Merge branch 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:

 - the core has now a lockless variant of i2c_smbus_xfer. Some open
   coded versions of this got removed in drivers. This also enables
   proper SCCB support in regmap.

 - locking got a more precise naming. i2c_{un}lock_adapter() had to go,
   and we know use i2c_lock_bus() consistently with flags like
   I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.

 - the gpio fault injector got a new delicate testcase

 - the bus recovery procedure got fixed to handle the new testcase
   correctly

 - a new quirk flag for controllers not able to handle zero length
   messages together with driver updates to use it

 - new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
   family S900

 - and a good set of driver improvements and bugfixes

* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
  i2c: rcar: implement STOP and REP_START according to docs
  i2c: rcar: refactor private flags
  i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
  i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
  dt-bindings: i2c: rcar: Add r8a774a1 support
  dt-bindings: i2c: sh_mobile: Add r8a774a1 support
  i2c: imx: Simplify stopped state tracking
  i2c: imx: Fix race condition in dma read
  i2c: pasemi: remove hardcoded bus numbers on smbus
  i2c: designware: Add SPDX license tag
  i2c: designware: Convert to use struct i2c_timings
  i2c: core: Parse SDA hold time from firmware
  i2c: designware-pcidrv: Mark expected switch fall-through
  i2c: amd8111: Mark expected switch fall-through
  i2c: sh_mobile: use core to detect 'no zero length read' quirk
  i2c: xlr: use core to detect 'no zero length' quirk
  i2c: rcar: use core to detect 'no zero length' quirk
  i2c: stu300: use core to detect 'no zero length' quirk
  i2c: pmcmsp: use core to detect 'no zero length' quirk
  i2c: mxs: use core to detect 'no zero length' quirk
  ...

46 files changed, 2616 insertions, 620 deletions

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 4f8df2ec87b1..451d4ae50e66 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -116,24 +116,21 @@ config I2C_I801
 	    DH89xxCC (PCH)
 	    Panther Point (PCH)
 	    Lynx Point (PCH)
-	    Lynx Point-LP (PCH)
 	    Avoton (SOC)
 	    Wellsburg (PCH)
 	    Coleto Creek (PCH)
 	    Wildcat Point (PCH)
-	    Wildcat Point-LP (PCH)
 	    BayTrail (SOC)
 	    Braswell (SOC)
-	    Sunrise Point-H (PCH)
-	    Sunrise Point-LP (PCH)
-	    Kaby Lake-H (PCH)
+	    Sunrise Point (PCH)
+	    Kaby Lake (PCH)
 	    DNV (SOC)
 	    Broxton (SOC)
 	    Lewisburg (PCH)
 	    Gemini Lake (SOC)
-	    Cannon Lake-H (PCH)
-	    Cannon Lake-LP (PCH)
+	    Cannon Lake (PCH)
 	    Cedar Fork (PCH)
+	    Ice Lake (PCH)
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-i801.
@@ -762,6 +759,13 @@ config I2C_OMAP
 	  Like OMAP1510/1610/1710/5912 and OMAP242x.
 	  For details see http://www.ti.com/omap.
 
+config I2C_OWL
+	tristate "Actions Semiconductor Owl I2C Controller"
+	depends on ARCH_ACTIONS || COMPILE_TEST
+	help
+	  Say Y here if you want to use the I2C bus controller on
+	  the Actions Semiconductor Owl SoC's.
+
 config I2C_PASEMI
 	tristate "PA Semi SMBus interface"
 	depends on PPC_PASEMI && PCI
@@ -828,6 +832,19 @@ config I2C_PXA_SLAVE
 	  is necessary for systems where the PXA may be a target on the
 	  I2C bus.
 
+config I2C_QCOM_GENI
+	tristate "Qualcomm Technologies Inc.'s GENI based I2C controller"
+	depends on ARCH_QCOM || COMPILE_TEST
+	depends on QCOM_GENI_SE
+	help
+	  This driver supports GENI serial engine based I2C controller in
+	  master mode on the Qualcomm Technologies Inc.'s SoCs. If you say
+	  yes to this option, support will be included for the built-in I2C
+	  interface on the Qualcomm Technologies Inc.'s SoCs.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-qcom-geni.
+
 config I2C_QUP
 	tristate "Qualcomm QUP based I2C controller"
 	depends on ARCH_QCOM
@@ -1330,4 +1347,15 @@ config I2C_ZX2967
 	  This driver can also be built as a module. If so, the module will be
 	  called i2c-zx2967.
 
+config I2C_FSI
+	tristate "FSI I2C driver"
+	depends on FSI
+	help
+	  Driver for FSI bus attached I2C masters. These are I2C masters that
+	  are connected to the system over an FSI bus, instead of the more
+	  common PCI or MMIO interface.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called as i2c-fsi.
+
 endmenu
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 5a869144a0c5..18b26af82b1c 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -76,6 +76,7 @@ obj-$(CONFIG_I2C_MXS)		+= i2c-mxs.o
 obj-$(CONFIG_I2C_NOMADIK)	+= i2c-nomadik.o
 obj-$(CONFIG_I2C_OCORES)	+= i2c-ocores.o
 obj-$(CONFIG_I2C_OMAP)		+= i2c-omap.o
+obj-$(CONFIG_I2C_OWL)		+= i2c-owl.o
 obj-$(CONFIG_I2C_PASEMI)	+= i2c-pasemi.o
 obj-$(CONFIG_I2C_PCA_PLATFORM)	+= i2c-pca-platform.o
 obj-$(CONFIG_I2C_PMCMSP)	+= i2c-pmcmsp.o
@@ -83,6 +84,7 @@ obj-$(CONFIG_I2C_PNX)		+= i2c-pnx.o
 obj-$(CONFIG_I2C_PUV3)		+= i2c-puv3.o
 obj-$(CONFIG_I2C_PXA)		+= i2c-pxa.o
 obj-$(CONFIG_I2C_PXA_PCI)	+= i2c-pxa-pci.o
+obj-$(CONFIG_I2C_QCOM_GENI)	+= i2c-qcom-geni.o
 obj-$(CONFIG_I2C_QUP)		+= i2c-qup.o
 obj-$(CONFIG_I2C_RIIC)		+= i2c-riic.o
 obj-$(CONFIG_I2C_RK3X)		+= i2c-rk3x.o
@@ -137,5 +139,6 @@ obj-$(CONFIG_I2C_PCA_ISA)	+= i2c-pca-isa.o
 obj-$(CONFIG_I2C_SIBYTE)	+= i2c-sibyte.o
 obj-$(CONFIG_I2C_XGENE_SLIMPRO) += i2c-xgene-slimpro.o
 obj-$(CONFIG_SCx200_ACB)	+= scx200_acb.o
+obj-$(CONFIG_I2C_FSI)		+= i2c-fsi.o
 
 ccflags-$(CONFIG_I2C_DEBUG_BUS) := -DDEBUG
diff --git a/drivers/i2c/busses/i2c-amd8111.c b/drivers/i2c/busses/i2c-amd8111.c
index 95a80a8f81b5..134567f3019f 100644
--- a/drivers/i2c/busses/i2c-amd8111.c
+++ b/drivers/i2c/busses/i2c-amd8111.c
@@ -384,6 +384,7 @@ static s32 amd8111_access(struct i2c_adapter * adap, u16 addr,
 			if (status)
 				return status;
 			len = min_t(u8, len, I2C_SMBUS_BLOCK_MAX);
+			/* fall through */
 		case I2C_SMBUS_I2C_BLOCK_DATA:
 			for (i = 0; i < len; i++) {
 				status = amd_ec_read(smbus, AMD_SMB_DATA + i,
diff --git a/drivers/i2c/busses/i2c-aspeed.c b/drivers/i2c/busses/i2c-aspeed.c
index 60e4d0e939a3..a4f956c6d567 100644
--- a/drivers/i2c/busses/i2c-aspeed.c
+++ b/drivers/i2c/busses/i2c-aspeed.c
@@ -111,22 +111,22 @@
 #define ASPEED_I2CD_DEV_ADDR_MASK			GENMASK(6, 0)
 
 enum aspeed_i2c_master_state {
+	ASPEED_I2C_MASTER_INACTIVE,
 	ASPEED_I2C_MASTER_START,
 	ASPEED_I2C_MASTER_TX_FIRST,
 	ASPEED_I2C_MASTER_TX,
 	ASPEED_I2C_MASTER_RX_FIRST,
 	ASPEED_I2C_MASTER_RX,
 	ASPEED_I2C_MASTER_STOP,
-	ASPEED_I2C_MASTER_INACTIVE,
 };
 
 enum aspeed_i2c_slave_state {
+	ASPEED_I2C_SLAVE_STOP,
 	ASPEED_I2C_SLAVE_START,
 	ASPEED_I2C_SLAVE_READ_REQUESTED,
 	ASPEED_I2C_SLAVE_READ_PROCESSED,
 	ASPEED_I2C_SLAVE_WRITE_REQUESTED,
 	ASPEED_I2C_SLAVE_WRITE_RECEIVED,
-	ASPEED_I2C_SLAVE_STOP,
 };
 
 struct aspeed_i2c_bus {
@@ -234,7 +234,6 @@ static bool aspeed_i2c_slave_irq(struct aspeed_i2c_bus *bus)
 	bool irq_handled = true;
 	u8 value;
 
-	spin_lock(&bus->lock);
 	if (!slave) {
 		irq_handled = false;
 		goto out;
@@ -325,7 +324,6 @@ static bool aspeed_i2c_slave_irq(struct aspeed_i2c_bus *bus)
 	writel(status_ack, bus->base + ASPEED_I2C_INTR_STS_REG);
 
 out:
-	spin_unlock(&bus->lock);
 	return irq_handled;
 }
 #endif /* CONFIG_I2C_SLAVE */
@@ -389,7 +387,6 @@ static bool aspeed_i2c_master_irq(struct aspeed_i2c_bus *bus)
 	u8 recv_byte;
 	int ret;
 
-	spin_lock(&bus->lock);
 	irq_status = readl(bus->base + ASPEED_I2C_INTR_STS_REG);
 	/* Ack all interrupt bits. */
 	writel(irq_status, bus->base + ASPEED_I2C_INTR_STS_REG);
@@ -407,7 +404,7 @@ static bool aspeed_i2c_master_irq(struct aspeed_i2c_bus *bus)
 	 */
 	ret = aspeed_i2c_is_irq_error(irq_status);
 	if (ret < 0) {
-		dev_dbg(bus->dev, "received error interrupt: 0x%08x",
+		dev_dbg(bus->dev, "received error interrupt: 0x%08x\n",
 			irq_status);
 		bus->cmd_err = ret;
 		bus->master_state = ASPEED_I2C_MASTER_INACTIVE;
@@ -416,7 +413,7 @@ static bool aspeed_i2c_master_irq(struct aspeed_i2c_bus *bus)
 
 	/* We are in an invalid state; reset bus to a known state. */
 	if (!bus->msgs) {
-		dev_err(bus->dev, "bus in unknown state");
+		dev_err(bus->dev, "bus in unknown state\n");
 		bus->cmd_err = -EIO;
 		if (bus->master_state != ASPEED_I2C_MASTER_STOP)
 			aspeed_i2c_do_stop(bus);
@@ -431,7 +428,7 @@ static bool aspeed_i2c_master_irq(struct aspeed_i2c_bus *bus)
 	 */
 	if (bus->master_state == ASPEED_I2C_MASTER_START) {
 		if (unlikely(!(irq_status & ASPEED_I2CD_INTR_TX_ACK))) {
-			pr_devel("no slave present at %02x", msg->addr);
+			pr_devel("no slave present at %02x\n", msg->addr);
 			status_ack |= ASPEED_I2CD_INTR_TX_NAK;
 			bus->cmd_err = -ENXIO;
 			aspeed_i2c_do_stop(bus);
@@ -451,11 +448,11 @@ static bool aspeed_i2c_master_irq(struct aspeed_i2c_bus *bus)
 	switch (bus->master_state) {
 	case ASPEED_I2C_MASTER_TX:
 		if (unlikely(irq_status & ASPEED_I2CD_INTR_TX_NAK)) {
-			dev_dbg(bus->dev, "slave NACKed TX");
+			dev_dbg(bus->dev, "slave NACKed TX\n");
 			status_ack |= ASPEED_I2CD_INTR_TX_NAK;
 			goto error_and_stop;
 		} else if (unlikely(!(irq_status & ASPEED_I2CD_INTR_TX_ACK))) {
-			dev_err(bus->dev, "slave failed to ACK TX");
+			dev_err(bus->dev, "slave failed to ACK TX\n");
 			goto error_and_stop;
 		}
 		status_ack |= ASPEED_I2CD_INTR_TX_ACK;
@@ -478,7 +475,7 @@ static bool aspeed_i2c_master_irq(struct aspeed_i2c_bus *bus)
 		/* fallthrough intended */
 	case ASPEED_I2C_MASTER_RX:
 		if (unlikely(!(irq_status & ASPEED_I2CD_INTR_RX_DONE))) {
-			dev_err(bus->dev, "master failed to RX");
+			dev_err(bus->dev, "master failed to RX\n");
 			goto error_and_stop;
 		}
 		status_ack |= ASPEED_I2CD_INTR_RX_DONE;
@@ -509,7 +506,7 @@ static bool aspeed_i2c_master_irq(struct aspeed_i2c_bus *bus)
 		goto out_no_complete;
 	case ASPEED_I2C_MASTER_STOP:
 		if (unlikely(!(irq_status & ASPEED_I2CD_INTR_NORMAL_STOP))) {
-			dev_err(bus->dev, "master failed to STOP");
+			dev_err(bus->dev, "master failed to STOP\n");
 			bus->cmd_err = -EIO;
 			/* Do not STOP as we have already tried. */
 		} else {
@@ -520,7 +517,7 @@ static bool aspeed_i2c_master_irq(struct aspeed_i2c_bus *bus)
 		goto out_complete;
 	case ASPEED_I2C_MASTER_INACTIVE:
 		dev_err(bus->dev,
-			"master received interrupt 0x%08x, but is inactive",
+			"master received interrupt 0x%08x, but is inactive\n",
 			irq_status);
 		bus->cmd_err = -EIO;
 		/* Do not STOP as we should be inactive. */
@@ -547,22 +544,29 @@ out_no_complete:
 		dev_err(bus->dev,
 			"irq handled != irq. expected 0x%08x, but was 0x%08x\n",
 			irq_status, status_ack);
-	spin_unlock(&bus->lock);
 	return !!irq_status;
 }
 
 static irqreturn_t aspeed_i2c_bus_irq(int irq, void *dev_id)
 {
 	struct aspeed_i2c_bus *bus = dev_id;
+	bool ret;
+
+	spin_lock(&bus->lock);
 
 #if IS_ENABLED(CONFIG_I2C_SLAVE)
 	if (aspeed_i2c_slave_irq(bus)) {
 		dev_dbg(bus->dev, "irq handled by slave.\n");
-		return IRQ_HANDLED;
+		ret = true;
+		goto out;
 	}
 #endif /* CONFIG_I2C_SLAVE */
 
-	return aspeed_i2c_master_irq(bus) ? IRQ_HANDLED : IRQ_NONE;
+	ret = aspeed_i2c_master_irq(bus);
+
+out:
+	spin_unlock(&bus->lock);
+	return ret ? IRQ_HANDLED : IRQ_NONE;
 }
 
 static int aspeed_i2c_master_xfer(struct i2c_adapter *adap,
@@ -851,7 +855,7 @@ static int aspeed_i2c_probe_bus(struct platform_device *pdev)
 	bus->rst = devm_reset_control_get_shared(&pdev->dev, NULL);
 	if (IS_ERR(bus->rst)) {
 		dev_err(&pdev->dev,
-			"missing or invalid reset controller device tree entry");
+			"missing or invalid reset controller device tree entry\n");
 		return PTR_ERR(bus->rst);
 	}
 	reset_control_deassert(bus->rst);
@@ -868,7 +872,7 @@ static int aspeed_i2c_probe_bus(struct platform_device *pdev)
 	if (!match)
 		bus->get_clk_reg_val = aspeed_i2c_24xx_get_clk_reg_val;
 	else
-		bus->get_clk_reg_val = match->data;
+		bus->get_clk_reg_val = (u32 (*)(u32))match->data;
 
 	/* Initialize the I2C adapter */
 	spin_lock_init(&bus->lock);
diff --git a/drivers/i2c/busses/i2c-brcmstb.c b/drivers/i2c/busses/i2c-brcmstb.c
index 78792b4d6437..826d32049996 100644
--- a/drivers/i2c/busses/i2c-brcmstb.c
+++ b/drivers/i2c/busses/i2c-brcmstb.c
@@ -689,9 +689,9 @@ static int brcmstb_i2c_suspend(struct device *dev)
 {
 	struct brcmstb_i2c_dev *i2c_dev = dev_get_drvdata(dev);
 
-	i2c_lock_adapter(&i2c_dev->adapter);
+	i2c_lock_bus(&i2c_dev->adapter, I2C_LOCK_ROOT_ADAPTER);
 	i2c_dev->is_suspended = true;
-	i2c_unlock_adapter(&i2c_dev->adapter);
+	i2c_unlock_bus(&i2c_dev->adapter, I2C_LOCK_ROOT_ADAPTER);
 
 	return 0;
 }
@@ -700,10 +700,10 @@ static int brcmstb_i2c_resume(struct device *dev)
 {
 	struct brcmstb_i2c_dev *i2c_dev = dev_get_drvdata(dev);
 
-	i2c_lock_adapter(&i2c_dev->adapter);
+	i2c_lock_bus(&i2c_dev->adapter, I2C_LOCK_ROOT_ADAPTER);
 	brcmstb_i2c_set_bsc_reg_defaults(i2c_dev);
 	i2c_dev->is_suspended = false;
-	i2c_unlock_adapter(&i2c_dev->adapter);
+	i2c_unlock_bus(&i2c_dev->adapter, I2C_LOCK_ROOT_ADAPTER);
 
 	return 0;
 }
diff --git a/drivers/i2c/busses/i2c-davinci.c b/drivers/i2c/busses/i2c-davinci.c
index 7379043711df..11caafa0e050 100644
--- a/drivers/i2c/busses/i2c-davinci.c
+++ b/drivers/i2c/busses/i2c-davinci.c
@@ -718,14 +718,14 @@ static int i2c_davinci_cpufreq_transition(struct notifier_block *nb,
 
 	dev = container_of(nb, struct davinci_i2c_dev, freq_transition);
 
-	i2c_lock_adapter(&dev->adapter);
+	i2c_lock_bus(&dev->adapter, I2C_LOCK_ROOT_ADAPTER);
 	if (val == CPUFREQ_PRECHANGE) {
 		davinci_i2c_reset_ctrl(dev, 0);
 	} else if (val == CPUFREQ_POSTCHANGE) {
 		i2c_davinci_calc_clk_dividers(dev);
 		davinci_i2c_reset_ctrl(dev, 1);
 	}
-	i2c_unlock_adapter(&dev->adapter);
+	i2c_unlock_bus(&dev->adapter, I2C_LOCK_ROOT_ADAPTER);
 
 	return 0;
 }
diff --git a/drivers/i2c/busses/i2c-designware-baytrail.c b/drivers/i2c/busses/i2c-designware-baytrail.c
index dbda8c9c8a1c..a2a275cfc1f6 100644
--- a/drivers/i2c/busses/i2c-designware-baytrail.c
+++ b/drivers/i2c/busses/i2c-designware-baytrail.c
@@ -1,15 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Intel BayTrail PMIC I2C bus semaphore implementaion
  * Copyright (c) 2014, Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
- * more details.
  */
 #include <linux/delay.h>
 #include <linux/device.h>
diff --git a/drivers/i2c/busses/i2c-designware-common.c b/drivers/i2c/busses/i2c-designware-common.c
index 48914dfc8ce8..69ec4a791f23 100644
--- a/drivers/i2c/busses/i2c-designware-common.c
+++ b/drivers/i2c/busses/i2c-designware-common.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
 /*
  * Synopsys DesignWare I2C adapter driver.
  *
@@ -6,20 +7,6 @@
  * Copyright (C) 2006 Texas Instruments.
  * Copyright (C) 2007 MontaVista Software Inc.
  * Copyright (C) 2009 Provigent Ltd.
- *
- * ----------------------------------------------------------------------------
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- * ----------------------------------------------------------------------------
- *
  */
 #include <linux/clk.h>
 #include <linux/delay.h>
@@ -31,6 +18,7 @@
 #include <linux/io.h>
 #include <linux/module.h>
 #include <linux/pm_runtime.h>
+#include <linux/swab.h>
 
 #include "i2c-designware-core.h"
 
@@ -94,6 +82,40 @@ void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset)
 	}
 }
 
+/**
+ * i2c_dw_set_reg_access() - Set register access flags
+ * @dev: device private data
+ *
+ * Autodetects needed register access mode and sets access flags accordingly.
+ * This must be called before doing any other register access.
+ */
+int i2c_dw_set_reg_access(struct dw_i2c_dev *dev)
+{
+	u32 reg;
+	int ret;
+
+	ret = i2c_dw_acquire_lock(dev);
+	if (ret)
+		return ret;
+
+	reg = dw_readl(dev, DW_IC_COMP_TYPE);
+	i2c_dw_release_lock(dev);
+
+	if (reg == swab32(DW_IC_COMP_TYPE_VALUE)) {
+		/* Configure register endianess access */
+		dev->flags |= ACCESS_SWAP;
+	} else if (reg == (DW_IC_COMP_TYPE_VALUE & 0x0000ffff)) {
+		/* Configure register access mode 16bit */
+		dev->flags |= ACCESS_16BIT;
+	} else if (reg != DW_IC_COMP_TYPE_VALUE) {
+		dev_err(dev->dev,
+			"Unknown Synopsys component type: 0x%08x\n", reg);
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
 u32 i2c_dw_scl_hcnt(u32 ic_clk, u32 tSYMBOL, u32 tf, int cond, int offset)
 {
 	/*
@@ -149,6 +171,47 @@ u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset)
 	return ((ic_clk * (tLOW + tf) + 500000) / 1000000) - 1 + offset;
 }
 
+int i2c_dw_set_sda_hold(struct dw_i2c_dev *dev)
+{
+	u32 reg;
+	int ret;
+
+	ret = i2c_dw_acquire_lock(dev);
+	if (ret)
+		return ret;
+
+	/* Configure SDA Hold Time if required */
+	reg = dw_readl(dev, DW_IC_COMP_VERSION);
+	if (reg >= DW_IC_SDA_HOLD_MIN_VERS) {
+		if (!dev->sda_hold_time) {
+			/* Keep previous hold time setting if no one set it */
+			dev->sda_hold_time = dw_readl(dev, DW_IC_SDA_HOLD);
+		}
+
+		/*
+		 * Workaround for avoiding TX arbitration lost in case I2C
+		 * slave pulls SDA down "too quickly" after falling egde of
+		 * SCL by enabling non-zero SDA RX hold. Specification says it
+		 * extends incoming SDA low to high transition while SCL is
+		 * high but it apprears to help also above issue.
+		 */
+		if (!(dev->sda_hold_time & DW_IC_SDA_HOLD_RX_MASK))
+			dev->sda_hold_time |= 1 << DW_IC_SDA_HOLD_RX_SHIFT;
+
+		dev_dbg(dev->dev, "SDA Hold Time TX:RX = %d:%d\n",
+			dev->sda_hold_time & ~(u32)DW_IC_SDA_HOLD_RX_MASK,
+			dev->sda_hold_time >> DW_IC_SDA_HOLD_RX_SHIFT);
+	} else if (dev->sda_hold_time) {
+		dev_warn(dev->dev,
+			"Hardware too old to adjust SDA hold time.\n");
+		dev->sda_hold_time = 0;
+	}
+
+	i2c_dw_release_lock(dev);
+
+	return 0;
+}
+
 void __i2c_dw_disable(struct dw_i2c_dev *dev)
 {
 	int timeout = 100;
diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h
index d690e648bc01..e367b1af4ab2 100644
--- a/drivers/i2c/busses/i2c-designware-core.h
+++ b/drivers/i2c/busses/i2c-designware-core.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
 /*
  * Synopsys DesignWare I2C adapter driver.
  *
@@ -6,20 +7,6 @@
  * Copyright (C) 2006 Texas Instruments.
  * Copyright (C) 2007 MontaVista Software Inc.
  * Copyright (C) 2009 Provigent Ltd.
- *
- * ----------------------------------------------------------------------------
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- * ----------------------------------------------------------------------------
- *
  */
 
 #include <linux/i2c.h>
@@ -212,7 +199,8 @@
  * @tx_fifo_depth: depth of the hardware tx fifo
  * @rx_fifo_depth: depth of the hardware rx fifo
  * @rx_outstanding: current master-rx elements in tx fifo
- * @clk_freq: bus clock frequency
+ * @timings: bus clock frequency, SDA hold and other timings
+ * @sda_hold_time: SDA hold value
  * @ss_hcnt: standard speed HCNT value
  * @ss_lcnt: standard speed LCNT value
  * @fs_hcnt: fast speed HCNT value
@@ -264,10 +252,8 @@ struct dw_i2c_dev {
 	unsigned int		tx_fifo_depth;
 	unsigned int		rx_fifo_depth;
 	int			rx_outstanding;
-	u32			clk_freq;
+	struct i2c_timings	timings;
 	u32			sda_hold_time;
-	u32			sda_falling_time;
-	u32			scl_falling_time;
 	u16			ss_hcnt;
 	u16			ss_lcnt;
 	u16			fs_hcnt;
@@ -295,8 +281,10 @@ struct dw_i2c_dev {
 
 u32 dw_readl(struct dw_i2c_dev *dev, int offset);
 void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset);
+int i2c_dw_set_reg_access(struct dw_i2c_dev *dev);
 u32 i2c_dw_scl_hcnt(u32 ic_clk, u32 tSYMBOL, u32 tf, int cond, int offset);
 u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset);
+int i2c_dw_set_sda_hold(struct dw_i2c_dev *dev);
 unsigned long i2c_dw_clk_rate(struct dw_i2c_dev *dev);
 int i2c_dw_prepare_clk(struct dw_i2c_dev *dev, bool prepare);
 int i2c_dw_acquire_lock(struct dw_i2c_dev *dev);
diff --git a/drivers/i2c/busses/i2c-designware-master.c b/drivers/i2c/busses/i2c-designware-master.c
index 27436a937492..e18442b9973a 100644
--- a/drivers/i2c/busses/i2c-designware-master.c
+++ b/drivers/i2c/busses/i2c-designware-master.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
 /*
  * Synopsys DesignWare I2C adapter driver (master only).
  *
@@ -6,20 +7,6 @@
  * Copyright (C) 2006 Texas Instruments.
  * Copyright (C) 2007 MontaVista Software Inc.
  * Copyright (C) 2009 Provigent Ltd.
- *
- * ----------------------------------------------------------------------------
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- * ----------------------------------------------------------------------------
- *
  */
 #include <linux/delay.h>
 #include <linux/err.h>
@@ -45,90 +32,79 @@ static void i2c_dw_configure_fifo_master(struct dw_i2c_dev *dev)
 	dw_writel(dev, dev->master_cfg, DW_IC_CON);
 }
 
