Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 355 insertions, 0 deletions

diff --git a/drivers/net/3c523.h b/drivers/net/3c523.h
new file mode 100644
index 000000000000..7292f88b48e3
--- /dev/null
+++ b/drivers/net/3c523.h
@@ -0,0 +1,355 @@
+#ifndef _3c523_INCLUDE_
+#define _3c523_INCLUDE_
+/*
+	This is basically a hacked version of ni52.h, for the 3c523
+	Etherlink/MC.
+*/
+
+/*
+ * Intel i82586 Ethernet definitions
+ *
+ * This is an extension to the Linux operating system, and is covered by the
+ * same GNU General Public License that covers that work.
+ *
+ * Copyright 1995 by Chris Beauregard (cpbeaure@undergrad.math.uwaterloo.ca)
+ *
+ * See 3c523.c for details.
+ *
+ * $Header: /home/chrisb/linux-1.2.13-3c523/drivers/net/RCS/3c523.h,v 1.6 1996/01/20 05:09:00 chrisb Exp chrisb $
+ */
+
+/*
+ * where to find the System Configuration Pointer (SCP)
+ */
+#define SCP_DEFAULT_ADDRESS 0xfffff4
+
+
+/*
+ * System Configuration Pointer Struct
+ */
+
+struct scp_struct
+{
+  unsigned short zero_dum0;	/* has to be zero */
+  unsigned char  sysbus;	/* 0=16Bit,1=8Bit */
+  unsigned char  zero_dum1;	/* has to be zero for 586 */
+  unsigned short zero_dum2;
+  unsigned short zero_dum3;
+  char          *iscp;		/* pointer to the iscp-block */
+};
+
+
+/*
+ * Intermediate System Configuration Pointer (ISCP)
+ */
+struct iscp_struct
+{
+  unsigned char  busy;          /* 586 clears after successful init */
+  unsigned char  zero_dummy;    /* hast to be zero */
+  unsigned short scb_offset;    /* pointeroffset to the scb_base */
+  char          *scb_base;      /* base-address of all 16-bit offsets */
+};
+
+/*
+ * System Control Block (SCB)
+ */
+struct scb_struct
+{
+  unsigned short status;        /* status word */
+  unsigned short cmd;           /* command word */
+  unsigned short cbl_offset;    /* pointeroffset, command block list */
+  unsigned short rfa_offset;    /* pointeroffset, receive frame area */
+  unsigned short crc_errs;      /* CRC-Error counter */
+  unsigned short aln_errs;      /* alignmenterror counter */
+  unsigned short rsc_errs;      /* Resourceerror counter */
+  unsigned short ovrn_errs;     /* OVerrunerror counter */
+};
+
+/*
+ * possible command values for the command word
+ */
+#define RUC_MASK	0x0070	/* mask for RU commands */
+#define RUC_NOP		0x0000	/* NOP-command */
+#define RUC_START	0x0010	/* start RU */
+#define RUC_RESUME	0x0020	/* resume RU after suspend */
+#define RUC_SUSPEND	0x0030	/* suspend RU */
+#define RUC_ABORT	0x0040	/* abort receiver operation immediately */
+
+#define CUC_MASK	0x0700	/* mask for CU command */
+#define CUC_NOP		0x0000	/* NOP-command */
+#define CUC_START	0x0100	/* start execution of 1. cmd on the CBL */
+#define CUC_RESUME	0x0200	/* resume after suspend */
+#define CUC_SUSPEND	0x0300	/* Suspend CU */
+#define CUC_ABORT	0x0400	/* abort command operation immediately */
+
+#define ACK_MASK	0xf000	/* mask for ACK command */
+#define ACK_CX		0x8000	/* acknowledges STAT_CX */
+#define ACK_FR		0x4000	/* ack. STAT_FR */
+#define ACK_CNA		0x2000	/* ack. STAT_CNA */
+#define ACK_RNR		0x1000	/* ack. STAT_RNR */
+
+/*
+ * possible status values for the status word
