[PATCH] USB: linux/usb/net2280.h common definitions

Move common definitions for NET2280 to <linux/usb/net2280.h>, so that I can
use them in prism54usb (it is not merged yet, but I plan to do it soon).

Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 1 insertions, 416 deletions

diff --git a/drivers/usb/gadget/net2280.h b/drivers/usb/gadget/net2280.h
index e195abec8d7f..957d6df34015 100644
--- a/drivers/usb/gadget/net2280.h
+++ b/drivers/usb/gadget/net2280.h
@@ -22,422 +22,7 @@
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 
-/*-------------------------------------------------------------------------*/
-
-/* NET2280 MEMORY MAPPED REGISTERS
- *
- * The register layout came from the chip documentation, and the bit
- * number definitions were extracted from chip specification.
- *
- * Use the shift operator ('<<') to build bit masks, with readl/writel
- * to access the registers through PCI.
- */
-
-/* main registers, BAR0 + 0x0000 */
-struct net2280_regs {
-	// offset 0x0000
-	u32		devinit;
-#define     LOCAL_CLOCK_FREQUENCY                               8
-#define     FORCE_PCI_RESET                                     7
-#define     PCI_ID                                              6
-#define     PCI_ENABLE                                          5
-#define     FIFO_SOFT_RESET                                     4
-#define     CFG_SOFT_RESET                                      3
-#define     PCI_SOFT_RESET                                      2
-#define     USB_SOFT_RESET                                      1
-#define     M8051_RESET                                         0
-	u32		eectl;
-#define     EEPROM_ADDRESS_WIDTH                                23
-#define     EEPROM_CHIP_SELECT_ACTIVE                           22
-#define     EEPROM_PRESENT                                      21
-#define     EEPROM_VALID                                        20
-#define     EEPROM_BUSY                                         19
-#define     EEPROM_CHIP_SELECT_ENABLE                           18
-#define     EEPROM_BYTE_READ_START                              17
-#define     EEPROM_BYTE_WRITE_START                             16
-#define     EEPROM_READ_DATA                                    8
-#define     EEPROM_WRITE_DATA                                   0
-	u32		eeclkfreq;
-	u32		_unused0;
-	// offset 0x0010
-
-	u32		pciirqenb0;		/* interrupt PCI master ... */
-#define     SETUP_PACKET_INTERRUPT_ENABLE                       7
-#define     ENDPOINT_F_INTERRUPT_ENABLE                         6
-#define     ENDPOINT_E_INTERRUPT_ENABLE                         5
-#define     ENDPOINT_D_INTERRUPT_ENABLE                         4
-#define     ENDPOINT_C_INTERRUPT_ENABLE                         3
-#define     ENDPOINT_B_INTERRUPT_ENABLE                         2
-#define     ENDPOINT_A_INTERRUPT_ENABLE                         1
-#define     ENDPOINT_0_INTERRUPT_ENABLE                         0
-	u32		pciirqenb1;
-#define     PCI_INTERRUPT_ENABLE                                31
-#define     POWER_STATE_CHANGE_INTERRUPT_ENABLE                 27
-#define     PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE                26
-#define     PCI_PARITY_ERROR_INTERRUPT_ENABLE                   25
-#define     PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE          20
-#define     PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE          19
-#define     PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE          18
-#define     PCI_RETRY_ABORT_INTERRUPT_ENABLE                    17
-#define     PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE              16
-#define     GPIO_INTERRUPT_ENABLE                               13
-#define     DMA_D_INTERRUPT_ENABLE                              12
-#define     DMA_C_INTERRUPT_ENABLE                              11
-#define     DMA_B_INTERRUPT_ENABLE                              10
-#define     DMA_A_INTERRUPT_ENABLE                              9
-#define     EEPROM_DONE_INTERRUPT_ENABLE                        8
-#define     VBUS_INTERRUPT_ENABLE                               7
-#define     CONTROL_STATUS_INTERRUPT_ENABLE                     6
-#define     ROOT_PORT_RESET_INTERRUPT_ENABLE                    4
-#define     SUSPEND_REQUEST_INTERRUPT_ENABLE                    3
-#define     SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE             2
-#define     RESUME_INTERRUPT_ENABLE                             1
-#define     SOF_INTERRUPT_ENABLE                                0
