Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 921 insertions, 0 deletions

diff --git a/drivers/parisc/iosapic.c b/drivers/parisc/iosapic.c
new file mode 100644
index 000000000000..91df0bf181dd
--- /dev/null
+++ b/drivers/parisc/iosapic.c
@@ -0,0 +1,921 @@
+/*
+** I/O Sapic Driver - PCI interrupt line support
+**
+**      (c) Copyright 1999 Grant Grundler
+**      (c) Copyright 1999 Hewlett-Packard Company
+**
+**      This program is free software; you can redistribute it and/or modify
+**      it under the terms of the GNU General Public License as published by
+**      the Free Software Foundation; either version 2 of the License, or
+**      (at your option) any later version.
+**
+** The I/O sapic driver manages the Interrupt Redirection Table which is
+** the control logic to convert PCI line based interrupts into a Message
+** Signaled Interrupt (aka Transaction Based Interrupt, TBI).
+**
+** Acronyms
+** --------
+** HPA  Hard Physical Address (aka MMIO address)
+** IRQ  Interrupt ReQuest. Implies Line based interrupt.
+** IRT	Interrupt Routing Table (provided by PAT firmware)
+** IRdT Interrupt Redirection Table. IRQ line to TXN ADDR/DATA
+**      table which is implemented in I/O SAPIC.
+** ISR  Interrupt Service Routine. aka Interrupt handler.
+** MSI	Message Signaled Interrupt. PCI 2.2 functionality.
+**      aka Transaction Based Interrupt (or TBI).
+** PA   Precision Architecture. HP's RISC architecture.
+** RISC Reduced Instruction Set Computer.
+**
+**
+** What's a Message Signalled Interrupt?
+** -------------------------------------
+** MSI is a write transaction which targets a processor and is similar
+** to a processor write to memory or MMIO. MSIs can be generated by I/O
+** devices as well as processors and require *architecture* to work.
+**
+** PA only supports MSI. So I/O subsystems must either natively generate
+** MSIs (e.g. GSC or HP-PB) or convert line based interrupts into MSIs
+** (e.g. PCI and EISA).  IA64 supports MSIs via a "local SAPIC" which
+** acts on behalf of a processor.
+**
+** MSI allows any I/O device to interrupt any processor. This makes
+** load balancing of the interrupt processing possible on an SMP platform.
+** Interrupts are also ordered WRT to DMA data.  It's possible on I/O
+** coherent systems to completely eliminate PIO reads from the interrupt
+** path. The device and driver must be designed and implemented to
+** guarantee all DMA has been issued (issues about atomicity here)
+** before the MSI is issued. I/O status can then safely be read from
+** DMA'd data by the ISR.
+**
+**
+** PA Firmware
+** -----------
+** PA-RISC platforms have two fundementally different types of firmware.
+** For PCI devices, "Legacy" PDC initializes the "INTERRUPT_LINE" register
+** and BARs similar to a traditional PC BIOS.
+** The newer "PAT" firmware supports PDC calls which return tables.
+** PAT firmware only initializes PCI Console and Boot interface.
+** With these tables, the OS can progam all other PCI devices.
+**
+** One such PAT PDC call returns the "Interrupt Routing Table" (IRT).
+** The IRT maps each PCI slot's INTA-D "output" line to an I/O SAPIC
+** input line.  If the IRT is not available, this driver assumes
+** INTERRUPT_LINE register has been programmed by firmware. The latter
+** case also means online addition of PCI cards can NOT be supported
+** even if HW support is present.
+**
+** All platforms with PAT firmware to date (Oct 1999) use one Interrupt
+** Routing Table for the entire platform.
+**
+** Where's the iosapic?
+** --------------------
+** I/O sapic is part of the "Core Electronics Complex". And on HP platforms
+** it's integrated as part of the PCI bus adapter, "lba".  So no bus walk
+** will discover I/O Sapic. I/O Sapic driver learns about each device
+** when lba driver advertises the presence of the I/O sapic by calling
+** iosapic_register().
+**
+**
+** IRQ handling notes
+** ------------------
+** The IO-SAPIC can indicate to the CPU which interrupt was asserted.
+** So, unlike the GSC-ASIC and Dino, we allocate one CPU interrupt per
+** IO-SAPIC interrupt and call the device driver's handler directly.
+** The IO-SAPIC driver hijacks the CPU interrupt handler so it can
+** issue the End Of Interrupt command to the IO-SAPIC.
+**
+** Overview of exported iosapic functions
+** --------------------------------------
+** (caveat: code isn't finished yet - this is just the plan)
+**
+** iosapic_init:
+**   o initialize globals (lock, etc)
+**   o try to read IRT. Presence of IRT determines if this is
+**     a PAT platform or not.
