Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1480 commits)
  bonding: enable netpoll without checking link status
  xfrm: Refcount destination entry on xfrm_lookup
  net: introduce rx_handler results and logic around that
  bonding: get rid of IFF_SLAVE_INACTIVE netdev->priv_flag
  bonding: wrap slave state work
  net: get rid of multiple bond-related netdevice->priv_flags
  bonding: register slave pointer for rx_handler
  be2net: Bump up the version number
  be2net: Copyright notice change. Update to Emulex instead of ServerEngines
  e1000e: fix kconfig for crc32 dependency
  netfilter ebtables: fix xt_AUDIT to work with ebtables
  xen network backend driver
  bonding: Improve syslog message at device creation time
  bonding: Call netif_carrier_off after register_netdevice
  bonding: Incorrect TX queue offset
  net_sched: fix ip_tos2prio
  xfrm: fix __xfrm_route_forward()
  be2net: Fix UDP packet detected status in RX compl
  Phonet: fix aligned-mode pipe socket buffer header reserve
  netxen: support for GbE port settings
  ...

Fix up conflicts in drivers/staging/brcm80211/brcmsmac/wl_mac80211.c
with the staging updates.

3 files changed, 21 insertions, 12 deletions

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 35fda5ac8120..392a6c4b72e5 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -77,7 +77,6 @@ config NATIONAL_PHY
 	  Currently supports the DP83865 PHY.
 
 config STE10XP
-	depends on PHYLIB
 	tristate "Driver for STMicroelectronics STe10Xp PHYs"
 	---help---
 	  This is the driver for the STe100p and STe101p PHYs.
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 0fd1678bc5a9..590f902deb6b 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -19,13 +19,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/phy.h>
-
-#define	PHY_ID_KSZ9021			0x00221611
-#define	PHY_ID_KS8737			0x00221720
-#define	PHY_ID_KS8041			0x00221510
-#define	PHY_ID_KS8051			0x00221550
-/* both for ks8001 Rev. A/B, and for ks8721 Rev 3. */
-#define	PHY_ID_KS8001			0x0022161A
+#include <linux/micrel_phy.h>
 
 /* general Interrupt control/status reg in vendor specific block. */
 #define MII_KSZPHY_INTCS			0x1B
@@ -46,6 +40,7 @@
 #define KSZPHY_CTRL_INT_ACTIVE_HIGH		(1 << 9)
 #define KSZ9021_CTRL_INT_ACTIVE_HIGH		(1 << 14)
 #define KS8737_CTRL_INT_ACTIVE_HIGH		(1 << 14)
+#define KSZ8051_RMII_50MHZ_CLK			(1 << 7)
 
 static int kszphy_ack_interrupt(struct phy_device *phydev)
 {
@@ -106,6 +101,19 @@ static int kszphy_config_init(struct phy_device *phydev)
 	return 0;
 }
 
+static int ks8051_config_init(struct phy_device *phydev)
+{
+	int regval;
+
+	if (phydev->dev_flags & MICREL_PHY_50MHZ_CLK) {
+		regval = phy_read(phydev, MII_KSZPHY_CTRL);
+		regval |= KSZ8051_RMII_50MHZ_CLK;
+		phy_write(phydev, MII_KSZPHY_CTRL, regval);
+	}
+
+	return 0;
+}
+
 static struct phy_driver ks8737_driver = {
 	.phy_id		= PHY_ID_KS8737,
 	.phy_id_mask	= 0x00fffff0,
@@ -142,7 +150,7 @@ static struct phy_driver ks8051_driver = {
 	.features	= (PHY_BASIC_FEATURES | SUPPORTED_Pause
 				| SUPPORTED_Asym_Pause),
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
-	.config_init	= kszphy_config_init,
+	.config_init	= ks8051_config_init,
 	.config_aneg	= genphy_config_aneg,
 	.read_status	= genphy_read_status,
 	.ack_interrupt	= kszphy_ack_interrupt,
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index a8445c72fc13..f7670330f988 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -319,7 +319,8 @@ int phy_mii_ioctl(struct phy_device *phydev,
 		/* fall through */
 
 	case SIOCGMIIREG:
-		mii_data->val_out = phy_read(phydev, mii_data->reg_num);
+		mii_data->val_out = mdiobus_read(phydev->bus, mii_data->phy_id,
+						 mii_data->reg_num);
 		break;
 
 	case SIOCSMIIREG:
@@ -350,8 +351,9 @@ int phy_mii_ioctl(struct phy_device *phydev,
 			}
 		}
 
-		phy_write(phydev, mii_data->reg_num, val);
-		
+		mdiobus_write(phydev->bus, mii_data->phy_id,
+			      mii_data->reg_num, val);
+
 		if (mii_data->reg_num == MII_BMCR &&
 		    val & BMCR_RESET &&
 		    phydev->drv->config_init) {