summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
Diffstat
-rw-r--r--drivers/net/ethernet/intel/e1000/e1000_ethtool.c39
-rw-r--r--drivers/net/ethernet/intel/e1000/e1000_main.c4
-rw-r--r--drivers/net/ethernet/intel/e1000e/ethtool.c41
-rw-r--r--drivers/net/ethernet/intel/e1000e/phy.c31
-rw-r--r--drivers/net/ethernet/intel/igb/e1000_phy.c29
-rw-r--r--drivers/net/ethernet/intel/igb/e1000_phy.h5
-rw-r--r--drivers/net/ethernet/intel/igb/igb_ethtool.c42
-rw-r--r--drivers/net/ethernet/intel/igb/igb_main.c4
-rw-r--r--include/linux/ethtool.h17
9 files changed, 198 insertions, 14 deletions
diff --git a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
index 736a7d987db5..9089d00f1421 100644
--- a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
@@ -174,6 +174,20 @@ static int e1000_get_settings(struct net_device *netdev,
ecmd->autoneg = ((hw->media_type == e1000_media_type_fiber) ||
hw->autoneg) ? AUTONEG_ENABLE : AUTONEG_DISABLE;
+
+ /* MDI-X => 1; MDI => 0 */
+ if ((hw->media_type == e1000_media_type_copper) &&
+ netif_carrier_ok(netdev))
+ ecmd->eth_tp_mdix = (!!adapter->phy_info.mdix_mode ?
+ ETH_TP_MDI_X :
+ ETH_TP_MDI);
+ else
+ ecmd->eth_tp_mdix = ETH_TP_MDI_INVALID;
+
+ if (hw->mdix == AUTO_ALL_MODES)
+ ecmd->eth_tp_mdix_ctrl = ETH_TP_MDI_AUTO;
+ else
+ ecmd->eth_tp_mdix_ctrl = hw->mdix;
return 0;
}
@@ -183,6 +197,22 @@ static int e1000_set_settings(struct net_device *netdev,
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
+ /*
+ * MDI setting is only allowed when autoneg enabled because
+ * some hardware doesn't allow MDI setting when speed or
+ * duplex is forced.
+ */
+ if (ecmd->eth_tp_mdix_ctrl) {
+ if (hw->media_type != e1000_media_type_copper)
+ return -EOPNOTSUPP;
+
+ if ((ecmd->eth_tp_mdix_ctrl != ETH_TP_MDI_AUTO) &&
+ (ecmd->autoneg != AUTONEG_ENABLE)) {
+ e_err(drv, "forcing MDI/MDI-X state is not supported when link speed and/or duplex are forced\n");
+ return -EINVAL;
+ }
+ }
+
while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
msleep(1);
@@ -199,12 +229,21 @@ static int e1000_set_settings(struct net_device *netdev,
ecmd->advertising = hw->autoneg_advertised;
} else {
u32 speed = ethtool_cmd_speed(ecmd);
+ /* calling this overrides forced MDI setting */
if (e1000_set_spd_dplx(adapter, speed, ecmd->duplex)) {
clear_bit(__E1000_RESETTING, &adapter->flags);
return -EINVAL;
}
}
+ /* MDI-X => 2; MDI => 1; Auto => 3 */
+ if (ecmd->eth_tp_mdix_ctrl) {
+ if (ecmd->eth_tp_mdix_ctrl == ETH_TP_MDI_AUTO)
+ hw->mdix = AUTO_ALL_MODES;
+ else
+ hw->mdix = ecmd->eth_tp_mdix_ctrl;
+ }
+
/* reset the link */
if (netif_running(adapter->netdev)) {
diff --git a/drivers/net/ethernet/intel/e1000/e1000_main.c b/drivers/net/ethernet/intel/e1000/e1000_main.c
index 3bfbb8df8989..0ae2fcfa5124 100644
--- a/drivers/net/ethernet/intel/e1000/e1000_main.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_main.c
@@ -4939,6 +4939,10 @@ int e1000_set_spd_dplx(struct e1000_adapter *adapter, u32 spd, u8 dplx)
default:
goto err_inval;
}
+
+ /* clear MDI, MDI(-X) override is only allowed when autoneg enabled */
+ hw->mdix = AUTO_ALL_MODES;
+
return 0;
err_inval:
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 0349e2478df8..2e76f06720fd 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -199,6 +199,11 @@ static int e1000_get_settings(struct net_device *netdev,
else
ecmd->eth_tp_mdix = ETH_TP_MDI_INVALID;
+ if (hw->phy.mdix == AUTO_ALL_MODES)
+ ecmd->eth_tp_mdix_ctrl = ETH_TP_MDI_AUTO;
+ else
+ ecmd->eth_tp_mdix_ctrl = hw->phy.mdix;
+
return 0;
}
@@ -241,6 +246,10 @@ static int e1000_set_spd_dplx(struct e1000_adapter *adapter, u32 spd, u8 dplx)
default:
goto err_inval;
}
+
+ /* clear MDI, MDI(-X) override is only allowed when autoneg enabled */
+ adapter->hw.phy.mdix = AUTO_ALL_MODES;
+
return 0;
err_inval:
@@ -264,6 +273,22 @@ static int e1000_set_settings(struct net_device *netdev,
return -EINVAL;
}
+ /*
+ * MDI setting is only allowed when autoneg enabled because
+ * some hardware doesn't allow MDI setting when speed or
+ * duplex is forced.
