Merge tag 'ux500-dma40-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers

From Linus Walleij:
This is a set of patches from Lee Jones to start converting
the ux500 to fetch DMA channels from the device tree:
- Full DT support and channel mapping in the DMA40 driver
- Dropping of platform data for migrated devices on the DT
  boot path.

* tag 'ux500-dma40-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (36 commits)
  ARM: ux500: Register Cryp and Hash platform drivers on Snowball
  crypto: ux500/[cryp|hash] - Show successful start-up in the bootlog
  ARM: ux500: Stop passing Cryp DMA channel config information though pdata
  crypto: ux500/cryp - Set DMA configuration though dma_slave_config()
  crypto: ux500/cryp - Prepare clock before enabling it
  ARM: ux500: Stop passing Hash DMA channel config information though pdata
  crypto: ux500/hash - Set DMA configuration though dma_slave_config()
  crypto: ux500/hash - Prepare clock before enabling it
  ARM: ux500: Remove unnecessary attributes from DMA channel request pdata
  dmaengine: ste_dma40: Correct copy/paste error
  ARM: ux500: Remove DMA address look-up table
  dmaengine: ste_dma40: Remove redundant address fetching function
  dmaengine: ste_dma40: Only use addresses passed as configuration information
  ARM: ux500: Stop passing UART's platform data for Device Tree boots
  dmaengine: ste_dma40: Don't configure runtime configurable setup during allocate
  dmaengine: ste_dma40: Remove unnecessary call to d40_phy_cfg()
  dmaengine: ste_dma40: Separate Logical Global Interrupt Mask (GIM) unmasking
  ARM: ux500: Pass remnant platform data though to DMA40 driver
  dmaengine: ste_dma40: Supply full Device Tree parsing support
  dmaengine: ste_dma40: Allow driver to be probe()able when DT is enabled
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>

7 files changed, 322 insertions, 220 deletions

diff --git a/drivers/crypto/ux500/cryp/cryp.h b/drivers/crypto/ux500/cryp/cryp.h
index 14cfd05b777a..d1d6606fe56c 100644
--- a/drivers/crypto/ux500/cryp/cryp.h
+++ b/drivers/crypto/ux500/cryp/cryp.h
@@ -114,6 +114,9 @@ enum cryp_status_id {
 };
 
 /* Cryp DMA interface */
+#define CRYP_DMA_TX_FIFO	0x08
+#define CRYP_DMA_RX_FIFO	0x10
+
 enum cryp_dma_req_type {
 	CRYP_DMA_DISABLE_BOTH,
 	CRYP_DMA_ENABLE_IN_DATA,
@@ -217,7 +220,8 @@ struct cryp_dma {
 
 /**
  * struct cryp_device_data - structure for a cryp device.
- * @base: Pointer to the hardware base address.
+ * @base: Pointer to virtual base address of the cryp device.
+ * @phybase: Pointer to physical memory location of the cryp device.
  * @dev: Pointer to the devices dev structure.
  * @clk: Pointer to the device's clock control.
  * @pwr_regulator: Pointer to the device's power control.
@@ -232,6 +236,7 @@ struct cryp_dma {
  */
 struct cryp_device_data {
 	struct cryp_register __iomem *base;
+	phys_addr_t phybase;
 	struct device *dev;
 	struct clk *clk;
 	struct regulator *pwr_regulator;
diff --git a/drivers/crypto/ux500/cryp/cryp_core.c b/drivers/crypto/ux500/cryp/cryp_core.c
index 32f480622b97..4f8b11af29a6 100644
--- a/drivers/crypto/ux500/cryp/cryp_core.c
+++ b/drivers/crypto/ux500/cryp/cryp_core.c
@@ -475,6 +475,19 @@ static int cryp_get_device_data(struct cryp_ctx *ctx,
 static void cryp_dma_setup_channel(struct cryp_device_data *device_data,
 				   struct device *dev)
 {
+	struct dma_slave_config mem2cryp = {
+		.direction = DMA_MEM_TO_DEV,
+		.dst_addr = device_data->phybase + CRYP_DMA_TX_FIFO,
+		.dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES,
+		.dst_maxburst = 4,
+        };
+	struct dma_slave_config cryp2mem = {
+		.direction = DMA_DEV_TO_MEM,
+		.src_addr = device_data->phybase + CRYP_DMA_RX_FIFO,
+		.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES,
+		.src_maxburst = 4,
+        };
+
 	dma_cap_zero(device_data->dma.mask);
 	dma_cap_set(DMA_SLAVE, device_data->dma.mask);
 
@@ -490,6 +503,9 @@ static void cryp_dma_setup_channel(struct cryp_device_data *device_data,
 				    stedma40_filter,
 				    device_data->dma.cfg_cryp2mem);
 
+	dmaengine_slave_config(device_data->dma.chan_mem2cryp, &mem2cryp);
+	dmaengine_slave_config(device_data->dma.chan_cryp2mem, &cryp2mem);
+
 	init_completion(&device_data->dma.cryp_dma_complete);
 }
 
@@ -1431,6 +1447,7 @@ static int ux500_cryp_probe(struct platform_device *pdev)
 		goto out_kfree;
 	}
 
+	device_data->phybase = res->start;
 	device_data->base = ioremap(res->start, resource_size(res));
 	if (!device_data->base) {
 		dev_err(dev, "[%s]: ioremap failed!", __func__);
@@ -1458,11 +1475,17 @@ static int ux500_cryp_probe(struct platform_device *pdev)
 		goto out_regulator;
 	}
 