+**
+** iosapic_register():
+**   o create iosapic_info instance data structure
+**   o allocate vector_info array for this iosapic
+**   o initialize vector_info - read corresponding IRdT?
+**
+** iosapic_xlate_pin: (only called by fixup_irq for PAT platform)
+**   o intr_pin = read cfg (INTERRUPT_PIN);
+**   o if (device under PCI-PCI bridge)
+**               translate slot/pin
+**
+** iosapic_fixup_irq:
+**   o if PAT platform (IRT present)
+**	   intr_pin = iosapic_xlate_pin(isi,pcidev):
+**         intr_line = find IRT entry(isi, PCI_SLOT(pcidev), intr_pin)
+**         save IRT entry into vector_info later
+**         write cfg INTERRUPT_LINE (with intr_line)?
+**     else
+**         intr_line = pcidev->irq
+**         IRT pointer = NULL
+**     endif
+**   o locate vector_info (needs: isi, intr_line)
+**   o allocate processor "irq" and get txn_addr/data
+**   o request_irq(processor_irq,  iosapic_interrupt, vector_info,...)
+**
+** iosapic_enable_irq:
+**   o clear any pending IRQ on that line
+**   o enable IRdT - call enable_irq(vector[line]->processor_irq)
+**   o write EOI in case line is already asserted.
+**
+** iosapic_disable_irq:
+**   o disable IRdT - call disable_irq(vector[line]->processor_irq)
+*/
+
+
+/* FIXME: determine which include files are really needed */
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+
+#include <asm/byteorder.h>	/* get in-line asm for swab */
+#include <asm/pdc.h>
+#include <asm/pdcpat.h>
+#include <asm/page.h>
+#include <asm/system.h>
+#include <asm/io.h>		/* read/write functions */
+#ifdef CONFIG_SUPERIO
+#include <asm/superio.h>
+#endif
+
+#include <asm/iosapic.h>
+#include "./iosapic_private.h"
+
+#define MODULE_NAME "iosapic"
+
+/* "local" compile flags */
+#undef PCI_BRIDGE_FUNCS
+#undef DEBUG_IOSAPIC
+#undef DEBUG_IOSAPIC_IRT
+
+
+#ifdef DEBUG_IOSAPIC
+#define DBG(x...) printk(x)
+#else /* DEBUG_IOSAPIC */
+#define DBG(x...)
+#endif /* DEBUG_IOSAPIC */
+
+#ifdef DEBUG_IOSAPIC_IRT
+#define DBG_IRT(x...) printk(x)
+#else
+#define DBG_IRT(x...)
+#endif
+
+#ifdef CONFIG_64BIT
+#define COMPARE_IRTE_ADDR(irte, hpa)	((irte)->dest_iosapic_addr == (hpa))
+#else
+#define COMPARE_IRTE_ADDR(irte, hpa)	\
+		((irte)->dest_iosapic_addr == ((hpa) | 0xffffffff00000000ULL))
+#endif
+
+#define IOSAPIC_REG_SELECT              0x00
+#define IOSAPIC_REG_WINDOW              0x10
+#define IOSAPIC_REG_EOI                 0x40
+
+#define IOSAPIC_REG_VERSION		0x1
+
+#define IOSAPIC_IRDT_ENTRY(idx)		(0x10+(idx)*2)
+#define IOSAPIC_IRDT_ENTRY_HI(idx)	(0x11+(idx)*2)
+
+static inline unsigned int iosapic_read(void __iomem *iosapic, unsigned int reg)
+{
+	writel(reg, iosapic + IOSAPIC_REG_SELECT);
+	return readl(iosapic + IOSAPIC_REG_WINDOW);
+}
+
+static inline void iosapic_write(void __iomem *iosapic, unsigned int reg, u32 val)
+{
+	writel(reg, iosapic + IOSAPIC_REG_SELECT);
+	writel(val, iosapic + IOSAPIC_REG_WINDOW);
+}
+
+#define IOSAPIC_VERSION_MASK	0x000000ff
+#define	IOSAPIC_VERSION(ver)	((int) (ver & IOSAPIC_VERSION_MASK))
+
+#define IOSAPIC_MAX_ENTRY_MASK          0x00ff0000
+#define IOSAPIC_MAX_ENTRY_SHIFT         0x10
+#define	IOSAPIC_IRDT_MAX_ENTRY(ver)	\
+	(int) (((ver) & IOSAPIC_MAX_ENTRY_MASK) >> IOSAPIC_MAX_ENTRY_SHIFT)
+
+/* bits in the "low" I/O Sapic IRdT entry */
+#define IOSAPIC_IRDT_ENABLE       0x10000
+#define IOSAPIC_IRDT_PO_LOW       0x02000
+#define IOSAPIC_IRDT_LEVEL_TRIG   0x08000
+#define IOSAPIC_IRDT_MODE_LPRI    0x00100
+
+/* bits in the "high" I/O Sapic IRdT entry */
+#define IOSAPIC_IRDT_ID_EID_SHIFT              0x10
+
+
+static spinlock_t iosapic_lock = SPIN_LOCK_UNLOCKED;
+
+static inline void iosapic_eoi(void __iomem *addr, unsigned int data)
+{
+	__raw_writel(data, addr);
+}
+
+/*
+** REVISIT: future platforms may have more than one IRT.