+ */
+ if (ecmd->eth_tp_mdix_ctrl) {
+ if (hw->phy.media_type != e1000_media_type_copper)
+ return -EOPNOTSUPP;
+
+ if ((ecmd->eth_tp_mdix_ctrl != ETH_TP_MDI_AUTO) &&
+ (ecmd->autoneg != AUTONEG_ENABLE)) {
+ e_err("forcing MDI/MDI-X state is not supported when link speed and/or duplex are forced\n");
+ return -EINVAL;
+ }
+ }
+
while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
usleep_range(1000, 2000);
@@ -282,20 +307,32 @@ static int e1000_set_settings(struct net_device *netdev,
hw->fc.requested_mode = e1000_fc_default;
} else {
u32 speed = ethtool_cmd_speed(ecmd);
+ /* calling this overrides forced MDI setting */
if (e1000_set_spd_dplx(adapter, speed, ecmd->duplex)) {
clear_bit(__E1000_RESETTING, &adapter->state);
return -EINVAL;
}
}
+ /* MDI-X => 2; MDI => 1; Auto => 3 */
+ if (ecmd->eth_tp_mdix_ctrl) {
+ /*
+ * fix up the value for auto (3 => 0) as zero is mapped
+ * internally to auto
+ */
+ if (ecmd->eth_tp_mdix_ctrl == ETH_TP_MDI_AUTO)
+ hw->phy.mdix = AUTO_ALL_MODES;
+ else
+ hw->phy.mdix = ecmd->eth_tp_mdix_ctrl;
+ }
+
/* reset the link */
if (netif_running(adapter->netdev)) {
e1000e_down(adapter);
e1000e_up(adapter);
- } else {
+ } else
e1000e_reset(adapter);
- }
clear_bit(__E1000_RESETTING, &adapter->state);
return 0;
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index b860d4f7ea2a..fc62a3f3a5be 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -84,8 +84,9 @@ static const u16 e1000_igp_2_cable_length_table[] = {
#define I82577_PHY_STATUS2_SPEED_1000MBPS 0x0200
/* I82577 PHY Control 2 */
-#define I82577_PHY_CTRL2_AUTO_MDIX 0x0400
-#define I82577_PHY_CTRL2_FORCE_MDI_MDIX 0x0200
+#define I82577_PHY_CTRL2_MANUAL_MDIX 0x0200
+#define I82577_PHY_CTRL2_AUTO_MDI_MDIX 0x0400
+#define I82577_PHY_CTRL2_MDIX_CFG_MASK 0x0600
/* I82577 PHY Diagnostics Status */
#define I82577_DSTATUS_CABLE_LENGTH 0x03FC
@@ -702,6 +703,32 @@ s32 e1000_copper_link_setup_82577(struct e1000_hw *hw)
if (ret_val)
return ret_val;
+ /* Set MDI/MDIX mode */
+ ret_val = e1e_rphy(hw, I82577_PHY_CTRL_2, &phy_data);
+ if (ret_val)
+ return ret_val;
+ phy_data &= ~I82577_PHY_CTRL2_MDIX_CFG_MASK;
+ /*
+ * Options:
+ * 0 - Auto (default)
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ */
+ switch (hw->phy.mdix) {
+ case 1:
+ break;
+ case 2:
+ phy_data |= I82577_PHY_CTRL2_MANUAL_MDIX;
+ break;
+ case 0:
+ default:
+ phy_data |= I82577_PHY_CTRL2_AUTO_MDI_MDIX;
+ break;
+ }
+ ret_val = e1e_wphy(hw, I82577_PHY_CTRL_2, phy_data);
+ if (ret_val)
+ return ret_val;
+
return e1000_set_master_slave_mode(hw);
}
diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.c b/drivers/net/ethernet/intel/igb/e1000_phy.c
index 7be98b6f1052..3404bc79f4ca 100644
--- a/drivers/net/ethernet/intel/igb/e1000_phy.c