+ */
+#define STAT_MASK	0xf000	/* mask for cause of interrupt */
+#define STAT_CX		0x8000	/* CU finished cmd with its I bit set */
+#define STAT_FR		0x4000	/* RU finished receiving a frame */
+#define STAT_CNA	0x2000	/* CU left active state */
+#define STAT_RNR	0x1000	/* RU left ready state */
+
+#define CU_STATUS	0x700	/* CU status, 0=idle */
+#define CU_SUSPEND	0x100	/* CU is suspended */
+#define CU_ACTIVE	0x200	/* CU is active */
+
+#define RU_STATUS	0x70	/* RU status, 0=idle */
+#define RU_SUSPEND	0x10	/* RU suspended */
+#define RU_NOSPACE	0x20	/* RU no resources */
+#define RU_READY	0x40	/* RU is ready */
+
+/*
+ * Receive Frame Descriptor (RFD)
+ */
+struct rfd_struct
+{
+  unsigned short status;	/* status word */
+  unsigned short last;		/* Bit15,Last Frame on List / Bit14,suspend */
+  unsigned short next;		/* linkoffset to next RFD */
+  unsigned short rbd_offset;	/* pointeroffset to RBD-buffer */
+  unsigned char  dest[6];	/* ethernet-address, destination */
+  unsigned char  source[6];	/* ethernet-address, source */
+  unsigned short length;	/* 802.3 frame-length */
+  unsigned short zero_dummy;	/* dummy */
+};
+
+#define RFD_LAST     0x8000	/* last: last rfd in the list */
+#define RFD_SUSP     0x4000	/* last: suspend RU after  */
+#define RFD_ERRMASK  0x0fe1     /* status: errormask */
+#define RFD_MATCHADD 0x0002     /* status: Destinationaddress !matches IA */
+#define RFD_RNR      0x0200	/* status: receiver out of resources */
+
+/*
+ * Receive Buffer Descriptor (RBD)
+ */
+struct rbd_struct 
+{
+  unsigned short status;	/* status word,number of used bytes in buff */
+  unsigned short next;		/* pointeroffset to next RBD */
+  char          *buffer;	/* receive buffer address pointer */
+  unsigned short size;		/* size of this buffer */
+  unsigned short zero_dummy;    /* dummy */
+};
+
+#define RBD_LAST	0x8000	/* last buffer */
+#define RBD_USED	0x4000	/* this buffer has data */
+#define RBD_MASK	0x3fff	/* size-mask for length */
+
+/*
+ * Statusvalues for Commands/RFD
+ */
+#define STAT_COMPL   0x8000	/* status: frame/command is complete */
+#define STAT_BUSY    0x4000	/* status: frame/command is busy */
+#define STAT_OK      0x2000	/* status: frame/command is ok */
+
+/*
+ * Action-Commands
+ */
+#define CMD_NOP		0x0000	/* NOP */
+#define CMD_IASETUP	0x0001	/* initial address setup command */
+#define CMD_CONFIGURE	0x0002	/* configure command */
+#define CMD_MCSETUP	0x0003	/* MC setup command */
+#define CMD_XMIT	0x0004	/* transmit command */
+#define CMD_TDR		0x0005	/* time domain reflectometer (TDR) command */
+#define CMD_DUMP	0x0006	/* dump command */
+#define CMD_DIAGNOSE	0x0007	/* diagnose command */
+
+/*
+ * Action command bits
+ */
+#define CMD_LAST	0x8000	/* indicates last command in the CBL */
+#define CMD_SUSPEND	0x4000	/* suspend CU after this CB */
+#define CMD_INT		0x2000	/* generate interrupt after execution */
+
+/*
+ * NOP - command
+ */
+struct nop_cmd_struct
+{
+  unsigned short cmd_status;	/* status of this command */
+  unsigned short cmd_cmd;       /* the command itself (+bits) */
+  unsigned short cmd_link;      /* offsetpointer to next command */
+};
+
+/*
+ * IA Setup command