-/**
- * i2c_dw_init() - Initialize the designware I2C master hardware
- * @dev: device private data
- *
- * This functions configures and enables the I2C master.
- * This function is called during I2C init function, and in case of timeout at
- * run time.
- */
-static int i2c_dw_init_master(struct dw_i2c_dev *dev)
+static int i2c_dw_set_timings_master(struct dw_i2c_dev *dev)
 {
-	u32 hcnt, lcnt;
-	u32 reg, comp_param1;
+	u32 ic_clk = i2c_dw_clk_rate(dev);
+	const char *mode_str, *fp_str = "";
+	u32 comp_param1;
 	u32 sda_falling_time, scl_falling_time;
+	struct i2c_timings *t = &dev->timings;
 	int ret;
 
 	ret = i2c_dw_acquire_lock(dev);
 	if (ret)
 		return ret;
-
-	reg = dw_readl(dev, DW_IC_COMP_TYPE);
-	if (reg == ___constant_swab32(DW_IC_COMP_TYPE_VALUE)) {
-		/* Configure register endianess access */
-		dev->flags |= ACCESS_SWAP;
-	} else if (reg == (DW_IC_COMP_TYPE_VALUE & 0x0000ffff)) {
-		/* Configure register access mode 16bit */
-		dev->flags |= ACCESS_16BIT;
-	} else if (reg != DW_IC_COMP_TYPE_VALUE) {
-		dev_err(dev->dev,
-			"Unknown Synopsys component type: 0x%08x\n", reg);
-		i2c_dw_release_lock(dev);
-		return -ENODEV;
-	}
-
 	comp_param1 = dw_readl(dev, DW_IC_COMP_PARAM_1);
+	i2c_dw_release_lock(dev);
 
-	/* Disable the adapter */
-	__i2c_dw_disable(dev);
-
-	/* Set standard and fast speed deviders for high/low periods */
-
-	sda_falling_time = dev->sda_falling_time ?: 300; /* ns */
-	scl_falling_time = dev->scl_falling_time ?: 300; /* ns */
+	/* Set standard and fast speed dividers for high/low periods */
+	sda_falling_time = t->sda_fall_ns ?: 300; /* ns */
+	scl_falling_time = t->scl_fall_ns ?: 300; /* ns */
 
-	/* Set SCL timing parameters for standard-mode */
-	if (dev->ss_hcnt && dev->ss_lcnt) {
-		hcnt = dev->ss_hcnt;
-		lcnt = dev->ss_lcnt;
-	} else {
-		hcnt = i2c_dw_scl_hcnt(i2c_dw_clk_rate(dev),
+	/* Calculate SCL timing parameters for standard mode if not set */
+	if (!dev->ss_hcnt || !dev->ss_lcnt) {
+		dev->ss_hcnt =
+			i2c_dw_scl_hcnt(ic_clk,
 					4000,	/* tHD;STA = tHIGH = 4.0 us */
 					sda_falling_time,
 					0,	/* 0: DW default, 1: Ideal */
 					0);	/* No offset */
-		lcnt = i2c_dw_scl_lcnt(i2c_dw_clk_rate(dev),
+		dev->ss_lcnt =
+			i2c_dw_scl_lcnt(ic_clk,
 					4700,	/* tLOW = 4.7 us */
 					scl_falling_time,
 					0);	/* No offset */
 	}
-	dw_writel(dev, hcnt, DW_IC_SS_SCL_HCNT);
-	dw_writel(dev, lcnt, DW_IC_SS_SCL_LCNT);
-	dev_dbg(dev->dev, "Standard-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt);
-
-	/* Set SCL timing parameters for fast-mode or fast-mode plus */
-	if ((dev->clk_freq == 1000000) && dev->fp_hcnt && dev->fp_lcnt) {
-		hcnt = dev->fp_hcnt;
-		lcnt = dev->fp_lcnt;
-	} else if (dev->fs_hcnt && dev->fs_lcnt) {
-		hcnt = dev->fs_hcnt;
-		lcnt = dev->fs_lcnt;
-	} else {
-		hcnt = i2c_dw_scl_hcnt(i2c_dw_clk_rate(dev),
+	dev_dbg(dev->dev, "Standard Mode HCNT:LCNT = %d:%d\n",
+		dev->ss_hcnt, dev->ss_lcnt);
+
+	/*
+	 * Set SCL timing parameters for fast mode or fast mode plus. Only
+	 * difference is the timing parameter values since the registers are
+	 * the same.
+	 */
+	if (t->bus_freq_hz == 1000000) {
+		/*
+		 * Check are fast mode plus parameters available and use
+		 * fast mode if not.
+		 */
+		if (dev->fp_hcnt && dev->fp_lcnt) {
+			dev->fs_hcnt = dev->fp_hcnt;
+			dev->fs_lcnt = dev->fp_lcnt;
+			fp_str = " Plus";
+		}
+	}
+	/*
+	 * Calculate SCL timing parameters for fast mode if not set. They are
+	 * needed also in high speed mode.
+	 */
+	if (!dev->fs_hcnt || !dev->fs_lcnt) {
+		dev->fs_hcnt =
+			i2c_dw_scl_hcnt(ic_clk,
 					600,	/* tHD;STA = tHIGH = 0.6 us */
 					sda_falling_time,
 					0,	/* 0: DW default, 1: Ideal */
 					0);	/* No offset */
-		lcnt = i2c_dw_scl_lcnt(i2c_dw_clk_rate(dev),
+		dev->fs_lcnt =
+			i2c_dw_scl_lcnt(ic_clk,
 					1300,	/* tLOW = 1.3 us */
 					scl_falling_time,
 					0);	/* No offset */
 	}
-	dw_writel(dev, hcnt, DW_IC_FS_SCL_HCNT);
-	dw_writel(dev, lcnt, DW_IC_FS_SCL_LCNT);
-	dev_dbg(dev->dev, "Fast-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt);
+	dev_dbg(dev->dev, "Fast Mode%s HCNT:LCNT = %d:%d\n",
+		fp_str, dev->fs_hcnt, dev->fs_lcnt);
 
+	/* Check is high speed possible and fall back to fast mode if not */
 	if ((dev->master_cfg & DW_IC_CON_SPEED_MASK) ==
 		DW_IC_CON_SPEED_HIGH) {
 		if ((comp_param1 & DW_IC_COMP_PARAM_1_SPEED_MODE_MASK)
@@ -136,37 +112,70 @@ static int i2c_dw_init_master(struct dw_i2c_dev *dev)
 			dev_err(dev->dev, "High Speed not supported!\n");
 			dev->master_cfg &= ~DW_IC_CON_SPEED_MASK;
 			dev->master_cfg |= DW_IC_CON_SPEED_FAST;
+			dev->hs_hcnt = 0;
+			dev->hs_lcnt = 0;
 		} else if (dev->hs_hcnt && dev->hs_lcnt) {
-			hcnt = dev->hs_hcnt;
-			lcnt = dev->hs_lcnt;
-			dw_writel(dev, hcnt, DW_IC_HS_SCL_HCNT);
-			dw_writel(dev, lcnt, DW_IC_HS_SCL_LCNT);
-			dev_dbg(dev->dev, "HighSpeed-mode HCNT:LCNT = %d:%d\n",
-				hcnt, lcnt);
+			dev_dbg(dev->dev, "High Speed Mode HCNT:LCNT = %d:%d\n",
+				dev->hs_hcnt, dev->hs_lcnt);
 		}
 	}
 
-	/* Configure SDA Hold Time if required */
-	reg = dw_readl(dev, DW_IC_COMP_VERSION);
-	if (reg >= DW_IC_SDA_HOLD_MIN_VERS) {
-		if (!dev->sda_hold_time) {
-			/* Keep previous hold time setting if no one set it */
-			dev->sda_hold_time = dw_readl(dev, DW_IC_SDA_HOLD);
-		}
-		/*
-		 * Workaround for avoiding TX arbitration lost in case I2C
-		 * slave pulls SDA down "too quickly" after falling egde of
-		 * SCL by enabling non-zero SDA RX hold. Specification says it
-		 * extends incoming SDA low to high transition while SCL is
-		 * high but it apprears to help also above issue.
-		 */
-		if (!(dev->sda_hold_time & DW_IC_SDA_HOLD_RX_MASK))
-			dev->sda_hold_time |= 1 << DW_IC_SDA_HOLD_RX_SHIFT;
-		dw_writel(dev, dev->sda_hold_time, DW_IC_SDA_HOLD);
-	} else if (dev->sda_hold_time) {
-		dev_warn(dev->dev,
-			"Hardware too old to adjust SDA hold time.\n");
+	ret = i2c_dw_set_sda_hold(dev);
+	if (ret)
+		goto out;
+
+	switch (dev->master_cfg & DW_IC_CON_SPEED_MASK) {
+	case DW_IC_CON_SPEED_STD:
+		mode_str = "Standard Mode";
+		break;
+	case DW_IC_CON_SPEED_HIGH:
+		mode_str = "High Speed Mode";
+		break;
+	default:
+		mode_str = "Fast Mode";
 	}
+	dev_dbg(dev->dev, "Bus speed: %s%s\n", mode_str, fp_str);
+
+out:
+	return ret;
+}
+
+/**
+ * i2c_dw_init() - Initialize the designware I2C master hardware
+ * @dev: device private data
+ *
+ * This functions configures and enables the I2C master.
+ * This function is called during I2C init function, and in case of timeout at
+ * run time.
+ */
+static int i2c_dw_init_master(struct dw_i2c_dev *dev)
+{
+	int ret;
+
+	ret = i2c_dw_acquire_lock(dev);
+	if (ret)
+		return ret;
+
+	/* Disable the adapter */
+	__i2c_dw_disable(dev);
+
+	/* Write standard speed timing parameters */
+	dw_writel(dev, dev->ss_hcnt, DW_IC_SS_SCL_HCNT);
+	dw_writel(dev, dev->ss_lcnt, DW_IC_SS_SCL_LCNT);
+
+	/* Write fast mode/fast mode plus timing parameters */
+	dw_writel(dev, dev->fs_hcnt, DW_IC_FS_SCL_HCNT);
+	dw_writel(dev, dev->fs_lcnt, DW_IC_FS_SCL_LCNT);
+
+	/* Write high speed timing parameters if supported */
+	if (dev->hs_hcnt && dev->hs_lcnt) {
+		dw_writel(dev, dev->hs_hcnt, DW_IC_HS_SCL_HCNT);
+		dw_writel(dev, dev->hs_lcnt, DW_IC_HS_SCL_LCNT);
+	}
+
+	/* Write SDA hold time if supported */
+	if (dev->sda_hold_time)
+		dw_writel(dev, dev->sda_hold_time, DW_IC_SDA_HOLD);
 
 	i2c_dw_configure_fifo_master(dev);
 	i2c_dw_release_lock(dev);
@@ -253,13 +262,6 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev)
 			break;
 		}
 
-		if (msgs[dev->msg_write_idx].len == 0) {
-			dev_err(dev->dev,
-				"%s: invalid message length\n", __func__);
-			dev->msg_err = -EINVAL;
-			break;
-		}
-
 		if (!(dev->status & STATUS_WRITE_IN_PROGRESS)) {
 			/* new i2c_msg */
 			buf = msgs[dev->msg_write_idx].buf;
@@ -502,6 +504,10 @@ static const struct i2c_algorithm i2c_dw_algo = {
 	.functionality = i2c_dw_func,
 };
 
+static const struct i2c_adapter_quirks i2c_dw_quirks = {
+	.flags = I2C_AQ_NO_ZERO_LEN,
+};
+
 static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev)
 {
 	u32 stat;
@@ -681,6 +687,14 @@ int i2c_dw_probe(struct dw_i2c_dev *dev)
 	dev->disable = i2c_dw_disable;
 	dev->disable_int = i2c_dw_disable_int;
 
+	ret = i2c_dw_set_reg_access(dev);
+	if (ret)
+		return ret;
+
+	ret = i2c_dw_set_timings_master(dev);
+	if (ret)
+		return ret;
+
 	ret = dev->init(dev);
 	if (ret)
 		return ret;
@@ -689,6 +703,7 @@ int i2c_dw_probe(struct dw_i2c_dev *dev)
 		 "Synopsys DesignWare I2C adapter");
 	adap->retries = 3;
 	adap->algo = &i2c_dw_algo;
+	adap->quirks = &i2c_dw_quirks;
 	adap->dev.parent = dev->dev;
 	i2c_set_adapdata(adap, dev);
 
diff --git a/drivers/i2c/busses/i2c-designware-pcidrv.c b/drivers/i2c/busses/i2c-designware-pcidrv.c
index 86e1bd0b82e9..d50f80487214 100644
--- a/drivers/i2c/busses/i2c-designware-pcidrv.c
+++ b/drivers/i2c/busses/i2c-designware-pcidrv.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
 /*
  * Synopsys DesignWare I2C adapter driver (master only).
  *
@@ -7,22 +8,7 @@
  * Copyright (C) 2007 MontaVista Software Inc.
  * Copyright (C) 2009 Provigent Ltd.
  * Copyright (C) 2011, 2015, 2016 Intel Corporation.
- *
- * ----------------------------------------------------------------------------
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- * ----------------------------------------------------------------------------
- *
  */
-
 #include <linux/acpi.h>
 #include <linux/delay.h>
 #include <linux/err.h>
@@ -105,6 +91,7 @@ static int mfld_setup(struct pci_dev *pdev, struct dw_pci_controller *c)
 	case 0x0817:
 		c->bus_cfg &= ~DW_IC_CON_SPEED_MASK;
 		c->bus_cfg |= DW_IC_CON_SPEED_STD;
+		/* fall through */
 	case 0x0818:
 	case 0x0819:
 		c->bus_num = pdev->device - 0x817 + 3;
diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
index 5660daf6c92e..1a8d2da5b000 100644
--- a/drivers/i2c/busses/i2c-designware-platdrv.c
+++ b/drivers/i2c/busses/i2c-designware-platdrv.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
 /*
  * Synopsys DesignWare I2C adapter driver.
  *
@@ -6,20 +7,6 @@
  * Copyright (C) 2006 Texas Instruments.
  * Copyright (C) 2007 MontaVista Software Inc.
  * Copyright (C) 2009 Provigent Ltd.
- *
- * ----------------------------------------------------------------------------
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- * ----------------------------------------------------------------------------
- *
  */
 #include <linux/acpi.h>
 #include <linux/clk-provider.h>
@@ -96,6 +83,7 @@ static void dw_i2c_acpi_params(struct platform_device *pdev, char method[],
 static int dw_i2c_acpi_configure(struct platform_device *pdev)
 {
 	struct dw_i2c_dev *dev = platform_get_drvdata(pdev);
+	struct i2c_timings *t = &dev->timings;
 	u32 ss_ht = 0, fp_ht = 0, hs_ht = 0, fs_ht = 0;
 	acpi_handle handle = ACPI_HANDLE(&pdev->dev);
 	const struct acpi_device_id *id;
@@ -115,7 +103,7 @@ static int dw_i2c_acpi_configure(struct platform_device *pdev)
 	dw_i2c_acpi_params(pdev, "HSCN", &dev->hs_hcnt, &dev->hs_lcnt, &hs_ht);
 	dw_i2c_acpi_params(pdev, "FMCN", &dev->fs_hcnt, &dev->fs_lcnt, &fs_ht);
 
-	switch (dev->clk_freq) {
+	switch (t->bus_freq_hz) {
 	case 100000:
 		dev->sda_hold_time = ss_ht;
 		break;
@@ -175,6 +163,8 @@ static inline int dw_i2c_acpi_configure(struct platform_device *pdev)
 
 static void i2c_dw_configure_master(struct dw_i2c_dev *dev)
 {
+	struct i2c_timings *t = &dev->timings;
+
 	dev->functionality = I2C_FUNC_10BIT_ADDR | DW_IC_DEFAULT_FUNCTIONALITY;
 
 	dev->master_cfg = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE |
@@ -182,7 +172,7 @@ static void i2c_dw_configure_master(struct dw_i2c_dev *dev)
 
 	dev->mode = DW_IC_MASTER;
 
-	switch (dev->clk_freq) {
+	switch (t->bus_freq_hz) {
 	case 100000:
 		dev->master_cfg |= DW_IC_CON_SPEED_STD;
 		break;
@@ -240,7 +230,8 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 	struct dw_i2c_platform_data *pdata = dev_get_platdata(&pdev->dev);
 	struct i2c_adapter *adap;
 	struct dw_i2c_dev *dev;
-	u32 acpi_speed, ht = 0;
+	struct i2c_timings *t;
+	u32 acpi_speed;
 	struct resource *mem;
 	int i, irq, ret;
 	static const int supported_speeds[] = {
@@ -272,18 +263,11 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 		reset_control_deassert(dev->rst);
 	}
 
-	if (pdata) {
-		dev->clk_freq = pdata->i2c_scl_freq;
-	} else {
-		device_property_read_u32(&pdev->dev, "i2c-sda-hold-time-ns",
-					 &ht);
-		device_property_read_u32(&pdev->dev, "i2c-sda-falling-time-ns",
-					 &dev->sda_falling_time);
-		device_property_read_u32(&pdev->dev, "i2c-scl-falling-time-ns",
-					 &dev->scl_falling_time);
-		device_property_read_u32(&pdev->dev, "clock-frequency",
-					 &dev->clk_freq);
-	}
+	t = &dev->timings;
+	if (pdata)
+		t->bus_freq_hz = pdata->i2c_scl_freq;
+	else
+		i2c_parse_fw_timings(&pdev->dev, t, false);
 
 	acpi_speed = i2c_acpi_find_bus_speed(&pdev->dev);
 	/*
@@ -300,12 +284,12 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 	 * Find bus speed from the "clock-frequency" device property, ACPI
 	 * or by using fast mode if neither is set.
 	 */
-	if (acpi_speed && dev->clk_freq)
-		dev->clk_freq = min(dev->clk_freq, acpi_speed);
-	else if (acpi_speed || dev->clk_freq)
-		dev->clk_freq = max(dev->clk_freq, acpi_speed);
+	if (acpi_speed && t->bus_freq_hz)
+		t->bus_freq_hz = min(t->bus_freq_hz, acpi_speed);
+	else if (acpi_speed || t->bus_freq_hz)
+		t->bus_freq_hz = max(t->bus_freq_hz, acpi_speed);
 	else
-		dev->clk_freq = 400000;
+		t->bus_freq_hz = 400000;
 
 	if (has_acpi_companion(&pdev->dev))
 		dw_i2c_acpi_configure(pdev);
@@ -314,11 +298,11 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 	 * Only standard mode at 100kHz, fast mode at 400kHz,
 	 * fast mode plus at 1MHz and high speed mode at 3.4MHz are supported.
 	 */
-	if (dev->clk_freq != 100000 && dev->clk_freq != 400000
-	    && dev->clk_freq != 1000000 && dev->clk_freq != 3400000) {
+	if (t->bus_freq_hz != 100000 && t->bus_freq_hz != 400000 &&
+	    t->bus_freq_hz != 1000000 && t->bus_freq_hz != 3400000) {
 		dev_err(&pdev->dev,
 			"%d Hz is unsupported, only 100kHz, 400kHz, 1MHz and 3.4MHz are supported\n",
-			dev->clk_freq);
+			t->bus_freq_hz);
 		ret = -EINVAL;
 		goto exit_reset;
 	}
@@ -334,12 +318,14 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 
 	dev->clk = devm_clk_get(&pdev->dev, NULL);
 	if (!i2c_dw_prepare_clk(dev, true)) {
+		u64 clk_khz;
+
 		dev->get_clk_rate_khz = i2c_dw_get_clk_rate_khz;
+		clk_khz = dev->get_clk_rate_khz(dev);
 
-		if (!dev->sda_hold_time && ht)
-			dev->sda_hold_time = div_u64(
-				(u64)dev->get_clk_rate_khz(dev) * ht + 500000,
-				1000000);
+		if (!dev->sda_hold_time && t->sda_hold_ns)
+			dev->sda_hold_time =
+				div_u64(clk_khz * t->sda_hold_ns + 500000, 1000000);
 	}
 
 	dw_i2c_set_fifo_size(dev, pdev->id);
diff --git a/drivers/i2c/busses/i2c-designware-slave.c b/drivers/i2c/busses/i2c-designware-slave.c
index 8ce2cd368477..e7f9305b2dd9 100644
--- a/drivers/i2c/busses/i2c-designware-slave.c
+++ b/drivers/i2c/busses/i2c-designware-slave.c
@@ -1,23 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Synopsys DesignWare I2C adapter driver (slave only).
  *
  * Based on the Synopsys DesignWare I2C adapter driver (master).
  *
  * Copyright (C) 2016 Synopsys Inc.
- *
- * ----------------------------------------------------------------------------
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- * ----------------------------------------------------------------------------
- *
  */
 #include <linux/delay.h>
 #include <linux/err.h>
@@ -51,53 +38,18 @@ static void i2c_dw_configure_fifo_slave(struct dw_i2c_dev *dev)
  */
 static int i2c_dw_init_slave(struct dw_i2c_dev *dev)
 {
-	u32 reg, comp_param1;
 	int ret;
 
 	ret = i2c_dw_acquire_lock(dev);
 	if (ret)
 		return ret;
 
-	reg = dw_readl(dev, DW_IC_COMP_TYPE);
-	if (reg == ___constant_swab32(DW_IC_COMP_TYPE_VALUE)) {
-		/* Configure register endianness access. */
-		dev->flags |= ACCESS_SWAP;
-	} else if (reg == (DW_IC_COMP_TYPE_VALUE & 0x0000ffff)) {
-		/* Configure register access mode 16bit. */
-		dev->flags |= ACCESS_16BIT;
-	} else if (reg != DW_IC_COMP_TYPE_VALUE) {
-		dev_err(dev->dev,
-			"Unknown Synopsys component type: 0x%08x\n", reg);
-		i2c_dw_release_lock(dev);
-		return -ENODEV;
-	}
-
-	comp_param1 = dw_readl(dev, DW_IC_COMP_PARAM_1);
-
 	/* Disable the adapter. */
 	__i2c_dw_disable(dev);
 
-	/* Configure SDA Hold Time if required. */
-	reg = dw_readl(dev, DW_IC_COMP_VERSION);
-	if (reg >= DW_IC_SDA_HOLD_MIN_VERS) {
-		if (!dev->sda_hold_time) {
-			/* Keep previous hold time setting if no one set it. */
-			dev->sda_hold_time = dw_readl(dev, DW_IC_SDA_HOLD);
-		}
-		/*
-		 * Workaround for avoiding TX arbitration lost in case I2C
-		 * slave pulls SDA down "too quickly" after falling egde of
-		 * SCL by enabling non-zero SDA RX hold. Specification says it
-		 * extends incoming SDA low to high transition while SCL is
-		 * high but it apprears to help also above issue.
-		 */
-		if (!(dev->sda_hold_time & DW_IC_SDA_HOLD_RX_MASK))
-			dev->sda_hold_time |= 1 << DW_IC_SDA_HOLD_RX_SHIFT;
+	/* Write SDA hold time if supported */
+	if (dev->sda_hold_time)
 		dw_writel(dev, dev->sda_hold_time, DW_IC_SDA_HOLD);
-	} else {
-		dev_warn(dev->dev,
-			 "Hardware too old to adjust SDA hold time.\n");
-	}
 
 	i2c_dw_configure_fifo_slave(dev);
 	i2c_dw_release_lock(dev);
@@ -299,6 +251,14 @@ int i2c_dw_probe_slave(struct dw_i2c_dev *dev)
 	dev->disable = i2c_dw_disable;
 	dev->disable_int = i2c_dw_disable_int;
 
+	ret = i2c_dw_set_reg_access(dev);
+	if (ret)
+		return ret;
+
+	ret = i2c_dw_set_sda_hold(dev);
+	if (ret)
+		return ret;
+
 	ret = dev->init(dev);
 	if (ret)
 		return ret;
diff --git a/drivers/i2c/busses/i2c-exynos5.c b/drivers/i2c/busses/i2c-exynos5.c
index de82ad8ff534..c1ce2299a76e 100644
--- a/drivers/i2c/busses/i2c-exynos5.c
+++ b/drivers/i2c/busses/i2c-exynos5.c
@@ -176,7 +176,10 @@
 
 #define EXYNOS5_I2C_TIMEOUT (msecs_to_jiffies(100))
 