+++ b/drivers/net/ethernet/intel/igb/e1000_phy.c
@@ -464,6 +464,32 @@ s32 igb_copper_link_setup_82580(struct e1000_hw *hw)
phy_data |= I82580_CFG_ENABLE_DOWNSHIFT;
ret_val = phy->ops.write_reg(hw, I82580_CFG_REG, phy_data);
+ if (ret_val)
+ goto out;
+
+ /* Set MDI/MDIX mode */
+ ret_val = phy->ops.read_reg(hw, I82580_PHY_CTRL_2, &phy_data);
+ if (ret_val)
+ goto out;
+ phy_data &= ~I82580_PHY_CTRL2_MDIX_CFG_MASK;
+ /*
+ * Options:
+ * 0 - Auto (default)
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ */
+ switch (hw->phy.mdix) {
+ case 1:
+ break;
+ case 2:
+ phy_data |= I82580_PHY_CTRL2_MANUAL_MDIX;
+ break;
+ case 0:
+ default:
+ phy_data |= I82580_PHY_CTRL2_AUTO_MDI_MDIX;
+ break;
+ }
+ ret_val = hw->phy.ops.write_reg(hw, I82580_PHY_CTRL_2, phy_data);
out:
return ret_val;
@@ -2246,8 +2272,7 @@ s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw)
if (ret_val)
goto out;
- phy_data &= ~I82580_PHY_CTRL2_AUTO_MDIX;
- phy_data &= ~I82580_PHY_CTRL2_FORCE_MDI_MDIX;
+ phy_data &= ~I82580_PHY_CTRL2_MDIX_CFG_MASK;
ret_val = phy->ops.write_reg(hw, I82580_PHY_CTRL_2, phy_data);
if (ret_val)
diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.h b/drivers/net/ethernet/intel/igb/e1000_phy.h
index 34e40619f16b..6ac3299bfcb9 100644
--- a/drivers/net/ethernet/intel/igb/e1000_phy.h
+++ b/drivers/net/ethernet/intel/igb/e1000_phy.h
@@ -111,8 +111,9 @@ s32 igb_check_polarity_m88(struct e1000_hw *hw);
#define I82580_PHY_STATUS2_SPEED_100MBPS 0x0100
/* I82580 PHY Control 2 */
-#define I82580_PHY_CTRL2_AUTO_MDIX 0x0400
-#define I82580_PHY_CTRL2_FORCE_MDI_MDIX 0x0200
+#define I82580_PHY_CTRL2_MANUAL_MDIX 0x0200
+#define I82580_PHY_CTRL2_AUTO_MDI_MDIX 0x0400
+#define I82580_PHY_CTRL2_MDIX_CFG_MASK 0x0600
/* I82580 PHY Diagnostics Status */
#define I82580_DSTATUS_CABLE_LENGTH 0x03FC
diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index 70591117051b..be02168f1308 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -198,6 +198,19 @@ static int igb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
}
ecmd->autoneg = hw->mac.autoneg ? AUTONEG_ENABLE : AUTONEG_DISABLE;
+
+ /* MDI-X => 2; MDI =>1; Invalid =>0 */
+ if (hw->phy.media_type == e1000_media_type_copper)
+ ecmd->eth_tp_mdix = hw->phy.is_mdix ? ETH_TP_MDI_X :
+ ETH_TP_MDI;
+ else
+ ecmd->eth_tp_mdix = ETH_TP_MDI_INVALID;
+
+ if (hw->phy.mdix == AUTO_ALL_MODES)
+ ecmd->eth_tp_mdix_ctrl = ETH_TP_MDI_AUTO;
+ else
+ ecmd->eth_tp_mdix_ctrl = hw->phy.mdix;
+
return 0;
}
@@ -214,6 +227,22 @@ static int igb_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
return -EINVAL;
}
+ /*
+ * MDI setting is only allowed when autoneg enabled because
+ * some hardware doesn't allow MDI setting when speed or
+ * duplex is forced.
