Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (148 commits)
  USB: serial: fix stalled writes
  USB: remove fake "address-of" expressions
  USB: fix thread-unsafe anchor utiliy routines
  USB: usbtest: support test device with only one iso-in or iso-out endpoint
  USB: usbtest: avoid to free coherent buffer in atomic context
  USB: xhci: Set DMA mask for host.
  USB: xhci: Don't flush doorbell writes.
  USB: xhci: Reduce reads and writes of interrupter registers.
  USB: xhci: Make xhci_set_hc_event_deq() static.
  USB: xhci: Minimize HW event ring dequeue pointer writes.
  USB: xhci: Make xhci_handle_event() static.
  USB: xhci: Remove unnecessary reads of IRQ_PENDING register.
  USB: xhci: Performance - move xhci_work() into xhci_irq()
  USB: xhci: Performance - move interrupt handlers into xhci-ring.c
  USB: xhci: Performance - move functions that find ep ring.
  USB:: fix linux/usb.h kernel-doc warnings
  USB: add USB serial ssu100 driver
  USB: usb-storage: implement autosuspend
  USB: ehci: fix remove of ehci debugfs dir
  USB: Add USB 2.0 to ssb ohci driver
  ...

8 files changed, 107 insertions, 19 deletions

diff --git a/include/linux/usb.h b/include/linux/usb.h
index d5922a877994..35fe6ab222bb 100644
--- a/include/linux/usb.h
+++ b/include/linux/usb.h
@@ -127,6 +127,8 @@ enum usb_interface_condition {
  *      queued reset so that usb_cancel_queued_reset() doesn't try to
  *      remove from the workqueue when running inside the worker
  *      thread. See __usb_queue_reset_device().
+ * @resetting_device: USB core reset the device, so use alt setting 0 as
+ *	current; needs bandwidth alloc after reset.
  *
  * USB device drivers attach to interfaces on a physical device.  Each
  * interface encapsulates a single high level function, such as feeding
@@ -843,7 +845,7 @@ struct usb_driver {
 
 	void (*disconnect) (struct usb_interface *intf);
 
-	int (*ioctl) (struct usb_interface *intf, unsigned int code,
+	int (*unlocked_ioctl) (struct usb_interface *intf, unsigned int code,
 			void *buf);
 
 	int (*suspend) (struct usb_interface *intf, pm_message_t message);
@@ -1015,6 +1017,7 @@ typedef void (*usb_complete_t)(struct urb *);
  *	is a different endpoint (and pipe) from "out" endpoint two.
  *	The current configuration controls the existence, type, and
  *	maximum packet size of any given endpoint.
+ * @stream_id: the endpoint's stream ID for bulk streams
  * @dev: Identifies the USB device to perform the request.
  * @status: This is read in non-iso completion functions to get the
  *	status of the particular request.  ISO requests only use it
diff --git a/include/linux/usb/composite.h b/include/linux/usb/composite.h
index 139353efad34..890bc1472190 100644
--- a/include/linux/usb/composite.h
+++ b/include/linux/usb/composite.h
@@ -276,6 +276,8 @@ struct usb_composite_driver {
 	int			(*bind)(struct usb_composite_dev *);
 	int			(*unbind)(struct usb_composite_dev *);
 
+	void			(*disconnect)(struct usb_composite_dev *);
+
 	/* global suspend hooks */
 	void			(*suspend)(struct usb_composite_dev *);
 	void			(*resume)(struct usb_composite_dev *);
@@ -342,6 +344,10 @@ struct usb_composite_dev {
 };
 
 extern int usb_string_id(struct usb_composite_dev *c);
+extern int usb_string_ids_tab(struct usb_composite_dev *c,
+			      struct usb_string *str);
+extern int usb_string_ids_n(struct usb_composite_dev *c, unsigned n);
+
 
