck_ramp_delay[] = { +static const unsigned int lp873x_buck_ramp_delay[] = { 30000, 15000, 10000, 7500, 3800, 1900, 940, 470 }; @@ -108,45 +112,8 @@ static int lp873x_buck_set_ramp_delay(struct regulator_dev *rdev, return 0; } -static int lp873x_buck_set_current_limit(struct regulator_dev *rdev, - int min_uA, int max_uA) -{ - int id = rdev_get_id(rdev); - struct lp873x *lp873 = rdev_get_drvdata(rdev); - int i; - - for (i = ARRAY_SIZE(lp873x_buck_uA) - 1; i >= 0; i--) { - if (lp873x_buck_uA[i] >= min_uA && - lp873x_buck_uA[i] <= max_uA) - return regmap_update_bits(lp873->regmap, - regulators[id].ctrl2_reg, - LP873X_BUCK0_CTRL_2_BUCK0_ILIM, - i << __ffs(LP873X_BUCK0_CTRL_2_BUCK0_ILIM)); - } - - return -EINVAL; -} - -static int lp873x_buck_get_current_limit(struct regulator_dev *rdev) -{ - int id = rdev_get_id(rdev); - struct lp873x *lp873 = rdev_get_drvdata(rdev); - int ret; - unsigned int val; - - ret = regmap_read(lp873->regmap, regulators[id].ctrl2_reg, &val); - if (ret) - return ret; - - val = (val & LP873X_BUCK0_CTRL_2_BUCK0_ILIM) >> - __ffs(LP873X_BUCK0_CTRL_2_BUCK0_ILIM); - - return (val < ARRAY_SIZE(lp873x_buck_uA)) ? - lp873x_buck_uA[val] : -EINVAL; -} - /* Operations permitted on BUCK0, BUCK1 */ -static struct regulator_ops lp873x_buck01_ops = { +static const struct regulator_ops lp873x_buck01_ops = { .is_enabled = regulator_is_enabled_regmap, .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, @@ -156,12 +123,12 @@ static struct regulator_ops lp873x_buck01_ops = { .map_voltage = regulator_map_voltage_linear_range, .set_voltage_time_sel = regulator_set_voltage_time_sel, .set_ramp_delay = lp873x_buck_set_ramp_delay, - .set_current_limit = lp873x_buck_set_current_limit, - .get_current_limit = lp873x_buck_get_current_limit, + .set_current_limit = regulator_set_current_limit_regmap, + .get_current_limit = regulator_get_current_limit_regmap, }; /* Operations permitted on LDO0 and LDO1 */ -static struct regulator_ops lp873x_ldo01_ops = { +static const struct regulator_ops lp873x_ldo01_ops = { .is_enabled = regulator_is_enabled_regmap, .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, diff --git a/drivers/regulator/lp8755.c b/drivers/regulator/lp8755.c index 244822bb63cd..14fd38807134 100644 --- a/drivers/regulator/lp8755.c +++ b/drivers/regulator/lp8755.c @@ -315,7 +315,7 @@ out_i2c_error: .vsel_mask = LP8755_BUCK_VOUT_M,\ } -static struct regulator_desc lp8755_regulators[] = { +static const struct regulator_desc lp8755_regulators[] = { lp8755_buck_desc(0), lp8755_buck_desc(1), lp8755_buck_desc(2), @@ -386,7 +386,7 @@ static irqreturn_t lp8755_irq_handler(int irq, void *data) if (ret < 0) goto err_i2c; - /* send OCP event to all regualtor devices */ + /* send OCP event to all regulator devices */ if ((flag1 & 0x01) && (pchip->irqmask & 0x01)) for (icnt = 0; icnt < LP8755_BUCK_MAX; icnt++) if (pchip->rdev[icnt] != NULL) @@ -394,7 +394,7 @@ static irqreturn_t lp8755_irq_handler(int irq, void *data) LP8755_EVENT_OCP, NULL); - /* send OVP event to all regualtor devices */ + /* send OVP event to all regulator devices */ if ((flag1 & 0x02) && (pchip->irqmask & 0x02)) for (icnt = 0; icnt < LP8755_BUCK_MAX; icnt++) if (pchip->rdev[icnt] != NULL) diff --git a/drivers/regulator/lp87565-regulator.c b/drivers/regulator/lp87565-regulator.c index c192357d1dea..4ed41731a5b1 100644 --- a/drivers/regulator/lp87565-regulator.c +++ b/drivers/regulator/lp87565-regulator.c @@ -51,7 +51,7 @@ static const struct regulator_linear_range buck0_1_2_3_ranges[] = { REGULATOR_LINEAR_RANGE(1420000, 0x9e, 0xff, 20000), }; -static unsigned int lp87565_buck_ramp_delay[] = { +static const unsigned int lp87565_buck_ramp_delay[] = { 30000, 15000, 10000, 7500, 3800, 1900, 940, 470 }; @@ -140,7 +140,7 @@ static int lp87565_buck_get_current_limit(struct regulator_dev *rdev) } /* Operations permitted on BUCK0, BUCK1 */ -static struct regulator_ops lp87565_buck_ops = { +static const struct regulator_ops lp87565_buck_ops = { .is_enabled = regulator_is_enabled_regmap, .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, diff --git a/drivers/regulator/lp8788-buck.c b/drivers/regulator/lp8788-buck.c index ec46290b647e..a7d30550bb5f 100644 --- a/drivers/regulator/lp8788-buck.c +++ b/drivers/regulator/lp8788-buck.c @@ -95,12 +95,10 @@ struct lp8788_buck { void *dvs; }; -/* BUCK 1 ~ 4 voltage table */ -static const int lp8788_buck_vtbl[] = { - 500000, 800000, 850000, 900000, 950000, 1000000, 1050000, 1100000, - 1150000, 1200000, 1250000, 1300000, 1350000, 1400000, 1450000, 1500000, - 1550000, 1600000, 1650000, 1700000, 1750000, 1800000, 1850000, 1900000, - 1950000, 2000000, +/* BUCK 1 ~ 4 voltage ranges */ +static const struct regulator_linear_range buck_volt_ranges[] = { + REGULATOR_LINEAR_RANGE(500000, 0, 0, 0), + REGULATOR_LINEAR_RANGE(800000, 1, 25, 50000), }; static void lp8788_buck1_set_dvs(struct lp8788_buck *buck) @@ -345,8 +343,8 @@ static unsigned int lp8788_buck_get_mode(struct regulator_dev *rdev) } static const struct regulator_ops lp8788_buck12_ops = { - .list_voltage = regulator_list_voltage_table, - .map_voltage = regulator_map_voltage_ascend, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, .set_voltage_sel = lp8788_buck12_set_voltage_sel, .get_voltage_sel = lp8788_buck12_get_voltage_sel, .enable = regulator_enable_regmap, @@ -358,8 +356,8 @@ static const struct regulator_ops lp8788_buck12_ops = { }; static const struct regulator_ops lp8788_buck34_ops = { - .list_voltage = regulator_list_voltage_table, - .map_voltage = regulator_map_voltage_ascend, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, .set_voltage_sel = regulator_set_voltage_sel_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, .enable = regulator_enable_regmap, @@ -370,13 +368,14 @@ static const struct regulator_ops lp8788_buck34_ops = { .get_mode = lp8788_buck_get_mode, }; -static struct regulator_desc lp8788_buck_desc[] = { +static const struct regulator_desc lp8788_buck_desc[] = { { .name = "buck1", .id = BUCK1, .ops = &lp8788_buck12_ops, - .n_voltages = ARRAY_SIZE(lp8788_buck_vtbl), - .volt_table = lp8788_buck_vtbl, + .n_voltages = 26, + .linear_ranges = buck_volt_ranges, + .n_linear_ranges = ARRAY_SIZE(buck_volt_ranges), .type = REGULATOR_VOLTAGE, .owner = THIS_MODULE, .enable_reg = LP8788_EN_BUCK, @@ -386,8 +385,9 @@ static struct regulator_desc lp8788_buck_desc[] = { .name = "buck2", .id = BUCK2, .ops = &lp8788_buck12_ops, - .n_voltages = ARRAY_SIZE(lp8788_buck_vtbl), - .volt_table = lp8788_buck_vtbl, + .n_voltages = 26, + .linear_ranges = buck_volt_ranges, + .n_linear_ranges = ARRAY_SIZE(buck_volt_ranges), .type = REGULATOR_VOLTAGE, .owner = THIS_MODULE, .enable_reg = LP8788_EN_BUCK, @@ -397,8 +397,9 @@ static struct regulator_desc lp8788_buck_desc[] = { .name = "buck3", .id = BUCK3, .ops = &lp8788_buck34_ops, - .n_voltages = ARRAY_SIZE(lp8788_buck_vtbl), - .volt_table = lp8788_buck_vtbl, + .n_voltages = 26, + .linear_ranges = buck_volt_ranges, + .n_linear_ranges = ARRAY_SIZE(buck_volt_ranges), .type = REGULATOR_VOLTAGE, .owner = THIS_MODULE, .vsel_reg = LP8788_BUCK3_VOUT, @@ -410,8 +411,9 @@ static struct regulator_desc lp8788_buck_desc[] = { .name = "buck4", .id = BUCK4, .ops = &lp8788_buck34_ops, - .n_voltages = ARRAY_SIZE(lp8788_buck_vtbl), - .volt_table = lp8788_buck_vtbl, + .n_voltages = 26, + .linear_ranges = buck_volt_ranges, + .n_linear_ranges = ARRAY_SIZE(buck_volt_ranges), .type = REGULATOR_VOLTAGE, .owner = THIS_MODULE, .vsel_reg = LP8788_BUCK4_VOUT, diff --git a/drivers/regulator/lp8788-ldo.c b/drivers/regulator/lp8788-ldo.c index 2ee22e7ea675..a2ef146e6b3a 100644 --- a/drivers/regulator/lp8788-ldo.c +++ b/drivers/regulator/lp8788-ldo.c @@ -186,7 +186,7 @@ static const struct regulator_ops lp8788_ldo_voltage_fixed_ops = { .enable_time = lp8788_ldo_enable_time, }; -static struct regulator_desc lp8788_dldo_desc[] = { +static const struct regulator_desc lp8788_dldo_desc[] = { { .name = "dldo1", .id = DLDO1, @@ -343,7 +343,7 @@ static struct regulator_desc lp8788_dldo_desc[] = { }, }; -static struct regulator_desc lp8788_aldo_desc[] = { +static const struct regulator_desc lp8788_aldo_desc[] = { { .name = "aldo1", .id = ALDO1, diff --git a/drivers/regulator/ltc3676.c b/drivers/regulator/ltc3676.c index 71fd0f2a4b76..e6d66e492b85 100644 --- a/drivers/regulator/ltc3676.c +++ b/drivers/regulator/ltc3676.c @@ -241,61 +241,10 @@ static struct regulator_desc ltc3676_regulators[LTC3676_NUM_REGULATORS] = { LTC3676_FIXED_REG(LDO4, ldo4, LDOB, 2), }; -static bool ltc3676_writeable_reg(struct device *dev, unsigned int reg) +static bool ltc3676_readable_writeable_reg(struct device *dev, unsigned int reg) { switch (reg) { - case LTC3676_IRQSTAT: - case LTC3676_BUCK1: - case LTC3676_BUCK2: - case LTC3676_BUCK3: - case LTC3676_BUCK4: - case LTC3676_LDOA: - case LTC3676_LDOB: - case LTC3676_SQD1: - case LTC3676_SQD2: - case LTC3676_CNTRL: - case LTC3676_DVB1A: - case LTC3676_DVB1B: - case LTC3676_DVB2A: - case LTC3676_DVB2B: - case LTC3676_DVB3A: - case LTC3676_DVB3B: - case LTC3676_DVB4A: - case LTC3676_DVB4B: - case LTC3676_MSKIRQ: - case LTC3676_MSKPG: - case LTC3676_USER: - case LTC3676_HRST: - case LTC3676_CLIRQ: - return true; - } - return false; -} - -static bool ltc3676_readable_reg(struct device *dev, unsigned int reg) -{ - switch (reg) { - case LTC3676_IRQSTAT: - case LTC3676_BUCK1: - case LTC3676_BUCK2: - case LTC3676_BUCK3: - case LTC3676_BUCK4: - case LTC3676_LDOA: - case LTC3676_LDOB: - case LTC3676_SQD1: - case LTC3676_SQD2: - case LTC3676_CNTRL: - case LTC3676_DVB1A: - case LTC3676_DVB1B: - case LTC3676_DVB2A: - case LTC3676_DVB2B: - case LTC3676_DVB3A: - case LTC3676_DVB3B: - case LTC3676_DVB4A: - case LTC3676_DVB4B: - case LTC3676_MSKIRQ: - case LTC3676_MSKPG: - case LTC3676_USER: + case LTC3676_BUCK1 ... LTC3676_IRQSTAT: case LTC3676_HRST: case LTC3676_CLIRQ: return true; @@ -306,9 +255,7 @@ static bool ltc3676_readable_reg(struct device *dev, unsigned int reg) static bool ltc3676_volatile_reg(struct device *dev, unsigned int reg) { switch (reg) { - case LTC3676_IRQSTAT: - case LTC3676_PGSTATL: - case LTC3676_PGSTATRT: + case LTC3676_IRQSTAT ... LTC3676_PGSTATRT: return true; } return false; @@ -317,8 +264,8 @@ static bool ltc3676_volatile_reg(struct device *dev, unsigned int reg) static const struct regmap_config ltc3676_regmap_config = { .reg_bits = 8, .val_bits = 8, - .writeable_reg = ltc3676_writeable_reg, - .readable_reg = ltc3676_readable_reg, + .writeable_reg = ltc3676_readable_writeable_reg, + .readable_reg = ltc3676_readable_writeable_reg, .volatile_reg = ltc3676_volatile_reg, .max_register = LTC3676_CLIRQ, .use_single_read = true, @@ -442,5 +389,5 @@ static struct i2c_driver ltc3676_driver = { module_i2c_driver(ltc3676_driver); MODULE_AUTHOR("Tim Harvey <tharvey@gateworks.com>"); -MODULE_DESCRIPTION("Regulator driver for Linear Technology LTC1376"); +MODULE_DESCRIPTION("Regulator driver for Linear Technology LTC3676"); MODULE_LICENSE("GPL v2"); diff --git a/drivers/regulator/max14577-regulator.c b/drivers/regulator/max14577-regulator.c index bc7f4751bf9c..85a88a9e4d42 100644 --- a/drivers/regulator/max14577-regulator.c +++ b/drivers/regulator/max14577-regulator.c @@ -324,4 +324,3 @@ module_exit(max14577_regulator_exit); MODULE_AUTHOR("Krzysztof Kozlowski <krzk@kernel.org>"); MODULE_DESCRIPTION("Maxim 14577/77836 regulator driver"); MODULE_LICENSE("GPL"); -MODULE_ALIAS("platform:max14577-regulator"); diff --git a/drivers/regulator/max77620-regulator.c b/drivers/regulator/max77620-regulator.c index b94e3a721721..1607ac673e44 100644 --- a/drivers/regulator/max77620-regulator.c +++ b/drivers/regulator/max77620-regulator.c @@ -1,7 +1,7 @@ /* * Maxim MAX77620 Regulator driver * - * Copyright (c) 2016, NVIDIA CORPORATION. All rights reserved. + * Copyright (c) 2016-2018, NVIDIA CORPORATION. All rights reserved. * * Author: Mallikarjun Kasoju <mkasoju@nvidia.com> * Laxman Dewangan <ldewangan@nvidia.com> @@ -690,6 +690,7 @@ static const struct regulator_ops max77620_regulator_ops = { .active_discharge_mask = MAX77620_SD_CFG1_ADE_MASK, \ .active_discharge_reg = MAX77620_REG_##_id##_CFG, \ .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ }, \ } @@ -721,6 +722,7 @@ static const struct regulator_ops max77620_regulator_ops = { .active_discharge_mask = MAX77620_LDO_CFG2_ADE_MASK, \ .active_discharge_reg = MAX77620_REG_##_id##_CFG2, \ .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ }, \ } @@ -803,6 +805,14 @@ static int max77620_regulator_probe(struct platform_device *pdev) rdesc = &rinfo[id].desc; pmic->rinfo[id] = &max77620_regs_info[id]; pmic->enable_power_mode[id] = MAX77620_POWER_MODE_NORMAL; + pmic->reg_pdata[id].active_fps_src = -1; + pmic->reg_pdata[id].active_fps_pd_slot = -1; + pmic->reg_pdata[id].active_fps_pu_slot = -1; + pmic->reg_pdata[id].suspend_fps_src = -1; + pmic->reg_pdata[id].suspend_fps_pd_slot = -1; + pmic->reg_pdata[id].suspend_fps_pu_slot = -1; + pmic->reg_pdata[id].power_ok = -1; + pmic->reg_pdata[id].ramp_rate_setting = -1; ret = max77620_read_slew_rate(pmic, id); if (ret < 0) diff --git a/drivers/regulator/max77650-regulator.c b/drivers/regulator/max77650-regulator.c new file mode 100644 index 000000000000..31ebf34b01ec --- /dev/null +++ b/drivers/regulator/max77650-regulator.c @@ -0,0 +1,498 @@ +// SPDX-License-Identifier: GPL-2.0 +// +// Copyright (C) 2018 BayLibre SAS +// Author: Bartosz Golaszewski <bgolaszewski@baylibre.com> +// +// Regulator driver for MAXIM 77650/77651 charger/power-supply. + +#include <linux/of.h> +#include <linux/mfd/max77650.