+ */
+ if (ecmd->eth_tp_mdix_ctrl) {
+ if (hw->phy.media_type != e1000_media_type_copper)
+ return -EOPNOTSUPP;
+
+ if ((ecmd->eth_tp_mdix_ctrl != ETH_TP_MDI_AUTO) &&
+ (ecmd->autoneg != AUTONEG_ENABLE)) {
+ dev_err(&adapter->pdev->dev, "forcing MDI/MDI-X state is not supported when link speed and/or duplex are forced\n");
+ return -EINVAL;
+ }
+ }
+
while (test_and_set_bit(__IGB_RESETTING, &adapter->state))
msleep(1);
@@ -227,12 +256,25 @@ static int igb_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
hw->fc.requested_mode = e1000_fc_default;
} else {
u32 speed = ethtool_cmd_speed(ecmd);
+ /* calling this overrides forced MDI setting */
if (igb_set_spd_dplx(adapter, speed, ecmd->duplex)) {
clear_bit(__IGB_RESETTING, &adapter->state);
return -EINVAL;
}
}
+ /* MDI-X => 2; MDI => 1; Auto => 3 */
+ if (ecmd->eth_tp_mdix_ctrl) {
+ /*
+ * fix up the value for auto (3 => 0) as zero is mapped
+ * internally to auto
+ */
+ if (ecmd->eth_tp_mdix_ctrl == ETH_TP_MDI_AUTO)
+ hw->phy.mdix = AUTO_ALL_MODES;
+ else
+ hw->phy.mdix = ecmd->eth_tp_mdix_ctrl;
+ }
+
/* reset the link */
if (netif_running(adapter->netdev)) {
igb_down(adapter);
diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c
index 48cc4fb1a307..73cc273ef98b 100644
--- a/drivers/net/ethernet/intel/igb/igb_main.c
+++ b/drivers/net/ethernet/intel/igb/igb_main.c
@@ -6675,6 +6675,10 @@ int igb_set_spd_dplx(struct igb_adapter *adapter, u32 spd, u8 dplx)
default:
goto err_inval;
}
+
+ /* clear MDI, MDI(-X) override is only allowed when autoneg enabled */
+ adapter->hw.phy.mdix = AUTO_ALL_MODES;
+
return 0;
err_inval:
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index 21eff418091b..fcb4f8e60c1c 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -45,8 +45,10 @@ struct ethtool_cmd {
* bits) in Mbps. Please use
* ethtool_cmd_speed()/_set() to
* access it */
- __u8 eth_tp_mdix;
- __u8 reserved2;
+ __u8 eth_tp_mdix; /* twisted pair MDI-X status */
+ __u8 eth_tp_mdix_ctrl; /* twisted pair MDI-X control, when set,
+ * link should be renegotiated if necessary
+ */
__u32 lp_advertising; /* Features the link partner advertises */
__u32 reserved[2];
};
@@ -1229,10 +1231,13 @@ struct ethtool_ops {
#define AUTONEG_DISABLE 0x00
#define AUTONEG_ENABLE 0x01
-/* Mode MDI or MDI-X */
-#define ETH_TP_MDI_INVALID 0x00
-#define ETH_TP_MDI 0x01
-#define ETH_TP_MDI_X 0x02
+/* MDI or MDI-X status/control - if MDI/MDI_X/AUTO is set then
+ * the driver is required to renegotiate link
+ */
+#define ETH_TP_MDI_INVALID 0x00 /* status: unknown; control: unsupported */
+#define ETH_TP_MDI 0x01 /* status: MDI; control: force MDI */
+#define ETH_TP_MDI_X 0x02 /* status: MDI-X; control: force MDI-X */
+#define ETH_TP_MDI_AUTO 0x03 /* control: auto-select */
/* Wake-On-Lan options. */
#define WAKE_PHY (1 << 0)
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-04 16:42:07 +0000