diff options
| -rw-r--r-- | Documentation/leds/00-INDEX | 2 | ||||
| -rw-r--r-- | Documentation/leds/leds-lp5562.txt | 135 | ||||
| -rw-r--r-- | Documentation/leds/leds-lp55xx.txt | 46 | ||||
| -rw-r--r-- | drivers/leds/Kconfig | 14 | ||||
| -rw-r--r-- | drivers/leds/Makefile | 1 | ||||
| -rw-r--r-- | drivers/leds/leds-lp5562.c | 593 | ||||
| -rw-r--r-- | drivers/leds/leds-lp55xx-common.c | 2 | ||||
| -rw-r--r-- | include/linux/platform_data/leds-lp55xx.h | 13 |
8 files changed, 799 insertions, 7 deletions
diff --git a/Documentation/leds/00-INDEX b/Documentation/leds/00-INDEX index 5246090ef15c..1ecd1596633e 100644 --- a/Documentation/leds/00-INDEX +++ b/Documentation/leds/00-INDEX @@ -6,6 +6,8 @@ leds-lp5521.txt - notes on how to use the leds-lp5521 driver. leds-lp5523.txt - notes on how to use the leds-lp5523 driver. +leds-lp5562.txt + - notes on how to use the leds-lp5562 driver. leds-lp55xx.txt - description about lp55xx common driver. leds-lm3556.txt diff --git a/Documentation/leds/leds-lp5562.txt b/Documentation/leds/leds-lp5562.txt new file mode 100644 index 000000000000..96061000dd93 --- /dev/null +++ b/Documentation/leds/leds-lp5562.txt @@ -0,0 +1,135 @@ +Kernel driver for LP5562 +======================== + +* TI LP5562 LED Driver + +Author: Milo(Woogyom) Kim <milo.kim@ti.com> + +Description + + LP5562 can drive up to 4 channels. R/G/B and White. + LEDs can be controlled directly via the led class control interface. + + All four channels can be also controlled using the engine micro programs. + LP5562 has the internal program memory for running various LED patterns. + For the details, please refer to 'firmware' section in leds-lp55xx.txt + +Device attribute: engine_mux + + 3 Engines are allocated in LP5562, but the number of channel is 4. + Therefore each channel should be mapped to the engine number. + Value : RGB or W + + This attribute is used for programming LED data with the firmware interface. + Unlike the LP5521/LP5523/55231, LP5562 has unique feature for the engine mux, + so additional sysfs is required. + + LED Map + Red ... Engine 1 (fixed) + Green ... Engine 2 (fixed) + Blue ... Engine 3 (fixed) + White ... Engine 1 or 2 or 3 (selective) + +How to load the program data using engine_mux + + Before loading the LP5562 program data, engine_mux should be written between + the engine selection and loading the firmware. + Engine mux has two different mode, RGB and W. + RGB is used for loading RGB program data, W is used for W program data. + + For example, run blinking green channel pattern, + echo 2 > /sys/bus/i2c/devices/xxxx/select_engine # 2 is for green channel + echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux # engine mux for RGB + echo 1 > /sys/class/firmware/lp5562/loading + echo "4000600040FF6000" > /sys/class/firmware/lp5562/data + echo 0 > /sys/class/firmware/lp5562/loading + echo 1 > /sys/bus/i2c/devices/xxxx/run_engine + + To run a blinking white pattern, + echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine + echo "W" > /sys/bus/i2c/devices/xxxx/engine_mux + echo 1 > /sys/class/firmware/lp5562/loading + echo "4000600040FF6000" > /sys/class/firmware/lp5562/data + echo 0 > /sys/class/firmware/lp5562/loading + echo 1 > /sys/bus/i2c/devices/xxxx/run_engine + +How to load the predefined patterns + + Please refer to 'leds-lp55xx.txt" + +Setting Current of Each Channel + + Like LP5521 and LP5523/55231, LP5562 provides LED current settings. + The 'led_current' and 'max_current' are used. + +(Example of Platform data) + +To configure the platform specific data, lp55xx_platform_data structure is used. + +static struct lp55xx_led_config lp5562_led_config[] = { + { + .name = "R", + .chan_nr = 0, + .led_current = 20, + .max_current = 40, + }, + { + .name = "G", + .chan_nr = 1, + .led_current = 20, + .max_current = 40, + }, + { + .name = "B", + .chan_nr = 2, + .led_current = 20, + .max_current = 40, + }, + { + .name = "W", + .chan_nr = 3, + .led_current = 20, + .max_current = 40, + }, +}; + +static int lp5562_setup(void) +{ + /* setup HW resources */ +} + +static void lp5562_release(void) +{ + /* Release HW resources */ +} + +static void lp5562_enable(bool state) +{ + /* Control of chip enable signal */ +} + +static struct lp55xx_platform_data lp5562_platform_data = { + .led_config = lp5562_led_config, + .num_channels = ARRAY_SIZE(lp5562_led_config), + .setup_resources = lp5562_setup, + .release_resources = lp5562_release, + .enable = lp5562_enable, +}; + +If the current is set to 0 in the platform data, that channel is +disabled and it is not visible in the sysfs. + +The 'update_config' : CONFIG register (ADDR 08h) +This value is platform-specific data. +If update_config is not defined, the CONFIG register is set with +'LP5562_PWRSAVE_EN | LP5562_CLK_AUTO'. +(Enable auto-powersave, set automatic clock source selection) + +#define LP5562_CONFIGS (LP5562_PWM_HF | LP5562_PWRSAVE_EN | \ + LP5562_CLK_SRC_EXT) + +static struct lp55xx_platform_data lp5562_pdata = { + .led_config = lp5562_led_config, + .num_channels = ARRAY_SIZE(lp5562_led_config), + .update_config = LP5562_CONFIGS, +}; diff --git a/Documentation/leds/leds-lp55xx.txt b/Documentation/leds/leds-lp55xx.txt index ced41868d2d1..eec8fa2ffe4e 100644 --- a/Documentation/leds/leds-lp55xx.txt +++ b/Documentation/leds/leds-lp55xx.txt @@ -5,7 +5,7 @@ Authors: Milo(Woogyom) Kim <milo.kim@ti.com> Description ----------- -LP5521, LP5523/55231 have common features as below. +LP5521, LP5523/55231 and LP5562 have common features as below. Register access via the I2C Device initialization/deinitialization @@ -116,3 +116,47 @@ To support this, 'run_engine' and 'firmware_cb' are configurable in each driver. run_engine : Control the selected engine firmware_cb : The callback function after loading the firmware is done. Chip specific commands for loading and updating program memory. + +( Predefined pattern data ) + +Without the firmware interface, LP55xx driver provides another method for +loading a LED pattern. That is 'predefined' pattern. +A predefined pattern is defined in the platform data and load it(or them) +via the sysfs if needed. +To use the predefined pattern concept, 'patterns' and 