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/regulator/driver.h> + +#define MAX77650_REGULATOR_EN_CTRL_MASK GENMASK(3, 0) +#define MAX77650_REGULATOR_EN_CTRL_BITS(_reg) \ + ((_reg) & MAX77650_REGULATOR_EN_CTRL_MASK) +#define MAX77650_REGULATOR_ENABLED GENMASK(2, 1) +#define MAX77650_REGULATOR_DISABLED BIT(2) + +#define MAX77650_REGULATOR_V_LDO_MASK GENMASK(6, 0) +#define MAX77650_REGULATOR_V_SBB_MASK GENMASK(5, 0) + +#define MAX77650_REGULATOR_AD_MASK BIT(3) +#define MAX77650_REGULATOR_AD_DISABLED 0x00 +#define MAX77650_REGULATOR_AD_ENABLED BIT(3) + +#define MAX77650_REGULATOR_CURR_LIM_MASK GENMASK(7, 6) + +enum { + MAX77650_REGULATOR_ID_LDO = 0, + MAX77650_REGULATOR_ID_SBB0, + MAX77650_REGULATOR_ID_SBB1, + MAX77650_REGULATOR_ID_SBB2, + MAX77650_REGULATOR_NUM_REGULATORS, +}; + +struct max77650_regulator_desc { + struct regulator_desc desc; + unsigned int regA; + unsigned int regB; +}; + +static const u32 max77651_sbb1_regulator_volt_table[] = { + 2400000, 3200000, 4000000, 4800000, + 2450000, 3250000, 4050000, 4850000, + 2500000, 3300000, 4100000, 4900000, + 2550000, 3350000, 4150000, 4950000, + 2600000, 3400000, 4200000, 5000000, + 2650000, 3450000, 4250000, 5050000, + 2700000, 3500000, 4300000, 5100000, + 2750000, 3550000, 4350000, 5150000, + 2800000, 3600000, 4400000, 5200000, + 2850000, 3650000, 4450000, 5250000, + 2900000, 3700000, 4500000, 0, + 2950000, 3750000, 4550000, 0, + 3000000, 3800000, 4600000, 0, + 3050000, 3850000, 4650000, 0, + 3100000, 3900000, 4700000, 0, + 3150000, 3950000, 4750000, 0, +}; + +#define MAX77651_REGULATOR_SBB1_SEL_DEC(_val) \ + (((_val & 0x3c) >> 2) | ((_val & 0x03) << 4)) +#define MAX77651_REGULATOR_SBB1_SEL_ENC(_val) \ + (((_val & 0x30) >> 4) | ((_val & 0x0f) << 2)) + +#define MAX77650_REGULATOR_SBB1_SEL_DECR(_val) \ + do { \ + _val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val); \ + _val--; \ + _val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val); \ + } while (0) + +#define MAX77650_REGULATOR_SBB1_SEL_INCR(_val) \ + do { \ + _val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val); \ + _val++; \ + _val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val); \ + } while (0) + +static const unsigned int max77650_current_limit_table[] = { + 1000000, 866000, 707000, 500000, +}; + +static int max77650_regulator_is_enabled(struct regulator_dev *rdev) +{ + struct max77650_regulator_desc *rdesc; + struct regmap *map; + int val, rv, en; + + rdesc = rdev_get_drvdata(rdev); + map = rdev_get_regmap(rdev); + + rv = regmap_read(map, rdesc->regB, &val); + if (rv) + return rv; + + en = MAX77650_REGULATOR_EN_CTRL_BITS(val); + + return en != MAX77650_REGULATOR_DISABLED; +} + +static int max77650_regulator_enable(struct regulator_dev *rdev) +{ + struct max77650_regulator_desc *rdesc; + struct regmap *map; + + rdesc = rdev_get_drvdata(rdev); + map = rdev_get_regmap(rdev); + + return regmap_update_bits(map, rdesc->regB, + MAX77650_REGULATOR_EN_CTRL_MASK, + MAX77650_REGULATOR_ENABLED); +} + +static int max77650_regulator_disable(struct regulator_dev *rdev) +{ + struct max77650_regulator_desc *rdesc; + struct regmap *map; + + rdesc = rdev_get_drvdata(rdev); + map = rdev_get_regmap(rdev); + + return regmap_update_bits(map, rdesc->regB, + MAX77650_REGULATOR_EN_CTRL_MASK, + MAX77650_REGULATOR_DISABLED); +} + +static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev, + unsigned int sel) +{ + int rv = 0, curr, diff; + bool ascending; + + /* + * If the regulator is disabled, we can program the desired + * voltage right away. + */ + if (!max77650_regulator_is_enabled(rdev)) + return regulator_set_voltage_sel_regmap(rdev, sel); + + /* + * Otherwise we need to manually ramp the output voltage up/down + * one step at a time. + */ + + curr = regulator_get_voltage_sel_regmap(rdev); + if (curr < 0) + return curr; + + diff = curr - sel; + if (diff == 0) + return 0; /* Already there. */ + else if (diff > 0) + ascending = false; + else + ascending = true; + + /* + * Make sure we'll get to the right voltage and break the loop even if + * the selector equals 0. + */ + for (ascending ? curr++ : curr--;; ascending ? curr++ : curr--) { + rv = regulator_set_voltage_sel_regmap(rdev, curr); + if (rv) + return rv; + + if (curr == sel) + break; + } + + return 0; +} + +/* + * Special case: non-linear voltage table for max77651 SBB1 - software + * must ensure the voltage is ramped in 50mV increments. + */ +static int max77651_regulator_sbb1_set_voltage_sel(struct regulator_dev *rdev, + unsigned int sel) +{ + int rv = 0, curr, vcurr, vdest, vdiff; + + /* + * If the regulator is disabled, we can program the desired + * voltage right away. + */ + if (!max77650_regulator_is_enabled(rdev)) + return regulator_set_voltage_sel_regmap(rdev, sel); + + curr = regulator_get_voltage_sel_regmap(rdev); + if (curr < 0) + return curr; + + if (curr == sel) + return 0; /* Already there. */ + + vcurr = max77651_sbb1_regulator_volt_table[curr]; + vdest = max77651_sbb1_regulator_volt_table[sel]; + vdiff = vcurr - vdest; + + for (;;) { + if (vdiff > 0) + MAX77650_REGULATOR_SBB1_SEL_DECR(curr); + else + MAX77650_REGULATOR_SBB1_SEL_INCR(curr); + + rv = regulator_set_voltage_sel_regmap(rdev, curr); + if (rv) + return rv; + + if (curr == sel) + break; + }; + + return 0; +} + +static const struct regulator_ops max77650_regulator_LDO_ops = { + .is_enabled = max77650_regulator_is_enabled, + .enable = max77650_regulator_enable, + .disable = max77650_regulator_disable, + .list_voltage = regulator_list_voltage_linear, + .map_voltage = regulator_map_voltage_linear, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = max77650_regulator_set_voltage_sel, + .set_active_discharge = regulator_set_active_discharge_regmap, +}; + +static const struct regulator_ops max77650_regulator_SBB_ops = { + .is_enabled = max77650_regulator_is_enabled, + .enable = max77650_regulator_enable, + .disable = max77650_regulator_disable, + .list_voltage = regulator_list_voltage_linear, + .map_voltage = regulator_map_voltage_linear, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = max77650_regulator_set_voltage_sel, + .get_current_limit = regulator_get_current_limit_regmap, + .set_current_limit = regulator_set_current_limit_regmap, + .set_active_discharge = regulator_set_active_discharge_regmap, +}; + +/* Special case for max77651 SBB1 - non-linear voltage mapping. */ +static const struct regulator_ops max77651_SBB1_regulator_ops = { + .is_enabled = max77650_regulator_is_enabled, + .enable = max77650_regulator_enable, + .disable = max77650_regulator_disable, + .list_voltage = regulator_list_voltage_table, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = max77651_regulator_sbb1_set_voltage_sel, + .get_current_limit = regulator_get_current_limit_regmap, + .set_current_limit = regulator_set_current_limit_regmap, + .set_active_discharge = regulator_set_active_discharge_regmap, +}; + +static struct max77650_regulator_desc max77650_LDO_desc = { + .desc = { + .name = "ldo", + .of_match = of_match_ptr("ldo"), + .regulators_node = of_match_ptr("regulators"), + .supply_name = "in-ldo", + .id = MAX77650_REGULATOR_ID_LDO, + .ops = &max77650_regulator_LDO_ops, + .min_uV = 1350000, + .uV_step = 12500, + .n_voltages = 128, + .vsel_mask = MAX77650_REGULATOR_V_LDO_MASK, + .vsel_reg = MAX77650_REG_CNFG_LDO_A, + .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED, + .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED, + .active_discharge_mask = MAX77650_REGULATOR_AD_MASK, + .active_discharge_reg = MAX77650_REG_CNFG_LDO_B, + .enable_time = 100, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, + }, + .regA = MAX77650_REG_CNFG_LDO_A, + .regB = MAX77650_REG_CNFG_LDO_B, +}; + +static struct max77650_regulator_desc max77650_SBB0_desc = { + .desc = { + .name = "sbb0", + .of_match = of_match_ptr("sbb0"), + .regulators_node = of_match_ptr("regulators"), + .supply_name = "in-sbb0", + .id = MAX77650_REGULATOR_ID_SBB0, + .ops = &max77650_regulator_SBB_ops, + .min_uV = 800000, + .uV_step = 25000, + .n_voltages = 64, + .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK, + .vsel_reg = MAX77650_REG_CNFG_SBB0_A, + .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED, + .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED, + .active_discharge_mask = MAX77650_REGULATOR_AD_MASK, + .active_discharge_reg = MAX77650_REG_CNFG_SBB0_B, + .enable_time = 100, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, + .csel_reg = MAX77650_REG_CNFG_SBB0_A, + .csel_mask = MAX77650_REGULATOR_CURR_LIM_MASK, + .curr_table = max77650_current_limit_table, + .n_current_limits = ARRAY_SIZE(max77650_current_limit_table), + }, + .regA = MAX77650_REG_CNFG_SBB0_A, + .regB = MAX77650_REG_CNFG_SBB0_B, +}; + +static struct max77650_regulator_desc max77650_SBB1_desc = { + .desc = { + .name = "sbb1", + .of_match = of_match_ptr("sbb1"), + .regulators_node = of_match_ptr("regulators"), + .supply_name = "in-sbb1", + .id = MAX77650_REGULATOR_ID_SBB1, + .ops = &max77650_regulator_SBB_ops, + .min_uV = 800000, + .uV_step = 12500, + .n_voltages = 64, + .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK, + .vsel_reg = MAX77650_REG_CNFG_SBB1_A, + .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED, + .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED, + .active_discharge_mask = MAX77650_REGULATOR_AD_MASK, + .active_discharge_reg = MAX77650_REG_CNFG_SBB1_B, + .enable_time = 100, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, + .csel_reg = MAX77650_REG_CNFG_SBB1_A, + .csel_mask = MAX77650_REGULATOR_CURR_LIM_MASK, + .curr_table = max77650_current_limit_table, + .n_current_limits = ARRAY_SIZE(max77650_current_limit_table), + }, + .regA = MAX77650_REG_CNFG_SBB1_A, + .regB = MAX77650_REG_CNFG_SBB1_B, +}; + +static struct max77650_regulator_desc max77651_SBB1_desc = { + .desc = { + .name = "sbb1", + .of_match = of_match_ptr("sbb1"), + .regulators_node = of_match_ptr("regulators"), + .supply_name = "in-sbb1", + .id = MAX77650_REGULATOR_ID_SBB1, + .ops = &max77651_SBB1_regulator_ops, + .volt_table = max77651_sbb1_regulator_volt_table, + .n_voltages = ARRAY_SIZE(max77651_sbb1_regulator_volt_table), + .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK, + .vsel_reg = MAX77650_REG_CNFG_SBB1_A, + .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED, + .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED, + .active_discharge_mask = MAX77650_REGULATOR_AD_MASK, + .active_discharge_reg = MAX77650_REG_CNFG_SBB1_B, + .enable_time = 100, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, + .csel_reg = MAX77650_REG_CNFG_SBB1_A, + .csel_mask = MAX77650_REGULATOR_CURR_LIM_MASK, + .curr_table = max77650_current_limit_table, + .n_current_limits = ARRAY_SIZE(max77650_current_limit_table), + }, + .regA = MAX77650_REG_CNFG_SBB1_A, + .regB = MAX77650_REG_CNFG_SBB1_B, +}; + +static struct max77650_regulator_desc max77650_SBB2_desc = { + .desc = { + .name = "sbb2", + .of_match = of_match_ptr("sbb2"), + .regulators_node = of_match_ptr("regulators"), + .supply_name = "in-sbb0", + .id = MAX77650_REGULATOR_ID_SBB2, + .ops = &max77650_regulator_SBB_ops, + .min_uV = 800000, + .uV_step = 50000, + .n_voltages = 64, + .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK, + .vsel_reg = MAX77650_REG_CNFG_SBB2_A, + .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED, + .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED, + .active_discharge_mask = MAX77650_REGULATOR_AD_MASK, + .active_discharge_reg = MAX77650_REG_CNFG_SBB2_B, + .enable_time = 100, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, + .csel_reg = MAX77650_REG_CNFG_SBB2_A, + .csel_mask = MAX77650_REGULATOR_CURR_LIM_MASK, + .curr_table = max77650_current_limit_table, + .n_current_limits = ARRAY_SIZE(max77650_current_limit_table), + }, + .regA = MAX77650_REG_CNFG_SBB2_A, + .regB = MAX77650_REG_CNFG_SBB2_B, +}; + +static struct max77650_regulator_desc max77651_SBB2_desc = { + .desc = { + .name = "sbb2", + .of_match = of_match_ptr("sbb2"), + .regulators_node = of_match_ptr("regulators"), + .supply_name = "in-sbb0", + .id = MAX77650_REGULATOR_ID_SBB2, + .ops = &max77650_regulator_SBB_ops, + .min_uV = 2400000, + .uV_step = 50000, + .n_voltages = 64, + .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK, + .vsel_reg = MAX77650_REG_CNFG_SBB2_A, + .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED, + .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED, + .active_discharge_mask = MAX77650_REGULATOR_AD_MASK, + .active_discharge_reg = MAX77650_REG_CNFG_SBB2_B, + .enable_time = 100, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, + .csel_reg = MAX77650_REG_CNFG_SBB2_A, + .csel_mask = MAX77650_REGULATOR_CURR_LIM_MASK, + .curr_table = max77650_current_limit_table, + .n_current_limits = ARRAY_SIZE(max77650_current_limit_table), + }, + .regA = MAX77650_REG_CNFG_SBB2_A, + .regB = MAX77650_REG_CNFG_SBB2_B, +}; + +static int max77650_regulator_probe(struct platform_device *pdev) +{ + struct max77650_regulator_desc **rdescs; + struct max77650_regulator_desc *rdesc; + struct regulator_config config = { }; + struct device *dev, *parent; + struct regulator_dev *rdev; + struct regmap *map; + unsigned int val; + int i, rv; + + dev = &pdev->dev; + parent = dev->parent; + + if (!dev->of_node) + dev->of_node = parent->of_node; + + rdescs = devm_kcalloc(dev, MAX77650_REGULATOR_NUM_REGULATORS, + sizeof(*rdescs), GFP_KERNEL); + if (!rdescs) + return -ENOMEM; + + map = dev_get_regmap(parent, NULL); + if (!map) + return -ENODEV; + + rv = regmap_read(map, MAX77650_REG_CID, &val); + if (rv) + return rv; + + rdescs[MAX77650_REGULATOR_ID_LDO] = &max77650_LDO_desc; + rdescs[MAX77650_REGULATOR_ID_SBB0] = &max77650_SBB0_desc; + + switch (MAX77650_CID_BITS(val)) { + case MAX77650_CID_77650A: + case MAX77650_CID_77650C: + rdescs[MAX77650_REGULATOR_ID_SBB1] = &max77650_SBB1_desc; + rdescs[MAX77650_REGULATOR_ID_SBB2] = &max77650_SBB2_desc; + break; + case MAX77650_CID_77651A: + case MAX77650_CID_77651B: + rdescs[MAX77650_REGULATOR_ID_SBB1] = &max77651_SBB1_desc; + rdescs[MAX77650_REGULATOR_ID_SBB2] = &max77651_SBB2_desc; + break; + default: + return -ENODEV; + } + + config.dev = parent; + + for (i = 0; i < MAX77650_REGULATOR_NUM_REGULATORS; i++) { + rdesc = rdescs[i]; + config.driver_data = rdesc; + + rdev = devm_regulator_register(dev, &rdesc->desc, &config); + if (IS_ERR(rdev)) + return PTR_ERR(rdev); + } + + return 0; +} + +static struct platform_driver max77650_regulator_driver = { + .driver = { + .name = "max77650-regulator", + }, + .probe = max77650_regulator_probe, +}; +module_platform_driver(max77650_regulator_driver); + +MODULE_DESCRIPTION("MAXIM 77650/77651 regulator driver"); +MODULE_AUTHOR("Bartosz Golaszewski <bgolaszewski@baylibre.com>"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/regulator/max77802-regulator.c b/drivers/regulator/max77802-regulator.c index c30cf5c9f2de..ea7b50397300 100644 --- a/drivers/regulator/max77802-regulator.c +++ b/drivers/regulator/max77802-regulator.c @@ -248,9 +248,9 @@ static int max77802_set_ramp_delay_2bit(struct regulator_dev *rdev, unsigned int ramp_value; if (id > MAX77802_BUCK4) { - dev_warn(&rdev->dev, - "%s: regulator: ramp delay not supported\n", - rdev->desc->name); + dev_warn(&rdev->dev, + "%s: regulator: ramp delay not supported\n", + rdev->desc->name); return -EINVAL; } ramp_value = max77802_find_ramp_value(rdev, ramp_table_77802_2bit, diff --git a/drivers/regulator/mc13783-regulator.c b/drivers/regulator/mc13783-regulator.c index 8fd1adc9c9a9..ab558b26cd7c 100644 --- a/drivers/regulator/mc13783-regulator.c +++ b/drivers/regulator/mc13783-regulator.c @@ -226,69 +226,69 @@ static const unsigned int mc13783_pwgtdrv_val[] = { 5500000, }; -static struct regulator_ops mc13783_gpo_regulator_ops; +static const struct regulator_ops mc13783_gpo_regulator_ops; -#define MC13783_DEFINE(prefix, name, reg, vsel_reg, voltages) \ - MC13xxx_DEFINE(MC13783_REG_, name, reg, vsel_reg, voltages, \ +#define MC13783_DEFINE(prefix, name, node, reg, vsel_reg, voltages) \ + MC13xxx_DEFINE(MC13783_REG_, name, node, reg, vsel_reg, voltages, \ mc13xxx_regulator_ops) -#define MC13783_FIXED_DEFINE(prefix, name, reg, voltages) \ - MC13xxx_FIXED_DEFINE(MC13783_REG_, name, reg, voltages, \ +#define MC13783_FIXED_DEFINE(prefix, name, node, reg, voltages) \ + MC13xxx_FIXED_DEFINE(MC13783_REG_, name, node, reg, voltages, \ mc13xxx_fixed_regulator_ops) -#define MC13783_GPO_DEFINE(prefix, name, reg, voltages) \ - MC13xxx_GPO_DEFINE(MC13783_REG_, name, reg, voltages, \ +#define MC13783_GPO_DEFINE(prefix, name, node, reg, voltages) \ + MC13xxx_GPO_DEFINE(MC13783_REG_, name, node, reg, voltages, \ mc13783_gpo_regulator_ops) -#define MC13783_DEFINE_SW(_name, _reg, _vsel_reg, _voltages) \ - MC13783_DEFINE(REG, _name, _reg, _vsel_reg, _voltages) -#define MC13783_DEFINE_REGU(_name, _reg, _vsel_reg, _voltages) \ - MC13783_DEFINE(REG, _name, _reg, _vsel_reg, _voltages) +#define MC13783_DEFINE_SW(_name, _node, _reg, _vsel_reg, _voltages) \ + MC13783_DEFINE(REG, _name, _node, _reg, _vsel_reg, _voltages) +#define MC13783_DEFINE_REGU(_name, _node, _reg, _vsel_reg, _voltages) \ + MC13783_DEFINE(REG, _name, _node, _reg, _vsel_reg, _voltages) static struct mc13xxx_regulator mc13783_regulators[] = { - MC13783_DEFINE_SW(SW1A, SWITCHERS0, SWITCHERS0, mc13783_sw1x_val), - MC13783_DEFINE_SW(SW1B, SWITCHERS1, SWITCHERS1, mc13783_sw1x_val), - MC13783_DEFINE_SW(SW2A, SWITCHERS2, SWITCHERS2, mc13783_sw2x_val), - MC13783_DEFINE_SW(SW2B, SWITCHERS3, SWITCHERS3, mc13783_sw2x_val), - MC13783_DEFINE_SW(SW3, SWITCHERS5, SWITCHERS5, mc13783_sw3_val), - - MC13783_FIXED_DEFINE(REG, VAUDIO, REGULATORMODE0, mc13783_vaudio_val), - MC13783_FIXED_DEFINE(REG, VIOHI, REGULATORMODE0, mc13783_viohi_val), - MC13783_DEFINE_REGU(VIOLO, REGULATORMODE0, REGULATORSETTING0, + MC13783_DEFINE_SW(SW1A, sw1a, SWITCHERS0, SWITCHERS0, mc13783_sw1x_val), + MC13783_DEFINE_SW(SW1B, sw1b, SWITCHERS1, SWITCHERS1, mc13783_sw1x_val), + MC13783_DEFINE_SW(SW2A, sw2a, SWITCHERS2, SWITCHERS2, mc13783_sw2x_val), + MC13783_DEFINE_SW(SW2B, sw2b, SWITCHERS3, SWITCHERS3, mc13783_sw2x_val), + MC13783_DEFINE_SW(SW3, sw3, SWITCHERS5, SWITCHERS5, mc13783_sw3_val), + + MC13783_FIXED_DEFINE(REG, VAUDIO, vaudio, REGULATORMODE0, mc13783_vaudio_val), + MC13783_FIXED_DEFINE(REG, VIOHI, viohi, REGULATORMODE0, mc13783_viohi_val), + MC13783_DEFINE_REGU(VIOLO, violo, REGULATORMODE0, REGULATORSETTING0, mc13783_violo_val), - MC13783_DEFINE_REGU(VDIG, REGULATORMODE0, REGULATORSETTING0, + MC13783_DEFINE_REGU(VDIG, vdig, REGULATORMODE0, REGULATORSETTING0, mc13783_vdig_val), - MC13783_DEFINE_REGU(VGEN, REGULATORMODE0, REGULATORSETTING0, + MC13783_DEFINE_REGU(VGEN, vgen, REGULATORMODE0, REGULATORSETTING0, mc13783_vgen_val), - MC13783_DEFINE_REGU(VRFDIG, REGULATORMODE0, REGULATORSETTING0, + MC13783_DEFINE_REGU(VRFDIG, vrfdig, REGULATORMODE0, REGULATORSETTING0, mc13783_vrfdig_val), - MC13783_DEFINE_REGU(VRFREF, REGULATORMODE0, REGULATORSETTING0, + MC13783_DEFINE_REGU(VRFREF, vrfref, REGULATORMODE0, REGULATORSETTING0, mc13783_vrfref_val), - MC13783_DEFINE_REGU(VRFCP, REGULATORMODE0, REGULATORSETTING0, + MC13783_DEFINE_REGU(VRFCP, vrfcp, REGULATORMODE0, REGULATORSETTING0, mc13783_vrfcp_val), - MC13783_DEFINE_REGU(VSIM, REGULATORMODE1, REGULATORSETTING0, + MC13783_DEFINE_REGU(VSIM, vsim, REGULATORMODE1, REGULATORSETTING0, mc13783_vsim_val), - MC13783_DEFINE_REGU(VESIM, REGULATORMODE1, REGULATORSETTING0, + MC13783_DEFINE_REGU(VESIM, vesim, REGULATORMODE1, REGULATORSETTING0, mc13783_vesim_val), - MC13783_DEFINE_REGU(VCAM, REGULATORMODE1, REGULATORSETTING0, + MC13783_DEFINE_REGU(VCAM, vcam, REGULATORMODE1, REGULATORSETTING0, mc13783_vcam_val), - MC13783_FIXED_DEFINE(REG, VRFBG, REGULATORMODE1, mc13783_vrfbg_val), - MC13783_DEFINE_REGU(VVIB, REGULATORMODE1, REGULATORSETTING1, + MC13783_FIXED_DEFINE(REG, VRFBG, vrfbg, REGULATORMODE1, mc13783_vrfbg_val), + MC13783_DEFINE_REGU(VVIB, vvib, REGULATORMODE1, REGULATORSETTING1, mc13783_vvib_val), - MC13783_DEFINE_REGU(VRF1, REGULATORMODE1, REGULATORSETTING1, + MC13783_DEFINE_REGU(VRF1, vrf1, REGULATORMODE1, REGULATORSETTING1, mc13783_vrf_val), - MC13783_DEFINE_REGU(VRF2, REGULATORMODE1, REGULATORSETTING1, + MC13783_DEFINE_REGU(VRF2, vrf2, REGULATORMODE1, REGULATORSETTING1, mc13783_vrf_val), - MC13783_DEFINE_REGU(VMMC1, REGULATORMODE1, REGULATORSETTING1, + MC13783_DEFINE_REGU(VMMC1, vmmc1, REGULATORMODE1, REGULATORSETTING1, mc13783_vmmc_val), - MC13783_DEFINE_REGU(VMMC2, REGULATORMODE1, REGULATORSETTING1, + MC13783_DEFINE_REGU(VMMC2, vmmc2, REGULATORMODE1, REGULATORSETTING1, mc13783_vmmc_val), - MC13783_GPO_DEFINE(REG, GPO1, POWERMISC, mc13783_gpo_val), - MC13783_GPO_DEFINE(REG, GPO2, POWERMISC, mc13783_gpo_val), - MC13783_GPO_DEFINE(REG, GPO3, POWERMISC, mc13783_gpo_val), - MC13783_GPO_DEFINE(REG, GPO4, POWERMISC, mc13783_gpo_val), - MC13783_GPO_DEFINE(REG, PWGT1SPI, POWERMISC, mc13783_pwgtdrv_val), - MC13783_GPO_DEFINE(REG, PWGT2SPI, POWERMISC, mc13783_pwgtdrv_val), + MC13783_GPO_DEFINE(REG, GPO1, gpo1, POWERMISC, mc13783_gpo_val), + MC13783_GPO_DEFINE(REG, GPO2, gpo1, POWERMISC, mc13783_gpo_val), + MC13783_GPO_DEFINE(REG, GPO3, gpo1, POWERMISC, mc13783_gpo_val), + MC13783_GPO_DEFINE(REG, GPO4, gpo1, POWERMISC, mc13783_gpo_val), + MC13783_GPO_DEFINE(REG, PWGT1SPI, pwgt1spi, POWERMISC, mc13783_pwgtdrv_val), + MC13783_GPO_DEFINE(REG, PWGT2SPI, pwgt2spi, POWERMISC, mc13783_pwgtdrv_val), }; static int mc13783_powermisc_rmw(struct mc13xxx_regulator_priv *priv, u32 mask, @@ -380,7 +380,7 @@ static int mc13783_gpo_regulator_is_enabled(struct regulator_dev *rdev) return (val & mc13xxx_regulators[id].enable_bit) != 0; } -static struct regulator_ops mc13783_gpo_regulator_ops = { +static const struct regulator_ops mc13783_gpo_regulator_ops = { .enable = mc13783_gpo_regulator_enable, .disable = mc13783_gpo_regulator_disable, .is_enabled = mc13783_gpo_regulator_is_enabled, diff --git a/drivers/regulator/mc13892-regulator.c b/drivers/regulator/mc13892-regulator.c index f3fba1cc1379..a731e826a037 100644 --- a/drivers/regulator/mc13892-regulator.c +++ b/drivers/regulator/mc13892-regulator.c @@ -242,61 +242,61 @@ static const unsigned int mc13892_pwgtdrv[] = { 5000000, }; -static struct regulator_ops mc13892_gpo_regulator_ops; -static struct regulator_ops mc13892_sw_regulator_ops; +static const struct regulator_ops mc13892_gpo_regulator_ops; +static const struct regulator_ops mc13892_sw_regulator_ops; -#define MC13892_FIXED_DEFINE(name, reg, voltages) \ - MC13xxx_FIXED_DEFINE(MC13892_, name, reg, voltages, \ +#define MC13892_FIXED_DEFINE(name, node, reg, voltages) \ + MC13xxx_FIXED_DEFINE(MC13892_, name, node, reg, voltages, \ mc13xxx_fixed_regulator_ops) -#define MC13892_GPO_DEFINE(name, reg, voltages) \ - MC13xxx_GPO_DEFINE(MC13892_, name, reg, voltages, \ +#define MC13892_GPO_DEFINE(name, node, reg, voltages) \ + MC13xxx_GPO_DEFINE(MC13892_, name, node, reg, voltages, \ mc13892_gpo_regulator_ops) -#define MC13892_SW_DEFINE(name, reg, vsel_reg, voltages) \ - MC13xxx_DEFINE(MC13892_, name, reg, vsel_reg, voltages, \ +#define MC13892_SW_DEFINE(name, node, reg, vsel_reg, voltages) \ + MC13xxx_DEFINE(MC13892_, name, node, reg, vsel_reg, voltages, \ mc13892_sw_regulator_ops) -#define MC13892_DEFINE_REGU(name, reg, vsel_reg, voltages) \ - MC13xxx_DEFINE(MC13892_, name, reg, vsel_reg, voltages, \ +#define MC13892_DEFINE_REGU(name, node, reg, vsel_reg, voltages) \ + MC13xxx_DEFINE(MC13892_, name, node, reg, vsel_reg, voltages, \ mc13xxx_regulator_ops) static struct mc13xxx_regulator mc13892_regulators[] = { - MC13892_DEFINE_REGU(VCOINCELL, POWERCTL0, POWERCTL0, mc13892_vcoincell), - MC13892_SW_DEFINE(SW1, SWITCHERS0, SWITCHERS0, mc13892_sw1), - MC13892_SW_DEFINE(SW2, SWITCHERS1, SWITCHERS1, mc13892_sw), - MC13892_SW_DEFINE(SW3, SWITCHERS2, SWITCHERS2, mc13892_sw), - MC13892_SW_DEFINE(SW4, SWITCHERS3, SWITCHERS3, mc13892_sw), - MC13892_FIXED_DEFINE(SWBST, SWITCHERS5, mc13892_swbst), - MC13892_FIXED_DEFINE(VIOHI, REGULATORMODE0, mc13892_viohi), - MC13892_DEFINE_REGU(VPLL, REGULATORMODE0, REGULATORSETTING0, + MC13892_DEFINE_REGU(VCOINCELL, vcoincell, POWERCTL0, POWERCTL0, mc13892_vcoincell), + MC13892_SW_DEFINE(SW1, sw1, SWITCHERS0, SWITCHERS0, mc13892_sw1), + MC13892_SW_DEFINE(SW2, sw2, SWITCHERS1, SWITCHERS1, mc13892_sw), + MC13892_SW_DEFINE(SW3, sw3, SWITCHERS2, SWITCHERS2, mc13892_sw), + MC13892_SW_DEFINE(SW4, sw4, SWITCHERS3, SWITCHERS3, mc13892_sw), + MC13892_FIXED_DEFINE(SWBST, swbst, SWITCHERS5, mc13892_swbst), + MC13892_FIXED_DEFINE(VIOHI, viohi, REGULATORMODE0, mc13892_viohi), + MC13892_DEFINE_REGU(VPLL, vpll, REGULATORMODE0, REGULATORSETTING0, mc13892_vpll), - MC13892_DEFINE_REGU(VDIG, REGULATORMODE0, REGULATORSETTING0, + MC13892_DEFINE_REGU(VDIG, vdig, REGULATORMODE0, REGULATORSETTING0, mc13892_vdig), - MC13892_DEFINE_REGU(VSD, REGULATORMODE1, REGULATORSETTING1, + MC13892_DEFINE_REGU(VSD, vsd, REGULATORMODE1, REGULATORSETTING1, mc13892_vsd), - MC13892_DEFINE_REGU(VUSB2, REGULATORMODE0, REGULATORSETTING0, + MC13892_DEFINE_REGU(VUSB2, vusb2, REGULATORMODE0, REGULATORSETTING0, mc13892_vusb2), - MC13892_DEFINE_REGU(VVIDEO, REGULATORMODE1, REGULATORSETTING1, + MC13892_DEFINE_REGU(VVIDEO, vvideo, REGULATORMODE1, REGULATORSETTING1, mc13892_vvideo), - MC13892_DEFINE_REGU(VAUDIO, REGULATORMODE1, REGULATORSETTING1, + MC13892_DEFINE_REGU(VAUDIO, vaudio, REGULATORMODE1, REGULATORSETTING1, mc13892_vaudio), - MC13892_DEFINE_REGU(VCAM, REGULATORMODE1, REGULATORSETTING0, + MC13892_DEFINE_REGU(VCAM, vcam, REGULATORMODE1, REGULATORSETTING0, mc13892_vcam), - MC13892_DEFINE_REGU(VGEN1, REGULATORMODE0, REGULATORSETTING0, + MC13892_DEFINE_REGU(VGEN1, vgen1, REGULATORMODE0, REGULATORSETTING0, mc13892_vgen1), - MC13892_DEFINE_REGU(VGEN2, REGULATORMODE0, REGULATORSETTING0, + MC13892_DEFINE_REGU(VGEN2, vgen2, REGULATORMODE0, REGULATORSETTING0, mc13892_vgen2), - MC13892_DEFINE_REGU(VGEN3, REGULATORMODE1, REGULATORSETTING0, + MC13892_DEFINE_REGU(VGEN3, vgen3, REGULATORMODE1, REGULATORSETTING0, mc13892_vgen3), - MC13892_FIXED_DEFINE(VUSB, USB1, mc13892_vusb), - MC13892_GPO_DEFINE(GPO1, POWERMISC, mc13892_gpo), - MC13892_GPO_DEFINE(GPO2, POWERMISC, mc13892_gpo), - MC13892_GPO_DEFINE(GPO3, POWERMISC, mc13892_gpo), - MC13892_GPO_DEFINE(GPO4, POWERMISC, mc13892_gpo), - MC13892_GPO_DEFINE(PWGT1SPI, POWERMISC, mc13892_pwgtdrv), - MC13892_GPO_DEFINE(PWGT2SPI, POWERMISC, mc13892_pwgtdrv), + MC13892_FIXED_DEFINE(VUSB, vusb, USB1, mc13892_vusb), + MC13892_GPO_DEFINE(GPO1, gpo1, POWERMISC, mc13892_gpo), + MC13892_GPO_DEFINE(GPO2, gpo2, POWERMISC, mc13892_gpo), + MC13892_GPO_DEFINE(GPO3, gpo3, POWERMISC, mc13892_gpo), + MC13892_GPO_DEFINE(GPO4, gpo4, POWERMISC, mc13892_gpo), + MC13892_GPO_DEFINE(PWGT1SPI, pwgt1spi, POWERMISC, mc13892_pwgtdrv), + MC13892_GPO_DEFINE(PWGT2SPI, pwgt2spi, POWERMISC, mc13892_pwgtdrv), }; static int mc13892_powermisc_rmw(struct mc13xxx_regulator_priv *priv, u32 mask, @@ -387,7 +387,7 @@ static int mc13892_gpo_regulator_is_enabled(struct regulator_dev *rdev) } -static struct regulator_ops mc13892_gpo_regulator_ops = { +static const struct regulator_ops mc13892_gpo_regulator_ops = { .enable = mc13892_gpo_regulator_enable, .disable = mc13892_gpo_regulator_disable, .is_enabled = mc13892_gpo_regulator_is_enabled, @@ -479,7 +479,7 @@ static int mc13892_sw_regulator_set_voltage_sel(struct regulator_dev *rdev, return ret; } -static struct regulator_ops mc13892_sw_regulator_ops = { +static const struct regulator_ops mc13892_sw_regulator_ops = { .list_voltage = regulator_list_voltage_table, .map_voltage = regulator_map_voltage_ascend, .set_voltage_sel = mc13892_sw_regulator_set_voltage_sel, diff --git a/drivers/regulator/mc13xxx-regulator-core.c b/drivers/regulator/mc13xxx-regulator-core.c index 2243138d8a58..8ff19150ca92 100644 --- a/drivers/regulator/mc13xxx-regulator-core.c +++ b/drivers/regulator/mc13xxx-regulator-core.c @@ -99,7 +99,7 @@ static int mc13xxx_regulator_get_voltage(struct regulator_dev *rdev) return rdev->desc->volt_table[val]; } -struct regulator_ops mc13xxx_regulator_ops = { +const struct regulator_ops mc13xxx_regulator_ops = { .enable = mc13xxx_regulator_enable, .disable = mc13xxx_regulator_disable, .is_enabled = mc13xxx_regulator_is_enabled, @@ -127,7 +127,7 @@ int mc13xxx_fixed_regulator_set_voltage(struct regulator_dev *rdev, int min_uV, } EXPORT_SYMBOL_GPL(mc13xxx_fixed_regulator_set_voltage); -struct regulator_ops mc13xxx_fixed_regulator_ops = { +const struct regulator_ops mc13xxx_fixed_regulator_ops = { .enable = mc13xxx_regulator_enable, .disable = mc13xxx_regulator_disable, .is_enabled = mc13xxx_regulator_is_enabled, diff --git a/drivers/regulator/mc13xxx.h b/drivers/regulator/mc13xxx.h index 2ab9bfd93b4e..ba7eff1070bd 100644 --- a/drivers/regulator/mc13xxx.h +++ b/drivers/regulator/mc13xxx.h @@ -53,13 +53,13 @@ static inline struct mc13xxx_regulator_init_data *mc13xxx_parse_regulators_dt( } #endif -extern struct regulator_ops mc13xxx_regulator_ops; -extern struct regulator_ops mc13xxx_fixed_regulator_ops; +extern const struct regulator_ops mc13xxx_regulator_ops; +extern const struct regulator_ops mc13xxx_fixed_regulator_ops; -#define MC13xxx_DEFINE(prefix, _name, _reg, _vsel_reg, _voltages, _ops) \ +#define MC13xxx_DEFINE(prefix, _name, _node, _reg, _vsel_reg, _voltages, _ops) \ [prefix ## _name] = { \ .desc = { \ - .name = #_name, \ + .name = #_node, \ .n_voltages = ARRAY_SIZE(_voltages), \ .volt_table = _voltages, \ .ops = &_ops, \ @@ -74,10 +74,10 @@ extern struct regulator_ops mc13xxx_fixed_regulator_ops; .vsel_mask = prefix ## _vsel_reg ## _ ## _name ## VSEL_M,\ } -#define MC13xxx_FIXED_DEFINE(prefix, _name, _reg, _voltages, _ops) \ +#define MC13xxx_FIXED_DEFINE(prefix, _name, _node, _reg, _voltages, _ops) \ [prefix ## _name] = { \ .desc = { \ - .name = #_name, \ + .name = #_node, \ .n_voltages = ARRAY_SIZE(_voltages), \ .volt_table = _voltages, \ .ops = &_ops, \ @@ -89,10 +89,10 @@ extern struct regulator_ops mc13xxx_fixed_regulator_ops; .enable_bit = prefix ## _reg ## _ ## _name ## EN, \ } -#define MC13xxx_GPO_DEFINE(prefix, _name, _reg, _voltages, _ops) \ +#define MC13xxx_GPO_DEFINE(prefix, _name, _node, _reg, _voltages, _ops) \ [prefix ## _name] = { \ .desc = { \ - .name = #_name, \ + .name = #_node, \ .n_voltages = ARRAY_SIZE(_voltages), \ .volt_table = _voltages, \ .ops = &_ops, \ @@ -104,9 +104,9 @@ extern struct regulator_ops mc13xxx_fixed_regulator_ops; .enable_bit = prefix ## _reg ## _ ## _name ## EN, \ } -#define MC13xxx_DEFINE_SW(_name, _reg, _vsel_reg, _voltages, ops) \ - MC13xxx_DEFINE(SW, _name, _reg, _vsel_reg, _voltages, ops) -#define MC13xxx_DEFINE_REGU(_name, _reg, _vsel_reg, _voltages, ops) \ - MC13xxx_DEFINE(REGU, _name, _reg, _vsel_reg, _voltages, ops) +#define MC13xxx_DEFINE_SW(_name, _node, _reg, _vsel_reg, _voltages, ops) \ + MC13xxx_DEFINE(SW, _name, _node, _reg, _vsel_reg, _voltages, ops) +#define MC13xxx_DEFINE_REGU(_name, _node, _reg, _vsel_reg, _voltages, ops) \ + MC13xxx_DEFINE(REGU, _name, _node, _reg, _vsel_reg, _voltages, ops) #endif diff --git a/drivers/regulator/mcp16502.c b/drivers/regulator/mcp16502.c index 3479ae009b0b..3a8004abe044 100644 --- a/drivers/regulator/mcp16502.c +++ b/drivers/regulator/mcp16502.c @@ -17,6 +17,7 @@ #include <linux/regmap.h> #include <linux/regulator/driver.h> #include <linux/suspend.h> +#include <linux/gpio/consumer.h> #define VDD_LOW_SEL 0x0D #define VDD_HIGH_SEL 0x3F @@ -546,7 +547,6 @@ static struct i2c_driver mcp16502_drv = { module_i2c_driver(mcp16502_drv); -MODULE_VERSION("1.0"); MODULE_LICENSE("GPL v2"); MODULE_DESCRIPTION("MCP16502 PMIC