+** If so, the following three fields form a structure which
+** then be linked into a list. Names are chosen to make searching
+** for them easy - not necessarily accurate (eg "cell").
+**
+** Alternative: iosapic_info could point to the IRT it's in.
+** iosapic_register() could search a list of IRT's.
+*/
+static struct irt_entry *irt_cell;
+static size_t irt_num_entry;
+
+static struct irt_entry *iosapic_alloc_irt(int num_entries)
+{
+	unsigned long a;
+
+	/* The IRT needs to be 8-byte aligned for the PDC call. 
+	 * Normally kmalloc would guarantee larger alignment, but
+	 * if CONFIG_DEBUG_SLAB is enabled, then we can get only
+	 * 4-byte alignment on 32-bit kernels
+	 */
+	a = (unsigned long)kmalloc(sizeof(struct irt_entry) * num_entries + 8, GFP_KERNEL);
+	a = (a + 7) & ~7;
+	return (struct irt_entry *)a;
+}
+
+/**
+ * iosapic_load_irt - Fill in the interrupt routing table
+ * @cell_num: The cell number of the CPU we're currently executing on
+ * @irt: The address to place the new IRT at
+ * @return The number of entries found
+ *
+ * The "Get PCI INT Routing Table Size" option returns the number of 
+ * entries in the PCI interrupt routing table for the cell specified 
+ * in the cell_number argument.  The cell number must be for a cell 
+ * within the caller's protection domain.
+ *
+ * The "Get PCI INT Routing Table" option returns, for the cell 
+ * specified in the cell_number argument, the PCI interrupt routing 
+ * table in the caller allocated memory pointed to by mem_addr.
+ * We assume the IRT only contains entries for I/O SAPIC and
+ * calculate the size based on the size of I/O sapic entries.
+ *
+ * The PCI interrupt routing table entry format is derived from the
+ * IA64 SAL Specification 2.4.   The PCI interrupt routing table defines
+ * the routing of PCI interrupt signals between the PCI device output
+ * "pins" and the IO SAPICs' input "lines" (including core I/O PCI
+ * devices).  This table does NOT include information for devices/slots
+ * behind PCI to PCI bridges. See PCI to PCI Bridge Architecture Spec.
+ * for the architected method of routing of IRQ's behind PPB's.
+ */
+
+
+static int __init
+iosapic_load_irt(unsigned long cell_num, struct irt_entry **irt)
+{
+	long status;              /* PDC return value status */
+	struct irt_entry *table;  /* start of interrupt routing tbl */
+	unsigned long num_entries = 0UL;
+
+	BUG_ON(!irt);
+
+	if (is_pdc_pat()) {
+		/* Use pat pdc routine to get interrupt routing table size */
+		DBG("calling get_irt_size (cell %ld)\n", cell_num);
+		status = pdc_pat_get_irt_size(&num_entries, cell_num);
+		DBG("get_irt_size: %ld\n", status);
+
+		BUG_ON(status != PDC_OK);
+		BUG_ON(num_entries == 0);
+
+		/*
+		** allocate memory for interrupt routing table
+		** This interface isn't really right. We are assuming
+		** the contents of the table are exclusively
+		** for I/O sapic devices.
+		*/
+		table = iosapic_alloc_irt(num_entries);
+		if (table == NULL) {
+			printk(KERN_WARNING MODULE_NAME ": read_irt : can "
+					"not alloc mem for IRT\n");
+			return 0;
+		}
+
+		/* get PCI INT routing table */
+		status = pdc_pat_get_irt(table, cell_num);
+		DBG("pdc_pat_get_irt: %ld\n", status);
+		WARN_ON(status != PDC_OK);
+	} else {
+		/*
+		** C3000/J5000 (and similar) platforms with Sprockets PDC
+		** will return exactly one IRT for all iosapics.
+		** So if we have one, don't need to get it again.