+	ret = clk_prepare(device_data->clk);
+	if (ret) {
+		dev_err(dev, "[%s]: clk_prepare() failed!", __func__);
+		goto out_clk;
+	}
+
 	/* Enable device power (and clock) */
 	ret = cryp_enable_power(device_data->dev, device_data, false);
 	if (ret) {
 		dev_err(dev, "[%s]: cryp_enable_power() failed!", __func__);
-		goto out_clk;
+		goto out_clk_unprepare;
 	}
 
 	cryp_error = cryp_check(device_data);
@@ -1518,11 +1541,16 @@ static int ux500_cryp_probe(struct platform_device *pdev)
 		goto out_power;
 	}
 
+	dev_info(dev, "successfully registered\n");
+
 	return 0;
 
 out_power:
 	cryp_disable_power(device_data->dev, device_data, false);
 
+out_clk_unprepare:
+	clk_unprepare(device_data->clk);
+
 out_clk:
 	clk_put(device_data->clk);
 
@@ -1593,6 +1621,7 @@ static int ux500_cryp_remove(struct platform_device *pdev)
 		dev_err(&pdev->dev, "[%s]: cryp_disable_power() failed",
 			__func__);
 
+	clk_unprepare(device_data->clk);
 	clk_put(device_data->clk);
 	regulator_put(device_data->pwr_regulator);
 
diff --git a/drivers/crypto/ux500/hash/hash_alg.h b/drivers/crypto/ux500/hash/hash_alg.h
index cd9351cb24df..be6eb54da40f 100644
--- a/drivers/crypto/ux500/hash/hash_alg.h
+++ b/drivers/crypto/ux500/hash/hash_alg.h
@@ -11,6 +11,7 @@
 #include <linux/bitops.h>
 
 #define HASH_BLOCK_SIZE			64
+#define HASH_DMA_FIFO			4
 #define HASH_DMA_ALIGN_SIZE		4
 #define HASH_DMA_PERFORMANCE_MIN_SIZE	1024
 #define HASH_BYTES_PER_WORD		4
@@ -347,7 +348,8 @@ struct hash_req_ctx {
 
 /**
  * struct hash_device_data - structure for a hash device.
- * @base:		Pointer to the hardware base address.
+ * @base:		Pointer to virtual base address of the hash device.
+ * @phybase:		Pointer to physical memory location of the hash device.
  * @list_node:		For inclusion in klist.
  * @dev:		Pointer to the device dev structure.
  * @ctx_lock:		Spinlock for current_ctx.
@@ -361,6 +363,7 @@ struct hash_req_ctx {
  */
 struct hash_device_data {
 	struct hash_register __iomem	*base;
+	phys_addr_t             phybase;
 	struct klist_node	list_node;
 	struct device		*dev;
 	struct spinlock		ctx_lock;
diff --git a/drivers/crypto/ux500/hash/hash_core.c b/drivers/crypto/ux500/hash/hash_core.c
index cf5508967539..9ca6fbb5e30d 100644
--- a/drivers/crypto/ux500/hash/hash_core.c
+++ b/drivers/crypto/ux500/hash/hash_core.c
@@ -122,6 +122,13 @@ static void hash_dma_setup_channel(struct hash_device_data *device_data,
 				struct device *dev)
 {
 	struct hash_platform_data *platform_data = dev->platform_data;
+	struct dma_slave_config conf = {
+		.direction = DMA_MEM_TO_DEV,
+		.dst_addr = device_data->phybase + HASH_DMA_FIFO,
+		.dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES,
+		.dst_maxburst = 16,
+        };
+
 	dma_cap_zero(device_data->dma.mask);
 	dma_cap_set(DMA_SLAVE, device_data->dma.mask);
 
@@ -131,6 +138,8 @@ static void hash_dma_setup_channel(struct hash_device_data *device_data,
 				platform_data->dma_filter,
 				device_data->dma.cfg_mem2hash);
 
+	dmaengine_slave_config(device_data->dma.chan_mem2hash, &conf);
+
 	init_completion(&device_data->dma.complete);
 }
 
@@ -1699,6 +1708,7 @@ static int ux500_hash_probe(struct platform_device *pdev)
 		goto out_kfree;
 	}
 
+	device_data->phybase = res->start;
 	device_data->base = ioremap(res->start, resource_size(res));
 	if (!device_data->base) {
 		dev_err(dev, "[%s] ioremap() failed!",
@@ -1726,11 +1736,17 @@ static int ux500_hash_probe(struct platform_device *pdev)
 		goto out_regulator;
 	}
 
+	ret = clk_prepare(device_data->clk);
+	if (ret) {
+		dev_err(dev, "[%s] clk_prepare() failed!", __func__);
+		goto out_clk;
+	}
+
 	/* Enable device power (and clock) */
 	ret = hash_enable_power(device_data, false);
 	if (ret) {
 		dev_err(dev, "[%s]: hash_enable_power() failed!", __func__);
-		goto out_clk;
+		goto out_clk_unprepare;
 	}
 
 	ret = hash_check_hw(device_data);
@@ -1756,12 +1772,15 @@ static int ux500_hash_probe(struct platform_device *pdev)
 		goto out_power;
 	}
 
-	dev_info(dev, "[%s] successfully probed\n", __func__);
+	dev_info(dev, "successfully registered\n");
 	return 0;
 
 out_power:
 	hash_disable_power(device_data, false);
 
+out_clk_unprepare:
+	clk_unprepare(device_data->clk);
+
 out_clk:
 	clk_put(device_data->clk);
 
@@ -1826,6 +1845,7 @@ static int ux500_hash_remove(struct platform_device *pdev)
 		dev_err(dev, "[%s]: hash_disable_power() failed",
 			__func__);
 
+	clk_unprepare(device_data->clk);
 	clk_put(device_data->clk);
 	regulator_put(device_data->regulator);
 
diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index 1734feec47b1..6ed775736853 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -17,6 +17,8 @@
 #include <linux/pm.h>
 #include <linux/pm_runtime.h>
 #include <linux/err.h>
+#include <linux/of.h>
+#include <linux/of_dma.h>
 #include <linux/amba/bus.h>
 #include <linux/regulator/consumer.h>
 #include <linux/platform_data/dma-ste-dma40.h>
@@ -45,6 +47,9 @@
 #define D40_LCLA_LINK_PER_EVENT_GRP 128
 #define D40_LCLA_END D40_LCLA_LINK_PER_EVENT_GRP
 