-#define HSI2C_EXYNOS7	BIT(0)
+enum i2c_type_exynos {
+	I2C_TYPE_EXYNOS5,
+	I2C_TYPE_EXYNOS7,
+};
 
 struct exynos5_i2c {
 	struct i2c_adapter	adap;
@@ -212,27 +215,30 @@ struct exynos5_i2c {
 /**
  * struct exynos_hsi2c_variant - platform specific HSI2C driver data
  * @fifo_depth: the fifo depth supported by the HSI2C module
+ * @hw: the hardware variant of Exynos I2C controller
  *
  * Specifies platform specific configuration of HSI2C module.
  * Note: A structure for driver specific platform data is used for future
  * expansion of its usage.
  */
 struct exynos_hsi2c_variant {
-	unsigned int	fifo_depth;
-	unsigned int	hw;
+	unsigned int		fifo_depth;
+	enum i2c_type_exynos	hw;
 };
 
 static const struct exynos_hsi2c_variant exynos5250_hsi2c_data = {
 	.fifo_depth	= 64,
+	.hw		= I2C_TYPE_EXYNOS5,
 };
 
 static const struct exynos_hsi2c_variant exynos5260_hsi2c_data = {
 	.fifo_depth	= 16,
+	.hw		= I2C_TYPE_EXYNOS5,
 };
 
 static const struct exynos_hsi2c_variant exynos7_hsi2c_data = {
 	.fifo_depth	= 16,
-	.hw		= HSI2C_EXYNOS7,
+	.hw		= I2C_TYPE_EXYNOS7,
 };
 
 static const struct of_device_id exynos5_i2c_match[] = {
@@ -300,7 +306,7 @@ static int exynos5_i2c_set_timing(struct exynos5_i2c *i2c, bool hs_timings)
 	 */
 	t_ftl_cycle = (readl(i2c->regs + HSI2C_CONF) >> 16) & 0x7;
 	temp = clkin / op_clk - 8 - t_ftl_cycle;
-	if (i2c->variant->hw != HSI2C_EXYNOS7)
+	if (i2c->variant->hw != I2C_TYPE_EXYNOS7)
 		temp -= t_ftl_cycle;
 	div = temp / 512;
 	clk_cycle = temp / (div + 1) - 2;
@@ -424,7 +430,7 @@ static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id)
 	writel(int_status, i2c->regs + HSI2C_INT_STATUS);
 
 	/* handle interrupt related to the transfer status */
-	if (i2c->variant->hw == HSI2C_EXYNOS7) {
+	if (i2c->variant->hw == I2C_TYPE_EXYNOS7) {
 		if (int_status & HSI2C_INT_TRANS_DONE) {
 			i2c->trans_done = 1;
 			i2c->state = 0;
@@ -571,7 +577,7 @@ static void exynos5_i2c_bus_check(struct exynos5_i2c *i2c)
 {
 	unsigned long timeout;
 
-	if (i2c->variant->hw != HSI2C_EXYNOS7)
+	if (i2c->variant->hw != I2C_TYPE_EXYNOS7)
 		return;
 
 	/*
@@ -612,7 +618,7 @@ static void exynos5_i2c_message_start(struct exynos5_i2c *i2c, int stop)
 	unsigned long flags;
 	unsigned short trig_lvl;
 
-	if (i2c->variant->hw == HSI2C_EXYNOS7)
+	if (i2c->variant->hw == I2C_TYPE_EXYNOS7)
 		int_en |= HSI2C_INT_I2C_TRANS;
 	else
 		int_en |= HSI2C_INT_I2C;
diff --git a/drivers/i2c/busses/i2c-fsi.c b/drivers/i2c/busses/i2c-fsi.c
new file mode 100644
index 000000000000..1e2be2219a60
--- /dev/null
+++ b/drivers/i2c/busses/i2c-fsi.c
@@ -0,0 +1,752 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * FSI-attached I2C master algorithm
+ *
+ * Copyright 2018 IBM Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/fsi.h>
+#include <linux/i2c.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/slab.h>
+
+#define FSI_ENGID_I2C		0x7
+
+#define I2C_DEFAULT_CLK_DIV	6
+
+/* i2c registers */
+#define I2C_FSI_FIFO		0x00
+#define I2C_FSI_CMD		0x04
+#define I2C_FSI_MODE		0x08
+#define I2C_FSI_WATER_MARK	0x0C
+#define I2C_FSI_INT_MASK	0x10
+#define I2C_FSI_INT_COND	0x14
+#define I2C_FSI_OR_INT_MASK	0x14
+#define I2C_FSI_INTS		0x18
+#define I2C_FSI_AND_INT_MASK	0x18
+#define I2C_FSI_STAT		0x1C
+#define I2C_FSI_RESET_I2C	0x1C
+#define I2C_FSI_ESTAT		0x20
+#define I2C_FSI_RESET_ERR	0x20
+#define I2C_FSI_RESID_LEN	0x24
+#define I2C_FSI_SET_SCL		0x24
+#define I2C_FSI_PORT_BUSY	0x28
+#define I2C_FSI_RESET_SCL	0x2C
+#define I2C_FSI_SET_SDA		0x30
+#define I2C_FSI_RESET_SDA	0x34
+
+/* cmd register */
+#define I2C_CMD_WITH_START	BIT(31)
+#define I2C_CMD_WITH_ADDR	BIT(30)
+#define I2C_CMD_RD_CONT		BIT(29)
+#define I2C_CMD_WITH_STOP	BIT(28)
+#define I2C_CMD_FORCELAUNCH	BIT(27)
+#define I2C_CMD_ADDR		GENMASK(23, 17)
+#define I2C_CMD_READ		BIT(16)
+#define I2C_CMD_LEN		GENMASK(15, 0)
+
+/* mode register */
+#define I2C_MODE_CLKDIV		GENMASK(31, 16)
+#define I2C_MODE_PORT		GENMASK(15, 10)
+#define I2C_MODE_ENHANCED	BIT(3)
+#define I2C_MODE_DIAG		BIT(2)
+#define I2C_MODE_PACE_ALLOW	BIT(1)
+#define I2C_MODE_WRAP		BIT(0)
+
+/* watermark register */
+#define I2C_WATERMARK_HI	GENMASK(15, 12)
+#define I2C_WATERMARK_LO	GENMASK(7, 4)
+
+#define I2C_FIFO_HI_LVL		4
+#define I2C_FIFO_LO_LVL		4
+
+/* interrupt register */
+#define I2C_INT_INV_CMD		BIT(15)
+#define I2C_INT_PARITY		BIT(14)
+#define I2C_INT_BE_OVERRUN	BIT(13)
+#define I2C_INT_BE_ACCESS	BIT(12)
+#define I2C_INT_LOST_ARB	BIT(11)
+#define I2C_INT_NACK		BIT(10)
+#define I2C_INT_DAT_REQ		BIT(9)
+#define I2C_INT_CMD_COMP	BIT(8)
+#define I2C_INT_STOP_ERR	BIT(7)
+#define I2C_INT_BUSY		BIT(6)
+#define I2C_INT_IDLE		BIT(5)
+
+/* status register */
+#define I2C_STAT_INV_CMD	BIT(31)
+#define I2C_STAT_PARITY		BIT(30)
+#define I2C_STAT_BE_OVERRUN	BIT(29)
+#define I2C_STAT_BE_ACCESS	BIT(28)
+#define I2C_STAT_LOST_ARB	BIT(27)
+#define I2C_STAT_NACK		BIT(26)
+#define I2C_STAT_DAT_REQ	BIT(25)
+#define I2C_STAT_CMD_COMP	BIT(24)
+#define I2C_STAT_STOP_ERR	BIT(23)
+#define I2C_STAT_MAX_PORT	GENMASK(19, 16)
+#define I2C_STAT_ANY_INT	BIT(15)
+#define I2C_STAT_SCL_IN		BIT(11)
+#define I2C_STAT_SDA_IN		BIT(10)
+#define I2C_STAT_PORT_BUSY	BIT(9)
+#define I2C_STAT_SELF_BUSY	BIT(8)
+#define I2C_STAT_FIFO_COUNT	GENMASK(7, 0)
+
+#define I2C_STAT_ERR		(I2C_STAT_INV_CMD |			\
+				 I2C_STAT_PARITY |			\
+				 I2C_STAT_BE_OVERRUN |			\
+				 I2C_STAT_BE_ACCESS |			\
+				 I2C_STAT_LOST_ARB |			\
+				 I2C_STAT_NACK |			\
+				 I2C_STAT_STOP_ERR)
+#define I2C_STAT_ANY_RESP	(I2C_STAT_ERR |				\
+				 I2C_STAT_DAT_REQ |			\
+				 I2C_STAT_CMD_COMP)
+
+/* extended status register */
+#define I2C_ESTAT_FIFO_SZ	GENMASK(31, 24)
+#define I2C_ESTAT_SCL_IN_SY	BIT(15)
+#define I2C_ESTAT_SDA_IN_SY	BIT(14)
+#define I2C_ESTAT_S_SCL		BIT(13)
+#define I2C_ESTAT_S_SDA		BIT(12)
+#define I2C_ESTAT_M_SCL		BIT(11)
+#define I2C_ESTAT_M_SDA		BIT(10)
+#define I2C_ESTAT_HI_WATER	BIT(9)
+#define I2C_ESTAT_LO_WATER	BIT(8)
+#define I2C_ESTAT_PORT_BUSY	BIT(7)
+#define I2C_ESTAT_SELF_BUSY	BIT(6)
+#define I2C_ESTAT_VERSION	GENMASK(4, 0)
+
+/* port busy register */
+#define I2C_PORT_BUSY_RESET	BIT(31)
+
+/* wait for command complete or data request */
+#define I2C_CMD_SLEEP_MAX_US	500
+#define I2C_CMD_SLEEP_MIN_US	50
+
+/* wait after reset; choose time from legacy driver */
+#define I2C_RESET_SLEEP_MAX_US	2000
+#define I2C_RESET_SLEEP_MIN_US	1000
+
+/* choose timeout length from legacy driver; it's well tested */
+#define I2C_ABORT_TIMEOUT	msecs_to_jiffies(100)
+
+struct fsi_i2c_master {
+	struct fsi_device	*fsi;
+	u8			fifo_size;
+	struct list_head	ports;
+	struct mutex		lock;
+};
+
+struct fsi_i2c_port {
+	struct list_head	list;
+	struct i2c_adapter	adapter;
+	struct fsi_i2c_master	*master;
+	u16			port;
+	u16			xfrd;
+};
+
+static int fsi_i2c_read_reg(struct fsi_device *fsi, unsigned int reg,
+			    u32 *data)
+{
+	int rc;
+	__be32 data_be;
+
+	rc = fsi_device_read(fsi, reg, &data_be, sizeof(data_be));
+	if (rc)
+		return rc;
+
+	*data = be32_to_cpu(data_be);
+
+	return 0;
+}
+
+static int fsi_i2c_write_reg(struct fsi_device *fsi, unsigned int reg,
+			     u32 *data)
+{
+	__be32 data_be = cpu_to_be32p(data);
+
+	return fsi_device_write(fsi, reg, &data_be, sizeof(data_be));
+}
+
+static int fsi_i2c_dev_init(struct fsi_i2c_master *i2c)
+{
+	int rc;
+	u32 mode = I2C_MODE_ENHANCED, extended_status, watermark;
+	u32 interrupt = 0;
+
+	/* since we use polling, disable interrupts */
+	rc = fsi_i2c_write_reg(i2c->fsi, I2C_FSI_INT_MASK, &interrupt);
+	if (rc)
+		return rc;
+
+	mode |= FIELD_PREP(I2C_MODE_CLKDIV, I2C_DEFAULT_CLK_DIV);
+	rc = fsi_i2c_write_reg(i2c->fsi, I2C_FSI_MODE, &mode);
+	if (rc)
+		return rc;
+
+	rc = fsi_i2c_read_reg(i2c->fsi, I2C_FSI_ESTAT, &extended_status);
+	if (rc)
+		return rc;
+
+	i2c->fifo_size = FIELD_GET(I2C_ESTAT_FIFO_SZ, extended_status);
+	watermark = FIELD_PREP(I2C_WATERMARK_HI,
+			       i2c->fifo_size - I2C_FIFO_HI_LVL);
+	watermark |= FIELD_PREP(I2C_WATERMARK_LO, I2C_FIFO_LO_LVL);
+
+	return fsi_i2c_write_reg(i2c->fsi, I2C_FSI_WATER_MARK, &watermark);
+}
+
+static int fsi_i2c_set_port(struct fsi_i2c_port *port)
+{
+	int rc;
+	struct fsi_device *fsi = port->master->fsi;
+	u32 mode, dummy = 0;
+
+	rc = fsi_i2c_read_reg(fsi, I2C_FSI_MODE, &mode);
+	if (rc)
+		return rc;
+
+	if (FIELD_GET(I2C_MODE_PORT, mode) == port->port)
+		return 0;
+
+	mode = (mode & ~I2C_MODE_PORT) | FIELD_PREP(I2C_MODE_PORT, port->port);
+	rc = fsi_i2c_write_reg(fsi, I2C_FSI_MODE, &mode);
+	if (rc)
+		return rc;
+
+	/* reset engine when port is changed */
+	return fsi_i2c_write_reg(fsi, I2C_FSI_RESET_ERR, &dummy);
+}
+
+static int fsi_i2c_start(struct fsi_i2c_port *port, struct i2c_msg *msg,
+			 bool stop)
+{
+	struct fsi_i2c_master *i2c = port->master;
+	u32 cmd = I2C_CMD_WITH_START | I2C_CMD_WITH_ADDR;
+
+	port->xfrd = 0;
+
+	if (msg->flags & I2C_M_RD)
+		cmd |= I2C_CMD_READ;
+
+	if (stop || msg->flags & I2C_M_STOP)
+		cmd |= I2C_CMD_WITH_STOP;
+
+	cmd |= FIELD_PREP(I2C_CMD_ADDR, msg->addr);
+	cmd |= FIELD_PREP(I2C_CMD_LEN, msg->len);
+
+	return fsi_i2c_write_reg(i2c->fsi, I2C_FSI_CMD, &cmd);
+}
+
+static int fsi_i2c_get_op_bytes(int op_bytes)
+{
+	/* fsi is limited to max 4 byte aligned ops */
+	if (op_bytes > 4)
+		return 4;
+	else if (op_bytes == 3)
+		return 2;
+	return op_bytes;
+}
+
+static int fsi_i2c_write_fifo(struct fsi_i2c_port *port, struct i2c_msg *msg,
+			      u8 fifo_count)
+{
+	int write;
+	int rc;
+	struct fsi_i2c_master *i2c = port->master;
+	int bytes_to_write = i2c->fifo_size - fifo_count;
+	int bytes_remaining = msg->len - port->xfrd;
+
+	bytes_to_write = min(bytes_to_write, bytes_remaining);
+
+	while (bytes_to_write) {
+		write = fsi_i2c_get_op_bytes(bytes_to_write);
+
+		rc = fsi_device_write(i2c->fsi, I2C_FSI_FIFO,
+				      &msg->buf[port->xfrd], write);
+		if (rc)
+			return rc;
+
+		port->xfrd += write;
+		bytes_to_write -= write;
+	}
+
+	return 0;
+}
+
+static int fsi_i2c_read_fifo(struct fsi_i2c_port *port, struct i2c_msg *msg,
+			     u8 fifo_count)
+{
+	int read;
+	int rc;
+	struct fsi_i2c_master *i2c = port->master;
+	int bytes_to_read;
+	int xfr_remaining = msg->len - port->xfrd;
+	u32 dummy;
+
+	bytes_to_read = min_t(int, fifo_count, xfr_remaining);
+
+	while (bytes_to_read) {
+		read = fsi_i2c_get_op_bytes(bytes_to_read);
+
+		if (xfr_remaining) {
+			rc = fsi_device_read(i2c->fsi, I2C_FSI_FIFO,
+					     &msg->buf[port->xfrd], read);
+			if (rc)
+				return rc;
+
+			port->xfrd += read;
+			xfr_remaining -= read;
+		} else {
+			/* no more buffer but data in fifo, need to clear it */
+			rc = fsi_device_read(i2c->fsi, I2C_FSI_FIFO, &dummy,
+					     read);
+			if (rc)
+				return rc;
+		}
+
+		bytes_to_read -= read;
+	}
+
+	return 0;
+}
+
+static int fsi_i2c_get_scl(struct i2c_adapter *adap)
+{
+	u32 stat = 0;
+	struct fsi_i2c_port *port = adap->algo_data;
+	struct fsi_i2c_master *i2c = port->master;
+
+	fsi_i2c_read_reg(i2c->fsi, I2C_FSI_STAT, &stat);
+
+	return !!(stat & I2C_STAT_SCL_IN);
+}
+
+static void fsi_i2c_set_scl(struct i2c_adapter *adap, int val)
+{
+	u32 dummy = 0;
+	struct fsi_i2c_port *port = adap->algo_data;
+	struct fsi_i2c_master *i2c = port->master;
+
+	if (val)
+		fsi_i2c_write_reg(i2c->fsi, I2C_FSI_SET_SCL, &dummy);
+	else
+		fsi_i2c_write_reg(i2c->fsi, I2C_FSI_RESET_SCL, &dummy);
+}
+
+static int fsi_i2c_get_sda(struct i2c_adapter *adap)
+{
+	u32 stat = 0;
+	struct fsi_i2c_port *port = adap->algo_data;
+	struct fsi_i2c_master *i2c = port->master;
+
+	fsi_i2c_read_reg(i2c->fsi, I2C_FSI_STAT, &stat);
+
+	return !!(stat & I2C_STAT_SDA_IN);
+}
+
+static void fsi_i2c_set_sda(struct i2c_adapter *adap, int val)
+{
+	u32 dummy = 0;
+	struct fsi_i2c_port *port = adap->algo_data;
+	struct fsi_i2c_master *i2c = port->master;
+
+	if (val)
+		fsi_i2c_write_reg(i2c->fsi, I2C_FSI_SET_SDA, &dummy);
+	else
+		fsi_i2c_write_reg(i2c->fsi, I2C_FSI_RESET_SDA, &dummy);
+}
+
+static void fsi_i2c_prepare_recovery(struct i2c_adapter *adap)
+{
+	int rc;
+	u32 mode;
+	struct fsi_i2c_port *port = adap->algo_data;
+	struct fsi_i2c_master *i2c = port->master;
+
+	rc = fsi_i2c_read_reg(i2c->fsi, I2C_FSI_MODE, &mode);
+	if (rc)
+		return;
+
+	mode |= I2C_MODE_DIAG;
+	fsi_i2c_write_reg(i2c->fsi, I2C_FSI_MODE, &mode);
+}
+
+static void fsi_i2c_unprepare_recovery(struct i2c_adapter *adap)
+{
+	int rc;
+	u32 mode;
+	struct fsi_i2c_port *port = adap->algo_data;
+	struct fsi_i2c_master *i2c = port->master;
+
+	rc = fsi_i2c_read_reg(i2c->fsi, I2C_FSI_MODE, &mode);
+	if (rc)
+		return;
+
+	mode &= ~I2C_MODE_DIAG;
+	fsi_i2c_write_reg(i2c->fsi, I2C_FSI_MODE, &mode);
+}
+
+static int fsi_i2c_reset_bus(struct fsi_i2c_master *i2c,
+			     struct fsi_i2c_port *port)
+{
+	int rc;
+	u32 stat, dummy = 0;
+
+	/* force bus reset, ignore errors */
+	i2c_recover_bus(&port->adapter);
+
+	/* reset errors */
+	rc = fsi_i2c_write_reg(i2c->fsi, I2C_FSI_RESET_ERR, &dummy);
+	if (rc)
+		return rc;
+
+	/* wait for command complete */
+	usleep_range(I2C_RESET_SLEEP_MIN_US, I2C_RESET_SLEEP_MAX_US);
+
+	rc = fsi_i2c_read_reg(i2c->fsi, I2C_FSI_STAT, &stat);
+	if (rc)
+		return rc;
+
+	if (stat & I2C_STAT_CMD_COMP)
+		return 0;
+
+	/* failed to get command complete; reset engine again */
+	rc = fsi_i2c_write_reg(i2c->fsi, I2C_FSI_RESET_I2C, &dummy);
+	if (rc)
+		return rc;
+
+	/* re-init engine again */
+	return fsi_i2c_dev_init(i2c);
+}
+
+static int fsi_i2c_reset_engine(struct fsi_i2c_master *i2c, u16 port)
+{
+	int rc;
+	u32 mode, dummy = 0;
+
+	/* reset engine */
+	rc = fsi_i2c_write_reg(i2c->fsi, I2C_FSI_RESET_I2C, &dummy);
+	if (rc)
+		return rc;
+
+	/* re-init engine */
+	rc = fsi_i2c_dev_init(i2c);
+	if (rc)
+		return rc;
+
+	rc = fsi_i2c_read_reg(i2c->fsi, I2C_FSI_MODE, &mode);
+	if (rc)
+		return rc;
+
+	/* set port; default after reset is 0 */
+	if (port) {
+		mode &= ~I2C_MODE_PORT;
+		mode |= FIELD_PREP(I2C_MODE_PORT, port);
+		rc = fsi_i2c_write_reg(i2c->fsi, I2C_FSI_MODE, &mode);
+		if (rc)
+			return rc;
+	}
+
+	/* reset busy register; hw workaround */
+	dummy = I2C_PORT_BUSY_RESET;
+	rc = fsi_i2c_write_reg(i2c->fsi, I2C_FSI_PORT_BUSY, &dummy);
+	if (rc)
+		return rc;
+
+	return 0;
+}
+
+static int fsi_i2c_abort(struct fsi_i2c_port *port, u32 status)
+{
+	int rc;
+	unsigned long start;
+	u32 cmd = I2C_CMD_WITH_STOP;
+	u32 stat;
+	struct fsi_i2c_master *i2c = port->master;
+	struct fsi_device *fsi = i2c->fsi;
+
+	rc = fsi_i2c_reset_engine(i2c, port->port);
+	if (rc)
+		return rc;
+
+	rc = fsi_i2c_read_reg(fsi, I2C_FSI_STAT, &stat);
+	if (rc)
+		return rc;
+
+	/* if sda is low, peform full bus reset */
+	if (!(stat & I2C_STAT_SDA_IN)) {
+		rc = fsi_i2c_reset_bus(i2c, port);
+		if (rc)
+			return rc;
+	}
+
+	/* skip final stop command for these errors */
+	if (status & (I2C_STAT_PARITY | I2C_STAT_LOST_ARB | I2C_STAT_STOP_ERR))
+		return 0;
+
+	/* write stop command */
+	rc = fsi_i2c_write_reg(fsi, I2C_FSI_CMD, &cmd);
+	if (rc)
+		return rc;
+
+	/* wait until we see command complete in the master */
+	start = jiffies;
+
+	do {
+		rc = fsi_i2c_read_reg(fsi, I2C_FSI_STAT, &status);
+		if (rc)
+			return rc;
+
+		if (status & I2C_STAT_CMD_COMP)
+			return 0;
+
+		usleep_range(I2C_CMD_SLEEP_MIN_US, I2C_CMD_SLEEP_MAX_US);
+	} while (time_after(start + I2C_ABORT_TIMEOUT, jiffies));
+
+	return -ETIMEDOUT;
+}
+
+static int fsi_i2c_handle_status(struct fsi_i2c_port *port,
+				 struct i2c_msg *msg, u32 status)
+{
+	int rc;
+	u8 fifo_count;
+
+	if (status & I2C_STAT_ERR) {
+		rc = fsi_i2c_abort(port, status);
+		if (rc)
+			return rc;
+
+		if (status & I2C_STAT_INV_CMD)
+			return -EINVAL;
+
+		if (status & (I2C_STAT_PARITY | I2C_STAT_BE_OVERRUN |
+		    I2C_STAT_BE_ACCESS))
+			return -EPROTO;
+
+		if (status & I2C_STAT_NACK)
+			return -ENXIO;
+
+		if (status & I2C_STAT_LOST_ARB)
+			return -EAGAIN;
+
+		if (status & I2C_STAT_STOP_ERR)
+			return -EBADMSG;
+
+		return -EIO;
+	}
+
+	if (status & I2C_STAT_DAT_REQ) {
+		fifo_count = FIELD_GET(I2C_STAT_FIFO_COUNT, status);
+
+		if (msg->flags & I2C_M_RD)
+			return fsi_i2c_read_fifo(port, msg, fifo_count);
+
+		return fsi_i2c_write_fifo(port, msg, fifo_count);
+	}
+
+	if (status & I2C_STAT_CMD_COMP) {
+		if (port->xfrd < msg->len)
+			return -ENODATA;
+
+		return msg->len;
+	}
+
+	return 0;
+}
+
+static int fsi_i2c_wait(struct fsi_i2c_port *port, struct i2c_msg *msg,
+			unsigned long timeout)
+{
+	u32 status = 0;
+	int rc;
+	unsigned long start = jiffies;
+
+	do {
+		rc = fsi_i2c_read_reg(port->master->fsi, I2C_FSI_STAT,
+				      &status);
+		if (rc)
+			return rc;
+
+		if (status & I2C_STAT_ANY_RESP) {
+			rc = fsi_i2c_handle_status(port, msg, status);
+			if (rc < 0)
+				return rc;
+
+			/* cmd complete and all data xfrd */
+			if (rc == msg->len)
+				return 0;
+
+			/* need to xfr more data, but maybe don't need wait */
+			continue;
+		}
+
+		usleep_range(I2C_CMD_SLEEP_MIN_US, I2C_CMD_SLEEP_MAX_US);
+	} while (time_after(start + timeout, jiffies));
+
+	return -ETIMEDOUT;
+}
+
+static int fsi_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
+			int num)
+{
+	int i, rc;
+	unsigned long start_time;
+	struct fsi_i2c_port *port = adap->algo_data;
+	struct fsi_i2c_master *master = port->master;
+	struct i2c_msg *msg;
+
+	mutex_lock(&master->lock);
+
+	rc = fsi_i2c_set_port(port);
+	if (rc)
+		goto unlock;
+
+	for (i = 0; i < num; i++) {
+		msg = msgs + i;
+		start_time = jiffies;
+
+		rc = fsi_i2c_start(port, msg, i == num - 1);
+		if (rc)
+			goto unlock;
+
+		rc = fsi_i2c_wait(port, msg,
+				  adap->timeout - (jiffies - start_time));
+		if (rc)
+			goto unlock;
+	}
+
+unlock:
+	mutex_unlock(&master->lock);
+	return rc ? : num;
+}
+
+static u32 fsi_i2c_functionality(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_PROTOCOL_MANGLING |
+		I2C_FUNC_SMBUS_EMUL | I2C_FUNC_SMBUS_BLOCK_DATA;
+}
+
+static struct i2c_bus_recovery_info fsi_i2c_bus_recovery_info = {
+	.recover_bus = i2c_generic_scl_recovery,
+	.get_scl = fsi_i2c_get_scl,
+	.set_scl = fsi_i2c_set_scl,
+	.get_sda = fsi_i2c_get_sda,
+	.set_sda = fsi_i2c_set_sda,
+	.prepare_recovery = fsi_i2c_prepare_recovery,
+	.unprepare_recovery = fsi_i2c_unprepare_recovery,
+};
+
+static const struct i2c_algorithm fsi_i2c_algorithm = {
+	.master_xfer = fsi_i2c_xfer,
+	.functionality = fsi_i2c_functionality,
+};
+
+static int fsi_i2c_probe(struct device *dev)
+{
+	struct fsi_i2c_master *i2c;
+	struct fsi_i2c_port *port;
+	struct device_node *np;
+	int rc;
+	u32 port_no;
+
+	i2c = devm_kzalloc(dev, sizeof(*i2c), GFP_KERNEL);
+	if (!i2c)
+		return -ENOMEM;
+
+	mutex_init(&i2c->lock);
+	i2c->fsi = to_fsi_dev(dev);
+	INIT_LIST_HEAD(&i2c->ports);
+
+	rc = fsi_i2c_dev_init(i2c);
+	if (rc)
+		return rc;
+
+	/* Add adapter for each i2c port of the master. */
+	for_each_available_child_of_node(dev->of_node, np) {
+		rc = of_property_read_u32(np, "reg", &port_no);
+		if (rc || port_no > USHRT_MAX)
+			continue;
+
+		port = kzalloc(sizeof(*port), GFP_KERNEL);
+		if (!port)
+			break;
+
+		port->master = i2c;
+		port->port = port_no;
+
+		port->adapter.owner = THIS_MODULE;
+		port->adapter.dev.of_node = np;
+		port->adapter.dev.parent = dev;
+		port->adapter.algo = &fsi_i2c_algorithm;
+		port->adapter.bus_recovery_info = &fsi_i2c_bus_recovery_info;
+		port->adapter.algo_data = port;
+
+		snprintf(port->adapter.name, sizeof(port->adapter.name),
+			 "i2c_bus-%u", port_no);
+
+		rc = i2c_add_adapter(&port->adapter);
+		if (rc < 0) {
+			dev_err(dev, "Failed to register adapter: %d\n", rc);
+			kfree(port);
+			continue;
+		}
+
+		list_add(&port->list, &i2c->ports);
+	}
+
+	dev_set_drvdata(dev, i2c);
+
+	return 0;
+}
+
+static int fsi_i2c_remove(struct device *dev)
+{
+	struct fsi_i2c_master *i2c = dev_get_drvdata(dev);
+	struct fsi_i2c_port *port, *tmp;
+
+	list_for_each_entry_safe(port, tmp, &i2c->ports, list) {
+		list_del(&port->list);
+		i2c_del_adapter(&port->adapter);
+		kfree(port);
+	}
+
+	return 0;
+}
+
+static const struct fsi_device_id fsi_i2c_ids[] = {
+	{ FSI_ENGID_I2C, FSI_VERSION_ANY },
+	{ }
+};
+
+static struct fsi_driver fsi_i2c_driver = {
+	.id_table = fsi_i2c_ids,
+	.drv = {
+		.name = "i2c-fsi",
+		.bus = &fsi_bus_type,
+		.probe = fsi_i2c_probe,
+		.remove = fsi_i2c_remove,
+	},
+};
+
+module_fsi_driver(fsi_i2c_driver);
+
+MODULE_AUTHOR("Eddie James <eajames@us.ibm.com>");
+MODULE_DESCRIPTION("FSI attached I2C master");
+MODULE_LICENSE("GPL");
diff --git a/drivers/i2c/busses/i2c-gpio.c b/drivers/i2c/busses/i2c-gpio.c
index 66f85bbf3591..c008d209f0b8 100644
--- a/drivers/i2c/busses/i2c-gpio.c
+++ b/drivers/i2c/busses/i2c-gpio.c
@@ -78,49 +78,43 @@ static struct dentry *i2c_gpio_debug_dir;
 #define getscl(bd)	((bd)->getscl((bd)->data))
 