 /* messaging utils */
 #define DBG(d, fmt, args...) \
diff --git a/include/linux/usb/ehci_def.h b/include/linux/usb/ehci_def.h
index 80287af2a738..2e262cb15425 100644
--- a/include/linux/usb/ehci_def.h
+++ b/include/linux/usb/ehci_def.h
@@ -39,6 +39,12 @@ struct ehci_caps {
 #define HCS_N_PORTS(p)		(((p)>>0)&0xf)	/* bits 3:0, ports on HC */
 
 	u32		hcc_params;      /* HCCPARAMS - offset 0x8 */
+/* EHCI 1.1 addendum */
+#define HCC_32FRAME_PERIODIC_LIST(p)	((p)&(1 << 19))
+#define HCC_PER_PORT_CHANGE_EVENT(p)	((p)&(1 << 18))
+#define HCC_LPM(p)			((p)&(1 << 17))
+#define HCC_HW_PREFETCH(p)		((p)&(1 << 16))
+
 #define HCC_EXT_CAPS(p)		(((p)>>8)&0xff)	/* for pci extended caps */
 #define HCC_ISOC_CACHE(p)       ((p)&(1 << 7))  /* true: can cache isoc frame */
 #define HCC_ISOC_THRES(p)       (((p)>>4)&0x7)  /* bits 6:4, uframes cached */
@@ -54,6 +60,13 @@ struct ehci_regs {
 
 	/* USBCMD: offset 0x00 */
 	u32		command;
+
+/* EHCI 1.1 addendum */
+#define CMD_HIRD	(0xf<<24)	/* host initiated resume duration */
+#define CMD_PPCEE	(1<<15)		/* per port change event enable */
+#define CMD_FSP		(1<<14)		/* fully synchronized prefetch */
+#define CMD_ASPE	(1<<13)		/* async schedule prefetch enable */
+#define CMD_PSPE	(1<<12)		/* periodic schedule prefetch enable */
 /* 23:16 is r/w intr rate, in microframes; default "8" == 1/msec */
 #define CMD_PARK	(1<<11)		/* enable "park" on async qh */
 #define CMD_PARK_CNT(c)	(((c)>>8)&3)	/* how many transfers to park for */
@@ -67,6 +80,7 @@ struct ehci_regs {
 
 	/* USBSTS: offset 0x04 */
 	u32		status;
+#define STS_PPCE_MASK	(0xff<<16)	/* Per-Port change event 1-16 */
 #define STS_ASS		(1<<15)		/* Async Schedule Status */
 #define STS_PSS		(1<<14)		/* Periodic Schedule Status */
 #define STS_RECL	(1<<13)		/* Reclamation */
@@ -100,6 +114,14 @@ struct ehci_regs {
 
 	/* PORTSC: offset 0x44 */
 	u32		port_status[0];	/* up to N_PORTS */
+/* EHCI 1.1 addendum */
+#define PORTSC_SUSPEND_STS_ACK 0
+#define PORTSC_SUSPEND_STS_NYET 1
+#define PORTSC_SUSPEND_STS_STALL 2
+#define PORTSC_SUSPEND_STS_ERR 3
+
+#define PORT_DEV_ADDR	(0x7f<<25)		/* device address */
+#define PORT_SSTS	(0x3<<23)		/* suspend status */
 /* 31:23 reserved */
 #define PORT_WKOC_E	(1<<22)		/* wake on overcurrent (enable) */
 #define PORT_WKDISC_E	(1<<21)		/* wake on disconnect (enable) */
@@ -115,6 +137,7 @@ struct ehci_regs {
 #define PORT_USB11(x) (((x)&(3<<10)) == (1<<10))	/* USB 1.1 device */
 /* 11:10 for detecting lowspeed devices (reset vs release ownership) */
 /* 9 reserved */
+#define PORT_LPM	(1<<9)		/* LPM transaction */
 #define PORT_RESET	(1<<8)		/* reset port */
 #define PORT_SUSPEND	(1<<7)		/* suspend port */
 #define PORT_RESUME	(1<<6)		/* resume it */
diff --git a/include/linux/usb/functionfs.h b/include/linux/usb/functionfs.h
index a34a2a043b21..6f649c13193b 100644
--- a/include/linux/usb/functionfs.h
+++ b/include/linux/usb/functionfs.h
@@ -180,9 +180,9 @@ static int functionfs_bind(struct ffs_data *ffs, struct usb_composite_dev *cdev)
 static void functionfs_unbind(struct ffs_data *ffs)
 	__attribute__((nonnull));
 
-static int functionfs_add(struct usb_composite_dev *cdev,
-			  struct usb_configuration *c,
-			  struct ffs_data *ffs)
+static int functionfs_bind_config(struct usb_composite_dev *cdev,
+				  struct usb_configuration *c,
+				  struct ffs_data *ffs)
 	__attribute__((warn_unused_result, nonnull));
 
 
diff --git a/include/linux/usb/hcd.h b/include/linux/usb/hcd.h
index 2e3a4ea1a3da..3b571f1ffbb3 100644
--- a/include/linux/usb/hcd.h
+++ b/include/linux/usb/hcd.h
@@ -89,18 +89,33 @@ struct usb_hcd {
 	 */
 	const struct hc_driver	*driver;	/* hw-specific hooks */
 