driver"); MODULE_AUTHOR("Andrei Stefanescu andrei.stefanescu@microchip.com"); diff --git a/drivers/regulator/mt6311-regulator.c b/drivers/regulator/mt6311-regulator.c index 0495716fd35f..01d69f43d2b0 100644 --- a/drivers/regulator/mt6311-regulator.c +++ b/drivers/regulator/mt6311-regulator.c @@ -38,13 +38,9 @@ static const struct regmap_config mt6311_regmap_config = { #define MT6311_MAX_UV 1393750 #define MT6311_STEP_UV 6250 -static const struct regulator_linear_range buck_volt_range[] = { - REGULATOR_LINEAR_RANGE(MT6311_MIN_UV, 0, 0x7f, MT6311_STEP_UV), -}; - static const struct regulator_ops mt6311_buck_ops = { - .list_voltage = regulator_list_voltage_linear_range, - .map_voltage = regulator_map_voltage_linear_range, + .list_voltage = regulator_list_voltage_linear, + .map_voltage = regulator_map_voltage_linear, .set_voltage_sel = regulator_set_voltage_sel_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, .set_voltage_time_sel = regulator_set_voltage_time_sel, @@ -71,8 +67,6 @@ static const struct regulator_ops mt6311_ldo_ops = { .min_uV = MT6311_MIN_UV,\ .uV_step = MT6311_STEP_UV,\ .owner = THIS_MODULE,\ - .linear_ranges = buck_volt_range, \ - .n_linear_ranges = ARRAY_SIZE(buck_volt_range), \ .enable_reg = MT6311_VDVFS11_CON9,\ .enable_mask = MT6311_PMIC_VDVFS11_EN_MASK,\ .vsel_reg = MT6311_VDVFS11_CON12,\ diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c index ffa5fc3724e4..7b6bf3536271 100644 --- a/drivers/regulator/of_regulator.c +++ b/drivers/regulator/of_regulator.c @@ -255,7 +255,7 @@ static void of_get_regulation_constraints(struct device_node *np, * @desc: regulator description * * Populates regulator_init_data structure by extracting data from device - * tree node, returns a pointer to the populated struture or NULL if memory + * tree node, returns a pointer to the populated structure or NULL if memory * alloc fails. */ struct regulator_init_data *of_get_regulator_init_data(struct device *dev, @@ -547,7 +547,7 @@ bool of_check_coupling_data(struct regulator_dev *rdev) NULL); if (c_n_phandles != n_phandles) { - dev_err(&rdev->dev, "number of couped reg phandles mismatch\n"); + dev_err(&rdev->dev, "number of coupled reg phandles mismatch\n"); ret = false; goto clean; } diff --git a/drivers/regulator/palmas-regulator.c b/drivers/regulator/palmas-regulator.c index c2cc392a27d4..7fb9e8dd834e 100644 --- a/drivers/regulator/palmas-regulator.c +++ b/drivers/regulator/palmas-regulator.c @@ -382,7 +382,7 @@ static struct palmas_sleep_requestor_info tps65917_sleep_req_info[] = { EXTERNAL_REQUESTOR_TPS65917(LDO5, 2, 4), }; -static unsigned int palmas_smps_ramp_delay[4] = {0, 10000, 5000, 2500}; +static const unsigned int palmas_smps_ramp_delay[4] = {0, 10000, 5000, 2500}; #define SMPS_CTRL_MODE_OFF 0x00 #define SMPS_CTRL_MODE_ON 0x01 diff --git a/drivers/regulator/pv88060-regulator.c b/drivers/regulator/pv88060-regulator.c index a9446056435f..1600f9821891 100644 --- a/drivers/regulator/pv88060-regulator.c +++ b/drivers/regulator/pv88060-regulator.c @@ -53,10 +53,6 @@ enum { struct pv88060_regulator { struct regulator_desc desc; - /* Current limiting */ - unsigned n_current_limits; - const int *current_limits; - unsigned int limit_mask; unsigned int conf; /* buck configuration register */ }; @@ -75,7 +71,7 @@ static const struct regmap_config pv88060_regmap_config = { * Entry indexes corresponds to register values. */ -static const int pv88060_buck1_limits[] = { +static const unsigned int pv88060_buck1_limits[] = { 1496000, 2393000, 3291000, 4189000 }; @@ -128,40 +124,6 @@ static int pv88060_buck_set_mode(struct regulator_dev *rdev, PV88060_BUCK_MODE_MASK, val); } -static int pv88060_set_current_limit(struct regulator_dev *rdev, int min, - int max) -{ - struct pv88060_regulator *info = rdev_get_drvdata(rdev); - int i; - - /* search for closest to maximum */ - for (i = info->n_current_limits; i >= 0; i--) { - if (min <= info->current_limits[i] - && max >= info->current_limits[i]) { - return regmap_update_bits(rdev->regmap, - info->conf, - info->limit_mask, - i << PV88060_BUCK_ILIM_SHIFT); - } - } - - return -EINVAL; -} - -static int pv88060_get_current_limit(struct regulator_dev *rdev) -{ - struct pv88060_regulator *info = rdev_get_drvdata(rdev); - unsigned int data; - int ret; - - ret = regmap_read(rdev->regmap, info->conf, &data); - if (ret < 0) - return ret; - - data = (data & info->limit_mask) >> PV88060_BUCK_ILIM_SHIFT; - return info->current_limits[data]; -} - static const struct regulator_ops pv88060_buck_ops = { .get_mode = pv88060_buck_get_mode, .set_mode = pv88060_buck_set_mode, @@ -171,8 +133,8 @@ static const struct regulator_ops pv88060_buck_ops = { .set_voltage_sel = regulator_set_voltage_sel_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, .list_voltage = regulator_list_voltage_linear, - .set_current_limit = pv88060_set_current_limit, - .get_current_limit = pv88060_get_current_limit, + .set_current_limit = regulator_set_current_limit_regmap, + .get_current_limit = regulator_get_current_limit_regmap, }; static const struct regulator_ops pv88060_ldo_ops = { @@ -184,6 +146,12 @@ static const struct regulator_ops pv88060_ldo_ops = { .list_voltage = regulator_list_voltage_linear, }; +static const struct regulator_ops pv88060_sw_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, +}; + #define PV88060_BUCK(chip, regl_name, min, step, max, limits_array) \ {\ .desc = {\ @@ -201,10 +169,11 @@ static const struct regulator_ops pv88060_ldo_ops = { .enable_mask = PV88060_BUCK_EN, \ .vsel_reg = PV88060_REG_##regl_name##_CONF0,\ .vsel_mask = PV88060_VBUCK_MASK,\ + .curr_table = limits_array,\ + .n_current_limits = ARRAY_SIZE(limits_array),\ + .csel_reg = PV88060_REG_##regl_name##_CONF1,\ + .csel_mask = PV88060_BUCK_ILIM_MASK,\ },\ - .current_limits = limits_array,\ - .n_current_limits = ARRAY_SIZE(limits_array),\ - .limit_mask = PV88060_BUCK_ILIM_MASK, \ .conf = PV88060_REG_##regl_name##_CONF1,\ } @@ -237,9 +206,8 @@ static const struct regulator_ops pv88060_ldo_ops = { .regulators_node = of_match_ptr("regulators"),\ .type = REGULATOR_VOLTAGE,\ .owner = THIS_MODULE,\ - .ops = &pv88060_ldo_ops,\ - .min_uV = max,\ - .uV_step = 0,\ + .ops = &pv88060_sw_ops,\ + .fixed_uV = max,\ .n_voltages = 1,\ .enable_reg = PV88060_REG_##regl_name##_CONF,\ .enable_mask = PV88060_SW_EN,\ diff --git a/drivers/regulator/pv88080-regulator.c b/drivers/regulator/pv88080-regulator.c index 9a08cb2de501..bdddacdbeb99 100644 --- a/drivers/regulator/pv88080-regulator.c +++ b/drivers/regulator/pv88080-regulator.c @@ -45,12 +45,7 @@ enum pv88080_types { struct pv88080_regulator { struct regulator_desc desc; - /* Current limiting */ - unsigned int n_current_limits; - const int *current_limits; - unsigned int limit_mask; unsigned int mode_reg; - unsigned int limit_reg; unsigned int conf2; unsigned int conf5; }; @@ -102,11 +97,11 @@ static const struct regmap_config pv88080_regmap_config = { * Entry indexes corresponds to register values. */ -static const int pv88080_buck1_limits[] = { +static const unsigned int pv88080_buck1_limits[] = { 3230000, 5130000, 6960000, 8790000 }; -static const int pv88080_buck23_limits[] = { +static const unsigned int pv88080_buck23_limits[] = { 1496000, 2393000, 3291000, 4189000 }; @@ -272,40 +267,6 @@ static int pv88080_buck_set_mode(struct regulator_dev *rdev, PV88080_BUCK1_MODE_MASK, val); } -static int pv88080_set_current_limit(struct regulator_dev *rdev, int min, - int max) -{ - struct pv88080_regulator *info = rdev_get_drvdata(rdev); - int i; - - /* search for closest to maximum */ - for (i = info->n_current_limits; i >= 0; i--) { - if (min <= info->current_limits[i] - && max >= info->current_limits[i]) { - return regmap_update_bits(rdev->regmap, - info->limit_reg, - info->limit_mask, - i << PV88080_BUCK1_ILIM_SHIFT); - } - } - - return -EINVAL; -} - -static int pv88080_get_current_limit(struct regulator_dev *rdev) -{ - struct pv88080_regulator *info = rdev_get_drvdata(rdev); - unsigned int data; - int ret; - - ret = regmap_read(rdev->regmap, info->limit_reg, &data); - if (ret < 0) - return ret; - - data = (data & info->limit_mask) >> PV88080_BUCK1_ILIM_SHIFT; - return info->current_limits[data]; -} - static const struct regulator_ops pv88080_buck_ops = { .get_mode = pv88080_buck_get_mode, .set_mode = pv88080_buck_set_mode, @@ -315,8 +276,8 @@ static const struct regulator_ops pv88080_buck_ops = { .set_voltage_sel = regulator_set_voltage_sel_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, .list_voltage = regulator_list_voltage_linear, - .set_current_limit = pv88080_set_current_limit, - .get_current_limit = pv88080_get_current_limit, + .set_current_limit = regulator_set_current_limit_regmap, + .get_current_limit = regulator_get_current_limit_regmap, }; static const struct regulator_ops pv88080_hvbuck_ops = { @@ -341,9 +302,9 @@ static const struct regulator_ops pv88080_hvbuck_ops = { .min_uV = min, \ .uV_step = step, \ .n_voltages = ((max) - (min))/(step) + 1, \ + .curr_table = limits_array, \ + .n_current_limits = ARRAY_SIZE(limits_array), \ },\ - .current_limits = limits_array, \ - .n_current_limits = ARRAY_SIZE(limits_array), \ } #define PV88080_HVBUCK(chip, regl_name, min, step, max) \ @@ -521,9 +482,9 @@ static int pv88080_i2c_probe(struct i2c_client *i2c, if (init_data) config.init_data = &init_data[i]; - pv88080_regulator_info[i].limit_reg + pv88080_regulator_info[i].desc.csel_reg = regmap_config->buck_regmap[i].buck_limit_reg; - pv88080_regulator_info[i].limit_mask + pv88080_regulator_info[i].desc.csel_mask = regmap_config->buck_regmap[i].buck_limit_mask; pv88080_regulator_info[i].mode_reg = regmap_config->buck_regmap[i].buck_mode_reg; diff --git a/drivers/regulator/pv88090-regulator.c b/drivers/regulator/pv88090-regulator.c index 7a0c15957bd0..6e97cc6df2ee 100644 --- a/drivers/regulator/pv88090-regulator.c +++ b/drivers/regulator/pv88090-regulator.c @@ -42,10 +42,6 @@ enum { struct pv88090_regulator { struct regulator_desc desc; - /* Current limiting */ - unsigned int n_current_limits; - const int *current_limits; - unsigned int limit_mask; unsigned int conf; unsigned int conf2; }; @@ -71,14 +67,14 @@ static const struct regmap_config pv88090_regmap_config = { * Entry indexes corresponds to register values. */ -static const int pv88090_buck1_limits[] = { +static const unsigned int pv88090_buck1_limits[] = { 220000, 440000, 660000, 880000, 1100000, 1320000, 1540000, 1760000, 1980000, 2200000, 2420000, 2640000, 2860000, 3080000, 3300000, 3520000, 3740000, 3960000, 4180000, 4400000, 4620000, 4840000, 5060000, 5280000, 5500000, 5720000, 5940000, 6160000, 6380000, 6600000, 6820000, 7040000 }; -static const int pv88090_buck23_limits[] = { +static const unsigned int pv88090_buck23_limits[] = { 1496000, 2393000, 3291000, 4189000 }; @@ -150,40 +146,6 @@ static int pv88090_buck_set_mode(struct regulator_dev *rdev, PV88090_BUCK1_MODE_MASK, val); } -static int pv88090_set_current_limit(struct regulator_dev *rdev, int min, - int max) -{ - struct pv88090_regulator *info = rdev_get_drvdata(rdev); - int i; - - /* search for closest to maximum */ - for (i = info->n_current_limits; i >= 0; i--) { - if (min <= info->current_limits[i] - && max >= info->current_limits[i]) { - return regmap_update_bits(rdev->regmap, - info->conf, - info->limit_mask, - i << PV88090_BUCK1_ILIM_SHIFT); - } - } - - return -EINVAL; -} - -static int pv88090_get_current_limit(struct regulator_dev *rdev) -{ - struct pv88090_regulator *info = rdev_get_drvdata(rdev); - unsigned int data; - int ret; - - ret = regmap_read(rdev->regmap, info->conf, &data); - if (ret < 0) - return ret; - - data = (data & info->limit_mask) >> PV88090_BUCK1_ILIM_SHIFT; - return info->current_limits[data]; -} - static const struct regulator_ops pv88090_buck_ops = { .get_mode = pv88090_buck_get_mode, .set_mode = pv88090_buck_set_mode, @@ -193,8 +155,8 @@ static const struct regulator_ops pv88090_buck_ops = { .set_voltage_sel = regulator_set_voltage_sel_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, .list_voltage = regulator_list_voltage_linear, - .set_current_limit = pv88090_set_current_limit, - .get_current_limit = pv88090_get_current_limit, + .set_current_limit = regulator_set_current_limit_regmap, + .get_current_limit = regulator_get_current_limit_regmap, }; static const struct regulator_ops pv88090_ldo_ops = { @@ -223,10 +185,11 @@ static const struct regulator_ops pv88090_ldo_ops = { .enable_mask = PV88090_##regl_name##_EN, \ .vsel_reg = PV88090_REG_##regl_name##_CONF0, \ .vsel_mask = PV88090_V##regl_name##_MASK, \ + .curr_table = limits_array, \ + .n_current_limits = ARRAY_SIZE(limits_array), \ + .csel_reg = PV88090_REG_##regl_name##_CONF1, \ + .csel_mask = PV88090_##regl_name##_ILIM_MASK, \ },\ - .current_limits = limits_array, \ - .n_current_limits = ARRAY_SIZE(limits_array), \ - .limit_mask = PV88090_##regl_name##_ILIM_MASK, \ .conf = PV88090_REG_##regl_name##_CONF1, \ .conf2 = PV88090_REG_##regl_name##_CONF2, \ } diff --git a/drivers/regulator/pwm-regulator.c b/drivers/regulator/pwm-regulator.c index a2fd140eff81..3f53f9134b32 100644 --- a/drivers/regulator/pwm-regulator.c +++ b/drivers/regulator/pwm-regulator.c @@ -40,9 +40,6 @@ struct pwm_regulator_data { /* regulator descriptor */ struct regulator_desc desc; - /* Regulator ops */ - struct regulator_ops ops; - int state; /* Enable GPIO */ @@ -231,7 +228,7 @@ static int pwm_regulator_set_voltage(struct regulator_dev *rdev, return 0; } -static struct regulator_ops pwm_regulator_voltage_table_ops = { +static const struct regulator_ops pwm_regulator_voltage_table_ops = { .set_voltage_sel = pwm_regulator_set_voltage_sel, .get_voltage_sel = pwm_regulator_get_voltage_sel, .list_voltage = pwm_regulator_list_voltage, @@ -241,7 +238,7 @@ static struct regulator_ops pwm_regulator_voltage_table_ops = { .is_enabled = pwm_regulator_is_enabled, }; -static struct regulator_ops pwm_regulator_voltage_continuous_ops = { +static const struct regulator_ops pwm_regulator_voltage_continuous_ops = { .get_voltage = pwm_regulator_get_voltage, .set_voltage = pwm_regulator_set_voltage, .enable = pwm_regulator_enable, @@ -249,7 +246,7 @@ static struct regulator_ops pwm_regulator_voltage_continuous_ops = { .is_enabled = pwm_regulator_is_enabled, }; -static struct regulator_desc pwm_regulator_desc = { +static const struct regulator_desc pwm_regulator_desc = { .name = "pwm-regulator", .type = REGULATOR_VOLTAGE, .owner = THIS_MODULE, @@ -287,9 +284,7 @@ static int pwm_regulator_init_table(struct platform_device *pdev, drvdata->state = -EINVAL; drvdata->duty_cycle_table = duty_cycle_table; - memcpy(&drvdata->ops, &pwm_regulator_voltage_table_ops, - sizeof(drvdata->ops)); - drvdata->desc.ops = &drvdata->ops; + drvdata->desc.ops = &pwm_regulator_voltage_table_ops; drvdata->desc.n_voltages = length / sizeof(*duty_cycle_table); return 0; @@ -301,9 +296,7 @@ static int pwm_regulator_init_continuous(struct platform_device *pdev, u32 dutycycle_range[2] = { 0, 100 }; u32 dutycycle_unit = 