+		*/
+		if (irt_cell)
+			return 0;
+
+		/* Should be using the Elroy's HPA, but it's ignored anyway */
+		status = pdc_pci_irt_size(&num_entries, 0);
+		DBG("pdc_pci_irt_size: %ld\n", status);
+
+		if (status != PDC_OK) {
+			/* Not a "legacy" system with I/O SAPIC either */
+			return 0;
+		}
+
+		BUG_ON(num_entries == 0);
+
+		table = iosapic_alloc_irt(num_entries);
+		if (!table) {
+			printk(KERN_WARNING MODULE_NAME ": read_irt : can "
+					"not alloc mem for IRT\n");
+			return 0;
+		}
+
+		/* HPA ignored by this call too. */
+		status = pdc_pci_irt(num_entries, 0, table);
+		BUG_ON(status != PDC_OK);
+	}
+
+	/* return interrupt table address */
+	*irt = table;
+
+#ifdef DEBUG_IOSAPIC_IRT
+{
+	struct irt_entry *p = table;
+	int i;
+
+	printk(MODULE_NAME " Interrupt Routing Table (cell %ld)\n", cell_num);
+	printk(MODULE_NAME " start = 0x%p num_entries %ld entry_size %d\n",
+		table,
+		num_entries,
+		(int) sizeof(struct irt_entry));
+
+	for (i = 0 ; i < num_entries ; i++, p++) {
+		printk(MODULE_NAME " %02x %02x %02x %02x %02x %02x %02x %02x %08x%08x\n",
+		p->entry_type, p->entry_length, p->interrupt_type,
+		p->polarity_trigger, p->src_bus_irq_devno, p->src_bus_id,
+		p->src_seg_id, p->dest_iosapic_intin,
+		((u32 *) p)[2],
+		((u32 *) p)[3]
+		);
+	}
+}
+#endif /* DEBUG_IOSAPIC_IRT */
+
+	return num_entries;
+}
+
+
+
+void __init iosapic_init(void)
+{
+	unsigned long cell = 0;
+
+	DBG("iosapic_init()\n");
+
+#ifdef __LP64__
+	if (is_pdc_pat()) {
+		int status;
+		struct pdc_pat_cell_num cell_info;
+
+		status = pdc_pat_cell_get_number(&cell_info);
+		if (status == PDC_OK) {
+			cell = cell_info.cell_num;
+		}
+	}
+#endif
+
+	/* get interrupt routing table for this cell */
+	irt_num_entry = iosapic_load_irt(cell, &irt_cell);
+	if (irt_num_entry == 0)
+		irt_cell = NULL;	/* old PDC w/o iosapic */
+}
+
+
+/*
+** Return the IRT entry in case we need to look something else up.
+*/
+static struct irt_entry *
+irt_find_irqline(struct iosapic_info *isi, u8 slot, u8 intr_pin)
+{
+	struct irt_entry *i = irt_cell;
+	int cnt;	/* track how many entries we've looked at */
+	u8 irq_devno = (slot << IRT_DEV_SHIFT) | (intr_pin-1);
+
+	DBG_IRT("irt_find_irqline() SLOT %d pin %d\n", slot, intr_pin);
+
+	for (cnt=0; cnt < irt_num_entry; cnt++, i++) {
+
+		/*
+		** Validate: entry_type, entry_length, interrupt_type
+		**
+		** Difference between validate vs compare is the former
+		** should print debug info and is not expected to "fail"
+		** on current platforms.
+		*/
+		if (i->entry_type != IRT_IOSAPIC_TYPE) {
+			DBG_IRT(KERN_WARNING MODULE_NAME ":find_irqline(0x%p): skipping entry %d type %d\n", i, cnt, i->entry_type);
+			continue;
+		}
+		
+		if (i->entry_length != IRT_IOSAPIC_LENGTH) {
+			DBG_IRT(KERN_WARNING MODULE_NAME ":find_irqline(0x%p): skipping entry %d  length %d\n", i, cnt, i->entry_length);
+			continue;
+		}
+
+		if (i->interrupt_type != IRT_VECTORED_INTR) {
+			DBG_IRT(KERN_WARNING MODULE_NAME ":find_irqline(0x%p): skipping entry  %d interrupt_type %d\n", i, cnt, i->interrupt_type);
+			continue;
+		}
+
+		if (!COMPARE_IRTE_ADDR(i, isi->isi_hpa))
+			continue;
+
+		if ((i->src_bus_irq_devno & IRT_IRQ_DEVNO_MASK) != irq_devno)
+			continue;
+
+		/*
+		** Ignore: src_bus_id and rc_seg_id correlate with
+		**         iosapic_info->isi_hpa on HP platforms.
+		**         If needed, pass in "PFA" (aka config space addr)
+		**         instead of slot.
+		*/
+
+		/* Found it! */
+		return i;
+	}
+
+	printk(KERN_WARNING MODULE_NAME ": 0x%lx : no IRT entry for slot %d, pin %d\n",
+			isi->isi_hpa, slot, intr_pin);
+	return NULL;
+}
+
+
+/*
+** xlate_pin() supports the skewing of IRQ lines done by subsidiary bridges.
+** Legacy PDC already does this translation for us and stores it in INTR_LINE.