-	/* Flags that need to be manipulated atomically */
+	/* Flags that need to be manipulated atomically because they can
+	 * change while the host controller is running.  Always use
+	 * set_bit() or clear_bit() to change their values.
+	 */
 	unsigned long		flags;
-#define HCD_FLAG_HW_ACCESSIBLE	0x00000001
-#define HCD_FLAG_SAW_IRQ	0x00000002
+#define HCD_FLAG_HW_ACCESSIBLE		0	/* at full power */
+#define HCD_FLAG_SAW_IRQ		1
+#define HCD_FLAG_POLL_RH		2	/* poll for rh status? */
+#define HCD_FLAG_POLL_PENDING		3	/* status has changed? */
+#define HCD_FLAG_WAKEUP_PENDING		4	/* root hub is resuming? */
+
+	/* The flags can be tested using these macros; they are likely to
+	 * be slightly faster than test_bit().
+	 */
+#define HCD_HW_ACCESSIBLE(hcd)	((hcd)->flags & (1U << HCD_FLAG_HW_ACCESSIBLE))
+#define HCD_SAW_IRQ(hcd)	((hcd)->flags & (1U << HCD_FLAG_SAW_IRQ))
+#define HCD_POLL_RH(hcd)	((hcd)->flags & (1U << HCD_FLAG_POLL_RH))
+#define HCD_POLL_PENDING(hcd)	((hcd)->flags & (1U << HCD_FLAG_POLL_PENDING))
+#define HCD_WAKEUP_PENDING(hcd)	((hcd)->flags & (1U << HCD_FLAG_WAKEUP_PENDING))
 
+	/* Flags that get set only during HCD registration or removal. */
 	unsigned		rh_registered:1;/* is root hub registered? */
+	unsigned		rh_pollable:1;	/* may we poll the root hub? */
 
 	/* The next flag is a stopgap, to be removed when all the HCDs
 	 * support the new root-hub polling mechanism. */
 	unsigned		uses_new_polling:1;
-	unsigned		poll_rh:1;	/* poll for rh status? */
-	unsigned		poll_pending:1;	/* status has changed? */
 	unsigned		wireless:1;	/* Wireless USB HCD */
 	unsigned		authorized_default:1;
 	unsigned		has_tt:1;	/* Integrated TT in root hub */
@@ -198,7 +213,7 @@ struct hc_driver {
 	 * a whole, not just the root hub; they're for PCI bus glue.
 	 */
 	/* called after suspending the hub, before entering D3 etc */
-	int	(*pci_suspend)(struct usb_hcd *hcd);
+	int	(*pci_suspend)(struct usb_hcd *hcd, bool do_wakeup);
 
 	/* called after entering D0 (etc), before resuming the hub */
 	int	(*pci_resume)(struct usb_hcd *hcd, bool hibernated);
@@ -299,6 +314,10 @@ struct hc_driver {
 	int	(*update_hub_device)(struct usb_hcd *, struct usb_device *hdev,
 			struct usb_tt *tt, gfp_t mem_flags);
 	int	(*reset_device)(struct usb_hcd *, struct usb_device *);
+		/* Notifies the HCD after a device is connected and its
+		 * address is set
+		 */
+	int	(*update_device)(struct usb_hcd *, struct usb_device *);
 };
 
 extern int usb_hcd_link_urb_to_ep(struct usb_hcd *hcd, struct urb *urb);
diff --git a/include/linux/usb/otg.h b/include/linux/usb/otg.h
index f8302d036a76..545cba73ccaf 100644
--- a/include/linux/usb/otg.h
+++ b/include/linux/usb/otg.h
@@ -43,13 +43,6 @@ enum usb_xceiv_events {
 	USB_EVENT_ENUMERATED,   /* gadget driver enumerated */
 };
 