 #define WIRE_ATTRIBUTE(wire) \
-static int fops_##wire##_get(void *data, u64 *val)	\
-{							\
-	struct i2c_gpio_private_data *priv = data;	\
-							\
-	i2c_lock_adapter(&priv->adap);			\
-	*val = get##wire(&priv->bit_data);		\
-	i2c_unlock_adapter(&priv->adap);		\
-	return 0;					\
-}							\
-static int fops_##wire##_set(void *data, u64 val)	\
-{							\
-	struct i2c_gpio_private_data *priv = data;	\
-							\
-	i2c_lock_adapter(&priv->adap);			\
-	set##wire(&priv->bit_data, val);		\
-	i2c_unlock_adapter(&priv->adap);		\
-	return 0;					\
-}							\
+static int fops_##wire##_get(void *data, u64 *val)		\
+{								\
+	struct i2c_gpio_private_data *priv = data;		\
+								\
+	i2c_lock_bus(&priv->adap, I2C_LOCK_ROOT_ADAPTER);	\
+	*val = get##wire(&priv->bit_data);			\
+	i2c_unlock_bus(&priv->adap, I2C_LOCK_ROOT_ADAPTER);	\
+	return 0;						\
+}								\
+static int fops_##wire##_set(void *data, u64 val)		\
+{								\
+	struct i2c_gpio_private_data *priv = data;		\
+								\
+	i2c_lock_bus(&priv->adap, I2C_LOCK_ROOT_ADAPTER);	\
+	set##wire(&priv->bit_data, val);			\
+	i2c_unlock_bus(&priv->adap, I2C_LOCK_ROOT_ADAPTER);	\
+	return 0;						\
+}								\
 DEFINE_DEBUGFS_ATTRIBUTE(fops_##wire, fops_##wire##_get, fops_##wire##_set, "%llu\n")
 
 WIRE_ATTRIBUTE(scl);
 WIRE_ATTRIBUTE(sda);
 
-static int fops_incomplete_transfer_set(void *data, u64 addr)
+static void i2c_gpio_incomplete_transfer(struct i2c_gpio_private_data *priv,
+					u32 pattern, u8 pattern_size)
 {
-	struct i2c_gpio_private_data *priv = data;
 	struct i2c_algo_bit_data *bit_data = &priv->bit_data;
-	int i, pattern;
+	int i;
 
-	if (addr > 0x7f)
-		return -EINVAL;
-
-	/* ADDR (7 bit) + RD (1 bit) + SDA hi (1 bit) */
-	pattern = (addr << 2) | 3;
-
-	i2c_lock_adapter(&priv->adap);
+	i2c_lock_bus(&priv->adap, I2C_LOCK_ROOT_ADAPTER);
 
 	/* START condition */
 	setsda(bit_data, 0);
 	udelay(bit_data->udelay);
 
-	/* Send ADDR+RD, request ACK, don't send STOP */
-	for (i = 8; i >= 0; i--) {
+	/* Send pattern, request ACK, don't send STOP */
+	for (i = pattern_size - 1; i >= 0; i--) {
 		setscl(bit_data, 0);
 		udelay(bit_data->udelay / 2);
 		setsda(bit_data, (pattern >> i) & 1);
@@ -129,11 +123,44 @@ static int fops_incomplete_transfer_set(void *data, u64 addr)
 		udelay(bit_data->udelay);
 	}
 
-	i2c_unlock_adapter(&priv->adap);
+	i2c_unlock_bus(&priv->adap, I2C_LOCK_ROOT_ADAPTER);
+}
+
+static int fops_incomplete_addr_phase_set(void *data, u64 addr)
+{
+	struct i2c_gpio_private_data *priv = data;
+	u32 pattern;
+
+	if (addr > 0x7f)
+		return -EINVAL;
+
+	/* ADDR (7 bit) + RD (1 bit) + Client ACK, keep SDA hi (1 bit) */
+	pattern = (addr << 2) | 3;
+
+	i2c_gpio_incomplete_transfer(priv, pattern, 9);
+
+	return 0;
+}
+DEFINE_DEBUGFS_ATTRIBUTE(fops_incomplete_addr_phase, NULL, fops_incomplete_addr_phase_set, "%llu\n");
+
+static int fops_incomplete_write_byte_set(void *data, u64 addr)
+{
+	struct i2c_gpio_private_data *priv = data;
+	u32 pattern;
+
+	if (addr > 0x7f)
+		return -EINVAL;
+
+	/* ADDR (7 bit) + WR (1 bit) + Client ACK (1 bit) */
+	pattern = (addr << 2) | 1;
+	/* 0x00 (8 bit) + Client ACK, keep SDA hi (1 bit) */
+	pattern = (pattern << 9) | 1;
+
+	i2c_gpio_incomplete_transfer(priv, pattern, 18);
 
 	return 0;
 }
-DEFINE_DEBUGFS_ATTRIBUTE(fops_incomplete_transfer, NULL, fops_incomplete_transfer_set, "%llu\n");
+DEFINE_DEBUGFS_ATTRIBUTE(fops_incomplete_write_byte, NULL, fops_incomplete_write_byte_set, "%llu\n");
 
 static void i2c_gpio_fault_injector_init(struct platform_device *pdev)
 {
@@ -156,8 +183,10 @@ static void i2c_gpio_fault_injector_init(struct platform_device *pdev)
 
 	debugfs_create_file_unsafe("scl", 0600, priv->debug_dir, priv, &fops_scl);
 	debugfs_create_file_unsafe("sda", 0600, priv->debug_dir, priv, &fops_sda);
-	debugfs_create_file_unsafe("incomplete_transfer", 0200, priv->debug_dir,
-				   priv, &fops_incomplete_transfer);
+	debugfs_create_file_unsafe("incomplete_address_phase", 0200, priv->debug_dir,
+				   priv, &fops_incomplete_addr_phase);
+	debugfs_create_file_unsafe("incomplete_write_byte", 0200, priv->debug_dir,
+				   priv, &fops_incomplete_write_byte);
 }
 
 static void i2c_gpio_fault_injector_exit(struct platform_device *pdev)
diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c
index aa726607645e..941c223f6491 100644
--- a/drivers/i2c/busses/i2c-i801.c
+++ b/drivers/i2c/busses/i2c-i801.c
@@ -70,6 +70,7 @@
  * Cannon Lake-H (PCH)		0xa323	32	hard	yes	yes	yes
  * Cannon Lake-LP (PCH)		0x9da3	32	hard	yes	yes	yes
  * Cedar Fork (PCH)		0x18df	32	hard	yes	yes	yes
+ * Ice Lake-LP (PCH)		0x34a3	32	hard	yes	yes	yes
  *
  * Features supported by this driver:
  * Software PEC				no
@@ -220,6 +221,7 @@
 #define PCI_DEVICE_ID_INTEL_DH89XXCC_SMBUS		0x2330
 #define PCI_DEVICE_ID_INTEL_COLETOCREEK_SMBUS		0x23b0
 #define PCI_DEVICE_ID_INTEL_GEMINILAKE_SMBUS		0x31d4
+#define PCI_DEVICE_ID_INTEL_ICELAKE_LP_SMBUS		0x34a3
 #define PCI_DEVICE_ID_INTEL_5_3400_SERIES_SMBUS		0x3b30
 #define PCI_DEVICE_ID_INTEL_BROXTON_SMBUS		0x5ad4
 #define PCI_DEVICE_ID_INTEL_LYNXPOINT_SMBUS		0x8c22
@@ -1034,6 +1036,7 @@ static const struct pci_device_id i801_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_KABYLAKE_PCH_H_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CANNONLAKE_H_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CANNONLAKE_LP_SMBUS) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICELAKE_LP_SMBUS) },
 	{ 0, }
 };
 
@@ -1518,6 +1521,7 @@ static int i801_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	case PCI_DEVICE_ID_INTEL_CDF_SMBUS:
 	case PCI_DEVICE_ID_INTEL_DNV_SMBUS:
 	case PCI_DEVICE_ID_INTEL_KABYLAKE_PCH_H_SMBUS:
+	case PCI_DEVICE_ID_INTEL_ICELAKE_LP_SMBUS:
 		priv->features |= FEATURE_I2C_BLOCK_READ;
 		priv->features |= FEATURE_IRQ;
 		priv->features |= FEATURE_SMBUS_PEC;
diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
index 498c5e891649..c406700789e1 100644
--- a/drivers/i2c/busses/i2c-imx.c
+++ b/drivers/i2c/busses/i2c-imx.c
@@ -421,10 +421,14 @@ static int i2c_imx_bus_busy(struct imx_i2c_struct *i2c_imx, int for_busy)
 			return -EAGAIN;
 		}
 
-		if (for_busy && (temp & I2SR_IBB))
+		if (for_busy && (temp & I2SR_IBB)) {
+			i2c_imx->stopped = 0;
 			break;
-		if (!for_busy && !(temp & I2SR_IBB))
+		}
+		if (!for_busy && !(temp & I2SR_IBB)) {
+			i2c_imx->stopped = 1;
 			break;
+		}
 		if (time_after(jiffies, orig_jiffies + msecs_to_jiffies(500))) {
 			dev_dbg(&i2c_imx->adapter.dev,
 				"<%s> I2C bus is busy\n", __func__);
@@ -538,7 +542,6 @@ static int i2c_imx_start(struct imx_i2c_struct *i2c_imx)
 	result = i2c_imx_bus_busy(i2c_imx, 1);
 	if (result)
 		return result;
-	i2c_imx->stopped = 0;
 
 	temp |= I2CR_IIEN | I2CR_MTX | I2CR_TXAK;
 	temp &= ~I2CR_DMAEN;
@@ -567,10 +570,8 @@ static void i2c_imx_stop(struct imx_i2c_struct *i2c_imx)
 		udelay(i2c_imx->disable_delay);
 	}
 
-	if (!i2c_imx->stopped) {
+	if (!i2c_imx->stopped)
 		i2c_imx_bus_busy(i2c_imx, 0);
-		i2c_imx->stopped = 1;
-	}
 
 	/* Disable I2C controller */
 	temp = i2c_imx->hwdata->i2cr_ien_opcode ^ I2CR_IEN,
@@ -668,9 +669,6 @@ static int i2c_imx_dma_read(struct imx_i2c_struct *i2c_imx,
 	struct imx_i2c_dma *dma = i2c_imx->dma;
 	struct device *dev = &i2c_imx->adapter.dev;
 
-	temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
-	temp |= I2CR_DMAEN;
-	imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 
 	dma->chan_using = dma->chan_rx;
 	dma->dma_transfer_dir = DMA_DEV_TO_MEM;
@@ -727,7 +725,6 @@ static int i2c_imx_dma_read(struct imx_i2c_struct *i2c_imx,
 		temp &= ~(I2CR_MSTA | I2CR_MTX);
 		imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 		i2c_imx_bus_busy(i2c_imx, 0);
-		i2c_imx->stopped = 1;
 	} else {
 		/*
 		 * For i2c master receiver repeat restart operation like:
@@ -783,6 +780,7 @@ static int i2c_imx_read(struct imx_i2c_struct *i2c_imx, struct i2c_msg *msgs, bo
 	int i, result;
 	unsigned int temp;
 	int block_data = msgs->flags & I2C_M_RECV_LEN;
+	int use_dma = i2c_imx->dma && msgs->len >= DMA_THRESHOLD && !block_data;
 
 	dev_dbg(&i2c_imx->adapter.dev,
 		"<%s> write slave address: addr=0x%x\n",
@@ -809,12 +807,14 @@ static int i2c_imx_read(struct imx_i2c_struct *i2c_imx, struct i2c_msg *msgs, bo
 	 */
 	if ((msgs->len - 1) || block_data)
 		temp &= ~I2CR_TXAK;
+	if (use_dma)
+		temp |= I2CR_DMAEN;
 	imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 	imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR); /* dummy read */
 
 	dev_dbg(&i2c_imx->adapter.dev, "<%s> read data\n", __func__);
 
-	if (i2c_imx->dma && msgs->len >= DMA_THRESHOLD && !block_data)
+	if (use_dma)
 		return i2c_imx_dma_read(i2c_imx, msgs, is_lastmsg);
 
 	/* read data */
@@ -850,7 +850,6 @@ static int i2c_imx_read(struct imx_i2c_struct *i2c_imx, struct i2c_msg *msgs, bo
 				temp &= ~(I2CR_MSTA | I2CR_MTX);
 				imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 				i2c_imx_bus_busy(i2c_imx, 0);
-				i2c_imx->stopped = 1;
 			} else {
 				/*
 				 * For i2c master receiver repeat restart operation like:
diff --git a/drivers/i2c/busses/i2c-mxs.c b/drivers/i2c/busses/i2c-mxs.c
index 642c58946d8d..7d79317a1046 100644
--- a/drivers/i2c/busses/i2c-mxs.c
+++ b/drivers/i2c/busses/i2c-mxs.c
@@ -567,9 +567,6 @@ static int mxs_i2c_xfer_msg(struct i2c_adapter *adap, struct i2c_msg *msg,
 	dev_dbg(i2c->dev, "addr: 0x%04x, len: %d, flags: 0x%x, stop: %d\n",
 		msg->addr, msg->len, msg->flags, stop);
 
-	if (msg->len == 0)
-		return -EINVAL;
-
 	/*
 	 * The MX28 I2C IP block can only do PIO READ for transfer of to up
 	 * 4 bytes of length. The write transfer is not limited as it can use
@@ -683,6 +680,10 @@ static const struct i2c_algorithm mxs_i2c_algo = {
 	.functionality = mxs_i2c_func,
 };
 