+/* Max number of logical channels per physical channel */
+#define D40_MAX_LOG_CHAN_PER_PHY 32
+
 /* Attempts before giving up to trying to get pages that are aligned */
 #define MAX_LCLA_ALLOC_ATTEMPTS 256
 
@@ -53,7 +58,50 @@
 #define D40_ALLOC_PHY		(1 << 30)
 #define D40_ALLOC_LOG_FREE	0
 
-#define MAX(a, b) (((a) < (b)) ? (b) : (a))
+/* Reserved event lines for memcpy only. */
+#define DB8500_DMA_MEMCPY_EV_0	51
+#define DB8500_DMA_MEMCPY_EV_1	56
+#define DB8500_DMA_MEMCPY_EV_2	57
+#define DB8500_DMA_MEMCPY_EV_3	58
+#define DB8500_DMA_MEMCPY_EV_4	59
+#define DB8500_DMA_MEMCPY_EV_5	60
+
+static int dma40_memcpy_channels[] = {
+	DB8500_DMA_MEMCPY_EV_0,
+	DB8500_DMA_MEMCPY_EV_1,
+	DB8500_DMA_MEMCPY_EV_2,
+	DB8500_DMA_MEMCPY_EV_3,
+	DB8500_DMA_MEMCPY_EV_4,
+	DB8500_DMA_MEMCPY_EV_5,
+};
+
+/* Default configuration for physcial memcpy */
+struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
+	.mode = STEDMA40_MODE_PHYSICAL,
+	.dir = STEDMA40_MEM_TO_MEM,
+
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.src_info.psize = STEDMA40_PSIZE_PHY_1,
+	.src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
+
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.psize = STEDMA40_PSIZE_PHY_1,
+	.dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
+};
+
+/* Default configuration for logical memcpy */
+struct stedma40_chan_cfg dma40_memcpy_conf_log = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_MEM,
+
+	.src_info.data_width = STEDMA40_BYTE_WIDTH,
+	.src_info.psize = STEDMA40_PSIZE_LOG_1,
+	.src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
+
+	.dst_info.data_width = STEDMA40_BYTE_WIDTH,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_1,
+	.dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
+};
 
 /**
  * enum 40_command - The different commands and/or statuses.
@@ -171,6 +219,9 @@ static u32 d40_backup_regs_chan[] = {
 	D40_CHAN_REG_SDLNK,
 };
 
+#define BACKUP_REGS_SZ_MAX ((BACKUP_REGS_SZ_V4A > BACKUP_REGS_SZ_V4B) ? \
+			     BACKUP_REGS_SZ_V4A : BACKUP_REGS_SZ_V4B)
+
 /**
  * struct d40_interrupt_lookup - lookup table for interrupt handler
  *
@@ -534,7 +585,7 @@ struct d40_base {
 	resource_size_t			  lcpa_size;
 	struct kmem_cache		 *desc_slab;
 	u32				  reg_val_backup[BACKUP_REGS_SZ];
-	u32				  reg_val_backup_v4[MAX(BACKUP_REGS_SZ_V4A, BACKUP_REGS_SZ_V4B)];
+	u32				  reg_val_backup_v4[BACKUP_REGS_SZ_MAX];
 	u32				 *reg_val_backup_chan;
 	u16				  gcc_pwr_off_mask;
 	bool				  initialized;
@@ -1257,21 +1308,17 @@ static void __d40_config_set_event(struct d40_chan *d40c,
 static void d40_config_set_event(struct d40_chan *d40c,
 				 enum d40_events event_type)
 {
+	u32 event = D40_TYPE_TO_EVENT(d40c->dma_cfg.dev_type);
+
 	/* Enable event line connected to device (or memcpy) */
 	if ((d40c->dma_cfg.dir ==  STEDMA40_PERIPH_TO_MEM) ||
-	    (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_PERIPH)) {
-		u32 event = D40_TYPE_TO_EVENT(d40c->dma_cfg.src_dev_type);
-
+	    (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_PERIPH))
 		__d40_config_set_event(d40c, event_type, event,
 				       D40_CHAN_REG_SSLNK);
-	}
-
-	if (d40c->dma_cfg.dir !=  STEDMA40_PERIPH_TO_MEM) {
-		u32 event = D40_TYPE_TO_EVENT(d40c->dma_cfg.dst_dev_type);
 
+	if (d40c->dma_cfg.dir !=  STEDMA40_PERIPH_TO_MEM)
 		__d40_config_set_event(d40c, event_type, event,
 				       D40_CHAN_REG_SDLNK);
-	}
 }
 
 static u32 d40_chan_has_events(struct d40_chan *d40c)
@@ -1713,8 +1760,6 @@ static int d40_validate_conf(struct d40_chan *d40c,
 			     struct stedma40_chan_cfg *conf)
 {
 	int res = 0;
-	u32 dst_event_group = D40_TYPE_TO_GROUP(conf->dst_dev_type);
-	u32 src_event_group = D40_TYPE_TO_GROUP(conf->src_dev_type);
 	bool is_log = conf->mode == STEDMA40_MODE_LOGICAL;
 
 	if (!conf->dir) {
@@ -1722,44 +1767,10 @@ static int d40_validate_conf(struct d40_chan *d40c,
 		res = -EINVAL;
 	}
 