100; - memcpy(&drvdata->ops, &pwm_regulator_voltage_continuous_ops, - sizeof(drvdata->ops)); - drvdata->desc.ops = &drvdata->ops; + drvdata->desc.ops = &pwm_regulator_voltage_continuous_ops; drvdata->desc.continuous_voltage_range = true; of_property_read_u32_array(pdev->dev.of_node, diff --git a/drivers/regulator/qcom_smd-regulator.c b/drivers/regulator/qcom_smd-regulator.c index f5bca77d67c1..68bc23df4213 100644 --- a/drivers/regulator/qcom_smd-regulator.c +++ b/drivers/regulator/qcom_smd-regulator.c @@ -31,6 +31,11 @@ struct qcom_rpm_reg { int is_enabled; int uV; + u32 load; + + unsigned int enabled_updated:1; + unsigned int uv_updated:1; + unsigned int load_updated:1; }; struct rpm_regulator_req { @@ -43,30 +48,59 @@ struct rpm_regulator_req { #define RPM_KEY_UV 0x00007675 /* "uv" */ #define RPM_KEY_MA 0x0000616d /* "ma" */ -static int rpm_reg_write_active(struct qcom_rpm_reg *vreg, - struct rpm_regulator_req *req, - size_t size) +static int rpm_reg_write_active(struct qcom_rpm_reg *vreg) { - return qcom_rpm_smd_write(vreg->rpm, - QCOM_SMD_RPM_ACTIVE_STATE, - vreg->type, - vreg->id, - req, size); + struct rpm_regulator_req req[3]; + int reqlen = 0; + int ret; + + if (vreg->enabled_updated) { + req[reqlen].key = cpu_to_le32(RPM_KEY_SWEN); + req[reqlen].nbytes = cpu_to_le32(sizeof(u32)); + req[reqlen].value = cpu_to_le32(vreg->is_enabled); + reqlen++; + } + + if (vreg->uv_updated && vreg->is_enabled) { + req[reqlen].key = cpu_to_le32(RPM_KEY_UV); + req[reqlen].nbytes = cpu_to_le32(sizeof(u32)); + req[reqlen].value = cpu_to_le32(vreg->uV); + reqlen++; + } + + if (vreg->load_updated && vreg->is_enabled) { + req[reqlen].key = cpu_to_le32(RPM_KEY_MA); + req[reqlen].nbytes = cpu_to_le32(sizeof(u32)); + req[reqlen].value = cpu_to_le32(vreg->load / 1000); + reqlen++; + } + + if (!reqlen) + return 0; + + ret = qcom_rpm_smd_write(vreg->rpm, QCOM_SMD_RPM_ACTIVE_STATE, + vreg->type, vreg->id, + req, sizeof(req[0]) * reqlen); + if (!ret) { + vreg->enabled_updated = 0; + vreg->uv_updated = 0; + vreg->load_updated = 0; + } + + return ret; } static int rpm_reg_enable(struct regulator_dev *rdev) { struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); - struct rpm_regulator_req req; int ret; - req.key = cpu_to_le32(RPM_KEY_SWEN); - req.nbytes = cpu_to_le32(sizeof(u32)); - req.value = cpu_to_le32(1); + vreg->is_enabled = 1; + vreg->enabled_updated = 1; - ret = rpm_reg_write_active(vreg, &req, sizeof(req)); - if (!ret) - vreg->is_enabled = 1; + ret = rpm_reg_write_active(vreg); + if (ret) + vreg->is_enabled = 0; return ret; } @@ -81,16 +115,14 @@ static int rpm_reg_is_enabled(struct regulator_dev *rdev) static int rpm_reg_disable(struct regulator_dev *rdev) { struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); - struct rpm_regulator_req req; int ret; - req.key = cpu_to_le32(RPM_KEY_SWEN); - req.nbytes = cpu_to_le32(sizeof(u32)); - req.value = 0; + vreg->is_enabled = 0; + vreg->enabled_updated = 1; - ret = rpm_reg_write_active(vreg, &req, sizeof(req)); - if (!ret) - vreg->is_enabled = 0; + ret = rpm_reg_write_active(vreg); + if (ret) + vreg->is_enabled = 1; return ret; } @@ -108,16 +140,15 @@ static int rpm_reg_set_voltage(struct regulator_dev *rdev, unsigned *selector) { struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); - struct rpm_regulator_req req; - int ret = 0; + int ret; + int old_uV = vreg->uV; - req.key = cpu_to_le32(RPM_KEY_UV); - req.nbytes = cpu_to_le32(sizeof(u32)); - req.value = cpu_to_le32(min_uV); + vreg->uV = min_uV; + vreg->uv_updated = 1; - ret = rpm_reg_write_active(vreg, &req, sizeof(req)); - if (!ret) - vreg->uV = min_uV; + ret = rpm_reg_write_active(vreg); + if (ret) + vreg->uV = old_uV; return ret; } @@ -125,13 +156,16 @@ static int rpm_reg_set_voltage(struct regulator_dev *rdev, static int rpm_reg_set_load(struct regulator_dev *rdev, int load_uA) { struct qcom_rpm_reg *vreg = rdev_get_drvdata(rdev); - struct rpm_regulator_req req; + u32 old_load = vreg->load; + int ret; - req.key = cpu_to_le32(RPM_KEY_MA); - req.nbytes = cpu_to_le32(sizeof(u32)); - req.value = cpu_to_le32(load_uA / 1000); + vreg->load = load_uA; + vreg->load_updated = 1; + ret = rpm_reg_write_active(vreg); + if (ret) + vreg->load = old_load; - return rpm_reg_write_active(vreg, &req, sizeof(req)); + return ret; } static const struct regulator_ops rpm_smps_ldo_ops = { diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c index 213b68743cc8..23713e16c286 100644 --- a/drivers/regulator/rk808-regulator.c +++ b/drivers/regulator/rk808-regulator.c @@ -1,5 +1,5 @@ /* - * Regulator driver for Rockchip RK808/RK818 + * Regulator driver for Rockchip RK805/RK808/RK818 * * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd * @@ -363,28 +363,28 @@ static int rk808_set_suspend_disable(struct regulator_dev *rdev) rdev->desc->enable_mask); } -static struct regulator_ops rk805_reg_ops = { - .list_voltage = regulator_list_voltage_linear, - .map_voltage = regulator_map_voltage_linear, - .get_voltage_sel = regulator_get_voltage_sel_regmap, - .set_voltage_sel = regulator_set_voltage_sel_regmap, - .enable = regulator_enable_regmap, - .disable = regulator_disable_regmap, - .is_enabled = regulator_is_enabled_regmap, - .set_suspend_voltage = rk808_set_suspend_voltage, - .set_suspend_enable = rk805_set_suspend_enable, - .set_suspend_disable = rk805_set_suspend_disable, +static const struct regulator_ops rk805_reg_ops = { + .list_voltage = regulator_list_voltage_linear, + .map_voltage = regulator_map_voltage_linear, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .set_suspend_voltage = rk808_set_suspend_voltage, + .set_suspend_enable = rk805_set_suspend_enable, + .set_suspend_disable = rk805_set_suspend_disable, }; -static struct regulator_ops rk805_switch_ops = { - .enable = regulator_enable_regmap, - .disable = regulator_disable_regmap, - .is_enabled = regulator_is_enabled_regmap, - .set_suspend_enable = rk805_set_suspend_enable, - .set_suspend_disable = rk805_set_suspend_disable, +static const struct regulator_ops rk805_switch_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .set_suspend_enable = rk805_set_suspend_enable, + .set_suspend_disable = rk805_set_suspend_disable, }; -static struct regulator_ops rk808_buck1_2_ops = { +static const struct regulator_ops rk808_buck1_2_ops = { .list_voltage = regulator_list_voltage_linear, .map_voltage = regulator_map_voltage_linear, .get_voltage_sel = rk808_buck1_2_get_voltage_sel_regmap, @@ -399,7 +399,7 @@ static struct regulator_ops rk808_buck1_2_ops = { .set_suspend_disable = rk808_set_suspend_disable, }; -static struct regulator_ops rk808_reg_ops = { +static const struct regulator_ops rk808_reg_ops = { .list_voltage = regulator_list_voltage_linear, .map_voltage = regulator_map_voltage_linear, .get_voltage_sel = regulator_get_voltage_sel_regmap, @@ -412,7 +412,7 @@ static struct regulator_ops rk808_reg_ops = { .set_suspend_disable = rk808_set_suspend_disable, }; -static struct regulator_ops rk808_reg_ops_ranges = { +static const struct regulator_ops rk808_reg_ops_ranges = { .list_voltage = regulator_list_voltage_linear_range, .map_voltage = regulator_map_voltage_linear_range, .get_voltage_sel = regulator_get_voltage_sel_regmap, @@ -425,7 +425,7 @@ static struct regulator_ops rk808_reg_ops_ranges = { .set_suspend_disable = rk808_set_suspend_disable, }; -static struct regulator_ops rk808_switch_ops = { +static const struct regulator_ops rk808_switch_ops = { .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .is_enabled = regulator_is_enabled_regmap, @@ -433,6 +433,12 @@ static struct regulator_ops rk808_switch_ops = { .set_suspend_disable = rk808_set_suspend_disable, }; +static const struct regulator_linear_range rk805_buck_1_2_voltage_ranges[] = { + REGULATOR_LINEAR_RANGE(712500, 0, 59, 12500), + REGULATOR_LINEAR_RANGE(1800000, 60, 62, 200000), + REGULATOR_LINEAR_RANGE(2300000, 63, 63, 0), +}; + static const struct regulator_desc rk805_reg[] = { { .name = "DCDC_REG1", @@ -440,11 +446,11 @@ static const struct regulator_desc rk805_reg[] = { .of_match = of_match_ptr("DCDC_REG1"), .regulators_node = of_match_ptr("regulators"), .id = RK805_ID_DCDC1, - .ops = &rk805_reg_ops, + .ops = &rk808_reg_ops_ranges, .type = REGULATOR_VOLTAGE, - .min_uV = 712500, - .uV_step = 12500, .n_voltages = 64, + .linear_ranges = rk805_buck_1_2_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges), .vsel_reg = RK805_BUCK1_ON_VSEL_REG, .vsel_mask = RK818_BUCK_VSEL_MASK, .enable_reg = RK805_DCDC_EN_REG, @@ -456,11 +462,11 @@ static const struct regulator_desc rk805_reg[] = { .of_match = of_match_ptr("DCDC_REG2"), .regulators_node = of_match_ptr("regulators"), .id = RK805_ID_DCDC2, - .ops = &rk805_reg_ops, + .ops = &rk808_reg_ops_ranges, .type = REGULATOR_VOLTAGE, - .min_uV = 712500, - .uV_step = 12500, .n_voltages = 64, + .linear_ranges = rk805_buck_1_2_voltage_ranges, + .n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges), .vsel_reg = RK805_BUCK2_ON_VSEL_REG, .vsel_mask = RK818_BUCK_VSEL_MASK, .enable_reg = RK805_DCDC_EN_REG, @@ -796,7 +802,7 @@ static struct platform_driver rk808_regulator_driver = { module_platform_driver(rk808_regulator_driver); -MODULE_DESCRIPTION("regulator driver for the RK808/RK818 series PMICs"); +MODULE_DESCRIPTION("regulator driver for the RK805/RK808/RK818 series PMICs"); MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>"); MODULE_AUTHOR("Zhang Qing <zhangqing@rock-chips.com>"); MODULE_AUTHOR("Wadim Egorov <w.egorov@phytec.de>"); diff --git a/drivers/regulator/rt5033-regulator.c b/drivers/regulator/rt5033-regulator.c index 96d2c18e051a..639cbadc044a 100644 --- a/drivers/regulator/rt5033-regulator.c +++ b/drivers/regulator/rt5033-regulator.c @@ -16,14 +16,14 @@ #include <linux/mfd/rt5033-private.h> #include <linux/regulator/of_regulator.h> -static struct regulator_ops rt5033_safe_ldo_ops = { +static const struct regulator_ops rt5033_safe_ldo_ops = { .is_enabled = regulator_is_enabled_regmap, .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .list_voltage = regulator_list_voltage_linear, }; -static struct regulator_ops rt5033_buck_ops = { +static const struct regulator_ops rt5033_buck_ops = { .is_enabled = regulator_is_enabled_regmap, .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, diff --git a/drivers/regulator/s2mpa01.c b/drivers/regulator/s2mpa01.c index 095d25f3d2ea..58a1fe583a6c 100644 --- a/drivers/regulator/s2mpa01.c +++ b/drivers/regulator/s2mpa01.c @@ -298,13 +298,13 @@ static const struct regulator_desc regulators[] = { regulator_desc_ldo(2, STEP_50_MV), regulator_desc_ldo(3, STEP_50_MV), regulator_desc_ldo(4, STEP_50_MV), - regulator_desc_ldo(5, STEP_50_MV), + regulator_desc_ldo(5, STEP_25_MV), regulator_desc_ldo(6, STEP_25_MV), regulator_desc_ldo(7, STEP_50_MV), regulator_desc_ldo(8, STEP_50_MV), regulator_desc_ldo(9, STEP_50_MV), regulator_desc_ldo(10, STEP_50_MV), - regulator_desc_ldo(11, STEP_25_MV), + regulator_desc_ldo(11, STEP_50_MV), regulator_desc_ldo(12, STEP_50_MV), regulator_desc_ldo(13, STEP_50_MV), regulator_desc_ldo(14, STEP_50_MV), @@ -315,11 +315,11 @@ static const struct regulator_desc regulators[] = { regulator_desc_ldo(19, STEP_50_MV), regulator_desc_ldo(20, STEP_50_MV), regulator_desc_ldo(21, STEP_50_MV), - regulator_desc_ldo(22, STEP_25_MV), - regulator_desc_ldo(23, STEP_25_MV), + regulator_desc_ldo(22, STEP_50_MV), + regulator_desc_ldo(23, STEP_50_MV), regulator_desc_ldo(24, STEP_50_MV), regulator_desc_ldo(25, STEP_50_MV), - regulator_desc_ldo(26, STEP_50_MV), + regulator_desc_ldo(26, STEP_25_MV), regulator_desc_buck1_4(1), regulator_desc_buck1_4(2), regulator_desc_buck1_4(3), diff --git a/drivers/regulator/s2mps11.c b/drivers/regulator/s2mps11.c index ee4a23ab0663..134c62db36c5 100644 --- a/drivers/regulator/s2mps11.c +++ b/drivers/regulator/s2mps11.c @@ -362,7 +362,7 @@ static const struct regulator_desc s2mps11_regulators[] = { regulator_desc_s2mps11_ldo(32, STEP_50_MV), regulator_desc_s2mps11_ldo(33, STEP_50_MV), regulator_desc_s2mps11_ldo(34, STEP_50_MV), - regulator_desc_s2mps11_ldo(35, STEP_50_MV), + regulator_desc_s2mps11_ldo(35, STEP_25_MV), regulator_desc_s2mps11_ldo(36, STEP_50_MV), regulator_desc_s2mps11_ldo(37, STEP_50_MV), regulator_desc_s2mps11_ldo(38, STEP_50_MV), @@ -372,8 +372,8 @@ static const struct regulator_desc s2mps11_regulators[] = { regulator_desc_s2mps11_buck1_4(4), regulator_desc_s2mps11_buck5, regulator_desc_s2mps11_buck67810(6, MIN_600_MV, STEP_6_25_MV), - regulator_desc_s2mps11_buck67810(7, MIN_600_MV, STEP_6_25_MV), - regulator_desc_s2mps11_buck67810(8, MIN_600_MV, STEP_6_25_MV), + regulator_desc_s2mps11_buck67810(7, MIN_600_MV, STEP_12_5_MV), + regulator_desc_s2mps11_buck67810(8, MIN_600_MV, STEP_12_5_MV), regulator_desc_s2mps11_buck9, regulator_desc_s2mps11_buck67810(10, MIN_750_MV, STEP_12_5_MV), }; diff --git a/drivers/regulator/s5m8767.c b/drivers/regulator/s5m8767.c index b581f01f3395..bb9d1a083299 100644 --- a/drivers/regulator/s5m8767.c +++ b/drivers/regulator/s5m8767.c @@ -115,7 +115,7 @@ static const struct sec_voltage_desc *reg_voltage_map[] = { [S5M8767_BUCK9] = &buck_voltage_val3, }; -static unsigned int s5m8767_opmode_reg[][4] = { +static const unsigned int s5m8767_opmode_reg[][4] = { /* {OFF, ON, LOWPOWER, SUSPEND} */ /* LDO1 ... LDO28 */ {0x0, 0x3, 0x2, 0x1}, /* LDO1 */ @@ -339,13 +339,9 @@ static int s5m8767_set_voltage_time_sel(struct regulator_dev *rdev, unsigned int new_sel) { struct s5m8767_info *s5m8767 = rdev_get_drvdata(rdev); - const struct sec_voltage_desc *desc; - int reg_id = rdev_get_id(rdev); - - desc = reg_voltage_map[reg_id]; if ((old_sel < new_sel) && s5m8767->ramp_delay) - return DIV_ROUND_UP(desc->step * (new_sel - old_sel), + return DIV_ROUND_UP(rdev->desc->uV_step * (new_sel - old_sel), s5m8767->ramp_delay * 1000); return 0; } diff --git a/drivers/regulator/stm32-vrefbuf.c b/drivers/regulator/stm32-vrefbuf.c index e0a9c445ed67..ba2f24949dc9 100644 --- a/drivers/regulator/stm32-vrefbuf.c +++ b/drivers/regulator/stm32-vrefbuf.c @@ -15,6 +15,7 @@ #include <linux/platform_device.h> #include <linux/regulator/driver.h> #include <linux/regulator/of_regulator.h> +#include <linux/pm_runtime.h> /* STM32 VREFBUF registers */ #define STM32_VREFBUF_CSR 0x00 @@ -25,9 +26,12 @@ #define STM32_HIZ BIT(1) #define STM32_ENVR BIT(0) +#define STM32_VREFBUF_AUTO_SUSPEND_DELAY_MS 10 + struct stm32_vrefbuf { void __iomem *base; struct clk *clk; + struct device *dev; }; static const unsigned int stm32_vrefbuf_voltages[] = { @@ -38,9 +42,16 @@ static const unsigned int stm32_vrefbuf_voltages[] = { static int stm32_vrefbuf_enable(struct regulator_dev *rdev) { struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); - u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + u32 val; int ret; + ret = pm_runtime_get_sync(priv->dev); + if (ret < 0) { + pm_runtime_put_noidle(priv->dev); + return ret; + } + + val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); val = (val & ~STM32_HIZ) | STM32_ENVR; writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); @@ -59,45 +70,95 @@ static int stm32_vrefbuf_enable(struct