'num_patterns' should be +configured. + + Example of predefined pattern data: + + /* mode_1: blinking data */ + static const u8 mode_1[] = { + 0x40, 0x00, 0x60, 0x00, 0x40, 0xFF, 0x60, 0x00, + }; + + /* mode_2: always on */ + static const u8 mode_2[] = { 0x40, 0xFF, }; + + struct lp55xx_predef_pattern board_led_patterns[] = { + { + .r = mode_1, + .size_r = ARRAY_SIZE(mode_1), + }, + { + .b = mode_2, + .size_b = ARRAY_SIZE(mode_2), + }, + } + + struct lp55xx_platform_data lp5562_pdata = { + ... + .patterns = board_led_patterns, + .num_patterns = ARRAY_SIZE(board_led_patterns), + }; + +Then, mode_1 and mode_2 can be run via through the sysfs. + + echo 1 > /sys/bus/i2c/devices/xxxx/led_pattern # red blinking LED pattern + echo 2 > /sys/bus/i2c/devices/xxxx/led_pattern # blue LED always on + +To stop running pattern, + echo 0 > /sys/bus/i2c/devices/xxxx/led_pattern diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig index ec50824c02ec..c7f755034375 100644 --- a/drivers/leds/Kconfig +++ b/drivers/leds/Kconfig @@ -194,8 +194,8 @@ config LEDS_LP3944 module will be called leds-lp3944. config LEDS_LP55XX_COMMON - tristate "Common Driver for TI/National LP5521 and LP5523/55231" - depends on LEDS_LP5521 || LEDS_LP5523 + tristate "Common Driver for TI/National LP5521, LP5523/55231 and LP5562" + depends on LEDS_LP5521 || LEDS_LP5523 || LEDS_LP5562 select FW_LOADER help This option supports common operations for LP5521 and LP5523/55231 @@ -222,6 +222,16 @@ config LEDS_LP5523 Driver provides direct control via LED class and interface for programming the engines. +config LEDS_LP5562 + tristate "LED Support for TI LP5562 LED driver chip" + depends on LEDS_CLASS && I2C + select LEDS_LP55XX_COMMON + help + If you say yes here you get support for TI LP5562 LED driver. + It is 4 channels chip with programmable engines. + Driver provides direct control via LED class and interface for + programming the engines. + config LEDS_LP8788 tristate "LED support for the TI LP8788 PMIC" depends on LEDS_CLASS diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile index 215e7e3b6173..ab8f5c549ad3 100644 --- a/drivers/leds/Makefile +++ b/drivers/leds/Makefile @@ -26,6 +26,7 @@ obj-$(CONFIG_LEDS_LP3944) += leds-lp3944.o obj-$(CONFIG_LEDS_LP55XX_COMMON) += leds-lp55xx-common.o obj-$(CONFIG_LEDS_LP5521) += leds-lp5521.o obj-$(CONFIG_LEDS_LP5523) += leds-lp5523.o +obj-$(CONFIG_LEDS_LP5562) += leds-lp5562.o obj-$(CONFIG_LEDS_LP8788) += leds-lp8788.o obj-$(CONFIG_LEDS_TCA6507) += leds-tca6507.o obj-$(CONFIG_LEDS_CLEVO_MAIL) += leds-clevo-mail.o diff --git a/drivers/leds/leds-lp5562.c b/drivers/leds/leds-lp5562.c new file mode 100644 index 000000000000..f8b927788c3a --- /dev/null +++ b/drivers/leds/leds-lp5562.c @@ -0,0 +1,593 @@ +/* + * LP5562 LED driver + * + * Copyright (C) 2013 Texas Instruments + * + * Author: Milo(Woogyom) Kim <milo.kim@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/delay.h> +#include <linux/firmware.