-#define USB_OTG_PULLUP_ID		(1 << 0)
-#define USB_OTG_PULLDOWN_DP		(1 << 1)
-#define USB_OTG_PULLDOWN_DM		(1 << 2)
-#define USB_OTG_EXT_VBUS_INDICATOR	(1 << 3)
-#define USB_OTG_DRV_VBUS		(1 << 4)
-#define USB_OTG_DRV_VBUS_EXT		(1 << 5)
-
 struct otg_transceiver;
 
 /* for transceivers connected thru an ULPI interface, the user must
@@ -146,10 +139,10 @@ static inline int otg_io_read(struct otg_transceiver *otg, u32 reg)
 	return -EINVAL;
 }
 
-static inline int otg_io_write(struct otg_transceiver *otg, u32 reg, u32 val)
+static inline int otg_io_write(struct otg_transceiver *otg, u32 val, u32 reg)
 {
 	if (otg->io_ops && otg->io_ops->write)
-		return otg->io_ops->write(otg, reg, val);
+		return otg->io_ops->write(otg, val, reg);
 
 	return -EINVAL;
 }
diff --git a/include/linux/usb/quirks.h b/include/linux/usb/quirks.h
index 16b7f3347545..3e93de7ecbc3 100644
--- a/include/linux/usb/quirks.h
+++ b/include/linux/usb/quirks.h
@@ -26,4 +26,8 @@
    and can't handle talking to these interfaces */
 #define USB_QUIRK_HONOR_BNUMINTERFACES	0x00000020
 
+/* device needs a pause during initialization, after we read the device
+   descriptor */
+#define USB_QUIRK_DELAY_INIT		0x00000040
+
 #endif /* __LINUX_USB_QUIRKS_H */
diff --git a/include/linux/usb/ulpi.h b/include/linux/usb/ulpi.h
index 2369d07c3c87..82b1507f4735 100644
--- a/include/linux/usb/ulpi.h
+++ b/include/linux/usb/ulpi.h
@@ -11,6 +11,42 @@
 #ifndef __LINUX_USB_ULPI_H
 #define __LINUX_USB_ULPI_H
 
+#include <linux/usb/otg.h>
+/*-------------------------------------------------------------------------*/
+
+/*
+ * ULPI Flags
+ */
+#define ULPI_OTG_ID_PULLUP		(1 << 0)
+#define ULPI_OTG_DP_PULLDOWN_DIS	(1 << 1)
+#define ULPI_OTG_DM_PULLDOWN_DIS	(1 << 2)
+#define ULPI_OTG_DISCHRGVBUS		(1 << 3)
+#define ULPI_OTG_CHRGVBUS		(1 << 4)
+#define ULPI_OTG_DRVVBUS		(1 << 5)
+#define ULPI_OTG_DRVVBUS_EXT		(1 << 6)
+#define ULPI_OTG_EXTVBUSIND		(1 << 7)
+
+#define ULPI_IC_6PIN_SERIAL		(1 << 8)
+#define ULPI_IC_3PIN_SERIAL		(1 << 9)
+#define ULPI_IC_CARKIT			(1 << 10)
+#define ULPI_IC_CLKSUSPM		(1 << 11)
+#define ULPI_IC_AUTORESUME		(1 << 12)
+#define ULPI_IC_EXTVBUS_INDINV		(1 << 13)
+#define ULPI_IC_IND_PASSTHRU		(1 << 14)
+#define ULPI_IC_PROTECT_DIS		(1 << 15)
+
+#define ULPI_FC_HS			(1 << 16)
+#define ULPI_FC_FS			(1 << 17)
+#define ULPI_FC_LS			(1 << 18)
+#define ULPI_FC_FS4LS			(1 << 19)
+#define ULPI_FC_TERMSEL			(1 << 20)
+#define ULPI_FC_OP_NORM			(1 << 21)
+#define ULPI_FC_OP_NODRV		(1 << 22)
+#define ULPI_FC_OP_DIS_NRZI		(1 << 23)
+#define ULPI_FC_OP_NSYNC_NEOP		(1 << 24)
+#define ULPI_FC_RST			(1 << 25)
+#define ULPI_FC_SUSPM			(1 << 26)
+
 /*-------------------------------------------------------------------------*/
 
 /*
@@ -58,6 +94,10 @@
 
 /*-------------------------------------------------------------------------*/
 
+/*
+ * Register Bits
+ */
+
 /* Function Control */
 #define ULPI_FUNC_CTRL_XCVRSEL			(1 << 0)
 #define  ULPI_FUNC_CTRL_XCVRSEL_MASK		(3 << 0)