summaryrefslogtreecommitdiffstats
path: root/drivers/tty
diff options
context:
space:
mode:
authorStefan Agner <stefan@agner.ch>2018-04-19 17:39:16 +0200
committerGreg Kroah-Hartman <gregkh@linuxfoundation.org>2018-04-23 09:53:36 +0200
commit6d215f83e5fccb3dd023e97fef1bd0029bfedde9 (patch)
tree601f424331f62f7ebad83ac850477845a055e781 /drivers/tty
parent46c6975a1fd9794ed979565235d24b2f5004e014 (diff)
downloadlinux-6d215f83e5fccb3dd023e97fef1bd0029bfedde9.tar.bz2
serial: imx: warn user when using unsupported configuration
When using half-duplex mode (which disables receiver during txing) the RTS signal cannot be driven low during transmission when using i.MX UART RTS/CTS control. This seems to be a limitation of the i.MX UART IP: The RTS (CTS_B) signal is controlled by the receiver. When the receiver is disabled, the signal stays in UART logic idle state which is high... If SER_RS485_RTS_ON_SEND is used, RTS needs to be high active during transmission. Since this is the default state of the RTS (CTS_B) signal when the receiver is off, half-duplex mode in this configuration works fine. However, a low-active RTS signal (flag SER_RS485_RTS_ON_SEND not set) cannot be generated when the receiver is turned off. Print an error if the user selects this unsupported configuration (both SER_RS485_RTS_ON_SEND and SER_RS485_RX_DURING_TX unset) and configure the closest working configuration (set the SER_RS485_RX_DURING_TX flag). Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diffstat (limited to 'drivers/tty')
-rw-r--r--drivers/tty/serial/imx.c17
1 files changed, 17 insertions, 0 deletions
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 91f3a1a5cb7f..65d7a2bfb6d2 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -1833,6 +1833,11 @@ static int imx_uart_rs485_config(struct uart_port *port,
rs485conf->flags &= ~SER_RS485_ENABLED;
if (rs485conf->flags & SER_RS485_ENABLED) {
+ /* Enable receiver if low-active RTS signal is requested */
+ if (sport->have_rtscts && !sport->have_rtsgpio &&
+ !(rs485conf->flags & SER_RS485_RTS_ON_SEND))
+ rs485conf->flags |= SER_RS485_RX_DURING_TX;
+
/* disable transmitter */
ucr2 = imx_uart_readl(sport, UCR2);
if (rs485conf->flags & SER_RS485_RTS_AFTER_SEND)
@@ -2265,6 +2270,18 @@ static int imx_uart_probe(struct platform_device *pdev)
(!sport->have_rtscts && !sport->have_rtsgpio))
dev_err(&pdev->dev, "no RTS control, disabling rs485\n");
+ /*
+ * If using the i.MX UART RTS/CTS control then the RTS (CTS_B)
+ * signal cannot be set low during transmission in case the
+ * receiver is off (limitation of the i.MX UART IP).
+ */
+ if (sport->port.rs485.flags & SER_RS485_ENABLED &&
+ sport->have_rtscts && !sport->have_rtsgpio &&
+ (!(sport->port.rs485.flags & SER_RS485_RTS_ON_SEND) &&
+ !(sport->port.rs485.flags & SER_RS485_RX_DURING_TX)))
+ dev_err(&pdev->dev,
+ "low-active RTS not possible when receiver is off, enabling receiver\n");
+
imx_uart_rs485_config(&sport->port, &sport->port.rs485);
/* Disable interrupts before requesting them */