regulator_dev *rdev) writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); } + pm_runtime_mark_last_busy(priv->dev); + pm_runtime_put_autosuspend(priv->dev); + return ret; } static int stm32_vrefbuf_disable(struct regulator_dev *rdev) { struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); - u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + u32 val; + int ret; + ret = pm_runtime_get_sync(priv->dev); + if (ret < 0) { + pm_runtime_put_noidle(priv->dev); + return ret; + } + + val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); val = (val & ~STM32_ENVR) | STM32_HIZ; writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + pm_runtime_mark_last_busy(priv->dev); + pm_runtime_put_autosuspend(priv->dev); + return 0; } static int stm32_vrefbuf_is_enabled(struct regulator_dev *rdev) { struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + int ret; + + ret = pm_runtime_get_sync(priv->dev); + if (ret < 0) { + pm_runtime_put_noidle(priv->dev); + return ret; + } + + ret = readl_relaxed(priv->base + STM32_VREFBUF_CSR) & STM32_ENVR; - return readl_relaxed(priv->base + STM32_VREFBUF_CSR) & STM32_ENVR; + pm_runtime_mark_last_busy(priv->dev); + pm_runtime_put_autosuspend(priv->dev); + + return ret; } static int stm32_vrefbuf_set_voltage_sel(struct regulator_dev *rdev, unsigned sel) { struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); - u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + u32 val; + int ret; + ret = pm_runtime_get_sync(priv->dev); + if (ret < 0) { + pm_runtime_put_noidle(priv->dev); + return ret; + } + + val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); val = (val & ~STM32_VRS) | FIELD_PREP(STM32_VRS, sel); writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + pm_runtime_mark_last_busy(priv->dev); + pm_runtime_put_autosuspend(priv->dev); + return 0; } static int stm32_vrefbuf_get_voltage_sel(struct regulator_dev *rdev) { struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); - u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + u32 val; + int ret; - return FIELD_GET(STM32_VRS, val); + ret = pm_runtime_get_sync(priv->dev); + if (ret < 0) { + pm_runtime_put_noidle(priv->dev); + return ret; + } + + val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + ret = FIELD_GET(STM32_VRS, val); + + pm_runtime_mark_last_busy(priv->dev); + pm_runtime_put_autosuspend(priv->dev); + + return ret; } static const struct regulator_ops stm32_vrefbuf_volt_ops = { @@ -130,6 +191,7 @@ static int stm32_vrefbuf_probe(struct platform_device *pdev) priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); if (!priv) return -ENOMEM; + priv->dev = &pdev->dev; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); priv->base = devm_ioremap_resource(&pdev->dev, res); @@ -140,10 +202,17 @@ static int stm32_vrefbuf_probe(struct platform_device *pdev) if (IS_ERR(priv->clk)) return PTR_ERR(priv->clk); + pm_runtime_get_noresume(&pdev->dev); + pm_runtime_set_active(&pdev->dev); + pm_runtime_set_autosuspend_delay(&pdev->dev, + STM32_VREFBUF_AUTO_SUSPEND_DELAY_MS); + pm_runtime_use_autosuspend(&pdev->dev); + pm_runtime_enable(&pdev->dev); + ret = clk_prepare_enable(priv->clk); if (ret) { dev_err(&pdev->dev, "clk prepare failed with error %d\n", ret); - return ret; + goto err_pm_stop; } config.dev = &pdev->dev; @@ -161,10 +230,17 @@ static int stm32_vrefbuf_probe(struct platform_device *pdev) } platform_set_drvdata(pdev, rdev); + pm_runtime_mark_last_busy(&pdev->dev); + pm_runtime_put_autosuspend(&pdev->dev); + return 0; err_clk_dis: clk_disable_unprepare(priv->clk); +err_pm_stop: + pm_runtime_disable(&pdev->dev); + pm_runtime_set_suspended(&pdev->dev); + pm_runtime_put_noidle(&pdev->dev); return ret; } @@ -174,12 +250,42 @@ static int stm32_vrefbuf_remove(struct platform_device *pdev) struct regulator_dev *rdev = platform_get_drvdata(pdev); struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + pm_runtime_get_sync(&pdev->dev); regulator_unregister(rdev); clk_disable_unprepare(priv->clk); + pm_runtime_disable(&pdev->dev); + pm_runtime_set_suspended(&pdev->dev); + pm_runtime_put_noidle(&pdev->dev); return 0; }; +static int __maybe_unused stm32_vrefbuf_runtime_suspend(struct device *dev) +{ + struct regulator_dev *rdev = dev_get_drvdata(dev); + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + + clk_disable_unprepare(priv->clk); + + return 0; +} + +static int __maybe_unused stm32_vrefbuf_runtime_resume(struct device *dev) +{ + struct regulator_dev *rdev = dev_get_drvdata(dev); + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + + return clk_prepare_enable(priv->clk); +} + +static const struct dev_pm_ops stm32_vrefbuf_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, + pm_runtime_force_resume) + SET_RUNTIME_PM_OPS(stm32_vrefbuf_runtime_suspend, + stm32_vrefbuf_runtime_resume, + NULL) +}; + static const struct of_device_id stm32_vrefbuf_of_match[] = { { .compatible = "st,stm32-vrefbuf", }, {}, @@ -192,6 +298,7 @@ static struct platform_driver stm32_vrefbuf_driver = { .driver = { .name = "stm32-vrefbuf", .of_match_table = of_match_ptr(stm32_vrefbuf_of_match), + .pm = &stm32_vrefbuf_pm_ops, }, }; module_platform_driver(stm32_vrefbuf_driver); diff --git a/drivers/regulator/stpmic1_regulator.c b/drivers/regulator/stpmic1_regulator.c index 16ba0297f709..f09061473613 100644 --- a/drivers/regulator/stpmic1_regulator.c +++ b/drivers/regulator/stpmic1_regulator.c @@ -12,8 +12,10 @@ #include <linux/regulator/machine.h> #include <linux/regulator/of_regulator.h> +#include <dt-bindings/mfd/st,stpmic1.h> + /** - * stpmic1 regulator description + * stpmic1 regulator description: this structure is used as driver data * @desc: regulator framework description * @mask_reset_reg: mask reset register address * @mask_reset_mask: mask rank and mask reset register mask @@ -28,28 +30,9 @@ struct stpmic1_regulator_cfg { u8 icc_mask; }; -/** - * stpmic1 regulator data: this structure is used as driver data - * @regul_id: regulator id - * @reg_node: DT node of regulator (unused on non-DT platforms) - * @cfg: stpmic specific regulator description - * @mask_reset: mask_reset bit value - * @irq_curlim: current limit interrupt number - * @regmap: point to parent regmap structure - */ -struct stpmic1_regulator { - unsigned int regul_id; - struct device_node *reg_node; - struct stpmic1_regulator_cfg *cfg; - u8 mask_reset; - int irq_curlim; - struct regmap *regmap; -}; - static int stpmic1_set_mode(struct regulator_dev *rdev, unsigned int mode); static unsigned int stpmic1_get_mode(struct regulator_dev *rdev); static int stpmic1_set_icc(struct regulator_dev *rdev); -static int stpmic1_regulator_parse_dt(void *driver_data); static unsigned int stpmic1_map_mode(unsigned int mode); enum { @@ -72,15 +55,13 @@ enum { /* Enable time worst case is 5000mV/(2250uV/uS) */ #define PMIC_ENABLE_TIME_US 2200 -#define STPMIC1_BUCK_MODE_NORMAL 0 -#define STPMIC1_BUCK_MODE_LP BUCK_HPLP_ENABLE_MASK - -struct regulator_linear_range buck1_ranges[] = { - REGULATOR_LINEAR_RANGE(600000, 0, 30, 25000), - REGULATOR_LINEAR_RANGE(1350000, 31, 63, 0), +static const struct regulator_linear_range buck1_ranges[] = { + REGULATOR_LINEAR_RANGE(725000, 0, 4, 0), + REGULATOR_LINEAR_RANGE(725000, 5, 36, 25000), + REGULATOR_LINEAR_RANGE(1500000, 37, 63, 0), }; -struct regulator_linear_range buck2_ranges[] = { +static const struct regulator_linear_range buck2_ranges[] = { REGULATOR_LINEAR_RANGE(1000000, 0, 17, 0), REGULATOR_LINEAR_RANGE(1050000, 18, 19, 0), REGULATOR_LINEAR_RANGE(1100000, 20, 21, 0), @@ -94,7 +75,7 @@ struct regulator_linear_range buck2_ranges[] = { REGULATOR_LINEAR_RANGE(1500000, 36, 63, 0), }; -struct regulator_linear_range buck3_ranges[] = { +static const struct regulator_linear_range buck3_ranges[] = { REGULATOR_LINEAR_RANGE(1000000, 0, 19, 0), REGULATOR_LINEAR_RANGE(1100000, 20, 23, 0), REGULATOR_LINEAR_RANGE(1200000, 24, 27, 0), @@ -102,10 +83,9 @@ struct regulator_linear_range buck3_ranges[] = { REGULATOR_LINEAR_RANGE(1400000, 32, 35, 0), REGULATOR_LINEAR_RANGE(1500000, 36, 55, 100000), REGULATOR_LINEAR_RANGE(3400000, 56, 63, 0), - }; -struct regulator_linear_range buck4_ranges[] = { +static const struct regulator_linear_range buck4_ranges[] = { REGULATOR_LINEAR_RANGE(600000, 0, 27, 25000), REGULATOR_LINEAR_RANGE(1300000, 28, 29, 0), REGULATOR_LINEAR_RANGE(1350000, 30, 31, 0), @@ -113,24 +93,21 @@ struct regulator_linear_range buck4_ranges[] = { REGULATOR_LINEAR_RANGE(1450000, 34, 35, 0), REGULATOR_LINEAR_RANGE(1500000, 36, 60, 100000), REGULATOR_LINEAR_RANGE(3900000, 61, 63, 0), - }; -struct regulator_linear_range ldo1_ranges[] = { +static const struct regulator_linear_range ldo1_ranges[] = { REGULATOR_LINEAR_RANGE(1700000, 0, 7, 0), REGULATOR_LINEAR_RANGE(1700000, 8, 24, 100000), REGULATOR_LINEAR_RANGE(3300000, 25, 31, 0), - }; -struct regulator_linear_range ldo2_ranges[] = { +static const struct regulator_linear_range ldo2_ranges[] = { REGULATOR_LINEAR_RANGE(1700000, 0, 7, 0), REGULATOR_LINEAR_RANGE(1700000, 8, 24, 100000), REGULATOR_LINEAR_RANGE(3300000, 25, 30, 0), - }; -struct regulator_linear_range ldo3_ranges[] = { +static const struct regulator_linear_range ldo3_ranges[] = { REGULATOR_LINEAR_RANGE(1700000, 0, 7, 0), REGULATOR_LINEAR_RANGE(1700000, 8, 24, 100000), REGULATOR_LINEAR_RANGE(3300000, 25, 30, 0), @@ -138,18 +115,18 @@ struct regulator_linear_range ldo3_ranges[] = { REGULATOR_LINEAR_RANGE(500000, 31, 31, 0), }; -struct regulator_linear_range ldo5_ranges[] = { +static const struct regulator_linear_range ldo5_ranges[] = { REGULATOR_LINEAR_RANGE(1700000, 0, 7, 0), REGULATOR_LINEAR_RANGE(1700000, 8, 30, 100000), REGULATOR_LINEAR_RANGE(3900000, 31, 31, 0), }; -struct regulator_linear_range ldo6_ranges[] = { +static const struct regulator_linear_range ldo6_ranges[] = { REGULATOR_LINEAR_RANGE(900000, 0, 24, 100000), REGULATOR_LINEAR_RANGE(3300000, 25, 31, 0), }; -static struct regulator_ops stpmic1_ldo_ops = { +static const struct regulator_ops stpmic1_ldo_ops = { .list_voltage = regulator_list_voltage_linear_range, .map_voltage = regulator_map_voltage_linear_range, .is_enabled = regulator_is_enabled_regmap, @@ -157,11 +134,10 @@ static struct regulator_ops stpmic1_ldo_ops = { .disable = regulator_disable_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, .set_voltage_sel = regulator_set_voltage_sel_regmap, - .set_pull_down = regulator_set_pull_down_regmap, .set_over_current_protection = stpmic1_set_icc, }; -static struct regulator_ops stpmic1_ldo3_ops = { +static const struct regulator_ops stpmic1_ldo3_ops = { .list_voltage = regulator_list_voltage_linear_range, .map_voltage = regulator_map_voltage_iterate, .is_enabled = regulator_is_enabled_regmap, @@ -169,21 +145,19 @@ static struct regulator_ops stpmic1_ldo3_ops = { .disable = regulator_disable_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, .set_voltage_sel = regulator_set_voltage_sel_regmap, - .set_pull_down = regulator_set_pull_down_regmap, .get_bypass = regulator_get_bypass_regmap, .set_bypass = regulator_set_bypass_regmap, .set_over_current_protection = stpmic1_set_icc, }; -static struct regulator_ops stpmic1_ldo4_fixed_regul_ops = { +static const struct regulator_ops stpmic1_ldo4_fixed_regul_ops = { .is_enabled = regulator_is_enabled_regmap, .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, - .set_pull_down = regulator_set_pull_down_regmap, .set_over_current_protection = stpmic1_set_icc, }; -static struct regulator_ops stpmic1_buck_ops = { +static const struct regulator_ops stpmic1_buck_ops = { .list_voltage = regulator_list_voltage_linear_range, .map_voltage = regulator_map_voltage_linear_range, .is_enabled = regulator_is_enabled_regmap, @@ -197,20 +171,27 @@ static struct regulator_ops stpmic1_buck_ops = { .set_over_current_protection = stpmic1_set_icc, }; -static struct regulator_ops stpmic1_vref_ddr_ops = { +static const struct regulator_ops stpmic1_vref_ddr_ops = { .is_enabled = regulator_is_enabled_regmap, .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, - .set_pull_down = regulator_set_pull_down_regmap, }; -static struct regulator_ops stpmic1_switch_regul_ops = { +static const struct regulator_ops stpmic1_boost_regul_ops = { .is_enabled = regulator_is_enabled_regmap, .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .set_over_current_protection = stpmic1_set_icc, }; +static const struct regulator_ops stpmic1_switch_regul_ops = { + .is_enabled = regulator_is_enabled_regmap, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .set_over_current_protection = stpmic1_set_icc, + .set_active_discharge = regulator_set_active_discharge_regmap, +}; + #define REG_LDO(ids, base) { \ .name = #ids, \ .id = STPMIC1_##ids, \ @@ -227,8 +208,6 @@ static struct regulator_ops stpmic1_switch_regul_ops = { .enable_val = 1, \ .disable_val = 0, \ .enable_time = PMIC_ENABLE_TIME_US, \ - .pull_down_reg = ids##_PULL_DOWN_REG, \ - .pull_down_mask = ids##_PULL_DOWN_MASK, \ .supply_name = #base, \ } @@ -252,8 +231,6 @@ static struct regulator_ops stpmic1_switch_regul_ops = { .bypass_mask = LDO_BYPASS_MASK, \ .bypass_val_on = LDO_BYPASS_MASK, \ .bypass_val_off = 0, \ - .pull_down_reg = ids##_PULL_DOWN_REG, \ - .pull_down_mask = ids##_PULL_DOWN_MASK, \ .supply_name = #base, \ } @@ -271,8 +248,6 @@ static struct regulator_ops stpmic1_switch_regul_ops = { .enable_val = 1, \ .disable_val = 0, \ .enable_time = PMIC_ENABLE_TIME_US, \ - .pull_down_reg = ids##_PULL_DOWN_REG, \ - .pull_down_mask = ids##_PULL_DOWN_MASK, \ .supply_name = #base, \ } @@ -312,12 +287,47 @@ static struct regulator_ops stpmic1_switch_regul_ops = { .enable_val = 1, \ .disable_val = 0, \ .enable_time = PMIC_ENABLE_TIME_US, \ - .pull_down_reg = ids##_PULL_DOWN_REG, \ - .pull_down_mask = ids##_PULL_DOWN_MASK, \ .supply_name = #base, \ } -#define REG_SWITCH(ids, base, reg, mask, val) { \ +#define REG_BOOST(ids, base) { \ + .name = #ids, \ + .id = STPMIC1_##ids, \ + .n_voltages = 1, \ + .ops = &stpmic1_boost_regul_ops, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .min_uV = 0, \ + .fixed_uV = 5000000, \ + .enable_reg = BST_SW_CR, \ + .enable_mask = BOOST_ENABLED, \ + .enable_val = BOOST_ENABLED, \ + .disable_val = 0, \ + .enable_time = PMIC_ENABLE_TIME_US, \ + .supply_name = #base, \ +} + +#define REG_VBUS_OTG(ids, base) { \ + .name = #ids, \ + .id = STPMIC1_##ids, \ + .n_voltages = 1, \ + .ops = &stpmic1_switch_regul_ops, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .min_uV = 0, \ + .fixed_uV = 5000000, \ + .enable_reg = BST_SW_CR, \ + .enable_mask = USBSW_OTG_SWITCH_ENABLED, \ + .enable_val = USBSW_OTG_SWITCH_ENABLED, \ + .disable_val = 0, \ + .enable_time = PMIC_ENABLE_TIME_US, \ + .supply_name = #base, \ + .active_discharge_reg = BST_SW_CR, \ + .active_discharge_mask = VBUS_OTG_DISCHARGE, \ + .active_discharge_on = VBUS_OTG_DISCHARGE, \ +} + +#define REG_SW_OUT(ids, base) { \ .name = #ids, \ .id = STPMIC1_##ids, \ .n_voltages = 1, \ @@ -326,15 +336,18 @@ static struct regulator_ops stpmic1_switch_regul_ops = { .owner = THIS_MODULE, \ .min_uV = 0, \ .fixed_uV = 5000000, \ - .enable_reg = (reg), \ - .enable_mask = (mask), \ - .enable_val = (val), \ + .enable_reg = BST_SW_CR, \ + .enable_mask = SWIN_SWOUT_ENABLED, \ + .enable_val = SWIN_SWOUT_ENABLED, \ .disable_val = 0, \ .enable_time = PMIC_ENABLE_TIME_US, \ .supply_name = #base, \ + .active_discharge_reg = BST_SW_CR, \ + .active_discharge_mask = SW_OUT_DISCHARGE, \ + .active_discharge_on = SW_OUT_DISCHARGE, \ } -struct stpmic1_regulator_cfg stpmic1_regulator_cfgs[] = { +static const struct stpmic1_regulator_cfg stpmic1_regulator_cfgs[] = { [STPMIC1_BUCK1] = { .desc = REG_BUCK(BUCK1, buck1), .icc_reg = BUCKS_ICCTO_CR, @@ -411,23 +424,17 @@ struct stpmic1_regulator_cfg stpmic1_regulator_cfgs[] = { .mask_reset_mask = BIT(6), }, [STPMIC1_BOOST] = { - .desc = REG_SWITCH(BOOST, boost, BST_SW_CR, - BOOST_ENABLED, - BOOST_ENABLED), + .desc = REG_BOOST(BOOST, boost), .icc_reg = BUCKS_ICCTO_CR, .icc_mask = BIT(6), }, [STPMIC1_VBUS_OTG] = { - .desc = REG_SWITCH(VBUS_OTG, pwr_sw1, BST_SW_CR, - USBSW_OTG_SWITCH_ENABLED, - USBSW_OTG_SWITCH_ENABLED), + .desc = REG_VBUS_OTG(VBUS_OTG, pwr_sw1), .icc_reg = BUCKS_ICCTO_CR, .icc_mask = BIT(4), }, [STPMIC1_SW_OUT] = { - .desc = REG_SWITCH(SW_OUT, pwr_sw2, BST_SW_CR, - SWIN_SWOUT_ENABLED, - SWIN_SWOUT_ENABLED), + .desc = REG_SW_OUT(SW_OUT, pwr_sw2), .icc_reg = BUCKS_ICCTO_CR, .icc_mask = BIT(5), }, @@ -448,8 +455,9 @@ static unsigned int stpmic1_map_mode(unsigned int mode) static unsigned int stpmic1_get_mode(struct regulator_dev *rdev) { int value; + struct regmap *regmap = rdev_get_regmap(rdev); - regmap_read(rdev->regmap, rdev->desc->enable_reg, &value); + regmap_read(regmap, rdev->desc->enable_reg, &value); if (value & STPMIC1_BUCK_MODE_LP) return REGULATOR_MODE_STANDBY; @@ -460,6 +468,7 @@ static unsigned int stpmic1_get_mode(struct regulator_dev *rdev) static int stpmic1_set_mode(struct regulator_dev *rdev, unsigned int mode) { int value; + struct regmap *regmap = rdev_get_regmap(rdev); switch (mode) { case REGULATOR_MODE_NORMAL: @@ -472,17 +481,18 @@ static int stpmic1_set_mode(struct regulator_dev *rdev, unsigned int mode) return -EINVAL; } - return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, + return regmap_update_bits(regmap, rdev->desc->enable_reg, STPMIC1_BUCK_MODE_LP, value); } static int stpmic1_set_icc(struct regulator_dev *rdev) { - struct stpmic1_regulator *regul = rdev_get_drvdata(rdev); + struct stpmic1_regulator_cfg *cfg = rdev_get_drvdata(rdev); + struct regmap *regmap = rdev_get_regmap(rdev); /* enable switch off in case of over current */ - return regmap_update_bits(regul->regmap, regul->cfg->icc_reg, - regul->cfg->icc_mask, regul->cfg->icc_mask); + return regmap_update_bits(regmap, cfg->icc_reg, cfg->icc_mask, + cfg->icc_mask); } static irqreturn_t stpmic1_curlim_irq_handler(int irq, void *data) @@ -501,46 +511,13 @@ static irqreturn_t stpmic1_curlim_irq_handler(int irq, void *data) return IRQ_HANDLED; } -static int stpmic1_regulator_init(struct platform_device *pdev, - struct regulator_dev *rdev) -{ - struct stpmic1_regulator *regul = rdev_get_drvdata(rdev); - int ret = 0; - - /* set mask reset */ - if (regul->mask_reset && regul->cfg->mask_reset_reg != 0) { - ret = regmap_update_bits(regul->regmap, - regul->cfg->mask_reset_reg, - regul->cfg->mask_reset_mask, - regul->cfg->mask_reset_mask); - if (ret) { - dev_err(&pdev->dev, "set mask reset failed\n"); - return ret; - } - } - - /* setup an irq handler for over-current detection */ - if (regul->irq_curlim > 0) { - ret = devm_request_threaded_irq(&pdev->dev, - regul->irq_curlim, NULL, - stpmic1_curlim_irq_handler, - IRQF_ONESHOT | IRQF_SHARED, - pdev->name, rdev); - if (ret) { - dev_err(&pdev->dev, "Request IRQ failed\n"); - return ret; - } - } - return 0; -} - #define MATCH(_name, _id) \ [STPMIC1_##_id] = { \ .name = #_name, \ .desc = &stpmic1_regulator_cfgs[STPMIC1_##_id].desc, \ } -static struct of_regulator_match stpmic1_regulators_matches[] = { +static struct of_regulator_match stpmic1_matches[] = { MATCH(buck1, BUCK1), MATCH(buck2, BUCK2), MATCH(buck3, BUCK3), @@ -557,94 +534,75 @@ static struct of_regulator_match stpmic1_regulators_matches[] = { MATCH(pwr_sw2, SW_OUT), }; -static int stpmic1_regulator_parse_dt(void *driver_data) -{ - struct stpmic1_regulator *regul = - (struct stpmic1_regulator *)driver_data; - - if (!regul) - return -EINVAL; - - if (of_get_property(regul->reg_node, "st,mask-reset", NULL)) - regul->mask_reset = 1; - - regul->irq_curlim = of_irq_get(regul->reg_node, 0); - - return 0; -} - -static struct -regulator_dev *stpmic1_regulator_register(struct platform_device *pdev, int id, - struct regulator_init_data *init_data, - struct stpmic1_regulator *regul) +static int stpmic1_regulator_register(struct platform_device *pdev, int id, + struct of_regulator_match *match, + const struct stpmic1_regulator_cfg *cfg) { struct stpmic1 *pmic_dev = dev_get_drvdata(pdev->dev.parent); struct regulator_dev *rdev; struct regulator_config config = {}; + int ret = 0; + int irq; config.dev = &pdev->dev; - config.init_data = init_data; - config.of_node = stpmic1_regulators_matches[id].of_node; + config.init_data = match->init_data; + config.of_node = match->of_node; config.regmap = pmic_dev->regmap; - config.driver_data = regul; - - regul->regul_id = id; - regul->reg_node = config.of_node; - regul->cfg = &stpmic1_regulator_cfgs[id]; - regul->regmap = pmic_dev->regmap; + config.driver_data = (void *)cfg; - rdev = devm_regulator_register(&pdev->dev, ®ul->cfg->desc, &config); + rdev = devm_regulator_register(&pdev->dev, &cfg->desc, &config); if (IS_ERR(rdev)) { dev_err(&pdev->dev, "failed to register %s regulator\n", - regul->cfg->desc.name); + cfg->desc.name); + return PTR_ERR(rdev); + } + + /* set mask reset */ + if (of_get_property(config.of_node, "st,mask-reset", NULL) && + cfg->mask_reset_reg != 0) { + ret = regmap_update_bits(pmic_dev->regmap, + cfg->mask_reset_reg, + cfg->mask_reset_mask, + cfg->mask_reset_mask); + if (ret) { + dev_err(&pdev->dev, "set mask reset failed\n"); + return ret; + } } - return rdev; + /* setup an irq handler for over-current detection */ + irq = of_irq_get(config.of_node, 0); + if (irq > 0) { + ret = devm_request_threaded_irq(&pdev->dev, + irq, NULL, + stpmic1_curlim_irq_handler, + IRQF_ONESHOT | IRQF_SHARED, + pdev->name, rdev); + if (ret) { + dev_err(&pdev->dev, "Request IRQ failed\n"); + return ret; + } + } + return 0; } static int stpmic1_regulator_probe(struct platform_device *pdev) { - struct regulator_dev *rdev; - struct stpmic1_regulator *regul; - struct regulator_init_data *init_data; - struct device_node *np; int i, ret; - np = pdev->dev.of_node; - - ret = of_regulator_match(&pdev->dev, np, - stpmic1_regulators_matches, - ARRAY_SIZE(stpmic1_regulators_matches)); + ret = of_regulator_match(&pdev->dev, pdev->dev.of_node, stpmic1_matches, + ARRAY_SIZE(stpmic1_matches)); if (ret < 0) { dev_err(&pdev->dev, "Error in PMIC regulator device tree node"); return ret; } - regul = devm_kzalloc(&pdev->dev, ARRAY_SIZE(stpmic1_regulator_cfgs) * - sizeof(struct stpmic1_regulator), - GFP_KERNEL); - if (!regul) - return -ENOMEM; - for (i = 0; i < ARRAY_SIZE(stpmic1_regulator_cfgs); i++) { - /* Parse DT & find regulators to register */ - init_data = stpmic1_regulators_matches[i].init_data; - if (init_data) - init_data->regulator_init = &stpmic1_regulator_parse_dt; - - rdev = stpmic1_regulator_register(pdev, i, init_data, regul); - if (IS_ERR(rdev)) - return PTR_ERR(rdev); - - ret = stpmic1_regulator_init(pdev, rdev); - if (ret) { - dev_err(&pdev->dev, - "failed to initialize regulator %d\n", ret); + ret = stpmic1_regulator_register(pdev, i, &stpmic1_matches[i], + &stpmic1_regulator_cfgs[i]); + if (ret < 0) return ret; - } - - regul++; } dev_dbg(&pdev->dev, "stpmic1_regulator driver probed\n"); diff --git a/drivers/regulator/tps65218-regulator.c b/drivers/regulator/tps65218-regulator.c index 6209beee1018..95708d34876b 100644 --- a/drivers/regulator/tps65218-regulator.c +++ b/drivers/regulator/tps65218-regulator.c @@ -188,7 +188,8 @@ static struct regulator_ops tps65218_ldo1_dcdc34_ops = { .set_suspend_disable = tps65218_pmic_set_suspend_disable, }; -static const int ls3_currents[] = { 100, 200, 500, 1000 }; +static const int ls3_currents[] = { 100000, 200000, 500000, 1000000 }; + static int tps65218_pmic_set_input_current_lim(struct regulator_dev *dev, int lim_uA) @@ -204,7 +205,8 @@ static int tps65218_pmic_set_input_current_lim(struct regulator_dev *dev, return -EINVAL; return tps65218_set_bits(tps, dev->desc->csel_reg, dev->desc->csel_mask, - index << 2, TPS65218_PROTECT_L1); + index << __builtin_ctz(dev->desc->csel_mask), + TPS65218_PROTECT_L1); } static int tps65218_pmic_set_current_limit(struct regulator_dev *dev, @@ -214,7 +216,7 @@ static int tps65218_pmic_set_current_limit(struct regulator_dev *dev, unsigned int num_currents = ARRAY_SIZE(ls3_currents); struct tps65218 *tps = rdev_get_drvdata(dev); - while (index < num_currents && ls3_currents[index] < max_uA) + while (index < num_currents && ls3_currents[index] <= max_uA) index++; index--; @@ -223,7 +225,8 @@ static int tps65218_pmic_set_current_limit(struct regulator_dev *dev, return -EINVAL; return tps65218_set_bits(tps, dev->desc->csel_reg, dev->desc->csel_mask, - index << 2, TPS65218_PROTECT_L1); + index << __builtin_ctz(dev->desc->csel_mask), + TPS65218_PROTECT_L1); } static int tps65218_pmic_get_current_limit(struct regulator_dev *dev) @@ -236,12 +239,13 @@ static int tps65218_pmic_get_current_limit(struct regulator_dev *dev) if (retval < 0) return retval; - index = (index & dev->desc->csel_mask) >> 2; + index = (index & dev->desc->csel_mask) >> + __builtin_ctz(dev->desc->csel_mask); return ls3_currents[index]; } -static struct regulator_ops tps65218_ls3_ops = { +static struct regulator_ops tps65218_ls23_ops = { .is_enabled = regulator_is_enabled_regmap, .enable = tps65218_pmic_enable, .disable = tps65218_pmic_disable, @@ -303,8 +307,13 @@ static const struct regulator_desc regulators[] = { TPS65218_ENABLE2_LDO1_EN, 0, 0, ldo1_dcdc3_ranges, 2, 0, 0, TPS65218_REG_SEQ6, TPS65218_SEQ6_LDO1_SEQ_MASK), + TPS65218_REGULATOR("LS2", "regulator-ls2", TPS65218_LS_2, + REGULATOR_CURRENT, tps65218_ls23_ops, 0, 0, 0, + TPS65218_REG_ENABLE2, TPS65218_ENABLE2_LS2_EN, + TPS65218_REG_CONFIG2, TPS65218_CONFIG2_LS2ILIM_MASK, + NULL, 0, 0, 0, 0, 0), TPS65218_REGULATOR("LS3", "regulator-ls3", TPS65218_LS_3, - REGULATOR_CURRENT, tps65218_ls3_ops, 0, 0, 0, + REGULATOR_CURRENT, tps65218_ls23_ops, 0, 0, 0, TPS65218_REG_ENABLE2, TPS65218_ENABLE2_LS3_EN, TPS65218_REG_CONFIG2, TPS65218_CONFIG2_LS3ILIM_MASK, NULL, 0, 0, 0, 0, 0), diff --git a/drivers/regulator/twl-regulator.c b/drivers/regulator/twl-regulator.c index 884c7505ed91..402ea43c77d1 100644 --- a/drivers/regulator/twl-regulator.c +++ b/drivers/regulator/twl-regulator.c @@ -576,14 +576,9 @@ static int twlreg_probe(struct platform_device *pdev) struct regulator_init_data *initdata; struct regulation_constraints *c; struct regulator_dev *rdev; - const struct of_device_id *match; struct regulator_config config = { }; - match = of_match_device(twl_of_match, &pdev->dev); - if (!match) - return -ENODEV; - - template = match->data; + template = of_device_get_match_data(&pdev->dev); if (!template) return -ENODEV; diff --git a/drivers/regulator/twl6030-regulator.c b/drivers/regulator/twl6030-regulator.c index 219cbd910dbf..15f19df6bc5d 100644 --- a/drivers/regulator/twl6030-regulator.c +++ b/drivers/regulator/twl6030-regulator.c @@ -31,9 +31,6 @@ struct twlreg_info { /* twl resource ID, for resource control state machine */ u8 id; - /* chip constraints on regulator behavior */ - u16 min_mV; - u8 flags; /* used by regulator core */ @@ -247,32 +244,11 @@ static int twl6030coresmps_get_voltage(struct regulator_dev *rdev) return -ENODEV; } -static struct regulator_ops twl6030coresmps_ops = { +static const struct regulator_ops twl6030coresmps_ops = { .set_voltage = twl6030coresmps_set_voltage, .get_voltage = twl6030coresmps_get_voltage, }; -static int twl6030ldo_list_voltage(struct regulator_dev *rdev, unsigned sel) -{ - struct twlreg_info *info = rdev_get_drvdata(rdev); - - switch (sel) { - case 0: - return 0; - case 1 ... 24: - /* Linear mapping from 00000001 to 00011000: - * Absolute voltage value = 1.0 V + 0.1 V × (sel – 00000001) - */ - return (info->min_mV + 100 * (sel - 1)) * 1000; - case 25 ... 30: - return -EINVAL; - case 31: - return 2750000; - default: - return -EINVAL; - } -} - static int twl6030ldo_set_voltage_sel(struct regulator_dev *rdev, unsigned selector) { @@ -290,8 +266,8 @@ static int twl6030ldo_get_voltage_sel(struct regulator_dev *rdev) return vsel; } -static struct regulator_ops twl6030ldo_ops = { - .list_voltage = twl6030ldo_list_voltage, +static const struct regulator_ops twl6030ldo_ops = { + .list_voltage = regulator_list_voltage_linear_range, .set_voltage_sel = twl6030ldo_set_voltage_sel, .get_voltage_sel = twl6030ldo_get_voltage_sel, @@ -305,7 +281,7 @@ static struct regulator_ops twl6030ldo_ops = { .get_status = twl6030reg_get_status, }; -static struct regulator_ops twl6030fixed_ops = { +static const struct regulator_ops twl6030fixed_ops = { .list_voltage = regulator_list_voltage_linear, .enable = twl6030reg_enable, @@ -496,7 +472,7 @@ static int twl6030smps_get_voltage_sel(struct regulator_dev *rdev) return twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE_SMPS); } -static struct regulator_ops twlsmps_ops = { +static const struct regulator_ops twlsmps_ops = { .list_voltage = twl6030smps_list_voltage, .map_voltage = twl6030smps_map_voltage, @@ -513,6 +489,11 @@ static struct regulator_ops twlsmps_ops = { }; /*----------------------------------------------------------------------*/ +static const struct regulator_linear_range twl6030ldo_linear_range[] = { + REGULATOR_LINEAR_RANGE(0, 0, 0, 0), + REGULATOR_LINEAR_RANGE(1000000, 1, 24, 100000), + REGULATOR_LINEAR_RANGE(2750000, 31, 31, 0), +}; #define TWL6030_ADJUSTABLE_SMPS(label) \ static const struct twlreg_info TWL6030_INFO_##label = { \ @@ -525,28 +506,30 @@ static const struct twlreg_info TWL6030_INFO_##label = { \ }, \ } -#define TWL6030_ADJUSTABLE_LDO(label, offset, min_mVolts) \ +#define TWL6030_ADJUSTABLE_LDO(label, offset) \ static const struct twlreg_info TWL6030_INFO_##label = { \ .base = offset, \ - .min_mV = min_mVolts, \ .desc = { \ .name = #label, \ .id = TWL6030_REG_##label, \ .n_voltages = 32, \ + .linear_ranges = twl6030ldo_linear_range, \ + .n_linear_ranges = ARRAY_SIZE(twl6030ldo_linear_range), \ .ops = &twl6030ldo_ops, \ .type = REGULATOR_VOLTAGE, \ .owner = THIS_MODULE, \ }, \ } -#define TWL6032_ADJUSTABLE_LDO(label, offset, min_mVolts) \ +#define TWL6032_ADJUSTABLE_LDO(label, offset) \ static const struct twlreg_info TWL6032_INFO_##label = { \ .base = offset, \ - .min_mV = min_mVolts, \ .desc = { \ .name = #label, \ .id = TWL6032_REG_##label, \ .n_voltages = 32, \ + .linear_ranges = twl6030ldo_linear_range, \ + .n_linear_ranges = ARRAY_SIZE(twl6030ldo_linear_range), \ .ops = &twl6030ldo_ops, \ .type = REGULATOR_VOLTAGE, \ .owner = THIS_MODULE, \ @@ -557,7 +540,6 @@ static const struct twlreg_info TWL6032_INFO_##label = { \ static const struct twlreg_info TWLFIXED_INFO_##label = { \ .base = offset, \ .id = 0, \ - .min_mV = mVolts, \ .desc = { \ .name = #label, \ .id = TWL6030##_REG_##label, \ @@ -574,7 +556,6 @@ static const struct twlreg_info TWLFIXED_INFO_##label = { \ #define TWL6032_ADJUSTABLE_SMPS(label, offset) \ static const struct twlreg_info TWLSMPS_INFO_##label = { \ .base = offset, \ - .min_mV = 600, \ .desc = { \ .name = #label, \ .id = TWL6032_REG_##label, \ @@ -592,22 +573,22 @@ static const struct twlreg_info TWLSMPS_INFO_##label = { \ TWL6030_ADJUSTABLE_SMPS(VDD1); TWL6030_ADJUSTABLE_SMPS(VDD2); TWL6030_ADJUSTABLE_SMPS(VDD3); -TWL6030_ADJUSTABLE_LDO(VAUX1_6030, 0x54, 1000); -TWL6030_ADJUSTABLE_LDO(VAUX2_6030, 0x58, 1000); -TWL6030_ADJUSTABLE_LDO(VAUX3_6030, 0x5c, 1000); -TWL6030_ADJUSTABLE_LDO(VMMC, 0x68, 1000); -TWL6030_ADJUSTABLE_LDO(VPP, 0x6c, 1000); -TWL6030_ADJUSTABLE_LDO(VUSIM, 0x74, 1000); +TWL6030_ADJUSTABLE_LDO(VAUX1_6030, 0x54); +TWL6030_ADJUSTABLE_LDO(VAUX2_6030, 0x58); +TWL6030_ADJUSTABLE_LDO(VAUX3_6030, 0x5c); +TWL6030_ADJUSTABLE_LDO(VMMC, 0x68); +TWL6030_ADJUSTABLE_LDO(VPP, 0x6c); +TWL6030_ADJUSTABLE_LDO(VUSIM, 0x74); /* 6025 are renamed compared to 6030 versions */ -TWL6032_ADJUSTABLE_LDO(LDO2, 0x54, 1000); -TWL6032_ADJUSTABLE_LDO(LDO4, 0x58, 1000); -TWL6032_ADJUSTABLE_LDO(LDO3, 0x5c, 1000); -TWL6032_ADJUSTABLE_LDO(LDO5, 0x68, 1000); -TWL6032_ADJUSTABLE_LDO(LDO1, 0x6c, 1000); -TWL6032_ADJUSTABLE_LDO(LDO7, 0x74, 1000); -TWL6032_ADJUSTABLE_LDO(LDO6, 0x60, 1000); -TWL6032_ADJUSTABLE_LDO(LDOLN, 0x64, 1000); -TWL6032_ADJUSTABLE_LDO(LDOUSB, 0x70, 1000); +TWL6032_ADJUSTABLE_LDO(LDO2, 0x54); +TWL6032_ADJUSTABLE_LDO(LDO4, 0x58); +TWL6032_ADJUSTABLE_LDO(LDO3, 0x5c); +TWL6032_ADJUSTABLE_LDO(LDO5, 0x68); +TWL6032_ADJUSTABLE_LDO(LDO1, 0x6c); +TWL6032_ADJUSTABLE_LDO(LDO7, 0x74); +TWL6032_ADJUSTABLE_LDO(LDO6, 0x60); +TWL6032_ADJUSTABLE_LDO(LDOLN, 0x64); +TWL6032_ADJUSTABLE_LDO(LDOUSB, 0x70); TWL6030_FIXED_LDO(VANA, 0x50, 2100, 0); TWL6030_FIXED_LDO(VCXIO, 0x60, 1800, 0); TWL6030_FIXED_LDO(VDAC, 0x64, 1800, 0); @@ -687,14 +668,9 @@ static int twlreg_probe(struct platform_device *pdev) struct regulator_init_data *initdata; struct regulation_constraints *c; struct regulator_dev *rdev; - const struct of_device_id *match; struct regulator_config config = { }; - match = of_match_device(twl_of_match, &pdev->dev); - if (!match) - return -ENODEV; - - template = match->data; + template = of_device_get_match_data(&pdev->dev); if (!template) return -ENODEV; diff --git a/drivers/regulator/uniphier-regulator.c b/drivers/regulator/uniphier-regulator.c index abf22acbd13e..9026d5a3e964 100644 --- a/drivers/regulator/uniphier-regulator.c +++ b/drivers/regulator/uniphier-regulator.c @@ -32,7 +32,7 @@ struct uniphier_regulator_priv { const struct uniphier_regulator_soc_data *data; }; -static struct regulator_ops uniphier_regulator_ops = { +static const struct regulator_ops uniphier_regulator_ops = { .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .is_enabled = regulator_is_enabled_regmap, @@ -87,8 +87,10 @@ static int uniphier_regulator_probe(struct platform_device *pdev) } regmap = devm_regmap_init_mmio(dev, base, priv->data->regconf); - if (IS_ERR(regmap)) - return PTR_ERR(regmap); + if (IS_ERR(regmap)) { + ret = PTR_ERR(regmap); + goto out_rst_assert; + } config.dev = dev; config.driver_data = priv; diff --git a/drivers/regulator/wm831x-dcdc.c b/drivers/regulator/wm831x-dcdc.c index 5a5bc4bb08d2..12b422373580 100644 --- a/drivers/regulator/wm831x-dcdc.c +++ b/drivers/regulator/wm831x-dcdc.c @@ -205,33 +205,10 @@ static irqreturn_t wm831x_dcdc_oc_irq(int irq, void *data) * BUCKV specifics */ -static int wm831x_buckv_list_voltage(struct regulator_dev *rdev, - unsigned selector) -{ - if (selector <= 0x8) - return 600000; - if (selector <= WM831X_BUCKV_MAX_SELECTOR) - return 600000 + ((selector - 0x8) * 12500); - return -EINVAL; -} - -static int wm831x_buckv_map_voltage(struct regulator_dev *rdev, - int min_uV, int max_uV) -{ - u16 vsel; - - if (min_uV < 600000) - vsel = 0; - else if (min_uV <= 1800000) - vsel = DIV_ROUND_UP(min_uV - 600000, 12500) + 8; - else - return -EINVAL; - - if (wm831x_buckv_list_voltage(rdev, vsel) > max_uV) - return -EINVAL; - - return vsel; -} +static const struct regulator_linear_range wm831x_buckv_ranges[] = { + REGULATOR_LINEAR_RANGE(600000, 0, 0x7, 0), + REGULATOR_LINEAR_RANGE(600000, 0x8, 0x68, 12500), +}; static int wm831x_buckv_set_dvs(struct regulator_dev *rdev, int state) { @@ -309,7 +286,7 @@ static int wm831x_buckv_set_suspend_voltage(struct regulator_dev *rdev, u16 reg = dcdc->base + WM831X_DCDC_SLEEP_CONTROL; int vsel; - vsel = wm831x_buckv_map_voltage(rdev, uV, uV); + vsel = regulator_map_voltage_linear_range(rdev, uV, uV); if (vsel < 0) return vsel; @@ -327,52 +304,18 @@ static int wm831x_buckv_get_voltage_sel(struct regulator_dev *rdev) } /* Current limit options */ -static u16 wm831x_dcdc_ilim[] = { - 125, 250, 375, 500, 625, 750, 875, 1000 +static const unsigned int wm831x_dcdc_ilim[] = { + 125000, 250000, 375000, 500000, 625000, 750000, 875000, 1000000 }; -static int wm831x_buckv_set_current_limit(struct regulator_dev *rdev, - int min_uA, int max_uA) -{ - struct wm831x_dcdc *dcdc = rdev_get_drvdata(rdev); - struct wm831x *wm831x = dcdc->wm831x; - u16 reg = dcdc->base + WM831X_DCDC_CONTROL_2; - int i; - - for (i = ARRAY_SIZE(wm831x_dcdc_ilim) - 1; i >= 0; i--) { - if ((min_uA <= wm831x_dcdc_ilim[i]) && - (wm831x_dcdc_ilim[i] <= max_uA)) - return wm831x_set_bits(wm831x, reg, - WM831X_DC1_HC_THR_MASK, - i << WM831X_DC1_HC_THR_SHIFT); - } - - return -EINVAL; -} - -static int wm831x_buckv_get_current_limit(struct regulator_dev *rdev) -{ - struct wm831x_dcdc *dcdc = rdev_get_drvdata(rdev); - struct wm831x *wm831x = dcdc->wm831x; - u16 reg = dcdc->base + WM831X_DCDC_CONTROL_2; - int val; - - val = wm831x_reg_read(wm831x, reg); - if (val < 0) - return val; - - val = (val & WM831X_DC1_HC_THR_MASK) >> WM831X_DC1_HC_THR_SHIFT; - return wm831x_dcdc_ilim[val]; -} - static const struct regulator_ops wm831x_buckv_ops = { .set_voltage_sel = wm831x_buckv_set_voltage_sel, .get_voltage_sel = wm831x_buckv_get_voltage_sel, - .list_voltage = wm831x_buckv_list_voltage, - .map_voltage = wm831x_buckv_map_voltage, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, .set_suspend_voltage = wm831x_buckv_set_suspend_voltage, - .set_current_limit = wm831x_buckv_set_current_limit, - .get_current_limit = wm831x_buckv_get_current_limit, + .set_current_limit = regulator_set_current_limit_regmap, + .get_current_limit = regulator_get_current_limit_regmap, .is_enabled = regulator_is_enabled_regmap, .enable = regulator_enable_regmap, @@ -492,10 +435,16 @@ static int wm831x_buckv_probe(struct platform_device *pdev) dcdc->desc.id = id; dcdc->desc.type = REGULATOR_VOLTAGE; dcdc->desc.n_voltages = WM831X_BUCKV_MAX_SELECTOR + 1; + dcdc->desc.linear_ranges = wm831x_buckv_ranges; + dcdc->desc.n_linear_ranges = ARRAY_SIZE(wm831x_buckv_ranges); dcdc->desc.ops = &wm831x_buckv_ops; dcdc->desc.owner = THIS_MODULE; dcdc->desc.enable_reg = WM831X_DCDC_ENABLE; dcdc->desc.enable_mask = 1 << id; + dcdc->desc.csel_reg = dcdc->base + WM831X_DCDC_CONTROL_2; + dcdc->desc.csel_mask = WM831X_DC1_HC_THR_MASK; + dcdc->desc.n_current_limits = ARRAY_SIZE(wm831x_dcdc_ilim); + dcdc->desc.curr_table = wm831x_dcdc_ilim; ret = wm831x_reg_read(wm831x, dcdc->base + WM831X_DCDC_ON_CONFIG); if (ret < 0) { diff --git a/include/linux/mfd/tps65218.h b/include/linux/mfd/tps65218.h index c204d9a79436..45cdcd0fee53 100644 --- a/include/linux/mfd/tps65218.h +++ b/include/linux/mfd/tps65218.h @@ -208,6 +208,7 @@ enum tps65218_regulator_id { /* LDOs */ TPS65218_LDO_1, /* LS's */ + TPS65218_LS_2, TPS65218_LS_3, }; @@ -218,7 +219,7 @@ enum tps65218_regulator_id { /* Number of LDO voltage regulators available */ #define TPS65218_NUM_LDO 1 /* Number of total LS current regulators available */ -#define TPS65218_NUM_LS 1 +#define TPS65218_NUM_LS 2 /* Number of total regulators available */ #define TPS65218_NUM_REGULATOR (TPS65218_NUM_DCDC + TPS65218_NUM_LDO \ + TPS65218_NUM_LS) diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h index 389bcaf7900f..377da2357118 100644 --- a/include/linux/regulator/driver.h +++ b/include/linux/regulator/driver.h @@ -264,6 +264,7 @@ enum regulator_type { * @continuous_voltage_range: Indicates if the regulator can set any * voltage within constrains range. * @n_voltages: Number of selectors available for ops.list_voltage(). + * @n_current_limits: Number of selectors available for current limits * * @min_uV: Voltage given by the lowest selector (if linear mapping) * @uV_step: Voltage increase with each selector (if linear mapping) @@ -278,14 +279,15 @@ enum regulator_type { * @n_linear_ranges: Number of entries in the @linear_ranges (and in * linear_range_selectors if used) table(s). * @volt_table: Voltage mapping table (if table based mapping) + * @curr_table: Current limit mapping table (if table based mapping) * * @vsel_range_reg: Register for range selector when using pickable ranges * and regulator_regmap_X_voltage_X_pickable functions. * @vsel_range_mask: Mask for register bitfield used for range selector * @vsel_reg: Register for selector when using regulator_regmap_X_voltage_ * @vsel_mask: Mask for register bitfield used for selector - * @csel_reg: Register for TPS65218 LS3 current regulator - * @csel_mask: Mask for TPS65218 LS3 current regulator + * @csel_reg: Register for current limit selector using regmap set_current_limit + * @csel_mask: Mask for register bitfield used for current limit selector * @apply_reg: Register for initiate voltage change on the output when * using regulator_set_voltage_sel_regmap * @apply_bit: Register bitfield used for initiate voltage change on the @@ -333,6 +335,7 @@ struct regulator_desc { int id; unsigned int continuous_voltage_range:1; unsigned n_voltages; + unsigned int n_current_limits; const struct regulator_ops *ops; int irq; enum regulator_type type; @@ -351,6 +354,7 @@ struct regulator_desc { int n_linear_ranges; const unsigned int *volt_table; + const unsigned int *curr_table; unsigned int vsel_range_reg; unsigned int vsel_range_mask; @@ -401,13 +405,7 @@ struct regulator_desc { * NULL). * @regmap: regmap to use for core regmap helpers if dev_get_regmap() is * insufficient. - * @ena_gpio_initialized: GPIO controlling regulator enable was properly - * initialized, meaning that >= 0 is a valid gpio - * identifier and < 0 is a non existent gpio. - * @ena_gpio: GPIO controlling regulator enable. - * @ena_gpiod: GPIO descriptor controlling regulator enable. - * @ena_gpio_invert: Sense for GPIO enable control. - * @ena_gpio_flags: Flags to use when calling gpio_request_one() + * @ena_gpiod: GPIO controlling regulator enable. */ struct regulator_config { struct device *dev; @@ -416,11 +414,7 @@ struct regulator_config { struct device_node *of_node; struct regmap *regmap; - bool ena_gpio_initialized; - int ena_gpio; struct gpio_desc *ena_gpiod; - unsigned int ena_gpio_invert:1; - unsigned int ena_gpio_flags; }; /* @@ -503,6 +497,7 @@ int regulator_notifier_call_chain(struct regulator_dev *rdev, void *rdev_get_drvdata(struct regulator_dev *rdev); struct device *rdev_get_dev(struct regulator_dev *rdev); +struct regmap *rdev_get_regmap(struct regulator_dev *rdev); int rdev_get_id(struct regulator_dev *rdev); int regulator_mode_to_status(unsigned int); @@ -543,9 +538,18 @@ int regulator_set_pull_down_regmap(struct regulator_dev *rdev); int regulator_set_active_discharge_regmap(struct regulator_dev *rdev, bool enable); +int regulator_set_current_limit_regmap(struct regulator_dev *rdev, + int min_uA, int max_uA); +int regulator_get_current_limit_regmap(struct regulator_dev *rdev); void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data); void regulator_lock(struct regulator_dev *rdev); void regulator_unlock(struct regulator_dev *rdev); +/* + * Helper functions intended to be used by regulator drivers prior registering + * their regulators. + */ +int regulator_desc_list_voltage_linear_range(const struct regulator_desc *desc, + unsigned int selector); #endif diff --git a/include/linux/regulator/fixed.h b/include/linux/regulator/fixed.h index 1a4340ed8e2b..f10140da7145 100644 --- a/include/linux/regulator/fixed.h +++ b/include/linux/regulator/fixed.h @@ -25,14 +25,6 @@ struct regulator_init_data; * @input_supply: Name of the input regulator supply * @microvolts: Output voltage of regulator * @startup_delay: Start-up time in microseconds - * @gpio_is_open_drain: Gpio pin is open drain or normal type. - * If it is open drain type then HIGH will be set - * through PULL-UP with setting gpio as input - * and low will be set as gpio-output with driven - * to low. For non-open-drain case, the gpio will - * will be in output and drive to low/high accordingly. - * @enable_high: Polarity of enable GPIO - * 1 = Active high, 0 = Active low * @enabled_at_boot: Whether regulator has been enabled at * boot or not. 1 = Yes, 0 = No * This is used to keep the regulator at @@ -48,8 +40,6 @@ struct fixed_voltage_config { const char *input_supply; int microvolts; unsigned startup_delay; - unsigned gpio_is_open_drain:1; - unsigned enable_high:1; unsigned enabled_at_boot:1; struct regulator_init_data *init_data; }; diff --git a/include/linux/regulator/gpio-regulator.h b/include/linux/regulator/gpio-regulator.h index 19fbd267406d..11cd6375215d 100644 --- a/include/linux/regulator/gpio-regulator.h +++ b/include/linux/regulator/gpio-regulator.h @@ -21,6 +21,8 @@ #ifndef __REGULATOR_GPIO_H #define __REGULATOR_GPIO_H +#include <linux/gpio/consumer.h> + struct regulator_init_data; enum regulator_type; @@ -44,18 +46,14 @@ struct gpio_regulator_state { /** * struct gpio_regulator_config - config structure * @supply_name: Name of the regulator supply - * @enable_gpio: GPIO to use for enable control - * set to -EINVAL if not used - * @enable_high: Polarity of enable GPIO - * 1 = Active high, 0 = Active low * @enabled_at_boot: Whether regulator has been enabled at * boot or not. 1 = Yes, 0 = No * This is used to keep the regulator at * the default state * @startup_delay: Start-up time in microseconds - * @gpios: Array containing the gpios needed to control - * the setting of the regulator - * @nr_gpios: Number of gpios + * @gflags: Array of GPIO configuration flags for initial + * states + * @ngpios: Number of GPIOs and configurations available * @states: Array of gpio_regulator_state entries describing * the gpio state for specific voltages * @nr_states: Number of states available @@ -69,13 +67,11 @@ struct gpio_regulator_state { struct gpio_regulator_config { const char *supply_name; - int enable_gpio; - unsigned enable_high:1; unsigned enabled_at_boot:1; unsigned startup_delay; - struct gpio *gpios; - int nr_gpios; + enum gpiod_flags *gflags; + int ngpios; struct gpio_regulator_state *states; int nr_states; |