-	u32		cpu_irqenb0;		/* ... or onboard 8051 */
-#define     SETUP_PACKET_INTERRUPT_ENABLE                       7
-#define     ENDPOINT_F_INTERRUPT_ENABLE                         6
-#define     ENDPOINT_E_INTERRUPT_ENABLE                         5
-#define     ENDPOINT_D_INTERRUPT_ENABLE                         4
-#define     ENDPOINT_C_INTERRUPT_ENABLE                         3
-#define     ENDPOINT_B_INTERRUPT_ENABLE                         2
-#define     ENDPOINT_A_INTERRUPT_ENABLE                         1
-#define     ENDPOINT_0_INTERRUPT_ENABLE                         0
-	u32		cpu_irqenb1;
-#define     CPU_INTERRUPT_ENABLE                                31
-#define     POWER_STATE_CHANGE_INTERRUPT_ENABLE                 27
-#define     PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE                26
-#define     PCI_PARITY_ERROR_INTERRUPT_ENABLE                   25
-#define     PCI_INTA_INTERRUPT_ENABLE                           24
-#define     PCI_PME_INTERRUPT_ENABLE                            23
-#define     PCI_SERR_INTERRUPT_ENABLE                           22
-#define     PCI_PERR_INTERRUPT_ENABLE                           21
-#define     PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE          20
-#define     PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE          19
-#define     PCI_RETRY_ABORT_INTERRUPT_ENABLE                    17
-#define     PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE              16
-#define     GPIO_INTERRUPT_ENABLE                               13
-#define     DMA_D_INTERRUPT_ENABLE                              12
-#define     DMA_C_INTERRUPT_ENABLE                              11
-#define     DMA_B_INTERRUPT_ENABLE                              10
-#define     DMA_A_INTERRUPT_ENABLE                              9
-#define     EEPROM_DONE_INTERRUPT_ENABLE                        8
-#define     VBUS_INTERRUPT_ENABLE                               7
-#define     CONTROL_STATUS_INTERRUPT_ENABLE                     6
-#define     ROOT_PORT_RESET_INTERRUPT_ENABLE                    4
-#define     SUSPEND_REQUEST_INTERRUPT_ENABLE                    3
-#define     SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE             2
-#define     RESUME_INTERRUPT_ENABLE                             1
-#define     SOF_INTERRUPT_ENABLE                                0
-
-	// offset 0x0020
-	u32		_unused1;
-	u32		usbirqenb1;
-#define     USB_INTERRUPT_ENABLE                                31
-#define     POWER_STATE_CHANGE_INTERRUPT_ENABLE                 27
-#define     PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE                26
-#define     PCI_PARITY_ERROR_INTERRUPT_ENABLE                   25
-#define     PCI_INTA_INTERRUPT_ENABLE                           24
-#define     PCI_PME_INTERRUPT_ENABLE                            23
-#define     PCI_SERR_INTERRUPT_ENABLE                           22
-#define     PCI_PERR_INTERRUPT_ENABLE                           21
-#define     PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE          20
-#define     PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE          19
-#define     PCI_RETRY_ABORT_INTERRUPT_ENABLE                    17
-#define     PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE              16
-#define     GPIO_INTERRUPT_ENABLE                               13
-#define     DMA_D_INTERRUPT_ENABLE                              12
-#define     DMA_C_INTERRUPT_ENABLE                              11
-#define     DMA_B_INTERRUPT_ENABLE                              10
-#define     DMA_A_INTERRUPT_ENABLE                              9
-#define     EEPROM_DONE_INTERRUPT_ENABLE                        8
-#define     VBUS_INTERRUPT_ENABLE                               7
-#define     CONTROL_STATUS_INTERRUPT_ENABLE                     6
-#define     ROOT_PORT_RESET_INTERRUPT_ENABLE                    4
-#define     SUSPEND_REQUEST_INTERRUPT_ENABLE                    3
-#define     SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE             2
-#define     RESUME_INTERRUPT_ENABLE                             1
-#define     SOF_INTERRUPT_ENABLE                                0
-	u32		irqstat0;
-#define     INTA_ASSERTED                                       12
-#define     SETUP_PACKET_INTERRUPT                              7
-#define     ENDPOINT_F_INTERRUPT                                6
-#define     ENDPOINT_E_INTERRUPT                                5
