diff options
| -rw-r--r-- | drivers/regulator/core.c | 11 | ||||
| -rw-r--r-- | drivers/regulator/of_regulator.c | 6 | ||||
| -rw-r--r-- | include/linux/regulator/driver.h | 3 | ||||
| -rw-r--r-- | include/linux/regulator/machine.h | 12 |
4 files changed, 32 insertions, 0 deletions
diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c index 744c9889f88d..7ebb7c899158 100644 --- a/drivers/regulator/core.c +++ b/drivers/regulator/core.c @@ -1140,6 +1140,17 @@ static int set_machine_constraints(struct regulator_dev *rdev, } } + if (rdev->constraints->active_discharge && ops->set_active_discharge) { + bool ad_state = (rdev->constraints->active_discharge == + REGULATOR_ACTIVE_DISCHARGE_ENABLE) ? true : false; + + ret = ops->set_active_discharge(rdev, ad_state); + if (ret < 0) { + rdev_err(rdev, "failed to set active discharge\n"); + return ret; + } + } + print_constraints(rdev); return 0; out: diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c index 499e437c7e91..fe2e33441dae 100644 --- a/drivers/regulator/of_regulator.c +++ b/drivers/regulator/of_regulator.c @@ -93,6 +93,12 @@ static void of_get_regulation_constraints(struct device_node *np, constraints->soft_start = of_property_read_bool(np, "regulator-soft-start"); + ret = of_property_read_u32(np, "regulator-active-discharge", &pval); + if (!ret) { + constraints->active_discharge = + (pval) ? REGULATOR_ACTIVE_DISCHARGE_ENABLE : + REGULATOR_ACTIVE_DISCHARGE_DISABLE; + } if (!of_property_read_u32(np, "regulator-initial-mode", &pval)) { if (desc && desc->of_map_mode) { diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h index 16ac9e108806..59dbaf78a25c 100644 --- a/include/linux/regulator/driver.h +++ b/include/linux/regulator/driver.h @@ -93,6 +93,8 @@ struct regulator_linear_range { * @get_current_limit: Get the configured limit for a current-limited regulator. * @set_input_current_limit: Configure an input limit. * + * @set_active_discharge: Set active discharge enable/disable of regulators. + * * @set_mode: Set the configured operating mode for the regulator. * @get_mode: Get the configured operating mode for the regulator. * @get_status: Return actual (not as-configured) status of regulator, as a @@ -149,6 +151,7 @@ struct regulator_ops { int (*set_input_current_limit) (struct regulator_dev *, int lim_uA); int (*set_over_current_protection) (struct regulator_dev *); + int (*set_active_discharge) (struct regulator_dev *, bool enable); /* enable/disable regulator */ int (*enable) (struct regulator_dev *); diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h index a1067d0b3991..5d627c83a630 100644 --- a/include/linux/regulator/machine.h +++ b/include/linux/regulator/machine.h @@ -42,6 +42,13 @@ struct regulator; #define REGULATOR_CHANGE_DRMS 0x10 #define REGULATOR_CHANGE_BYPASS 0x20 +/* Regulator active discharge flags */ +enum regulator_active_discharge { + REGULATOR_ACTIVE_DISCHARGE_DEFAULT, + REGULATOR_ACTIVE_DISCHARGE_DISABLE, + REGULATOR_ACTIVE_DISCHARGE_ENABLE, +}; + /** * struct regulator_state - regulator state during low power system states * @@ -100,6 +107,9 @@ struct regulator_state { * @initial_state: Suspend state to set by default. * @initial_mode: Mode to set at startup. * @ramp_delay: Time to settle down after voltage change (unit: uV/us) + * @active_discharge: Enable/disable active discharge. The enum + * regulator_active_discharge values are used for + * initialisation. * @enable_time: Turn-on time of the rails (unit: microseconds) */ struct regulation_constraints { @@ -140,6 +150,8 @@ struct regulation_constraints { unsigned int ramp_delay; unsigned int enable_time; + unsigned int active_discharge; + /* constraint flags */ unsigned always_on:1; /* regulator never off when system is on */ unsigned boot_on:1; /* bootloader/firmware enabled regulator */ |