Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus

Pull MIPS updates from Ralf Baechle:
 "MIPS updates:

   - All the things that didn't make 3.10.
   - Removes the Windriver PPMC platform.  Nobody will miss it.
   - Remove a workaround from kernel/irq/irqdomain.c which was there
     exclusivly for MIPS.  Patch by Grant Likely.
   - More small improvments for the SEAD 3 platform
   - Improvments on the BMIPS / SMP support for the BCM63xx series.
   - Various cleanups of dead leftovers.
   - Platform support for the Cavium Octeon-based EdgeRouter Lite.

  Two large KVM patchsets didn't make it for this pull request because
  their respective authors are vacationing"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
  MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
  MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
  MIPS: SEAD3: Disable L2 cache on SEAD-3.
  MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
  MIPS: BCM63xx: Add SMP support to prom.c
  MIPS: define write{b,w,l,q}_relaxed
  MIPS: Expose missing pci_io{map,unmap} declarations
  MIPS: Malta: Update GCMP detection.
  Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
  MIPS: APSP: Remove <asm/kspd.h>
  SSB: Kconfig: Amend SSB_EMBEDDED dependencies
  MIPS: microMIPS: Fix improper definition of ISA exception bit.
  MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
  MIPS: Declare emulate_load_store_microMIPS as a static function.
  MIPS: Fix typos and cleanup comment
  MIPS: Cleanup indentation and whitespace
  MIPS: BMIPS: support booting from physical CPU other than 0
  MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
  MIPS: GIC: Fix gic_set_affinity infinite loop
  MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
  ...

1 files changed, 69 insertions, 39 deletions

diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index d07b6af3a937..76a8daadff47 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -29,6 +29,8 @@
 #include <linux/clk.h>
 #include <linux/pm_runtime.h>
 
+#include <asm/byteorder.h>
+
 #include "8250.h"
 
 /* Offsets for the DesignWare specific registers */
@@ -57,6 +59,7 @@ struct dw8250_data {
 	int		last_lcr;
 	int		line;
 	struct clk	*clk;
+	u8		usr_reg;
 };
 
 static void dw8250_serial_out(struct uart_port *p, int offset, int value)
@@ -77,6 +80,13 @@ static unsigned int dw8250_serial_in(struct uart_port *p, int offset)
 	return readb(p->membase + offset);
 }
 
+/* Read Back (rb) version to ensure register access ording. */
+static void dw8250_serial_out_rb(struct uart_port *p, int offset, int value)
+{
+	dw8250_serial_out(p, offset, value);
+	dw8250_serial_in(p, UART_LCR);
+}
+
 static void dw8250_serial_out32(struct uart_port *p, int offset, int value)
 {
 	struct dw8250_data *d = p->private_data;
@@ -104,7 +114,7 @@ static int dw8250_handle_irq(struct uart_port *p)
 		return 1;
 	} else if ((iir & UART_IIR_BUSY) == UART_IIR_BUSY) {
 		/* Clear the USR and write the LCR again. */
-		(void)p->serial_in(p, DW_UART_USR);
+		(void)p->serial_in(p, d->usr_reg);
 		p->serial_out(p, UART_LCR, d->last_lcr);
 
 		return 1;
@@ -125,12 +135,60 @@ dw8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
 		pm_runtime_put_sync_suspend(port->dev);
 }
 