-#define     ENDPOINT_D_INTERRUPT                                4
-#define     ENDPOINT_C_INTERRUPT                                3
-#define     ENDPOINT_B_INTERRUPT                                2
-#define     ENDPOINT_A_INTERRUPT                                1
-#define     ENDPOINT_0_INTERRUPT                                0
-	u32		irqstat1;
-#define     POWER_STATE_CHANGE_INTERRUPT                        27
-#define     PCI_ARBITER_TIMEOUT_INTERRUPT                       26
-#define     PCI_PARITY_ERROR_INTERRUPT                          25
-#define     PCI_INTA_INTERRUPT                                  24
-#define     PCI_PME_INTERRUPT                                   23
-#define     PCI_SERR_INTERRUPT                                  22
-#define     PCI_PERR_INTERRUPT                                  21
-#define     PCI_MASTER_ABORT_RECEIVED_INTERRUPT                 20
-#define     PCI_TARGET_ABORT_RECEIVED_INTERRUPT                 19
-#define     PCI_RETRY_ABORT_INTERRUPT                           17
-#define     PCI_MASTER_CYCLE_DONE_INTERRUPT                     16
-#define     SOF_DOWN_INTERRUPT                                  14
-#define     GPIO_INTERRUPT                                      13
-#define     DMA_D_INTERRUPT                                     12
-#define     DMA_C_INTERRUPT                                     11
-#define     DMA_B_INTERRUPT                                     10
-#define     DMA_A_INTERRUPT                                     9
-#define     EEPROM_DONE_INTERRUPT                               8
-#define     VBUS_INTERRUPT                                      7
-#define     CONTROL_STATUS_INTERRUPT                            6
-#define     ROOT_PORT_RESET_INTERRUPT                           4
-#define     SUSPEND_REQUEST_INTERRUPT                           3
-#define     SUSPEND_REQUEST_CHANGE_INTERRUPT                    2
-#define     RESUME_INTERRUPT                                    1
-#define     SOF_INTERRUPT                                       0
-	// offset 0x0030
-	u32		idxaddr;
-	u32		idxdata;
-	u32		fifoctl;
-#define     PCI_BASE2_RANGE                                     16
-#define     IGNORE_FIFO_AVAILABILITY                            3
-#define     PCI_BASE2_SELECT                                    2
-#define     FIFO_CONFIGURATION_SELECT                           0
-	u32		_unused2;
-	// offset 0x0040
-	u32		memaddr;
-#define     START                                               28
-#define     DIRECTION                                           27
-#define     FIFO_DIAGNOSTIC_SELECT                              24
-#define     MEMORY_ADDRESS                                      0
-	u32		memdata0;
-	u32		memdata1;
-	u32		_unused3;
-	// offset 0x0050
-	u32		gpioctl;
-#define     GPIO3_LED_SELECT                                    12
-#define     GPIO3_INTERRUPT_ENABLE                              11
-#define     GPIO2_INTERRUPT_ENABLE                              10
-#define     GPIO1_INTERRUPT_ENABLE                              9
-#define     GPIO0_INTERRUPT_ENABLE                              8
-#define     GPIO3_OUTPUT_ENABLE                                 7
-#define     GPIO2_OUTPUT_ENABLE                                 6
-#define     GPIO1_OUTPUT_ENABLE                                 5
-#define     GPIO0_OUTPUT_ENABLE                                 4
-#define     GPIO3_DATA                                          3
-#define     GPIO2_DATA                                          2
-#define     GPIO1_DATA                                          1
-#define     GPIO0_DATA                                          0
-	u32		gpiostat;
-#define     GPIO3_INTERRUPT                                     3
-#define     GPIO2_INTERRUPT                                     2
-#define     GPIO1_INTERRUPT                                     1
-#define     GPIO0_INTERRUPT                                     0
-} __attribute__ ((packed));
-
-/* usb control, BAR0 + 0x0080 */
-struct net2280_usb_regs {
-	// offset 0x0080
-	u32		stdrsp;
-#define     STALL_UNSUPPORTED_REQUESTS                          31
-#define     SET_TEST_MODE                                       16
-#define     GET_OTHER_SPEED_CONFIGURATION                       15
-#define     GET_DEVICE_QUALIFIER                                14
-#define     SET_ADDRESS                                         13
-#define     ENDPOINT_SET_CLEAR_HALT                             12
-#define     DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP               11