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/leds.h> +#include <linux/module.h> +#include <linux/mutex.h> +#include <linux/platform_data/leds-lp55xx.h> +#include <linux/slab.h> + +#include "leds-lp55xx-common.h" + +#define LP5562_PROGRAM_LENGTH 32 +#define LP5562_MAX_LEDS 4 + +/* ENABLE Register 00h */ +#define LP5562_REG_ENABLE 0x00 +#define LP5562_EXEC_ENG1_M 0x30 +#define LP5562_EXEC_ENG2_M 0x0C +#define LP5562_EXEC_ENG3_M 0x03 +#define LP5562_EXEC_M 0x3F +#define LP5562_MASTER_ENABLE 0x40 /* Chip master enable */ +#define LP5562_LOGARITHMIC_PWM 0x80 /* Logarithmic PWM adjustment */ +#define LP5562_EXEC_RUN 0x2A +#define LP5562_ENABLE_DEFAULT \ + (LP5562_MASTER_ENABLE | LP5562_LOGARITHMIC_PWM) +#define LP5562_ENABLE_RUN_PROGRAM \ + (LP5562_ENABLE_DEFAULT | LP5562_EXEC_RUN) + +/* OPMODE Register 01h */ +#define LP5562_REG_OP_MODE 0x01 +#define LP5562_MODE_ENG1_M 0x30 +#define LP5562_MODE_ENG2_M 0x0C +#define LP5562_MODE_ENG3_M 0x03 +#define LP5562_LOAD_ENG1 0x10 +#define LP5562_LOAD_ENG2 0x04 +#define LP5562_LOAD_ENG3 0x01 +#define LP5562_RUN_ENG1 0x20 +#define LP5562_RUN_ENG2 0x08 +#define LP5562_RUN_ENG3 0x02 +#define LP5562_ENG1_IS_LOADING(mode) \ + ((mode & LP5562_MODE_ENG1_M) == LP5562_LOAD_ENG1) +#define LP5562_ENG2_IS_LOADING(mode) \ + ((mode & LP5562_MODE_ENG2_M) == LP5562_LOAD_ENG2) +#define LP5562_ENG3_IS_LOADING(mode) \ + ((mode & LP5562_MODE_ENG3_M) == LP5562_LOAD_ENG3) + +/* BRIGHTNESS Registers */ +#define LP5562_REG_R_PWM 0x04 +#define LP5562_REG_G_PWM 0x03 +#define LP5562_REG_B_PWM 0x02 +#define LP5562_REG_W_PWM 0x0E + +/* CURRENT Registers */ +#define LP5562_REG_R_CURRENT 0x07 +#define LP5562_REG_G_CURRENT 0x06 +#define LP5562_REG_B_CURRENT 0x05 +#define LP5562_REG_W_CURRENT 0x0F + +/* CONFIG Register 08h */ +#define LP5562_REG_CONFIG 0x08 +#define LP5562_DEFAULT_CFG \ + (LP5562_PWM_HF | LP5562_PWRSAVE_EN | LP5562_CLK_INT) + +/* RESET Register 0Dh */ +#define LP5562_REG_RESET 0x0D +#define LP5562_RESET 0xFF + +/* PROGRAM ENGINE Registers */ +#define LP5562_REG_PROG_MEM_ENG1 0x10 +#define LP5562_REG_PROG_MEM_ENG2 0x30 +#define LP5562_REG_PROG_MEM_ENG3 0x50 + +/* LEDMAP Register 70h */ +#define LP5562_REG_ENG_SEL 0x70 +#define LP5562_ENG_SEL_PWM 0 +#define LP5562_ENG_FOR_RGB_M 0x3F +#define LP5562_ENG_SEL_RGB 0x1B /* R:ENG1, G:ENG2, B:ENG3 */ +#define LP5562_ENG_FOR_W_M 0xC0 +#define LP5562_ENG1_FOR_W 0x40 /* W:ENG1 */ +#define LP5562_ENG2_FOR_W 0x80 /* W:ENG2 */ +#define LP5562_ENG3_FOR_W 0xC0 /* W:ENG3 */ + +/* Program Commands */ +#define LP5562_CMD_DISABLE 0x00 +#define LP5562_CMD_LOAD 0x15 +#define LP5562_CMD_RUN 0x2A +#define LP5562_CMD_DIRECT 0x3F +#define LP5562_PATTERN_OFF 0 + +static inline void lp5562_wait_opmode_done(void) +{ + /* operation mode change needs to be longer than 153 us */ + usleep_range(200, 300); +} + +static inline void lp5562_wait_enable_done(void) +{ + /* it takes more 488 us to update ENABLE register */ + usleep_range(500, 600); +} + +static void lp5562_set_led_current(struct lp55xx_led *led, u8 led_current) +{ + u8 addr[] = { + LP5562_REG_R_CURRENT, + LP5562_REG_G_CURRENT, + LP5562_REG_B_CURRENT, + LP5562_REG_W_CURRENT, + }; + + led->led_current = led_current; + lp55xx_write(led->chip, addr[led->chan_nr], led_current); +} + +static