-	if (conf->dst_dev_type != STEDMA40_DEV_DST_MEMORY &&
-	    d40c->base->plat_data->dev_tx[conf->dst_dev_type] == 0 &&
-	    d40c->runtime_addr == 0) {
-
-		chan_err(d40c, "Invalid TX channel address (%d)\n",
-			 conf->dst_dev_type);
-		res = -EINVAL;
-	}
-
-	if (conf->src_dev_type != STEDMA40_DEV_SRC_MEMORY &&
-	    d40c->base->plat_data->dev_rx[conf->src_dev_type] == 0 &&
-	    d40c->runtime_addr == 0) {
-		chan_err(d40c, "Invalid RX channel address (%d)\n",
-			conf->src_dev_type);
-		res = -EINVAL;
-	}
-
-	if (conf->dir == STEDMA40_MEM_TO_PERIPH &&
-	    dst_event_group == STEDMA40_DEV_DST_MEMORY) {
-		chan_err(d40c, "Invalid dst\n");
-		res = -EINVAL;
-	}
-
-	if (conf->dir == STEDMA40_PERIPH_TO_MEM &&
-	    src_event_group == STEDMA40_DEV_SRC_MEMORY) {
-		chan_err(d40c, "Invalid src\n");
-		res = -EINVAL;
-	}
-
-	if (src_event_group == STEDMA40_DEV_SRC_MEMORY &&
-	    dst_event_group == STEDMA40_DEV_DST_MEMORY && is_log) {
-		chan_err(d40c, "No event line\n");
-		res = -EINVAL;
-	}
-
-	if (conf->dir == STEDMA40_PERIPH_TO_PERIPH &&
-	    (src_event_group != dst_event_group)) {
-		chan_err(d40c, "Invalid event group\n");
+	if ((is_log && conf->dev_type > d40c->base->num_log_chans)  ||
+	    (!is_log && conf->dev_type > d40c->base->num_phy_chans) ||
+	    (conf->dev_type < 0)) {
+		chan_err(d40c, "Invalid device type (%d)\n", conf->dev_type);
 		res = -EINVAL;
 	}
 
@@ -1880,7 +1891,7 @@ out:
 
 static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 {
-	int dev_type;
+	int dev_type = d40c->dma_cfg.dev_type;
 	int event_group;
 	int event_line;
 	struct d40_phy_res *phys;
@@ -1895,13 +1906,11 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 	num_phy_chans = d40c->base->num_phy_chans;
 
 	if (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM) {
-		dev_type = d40c->dma_cfg.src_dev_type;
 		log_num = 2 * dev_type;
 		is_src = true;
 	} else if (d40c->dma_cfg.dir == STEDMA40_MEM_TO_PERIPH ||
 		   d40c->dma_cfg.dir == STEDMA40_MEM_TO_MEM) {
 		/* dst event lines are used for logical memcpy */
-		dev_type = d40c->dma_cfg.dst_dev_type;
 		log_num = 2 * dev_type + 1;
 		is_src = false;
 	} else
@@ -2012,14 +2021,23 @@ static int d40_config_memcpy(struct d40_chan *d40c)
 	dma_cap_mask_t cap = d40c->chan.device->cap_mask;
 
 	if (dma_has_cap(DMA_MEMCPY, cap) && !dma_has_cap(DMA_SLAVE, cap)) {
-		d40c->dma_cfg = *d40c->base->plat_data->memcpy_conf_log;
-		d40c->dma_cfg.src_dev_type = STEDMA40_DEV_SRC_MEMORY;
-		d40c->dma_cfg.dst_dev_type = d40c->base->plat_data->
-			memcpy[d40c->chan.chan_id];
+		d40c->dma_cfg = dma40_memcpy_conf_log;
+		d40c->dma_cfg.dev_type = dma40_memcpy_channels[d40c->chan.chan_id];
+
+		d40_log_cfg(&d40c->dma_cfg,
+			    &d40c->log_def.lcsp1, &d40c->log_def.lcsp3);
 
 	} else if (dma_has_cap(DMA_MEMCPY, cap) &&
 		   dma_has_cap(DMA_SLAVE, cap)) {
-		d40c->dma_cfg = *d40c->base->plat_data->memcpy_conf_phy;
+		d40c->dma_cfg = dma40_memcpy_conf_phy;
+
+		/* Generate interrrupt at end of transfer or relink. */
+		d40c->dst_def_cfg |= BIT(D40_SREG_CFG_TIM_POS);
+
+		/* Generate interrupt on error. */
+		d40c->src_def_cfg |= BIT(D40_SREG_CFG_EIM_POS);
+		d40c->dst_def_cfg |= BIT(D40_SREG_CFG_EIM_POS);
+
 	} else {
 		chan_err(d40c, "No memcpy\n");
 		return -EINVAL;
@@ -2032,7 +2050,7 @@ static int d40_free_dma(struct d40_chan *d40c)
 {
 
 	int res = 0;
-	u32 event;
+	u32 event = D40_TYPE_TO_EVENT(d40c->dma_cfg.dev_type);
 	struct d40_phy_res *phy = d40c->phy_chan;
 	bool is_src;
 
@@ -2051,13 +2069,11 @@ static int d40_free_dma(struct d40_chan *d40c)
 	}
 
 	if (d40c->dma_cfg.dir == STEDMA40_MEM_TO_PERIPH ||
-	    d40c->dma_cfg.dir == STEDMA40_MEM_TO_MEM) {
-		event = D40_TYPE_TO_EVENT(d40c->dma_cfg.dst_dev_type);
+	    d40c->dma_cfg.dir == STEDMA40_MEM_TO_MEM)
 		is_src = false;
-	} else if (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM) {
-		event = D40_TYPE_TO_EVENT(d40c->dma_cfg.src_dev_type);
+	else if (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM)
 		is_src = true;
-	} else {
+	else {
 		chan_err(d40c, "Unknown direction\n");
 		return -EINVAL;
 	}
@@ -2098,7 +2114,7 @@ static bool d40_is_paused(struct d40_chan *d40c)
 	unsigned long flags;
 	void __iomem *active_reg;
 	u32 status;
-	u32 event;
+	u32 event = D40_TYPE_TO_EVENT(d40c->dma_cfg.dev_type);
 
 	spin_lock_irqsave(&d40c->lock, flags);
 