-#define     GET_STRING_DESCRIPTOR_2                             10
-#define     GET_STRING_DESCRIPTOR_1                             9
-#define     GET_STRING_DESCRIPTOR_0                             8
-#define     GET_SET_INTERFACE                                   6
-#define     GET_SET_CONFIGURATION                               5
-#define     GET_CONFIGURATION_DESCRIPTOR                        4
-#define     GET_DEVICE_DESCRIPTOR                               3
-#define     GET_ENDPOINT_STATUS                                 2
-#define     GET_INTERFACE_STATUS                                1
-#define     GET_DEVICE_STATUS                                   0
-	u32		prodvendid;
-#define     PRODUCT_ID                                          16
-#define     VENDOR_ID                                           0
-	u32		relnum;
-	u32		usbctl;
-#define     SERIAL_NUMBER_INDEX                                 16
-#define     PRODUCT_ID_STRING_ENABLE                            13
-#define     VENDOR_ID_STRING_ENABLE                             12
-#define     USB_ROOT_PORT_WAKEUP_ENABLE                         11
-#define     VBUS_PIN                                            10
-#define     TIMED_DISCONNECT                                    9
-#define     SUSPEND_IMMEDIATELY                                 7
-#define     SELF_POWERED_USB_DEVICE                             6
-#define     REMOTE_WAKEUP_SUPPORT                               5
-#define     PME_POLARITY                                        4
-#define     USB_DETECT_ENABLE                                   3
-#define     PME_WAKEUP_ENABLE                                   2
-#define     DEVICE_REMOTE_WAKEUP_ENABLE                         1
-#define     SELF_POWERED_STATUS                                 0
-	// offset 0x0090
-	u32		usbstat;
-#define     HIGH_SPEED                                          7
-#define     FULL_SPEED                                          6
-#define     GENERATE_RESUME                                     5
-#define     GENERATE_DEVICE_REMOTE_WAKEUP                       4
-	u32		xcvrdiag;
-#define     FORCE_HIGH_SPEED_MODE                               31
-#define     FORCE_FULL_SPEED_MODE                               30
-#define     USB_TEST_MODE                                       24
-#define     LINE_STATE                                          16
-#define     TRANSCEIVER_OPERATION_MODE                          2
-#define     TRANSCEIVER_SELECT                                  1
-#define     TERMINATION_SELECT                                  0
-	u32		setup0123;
-	u32		setup4567;
-	// offset 0x0090
-	u32		_unused0;
-	u32		ouraddr;
-#define     FORCE_IMMEDIATE                                     7
-#define     OUR_USB_ADDRESS                                     0
-	u32		ourconfig;
-} __attribute__ ((packed));
-
-/* pci control, BAR0 + 0x0100 */
-struct net2280_pci_regs {
-	// offset 0x0100
-	u32		 pcimstctl;
-#define     PCI_ARBITER_PARK_SELECT                             13
-#define     PCI_MULTI LEVEL_ARBITER                             12
-#define     PCI_RETRY_ABORT_ENABLE                              11
-#define     DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE              10
-#define     DMA_READ_MULTIPLE_ENABLE                            9
-#define     DMA_READ_LINE_ENABLE                                8
-#define     PCI_MASTER_COMMAND_SELECT                           6
-#define         MEM_READ_OR_WRITE                                   0
-#define         IO_READ_OR_WRITE                                    1
-#define         CFG_READ_OR_WRITE                                   2
-#define     PCI_MASTER_START                                    5
-#define     PCI_MASTER_READ_WRITE                               4
-#define         PCI_MASTER_WRITE                                    0
-#define         PCI_MASTER_READ                                     1
-#define     PCI_MASTER_BYTE_WRITE_ENABLES                       0
-	u32		 pcimstaddr;
-	u32		 pcimstdata;
-	u32		 pcimststat;
-#define     PCI_ARBITER_CLEAR                                   2
-#define     PCI_EXTERNAL_ARBITER                                1
-#define     PCI_HOST_MODE                                       0
-} __attribute__ ((packed));
-
-/* dma control, BAR0 + 0x0180 ... array of four structs like this,
- * for channels 0..3.  see also struct net2280_dma:  descriptor
- * that can be loaded into some of these registers.