-static int dw8250_probe_of(struct uart_port *p)
+static void dw8250_setup_port(struct uart_8250_port *up)
+{
+	struct uart_port	*p = &up->port;
+	u32			reg = readl(p->membase + DW_UART_UCV);
+
+	/*
+	 * If the Component Version Register returns zero, we know that
+	 * ADDITIONAL_FEATURES are not enabled. No need to go any further.
+	 */
+	if (!reg)
+		return;
+
+	dev_dbg_ratelimited(p->dev, "Designware UART version %c.%c%c\n",
+		(reg >> 24) & 0xff, (reg >> 16) & 0xff, (reg >> 8) & 0xff);
+
+	reg = readl(p->membase + DW_UART_CPR);
+	if (!reg)
+		return;
+
+	/* Select the type based on fifo */
+	if (reg & DW_UART_CPR_FIFO_MODE) {
+		p->type = PORT_16550A;
+		p->flags |= UPF_FIXED_TYPE;
+		p->fifosize = DW_UART_CPR_FIFO_SIZE(reg);
+		up->tx_loadsz = p->fifosize;
+		up->capabilities = UART_CAP_FIFO;
+	}
+
+	if (reg & DW_UART_CPR_AFCE_MODE)
+		up->capabilities |= UART_CAP_AFE;
+}
+
+static int dw8250_probe_of(struct uart_port *p,
+			   struct dw8250_data *data)
 {
 	struct device_node	*np = p->dev->of_node;
 	u32			val;
-
-	if (!of_property_read_u32(np, "reg-io-width", &val)) {
+	bool has_ucv = true;
+
+	if (of_device_is_compatible(np, "cavium,octeon-3860-uart")) {
+#ifdef __BIG_ENDIAN
+		/*
+		 * Low order bits of these 64-bit registers, when
+		 * accessed as a byte, are 7 bytes further down in the
+		 * address space in big endian mode.
+		 */
+		p->membase += 7;
+#endif
+		p->serial_out = dw8250_serial_out_rb;
+		p->flags = ASYNC_SKIP_TEST | UPF_SHARE_IRQ | UPF_FIXED_TYPE;
+		p->type = PORT_OCTEON;
+		data->usr_reg = 0x27;
+		has_ucv = false;
+	} else if (!of_property_read_u32(np, "reg-io-width", &val)) {
 		switch (val) {
 		case 1:
 			break;
@@ -144,6 +202,8 @@ static int dw8250_probe_of(struct uart_port *p)
 			return -EINVAL;
 		}
 	}
+	if (has_ucv)
+		dw8250_setup_port(container_of(p, struct uart_8250_port, port));
 
 	if (!of_property_read_u32(np, "reg-shift", &val))
 		p->regshift = val;
@@ -168,6 +228,8 @@ static int dw8250_probe_acpi(struct uart_8250_port *up)
 	const struct acpi_device_id *id;
 	struct uart_port *p = &up->port;
 
+	dw8250_setup_port(up);
+
 	id = acpi_match_device(p->dev->driver->acpi_match_table, p->dev);
 	if (!id)
 		return -ENODEV;
@@ -196,38 +258,6 @@ static inline int dw8250_probe_acpi(struct uart_8250_port *up)
 }
 #endif /* CONFIG_ACPI */
 
-static void dw8250_setup_port(struct uart_8250_port *up)
-{
-	struct uart_port	*p = &up->port;
-	u32			reg = readl(p->membase + DW_UART_UCV);
-
-	/*
-	 * If the Component Version Register returns zero, we know that
-	 * ADDITIONAL_FEATURES are not enabled. No need to go any further.
-	 */
-	if (!reg)
-		return;
-
-	dev_dbg_ratelimited(p->dev, "Designware UART version %c.%c%c\n",
-		(reg >> 24) & 0xff, (reg >> 16) & 0xff, (reg >> 8) & 0xff);
-
-	reg = readl(p->membase + DW_UART_CPR);
-	if (!reg)
-		return;
-
-	/* Select the type based on fifo */
-	if (reg & DW_UART_CPR_FIFO_MODE) {
-		p->type = PORT_16550A;
-		p->flags |= UPF_FIXED_TYPE;
-		p->fifosize = DW_UART_CPR_FIFO_SIZE(reg);
-		up->tx_loadsz = p->fifosize;
-		up->capabilities = UART_CAP_FIFO;
-	}
-
-	if (reg & DW_UART_CPR_AFCE_MODE)
-		up->capabilities |= UART_CAP_AFE;
-}
-
 static int dw8250_probe(struct platform_device *pdev)
 {
 	struct uart_8250_port uart = {};
@@ -259,6 +289,7 @@ static int dw8250_probe(struct platform_device *pdev)
 	if (!data)
 		return -ENOMEM;
 
+	data->usr_reg = DW_UART_USR;
 	data->clk = devm_clk_get(&pdev->dev, NULL);
 	if (!IS_ERR(data->clk)) {
 		clk_prepare_enable(data->clk);
@@ -270,10 +301,8 @@ static int dw8250_probe(struct platform_device *pdev)
 	uart.port.serial_out = dw8250_serial_out;
 	uart.port.private_data = data;
 
-	dw8250_setup_port(&uart);
-
 	if (pdev->dev.of_node) {
-		err = dw8250_probe_of(&uart.port);
+		err = dw8250_probe_of(&uart.port, data);
 		if (err)
 			return err;
 	} else if (ACPI_HANDLE(&pdev->dev)) {
@@ -362,6 +391,7 @@ static const struct dev_pm_ops dw8250_pm_ops = {
 
 static const struct of_device_id dw8250_of_match[] = {
 	{ .compatible = "snps,dw-apb-uart" },
+	{ .compatible = "cavium,octeon-3860-uart" },
 	{ /* Sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, dw8250_of_match);