@@ -2119,10 +2135,8 @@ static bool d40_is_paused(struct d40_chan *d40c)
 
 	if (d40c->dma_cfg.dir == STEDMA40_MEM_TO_PERIPH ||
 	    d40c->dma_cfg.dir == STEDMA40_MEM_TO_MEM) {
-		event = D40_TYPE_TO_EVENT(d40c->dma_cfg.dst_dev_type);
 		status = readl(chanbase + D40_CHAN_REG_SDLNK);
 	} else if (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM) {
-		event = D40_TYPE_TO_EVENT(d40c->dma_cfg.src_dev_type);
 		status = readl(chanbase + D40_CHAN_REG_SSLNK);
 	} else {
 		chan_err(d40c, "Unknown direction\n");
@@ -2253,24 +2267,6 @@ err:
 	return NULL;
 }
 
-static dma_addr_t
-d40_get_dev_addr(struct d40_chan *chan, enum dma_transfer_direction direction)
-{
-	struct stedma40_platform_data *plat = chan->base->plat_data;
-	struct stedma40_chan_cfg *cfg = &chan->dma_cfg;
-	dma_addr_t addr = 0;
-
-	if (chan->runtime_addr)
-		return chan->runtime_addr;
-
-	if (direction == DMA_DEV_TO_MEM)
-		addr = plat->dev_rx[cfg->src_dev_type];
-	else if (direction == DMA_MEM_TO_DEV)
-		addr = plat->dev_tx[cfg->dst_dev_type];
-
-	return addr;
-}
-
 static struct dma_async_tx_descriptor *
 d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,
 	    struct scatterlist *sg_dst, unsigned int sg_len,
@@ -2297,14 +2293,10 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,
 	if (sg_next(&sg_src[sg_len - 1]) == sg_src)
 		desc->cyclic = true;
 
-	if (direction != DMA_TRANS_NONE) {
-		dma_addr_t dev_addr = d40_get_dev_addr(chan, direction);
-
-		if (direction == DMA_DEV_TO_MEM)
-			src_dev_addr = dev_addr;
-		else if (direction == DMA_MEM_TO_DEV)
-			dst_dev_addr = dev_addr;
-	}
+	if (direction == DMA_DEV_TO_MEM)
+		src_dev_addr = chan->runtime_addr;
+	else if (direction == DMA_MEM_TO_DEV)
+		dst_dev_addr = chan->runtime_addr;
 
 	if (chan_is_logical(chan))
 		ret = d40_prep_sg_log(chan, desc, sg_src, sg_dst,
@@ -2397,11 +2389,55 @@ static void d40_set_prio_realtime(struct d40_chan *d40c)
 
 	if ((d40c->dma_cfg.dir ==  STEDMA40_PERIPH_TO_MEM) ||
 	    (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_PERIPH))
-		__d40_set_prio_rt(d40c, d40c->dma_cfg.src_dev_type, true);
+		__d40_set_prio_rt(d40c, d40c->dma_cfg.dev_type, true);
 
 	if ((d40c->dma_cfg.dir ==  STEDMA40_MEM_TO_PERIPH) ||
 	    (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_PERIPH))
-		__d40_set_prio_rt(d40c, d40c->dma_cfg.dst_dev_type, false);
+		__d40_set_prio_rt(d40c, d40c->dma_cfg.dev_type, false);
+}
+
+#define D40_DT_FLAGS_MODE(flags)       ((flags >> 0) & 0x1)
+#define D40_DT_FLAGS_DIR(flags)        ((flags >> 1) & 0x1)
+#define D40_DT_FLAGS_BIG_ENDIAN(flags) ((flags >> 2) & 0x1)
+#define D40_DT_FLAGS_FIXED_CHAN(flags) ((flags >> 3) & 0x1)
+
+static struct dma_chan *d40_xlate(struct of_phandle_args *dma_spec,
+				  struct of_dma *ofdma)
+{
+	struct stedma40_chan_cfg cfg;
+	dma_cap_mask_t cap;
+	u32 flags;
+
+	memset(&cfg, 0, sizeof(struct stedma40_chan_cfg));
+
+	dma_cap_zero(cap);
+	dma_cap_set(DMA_SLAVE, cap);
+
+	cfg.dev_type = dma_spec->args[0];
+	flags = dma_spec->args[2];
+
+	switch (D40_DT_FLAGS_MODE(flags)) {
+	case 0: cfg.mode = STEDMA40_MODE_LOGICAL; break;
+	case 1: cfg.mode = STEDMA40_MODE_PHYSICAL; break;
+	}
+
+	switch (D40_DT_FLAGS_DIR(flags)) {
+	case 0:
+		cfg.dir = STEDMA40_MEM_TO_PERIPH;
+		cfg.dst_info.big_endian = D40_DT_FLAGS_BIG_ENDIAN(flags);
+		break;
+	case 1:
+		cfg.dir = STEDMA40_PERIPH_TO_MEM;
+		cfg.src_info.big_endian = D40_DT_FLAGS_BIG_ENDIAN(flags);
+		break;
+	}
+
+	if (D40_DT_FLAGS_FIXED_CHAN(flags)) {
+		cfg.phy_channel = dma_spec->args[1];
+		cfg.use_fixed_channel = true;
+	}
+
+	return dma_request_channel(cap, stedma40_filter, &cfg);
 }
 