- */
-struct net2280_dma_regs {	/* [11.7] */
-	// offset 0x0180, 0x01a0, 0x01c0, 0x01e0, 
-	u32		dmactl;
-#define     DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE            25
-#define     DMA_CLEAR_COUNT_ENABLE                              21
-#define     DESCRIPTOR_POLLING_RATE                             19
-#define         POLL_CONTINUOUS                                     0
-#define         POLL_1_USEC                                         1
-#define         POLL_100_USEC                                       2
-#define         POLL_1_MSEC                                         3
-#define     DMA_VALID_BIT_POLLING_ENABLE                        18
-#define     DMA_VALID_BIT_ENABLE                                17
-#define     DMA_SCATTER_GATHER_ENABLE                           16
-#define     DMA_OUT_AUTO_START_ENABLE                           4
-#define     DMA_PREEMPT_ENABLE                                  3
-#define     DMA_FIFO_VALIDATE                                   2
-#define     DMA_ENABLE                                          1
-#define     DMA_ADDRESS_HOLD                                    0
-	u32		dmastat;
-#define     DMA_ABORT_DONE_INTERRUPT                            27
-#define     DMA_SCATTER_GATHER_DONE_INTERRUPT                   25
-#define     DMA_TRANSACTION_DONE_INTERRUPT                      24
-#define     DMA_ABORT                                           1
-#define     DMA_START                                           0
-	u32		_unused0 [2];
-	// offset 0x0190, 0x01b0, 0x01d0, 0x01f0, 
-	u32		dmacount;
-#define     VALID_BIT                                           31
-#define     DMA_DIRECTION                                       30
-#define     DMA_DONE_INTERRUPT_ENABLE                           29
-#define     END_OF_CHAIN                                        28
-#define         DMA_BYTE_COUNT_MASK                                 ((1<<24)-1)
-#define     DMA_BYTE_COUNT                                      0
-	u32		dmaaddr;
-	u32		dmadesc;
-	u32		_unused1;
-} __attribute__ ((packed));
-
-/* dedicated endpoint registers, BAR0 + 0x0200 */
-
-struct net2280_dep_regs {	/* [11.8] */
-	// offset 0x0200, 0x0210, 0x220, 0x230, 0x240
-	u32		dep_cfg;
-	// offset 0x0204, 0x0214, 0x224, 0x234, 0x244
-	u32		dep_rsp;
-	u32		_unused [2];
-} __attribute__ ((packed));
-
-/* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs
- * like this, for ep0 then the configurable endpoints A..F
- * ep0 reserved for control; E and F have only 64 bytes of fifo
- */
-struct net2280_ep_regs {	/* [11.9] */
-	// offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0
-	u32		ep_cfg;
-#define     ENDPOINT_BYTE_COUNT                                 16
-#define     ENDPOINT_ENABLE                                     10
-#define     ENDPOINT_TYPE                                       8
-#define     ENDPOINT_DIRECTION                                  7
-#define     ENDPOINT_NUMBER                                     0
-	u32		ep_rsp;
-#define     SET_NAK_OUT_PACKETS                                 15
-#define     SET_EP_HIDE_STATUS_PHASE                            14
-#define     SET_EP_FORCE_CRC_ERROR                              13
-#define     SET_INTERRUPT_MODE                                  12
-#define     SET_CONTROL_STATUS_PHASE_HANDSHAKE                  11
-#define     SET_NAK_OUT_PACKETS_MODE                            10
-#define     SET_ENDPOINT_TOGGLE                                 9
-#define     SET_ENDPOINT_HALT                                   8
-#define     CLEAR_NAK_OUT_PACKETS                               7
-#define     CLEAR_EP_HIDE_STATUS_PHASE                          6
-#define     CLEAR_EP_FORCE_CRC_ERROR                            5
-#define     CLEAR_INTERRUPT_MODE                                4
-#define     CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE                3
-#define     CLEAR_NAK_OUT_PACKETS_MODE                          2
-#define     CLEAR_ENDPOINT_TOGGLE                               1
-#define     CLEAR_ENDPOINT_HALT                                 0
-	u32		ep_irqenb;
-#define     SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE              6
-#define     SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE           5
-#define     DATA_PACKET_RECEIVED_INTERRUPT_ENABLE               3
-#define     DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE            2
-#define     DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE                1
-#define     DATA_IN_TOKEN_INTERRUPT_ENABLE                      0
-	u32		ep_stat;
-#define     FIFO_VALID_COUNT                                    24
-#define     HIGH_BANDWIDTH_OUT_TRANSACTION_PID                  22
-#define     TIMEOUT                                             21
-#define     USB_STALL_SENT                                      20
-#define     USB_IN_NAK_SENT                                     19
-#define     USB_IN_ACK_RCVD                                     18
-#define     USB_OUT_PING_NAK_SENT                               17
-#define     USB_OUT_ACK_SENT                                    16
-#define     FIFO_OVERFLOW                                       13
-#define     FIFO_UNDERFLOW                                      12
-#define     FIFO_FULL                                           11
-#define     FIFO_EMPTY                                          10
-#define     FIFO_FLUSH                                          9
-#define     SHORT_PACKET_OUT_DONE_INTERRUPT                     6
-#define     SHORT_PACKET_TRANSFERRED_INTERRUPT                  5
-#define     NAK_OUT_PACKETS                                     4
-#define     DATA_PACKET_RECEIVED_INTERRUPT                      3
-#define     DATA_PACKET_TRANSMITTED_INTERRUPT                   2
-#define     DATA_OUT_PING_TOKEN_INTERRUPT                       1
-#define     DATA_IN_TOKEN_INTERRUPT                             0
-	// offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0
-	u32		ep_avail;
-	u32		ep_data;
-	u32		_unused0 [2];
-} __attribute__ ((packed));
+#include <linux/usb/net2280.h>
 
 /*-------------------------------------------------------------------------*/