+**
+** PAT PDC needs to basically do what legacy PDC does:
+** o read PIN
+** o adjust PIN in case device is "behind" a PPB
+**     (eg 4-port 100BT and SCSI/LAN "Combo Card")
+** o convert slot/pin to I/O SAPIC input line.
+**
+** HP platforms only support:
+** o one level of skewing for any number of PPBs
+** o only support PCI-PCI Bridges.
+*/
+static struct irt_entry *
+iosapic_xlate_pin(struct iosapic_info *isi, struct pci_dev *pcidev)
+{
+	u8 intr_pin, intr_slot;
+
+	pci_read_config_byte(pcidev, PCI_INTERRUPT_PIN, &intr_pin);
+
+	DBG_IRT("iosapic_xlate_pin(%s) SLOT %d pin %d\n",
+		pcidev->slot_name, PCI_SLOT(pcidev->devfn), intr_pin);
+
+	if (intr_pin == 0) {
+		/* The device does NOT support/use IRQ lines.  */
+		return NULL;
+	}
+
+	/* Check if pcidev behind a PPB */
+	if (NULL != pcidev->bus->self) {
+		/* Convert pcidev INTR_PIN into something we
+		** can lookup in the IRT.
+		*/
+#ifdef PCI_BRIDGE_FUNCS
+		/*
+		** Proposal #1:
+		**
+		** call implementation specific translation function
+		** This is architecturally "cleaner". HP-UX doesn't
+		** support other secondary bus types (eg. E/ISA) directly.
+		** May be needed for other processor (eg IA64) architectures
+		** or by some ambitous soul who wants to watch TV.
+		*/
+		if (pci_bridge_funcs->xlate_intr_line) {
+			intr_pin = pci_bridge_funcs->xlate_intr_line(pcidev);
+		}
+#else	/* PCI_BRIDGE_FUNCS */
+		struct pci_bus *p = pcidev->bus;
+		/*
+		** Proposal #2:
+		** The "pin" is skewed ((pin + dev - 1) % 4).
+		**
+		** This isn't very clean since I/O SAPIC must assume:
+		**   - all platforms only have PCI busses.
+		**   - only PCI-PCI bridge (eg not PCI-EISA, PCI-PCMCIA)
+		**   - IRQ routing is only skewed once regardless of
+		**     the number of PPB's between iosapic and device.
+		**     (Bit3 expansion chassis follows this rule)
+		**
+		** Advantage is it's really easy to implement.
+		*/
+		intr_pin = ((intr_pin-1)+PCI_SLOT(pcidev->devfn)) % 4;
+		intr_pin++;	/* convert back to INTA-D (1-4) */
+#endif /* PCI_BRIDGE_FUNCS */
+
+		/*
+		** Locate the host slot the PPB nearest the Host bus
+		** adapter.
+		*/
+		while (NULL != p->parent->self)
+			p = p->parent;
+
+		intr_slot = PCI_SLOT(p->self->devfn);
+	} else {
+		intr_slot = PCI_SLOT(pcidev->devfn);
+	}
+	DBG_IRT("iosapic_xlate_pin:  bus %d slot %d pin %d\n",
+				pcidev->bus->secondary, intr_slot, intr_pin);
+
+	return irt_find_irqline(isi, intr_slot, intr_pin);
+}
+
+static void iosapic_rd_irt_entry(struct vector_info *vi , u32 *dp0, u32 *dp1)
+{
+	struct iosapic_info *isp = vi->iosapic;
+	u8 idx = vi->irqline;
+
+	*dp0 = iosapic_read(isp->addr, IOSAPIC_IRDT_ENTRY(idx));
+	*dp1 = iosapic_read(isp->addr, IOSAPIC_IRDT_ENTRY_HI(idx));
+}
+
+
+static void iosapic_wr_irt_entry(struct vector_info *vi, u32 dp0, u32 dp1)
+{
+	struct iosapic_info *isp = vi->iosapic;
+
+	DBG_IRT("iosapic_wr_irt_entry(): irq %d hpa %lx 0x%x 0x%x\n",
+		vi->irqline, isp->isi_hpa, dp0, dp1);
+
+	iosapic_write(isp->addr, IOSAPIC_IRDT_ENTRY(vi->irqline), dp0);
+
+	/* Read the window register to flush the writes down to HW  */
+	dp0 = readl(isp->addr+IOSAPIC_REG_WINDOW);
+
+	iosapic_write(isp->addr, IOSAPIC_IRDT_ENTRY_HI(vi->irqline), dp1);
+
+	/* Read the window register to flush the writes down to HW  */
+	dp1 = readl(isp->addr+IOSAPIC_REG_WINDOW);
+}
+
+/*
+** set_irt prepares the data (dp0, dp1) according to the vector_info
+** and target cpu (id_eid).  dp0/dp1 are then used to program I/O SAPIC
+** IRdT for the given "vector" (aka IRQ line).