 /* DMA ENGINE functions */
@@ -2433,23 +2469,21 @@ static int d40_alloc_chan_resources(struct dma_chan *chan)
 	}
 
 	pm_runtime_get_sync(d40c->base->dev);
-	/* Fill in basic CFG register values */
-	d40_phy_cfg(&d40c->dma_cfg, &d40c->src_def_cfg,
-		    &d40c->dst_def_cfg, chan_is_logical(d40c));
 
 	d40_set_prio_realtime(d40c);
 
 	if (chan_is_logical(d40c)) {
-		d40_log_cfg(&d40c->dma_cfg,
-			    &d40c->log_def.lcsp1, &d40c->log_def.lcsp3);
-
 		if (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM)
 			d40c->lcpa = d40c->base->lcpa_base +
-				d40c->dma_cfg.src_dev_type * D40_LCPA_CHAN_SIZE;
+				d40c->dma_cfg.dev_type * D40_LCPA_CHAN_SIZE;
 		else
 			d40c->lcpa = d40c->base->lcpa_base +
-				d40c->dma_cfg.dst_dev_type *
+				d40c->dma_cfg.dev_type *
 				D40_LCPA_CHAN_SIZE + D40_LCPA_CHAN_DST_DELTA;
+
+		/* Unmask the Global Interrupt Mask. */
+		d40c->src_def_cfg |= BIT(D40_SREG_CFG_LOG_GIM_POS);
+		d40c->dst_def_cfg |= BIT(D40_SREG_CFG_LOG_GIM_POS);
 	}
 
 	dev_dbg(chan2dev(d40c), "allocated %s channel (phy %d%s)\n",
@@ -2710,15 +2744,8 @@ static int d40_set_runtime_config(struct dma_chan *chan,
 	dst_maxburst = config->dst_maxburst;
 
 	if (config->direction == DMA_DEV_TO_MEM) {
-		dma_addr_t dev_addr_rx =
-			d40c->base->plat_data->dev_rx[cfg->src_dev_type];
-
 		config_addr = config->src_addr;
-		if (dev_addr_rx)
-			dev_dbg(d40c->base->dev,
-				"channel has a pre-wired RX address %08x "
-				"overriding with %08x\n",
-				dev_addr_rx, config_addr);
+
 		if (cfg->dir != STEDMA40_PERIPH_TO_MEM)
 			dev_dbg(d40c->base->dev,
 				"channel was not configured for peripheral "
@@ -2733,15 +2760,8 @@ static int d40_set_runtime_config(struct dma_chan *chan,
 			dst_maxburst = src_maxburst;
 
 	} else if (config->direction == DMA_MEM_TO_DEV) {
-		dma_addr_t dev_addr_tx =
-			d40c->base->plat_data->dev_tx[cfg->dst_dev_type];
-
 		config_addr = config->dst_addr;
-		if (dev_addr_tx)
-			dev_dbg(d40c->base->dev,
-				"channel has a pre-wired TX address %08x "
-				"overriding with %08x\n",
-				dev_addr_tx, config_addr);
+
 		if (cfg->dir != STEDMA40_MEM_TO_PERIPH)
 			dev_dbg(d40c->base->dev,
 				"channel was not configured for memory "
@@ -2761,6 +2781,11 @@ static int d40_set_runtime_config(struct dma_chan *chan,
 		return -EINVAL;
 	}
 
+	if (config_addr <= 0) {
+		dev_err(d40c->base->dev, "no address supplied\n");
+		return -EINVAL;
+	}
+
 	if (src_maxburst * src_addr_width != dst_maxburst * dst_addr_width) {
 		dev_err(d40c->base->dev,
 			"src/dst width/maxburst mismatch: %d*%d != %d*%d\n",
@@ -2795,8 +2820,7 @@ static int d40_set_runtime_config(struct dma_chan *chan,
 	if (chan_is_logical(d40c))
 		d40_log_cfg(cfg, &d40c->log_def.lcsp1, &d40c->log_def.lcsp3);
 	else
-		d40_phy_cfg(cfg, &d40c->src_def_cfg,
-			    &d40c->dst_def_cfg, false);
+		d40_phy_cfg(cfg, &d40c->src_def_cfg, &d40c->dst_def_cfg);
 
 	/* These settings will take precedence later */
 	d40c->runtime_addr = config_addr;
@@ -2927,7 +2951,7 @@ static int __init d40_dmaengine_init(struct d40_base *base,
 	}
 
 	d40_chan_init(base, &base->dma_memcpy, base->log_chans,
-		      base->num_log_chans, base->plat_data->memcpy_len);
+		      base->num_log_chans, ARRAY_SIZE(dma40_memcpy_channels));
 
 	dma_cap_zero(base->dma_memcpy.cap_mask);
 	dma_cap_set(DMA_MEMCPY, base->dma_memcpy.cap_mask);
@@ -3121,7 +3145,7 @@ static int __init d40_phy_res_init(struct d40_base *base)
 
 static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
 {
-	struct stedma40_platform_data *plat_data;
+	struct stedma40_platform_data *plat_data = pdev->dev.platform_data;
 	struct clk *clk = NULL;
 	void __iomem *virtbase = NULL;
 	struct resource *res = NULL;
@@ -3187,8 +3211,10 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
 	 * DB8540v1 has revision 4
 	 */
 	rev = AMBA_REV_BITS(pid);
-
-	plat_data = pdev->dev.platform_data;
+	if (rev < 2) {
+		d40_err(&pdev->dev, "hardware revision: %d is not supported", rev);
+		goto failure;
+	}
 
 	/* The number of physical channels on this HW */
 	if (plat_data->num_of_phy_chans)
@@ -3196,26 +3222,14 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
 	else
 		num_phy_chans = 4 * (readl(virtbase + D40_DREG_ICFG) & 0x7) + 4;
 
