diff options
| author | Andy Gospodarek <andy@greyhouse.net> | 2009-12-14 10:48:58 +0000 |
|---|---|---|
| committer | David S. Miller <davem@davemloft.net> | 2010-01-03 21:17:16 -0800 |
| commit | 1f3c8804acba841b5573b953f5560d2683d2db0d (patch) | |
| tree | 453fae141b4a37e72ee0513ea1816fbff8f1cf8a /net/8021q | |
| parent | 3a999e6eb5d277cd6a321dcda3fc43c3d9e4e4b8 (diff) | |
| download | linux-1f3c8804acba841b5573b953f5560d2683d2db0d.tar.bz2 | |
bonding: allow arp_ip_targets on separate vlans to use arp validation
This allows a bond device to specify an arp_ip_target as a host that is
not on the same vlan as the base bond device and still use arp
validation. A configuration like this, now works:
BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3"
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
inet6 fe80::213:21ff:febe:33e9/64 scope link
valid_lft forever preferred_lft forever
9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100
inet6 fe80::213:21ff:febe:33e9/64 scope link
valid_lft forever preferred_lft forever
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 1000
ARP IP target/s (n.n.n.n form): 10.0.100.1
Slave Interface: eth1
MII Status: up
Link Failure Count: 1
Permanent HW addr: 00:40:05:30:ff:30
Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:13:21:be:33:e9
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Diffstat (limited to 'net/8021q')
| -rw-r--r-- | net/8021q/vlan_core.c | 2 |
1 files changed, 2 insertions, 0 deletions
diff --git a/net/8021q/vlan_core.c b/net/8021q/vlan_core.c index e75a2f3b10af..c0316e0ca6e8 100644 --- a/net/8021q/vlan_core.c +++ b/net/8021q/vlan_core.c @@ -14,6 +14,7 @@ int __vlan_hwaccel_rx(struct sk_buff *skb, struct vlan_group *grp, if (skb_bond_should_drop(skb)) goto drop; + skb->skb_iif = skb->dev->ifindex; __vlan_hwaccel_put_tag(skb, vlan_tci); skb->dev = vlan_group_get_device(grp, vlan_tci & VLAN_VID_MASK); @@ -85,6 +86,7 @@ vlan_gro_common(struct napi_struct *napi, struct vlan_group *grp, if (skb_bond_should_drop(skb)) goto drop; + skb->skb_iif = skb->dev->ifindex; __vlan_hwaccel_put_tag(skb, vlan_tci); skb->dev = vlan_group_get_device(grp, vlan_tci & VLAN_VID_MASK); |