+*/
+static void
+iosapic_set_irt_data( struct vector_info *vi, u32 *dp0, u32 *dp1)
+{
+	u32 mode = 0;
+	struct irt_entry *p = vi->irte;
+
+	if ((p->polarity_trigger & IRT_PO_MASK) == IRT_ACTIVE_LO)
+		mode |= IOSAPIC_IRDT_PO_LOW;
+
+	if (((p->polarity_trigger >> IRT_EL_SHIFT) & IRT_EL_MASK) == IRT_LEVEL_TRIG)
+		mode |= IOSAPIC_IRDT_LEVEL_TRIG;
+
+	/*
+	** IA64 REVISIT
+	** PA doesn't support EXTINT or LPRIO bits.
+	*/
+
+	*dp0 = mode | (u32) vi->txn_data;
+
+	/*
+	** Extracting id_eid isn't a real clean way of getting it.
+	** But the encoding is the same for both PA and IA64 platforms.
+	*/
+	if (is_pdc_pat()) {
+		/*
+		** PAT PDC just hands it to us "right".
+		** txn_addr comes from cpu_data[x].txn_addr.
+		*/
+		*dp1 = (u32) (vi->txn_addr);
+	} else {
+		/* 
+		** eg if base_addr == 0xfffa0000),
+		**    we want to get 0xa0ff0000.
+		**
+		** eid	0x0ff00000 -> 0x00ff0000
+		** id	0x000ff000 -> 0xff000000
+		*/
+		*dp1 = (((u32)vi->txn_addr & 0x0ff00000) >> 4) |
+			(((u32)vi->txn_addr & 0x000ff000) << 12);
+	}
+	DBG_IRT("iosapic_set_irt_data(): 0x%x 0x%x\n", *dp0, *dp1);
+}
+
+
+static struct vector_info *iosapic_get_vector(unsigned int irq)
+{
+	return irq_desc[irq].handler_data;
+}
+
+static void iosapic_disable_irq(unsigned int irq)
+{
+	unsigned long flags;
+	struct vector_info *vi = iosapic_get_vector(irq);
+	u32 d0, d1;
+
+	spin_lock_irqsave(&iosapic_lock, flags);
+	iosapic_rd_irt_entry(vi, &d0, &d1);
+	d0 |= IOSAPIC_IRDT_ENABLE;
+	iosapic_wr_irt_entry(vi, d0, d1);
+	spin_unlock_irqrestore(&iosapic_lock, flags);
+}
+
+static void iosapic_enable_irq(unsigned int irq)
+{
+	struct vector_info *vi = iosapic_get_vector(irq);
+	u32 d0, d1;
+
+	/* data is initialized by fixup_irq */
+	WARN_ON(vi->txn_irq  == 0);
+
+	iosapic_set_irt_data(vi, &d0, &d1);
+	iosapic_wr_irt_entry(vi, d0, d1);
+
+#ifdef DEBUG_IOSAPIC_IRT
+{
+	u32 *t = (u32 *) ((ulong) vi->eoi_addr & ~0xffUL);
+	printk("iosapic_enable_irq(): regs %p", vi->eoi_addr);
+	for ( ; t < vi->eoi_addr; t++)
+		printk(" %x", readl(t));
+	printk("\n");
+}
+
+printk("iosapic_enable_irq(): sel ");
+{
+	struct iosapic_info *isp = vi->iosapic;
+
+	for (d0=0x10; d0<0x1e; d0++) {
+		d1 = iosapic_read(isp->addr, d0);
+		printk(" %x", d1);
+	}
+}
+printk("\n");
+#endif
+
+	/*
+	 * Issuing I/O SAPIC an EOI causes an interrupt IFF IRQ line is
+	 * asserted.  IRQ generally should not be asserted when a driver
+	 * enables their IRQ. It can lead to "interesting" race conditions
+	 * in the driver initialization sequence.
+	 */
+	DBG(KERN_DEBUG "enable_irq(%d): eoi(%p, 0x%x)\n", irq,
+			vi->eoi_addr, vi->eoi_data);
+	iosapic_eoi(vi->eoi_addr, vi->eoi_data);
+}
+
+/*
+ * PARISC only supports PCI devices below I/O SAPIC.
+ * PCI only supports level triggered in order to share IRQ lines.
+ * ergo I/O SAPIC must always issue EOI on parisc.
+ *
+ * i386/ia64 support ISA devices and have to deal with
+ * edge-triggered interrupts too.