-	dev_info(&pdev->dev, "hardware revision: %d @ 0x%x with %d physical channels\n",
-		 rev, res->start, num_phy_chans);
-
-	if (rev < 2) {
-		d40_err(&pdev->dev, "hardware revision: %d is not supported",
-			rev);
-		goto failure;
-	}
+	num_log_chans = num_phy_chans * D40_MAX_LOG_CHAN_PER_PHY;
 
-	/* Count the number of logical channels in use */
-	for (i = 0; i < plat_data->dev_len; i++)
-		if (plat_data->dev_rx[i] != 0)
-			num_log_chans++;
-
-	for (i = 0; i < plat_data->dev_len; i++)
-		if (plat_data->dev_tx[i] != 0)
-			num_log_chans++;
+	dev_info(&pdev->dev,
+		 "hardware rev: %d @ 0x%x with %d physical and %d logical channels\n",
+		 rev, res->start, num_phy_chans, num_log_chans);
 
 	base = kzalloc(ALIGN(sizeof(struct d40_base), 4) +
-		       (num_phy_chans + num_log_chans + plat_data->memcpy_len) *
+		       (num_phy_chans + num_log_chans + ARRAY_SIZE(dma40_memcpy_channels)) *
 		       sizeof(struct d40_chan), GFP_KERNEL);
 
 	if (base == NULL) {
@@ -3276,17 +3290,11 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
 	if (!base->lookup_phy_chans)
 		goto failure;
 
-	if (num_log_chans + plat_data->memcpy_len) {
-		/*
-		 * The max number of logical channels are event lines for all
-		 * src devices and dst devices
-		 */
-		base->lookup_log_chans = kzalloc(plat_data->dev_len * 2 *
-						 sizeof(struct d40_chan *),
-						 GFP_KERNEL);
-		if (!base->lookup_log_chans)
-			goto failure;
-	}
+	base->lookup_log_chans = kzalloc(num_log_chans *
+					 sizeof(struct d40_chan *),
+					 GFP_KERNEL);
+	if (!base->lookup_log_chans)
+		goto failure;
 
 	base->reg_val_backup_chan = kmalloc(base->num_phy_chans *
 					    sizeof(d40_backup_regs_chan),
@@ -3470,17 +3478,52 @@ failure:
 	return ret;
 }
 
+static int __init d40_of_probe(struct platform_device *pdev,
+			       struct device_node *np)
+{
+	struct stedma40_platform_data *pdata;
+
+	/*
+	 * FIXME: Fill in this routine as more support is added.
+	 * First platform enabled (u8500) doens't need any extra
+	 * properties to run, so this is fairly sparce currently.
+	 */
+
+	pdata = devm_kzalloc(&pdev->dev,
+			     sizeof(struct stedma40_platform_data),
+			     GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	pdev->dev.platform_data = pdata;
+
+	return 0;
+}
+
 static int __init d40_probe(struct platform_device *pdev)
 {
+	struct stedma40_platform_data *plat_data = pdev->dev.platform_data;
+	struct device_node *np = pdev->dev.of_node;
 	int err;
 	int ret = -ENOENT;
-	struct d40_base *base;
+	struct d40_base *base = NULL;
 	struct resource *res = NULL;
 	int num_reserved_chans;
 	u32 val;
 
-	base = d40_hw_detect_init(pdev);
+	if (!plat_data) {
+		if (np) {
+			if(d40_of_probe(pdev, np)) {
+				ret = -ENOMEM;
+				goto failure;
+			}
+		} else {
+			d40_err(&pdev->dev, "No pdata or Device Tree provided\n");
+			goto failure;
+		}
+	}
 
+	base = d40_hw_detect_init(pdev);
 	if (!base)
 		goto failure;
 
@@ -3601,6 +3644,13 @@ static int __init d40_probe(struct platform_device *pdev)
 
 	d40_hw_init(base);
 
+	if (np) {
+		err = of_dma_controller_register(np, d40_xlate, NULL);
+		if (err && err != -ENODEV)
+			dev_err(&pdev->dev,
+				"could not register of_dma_controller\n");
+	}
+
 	dev_info(base->dev, "initialized\n");
 	return 0;
 
@@ -3654,11 +3704,17 @@ failure:
 	return ret;
 }
 
+static const struct of_device_id d40_match[] = {
+        { .compatible = "stericsson,dma40", },
+        {}
+};
+
 static struct platform_driver d40_driver = {
 	.driver = {
 		.owner = THIS_MODULE,
 		.name  = D40_NAME,
 		.pm = DMA40_PM_OPS,
+		.of_match_table = d40_match,
 	},
 };
 
diff --git a/drivers/dma/ste_dma40_ll.c b/drivers/dma/ste_dma40_ll.c
index 7180e0d41722..ab5a2a706f7a 100644
--- a/drivers/dma/ste_dma40_ll.c
+++ b/drivers/dma/ste_dma40_ll.c
@@ -50,68 +50,58 @@ void d40_log_cfg(struct stedma40_chan_cfg *cfg,
 
 }
 
-/* Sets up SRC and DST CFG register for both logical and physical channels */
-void d40_phy_cfg(struct stedma40_chan_cfg *cfg,
-		 u32 *src_cfg, u32 *dst_cfg, bool is_log)
+void d40_phy_cfg(struct stedma40_chan_cfg *cfg, u32 *src_cfg, u32 *dst_cfg)
 {
 	u32 src = 0;
 	u32 dst = 0;
 