void lp5562_load_engine(struct lp55xx_chip *chip) +{ + enum lp55xx_engine_index idx = chip->engine_idx; + u8 mask[] = { + [LP55XX_ENGINE_1] = LP5562_MODE_ENG1_M, + [LP55XX_ENGINE_2] = LP5562_MODE_ENG2_M, + [LP55XX_ENGINE_3] = LP5562_MODE_ENG3_M, + }; + + u8 val[] = { + [LP55XX_ENGINE_1] = LP5562_LOAD_ENG1, + [LP55XX_ENGINE_2] = LP5562_LOAD_ENG2, + [LP55XX_ENGINE_3] = LP5562_LOAD_ENG3, + }; + + lp55xx_update_bits(chip, LP5562_REG_OP_MODE, mask[idx], val[idx]); + + lp5562_wait_opmode_done(); +} + +static void lp5562_stop_engine(struct lp55xx_chip *chip) +{ + lp55xx_write(chip, LP5562_REG_OP_MODE, LP5562_CMD_DISABLE); + lp5562_wait_opmode_done(); +} + +static void lp5562_run_engine(struct lp55xx_chip *chip, bool start) +{ + int ret; + u8 mode; + u8 exec; + + /* stop engine */ + if (!start) { + lp55xx_write(chip, LP5562_REG_ENABLE, LP5562_ENABLE_DEFAULT); + lp5562_wait_enable_done(); + lp5562_stop_engine(chip); + lp55xx_write(chip, LP5562_REG_ENG_SEL, LP5562_ENG_SEL_PWM); + lp55xx_write(chip, LP5562_REG_OP_MODE, LP5562_CMD_DIRECT); + lp5562_wait_opmode_done(); + return; + } + + /* + * To run the engine, + * operation mode and enable register should updated at the same time + */ + + ret = lp55xx_read(chip, LP5562_REG_OP_MODE, &mode); + if (ret) + return; + + ret = lp55xx_read(chip, LP5562_REG_ENABLE, &exec); + if (ret) + return; + + /* change operation mode to RUN only when each engine is loading */ + if (LP5562_ENG1_IS_LOADING(mode)) { + mode = (mode & ~LP5562_MODE_ENG1_M) | LP5562_RUN_ENG1; + exec = (exec & ~LP5562_EXEC_ENG1_M) | LP5562_RUN_ENG1; + } + + if (LP5562_ENG2_IS_LOADING(mode)) { + mode = (mode & ~LP5562_MODE_ENG2_M) | LP5562_RUN_ENG2; + exec = (exec & ~LP5562_EXEC_ENG2_M) | LP5562_RUN_ENG2; + } + + if (LP5562_ENG3_IS_LOADING(mode)) { + mode = (mode & ~LP5562_MODE_ENG3_M) | LP5562_RUN_ENG3; + exec = (exec & ~LP5562_EXEC_ENG3_M) | LP5562_RUN_ENG3; + } + + lp55xx_write(chip, LP5562_REG_OP_MODE, mode); + lp5562_wait_opmode_done(); + + lp55xx_update_bits(chip, LP5562_REG_ENABLE, LP5562_EXEC_M, exec); + lp5562_wait_enable_done(); +} + +static int lp5562_update_firmware(struct lp55xx_chip *chip, + const u8 *data, size_t size) +{ + enum lp55xx_engine_index idx = chip->engine_idx; + u8 pattern[LP5562_PROGRAM_LENGTH] = {0}; + u8 addr[] = { + [LP55XX_ENGINE_1] = LP5562_REG_PROG_MEM_ENG1, + [LP55XX_ENGINE_2] = LP5562_REG_PROG_MEM_ENG2, + [LP55XX_ENGINE_3] = LP5562_REG_PROG_MEM_ENG3, + }; + unsigned cmd; + char c[3]; + int program_size; + int nrchars; + int offset = 0; + int ret; + int i; + + /* clear program memory before updating */ + for (i = 0; i < LP5562_PROGRAM_LENGTH; i++) + lp55xx_write(chip, addr[idx] + i, 0); + + i = 0; + while ((offset < size - 1) && (i < LP5562_PROGRAM_LENGTH)) { + /* separate sscanfs because length is working only for %s */ + ret = sscanf(data + offset, "%2s%n ", c, &nrchars); + if (ret != 1) + goto err; + + ret = sscanf(c, "%2x", &cmd); + if (ret != 1) + goto err; + + pattern[i] = (u8)cmd; + offset += nrchars; + i++; + } + + /* Each instruction is 16bit long. Check that length is even */ + if (i % 2) + goto