+ */
+static void iosapic_end_irq(unsigned int irq)
+{
+	struct vector_info *vi = iosapic_get_vector(irq);
+	DBG(KERN_DEBUG "end_irq(%d): eoi(%p, 0x%x)\n", irq,
+			vi->eoi_addr, vi->eoi_data);
+	iosapic_eoi(vi->eoi_addr, vi->eoi_data);
+}
+
+static unsigned int iosapic_startup_irq(unsigned int irq)
+{
+	iosapic_enable_irq(irq);
+	return 0;
+}
+
+static struct hw_interrupt_type iosapic_interrupt_type = {
+	.typename =	"IO-SAPIC-level",
+	.startup =	iosapic_startup_irq,
+	.shutdown =	iosapic_disable_irq,
+	.enable =	iosapic_enable_irq,
+	.disable =	iosapic_disable_irq,
+	.ack =		no_ack_irq,
+	.end =		iosapic_end_irq,
+//	.set_affinity =	iosapic_set_affinity_irq,
+};
+
+int iosapic_fixup_irq(void *isi_obj, struct pci_dev *pcidev)
+{
+	struct iosapic_info *isi = isi_obj;
+	struct irt_entry *irte = NULL;  /* only used if PAT PDC */
+	struct vector_info *vi;
+	int isi_line;	/* line used by device */
+
+	if (!isi) {
+		printk(KERN_WARNING MODULE_NAME ": hpa not registered for %s\n",
+			pci_name(pcidev));
+		return -1;
+	}
+
+#ifdef CONFIG_SUPERIO
+	/*
+	 * HACK ALERT! (non-compliant PCI device support)
+	 *
+	 * All SuckyIO interrupts are routed through the PIC's on function 1.
+	 * But SuckyIO OHCI USB controller gets an IRT entry anyway because
+	 * it advertises INT D for INT_PIN.  Use that IRT entry to get the
+	 * SuckyIO interrupt routing for PICs on function 1 (*BLEECCHH*).
+	 */
+	if (is_superio_device(pcidev)) {
+		/* We must call superio_fixup_irq() to register the pdev */
+		pcidev->irq = superio_fixup_irq(pcidev);
+
+		/* Don't return if need to program the IOSAPIC's IRT... */
+		if (PCI_FUNC(pcidev->devfn) != SUPERIO_USB_FN)
+			return pcidev->irq;
+	}
+#endif /* CONFIG_SUPERIO */
+
+	/* lookup IRT entry for isi/slot/pin set */
+	irte = iosapic_xlate_pin(isi, pcidev);
+	if (!irte) {
+		printk("iosapic: no IRTE for %s (IRQ not connected?)\n",
+				pci_name(pcidev));
+		return -1;
+	}
+	DBG_IRT("iosapic_fixup_irq(): irte %p %x %x %x %x %x %x %x %x\n",
+		irte,
+		irte->entry_type,
+		irte->entry_length,
+		irte->polarity_trigger,
+		irte->src_bus_irq_devno,
+		irte->src_bus_id,
+		irte->src_seg_id,
+		irte->dest_iosapic_intin,
+		(u32) irte->dest_iosapic_addr);
+	isi_line = irte->dest_iosapic_intin;
+
+	/* get vector info for this input line */
+	vi = isi->isi_vector + isi_line;
+	DBG_IRT("iosapic_fixup_irq:  line %d vi 0x%p\n", isi_line, vi);
+
+	/* If this IRQ line has already been setup, skip it */
+	if (vi->irte)
+		goto out;
+
+	vi->irte = irte;
+
+	/*
+	 * Allocate processor IRQ
+	 *
+	 * XXX/FIXME The txn_alloc_irq() code and related code should be
+	 * moved to enable_irq(). That way we only allocate processor IRQ
+	 * bits for devices that actually have drivers claiming them.
+	 * Right now we assign an IRQ to every PCI device present,
+	 * regardless of whether it's used or not.
+	 */
+	vi->txn_irq = txn_alloc_irq(8);
+
+	if (vi->txn_irq < 0)
+		panic("I/O sapic: couldn't get TXN IRQ\n");
+
+	/* enable_irq() will use txn_* to program IRdT */
+	vi->txn_addr = txn_alloc_addr(vi->txn_irq);
+	vi->txn_data = txn_alloc_data(vi->txn_irq);
+
+	vi->eoi_addr = isi->addr + IOSAPIC_REG_EOI;
+	vi->eoi_data = cpu_to_le32(vi->txn_data);
+
+	cpu_claim_irq(vi->txn_irq, &iosapic_interrupt_type, vi);
+
+ out:
+	pcidev->irq = vi->txn_irq;
+
+	DBG_IRT("iosapic_fixup_irq() %d:%d %x %x line %d irq %d\n",
+		PCI_SLOT(pcidev->devfn), PCI_FUNC(pcidev->devfn),
+		pcidev->vendor, pcidev->device, isi_line, pcidev->irq);
+
+	return pcidev->irq;
+}
+
+
+/*
+** squirrel away the I/O Sapic Version
+*/
+static unsigned int
+iosapic_rd_version(struct iosapic_info *isi)
+{
+	return iosapic_read(isi->addr, IOSAPIC_REG_VERSION);
+}
+
+
+/*
+** iosapic_register() is called by "drivers" with an integrated I/O SAPIC.