+static const struct i2c_adapter_quirks mxs_i2c_quirks = {
+	.flags = I2C_AQ_NO_ZERO_LEN,
+};
+
 static void mxs_i2c_derive_timing(struct mxs_i2c_dev *i2c, uint32_t speed)
 {
 	/* The I2C block clock runs at 24MHz */
@@ -854,6 +855,7 @@ static int mxs_i2c_probe(struct platform_device *pdev)
 	strlcpy(adap->name, "MXS I2C adapter", sizeof(adap->name));
 	adap->owner = THIS_MODULE;
 	adap->algo = &mxs_i2c_algo;
+	adap->quirks = &mxs_i2c_quirks;
 	adap->dev.parent = dev;
 	adap->nr = pdev->id;
 	adap->dev.of_node = pdev->dev.of_node;
diff --git a/drivers/i2c/busses/i2c-owl.c b/drivers/i2c/busses/i2c-owl.c
new file mode 100644
index 000000000000..96b4572e6d9c
--- /dev/null
+++ b/drivers/i2c/busses/i2c-owl.c
@@ -0,0 +1,495 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Actions Semiconductor Owl SoC's I2C driver
+ *
+ * Copyright (c) 2014 Actions Semi Inc.
+ * Author: David Liu <liuwei@actions-semi.com>
+ *
+ * Copyright (c) 2018 Linaro Ltd.
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+
+/* I2C registers */
+#define OWL_I2C_REG_CTL		0x0000
+#define OWL_I2C_REG_CLKDIV	0x0004
+#define OWL_I2C_REG_STAT	0x0008
+#define OWL_I2C_REG_ADDR	0x000C
+#define OWL_I2C_REG_TXDAT	0x0010
+#define OWL_I2C_REG_RXDAT	0x0014
+#define OWL_I2C_REG_CMD		0x0018
+#define OWL_I2C_REG_FIFOCTL	0x001C
+#define OWL_I2C_REG_FIFOSTAT	0x0020
+#define OWL_I2C_REG_DATCNT	0x0024
+#define OWL_I2C_REG_RCNT	0x0028
+
+/* I2Cx_CTL Bit Mask */
+#define OWL_I2C_CTL_RB		BIT(1)
+#define OWL_I2C_CTL_GBCC(x)	(((x) & 0x3) << 2)
+#define	OWL_I2C_CTL_GBCC_NONE	OWL_I2C_CTL_GBCC(0)
+#define	OWL_I2C_CTL_GBCC_START	OWL_I2C_CTL_GBCC(1)
+#define	OWL_I2C_CTL_GBCC_STOP	OWL_I2C_CTL_GBCC(2)
+#define	OWL_I2C_CTL_GBCC_RSTART	OWL_I2C_CTL_GBCC(3)
+#define OWL_I2C_CTL_IRQE	BIT(5)
+#define OWL_I2C_CTL_EN		BIT(7)
+#define OWL_I2C_CTL_AE		BIT(8)
+#define OWL_I2C_CTL_SHSM	BIT(10)
+
+#define OWL_I2C_DIV_FACTOR(x)	((x) & 0xff)
+
+/* I2Cx_STAT Bit Mask */
+#define OWL_I2C_STAT_RACK	BIT(0)
+#define OWL_I2C_STAT_BEB	BIT(1)
+#define OWL_I2C_STAT_IRQP	BIT(2)
+#define OWL_I2C_STAT_LAB	BIT(3)
+#define OWL_I2C_STAT_STPD	BIT(4)
+#define OWL_I2C_STAT_STAD	BIT(5)
+#define OWL_I2C_STAT_BBB	BIT(6)
+#define OWL_I2C_STAT_TCB	BIT(7)
+#define OWL_I2C_STAT_LBST	BIT(8)
+#define OWL_I2C_STAT_SAMB	BIT(9)
+#define OWL_I2C_STAT_SRGC	BIT(10)
+
+/* I2Cx_CMD Bit Mask */
+#define OWL_I2C_CMD_SBE		BIT(0)
+#define OWL_I2C_CMD_RBE		BIT(4)
+#define OWL_I2C_CMD_DE		BIT(8)
+#define OWL_I2C_CMD_NS		BIT(9)
+#define OWL_I2C_CMD_SE		BIT(10)
+#define OWL_I2C_CMD_MSS		BIT(11)
+#define OWL_I2C_CMD_WRS		BIT(12)
+#define OWL_I2C_CMD_SECL	BIT(15)
+
+#define OWL_I2C_CMD_AS(x)	(((x) & 0x7) << 1)
+#define OWL_I2C_CMD_SAS(x)	(((x) & 0x7) << 5)
+
+/* I2Cx_FIFOCTL Bit Mask */
+#define OWL_I2C_FIFOCTL_NIB	BIT(0)
+#define OWL_I2C_FIFOCTL_RFR	BIT(1)
+#define OWL_I2C_FIFOCTL_TFR	BIT(2)
+
+/* I2Cc_FIFOSTAT Bit Mask */
+#define OWL_I2C_FIFOSTAT_RNB	BIT(1)
+#define OWL_I2C_FIFOSTAT_RFE	BIT(2)
+#define OWL_I2C_FIFOSTAT_TFF	BIT(5)
+#define OWL_I2C_FIFOSTAT_TFD	GENMASK(23, 16)
+#define OWL_I2C_FIFOSTAT_RFD	GENMASK(15, 8)
+
+/* I2C bus timeout */
+#define OWL_I2C_TIMEOUT		msecs_to_jiffies(4 * 1000)
+
+#define OWL_I2C_MAX_RETRIES	50
+
+#define OWL_I2C_DEF_SPEED_HZ	100000
+#define OWL_I2C_MAX_SPEED_HZ	400000
+
+struct owl_i2c_dev {
+	struct i2c_adapter	adap;
+	struct i2c_msg		*msg;
+	struct completion	msg_complete;
+	struct clk		*clk;
+	spinlock_t		lock;
+	void __iomem		*base;
+	unsigned long		clk_rate;
+	u32			bus_freq;
+	u32			msg_ptr;
+	int			err;
+};
+
+static void owl_i2c_update_reg(void __iomem *reg, unsigned int val, bool state)
+{
+	unsigned int regval;
+
+	regval = readl(reg);
+
+	if (state)
+		regval |= val;
+	else
+		regval &= ~val;
+
+	writel(regval, reg);
+}
+
+static void owl_i2c_reset(struct owl_i2c_dev *i2c_dev)
+{
+	owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
+			   OWL_I2C_CTL_EN, false);
+	mdelay(1);
+	owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
+			   OWL_I2C_CTL_EN, true);
+
+	/* Clear status registers */
+	writel(0, i2c_dev->base + OWL_I2C_REG_STAT);
+}
+
+static int owl_i2c_reset_fifo(struct owl_i2c_dev *i2c_dev)
+{
+	unsigned int val, timeout = 0;
+
+	/* Reset FIFO */
+	owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_FIFOCTL,
+			   OWL_I2C_FIFOCTL_RFR | OWL_I2C_FIFOCTL_TFR,
+			   true);
+
+	/* Wait 50ms for FIFO reset complete */
+	do {
+		val = readl(i2c_dev->base + OWL_I2C_REG_FIFOCTL);
+		if (!(val & (OWL_I2C_FIFOCTL_RFR | OWL_I2C_FIFOCTL_TFR)))
+			break;
+		usleep_range(500, 1000);
+	} while (timeout++ < OWL_I2C_MAX_RETRIES);
+
+	if (timeout > OWL_I2C_MAX_RETRIES) {
+		dev_err(&i2c_dev->adap.dev, "FIFO reset timeout\n");
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static void owl_i2c_set_freq(struct owl_i2c_dev *i2c_dev)
+{
+	unsigned int val;
+
+	val = DIV_ROUND_UP(i2c_dev->clk_rate, i2c_dev->bus_freq * 16);
+
+	/* Set clock divider factor */
+	writel(OWL_I2C_DIV_FACTOR(val), i2c_dev->base + OWL_I2C_REG_CLKDIV);
+}
+
+static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
+{
+	struct owl_i2c_dev *i2c_dev = _dev;
+	struct i2c_msg *msg = i2c_dev->msg;
+	unsigned long flags;
+	unsigned int stat, fifostat;
+
+	spin_lock_irqsave(&i2c_dev->lock, flags);
+
+	i2c_dev->err = 0;
+
+	/* Handle NACK from slave */
+	fifostat = readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT);
+	if (fifostat & OWL_I2C_FIFOSTAT_RNB) {
+		i2c_dev->err = -ENXIO;
+		goto stop;
+	}
+
+	/* Handle bus error */
+	stat = readl(i2c_dev->base + OWL_I2C_REG_STAT);
+	if (stat & OWL_I2C_STAT_BEB) {
+		i2c_dev->err = -EIO;
+		goto stop;
+	}
+
+	/* Handle FIFO read */
+	if (msg->flags & I2C_M_RD) {
+		while ((readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT) &
+			OWL_I2C_FIFOSTAT_RFE) && i2c_dev->msg_ptr < msg->len) {
+			msg->buf[i2c_dev->msg_ptr++] = readl(i2c_dev->base +
+							     OWL_I2C_REG_RXDAT);
+		}
+	} else {
+		/* Handle the remaining bytes which were not sent */
+		while (!(readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT) &
+			 OWL_I2C_FIFOSTAT_TFF) && i2c_dev->msg_ptr < msg->len) {
+			writel(msg->buf[i2c_dev->msg_ptr++],
+			       i2c_dev->base + OWL_I2C_REG_TXDAT);
+		}
+	}
+
+stop:
+	/* Clear pending interrupts */
+	owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_STAT,
+			   OWL_I2C_STAT_IRQP, true);
+
+	complete_all(&i2c_dev->msg_complete);
+	spin_unlock_irqrestore(&i2c_dev->lock, flags);
+
+	return IRQ_HANDLED;
+}
+
+static u32 owl_i2c_func(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+static int owl_i2c_check_bus_busy(struct i2c_adapter *adap)
+{
+	struct owl_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
+	unsigned long timeout;
+
+	/* Check for Bus busy */
+	timeout = jiffies + OWL_I2C_TIMEOUT;
+	while (readl(i2c_dev->base + OWL_I2C_REG_STAT) & OWL_I2C_STAT_BBB) {
+		if (time_after(jiffies, timeout)) {
+			dev_err(&adap->dev, "Bus busy timeout\n");
+			return -ETIMEDOUT;
+		}
+	}
+
+	return 0;
+}
+
+static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
+			       int num)
+{
+	struct owl_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
+	struct i2c_msg *msg;
+	unsigned long time_left, flags;
+	unsigned int i2c_cmd, val;
+	unsigned int addr;
+	int ret, idx;
+
+	spin_lock_irqsave(&i2c_dev->lock, flags);
+
+	/* Reset I2C controller */
+	owl_i2c_reset(i2c_dev);
+
+	/* Set bus frequency */
+	owl_i2c_set_freq(i2c_dev);
+
+	/*
+	 * Spinlock should be released before calling reset FIFO and
+	 * bus busy check since those functions may sleep
+	 */
+	spin_unlock_irqrestore(&i2c_dev->lock, flags);
+
+	/* Reset FIFO */
+	ret = owl_i2c_reset_fifo(i2c_dev);
+	if (ret)
+		goto unlocked_err_exit;
+
+	/* Check for bus busy */
+	ret = owl_i2c_check_bus_busy(adap);
+	if (ret)
+		goto unlocked_err_exit;
+
+	spin_lock_irqsave(&i2c_dev->lock, flags);
+
+	/* Check for Arbitration lost */
+	val = readl(i2c_dev->base + OWL_I2C_REG_STAT);
+	if (val & OWL_I2C_STAT_LAB) {
+		val &= ~OWL_I2C_STAT_LAB;
+		writel(val, i2c_dev->base + OWL_I2C_REG_STAT);
+		ret = -EAGAIN;
+		goto err_exit;
+	}
+
+	reinit_completion(&i2c_dev->msg_complete);
+
+	/* Enable I2C controller interrupt */
+	owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
+			   OWL_I2C_CTL_IRQE, true);
+
+	/*
+	 * Select: FIFO enable, Master mode, Stop enable, Data count enable,
+	 * Send start bit
+	 */
+	i2c_cmd = OWL_I2C_CMD_SECL | OWL_I2C_CMD_MSS | OWL_I2C_CMD_SE |
+		  OWL_I2C_CMD_NS | OWL_I2C_CMD_DE | OWL_I2C_CMD_SBE;
+
+	/* Handle repeated start condition */
+	if (num > 1) {
+		/* Set internal address length and enable repeated start */
+		i2c_cmd |= OWL_I2C_CMD_AS(msgs[0].len + 1) |
+			   OWL_I2C_CMD_SAS(1) | OWL_I2C_CMD_RBE;
+
+		/* Write slave address */
+		addr = i2c_8bit_addr_from_msg(&msgs[0]);
+		writel(addr, i2c_dev->base + OWL_I2C_REG_TXDAT);
+
+		/* Write internal register address */
+		for (idx = 0; idx < msgs[0].len; idx++)
+			writel(msgs[0].buf[idx],
+			       i2c_dev->base + OWL_I2C_REG_TXDAT);
+
+		msg = &msgs[1];
+	} else {
+		/* Set address length */
+		i2c_cmd |= OWL_I2C_CMD_AS(1);
+		msg = &msgs[0];
+	}
+
+	i2c_dev->msg = msg;
+	i2c_dev->msg_ptr = 0;
+
+	/* Set data count for the message */
+	writel(msg->len, i2c_dev->base + OWL_I2C_REG_DATCNT);
+
+	addr = i2c_8bit_addr_from_msg(msg);
+	writel(addr, i2c_dev->base + OWL_I2C_REG_TXDAT);
+
+	if (!(msg->flags & I2C_M_RD)) {
+		/* Write data to FIFO */
+		for (idx = 0; idx < msg->len; idx++) {
+			/* Check for FIFO full */
+			if (readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT) &
+			    OWL_I2C_FIFOSTAT_TFF)
+				break;
+
+			writel(msg->buf[idx],
+			       i2c_dev->base + OWL_I2C_REG_TXDAT);
+		}
+
+		i2c_dev->msg_ptr = idx;
+	}
+
+	/* Ignore the NACK if needed */
+	if (msg->flags & I2C_M_IGNORE_NAK)
+		owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_FIFOCTL,
+				   OWL_I2C_FIFOCTL_NIB, true);
+	else
+		owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_FIFOCTL,
+				   OWL_I2C_FIFOCTL_NIB, false);
+
+	/* Start the transfer */
+	writel(i2c_cmd, i2c_dev->base + OWL_I2C_REG_CMD);
+
+	spin_unlock_irqrestore(&i2c_dev->lock, flags);
+
+	time_left = wait_for_completion_timeout(&i2c_dev->msg_complete,
+						adap->timeout);
+
+	spin_lock_irqsave(&i2c_dev->lock, flags);
+	if (time_left == 0) {
+		dev_err(&adap->dev, "Transaction timed out\n");
+		/* Send stop condition and release the bus */
+		owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
+				   OWL_I2C_CTL_GBCC_STOP | OWL_I2C_CTL_RB,
+				   true);
+		ret = -ETIMEDOUT;
+		goto err_exit;
+	}
+
+	ret = i2c_dev->err < 0 ? i2c_dev->err : num;
+
+err_exit:
+	spin_unlock_irqrestore(&i2c_dev->lock, flags);
+
+unlocked_err_exit:
+	/* Disable I2C controller */
+	owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
+			   OWL_I2C_CTL_EN, false);
+
+	return ret;
+}
+
+static const struct i2c_algorithm owl_i2c_algorithm = {
+	.master_xfer    = owl_i2c_master_xfer,
+	.functionality  = owl_i2c_func,
+};
+
+static const struct i2c_adapter_quirks owl_i2c_quirks = {
+	.flags		= I2C_AQ_COMB | I2C_AQ_COMB_WRITE_FIRST,
+	.max_read_len   = 240,
+	.max_write_len  = 240,
+	.max_comb_1st_msg_len = 6,
+	.max_comb_2nd_msg_len = 240,
+};
+
+static int owl_i2c_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct owl_i2c_dev *i2c_dev;
+	struct resource *res;
+	int ret, irq;
+
+	i2c_dev = devm_kzalloc(dev, sizeof(*i2c_dev), GFP_KERNEL);
+	if (!i2c_dev)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	i2c_dev->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(i2c_dev->base))
+		return PTR_ERR(i2c_dev->base);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "failed to get IRQ number\n");
+		return irq;
+	}
+
+	if (of_property_read_u32(dev->of_node, "clock-frequency",
+				 &i2c_dev->bus_freq))
+		i2c_dev->bus_freq = OWL_I2C_DEF_SPEED_HZ;
+
+	/* We support only frequencies of 100k and 400k for now */
+	if (i2c_dev->bus_freq != OWL_I2C_DEF_SPEED_HZ &&
+	    i2c_dev->bus_freq != OWL_I2C_MAX_SPEED_HZ) {
+		dev_err(dev, "invalid clock-frequency %d\n", i2c_dev->bus_freq);
+		return -EINVAL;
+	}
+
+	i2c_dev->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(i2c_dev->clk)) {
+		dev_err(dev, "failed to get clock\n");
+		return PTR_ERR(i2c_dev->clk);
+	}
+
+	ret = clk_prepare_enable(i2c_dev->clk);
+	if (ret)
+		return ret;
+
+	i2c_dev->clk_rate = clk_get_rate(i2c_dev->clk);
+	if (!i2c_dev->clk_rate) {
+		dev_err(dev, "input clock rate should not be zero\n");
+		ret = -EINVAL;
+		goto disable_clk;
+	}
+
+	init_completion(&i2c_dev->msg_complete);
+	spin_lock_init(&i2c_dev->lock);
+	i2c_dev->adap.owner = THIS_MODULE;
+	i2c_dev->adap.algo = &owl_i2c_algorithm;
+	i2c_dev->adap.timeout = OWL_I2C_TIMEOUT;
+	i2c_dev->adap.quirks = &owl_i2c_quirks;
+	i2c_dev->adap.dev.parent = dev;
+	i2c_dev->adap.dev.of_node = dev->of_node;
+	snprintf(i2c_dev->adap.name, sizeof(i2c_dev->adap.name),
+		 "%s", "OWL I2C adapter");
+	i2c_set_adapdata(&i2c_dev->adap, i2c_dev);
+
+	platform_set_drvdata(pdev, i2c_dev);
+
+	ret = devm_request_irq(dev, irq, owl_i2c_interrupt, 0, pdev->name,
+			       i2c_dev);
+	if (ret) {
+		dev_err(dev, "failed to request irq %d\n", irq);
+		goto disable_clk;
+	}
+
+	return i2c_add_adapter(&i2c_dev->adap);
+
+disable_clk:
+	clk_disable_unprepare(i2c_dev->clk);
+
+	return ret;
+}
+
+static const struct of_device_id owl_i2c_of_match[] = {
+	{ .compatible = "actions,s900-i2c" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, owl_i2c_of_match);
+
+static struct platform_driver owl_i2c_driver = {
+	.probe		= owl_i2c_probe,
+	.driver		= {
+		.name	= "owl-i2c",
+		.of_match_table = of_match_ptr(owl_i2c_of_match),
+	},
+};
+module_platform_driver(owl_i2c_driver);
+
+MODULE_AUTHOR("David Liu <liuwei@actions-semi.com>");
+MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>");
+MODULE_DESCRIPTION("Actions Semiconductor Owl SoC's I2C driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/i2c/busses/i2c-pasemi.c b/drivers/i2c/busses/i2c-pasemi.c
index 55fd5c6f3cca..50803e5d995b 100644
--- a/drivers/i2c/busses/i2c-pasemi.c
+++ b/drivers/i2c/busses/i2c-pasemi.c
@@ -365,7 +365,6 @@ static int pasemi_smb_probe(struct pci_dev *dev,
 	smbus->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
 	smbus->adapter.algo = &smbus_algorithm;
 	smbus->adapter.algo_data = smbus;
-	smbus->adapter.nr = PCI_FUNC(dev->devfn);
 
 	/* set up the sysfs linkage to our parent device */
 	smbus->adapter.dev.parent = &dev->dev;
@@ -373,7 +372,7 @@ static int pasemi_smb_probe(struct pci_dev *dev,
 	reg_write(smbus, REG_CTL, (CTL_MTR | CTL_MRR |
 		  (CLK_100K_DIV & CTL_CLK_M)));
 
-	error = i2c_add_numbered_adapter(&smbus->adapter);
+	error = i2c_add_adapter(&smbus->adapter);
 	if (error)
 		goto out_release_region;
 
diff --git a/drivers/i2c/busses/i2c-pmcmsp.c b/drivers/i2c/busses/i2c-pmcmsp.c
index dae8ac618a52..0829cb696d9d 100644
--- a/drivers/i2c/busses/i2c-pmcmsp.c
+++ b/drivers/i2c/busses/i2c-pmcmsp.c
@@ -444,16 +444,6 @@ static enum pmcmsptwi_xfer_result pmcmsptwi_xfer_cmd(
 {
 	enum pmcmsptwi_xfer_result retval;
 
-	if ((cmd->type == MSP_TWI_CMD_WRITE && cmd->write_len == 0) ||
-	    (cmd->type == MSP_TWI_CMD_READ && cmd->read_len == 0) ||
-	    (cmd->type == MSP_TWI_CMD_WRITE_READ &&
-	    (cmd->read_len == 0 || cmd->write_len == 0))) {
-		dev_err(&pmcmsptwi_adapter.dev,
-			"%s: Cannot transfer less than 1 byte\n",
-			__func__);
-		return -EINVAL;
-	}
-
 	mutex_lock(&data->lock);
 	dev_dbg(&pmcmsptwi_adapter.dev,
 		"Setting address to 0x%04x\n", cmd->addr);
@@ -532,11 +522,6 @@ static int pmcmsptwi_master_xfer(struct i2c_adapter *adap,
 		cmd.write_data = msg->buf;
 	}
 
-	if (msg->len == 0) {
-		dev_err(&adap->dev, "Zero-byte messages unsupported\n");
-		return -EINVAL;
-	}
-
 	cmd.addr = msg->addr;
 
 	if (msg->flags & I2C_M_TEN) {
@@ -578,7 +563,7 @@ static u32 pmcmsptwi_i2c_func(struct i2c_adapter *adapter)
 }
 
