diff options
| -rw-r--r-- | Documentation/ide/ide.txt | 2 | ||||
| -rw-r--r-- | Documentation/kernel-parameters.txt | 2 | ||||
| -rw-r--r-- | drivers/ide/Kconfig | 9 | ||||
| -rw-r--r-- | drivers/ide/ide-scan-pci.c | 9 | ||||
| -rw-r--r-- | drivers/ide/ide.c | 12 | ||||
| -rw-r--r-- | include/linux/ide.h | 1 |
6 files changed, 4 insertions, 31 deletions
diff --git a/Documentation/ide/ide.txt b/Documentation/ide/ide.txt index 818676aad45a..ce7c01af30f6 100644 --- a/Documentation/ide/ide.txt +++ b/Documentation/ide/ide.txt @@ -269,8 +269,6 @@ Summary of ide driver parameters for kernel command line ability to bit test for detection is currently unknown. - "ide=reverse" : formerly called to pci sub-system, but now local. - "ide=doubler" : probe/support IDE doublers on Amiga There may be more options than shown -- use the source, Luke! diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index dafd001bf833..228d85a3f319 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -763,7 +763,7 @@ and is between 256 and 4096 characters. It is defined in the file Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]] ide= [HW] (E)IDE subsystem - Format: ide=nodma or ide=doubler or ide=reverse + Format: ide=nodma or ide=doubler See Documentation/ide/ide.txt. ide?= [HW] (E)IDE subsystem diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig index eed6d8e1b5c7..ac5875783430 100644 --- a/drivers/ide/Kconfig +++ b/drivers/ide/Kconfig @@ -416,12 +416,6 @@ config BLK_DEV_OFFBOARD This can improve the usability of some boot managers such as lilo when booting from a drive on an off-board controller. - If you say Y here, and you actually want to reverse the device scan - order as explained above, you also need to issue the kernel command - line option "ide=reverse". (Try "man bootparam" or see the - documentation of your boot loader (lilo or loadlin) about how to - pass options to the kernel at boot time.) - Note that, if you do this, the order of the hd* devices will be rearranged which may require modification of fstab and other files. @@ -615,8 +609,7 @@ config BLK_DEV_HPT366 reference to device 0x80. The other solution is to say Y to "Boot off-board chipsets first support" (CONFIG_BLK_DEV_OFFBOARD) unless your mother board has the chipset natively mounted. Regardless one - should use the fore mentioned option and call at LILO or include - "ide=reverse" in LILO's append-line. + should use the fore mentioned option and call at LILO. This driver requires dynamic tuning of the chipset during the ide-probe at boot. It is reported to support DVD II drives, by the diff --git a/drivers/ide/ide-scan-pci.c b/drivers/ide/ide-scan-pci.c index 93d2e41be853..98888da1b600 100644 --- a/drivers/ide/ide-scan-pci.c +++ b/drivers/ide/ide-scan-pci.c @@ -88,13 +88,8 @@ static int __init ide_scan_pcibus(void) struct list_head *l, *n; pre_init = 0; - if (!ide_scan_direction) - while ((dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev))) - ide_scan_pcidev(dev); - else - while ((dev = pci_get_device_reverse(PCI_ANY_ID, PCI_ANY_ID, - dev))) - ide_scan_pcidev(dev); + while ((dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev))) + ide_scan_pcidev(dev); /* * Hand the drivers over to the PCI layer now we diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c index fc69fe2e3ec0..5f545153391a 100644 --- a/drivers/ide/ide.c +++ b/drivers/ide/ide.c @@ -90,10 +90,6 @@ static int system_bus_speed; /* holds what we think is VESA/PCI bus speed */ DEFINE_MUTEX(ide_cfg_mtx); __cacheline_aligned_in_smp DEFINE_SPINLOCK(ide_lock); -#ifdef CONFIG_IDEPCI_PCIBUS_ORDER -int ide_scan_direction; /* THIS was formerly 2.2.x pci=reverse */ -#endif - int noautodma = 0; #ifdef CONFIG_BLK_DEV_IDEACPI @@ -1217,14 +1213,6 @@ static int __init ide_setup(char *s) goto obsolete_option; } -#ifdef CONFIG_IDEPCI_PCIBUS_ORDER - if (!strcmp(s, "ide=reverse")) { - ide_scan_direction = 1; - printk(" : Enabled support for IDE inverse scan order.\n"); - goto obsolete_option; - } -#endif - #ifdef CONFIG_BLK_DEV_IDEACPI if (!strcmp(s, "ide=noacpi")) { //printk(" : Disable IDE ACPI support.\n"); diff --git a/include/linux/ide.h b/include/linux/ide.h index bc26b2f27359..43d2968a4e13 100644 --- a/include/linux/ide.h +++ b/include/linux/ide.h @@ -990,7 +990,6 @@ extern void do_ide_request(struct request_queue *); void ide_init_disk(struct gendisk *, ide_drive_t *); #ifdef CONFIG_IDEPCI_PCIBUS_ORDER -extern int ide_scan_direction; extern int __ide_pci_register_driver(struct pci_driver *driver, struct module *owner, const char *mod_name); #define ide_pci_register_driver(d) __ide_pci_register_driver(d, THIS_MODULE, KBUILD_MODNAME) #else |