diff options
| author | Ard Biesheuvel <ard.biesheuvel@linaro.org> | 2017-10-02 19:31:24 +0100 |
|---|---|---|
| committer | Tejun Heo <tj@kernel.org> | 2017-10-02 12:21:30 -0700 |
| commit | d312fefea8387503375f728855c9a62de20c9665 (patch) | |
| tree | f3158ccdcb6bd390bc6f4f51ae5b3f44e6da9561 /drivers | |
| parent | 80a921e207cea3dd18038501187078669a218dab (diff) | |
| download | linux-d312fefea8387503375f728855c9a62de20c9665.tar.bz2 | |
ahci: don't ignore result code of ahci_reset_controller()
ahci_pci_reset_controller() calls ahci_reset_controller(), which may
fail, but ignores the result code and always returns success. This
may result in failures like below
ahci 0000:02:00.0: version 3.0
ahci 0000:02:00.0: enabling device (0000 -> 0003)
ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled
ahci 0000:02:00.0: controller reset failed (0xffffffff)
ahci 0000:02:00.0: failed to stop engine (-5)
... repeated many times ...
ahci 0000:02:00.0: failed to stop engine (-5)
Unable to handle kernel paging request at virtual address ffff0000093f9018
...
PC is at ahci_stop_engine+0x5c/0xd8 [libahci]
LR is at ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
...
[<ffff000000a17014>] ahci_stop_engine+0x5c/0xd8 [libahci]
[<ffff000000a196b4>] ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
[<ffff000000a197d8>] ahci_init_controller+0x80/0x168 [libahci]
[<ffff000000a260f8>] ahci_pci_init_controller+0x60/0x68 [ahci]
[<ffff000000a26f94>] ahci_init_one+0x75c/0xd88 [ahci]
[<ffff000008430324>] local_pci_probe+0x3c/0xb8
[<ffff000008431728>] pci_device_probe+0x138/0x170
[<ffff000008585e54>] driver_probe_device+0x2dc/0x458
[<ffff0000085860e4>] __driver_attach+0x114/0x118
[<ffff000008583ca8>] bus_for_each_dev+0x60/0xa0
[<ffff000008585638>] driver_attach+0x20/0x28
[<ffff0000085850b0>] bus_add_driver+0x1f0/0x2a8
[<ffff000008586ae0>] driver_register+0x60/0xf8
[<ffff00000842f9b4>] __pci_register_driver+0x3c/0x48
[<ffff000000a3001c>] ahci_pci_driver_init+0x1c/0x1000 [ahci]
[<ffff000008083918>] do_one_initcall+0x38/0x120
where an obvious hardware level failure results in an unnecessary 15 second
delay and a subsequent crash.
So record the result code of ahci_reset_controller() and relay it, rather
than ignoring it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/ata/ahci.c | 5 |
1 files changed, 4 insertions, 1 deletions
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index cb9b0e9090e3..9f78bb03bb76 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -621,8 +621,11 @@ static void ahci_pci_save_initial_config(struct pci_dev *pdev, static int ahci_pci_reset_controller(struct ata_host *host) { struct pci_dev *pdev = to_pci_dev(host->dev); + int rc; - ahci_reset_controller(host); + rc = ahci_reset_controller(host); + if (rc) + return rc; if (pdev->vendor == PCI_VENDOR_ID_INTEL) { struct ahci_host_priv *hpriv = host->private_data; |