 static const struct i2c_adapter_quirks pmcmsptwi_i2c_quirks = {
-	.flags = I2C_AQ_COMB_WRITE_THEN_READ,
+	.flags = I2C_AQ_COMB_WRITE_THEN_READ | I2C_AQ_NO_ZERO_LEN,
 	.max_write_len = MSP_MAX_BYTES_PER_RW,
 	.max_read_len = MSP_MAX_BYTES_PER_RW,
 	.max_comb_1st_msg_len = MSP_MAX_BYTES_PER_RW,
diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
new file mode 100644
index 000000000000..36732eb688a4
--- /dev/null
+++ b/drivers/i2c/busses/i2c-qcom-geni.c
@@ -0,0 +1,673 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017-2018, The Linux Foundation. All rights reserved.
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/qcom-geni-se.h>
+#include <linux/spinlock.h>
+
+#define SE_I2C_TX_TRANS_LEN		0x26c
+#define SE_I2C_RX_TRANS_LEN		0x270
+#define SE_I2C_SCL_COUNTERS		0x278
+
+#define SE_I2C_ERR  (M_CMD_OVERRUN_EN | M_ILLEGAL_CMD_EN | M_CMD_FAILURE_EN |\
+			M_GP_IRQ_1_EN | M_GP_IRQ_3_EN | M_GP_IRQ_4_EN)
+#define SE_I2C_ABORT		BIT(1)
+
+/* M_CMD OP codes for I2C */
+#define I2C_WRITE		0x1
+#define I2C_READ		0x2
+#define I2C_WRITE_READ		0x3
+#define I2C_ADDR_ONLY		0x4
+#define I2C_BUS_CLEAR		0x6
+#define I2C_STOP_ON_BUS		0x7
+/* M_CMD params for I2C */
+#define PRE_CMD_DELAY		BIT(0)
+#define TIMESTAMP_BEFORE	BIT(1)
+#define STOP_STRETCH		BIT(2)
+#define TIMESTAMP_AFTER		BIT(3)
+#define POST_COMMAND_DELAY	BIT(4)
+#define IGNORE_ADD_NACK		BIT(6)
+#define READ_FINISHED_WITH_ACK	BIT(7)
+#define BYPASS_ADDR_PHASE	BIT(8)
+#define SLV_ADDR_MSK		GENMASK(15, 9)
+#define SLV_ADDR_SHFT		9
+/* I2C SCL COUNTER fields */
+#define HIGH_COUNTER_MSK	GENMASK(29, 20)
+#define HIGH_COUNTER_SHFT	20
+#define LOW_COUNTER_MSK		GENMASK(19, 10)
+#define LOW_COUNTER_SHFT	10
+#define CYCLE_COUNTER_MSK	GENMASK(9, 0)
+
+enum geni_i2c_err_code {
+	GP_IRQ0,
+	NACK,
+	GP_IRQ2,
+	BUS_PROTO,
+	ARB_LOST,
+	GP_IRQ5,
+	GENI_OVERRUN,
+	GENI_ILLEGAL_CMD,
+	GENI_ABORT_DONE,
+	GENI_TIMEOUT,
+};
+
+#define DM_I2C_CB_ERR		((BIT(NACK) | BIT(BUS_PROTO) | BIT(ARB_LOST)) \
+									<< 5)
+
+#define I2C_AUTO_SUSPEND_DELAY	250
+#define KHZ(freq)		(1000 * freq)
+#define PACKING_BYTES_PW	4
+
+#define ABORT_TIMEOUT		HZ
+#define XFER_TIMEOUT		HZ
+#define RST_TIMEOUT		HZ
+
+struct geni_i2c_dev {
+	struct geni_se se;
+	u32 tx_wm;
+	int irq;
+	int err;
+	struct i2c_adapter adap;
+	struct completion done;
+	struct i2c_msg *cur;
+	int cur_wr;
+	int cur_rd;
+	spinlock_t lock;
+	u32 clk_freq_out;
+	const struct geni_i2c_clk_fld *clk_fld;
+	int suspended;
+};
+
+struct geni_i2c_err_log {
+	int err;
+	const char *msg;
+};
+
+static const struct geni_i2c_err_log gi2c_log[] = {
+	[GP_IRQ0] = {-EIO, "Unknown I2C err GP_IRQ0"},
+	[NACK] = {-ENXIO, "NACK: slv unresponsive, check its power/reset-ln"},
+	[GP_IRQ2] = {-EIO, "Unknown I2C err GP IRQ2"},
+	[BUS_PROTO] = {-EPROTO, "Bus proto err, noisy/unepxected start/stop"},
+	[ARB_LOST] = {-EAGAIN, "Bus arbitration lost, clock line undriveable"},
+	[GP_IRQ5] = {-EIO, "Unknown I2C err GP IRQ5"},
+	[GENI_OVERRUN] = {-EIO, "Cmd overrun, check GENI cmd-state machine"},
+	[GENI_ILLEGAL_CMD] = {-EIO, "Illegal cmd, check GENI cmd-state machine"},
+	[GENI_ABORT_DONE] = {-ETIMEDOUT, "Abort after timeout successful"},
+	[GENI_TIMEOUT] = {-ETIMEDOUT, "I2C TXN timed out"},
+};
+
+struct geni_i2c_clk_fld {
+	u32	clk_freq_out;
+	u8	clk_div;
+	u8	t_high_cnt;
+	u8	t_low_cnt;
+	u8	t_cycle_cnt;
+};
+
+/*
+ * Hardware uses the underlying formula to calculate time periods of
+ * SCL clock cycle. Firmware uses some additional cycles excluded from the
+ * below formula and it is confirmed that the time periods are within
+ * specification limits.
+ *
+ * time of high period of SCL: t_high = (t_high_cnt * clk_div) / source_clock
+ * time of low period of SCL: t_low = (t_low_cnt * clk_div) / source_clock
+ * time of full period of SCL: t_cycle = (t_cycle_cnt * clk_div) / source_clock
+ * clk_freq_out = t / t_cycle
+ * source_clock = 19.2 MHz
+ */
+static const struct geni_i2c_clk_fld geni_i2c_clk_map[] = {
+	{KHZ(100), 7, 10, 11, 26},
+	{KHZ(400), 2,  5, 12, 24},
+	{KHZ(1000), 1, 3,  9, 18},
+};
+
+static int geni_i2c_clk_map_idx(struct geni_i2c_dev *gi2c)
+{
+	int i;
+	const struct geni_i2c_clk_fld *itr = geni_i2c_clk_map;
+
+	for (i = 0; i < ARRAY_SIZE(geni_i2c_clk_map); i++, itr++) {
+		if (itr->clk_freq_out == gi2c->clk_freq_out) {
+			gi2c->clk_fld = itr;
+			return 0;
+		}
+	}
+	return -EINVAL;
+}
+
+static void qcom_geni_i2c_conf(struct geni_i2c_dev *gi2c)
+{
+	const struct geni_i2c_clk_fld *itr = gi2c->clk_fld;
+	u32 val;
+
+	writel_relaxed(0, gi2c->se.base + SE_GENI_CLK_SEL);
+
+	val = (itr->clk_div << CLK_DIV_SHFT) | SER_CLK_EN;
+	writel_relaxed(val, gi2c->se.base + GENI_SER_M_CLK_CFG);
+
+	val = itr->t_high_cnt << HIGH_COUNTER_SHFT;
+	val |= itr->t_low_cnt << LOW_COUNTER_SHFT;
+	val |= itr->t_cycle_cnt;
+	writel_relaxed(val, gi2c->se.base + SE_I2C_SCL_COUNTERS);
+}
+
+static void geni_i2c_err_misc(struct geni_i2c_dev *gi2c)
+{
+	u32 m_cmd = readl_relaxed(gi2c->se.base + SE_GENI_M_CMD0);
+	u32 m_stat = readl_relaxed(gi2c->se.base + SE_GENI_M_IRQ_STATUS);
+	u32 geni_s = readl_relaxed(gi2c->se.base + SE_GENI_STATUS);
+	u32 geni_ios = readl_relaxed(gi2c->se.base + SE_GENI_IOS);
+	u32 dma = readl_relaxed(gi2c->se.base + SE_GENI_DMA_MODE_EN);
+	u32 rx_st, tx_st;
+
+	if (dma) {
+		rx_st = readl_relaxed(gi2c->se.base + SE_DMA_RX_IRQ_STAT);
+		tx_st = readl_relaxed(gi2c->se.base + SE_DMA_TX_IRQ_STAT);
+	} else {
+		rx_st = readl_relaxed(gi2c->se.base + SE_GENI_RX_FIFO_STATUS);
+		tx_st = readl_relaxed(gi2c->se.base + SE_GENI_TX_FIFO_STATUS);
+	}
+	dev_dbg(gi2c->se.dev, "DMA:%d tx_stat:0x%x, rx_stat:0x%x, irq-stat:0x%x\n",
+		dma, tx_st, rx_st, m_stat);
+	dev_dbg(gi2c->se.dev, "m_cmd:0x%x, geni_status:0x%x, geni_ios:0x%x\n",
+		m_cmd, geni_s, geni_ios);
+}
+
+static void geni_i2c_err(struct geni_i2c_dev *gi2c, int err)
+{
+	if (!gi2c->err)
+		gi2c->err = gi2c_log[err].err;
+	if (gi2c->cur)
+		dev_dbg(gi2c->se.dev, "len:%d, slv-addr:0x%x, RD/WR:%d\n",
+			gi2c->cur->len, gi2c->cur->addr, gi2c->cur->flags);
+
+	if (err != NACK && err != GENI_ABORT_DONE) {
+		dev_err(gi2c->se.dev, "%s\n", gi2c_log[err].msg);
+		geni_i2c_err_misc(gi2c);
+	}
+}
+
+static irqreturn_t geni_i2c_irq(int irq, void *dev)
+{
+	struct geni_i2c_dev *gi2c = dev;
+	int j;
+	u32 m_stat;
+	u32 rx_st;
+	u32 dm_tx_st;
+	u32 dm_rx_st;
+	u32 dma;
+	struct i2c_msg *cur;
+	unsigned long flags;
+
+	spin_lock_irqsave(&gi2c->lock, flags);
+	m_stat = readl_relaxed(gi2c->se.base + SE_GENI_M_IRQ_STATUS);
+	rx_st = readl_relaxed(gi2c->se.base + SE_GENI_RX_FIFO_STATUS);
+	dm_tx_st = readl_relaxed(gi2c->se.base + SE_DMA_TX_IRQ_STAT);
+	dm_rx_st = readl_relaxed(gi2c->se.base + SE_DMA_RX_IRQ_STAT);
+	dma = readl_relaxed(gi2c->se.base + SE_GENI_DMA_MODE_EN);
+	cur = gi2c->cur;
+
+	if (!cur ||
+	    m_stat & (M_CMD_FAILURE_EN | M_CMD_ABORT_EN) ||
+	    dm_rx_st & (DM_I2C_CB_ERR)) {
+		if (m_stat & M_GP_IRQ_1_EN)
+			geni_i2c_err(gi2c, NACK);
+		if (m_stat & M_GP_IRQ_3_EN)
+			geni_i2c_err(gi2c, BUS_PROTO);
+		if (m_stat & M_GP_IRQ_4_EN)
+			geni_i2c_err(gi2c, ARB_LOST);
+		if (m_stat & M_CMD_OVERRUN_EN)
+			geni_i2c_err(gi2c, GENI_OVERRUN);
+		if (m_stat & M_ILLEGAL_CMD_EN)
+			geni_i2c_err(gi2c, GENI_ILLEGAL_CMD);
+		if (m_stat & M_CMD_ABORT_EN)
+			geni_i2c_err(gi2c, GENI_ABORT_DONE);
+		if (m_stat & M_GP_IRQ_0_EN)
+			geni_i2c_err(gi2c, GP_IRQ0);
+
+		/* Disable the TX Watermark interrupt to stop TX */
+		if (!dma)
+			writel_relaxed(0, gi2c->se.base +
+					   SE_GENI_TX_WATERMARK_REG);
+		goto irqret;
+	}
+
+	if (dma) {
+		dev_dbg(gi2c->se.dev, "i2c dma tx:0x%x, dma rx:0x%x\n",
+			dm_tx_st, dm_rx_st);
+		goto irqret;
+	}
+
+	if (cur->flags & I2C_M_RD &&
+	    m_stat & (M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN)) {
+		u32 rxcnt = rx_st & RX_FIFO_WC_MSK;
+
+		for (j = 0; j < rxcnt; j++) {
+			u32 val;
+			int p = 0;
+
+			val = readl_relaxed(gi2c->se.base + SE_GENI_RX_FIFOn);
+			while (gi2c->cur_rd < cur->len && p < sizeof(val)) {
+				cur->buf[gi2c->cur_rd++] = val & 0xff;
+				val >>= 8;
+				p++;
+			}
+			if (gi2c->cur_rd == cur->len)
+				break;
+		}
+	} else if (!(cur->flags & I2C_M_RD) &&
+		   m_stat & M_TX_FIFO_WATERMARK_EN) {
+		for (j = 0; j < gi2c->tx_wm; j++) {
+			u32 temp;
+			u32 val = 0;
+			int p = 0;
+
+			while (gi2c->cur_wr < cur->len && p < sizeof(val)) {
+				temp = cur->buf[gi2c->cur_wr++];
+				val |= temp << (p * 8);
+				p++;
+			}
+			writel_relaxed(val, gi2c->se.base + SE_GENI_TX_FIFOn);
+			/* TX Complete, Disable the TX Watermark interrupt */
+			if (gi2c->cur_wr == cur->len) {
+				writel_relaxed(0, gi2c->se.base +
+						SE_GENI_TX_WATERMARK_REG);
+				break;
+			}
+		}
+	}
+irqret:
+	if (m_stat)
+		writel_relaxed(m_stat, gi2c->se.base + SE_GENI_M_IRQ_CLEAR);
+
+	if (dma) {
+		if (dm_tx_st)
+			writel_relaxed(dm_tx_st, gi2c->se.base +
+						SE_DMA_TX_IRQ_CLR);
+		if (dm_rx_st)
+			writel_relaxed(dm_rx_st, gi2c->se.base +
+						SE_DMA_RX_IRQ_CLR);
+	}
+	/* if this is err with done-bit not set, handle that through timeout. */
+	if (m_stat & M_CMD_DONE_EN || m_stat & M_CMD_ABORT_EN)
+		complete(&gi2c->done);
+	else if (dm_tx_st & TX_DMA_DONE || dm_tx_st & TX_RESET_DONE)
+		complete(&gi2c->done);
+	else if (dm_rx_st & RX_DMA_DONE || dm_rx_st & RX_RESET_DONE)
+		complete(&gi2c->done);
+
+	spin_unlock_irqrestore(&gi2c->lock, flags);
+	return IRQ_HANDLED;
+}
+
+static void geni_i2c_abort_xfer(struct geni_i2c_dev *gi2c)
+{
+	u32 val;
+	unsigned long time_left = ABORT_TIMEOUT;
+	unsigned long flags;
+
+	spin_lock_irqsave(&gi2c->lock, flags);
+	geni_i2c_err(gi2c, GENI_TIMEOUT);
+	gi2c->cur = NULL;
+	geni_se_abort_m_cmd(&gi2c->se);
+	spin_unlock_irqrestore(&gi2c->lock, flags);
+	do {
+		time_left = wait_for_completion_timeout(&gi2c->done, time_left);
+		val = readl_relaxed(gi2c->se.base + SE_GENI_M_IRQ_STATUS);
+	} while (!(val & M_CMD_ABORT_EN) && time_left);
+
+	if (!(val & M_CMD_ABORT_EN))
+		dev_err(gi2c->se.dev, "Timeout abort_m_cmd\n");
+}
+
+static void geni_i2c_rx_fsm_rst(struct geni_i2c_dev *gi2c)
+{
+	u32 val;
+	unsigned long time_left = RST_TIMEOUT;
+
+	writel_relaxed(1, gi2c->se.base + SE_DMA_RX_FSM_RST);
+	do {
+		time_left = wait_for_completion_timeout(&gi2c->done, time_left);
+		val = readl_relaxed(gi2c->se.base + SE_DMA_RX_IRQ_STAT);
+	} while (!(val & RX_RESET_DONE) && time_left);
+
+	if (!(val & RX_RESET_DONE))
+		dev_err(gi2c->se.dev, "Timeout resetting RX_FSM\n");
+}
+
+static void geni_i2c_tx_fsm_rst(struct geni_i2c_dev *gi2c)
+{
+	u32 val;
+	unsigned long time_left = RST_TIMEOUT;
+
+	writel_relaxed(1, gi2c->se.base + SE_DMA_TX_FSM_RST);
+	do {
+		time_left = wait_for_completion_timeout(&gi2c->done, time_left);
+		val = readl_relaxed(gi2c->se.base + SE_DMA_TX_IRQ_STAT);
+	} while (!(val & TX_RESET_DONE) && time_left);
+
+	if (!(val & TX_RESET_DONE))
+		dev_err(gi2c->se.dev, "Timeout resetting TX_FSM\n");
+}
+
+static int geni_i2c_rx_one_msg(struct geni_i2c_dev *gi2c, struct i2c_msg *msg,
+				u32 m_param)
+{
+	dma_addr_t rx_dma;
+	enum geni_se_xfer_mode mode;
+	unsigned long time_left = XFER_TIMEOUT;
+
+	gi2c->cur = msg;
+	mode = msg->len > 32 ? GENI_SE_DMA : GENI_SE_FIFO;
+	geni_se_select_mode(&gi2c->se, mode);
+	writel_relaxed(msg->len, gi2c->se.base + SE_I2C_RX_TRANS_LEN);
+	geni_se_setup_m_cmd(&gi2c->se, I2C_READ, m_param);
+	if (mode == GENI_SE_DMA) {
+		int ret;
+
+		ret = geni_se_rx_dma_prep(&gi2c->se, msg->buf, msg->len,
+								&rx_dma);
+		if (ret) {
+			mode = GENI_SE_FIFO;
+			geni_se_select_mode(&gi2c->se, mode);
+		}
+	}
+
+	time_left = wait_for_completion_timeout(&gi2c->done, XFER_TIMEOUT);
+	if (!time_left)
+		geni_i2c_abort_xfer(gi2c);
+
+	gi2c->cur_rd = 0;
+	if (mode == GENI_SE_DMA) {
+		if (gi2c->err)
+			geni_i2c_rx_fsm_rst(gi2c);
+		geni_se_rx_dma_unprep(&gi2c->se, rx_dma, msg->len);
+	}
+	return gi2c->err;
+}
+
+static int geni_i2c_tx_one_msg(struct geni_i2c_dev *gi2c, struct i2c_msg *msg,
+				u32 m_param)
+{
+	dma_addr_t tx_dma;
+	enum geni_se_xfer_mode mode;
+	unsigned long time_left;
+
+	gi2c->cur = msg;
+	mode = msg->len > 32 ? GENI_SE_DMA : GENI_SE_FIFO;
+	geni_se_select_mode(&gi2c->se, mode);
+	writel_relaxed(msg->len, gi2c->se.base + SE_I2C_TX_TRANS_LEN);
+	geni_se_setup_m_cmd(&gi2c->se, I2C_WRITE, m_param);
+	if (mode == GENI_SE_DMA) {
+		int ret;
+
+		ret = geni_se_tx_dma_prep(&gi2c->se, msg->buf, msg->len,
+								&tx_dma);
+		if (ret) {
+			mode = GENI_SE_FIFO;
+			geni_se_select_mode(&gi2c->se, mode);
+		}
+	}
+
+	if (mode == GENI_SE_FIFO) /* Get FIFO IRQ */
+		writel_relaxed(1, gi2c->se.base + SE_GENI_TX_WATERMARK_REG);
+
+	time_left = wait_for_completion_timeout(&gi2c->done, XFER_TIMEOUT);
+	if (!time_left)
+		geni_i2c_abort_xfer(gi2c);
+
+	gi2c->cur_wr = 0;
+	if (mode == GENI_SE_DMA) {
+		if (gi2c->err)
+			geni_i2c_tx_fsm_rst(gi2c);
+		geni_se_tx_dma_unprep(&gi2c->se, tx_dma, msg->len);
+	}
+	return gi2c->err;
+}
+
+static int geni_i2c_xfer(struct i2c_adapter *adap,
+			 struct i2c_msg msgs[],
+			 int num)
+{
+	struct geni_i2c_dev *gi2c = i2c_get_adapdata(adap);
+	int i, ret;
+
+	gi2c->err = 0;
+	reinit_completion(&gi2c->done);
+	ret = pm_runtime_get_sync(gi2c->se.dev);
+	if (ret < 0) {
+		dev_err(gi2c->se.dev, "error turning SE resources:%d\n", ret);
+		pm_runtime_put_noidle(gi2c->se.dev);
+		/* Set device in suspended since resume failed */
+		pm_runtime_set_suspended(gi2c->se.dev);
+		return ret;
+	}
+
+	qcom_geni_i2c_conf(gi2c);
+	for (i = 0; i < num; i++) {
+		u32 m_param = i < (num - 1) ? STOP_STRETCH : 0;
+
+		m_param |= ((msgs[i].addr << SLV_ADDR_SHFT) & SLV_ADDR_MSK);
+
+		if (msgs[i].flags & I2C_M_RD)
+			ret = geni_i2c_rx_one_msg(gi2c, &msgs[i], m_param);
+		else
+			ret = geni_i2c_tx_one_msg(gi2c, &msgs[i], m_param);
+
+		if (ret)
+			break;
+	}
+	if (ret == 0)
+		ret = num;
+
+	pm_runtime_mark_last_busy(gi2c->se.dev);
+	pm_runtime_put_autosuspend(gi2c->se.dev);
+	gi2c->cur = NULL;
+	gi2c->err = 0;
+	return ret;
+}
+
+static u32 geni_i2c_func(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
+}
+
+static const struct i2c_algorithm geni_i2c_algo = {
+	.master_xfer	= geni_i2c_xfer,
+	.functionality	= geni_i2c_func,
+};
+
+static int geni_i2c_probe(struct platform_device *pdev)
+{
+	struct geni_i2c_dev *gi2c;
+	struct resource *res;
+	u32 proto, tx_depth;
+	int ret;
+
+	gi2c = devm_kzalloc(&pdev->dev, sizeof(*gi2c), GFP_KERNEL);
+	if (!gi2c)
+		return -ENOMEM;
+
+	gi2c->se.dev = &pdev->dev;
+	gi2c->se.wrapper = dev_get_drvdata(pdev->dev.parent);
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	gi2c->se.base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(gi2c->se.base))
+		return PTR_ERR(gi2c->se.base);
+
+	gi2c->se.clk = devm_clk_get(&pdev->dev, "se");
+	if (IS_ERR(gi2c->se.clk)) {
+		ret = PTR_ERR(gi2c->se.clk);
+		dev_err(&pdev->dev, "Err getting SE Core clk %d\n", ret);
+		return ret;
+	}
+
+	ret = device_property_read_u32(&pdev->dev, "clock-frequency",
+							&gi2c->clk_freq_out);
+	if (ret) {
+		dev_info(&pdev->dev,
+			"Bus frequency not specified, default to 100kHz.\n");
+		gi2c->clk_freq_out = KHZ(100);
+	}
+
+	gi2c->irq = platform_get_irq(pdev, 0);
+	if (gi2c->irq < 0) {
+		dev_err(&pdev->dev, "IRQ error for i2c-geni\n");
+		return gi2c->irq;
+	}
+
+	ret = geni_i2c_clk_map_idx(gi2c);
+	if (ret) {
+		dev_err(&pdev->dev, "Invalid clk frequency %d Hz: %d\n",
+			gi2c->clk_freq_out, ret);
+		return ret;
+	}
+
+	gi2c->adap.algo = &geni_i2c_algo;
+	init_completion(&gi2c->done);
+	spin_lock_init(&gi2c->lock);
+	platform_set_drvdata(pdev, gi2c);
+	ret = devm_request_irq(&pdev->dev, gi2c->irq, geni_i2c_irq,
+			       IRQF_TRIGGER_HIGH, "i2c_geni", gi2c);
+	if (ret) {
+		dev_err(&pdev->dev, "Request_irq failed:%d: err:%d\n",
+			gi2c->irq, ret);
+		return ret;
+	}
+	/* Disable the interrupt so that the system can enter low-power mode */
+	disable_irq(gi2c->irq);
+	i2c_set_adapdata(&gi2c->adap, gi2c);
+	gi2c->adap.dev.parent = &pdev->dev;
+	gi2c->adap.dev.of_node = pdev->dev.of_node;
+	strlcpy(gi2c->adap.name, "Geni-I2C", sizeof(gi2c->adap.name));
+
+	ret = geni_se_resources_on(&gi2c->se);
+	if (ret) {
+		dev_err(&pdev->dev, "Error turning on resources %d\n", ret);
+		return ret;
+	}
+	proto = geni_se_read_proto(&gi2c->se);
+	tx_depth = geni_se_get_tx_fifo_depth(&gi2c->se);
+	if (proto != GENI_SE_I2C) {
+		dev_err(&pdev->dev, "Invalid proto %d\n", proto);
+		geni_se_resources_off(&gi2c->se);
+		return -ENXIO;
+	}
+	gi2c->tx_wm = tx_depth - 1;
+	geni_se_init(&gi2c->se, gi2c->tx_wm, tx_depth);
+	geni_se_config_packing(&gi2c->se, BITS_PER_BYTE, PACKING_BYTES_PW,
+							true, true, true);
+	ret = geni_se_resources_off(&gi2c->se);
+	if (ret) {
+		dev_err(&pdev->dev, "Error turning off resources %d\n", ret);
+		return ret;
+	}
+
+	dev_dbg(&pdev->dev, "i2c fifo/se-dma mode. fifo depth:%d\n", tx_depth);
+
+	ret = i2c_add_adapter(&gi2c->adap);
+	if (ret) {
+		dev_err(&pdev->dev, "Error adding i2c adapter %d\n", ret);
+		return ret;
+	}
+
+	gi2c->suspended = 1;
+	pm_runtime_set_suspended(gi2c->se.dev);
+	pm_runtime_set_autosuspend_delay(gi2c->se.dev, I2C_AUTO_SUSPEND_DELAY);
+	pm_runtime_use_autosuspend(gi2c->se.dev);
+	pm_runtime_enable(gi2c->se.dev);
+
+	return 0;
+}
+
+static int geni_i2c_remove(struct platform_device *pdev)
+{
+	struct geni_i2c_dev *gi2c = platform_get_drvdata(pdev);
+
+	pm_runtime_disable(gi2c->se.dev);
+	i2c_del_adapter(&gi2c->adap);
+	return 0;
+}
+
+static int __maybe_unused geni_i2c_runtime_suspend(struct device *dev)
+{
+	int ret;
+	struct geni_i2c_dev *gi2c = dev_get_drvdata(dev);
+
+	disable_irq(gi2c->irq);
+	ret = geni_se_resources_off(&gi2c->se);
+	if (ret) {
+		enable_irq(gi2c->irq);
+		return ret;
+
+	} else {
+		gi2c->suspended = 1;
+	}
+
+	return 0;
+}
+
+static int __maybe_unused geni_i2c_runtime_resume(struct device *dev)
+{
+	int ret;
+	struct geni_i2c_dev *gi2c = dev_get_drvdata(dev);
+
+	ret = geni_se_resources_on(&gi2c->se);
+	if (ret)
+		return ret;
+
+	enable_irq(gi2c->irq);
+	gi2c->suspended = 0;
+	return 0;
+}
+
+static int __maybe_unused geni_i2c_suspend_noirq(struct device *dev)
+{
+	struct geni_i2c_dev *gi2c = dev_get_drvdata(dev);
+
+	if (!gi2c->suspended) {
+		geni_i2c_runtime_suspend(dev);
+		pm_runtime_disable(dev);
+		pm_runtime_set_suspended(dev);
+		pm_runtime_enable(dev);
+	}
+	return 0;
+}
+
+static const struct dev_pm_ops geni_i2c_pm_ops = {
+	SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(geni_i2c_suspend_noirq, NULL)
+	SET_RUNTIME_PM_OPS(geni_i2c_runtime_suspend, geni_i2c_runtime_resume,
+									NULL)
+};
+
+static const struct of_device_id geni_i2c_dt_match[] = {
+	{ .compatible = "qcom,geni-i2c" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, geni_i2c_dt_match);
+
+static struct platform_driver geni_i2c_driver = {
+	.probe  = geni_i2c_probe,
+	.remove = geni_i2c_remove,
+	.driver = {
+		.name = "geni_i2c",
+		.pm = &geni_i2c_pm_ops,
+		.of_match_table = geni_i2c_dt_match,
+	},
+};
+
+module_platform_driver(geni_i2c_driver);
+
+MODULE_DESCRIPTION("I2C Controller Driver for GENI based QUP cores");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/i2c/busses/i2c-rcar.c b/drivers/i2c/busses/i2c-rcar.c
index 3c1c817f6968..43ad933df0f0 100644
--- a/drivers/i2c/busses/i2c-rcar.c
+++ b/drivers/i2c/busses/i2c-rcar.c
@@ -19,6 +19,7 @@
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  */
+#include <linux/bitops.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/dmaengine.h>
@@ -112,9 +113,10 @@
 #define ID_ARBLOST	(1 << 3)
 #define ID_NACK		(1 << 4)
 /* persistent flags */
-#define ID_P_NO_RXDMA	(1 << 30) /* HW forbids RXDMA sometimes */
-#define ID_P_PM_BLOCKED	(1 << 31)
-#define ID_P_MASK	(ID_P_PM_BLOCKED | ID_P_NO_RXDMA)
+#define ID_P_REP_AFTER_RD	BIT(29)
+#define ID_P_NO_RXDMA		BIT(30) /* HW forbids RXDMA sometimes */
+#define ID_P_PM_BLOCKED		BIT(31)
+#define ID_P_MASK		GENMASK(31, 29)
 
 enum rcar_i2c_type {
 	I2C_RCAR_GEN1,
@@ -183,8 +185,6 @@ static void rcar_i2c_set_scl(struct i2c_adapter *adap, int val)
 	rcar_i2c_write(priv, ICMCR, priv->recovery_icmcr);
 };
 
-/* No get_sda, because the HW only reports its bus free logic, not SDA itself */
-
 static void rcar_i2c_set_sda(struct i2c_adapter *adap, int val)
 {
 	struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
@@ -197,10 +197,19 @@ static void rcar_i2c_set_sda(struct i2c_adapter *adap, int val)
 	rcar_i2c_write(priv, ICMCR, priv->recovery_icmcr);
 };
 
+static int rcar_i2c_get_bus_free(struct i2c_adapter *adap)
+{
+	struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	return !(rcar_i2c_read(priv, ICMCR) & FSDA);
+
+};
+
 static struct i2c_bus_recovery_info rcar_i2c_bri = {
 	.get_scl = rcar_i2c_get_scl,
 	.set_scl = rcar_i2c_set_scl,
 	.set_sda = rcar_i2c_set_sda,
+	.get_bus_free = rcar_i2c_get_bus_free,
 	.recover_bus = i2c_generic_scl_recovery,
 };
 static void rcar_i2c_init(struct rcar_i2c_priv *priv)
@@ -215,7 +224,7 @@ static void rcar_i2c_init(struct rcar_i2c_priv *priv)
 
 static int rcar_i2c_bus_barrier(struct rcar_i2c_priv *priv)
 {
-	int i, ret;
+	int i;
 
 	for (i = 0; i < LOOP_TIMEOUT; i++) {
 		/* make sure that bus is not busy */
@@ -226,13 +235,7 @@ static int rcar_i2c_bus_barrier(struct rcar_i2c_priv *priv)
 
 	/* Waiting did not help, try to recover */
 	priv->recovery_icmcr = MDBS | OBPC | FSDA | FSCL;
-	ret = i2c_recover_bus(&priv->adap);
-
-	/* No failure when recovering, so check bus busy bit again */
-	if (ret == 0)
-		ret = (rcar_i2c_read(priv, ICMCR) & FSDA) ? -EBUSY : 0;
-
-	return ret;
+	return i2c_recover_bus(&priv->adap);
 }
 
 static int rcar_i2c_clock_calculate(struct rcar_i2c_priv *priv, struct i2c_timings *t)
@@ -343,7 +346,10 @@ static void rcar_i2c_prepare_msg(struct rcar_i2c_priv *priv)
 		rcar_i2c_write(priv, ICMSR, 0);
 		rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START);
 	} else {
-		rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START);
+		if (priv->flags & ID_P_REP_AFTER_RD)
+			priv->flags &= ~ID_P_REP_AFTER_RD;
+		else
+			rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START);
 		rcar_i2c_write(priv, ICMSR, 0);
 	}
 	rcar_i2c_write(priv, ICMIER, read ? RCAR_IRQ_RECV : RCAR_IRQ_SEND);
@@ -548,15 +554,15 @@ static void rcar_i2c_irq_recv(struct rcar_i2c_priv *priv, u32 msr)
 		priv->pos++;
 	}
 
-	/*
-	 * If next received data is the _LAST_, go to STOP phase. Might be
-	 * overwritten by REP START when setting up a new msg. Not elegant
-	 * but the only stable sequence for REP START I have found so far.
-	 * If you want to change this code, make sure sending one transfer with
-	 * four messages (WR-RD-WR-RD) works!
-	 */
-	if (priv->pos + 1 >= msg->len)
-		rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP);
+	/* If next received data is the _LAST_, go to new phase. */
+	if (priv->pos + 1 == msg->len) {
+		if (priv->flags & ID_LAST_MSG) {
+			rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP);
+		} else {
+			rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START);
+			priv->flags |= ID_P_REP_AFTER_RD;
+		}
+	}
 
 	if (priv->pos == msg->len && !(priv->flags & ID_LAST_MSG))
 		rcar_i2c_next_msg(priv);
@@ -624,9 +630,11 @@ static irqreturn_t rcar_i2c_irq(int irq, void *ptr)
 	struct rcar_i2c_priv *priv = ptr;
 	u32 msr, val;
 
-	/* Clear START or STOP as soon as we can */
-	val = rcar_i2c_read(priv, ICMCR);
-	rcar_i2c_write(priv, ICMCR, val & RCAR_BUS_MASK_DATA);
+	/* Clear START or STOP immediately, except for REPSTART after read */
+	if (likely(!(priv->flags & ID_P_REP_AFTER_RD))) {
+		val = rcar_i2c_read(priv, ICMCR);
+		rcar_i2c_write(priv, ICMCR, val & RCAR_BUS_MASK_DATA);
+	}
 
 	msr = rcar_i2c_read(priv, ICMSR);
 
@@ -795,14 +803,8 @@ static int rcar_i2c_master_xfer(struct i2c_adapter *adap,
 	if (ret < 0)
 		goto out;
 
-	for (i = 0; i < num; i++) {
-		/* This HW can't send STOP after address phase */
-		if (msgs[i].len == 0) {
-			ret = -EOPNOTSUPP;
-			goto out;
-		}
+	for (i = 0; i < num; i++)
 		rcar_i2c_request_dma(priv, msgs + i);
-	}
 
 	/* init first message */
 	priv->msg = msgs;
@@ -889,6 +891,10 @@ static const struct i2c_algorithm rcar_i2c_algo = {
 	.unreg_slave	= rcar_unreg_slave,
 };
 
+static const struct i2c_adapter_quirks rcar_i2c_quirks = {
+	.flags = I2C_AQ_NO_ZERO_LEN,
+};
+
 static const struct of_device_id rcar_i2c_dt_ids[] = {
 	{ .compatible = "renesas,i2c-r8a7778", .data = (void *)I2C_RCAR_GEN1 },
 	{ .compatible = "renesas,i2c-r8a7779", .data = (void *)I2C_RCAR_GEN1 },
@@ -942,6 +948,7 @@ static int rcar_i2c_probe(struct platform_device *pdev)
 	adap->dev.parent = dev;
 	adap->dev.of_node = dev->of_node;
 	adap->bus_recovery_info = &rcar_i2c_bri;
+	adap->quirks = &rcar_i2c_quirks;
 	i2c_set_adapdata(adap, priv);
 	strlcpy(adap->name, pdev->name, sizeof(adap->name));
 
diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c
index 9fe2b6951895..2f2e28d60ef5 100644
--- a/drivers/i2c/busses/i2c-s3c2410.c
+++ b/drivers/i2c/busses/i2c-s3c2410.c
@@ -919,9 +919,9 @@ static int s3c24xx_i2c_cpufreq_transition(struct notifier_block *nb,
 
 	if ((val == CPUFREQ_POSTCHANGE && delta_f < 0) ||
 	    (val == CPUFREQ_PRECHANGE && delta_f > 0)) {
-		i2c_lock_adapter(&i2c->adap);
+		i2c_lock_bus(&i2c->adap, I2C_LOCK_ROOT_ADAPTER);
 		ret = s3c24xx_i2c_clockrate(i2c, &got);
-		i2c_unlock_adapter(&i2c->adap);
+		i2c_unlock_bus(&i2c->adap, I2C_LOCK_ROOT_ADAPTER);
 
 		if (ret < 0)
 			dev_err(i2c->dev, "cannot find frequency (%d)\n", ret);
diff --git a/drivers/i2c/busses/i2c-sh_mobile.c b/drivers/i2c/busses/i2c-sh_mobile.c
index 5fda4188a9e5..9c7f6f8ceb22 100644
--- a/drivers/i2c/busses/i2c-sh_mobile.c
+++ b/drivers/i2c/busses/i2c-sh_mobile.c
@@ -613,11 +613,6 @@ static void sh_mobile_i2c_xfer_dma(struct sh_mobile_i2c_data *pd)
 static int start_ch(struct sh_mobile_i2c_data *pd, struct i2c_msg *usr_msg,
 		    bool do_init)
 {
-	if (usr_msg->len == 0 && (usr_msg->flags & I2C_M_RD)) {
-		dev_err(pd->dev, "Unsupported zero length i2c read\n");
-		return -EOPNOTSUPP;
-	}
-
 	if (do_init) {
 		/* Initialize channel registers */
 		iic_wr(pd, ICCR, ICCR_SCP);
@@ -758,6 +753,10 @@ static const struct i2c_algorithm sh_mobile_i2c_algorithm = {
 	.master_xfer	= sh_mobile_i2c_xfer,
 };
 