err; + + program_size = i; + for (i = 0; i < program_size; i++) + lp55xx_write(chip, addr[idx] + i, pattern[i]); + + return 0; + +err: + dev_err(&chip->cl->dev, "wrong pattern format\n"); + return -EINVAL; +} + +static void lp5562_firmware_loaded(struct lp55xx_chip *chip) +{ + const struct firmware *fw = chip->fw; + + if (fw->size > LP5562_PROGRAM_LENGTH) { + dev_err(&chip->cl->dev, "firmware data size overflow: %zu\n", + fw->size); + return; + } + + /* + * Program momery sequence + * 1) set engine mode to "LOAD" + * 2) write firmware data into program memory + */ + + lp5562_load_engine(chip); + lp5562_update_firmware(chip, fw->data, fw->size); +} + +static int lp5562_post_init_device(struct lp55xx_chip *chip) +{ + int ret; + u8 update_cfg = chip->pdata->update_config ? : LP5562_DEFAULT_CFG; + + /* Set all PWMs to direct control mode */ + ret = lp55xx_write(chip, LP5562_REG_OP_MODE, LP5562_CMD_DIRECT); + if (ret) + return ret; + + lp5562_wait_opmode_done(); + + ret = lp55xx_write(chip, LP5562_REG_CONFIG, update_cfg); + if (ret) + return ret; + + /* Initialize all channels PWM to zero -> leds off */ + lp55xx_write(chip, LP5562_REG_R_PWM, 0); + lp55xx_write(chip, LP5562_REG_G_PWM, 0); + lp55xx_write(chip, LP5562_REG_B_PWM, 0); + lp55xx_write(chip, LP5562_REG_W_PWM, 0); + + /* Set LED map as register PWM by default */ + lp55xx_write(chip, LP5562_REG_ENG_SEL, LP5562_ENG_SEL_PWM); + + return 0; +} + +static void lp5562_led_brightness_work(struct work_struct *work) +{ + struct lp55xx_led *led = container_of(work, struct lp55xx_led, + brightness_work); + struct lp55xx_chip *chip = led->chip; + u8 addr[] = { + LP5562_REG_R_PWM, + LP5562_REG_G_PWM, + LP5562_REG_B_PWM, + LP5562_REG_W_PWM, + }; + + mutex_lock(&chip->lock); + lp55xx_write(chip, addr[led->chan_nr], led->brightness); + mutex_unlock(&chip->lock); +} + +static void lp5562_write_program_memory(struct lp55xx_chip *chip, + u8 base, const u8 *rgb, int size) +{ + int i; + + if (!rgb || size <= 0) + return; + + for (i = 0; i < size; i++) + lp55xx_write(chip, base + i, *(rgb + i)); + + lp55xx_write(chip, base + i, 0); + lp55xx_write(chip, base + i + 1, 0); +} + +/* check the size of program count */ +static inline bool _is_pc_overflow(struct lp55xx_predef_pattern *ptn) +{ + return (ptn->size_r >= LP5562_PROGRAM_LENGTH || + ptn->size_g >= LP5562_PROGRAM_LENGTH || + ptn->size_b >= LP5562_PROGRAM_LENGTH); +} + +static int lp5562_run_predef_led_pattern(struct lp55xx_chip *chip, int mode) +{ + struct lp55xx_predef_pattern *ptn; + int i; + + if (mode == LP5562_PATTERN_OFF) { + lp5562_run_engine(chip, false); + return 0; + } + + ptn = chip->pdata->patterns + (mode - 1); + if (!ptn || _is_pc_overflow(ptn)) { + dev_err(&chip->cl->dev, "invalid pattern data\n"); + return -EINVAL; + } + + lp5562_stop_engine(chip); + + /* Set LED map as RGB */ + lp55xx_write(chip, LP5562_REG_ENG_SEL, LP5562_ENG_SEL_RGB); + + /* Load engines */ + for (i = LP55XX_ENGINE_1; i <= LP55XX_ENGINE_3; i++) { + chip->engine_idx = i; + lp5562_load_engine(chip); + } + + /* Clear program registers */ + lp55xx_write(chip, LP5562_REG_PROG_MEM_ENG1, 