diff options
| -rw-r--r-- | drivers/net/e1000/e1000_hw.c | 2 | ||||
| -rw-r--r-- | drivers/net/e1000/e1000_hw.h | 3 | ||||
| -rw-r--r-- | drivers/net/e1000/e1000_main.c | 58 |
3 files changed, 33 insertions, 30 deletions
diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c index e1a3fc1303ee..1e5ae112d57a 100644 --- a/drivers/net/e1000/e1000_hw.c +++ b/drivers/net/e1000/e1000_hw.c @@ -1955,7 +1955,7 @@ static s32 e1000_setup_copper_link(struct e1000_hw *hw) s32 ret_val; u16 i; u16 phy_data; - u16 reg_data; + u16 reg_data = 0; DEBUGFUNC("e1000_setup_copper_link"); diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h index 99fce2c5dd26..a8866bdbb671 100644 --- a/drivers/net/e1000/e1000_hw.h +++ b/drivers/net/e1000/e1000_hw.h @@ -523,11 +523,8 @@ s32 e1000_check_phy_reset_block(struct e1000_hw *hw); /* The sizes (in bytes) of a ethernet packet */ #define ENET_HEADER_SIZE 14 -#define MAXIMUM_ETHERNET_FRAME_SIZE 1518 /* With FCS */ #define MINIMUM_ETHERNET_FRAME_SIZE 64 /* With FCS */ #define ETHERNET_FCS_SIZE 4 -#define MAXIMUM_ETHERNET_PACKET_SIZE \ - (MAXIMUM_ETHERNET_FRAME_SIZE - ETHERNET_FCS_SIZE) #define MINIMUM_ETHERNET_PACKET_SIZE \ (MINIMUM_ETHERNET_FRAME_SIZE - ETHERNET_FCS_SIZE) #define CRC_LENGTH ETHERNET_FCS_SIZE diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index f2db9e2069e7..d7df00c2dbd6 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -641,8 +641,8 @@ void e1000_reset(struct e1000_adapter *adapter) { struct e1000_hw *hw = &adapter->hw; u32 pba = 0, tx_space, min_tx_space, min_rx_space; - u16 fc_high_water_mark = E1000_FC_HIGH_DIFF; bool legacy_pba_adjust = false; + u16 hwm; /* Repartition Pba for greater than 9k mtu * To take effect CTRL.RST is required. @@ -686,7 +686,7 @@ void e1000_reset(struct e1000_adapter *adapter) } if (legacy_pba_adjust) { - if (adapter->netdev->mtu > E1000_RXBUFFER_8192) + if (hw->max_frame_size > E1000_RXBUFFER_8192) pba -= 8; /* allocate more FIFO for Tx */ if (hw->mac_type == e1000_82547) { @@ -696,14 +696,14 @@ void e1000_reset(struct e1000_adapter *adapter) (E1000_PBA_40K - pba) << E1000_PBA_BYTES_SHIFT; atomic_set(&adapter->tx_fifo_stall, 0); } - } else if (hw->max_frame_size > MAXIMUM_ETHERNET_FRAME_SIZE) { + } else if (hw->max_frame_size > ETH_FRAME_LEN + ETH_FCS_LEN) { /* adjust PBA for jumbo frames */ ew32(PBA, pba); /* To maintain wire speed transmits, the Tx FIFO should be - * large enough to accomodate two full transmit packets, + * large enough to accommodate two full transmit packets, * rounded up to the next 1KB and expressed in KB. Likewise, - * the Rx FIFO should be large enough to accomodate at least + * the Rx FIFO should be large enough to accommodate at least * one full receive packet and is similarly rounded up and * expressed in KB. */ pba = er32(PBA); @@ -711,13 +711,17 @@ void e1000_reset(struct e1000_adapter *adapter) tx_space = pba >> 16; /* lower 16 bits has Rx packet buffer allocation size in KB */ pba &= 0xffff; - /* don't include ethernet FCS because hardware appends/strips */ - min_rx_space = adapter->netdev->mtu + ENET_HEADER_SIZE + - VLAN_TAG_SIZE; - min_tx_space = min_rx_space; - min_tx_space *= 2; + /* + * the tx fifo also stores 16 bytes of information about the tx + * but don't include ethernet FCS because hardware appends it + */ + min_tx_space = (hw->max_frame_size + + sizeof(struct e1000_tx_desc) - + ETH_FCS_LEN) * 2; min_tx_space = ALIGN(min_tx_space, 1024); min_tx_space >>= 10; + /* software strips receive CRC, so leave room for it */ + min_rx_space = hw->max_frame_size; min_rx_space = ALIGN(min_rx_space, 1024); min_rx_space >>= 10; @@ -754,19 +758,21 @@ void e1000_reset(struct e1000_adapter *adapter) ew32(PBA, pba); - /* flow control settings */ - /* Set the FC high water mark to 90% of the FIFO size. - * Required to clear last 3 LSB */ - fc_high_water_mark = ((pba * 9216)/10) & 0xFFF8; - /* We can't use 90% on small FIFOs because the remainder - * would be less than 1 full frame. In this case, we size - * it to allow at least a full frame above the high water - * mark. */ - if (pba < E1000_PBA_16K) - fc_high_water_mark = (pba * 1024) - 1600; - - hw->fc_high_water = fc_high_water_mark; - hw->fc_low_water = fc_high_water_mark - 8; + /* + * flow control settings: + * The high water mark must be low enough to fit one full frame + * (or the size used for early receive) above it in the Rx FIFO. + * Set it to the lower of: + * - 90% of the Rx FIFO size, and + * - the full Rx FIFO size minus the early receive size (for parts + * with ERT support assuming ERT set to E1000_ERT_2048), or + * - the full Rx FIFO size minus one full frame + */ + hwm = min(((pba << 10) * 9 / 10), + ((pba << 10) - hw->max_frame_size)); + + hw->fc_high_water = hwm & 0xFFF8; /* 8-byte granularity */ + hw->fc_low_water = hw->fc_high_water - 8; hw->fc_pause_time = E1000_FC_PAUSE_TIME; hw->fc_send_xon = 1; hw->fc = hw->original_fc; @@ -3474,7 +3480,7 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu) switch (hw->mac_type) { case e1000_undefined ... e1000_82542_rev2_1: case e1000_ich8lan: - if (max_frame > MAXIMUM_ETHERNET_FRAME_SIZE) { + if (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)) { DPRINTK(PROBE, ERR, "Jumbo Frames not supported.\n"); return -EINVAL; } @@ -3487,7 +3493,7 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu) &eeprom_data); if ((hw->device_id != E1000_DEV_ID_82573L) || (eeprom_data & EEPROM_WORD1A_ASPM_MASK)) { - if (max_frame > MAXIMUM_ETHERNET_FRAME_SIZE) { + if (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)) { DPRINTK(PROBE, ERR, "Jumbo Frames not supported.\n"); return -EINVAL; @@ -3535,7 +3541,7 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu) /* adjust allocation if LPE protects us, and we aren't using SBP */ if (!hw->tbi_compatibility_on && - ((max_frame == MAXIMUM_ETHERNET_FRAME_SIZE) || + ((max_frame == (ETH_FRAME_LEN + ETH_FCS_LEN)) || (max_frame == MAXIMUM_ETHERNET_VLAN_SIZE))) adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE; |