+static const struct i2c_adapter_quirks sh_mobile_i2c_quirks = {
+	.flags = I2C_AQ_NO_ZERO_LEN_READ,
+};
+
 /*
  * r8a7740 chip has lasting errata on I2C I/O pad reset.
  * this is work-around for it.
@@ -925,6 +924,7 @@ static int sh_mobile_i2c_probe(struct platform_device *dev)
 
 	adap->owner = THIS_MODULE;
 	adap->algo = &sh_mobile_i2c_algorithm;
+	adap->quirks = &sh_mobile_i2c_quirks;
 	adap->dev.parent = &dev->dev;
 	adap->retries = 5;
 	adap->nr = dev->id;
diff --git a/drivers/i2c/busses/i2c-sprd.c b/drivers/i2c/busses/i2c-sprd.c
index 4053259bccb8..a94e724f51dc 100644
--- a/drivers/i2c/busses/i2c-sprd.c
+++ b/drivers/i2c/busses/i2c-sprd.c
@@ -590,9 +590,9 @@ static int __maybe_unused sprd_i2c_suspend_noirq(struct device *pdev)
 {
 	struct sprd_i2c *i2c_dev = dev_get_drvdata(pdev);
 
-	i2c_lock_adapter(&i2c_dev->adap);
+	i2c_lock_bus(&i2c_dev->adap, I2C_LOCK_ROOT_ADAPTER);
 	i2c_dev->is_suspended = true;
-	i2c_unlock_adapter(&i2c_dev->adap);
+	i2c_unlock_bus(&i2c_dev->adap, I2C_LOCK_ROOT_ADAPTER);
 
 	return pm_runtime_force_suspend(pdev);
 }
@@ -601,9 +601,9 @@ static int __maybe_unused sprd_i2c_resume_noirq(struct device *pdev)
 {
 	struct sprd_i2c *i2c_dev = dev_get_drvdata(pdev);
 
-	i2c_lock_adapter(&i2c_dev->adap);
+	i2c_lock_bus(&i2c_dev->adap, I2C_LOCK_ROOT_ADAPTER);
 	i2c_dev->is_suspended = false;
-	i2c_unlock_adapter(&i2c_dev->adap);
+	i2c_unlock_bus(&i2c_dev->adap, I2C_LOCK_ROOT_ADAPTER);
 
 	return pm_runtime_force_resume(pdev);
 }
diff --git a/drivers/i2c/busses/i2c-stu300.c b/drivers/i2c/busses/i2c-stu300.c
index fce52bdab2b7..5503fa171df0 100644
--- a/drivers/i2c/busses/i2c-stu300.c
+++ b/drivers/i2c/busses/i2c-stu300.c
@@ -673,12 +673,6 @@ static int stu300_xfer_msg(struct i2c_adapter *adap,
 			msg->addr, msg->len, msg->flags, stop);
 	}
 
-	/* Zero-length messages are not supported by this hardware */
-	if (msg->len == 0) {
-		ret = -EINVAL;
-		goto exit_disable;
-	}
-
 	/*
 	 * For some reason, sending the address sometimes fails when running
 	 * on  the 13 MHz clock. No interrupt arrives. This is a work around,
@@ -863,6 +857,10 @@ static const struct i2c_algorithm stu300_algo = {
 	.functionality	= stu300_func,
 };
 
+static const struct i2c_adapter_quirks stu300_quirks = {
+	.flags = I2C_AQ_NO_ZERO_LEN,
+};
+
 static int stu300_probe(struct platform_device *pdev)
 {
 	struct stu300_dev *dev;
@@ -920,6 +918,8 @@ static int stu300_probe(struct platform_device *pdev)
 	adap->algo = &stu300_algo;
 	adap->dev.parent = &pdev->dev;
 	adap->dev.of_node = pdev->dev.of_node;
+	adap->quirks = &stu300_quirks;
+
 	i2c_set_adapdata(adap, dev);
 
 	/* i2c device drivers may be active on return from add_adapter() */
diff --git a/drivers/i2c/busses/i2c-tegra.c b/drivers/i2c/busses/i2c-tegra.c
index 797def5319f1..60c8561fbe65 100644
--- a/drivers/i2c/busses/i2c-tegra.c
+++ b/drivers/i2c/busses/i2c-tegra.c
@@ -115,6 +115,18 @@
 
 #define I2C_CONFIG_LOAD_TIMEOUT			1000000
 
+#define I2C_MST_FIFO_CONTROL			0x0b4
+#define I2C_MST_FIFO_CONTROL_RX_FLUSH		BIT(0)
+#define I2C_MST_FIFO_CONTROL_TX_FLUSH		BIT(1)
+#define I2C_MST_FIFO_CONTROL_RX_TRIG(x)		(((x) - 1) <<  4)
+#define I2C_MST_FIFO_CONTROL_TX_TRIG(x)		(((x) - 1) << 16)
+
+#define I2C_MST_FIFO_STATUS			0x0b8
+#define I2C_MST_FIFO_STATUS_RX_MASK		0xff
+#define I2C_MST_FIFO_STATUS_RX_SHIFT		0
+#define I2C_MST_FIFO_STATUS_TX_MASK		0xff0000
+#define I2C_MST_FIFO_STATUS_TX_SHIFT		16
+
 /*
  * msg_end_type: The bus control which need to be send at end of transfer.
  * @MSG_END_STOP: Send stop pulse at end of transfer.
@@ -154,6 +166,7 @@ struct tegra_i2c_hw_feature {
 	u16 clk_divisor_fast_plus_mode;
 	bool has_multi_master_mode;
 	bool has_slcg_override_reg;
+	bool has_mst_fifo;
 };
 
 /**
@@ -266,13 +279,24 @@ static void tegra_i2c_unmask_irq(struct tegra_i2c_dev *i2c_dev, u32 mask)
 static int tegra_i2c_flush_fifos(struct tegra_i2c_dev *i2c_dev)
 {
 	unsigned long timeout = jiffies + HZ;
-	u32 val = i2c_readl(i2c_dev, I2C_FIFO_CONTROL);
+	unsigned int offset;
+	u32 mask, val;
+
+	if (i2c_dev->hw->has_mst_fifo) {
+		mask = I2C_MST_FIFO_CONTROL_TX_FLUSH |
+		       I2C_MST_FIFO_CONTROL_RX_FLUSH;
+		offset = I2C_MST_FIFO_CONTROL;
+	} else {
+		mask = I2C_FIFO_CONTROL_TX_FLUSH |
+		       I2C_FIFO_CONTROL_RX_FLUSH;
+		offset = I2C_FIFO_CONTROL;
+	}
 
-	val |= I2C_FIFO_CONTROL_TX_FLUSH | I2C_FIFO_CONTROL_RX_FLUSH;
-	i2c_writel(i2c_dev, val, I2C_FIFO_CONTROL);
+	val = i2c_readl(i2c_dev, offset);
+	val |= mask;
+	i2c_writel(i2c_dev, val, offset);
 
-	while (i2c_readl(i2c_dev, I2C_FIFO_CONTROL) &
-		(I2C_FIFO_CONTROL_TX_FLUSH | I2C_FIFO_CONTROL_RX_FLUSH)) {
+	while (i2c_readl(i2c_dev, offset) & mask) {
 		if (time_after(jiffies, timeout)) {
 			dev_warn(i2c_dev->dev, "timeout waiting for fifo flush\n");
 			return -ETIMEDOUT;
@@ -290,9 +314,15 @@ static int tegra_i2c_empty_rx_fifo(struct tegra_i2c_dev *i2c_dev)
 	size_t buf_remaining = i2c_dev->msg_buf_remaining;
 	int words_to_transfer;
 
-	val = i2c_readl(i2c_dev, I2C_FIFO_STATUS);
-	rx_fifo_avail = (val & I2C_FIFO_STATUS_RX_MASK) >>
-		I2C_FIFO_STATUS_RX_SHIFT;
+	if (i2c_dev->hw->has_mst_fifo) {
+		val = i2c_readl(i2c_dev, I2C_MST_FIFO_STATUS);
+		rx_fifo_avail = (val & I2C_MST_FIFO_STATUS_RX_MASK) >>
+			I2C_MST_FIFO_STATUS_RX_SHIFT;
+	} else {
+		val = i2c_readl(i2c_dev, I2C_FIFO_STATUS);
+		rx_fifo_avail = (val & I2C_FIFO_STATUS_RX_MASK) >>
+			I2C_FIFO_STATUS_RX_SHIFT;
+	}
 
 	/* Rounds down to not include partial word at the end of buf */
 	words_to_transfer = buf_remaining / BYTES_PER_FIFO_WORD;
@@ -321,6 +351,7 @@ static int tegra_i2c_empty_rx_fifo(struct tegra_i2c_dev *i2c_dev)
 	BUG_ON(rx_fifo_avail > 0 && buf_remaining > 0);
 	i2c_dev->msg_buf_remaining = buf_remaining;
 	i2c_dev->msg_buf = buf;
+
 	return 0;
 }
 
@@ -332,9 +363,15 @@ static int tegra_i2c_fill_tx_fifo(struct tegra_i2c_dev *i2c_dev)
 	size_t buf_remaining = i2c_dev->msg_buf_remaining;
 	int words_to_transfer;
 
-	val = i2c_readl(i2c_dev, I2C_FIFO_STATUS);
-	tx_fifo_avail = (val & I2C_FIFO_STATUS_TX_MASK) >>
-		I2C_FIFO_STATUS_TX_SHIFT;
+	if (i2c_dev->hw->has_mst_fifo) {
+		val = i2c_readl(i2c_dev, I2C_MST_FIFO_STATUS);
+		tx_fifo_avail = (val & I2C_MST_FIFO_STATUS_TX_MASK) >>
+			I2C_MST_FIFO_STATUS_TX_SHIFT;
+	} else {
+		val = i2c_readl(i2c_dev, I2C_FIFO_STATUS);
+		tx_fifo_avail = (val & I2C_FIFO_STATUS_TX_MASK) >>
+			I2C_FIFO_STATUS_TX_SHIFT;
+	}
 
 	/* Rounds down to not include partial word at the end of buf */
 	words_to_transfer = buf_remaining / BYTES_PER_FIFO_WORD;
@@ -516,9 +553,15 @@ static int tegra_i2c_init(struct tegra_i2c_dev *i2c_dev)
 		i2c_writel(i2c_dev, 0x00, I2C_SL_ADDR2);
 	}
 
-	val = 7 << I2C_FIFO_CONTROL_TX_TRIG_SHIFT |
-		0 << I2C_FIFO_CONTROL_RX_TRIG_SHIFT;
-	i2c_writel(i2c_dev, val, I2C_FIFO_CONTROL);
+	if (i2c_dev->hw->has_mst_fifo) {
+		val = I2C_MST_FIFO_CONTROL_TX_TRIG(8) |
+		      I2C_MST_FIFO_CONTROL_RX_TRIG(1);
+		i2c_writel(i2c_dev, val, I2C_MST_FIFO_CONTROL);
+	} else {
+		val = 7 << I2C_FIFO_CONTROL_TX_TRIG_SHIFT |
+			0 << I2C_FIFO_CONTROL_RX_TRIG_SHIFT;
+		i2c_writel(i2c_dev, val, I2C_FIFO_CONTROL);
+	}
 
 	err = tegra_i2c_flush_fifos(i2c_dev);
 	if (err)
@@ -802,6 +845,7 @@ static const struct tegra_i2c_hw_feature tegra20_i2c_hw = {
 	.has_config_load_reg = false,
 	.has_multi_master_mode = false,
 	.has_slcg_override_reg = false,
+	.has_mst_fifo = false,
 };
 
 static const struct tegra_i2c_hw_feature tegra30_i2c_hw = {
@@ -814,6 +858,7 @@ static const struct tegra_i2c_hw_feature tegra30_i2c_hw = {
 	.has_config_load_reg = false,
 	.has_multi_master_mode = false,
 	.has_slcg_override_reg = false,
+	.has_mst_fifo = false,
 };
 
 static const struct tegra_i2c_hw_feature tegra114_i2c_hw = {
@@ -826,6 +871,7 @@ static const struct tegra_i2c_hw_feature tegra114_i2c_hw = {
 	.has_config_load_reg = false,
 	.has_multi_master_mode = false,
 	.has_slcg_override_reg = false,
+	.has_mst_fifo = false,
 };
 
 static const struct tegra_i2c_hw_feature tegra124_i2c_hw = {
@@ -838,6 +884,7 @@ static const struct tegra_i2c_hw_feature tegra124_i2c_hw = {
 	.has_config_load_reg = true,
 	.has_multi_master_mode = false,
 	.has_slcg_override_reg = true,
+	.has_mst_fifo = false,
 };
 
 static const struct tegra_i2c_hw_feature tegra210_i2c_hw = {
@@ -850,10 +897,25 @@ static const struct tegra_i2c_hw_feature tegra210_i2c_hw = {
 	.has_config_load_reg = true,
 	.has_multi_master_mode = true,
 	.has_slcg_override_reg = true,
+	.has_mst_fifo = false,
+};
+
+static const struct tegra_i2c_hw_feature tegra194_i2c_hw = {
+	.has_continue_xfer_support = true,
+	.has_per_pkt_xfer_complete_irq = true,
+	.has_single_clk_source = true,
+	.clk_divisor_hs_mode = 1,
+	.clk_divisor_std_fast_mode = 0x19,
+	.clk_divisor_fast_plus_mode = 0x10,
+	.has_config_load_reg = true,
+	.has_multi_master_mode = true,
+	.has_slcg_override_reg = true,
+	.has_mst_fifo = true,
 };
 
 /* Match table for of_platform binding */
 static const struct of_device_id tegra_i2c_of_match[] = {
+	{ .compatible = "nvidia,tegra194-i2c", .data = &tegra194_i2c_hw, },
 	{ .compatible = "nvidia,tegra210-i2c", .data = &tegra210_i2c_hw, },
 	{ .compatible = "nvidia,tegra124-i2c", .data = &tegra124_i2c_hw, },
 	{ .compatible = "nvidia,tegra114-i2c", .data = &tegra114_i2c_hw, },
diff --git a/drivers/i2c/busses/i2c-xlr.c b/drivers/i2c/busses/i2c-xlr.c
index 484bfa15d58e..34cd4b308540 100644
--- a/drivers/i2c/busses/i2c-xlr.c
+++ b/drivers/i2c/busses/i2c-xlr.c
@@ -173,9 +173,6 @@ static int xlr_i2c_tx(struct xlr_i2c_private *priv,  u16 len,
 	u8 offset;
 	u32 xfer;
 
-	if (!len)
-		return -EOPNOTSUPP;
-
 	offset = buf[0];
 	xlr_i2c_wreg(priv->iobase, XLR_I2C_ADDR, offset);
 	xlr_i2c_wreg(priv->iobase, XLR_I2C_DEVADDR, addr);
@@ -241,9 +238,6 @@ static int xlr_i2c_rx(struct xlr_i2c_private *priv, u16 len, u8 *buf, u16 addr)
 	unsigned long timeout, stoptime, checktime;
 	int nbytes, timedout;
 
-	if (!len)
-		return -EOPNOTSUPP;
-
 	xlr_i2c_wreg(priv->iobase, XLR_I2C_CFG,
 			XLR_I2C_CFG_NOADDR | priv->cfg->cfg_extra);
 	xlr_i2c_wreg(priv->iobase, XLR_I2C_BYTECNT, len - 1);
@@ -340,6 +334,10 @@ static const struct i2c_algorithm xlr_i2c_algo = {
 	.functionality	= xlr_func,
 };
 
+static const struct i2c_adapter_quirks xlr_i2c_quirks = {
+	.flags = I2C_AQ_NO_ZERO_LEN,
+};
+
 static const struct xlr_i2c_config xlr_i2c_config_default = {
 	.status_busy	= XLR_I2C_BUS_BUSY,
 	.cfg_extra	= 0,
@@ -427,6 +425,7 @@ static int xlr_i2c_probe(struct platform_device *pdev)
 	priv->adap.owner	= THIS_MODULE;
 	priv->adap.algo_data	= priv;
 	priv->adap.algo		= &xlr_i2c_algo;
+	priv->adap.quirks	= &xlr_i2c_quirks;
 	priv->adap.nr		= pdev->id;
 	priv->adap.class	= I2C_CLASS_HWMON;
 	snprintf(priv->adap.name, sizeof(priv->adap.name), "xlr-i2c");
diff --git a/drivers/i2c/i2c-core-acpi.c b/drivers/i2c/i2c-core-acpi.c
index 7c3b4740b94b..32affd3fa8bd 100644
--- a/drivers/i2c/i2c-core-acpi.c
+++ b/drivers/i2c/i2c-core-acpi.c
@@ -453,8 +453,12 @@ static int acpi_gsb_i2c_read_bytes(struct i2c_client *client,
 		else
 			dev_err(&client->adapter->dev, "i2c read %d bytes from client@%#x starting at reg %#x failed, error: %d\n",
 				data_len, client->addr, cmd, ret);
-	} else {
+	/* 2 transfers must have completed successfully */
+	} else if (ret == 2) {
 		memcpy(data, buffer, data_len);
+		ret = 0;
+	} else {
+		ret = -EIO;
 	}
 
 	kfree(buffer);
@@ -482,11 +486,16 @@ static int acpi_gsb_i2c_write_bytes(struct i2c_client *client,
 	msgs[0].buf = buffer;
 
 	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
-	if (ret < 0)
-		dev_err(&client->adapter->dev, "i2c write failed\n");
 
 	kfree(buffer);
-	return ret;
+
+	if (ret < 0) {
+		dev_err(&client->adapter->dev, "i2c write failed: %d\n", ret);
+		return ret;
+	}
+
+	/* 1 transfer must have completed successfully */
+	return (ret == 1) ? 0 : -EIO;
 }
 
 static acpi_status
@@ -590,8 +599,6 @@ i2c_acpi_space_handler(u32 function, acpi_physical_address command,
 		if (action == ACPI_READ) {
 			status = acpi_gsb_i2c_read_bytes(client, command,
 					gsb->data, info->access_length);
-			if (status > 0)
-				status = 0;
 		} else {
 			status = acpi_gsb_i2c_write_bytes(client, command,
 					gsb->data, info->access_length);
diff --git a/drivers/i2c/i2c-core-base.c b/drivers/i2c/i2c-core-base.c
index 15c95aaa484c..5a937109a289 100644
--- a/drivers/i2c/i2c-core-base.c
+++ b/drivers/i2c/i2c-core-base.c
@@ -158,6 +158,22 @@ static void set_sda_gpio_value(struct i2c_adapter *adap, int val)
 	gpiod_set_value_cansleep(adap->bus_recovery_info->sda_gpiod, val);
 }
 
+static int i2c_generic_bus_free(struct i2c_adapter *adap)
+{
+	struct i2c_bus_recovery_info *bri = adap->bus_recovery_info;
+	int ret = -EOPNOTSUPP;
+
+	if (bri->get_bus_free)
+		ret = bri->get_bus_free(adap);
+	else if (bri->get_sda)
+		ret = bri->get_sda(adap);
+
+	if (ret < 0)
+		return ret;
+
+	return ret ? 0 : -EBUSY;
+}
+
 /*
  * We are generating clock pulses. ndelay() determines durating of clk pulses.
  * We will generate clock with rate 100 KHz and so duration of both clock levels
@@ -169,21 +185,28 @@ static void set_sda_gpio_value(struct i2c_adapter *adap, int val)
 int i2c_generic_scl_recovery(struct i2c_adapter *adap)
 {
 	struct i2c_bus_recovery_info *bri = adap->bus_recovery_info;
-	int i = 0, val = 1, ret = 0;
+	int i = 0, scl = 1, ret;
 
 	if (bri->prepare_recovery)
 		bri->prepare_recovery(adap);
 
-	bri->set_scl(adap, val);
+	/*
+	 * If we can set SDA, we will always create a STOP to ensure additional
+	 * pulses will do no harm. This is achieved by letting SDA follow SCL
+	 * half a cycle later. Check the 'incomplete_write_byte' fault injector
+	 * for details.
+	 */
+	bri->set_scl(adap, scl);
+	ndelay(RECOVERY_NDELAY / 2);
 	if (bri->set_sda)
-		bri->set_sda(adap, 1);
-	ndelay(RECOVERY_NDELAY);
+		bri->set_sda(adap, scl);
+	ndelay(RECOVERY_NDELAY / 2);
 
 	/*
 	 * By this time SCL is high, as we need to give 9 falling-rising edges
 	 */
 	while (i++ < RECOVERY_CLK_CNT * 2) {
-		if (val) {
+		if (scl) {
 			/* SCL shouldn't be low here */
 			if (!bri->get_scl(adap)) {
 				dev_err(&adap->dev,
@@ -191,41 +214,27 @@ int i2c_generic_scl_recovery(struct i2c_adapter *adap)
 				ret = -EBUSY;
 				break;
 			}
-			/* Break if SDA is high */
-			if (bri->get_sda && bri->get_sda(adap))
-				break;
 		}
 
-		val = !val;
-		bri->set_scl(adap, val);
-
-		/*
-		 * If we can set SDA, we will always create STOP here to ensure
-		 * the additional pulses will do no harm. This is achieved by
-		 * letting SDA follow SCL half a cycle later.
-		 */
+		scl = !scl;
+		bri->set_scl(adap, scl);
+		/* Creating STOP again, see above */
 		ndelay(RECOVERY_NDELAY / 2);
 		if (bri->set_sda)
-			bri->set_sda(adap, val);
+			bri->set_sda(adap, scl);
 		ndelay(RECOVERY_NDELAY / 2);
-	}
 
-	/* check if recovery actually succeeded */
-	if (bri->get_sda && !bri->get_sda(adap))
-		ret = -EBUSY;
-
-	/* If all went well, send STOP for a sane bus state. */
-	if (ret == 0 && bri->set_sda) {
-		bri->set_scl(adap, 0);
-		ndelay(RECOVERY_NDELAY / 2);
-		bri->set_sda(adap, 0);
-		ndelay(RECOVERY_NDELAY / 2);
-		bri->set_scl(adap, 1);
-		ndelay(RECOVERY_NDELAY / 2);
-		bri->set_sda(adap, 1);
-		ndelay(RECOVERY_NDELAY / 2);
+		if (scl) {
+			ret = i2c_generic_bus_free(adap);
+			if (ret == 0)
+				break;
+		}
 	}
 
+	/* If we can't check bus status, assume recovery worked */
+	if (ret == -EOPNOTSUPP)
+		ret = 0;
+
 	if (bri->unprepare_recovery)
 		bri->unprepare_recovery(adap);
 
@@ -274,6 +283,10 @@ static void i2c_init_recovery(struct i2c_adapter *adap)
 			err_str = "no {get|set}_scl() found";
 			goto err;
 		}
+		if (!bri->set_sda && !bri->get_sda) {
+			err_str = "either get_sda() or set_sda() needed";
+			goto err;
+		}
 	}
 
 	return;
@@ -1563,6 +1576,8 @@ void i2c_parse_fw_timings(struct device *dev, struct i2c_timings *t, bool use_de
 	ret = device_property_read_u32(dev, "i2c-sda-falling-time-ns", &t->sda_fall_ns);
 	if (ret && use_defaults)
 		t->sda_fall_ns = t->scl_fall_ns;
+
+	device_property_read_u32(dev, "i2c-sda-hold-time-ns", &t->sda_hold_ns);
 }
 EXPORT_SYMBOL_GPL(i2c_parse_fw_timings);
 
@@ -1826,9 +1841,15 @@ static int i2c_check_for_quirks(struct i2c_adapter *adap, struct i2c_msg *msgs,
 		if (msgs[i].flags & I2C_M_RD) {
 			if (do_len_check && i2c_quirk_exceeded(len, q->max_read_len))
 				return i2c_quirk_error(adap, &msgs[i], "msg too long");
+
+			if (q->flags & I2C_AQ_NO_ZERO_LEN_READ && len == 0)
+				return i2c_quirk_error(adap, &msgs[i], "no zero length");
 		} else {
 			if (do_len_check && i2c_quirk_exceeded(len, q->max_write_len))
 				return i2c_quirk_error(adap, &msgs[i], "msg too long");
+
+			if (q->flags & I2C_AQ_NO_ZERO_LEN_WRITE && len == 0)
+				return i2c_quirk_error(adap, &msgs[i], "no zero length");
 		}
 	}
 
diff --git a/drivers/i2c/i2c-core-slave.c b/drivers/i2c/i2c-core-slave.c
index 4a78c65e9971..47a9f70a24a9 100644
--- a/drivers/i2c/i2c-core-slave.c
+++ b/drivers/i2c/i2c-core-slave.c
@@ -47,9 +47,9 @@ int i2c_slave_register(struct i2c_client *client, i2c_slave_cb_t slave_cb)
 
 	client->slave_cb = slave_cb;
 
-	i2c_lock_adapter(client->adapter);
+	i2c_lock_bus(client->adapter, I2C_LOCK_ROOT_ADAPTER);
 	ret = client->adapter->algo->reg_slave(client);
-	i2c_unlock_adapter(client->adapter);
+	i2c_unlock_bus(client->adapter, I2C_LOCK_ROOT_ADAPTER);
 
 	if (ret) {
 		client->slave_cb = NULL;
@@ -69,9 +69,9 @@ int i2c_slave_unregister(struct i2c_client *client)
 		return -EOPNOTSUPP;
 	}
 