+** Caller must be certain they have an I/O SAPIC and know its MMIO address.
+**
+**	o allocate iosapic_info and add it to the list
+**	o read iosapic version and squirrel that away
+**	o read size of IRdT.
+**	o allocate and initialize isi_vector[]
+**	o allocate irq region
+*/
+void *iosapic_register(unsigned long hpa)
+{
+	struct iosapic_info *isi = NULL;
+	struct irt_entry *irte = irt_cell;
+	struct vector_info *vip;
+	int cnt;	/* track how many entries we've looked at */
+
+	/*
+	 * Astro based platforms can only support PCI OLARD if they implement
+	 * PAT PDC.  Legacy PDC omits LBAs with no PCI devices from the IRT.
+	 * Search the IRT and ignore iosapic's which aren't in the IRT.
+	 */
+	for (cnt=0; cnt < irt_num_entry; cnt++, irte++) {
+		WARN_ON(IRT_IOSAPIC_TYPE != irte->entry_type);
+		if (COMPARE_IRTE_ADDR(irte, hpa))
+			break;
+	}
+
+	if (cnt >= irt_num_entry) {
+		DBG("iosapic_register() ignoring 0x%lx (NOT FOUND)\n", hpa);
+		return NULL;
+	}
+
+	isi = (struct iosapic_info *)kmalloc(sizeof(struct iosapic_info), GFP_KERNEL);
+	if (!isi) {
+		BUG();
+		return NULL;
+	}
+
+	memset(isi, 0, sizeof(struct iosapic_info));
+
+	isi->addr = ioremap(hpa, 4096);
+	isi->isi_hpa = hpa;
+	isi->isi_version = iosapic_rd_version(isi);
+	isi->isi_num_vectors = IOSAPIC_IRDT_MAX_ENTRY(isi->isi_version) + 1;
+
+	vip = isi->isi_vector = (struct vector_info *)
+		kmalloc(sizeof(struct vector_info) * isi->isi_num_vectors, GFP_KERNEL);
+	if (vip == NULL) {
+		kfree(isi);
+		return NULL;
+	}
+
+	memset(vip, 0, sizeof(struct vector_info) * isi->isi_num_vectors);
+
+	for (cnt=0; cnt < isi->isi_num_vectors; cnt++, vip++) {
+		vip->irqline = (unsigned char) cnt;
+		vip->iosapic = isi;
+	}
+	return isi;
+}
+
+
+#ifdef DEBUG_IOSAPIC
+
+static void
+iosapic_prt_irt(void *irt, long num_entry)
+{
+	unsigned int i, *irp = (unsigned int *) irt;
+
+
+	printk(KERN_DEBUG MODULE_NAME ": Interrupt Routing Table (%lx entries)\n", num_entry);
+
+	for (i=0; i<num_entry; i++, irp += 4) {
+		printk(KERN_DEBUG "%p : %2d %.8x %.8x %.8x %.8x\n",
+					irp, i, irp[0], irp[1], irp[2], irp[3]);
+	}
+}
+
+
+static void
+iosapic_prt_vi(struct vector_info *vi)
+{
+	printk(KERN_DEBUG MODULE_NAME ": vector_info[%d] is at %p\n", vi->irqline, vi);
+	printk(KERN_DEBUG "\t\tstatus:	 %.4x\n", vi->status);
+	printk(KERN_DEBUG "\t\ttxn_irq:  %d\n",  vi->txn_irq);
+	printk(KERN_DEBUG "\t\ttxn_addr: %lx\n", vi->txn_addr);
+	printk(KERN_DEBUG "\t\ttxn_data: %lx\n", vi->txn_data);
+	printk(KERN_DEBUG "\t\teoi_addr: %p\n",  vi->eoi_addr);
+	printk(KERN_DEBUG "\t\teoi_data: %x\n",  vi->eoi_data);
+}
+
+
+static void
+iosapic_prt_isi(struct iosapic_info *isi)
+{
+	printk(KERN_DEBUG MODULE_NAME ": io_sapic_info at %p\n", isi);
+	printk(KERN_DEBUG "\t\tisi_hpa:       %lx\n", isi->isi_hpa);
+	printk(KERN_DEBUG "\t\tisi_status:    %x\n", isi->isi_status);
+	printk(KERN_DEBUG "\t\tisi_version:   %x\n", isi->isi_version);
+	printk(KERN_DEBUG "\t\tisi_vector:    %p\n", isi->isi_vector);
+}
+#endif /* DEBUG_IOSAPIC */