0); + lp55xx_write(chip, LP5562_REG_PROG_MEM_ENG1 + 1, 0); + lp55xx_write(chip, LP5562_REG_PROG_MEM_ENG2, 0); + lp55xx_write(chip, LP5562_REG_PROG_MEM_ENG2 + 1, 0); + lp55xx_write(chip, LP5562_REG_PROG_MEM_ENG3, 0); + lp55xx_write(chip, LP5562_REG_PROG_MEM_ENG3 + 1, 0); + + /* Program engines */ + lp5562_write_program_memory(chip, LP5562_REG_PROG_MEM_ENG1, + ptn->r, ptn->size_r); + lp5562_write_program_memory(chip, LP5562_REG_PROG_MEM_ENG2, + ptn->g, ptn->size_g); + lp5562_write_program_memory(chip, LP5562_REG_PROG_MEM_ENG3, + ptn->b, ptn->size_b); + + /* Run engines */ + lp5562_run_engine(chip, true); + + return 0; +} + +static ssize_t lp5562_store_pattern(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t len) +{ + struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev)); + struct lp55xx_chip *chip = led->chip; + struct lp55xx_predef_pattern *ptn = chip->pdata->patterns; + int num_patterns = chip->pdata->num_patterns; + unsigned long mode; + int ret; + + ret = kstrtoul(buf, 0, &mode); + if (ret) + return ret; + + if (mode > num_patterns || !ptn) + return -EINVAL; + + mutex_lock(&chip->lock); + ret = lp5562_run_predef_led_pattern(chip, mode); + mutex_unlock(&chip->lock); + + if (ret) + return ret; + + return len; +} + +static ssize_t lp5562_store_engine_mux(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t len) +{ + struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev)); + struct lp55xx_chip *chip = led->chip; + u8 mask; + u8 val; + + /* LED map + * R ... Engine 1 (fixed) + * G ... Engine 2 (fixed) + * B ... Engine 3 (fixed) + * W ... Engine 1 or 2 or 3 + */ + + if (sysfs_streq(buf, "RGB")) { + mask = LP5562_ENG_FOR_RGB_M; + val = LP5562_ENG_SEL_RGB; + } else if (sysfs_streq(buf, "W")) { + enum lp55xx_engine_index idx = chip->engine_idx; + + mask = LP5562_ENG_FOR_W_M; + switch (idx) { + case LP55XX_ENGINE_1: + val = LP5562_ENG1_FOR_W; + break; + case LP55XX_ENGINE_2: + val = LP5562_ENG2_FOR_W; + break; + case LP55XX_ENGINE_3: + val = LP5562_ENG3_FOR_W; + break; + default: + return -EINVAL; + } + + } else { + dev_err(dev, "choose RGB or W\n"); + return -EINVAL; + } + + mutex_lock(&chip->lock); + lp55xx_update_bits(chip, LP5562_REG_ENG_SEL, mask, val); + mutex_unlock(&chip->lock); + + return len; +} + +static DEVICE_ATTR(led_pattern, S_IWUSR, NULL, lp5562_store_pattern); +static DEVICE_ATTR(engine_mux, S_IWUSR, NULL, lp5562_store_engine_mux); + +static struct attribute *lp5562_attributes[] = { + &dev_attr_led_pattern.attr, + &dev_attr_engine_mux.attr, + NULL, +}; + +static const struct attribute_group lp5562_group = { + .attrs = lp5562_attributes, +}; + +/* Chip specific configurations */ +static struct lp55xx_device_config lp5562_cfg = { + .max_channel = LP5562_MAX_LEDS, + .reset = { + .addr = LP5562_REG_RESET, + .val = LP5562_RESET, + }, + .enable = { + .addr = LP5562_REG_ENABLE, + .val = LP5562_ENABLE_DEFAULT, + }, + .post_init_device = lp5562_post_init_device, + .set_led_current = lp5562_set_led_current, + .brightness_work_fn = lp5562_led_brightness_work, + .run_engine = lp5562_run_engine, + .firmware_cb = lp5562_firmware_loaded, + .dev_attr_group = &lp5562_group, +}; + +static int lp5562_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + int ret; + struct lp55xx_chip *chip; + struct lp55xx_led *led; + struct lp55xx_platform_data *pdata = client->dev.platform_data; + + if (!pdata) { + dev_err(&client->dev, "no platform data\n"); + return -EINVAL; + } + + chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL); + if (!chip) + return -ENOMEM; + + led = devm_kzalloc(&client->dev, + sizeof(*led) * pdata->num_channels, GFP_KERNEL); + if (!led) + return -ENOMEM; + + chip->cl = client; + chip->pdata = pdata; + chip->cfg = &lp5562_cfg; + + mutex_init(&chip->lock); + + i2c_set_clientdata(client, led); + + ret = lp55xx_init_device(chip); + if (ret) + goto err_init; + + ret = lp55xx_register_leds(led, chip); + if (ret) + goto err_register_leds; + + ret = lp55xx_register_sysfs(chip); + if (ret) { + dev_err(&client->dev, "registering sysfs failed\n"); + goto err_register_sysfs; + } + + return 0; + +err_register_sysfs: + lp55xx_unregister_leds(led, chip); +err_register_leds: + lp55xx_deinit_device(chip); +err_init: + return ret; +} + +static int lp5562_remove(struct i2c_client *client) +{ + struct lp55xx_led *led = i2c_get_clientdata(client); + struct lp55xx_chip *chip = led->chip; + + lp5562_stop_engine(chip); + + lp55xx_unregister_sysfs(chip); + lp55xx_unregister_leds(led, chip); + lp55xx_deinit_device(chip); + + return 0; +} + +static const struct i2c_device_id lp5562_id[] = { + { "lp5562", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, lp5562_id); + +static struct i2c_driver lp5562_driver = { + .driver = { + .name = "lp5562", + }, + .probe = lp5562_probe, + .remove = lp5562_remove, + .id_table = lp5562_id, +}; + +module_i2c_driver(lp5562_driver); + +MODULE_DESCRIPTION("Texas Instruments LP5562 LED Driver"); +MODULE_AUTHOR("Milo Kim"); +MODULE_LICENSE("GPL"); diff --git a/drivers/leds/leds-lp55xx-common.c b/drivers/leds/leds-lp55xx-common.c index d9eb84157423..8a388a4afed7 100644 --- a/drivers/leds/leds-lp55xx-common.c +++ b/drivers/leds/leds-lp55xx-common.c @@ -1,5 +1,5 @@ /* - * LP5521/LP5523/LP55231 Common Driver + * LP5521/LP5523/LP55231/LP5562 Common Driver * * Copyright 2012 Texas Instruments * diff --git a/include/linux/platform_data/leds-lp55xx.h b/include/linux/platform_data/leds-lp55xx.h index 1509570d5a3f..1f1041e8b4fc 100644 --- a/include/linux/platform_data/leds-lp55xx.h +++ b/include/linux/platform_data/leds-lp55xx.h @@ -32,6 +32,13 @@ #define LP5521_CLK_INT 1 /* Internal clock */ #define LP5521_CLK_AUTO 2 /* Automatic clock selection */ +/* Bits in LP5562 CONFIG register */ +#define LP5562_PWM_HF LP5521_PWM_HF +#define LP5562_PWRSAVE_EN LP5521_PWRSAVE_EN +#define LP5562_CLK_SRC_EXT LP5521_CLK_SRC_EXT +#define LP5562_CLK_INT LP5521_CLK_INT +#define LP5562_CLK_AUTO LP5521_CLK_AUTO + struct lp55xx_led_config { const char *name; u8 chan_nr; @@ -40,9 +47,9 @@ struct lp55xx_led_config { }; struct lp55xx_predef_pattern { - u8 *r; - u8 *g; - u8 *b; + const u8 *r; + const u8 *g; + const u8 *b; u8 size_r; u8 size_g; u8 size_b; |