-	i2c_lock_adapter(client->adapter);
+	i2c_lock_bus(client->adapter, I2C_LOCK_ROOT_ADAPTER);
 	ret = client->adapter->algo->unreg_slave(client);
-	i2c_unlock_adapter(client->adapter);
+	i2c_unlock_bus(client->adapter, I2C_LOCK_ROOT_ADAPTER);
 
 	if (ret == 0)
 		client->slave_cb = NULL;
diff --git a/drivers/i2c/i2c-mux.c b/drivers/i2c/i2c-mux.c
index 29646aa6132e..f330690b4125 100644
--- a/drivers/i2c/i2c-mux.c
+++ b/drivers/i2c/i2c-mux.c
@@ -87,8 +87,8 @@ static int __i2c_mux_smbus_xfer(struct i2c_adapter *adap,
 
 	ret = muxc->select(muxc, priv->chan_id);
 	if (ret >= 0)
-		ret = parent->algo->smbus_xfer(parent, addr, flags,
-					read_write, command, size, data);
+		ret = __i2c_smbus_xfer(parent, addr, flags,
+				       read_write, command, size, data);
 	if (muxc->deselect)
 		muxc->deselect(muxc, priv->chan_id);
 
diff --git a/drivers/i2c/muxes/i2c-mux-mlxcpld.c b/drivers/i2c/muxes/i2c-mux-mlxcpld.c
index 12ad8d65faf6..f2bf3e57ed67 100644
--- a/drivers/i2c/muxes/i2c-mux-mlxcpld.c
+++ b/drivers/i2c/muxes/i2c-mux-mlxcpld.c
@@ -94,31 +94,11 @@ static int mlxcpld_mux_reg_write(struct i2c_adapter *adap,
 				 struct i2c_client *client, u8 val)
 {
 	struct mlxcpld_mux_plat_data *pdata = dev_get_platdata(&client->dev);
-	int ret = -ENODEV;
-
-	if (adap->algo->master_xfer) {
-		struct i2c_msg msg;
-		u8 msgbuf[] = {pdata->sel_reg_addr, val};
-
-		msg.addr = client->addr;
-		msg.flags = 0;
-		msg.len = 2;
-		msg.buf = msgbuf;
-		ret = __i2c_transfer(adap, &msg, 1);
-
-		if (ret >= 0 && ret != 1)
-			ret = -EREMOTEIO;
-	} else if (adap->algo->smbus_xfer) {
-		union i2c_smbus_data data;
-
-		data.byte = val;
-		ret = adap->algo->smbus_xfer(adap, client->addr,
-					     client->flags, I2C_SMBUS_WRITE,
-					     pdata->sel_reg_addr,
-					     I2C_SMBUS_BYTE_DATA, &data);
-	}
+	union i2c_smbus_data data = { .byte = val };
 
-	return ret;
+	return __i2c_smbus_xfer(adap, client->addr, client->flags,
+				I2C_SMBUS_WRITE, pdata->sel_reg_addr,
+				I2C_SMBUS_BYTE_DATA, &data);
 }
 
 static int mlxcpld_mux_select_chan(struct i2c_mux_core *muxc, u32 chan)
diff --git a/drivers/i2c/muxes/i2c-mux-pca9541.c b/drivers/i2c/muxes/i2c-mux-pca9541.c
index 6a39adaf433f..9e75d6b9140b 100644
--- a/drivers/i2c/muxes/i2c-mux-pca9541.c
+++ b/drivers/i2c/muxes/i2c-mux-pca9541.c
@@ -99,31 +99,11 @@ MODULE_DEVICE_TABLE(of, pca9541_of_match);
 static int pca9541_reg_write(struct i2c_client *client, u8 command, u8 val)
 {
 	struct i2c_adapter *adap = client->adapter;
-	int ret;
-
-	if (adap->algo->master_xfer) {
-		struct i2c_msg msg;
-		char buf[2];
-
-		msg.addr = client->addr;
-		msg.flags = 0;
-		msg.len = 2;
-		buf[0] = command;
-		buf[1] = val;
-		msg.buf = buf;
-		ret = __i2c_transfer(adap, &msg, 1);
-	} else {
-		union i2c_smbus_data data;
-
-		data.byte = val;
-		ret = adap->algo->smbus_xfer(adap, client->addr,
-					     client->flags,
-					     I2C_SMBUS_WRITE,
-					     command,
-					     I2C_SMBUS_BYTE_DATA, &data);
-	}
+	union i2c_smbus_data data = { .byte = val };
 
-	return ret;
+	return __i2c_smbus_xfer(adap, client->addr, client->flags,
+				I2C_SMBUS_WRITE, command,
+				I2C_SMBUS_BYTE_DATA, &data);
 }
 
 /*
@@ -133,41 +113,14 @@ static int pca9541_reg_write(struct i2c_client *client, u8 command, u8 val)
 static int pca9541_reg_read(struct i2c_client *client, u8 command)
 {
 	struct i2c_adapter *adap = client->adapter;
+	union i2c_smbus_data data;
 	int ret;
-	u8 val;
-
-	if (adap->algo->master_xfer) {
-		struct i2c_msg msg[2] = {
-			{
-				.addr = client->addr,
-				.flags = 0,
-				.len = 1,
-				.buf = &command
-			},
-			{
-				.addr = client->addr,
-				.flags = I2C_M_RD,
-				.len = 1,
-				.buf = &val
-			}
-		};
-		ret = __i2c_transfer(adap, msg, 2);
-		if (ret == 2)
-			ret = val;
-		else if (ret >= 0)
-			ret = -EIO;
-	} else {
-		union i2c_smbus_data data;
-
-		ret = adap->algo->smbus_xfer(adap, client->addr,
-					     client->flags,
-					     I2C_SMBUS_READ,
-					     command,
-					     I2C_SMBUS_BYTE_DATA, &data);
-		if (!ret)
-			ret = data.byte;
-	}
-	return ret;
+
+	ret = __i2c_smbus_xfer(adap, client->addr, client->flags,
+			       I2C_SMBUS_READ, command,
+			       I2C_SMBUS_BYTE_DATA, &data);
+
+	return ret ?: data.byte;
 }
 
 /*
@@ -345,11 +298,11 @@ static int pca9541_probe(struct i2c_client *client,
 
 	/*
 	 * I2C accesses are unprotected here.
-	 * We have to lock the adapter before releasing the bus.
+	 * We have to lock the I2C segment before releasing the bus.
 	 */
-	i2c_lock_adapter(adap);
+	i2c_lock_bus(adap, I2C_LOCK_SEGMENT);
 	pca9541_release_bus(client);
-	i2c_unlock_adapter(adap);
+	i2c_unlock_bus(adap, I2C_LOCK_SEGMENT);
 
 	/* Create mux adapter */
 
diff --git a/drivers/i2c/muxes/i2c-mux-pca954x.c b/drivers/i2c/muxes/i2c-mux-pca954x.c
index fbc748027087..24bd9275fde5 100644
--- a/drivers/i2c/muxes/i2c-mux-pca954x.c
+++ b/drivers/i2c/muxes/i2c-mux-pca954x.c
@@ -220,30 +220,11 @@ MODULE_DEVICE_TABLE(of, pca954x_of_match);
 static int pca954x_reg_write(struct i2c_adapter *adap,
 			     struct i2c_client *client, u8 val)
 {
-	int ret = -ENODEV;
-
-	if (adap->algo->master_xfer) {
-		struct i2c_msg msg;
-		char buf[1];
-
-		msg.addr = client->addr;
-		msg.flags = 0;
-		msg.len = 1;
-		buf[0] = val;
-		msg.buf = buf;
-		ret = __i2c_transfer(adap, &msg, 1);
-
-		if (ret >= 0 && ret != 1)
-			ret = -EREMOTEIO;
-	} else {
-		union i2c_smbus_data data;
-		ret = adap->algo->smbus_xfer(adap, client->addr,
-					     client->flags,
-					     I2C_SMBUS_WRITE,
-					     val, I2C_SMBUS_BYTE, &data);
-	}
+	union i2c_smbus_data dummy;
 
-	return ret;
+	return __i2c_smbus_xfer(adap, client->addr, client->flags,
+				I2C_SMBUS_WRITE, val,
+				I2C_SMBUS_BYTE, &dummy);
 }
 
 static int pca954x_select_chan(struct i2c_mux_core *muxc, u32 chan)
@@ -368,7 +349,8 @@ static int pca954x_probe(struct i2c_client *client,
 {
 	struct i2c_adapter *adap = to_i2c_adapter(client->dev.parent);
 	struct pca954x_platform_data *pdata = dev_get_platdata(&client->dev);
-	struct device_node *of_node = client->dev.of_node;
+	struct device *dev = &client->dev;
+	struct device_node *np = dev->of_node;
 	bool idle_disconnect_dt;
 	struct gpio_desc *gpio;
 	int num, force, class;
@@ -379,8 +361,7 @@ static int pca954x_probe(struct i2c_client *client,
 	if (!i2c_check_functionality(adap, I2C_FUNC_SMBUS_BYTE))
 		return -ENODEV;
 
-	muxc = i2c_mux_alloc(adap, &client->dev,
-			     PCA954X_MAX_NCHANS, sizeof(*data), 0,
+	muxc = i2c_mux_alloc(adap, dev, PCA954X_MAX_NCHANS, sizeof(*data), 0,
 			     pca954x_select_chan, pca954x_deselect_mux);
 	if (!muxc)
 		return -ENOMEM;
@@ -390,7 +371,7 @@ static int pca954x_probe(struct i2c_client *client,
 	data->client = client;
 
 	/* Reset the mux if a reset GPIO is specified. */
-	gpio = devm_gpiod_get_optional(&client->dev, "reset", GPIOD_OUT_HIGH);
+	gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
 	if (IS_ERR(gpio))
 		return PTR_ERR(gpio);
 	if (gpio) {
@@ -400,7 +381,7 @@ static int pca954x_probe(struct i2c_client *client,
 		udelay(1);
 	}
 
-	data->chip = of_device_get_match_data(&client->dev);
+	data->chip = of_device_get_match_data(dev);
 	if (!data->chip)
 		data->chip = &chips[id->driver_data];
 
@@ -414,8 +395,7 @@ static int pca954x_probe(struct i2c_client *client,
 		if (!ret &&
 		    (id.manufacturer_id != data->chip->id.manufacturer_id ||
 		     id.part_id != data->chip->id.part_id)) {
-			dev_warn(&client->dev,
-				 "unexpected device id %03x-%03x-%x\n",
+			dev_warn(dev, "unexpected device id %03x-%03x-%x\n",
 				 id.manufacturer_id, id.part_id,
 				 id.die_revision);
 			return -ENODEV;
@@ -427,14 +407,14 @@ static int pca954x_probe(struct i2c_client *client,
 	 * initializes the mux to disconnected state.
 	 */
 	if (i2c_smbus_write_byte(client, 0) < 0) {
-		dev_warn(&client->dev, "probe failed\n");
+		dev_warn(dev, "probe failed\n");
 		return -ENODEV;
 	}
 
 	data->last_chan = 0;		   /* force the first selection */
 
-	idle_disconnect_dt = of_node &&
-		of_property_read_bool(of_node, "i2c-mux-idle-disconnect");
+	idle_disconnect_dt = np &&
+		of_property_read_bool(np, "i2c-mux-idle-disconnect");
 
 	ret = pca954x_irq_setup(muxc);
 	if (ret)
@@ -465,7 +445,7 @@ static int pca954x_probe(struct i2c_client *client,
 	}
 
 	if (data->irq) {
-		ret = devm_request_threaded_irq(&client->dev, data->client->irq,
+		ret = devm_request_threaded_irq(dev, data->client->irq,
 						NULL, pca954x_irq_handler,
 						IRQF_ONESHOT | IRQF_SHARED,
 						"pca954x", data);
@@ -473,8 +453,7 @@ static int pca954x_probe(struct i2c_client *client,
 			goto fail_cleanup;
 	}
 
-	dev_info(&client->dev,
-		 "registered %d multiplexed busses for I2C %s %s\n",
+	dev_info(dev, "registered %d multiplexed busses for I2C %s %s\n",
 		 num, data->chip->muxtype == pca954x_ismux
 				? "mux" : "switch", client->name);
 
diff --git a/drivers/iio/temperature/mlx90614.c b/drivers/iio/temperature/mlx90614.c
index d619e8634a00..13a4cec64ea8 100644
--- a/drivers/iio/temperature/mlx90614.c
+++ b/drivers/iio/temperature/mlx90614.c
@@ -433,11 +433,11 @@ static int mlx90614_wakeup(struct mlx90614_data *data)
 
 	dev_dbg(&data->client->dev, "Requesting wake-up");
 
-	i2c_lock_adapter(data->client->adapter);
+	i2c_lock_bus(data->client->adapter, I2C_LOCK_ROOT_ADAPTER);
 	gpiod_direction_output(data->wakeup_gpio, 0);
 	msleep(MLX90614_TIMING_WAKEUP);
 	gpiod_direction_input(data->wakeup_gpio);
-	i2c_unlock_adapter(data->client->adapter);
+	i2c_unlock_bus(data->client->adapter, I2C_LOCK_ROOT_ADAPTER);
 
 	data->ready_timestamp = jiffies +
 			msecs_to_jiffies(MLX90614_TIMING_STARTUP);
diff --git a/drivers/input/touchscreen/rohm_bu21023.c b/drivers/input/touchscreen/rohm_bu21023.c
index bda0500c9b57..714affdd742f 100644
--- a/drivers/input/touchscreen/rohm_bu21023.c
+++ b/drivers/input/touchscreen/rohm_bu21023.c
@@ -304,7 +304,7 @@ static int rohm_i2c_burst_read(struct i2c_client *client, u8 start, void *buf,
 	msg[1].len = len;
 	msg[1].buf = buf;
 
-	i2c_lock_adapter(adap);
+	i2c_lock_bus(adap, I2C_LOCK_SEGMENT);
 
 	for (i = 0; i < 2; i++) {
 		if (__i2c_transfer(adap, &msg[i], 1) < 0) {
@@ -313,7 +313,7 @@ static int rohm_i2c_burst_read(struct i2c_client *client, u8 start, void *buf,
 		}
 	}
 
-	i2c_unlock_adapter(adap);
+	i2c_unlock_bus(adap, I2C_LOCK_SEGMENT);
 
 	return ret;
 }
diff --git a/drivers/media/dvb-frontends/af9013.c b/drivers/media/dvb-frontends/af9013.c
index f3acbb57d48c..35a93b251aab 100644
--- a/drivers/media/dvb-frontends/af9013.c
+++ b/drivers/media/dvb-frontends/af9013.c
@@ -1311,10 +1311,10 @@ static int af9013_wregs(struct i2c_client *client, u8 cmd, u16 reg,
 	memcpy(&buf[3], val, len);
 
 	if (lock)
-		i2c_lock_adapter(client->adapter);
+		i2c_lock_bus(client->adapter, I2C_LOCK_SEGMENT);
 	ret = __i2c_transfer(client->adapter, msg, 1);
 	if (lock)
-		i2c_unlock_adapter(client->adapter);
+		i2c_unlock_bus(client->adapter, I2C_LOCK_SEGMENT);
 	if (ret < 0) {
 		goto err;
 	} else if (ret != 1) {
@@ -1352,10 +1352,10 @@ static int af9013_rregs(struct i2c_client *client, u8 cmd, u16 reg,
 	buf[2] = cmd;
 
 	if (lock)
-		i2c_lock_adapter(client->adapter);
+		i2c_lock_bus(client->adapter, I2C_LOCK_SEGMENT);
 	ret = __i2c_transfer(client->adapter, msg, 2);
 	if (lock)
-		i2c_unlock_adapter(client->adapter);
+		i2c_unlock_bus(client->adapter, I2C_LOCK_SEGMENT);
 	if (ret < 0) {
 		goto err;
 	} else if (ret != 2) {
diff --git a/drivers/media/dvb-frontends/drxk_hard.c b/drivers/media/dvb-frontends/drxk_hard.c
index f1886945a7bc..84ac3f73f8fe 100644
--- a/drivers/media/dvb-frontends/drxk_hard.c
+++ b/drivers/media/dvb-frontends/drxk_hard.c
@@ -213,7 +213,7 @@ static inline u32 log10times100(u32 value)
 
 static int drxk_i2c_lock(struct drxk_state *state)
 {
-	i2c_lock_adapter(state->i2c);
+	i2c_lock_bus(state->i2c, I2C_LOCK_SEGMENT);
 	state->drxk_i2c_exclusive_lock = true;
 
 	return 0;
@@ -224,7 +224,7 @@ static void drxk_i2c_unlock(struct drxk_state *state)
 	if (!state->drxk_i2c_exclusive_lock)
 		return;
 
-	i2c_unlock_adapter(state->i2c);
+	i2c_unlock_bus(state->i2c, I2C_LOCK_SEGMENT);
 	state->drxk_i2c_exclusive_lock = false;
 }
 
diff --git a/drivers/media/dvb-frontends/rtl2830.c b/drivers/media/dvb-frontends/rtl2830.c
index adc9046d5a90..c0659568471b 100644
--- a/drivers/media/dvb-frontends/rtl2830.c
+++ b/drivers/media/dvb-frontends/rtl2830.c
@@ -24,9 +24,9 @@ static int rtl2830_bulk_write(struct i2c_client *client, unsigned int reg,
 	struct rtl2830_dev *dev = i2c_get_clientdata(client);
 	int ret;
 
-	i2c_lock_adapter(client->adapter);
+	i2c_lock_bus(client->adapter, I2C_LOCK_SEGMENT);
 	ret = regmap_bulk_write(dev->regmap, reg, val, val_count);
-	i2c_unlock_adapter(client->adapter);
+	i2c_unlock_bus(client->adapter, I2C_LOCK_SEGMENT);
 	return ret;
 }
 
@@ -36,9 +36,9 @@ static int rtl2830_update_bits(struct i2c_client *client, unsigned int reg,
 	struct rtl2830_dev *dev = i2c_get_clientdata(client);
 	int ret;
 
-	i2c_lock_adapter(client->adapter);
+	i2c_lock_bus(client->adapter, I2C_LOCK_SEGMENT);
 	ret = regmap_update_bits(dev->regmap, reg, mask, val);
-	i2c_unlock_adapter(client->adapter);
+	i2c_unlock_bus(client->adapter, I2C_LOCK_SEGMENT);
 	return ret;
 }
 
@@ -48,9 +48,9 @@ static int rtl2830_bulk_read(struct i2c_client *client, unsigned int reg,
 	struct rtl2830_dev *dev = i2c_get_clientdata(client);
 	int ret;
 
-	i2c_lock_adapter(client->adapter);
+	i2c_lock_bus(client->adapter, I2C_LOCK_SEGMENT);
 	ret = regmap_bulk_read(dev->regmap, reg, val, val_count);
-	i2c_unlock_adapter(client->adapter);
+	i2c_unlock_bus(client->adapter, I2C_LOCK_SEGMENT);
 	return ret;
 }
 
diff --git a/drivers/media/dvb-frontends/tda1004x.c b/drivers/media/dvb-frontends/tda1004x.c
index d402e4b722ca..e506f66657bb 100644
--- a/drivers/media/dvb-frontends/tda1004x.c
+++ b/drivers/media/dvb-frontends/tda1004x.c
@@ -329,7 +329,7 @@ static int tda1004x_do_upload(struct tda1004x_state *state,
 	tda1004x_write_byteI(state, dspCodeCounterReg, 0);
 	fw_msg.addr = state->config->demod_address;
 
-	i2c_lock_adapter(state->i2c);
+	i2c_lock_bus(state->i2c, I2C_LOCK_SEGMENT);
 	buf[0] = dspCodeInReg;
 	while (pos != len) {
 		// work out how much to send this time
@@ -342,14 +342,14 @@ static int tda1004x_do_upload(struct tda1004x_state *state,
 		fw_msg.len = tx_size + 1;
 		if (__i2c_transfer(state->i2c, &fw_msg, 1) != 1) {
 			printk(KERN_ERR "tda1004x: Error during firmware upload\n");
-			i2c_unlock_adapter(state->i2c);
+			i2c_unlock_bus(state->i2c, I2C_LOCK_SEGMENT);
 			return -EIO;
 		}
 		pos += tx_size;
 
 		dprintk("%s: fw_pos=0x%x\n", __func__, pos);
 	}
-	i2c_unlock_adapter(state->i2c);
+	i2c_unlock_bus(state->i2c, I2C_LOCK_SEGMENT);
 
 	/* give the DSP a chance to settle 03/10/05 Hac */
 	msleep(100);
diff --git a/drivers/media/tuners/tda18271-common.c b/drivers/media/tuners/tda18271-common.c
index 7e81cd887c13..054b3b747dae 100644
--- a/drivers/media/tuners/tda18271-common.c
+++ b/drivers/media/tuners/tda18271-common.c
@@ -225,7 +225,7 @@ static int __tda18271_write_regs(struct dvb_frontend *fe, int idx, int len,
 	 */
 	if (lock_i2c) {
 		tda18271_i2c_gate_ctrl(fe, 1);
-		i2c_lock_adapter(priv->i2c_props.adap);
+		i2c_lock_bus(priv->i2c_props.adap, I2C_LOCK_SEGMENT);
 	}
 	while (len) {
 		if (max > len)
@@ -246,7 +246,7 @@ static int __tda18271_write_regs(struct dvb_frontend *fe, int idx, int len,
 		len -= max;
 	}
 	if (lock_i2c) {
-		i2c_unlock_adapter(priv->i2c_props.adap);
+		i2c_unlock_bus(priv->i2c_props.adap, I2C_LOCK_SEGMENT);
 		tda18271_i2c_gate_ctrl(fe, 0);
 	}
 
@@ -300,7 +300,7 @@ int tda18271_init_regs(struct dvb_frontend *fe)
 	 * as those could cause bad things
 	 */
 	tda18271_i2c_gate_ctrl(fe, 1);
-	i2c_lock_adapter(priv->i2c_props.adap);
+	i2c_lock_bus(priv->i2c_props.adap, I2C_LOCK_SEGMENT);
 
 	/* initialize registers */
 	switch (priv->id) {
@@ -516,7 +516,7 @@ int tda18271_init_regs(struct dvb_frontend *fe)
 	/* synchronize */
 	__tda18271_write_regs(fe, R_EP1, 1, false);
 
-	i2c_unlock_adapter(priv->i2c_props.adap);
+	i2c_unlock_bus(priv->i2c_props.adap, I2C_LOCK_SEGMENT);
 	tda18271_i2c_gate_ctrl(fe, 0);
 
 	return 0;
diff --git a/drivers/mfd/88pm860x-i2c.c b/drivers/mfd/88pm860x-i2c.c
index 84e313107233..7b9052ea7413 100644
--- a/drivers/mfd/88pm860x-i2c.c
+++ b/drivers/mfd/88pm860x-i2c.c
@@ -146,14 +146,14 @@ int pm860x_page_reg_write(struct i2c_client *i2c, int reg,
 	unsigned char zero;
 	int ret;
 
-	i2c_lock_adapter(i2c->adapter);
+	i2c_lock_bus(i2c->adapter, I2C_LOCK_SEGMENT);
 	read_device(i2c, 0xFA, 0, &zero);
 	read_device(i2c, 0xFB, 0, &zero);
 	read_device(i2c, 0xFF, 0, &zero);
 	ret = write_device(i2c, reg, 1, &data);
 	read_device(i2c, 0xFE, 0, &zero);
 	read_device(i2c, 0xFC, 0, &zero);
-	i2c_unlock_adapter(i2c->adapter);
+	i2c_unlock_bus(i2c->adapter, I2C_LOCK_SEGMENT);
 	return ret;
 }
 EXPORT_SYMBOL(pm860x_page_reg_write);
@@ -164,14 +164,14 @@ int pm860x_page_bulk_read(struct i2c_client *i2c, int reg,
 	unsigned char zero = 0;
 	int ret;
 
-	i2c_lock_adapter(i2c->adapter);
+	i2c_lock_bus(i2c->adapter, I2C_LOCK_SEGMENT);
 	read_device(i2c, 0xfa, 0, &zero);
 	read_device(i2c, 0xfb, 0, &zero);
 	read_device(i2c, 0xff, 0, &zero);
 	ret = read_device(i2c, reg, count, buf);
 	read_device(i2c, 0xFE, 0, &zero);
 	read_device(i2c, 0xFC, 0, &zero);
-	i2c_unlock_adapter(i2c->adapter);
+	i2c_unlock_bus(i2c->adapter, I2C_LOCK_SEGMENT);
 	return ret;
 }
 EXPORT_SYMBOL(pm860x_page_bulk_read);
diff --git a/drivers/misc/eeprom/at24.c b/drivers/misc/eeprom/at24.c
index f5cc517d1131..7e50e1d6f58c 100644
--- a/drivers/misc/eeprom/at24.c
+++ b/drivers/misc/eeprom/at24.c
@@ -478,6 +478,23 @@ static void at24_properties_to_pdata(struct device *dev,
 	if (device_property_present(dev, "no-read-rollover"))
 		chip->flags |= AT24_FLAG_NO_RDROL;
 
+	err = device_property_read_u32(dev, "address-width", &val);
+	if (!err) {
+		switch (val) {
+		case 8:
+			if (chip->flags & AT24_FLAG_ADDR16)
+				dev_warn(dev, "Override address width to be 8, while default is 16\n");
+			chip->flags &= ~AT24_FLAG_ADDR16;
+			break;
+		case 16:
+			chip->flags |= AT24_FLAG_ADDR16;
+			break;
+		default:
+			dev_warn(dev, "Bad \"address-width\" property: %u\n",
+				 val);
+		}
+	}
+
 	err = device_property_read_u32(dev, "size", &val);
 	if (!err)
 		chip->byte_len = val;