[SCSI] lpfc 8.3.36: Fixed boot from san failure

Fixed boot from san failure when SLI4 FC device presented on the same PCI bus

The request_firmware interface can induce delays while looking
for firmware files, even if no fw file is present. In some situations
the delays exceeded scan_wait timeouts, resulting in situations in which
the boot device had not been discovered in time.  Boot Device does not
need to be on a lpfc device.

Change request_firmware use to be module paramater driven. Default is to
not attempt firmware download on boot. Add sysfs parameter to invoke
firmware update.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

1 files changed, 42 insertions, 13 deletions

diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c
index 7dc4218d9c4c..d89569307416 100644
--- a/drivers/scsi/lpfc/lpfc_init.c
+++ b/drivers/scsi/lpfc/lpfc_init.c
@@ -9450,7 +9450,7 @@ lpfc_write_firmware(const struct firmware *fw, void *context)
 	struct lpfc_dmabuf *dmabuf, *next;
 	uint32_t offset = 0, temp_offset = 0;
 
-	/* It can be null, sanity check */
+	/* It can be null in no-wait mode, sanity check */
 	if (!fw) {
 		rc = -ENXIO;
 		goto out;
@@ -9528,11 +9528,48 @@ release_out:
 	release_firmware(fw);
 out:
 	lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
-			"3024 Firmware update done: %d.", rc);
+			"3024 Firmware update done: %d.\n", rc);
 	return;
 }
 
 /**
+ * lpfc_sli4_request_firmware_update - Request linux generic firmware upgrade
+ * @phba: pointer to lpfc hba data structure.
+ *
+ * This routine is called to perform Linux generic firmware upgrade on device
+ * that supports such feature.
+ **/
+int
+lpfc_sli4_request_firmware_update(struct lpfc_hba *phba, uint8_t fw_upgrade)
+{
+	uint8_t file_name[ELX_MODEL_NAME_SIZE];
+	int ret;
+	const struct firmware *fw;
+
+	/* Only supported on SLI4 interface type 2 for now */
+	if (bf_get(lpfc_sli_intf_if_type, &phba->sli4_hba.sli_intf) !=
+	    LPFC_SLI_INTF_IF_TYPE_2)
+		return -EPERM;
+
+	snprintf(file_name, ELX_MODEL_NAME_SIZE, "%s.grp", phba->ModelName);
+
+	if (fw_upgrade == INT_FW_UPGRADE) {
+		ret = request_firmware_nowait(THIS_MODULE, FW_ACTION_HOTPLUG,
+					file_name, &phba->pcidev->dev,
+					GFP_KERNEL, (void *)phba,
+					lpfc_write_firmware);
+	} else if (fw_upgrade == RUN_FW_UPGRADE) {
+		ret = request_firmware(&fw, file_name, &phba->pcidev->dev);
+		if (!ret)
+			lpfc_write_firmware(fw, (void *)phba);
+	} else {
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+/**
  * lpfc_pci_probe_one_s4 - PCI probe func to reg SLI-4 device to PCI subsys
  * @pdev: pointer to PCI device
  * @pid: pointer to PCI device identifier
@@ -9560,7 +9597,6 @@ lpfc_pci_probe_one_s4(struct pci_dev *pdev, const struct pci_device_id *pid)
 	uint32_t cfg_mode, intr_mode;
 	int mcnt;
 	int adjusted_fcp_io_channel;
-	uint8_t file_name[ELX_MODEL_NAME_SIZE];
 
 	/* Allocate memory for HBA structure */
 	phba = lpfc_hba_alloc(pdev);
@@ -9703,16 +9739,9 @@ lpfc_pci_probe_one_s4(struct pci_dev *pdev, const struct pci_device_id *pid)
 	/* Perform post initialization setup */
 	lpfc_post_init_setup(phba);
 
-	/* check for firmware upgrade or downgrade (if_type 2 only) */
-	if (bf_get(lpfc_sli_intf_if_type, &phba->sli4_hba.sli_intf) ==
-	    LPFC_SLI_INTF_IF_TYPE_2) {
-		snprintf(file_name, ELX_MODEL_NAME_SIZE, "%s.grp",
-			 phba->ModelName);
-		ret = request_firmware_nowait(THIS_MODULE, FW_ACTION_HOTPLUG,
-					file_name, &phba->pcidev->dev,
-					GFP_KERNEL, (void *)phba,
-					lpfc_write_firmware);
-	}
+	/* check for firmware upgrade or downgrade */
+	if (phba->cfg_request_firmware_upgrade)
+		ret = lpfc_sli4_request_firmware_update(phba, INT_FW_UPGRADE);
 
 	/* Check if there are static vports to be created. */
 	lpfc_create_static_vport(phba);