-	if (!is_log) {
-		/* Physical channel */
-		if ((cfg->dir ==  STEDMA40_PERIPH_TO_MEM) ||
-		    (cfg->dir == STEDMA40_PERIPH_TO_PERIPH)) {
-			/* Set master port to 1 */
-			src |= 1 << D40_SREG_CFG_MST_POS;
-			src |= D40_TYPE_TO_EVENT(cfg->src_dev_type);
-
-			if (cfg->src_info.flow_ctrl == STEDMA40_NO_FLOW_CTRL)
-				src |= 1 << D40_SREG_CFG_PHY_TM_POS;
-			else
-				src |= 3 << D40_SREG_CFG_PHY_TM_POS;
-		}
-		if ((cfg->dir ==  STEDMA40_MEM_TO_PERIPH) ||
-		    (cfg->dir == STEDMA40_PERIPH_TO_PERIPH)) {
-			/* Set master port to 1 */
-			dst |= 1 << D40_SREG_CFG_MST_POS;
-			dst |= D40_TYPE_TO_EVENT(cfg->dst_dev_type);
-
-			if (cfg->dst_info.flow_ctrl == STEDMA40_NO_FLOW_CTRL)
-				dst |= 1 << D40_SREG_CFG_PHY_TM_POS;
-			else
-				dst |= 3 << D40_SREG_CFG_PHY_TM_POS;
-		}
-		/* Interrupt on end of transfer for destination */
-		dst |= 1 << D40_SREG_CFG_TIM_POS;
-
-		/* Generate interrupt on error */
-		src |= 1 << D40_SREG_CFG_EIM_POS;
-		dst |= 1 << D40_SREG_CFG_EIM_POS;
-
-		/* PSIZE */
-		if (cfg->src_info.psize != STEDMA40_PSIZE_PHY_1) {
-			src |= 1 << D40_SREG_CFG_PHY_PEN_POS;
-			src |= cfg->src_info.psize << D40_SREG_CFG_PSIZE_POS;
-		}
-		if (cfg->dst_info.psize != STEDMA40_PSIZE_PHY_1) {
-			dst |= 1 << D40_SREG_CFG_PHY_PEN_POS;
-			dst |= cfg->dst_info.psize << D40_SREG_CFG_PSIZE_POS;
-		}
-
-		/* Element size */
-		src |= cfg->src_info.data_width << D40_SREG_CFG_ESIZE_POS;
-		dst |= cfg->dst_info.data_width << D40_SREG_CFG_ESIZE_POS;
-
-		/* Set the priority bit to high for the physical channel */
-		if (cfg->high_priority) {
-			src |= 1 << D40_SREG_CFG_PRI_POS;
-			dst |= 1 << D40_SREG_CFG_PRI_POS;
-		}
-
-	} else {
-		/* Logical channel */
-		dst |= 1 << D40_SREG_CFG_LOG_GIM_POS;
-		src |= 1 << D40_SREG_CFG_LOG_GIM_POS;
+	if ((cfg->dir ==  STEDMA40_PERIPH_TO_MEM) ||
+	    (cfg->dir == STEDMA40_PERIPH_TO_PERIPH)) {
+		/* Set master port to 1 */
+		src |= 1 << D40_SREG_CFG_MST_POS;
+		src |= D40_TYPE_TO_EVENT(cfg->dev_type);
+
+		if (cfg->src_info.flow_ctrl == STEDMA40_NO_FLOW_CTRL)
+			src |= 1 << D40_SREG_CFG_PHY_TM_POS;
+		else
+			src |= 3 << D40_SREG_CFG_PHY_TM_POS;
+	}
+	if ((cfg->dir ==  STEDMA40_MEM_TO_PERIPH) ||
+	    (cfg->dir == STEDMA40_PERIPH_TO_PERIPH)) {
+		/* Set master port to 1 */
+		dst |= 1 << D40_SREG_CFG_MST_POS;
+		dst |= D40_TYPE_TO_EVENT(cfg->dev_type);
+
+		if (cfg->dst_info.flow_ctrl == STEDMA40_NO_FLOW_CTRL)
+			dst |= 1 << D40_SREG_CFG_PHY_TM_POS;
+		else
+			dst |= 3 << D40_SREG_CFG_PHY_TM_POS;
+	}
+	/* Interrupt on end of transfer for destination */
+	dst |= 1 << D40_SREG_CFG_TIM_POS;
+
+	/* Generate interrupt on error */
+	src |= 1 << D40_SREG_CFG_EIM_POS;
+	dst |= 1 << D40_SREG_CFG_EIM_POS;
+
+	/* PSIZE */
+	if (cfg->src_info.psize != STEDMA40_PSIZE_PHY_1) {
+		src |= 1 << D40_SREG_CFG_PHY_PEN_POS;
+		src |= cfg->src_info.psize << D40_SREG_CFG_PSIZE_POS;
+	}
+	if (cfg->dst_info.psize != STEDMA40_PSIZE_PHY_1) {
+		dst |= 1 << D40_SREG_CFG_PHY_PEN_POS;
+		dst |= cfg->dst_info.psize << D40_SREG_CFG_PSIZE_POS;
+	}
+
+	/* Element size */
+	src |= cfg->src_info.data_width << D40_SREG_CFG_ESIZE_POS;
+	dst |= cfg->dst_info.data_width << D40_SREG_CFG_ESIZE_POS;
+
+	/* Set the priority bit to high for the physical channel */
+	if (cfg->high_priority) {
+		src |= 1 << D40_SREG_CFG_PRI_POS;
+		dst |= 1 << D40_SREG_CFG_PRI_POS;
 	}
 
 	if (cfg->src_info.big_endian)
diff --git a/drivers/dma/ste_dma40_ll.h b/drivers/dma/ste_dma40_ll.h
index fdde8ef77542..1b47312bc574 100644
--- a/drivers/dma/ste_dma40_ll.h
+++ b/drivers/dma/ste_dma40_ll.h
@@ -432,8 +432,7 @@ enum d40_lli_flags {
 
 void d40_phy_cfg(struct stedma40_chan_cfg *cfg,
 		 u32 *src_cfg,
-		 u32 *dst_cfg,
-		 bool is_log);
+		 u32 *dst_cfg);
 
 void d40_log_cfg(struct stedma40_chan_cfg *cfg,
 		 u32 *lcsp1,