+ */
+struct iasetup_cmd_struct 
+{
+  unsigned short cmd_status;
+  unsigned short cmd_cmd;
+  unsigned short cmd_link;
+  unsigned char  iaddr[6];
+};
+
+/*
+ * Configure command 
+ */
+struct configure_cmd_struct
+{
+  unsigned short cmd_status;
+  unsigned short cmd_cmd;
+  unsigned short cmd_link;
+  unsigned char  byte_cnt;   /* size of the config-cmd */
+  unsigned char  fifo;       /* fifo/recv monitor */
+  unsigned char  sav_bf;     /* save bad frames (bit7=1)*/
+  unsigned char  adr_len;    /* adr_len(0-2),al_loc(3),pream(4-5),loopbak(6-7)*/
+  unsigned char  priority;   /* lin_prio(0-2),exp_prio(4-6),bof_metd(7) */
+  unsigned char  ifs;        /* inter frame spacing */
+  unsigned char  time_low;   /* slot time low */
+  unsigned char  time_high;  /* slot time high(0-2) and max. retries(4-7) */
+  unsigned char  promisc;    /* promisc-mode(0) , et al (1-7) */
+  unsigned char  carr_coll;  /* carrier(0-3)/collision(4-7) stuff */
+  unsigned char  fram_len;   /* minimal frame len */
+  unsigned char  dummy;	     /* dummy */
+};
+
+/*
+ * Multicast Setup command 
+ */
+struct mcsetup_cmd_struct 
+{
+  unsigned short cmd_status;
+  unsigned short cmd_cmd;
+  unsigned short cmd_link;
+  unsigned short mc_cnt;		/* number of bytes in the MC-List */
+  unsigned char  mc_list[0][6];  	/* pointer to 6 bytes entries */
+};
+
+/*
+ * transmit command 
+ */
+struct transmit_cmd_struct 
+{
+  unsigned short cmd_status;
+  unsigned short cmd_cmd;
+  unsigned short cmd_link;
+  unsigned short tbd_offset;	/* pointeroffset to TBD */
+  unsigned char  dest[6];       /* destination address of the frame */
+  unsigned short length;	/* user defined: 802.3 length / Ether type */
+};
+
+#define TCMD_ERRMASK     0x0fa0
+#define TCMD_MAXCOLLMASK 0x000f
+#define TCMD_MAXCOLL     0x0020
+#define TCMD_HEARTBEAT   0x0040
+#define TCMD_DEFERRED    0x0080
+#define TCMD_UNDERRUN    0x0100
+#define TCMD_LOSTCTS     0x0200
+#define TCMD_NOCARRIER   0x0400
+#define TCMD_LATECOLL    0x0800
+
+struct tdr_cmd_struct
+{
+  unsigned short cmd_status;
+  unsigned short cmd_cmd;
+  unsigned short cmd_link;
+  unsigned short status;
+};
+
+#define TDR_LNK_OK	0x8000	/* No link problem identified */
+#define TDR_XCVR_PRB	0x4000	/* indicates a transceiver problem */
+#define TDR_ET_OPN	0x2000	/* open, no correct termination */
+#define TDR_ET_SRT	0x1000	/* TDR detected a short circuit */
+#define TDR_TIMEMASK	0x07ff	/* mask for the time field */
+
+/*
+ * Transmit Buffer Descriptor (TBD)
+ */
+struct tbd_struct
+{
+  unsigned short size;		/* size + EOF-Flag(15) */
+  unsigned short next;          /* pointeroffset to next TBD */
+  char          *buffer;        /* pointer to buffer */
+};
+
+#define TBD_LAST 0x8000         /* EOF-Flag, indicates last buffer in list */
+
+/*************************************************************************/
+/*
+Verbatim from the Crynwyr stuff:
+
+    The 3c523 responds with adapter code 0x6042 at slot
+registers xxx0 and xxx1.  The setup register is at xxx2 and
+contains the following bits:
+
+0: card enable
+2,1: csr address select
+    00 = 0300
+    01 = 1300
+    10 = 2300
+    11 = 3300
+4,3: shared memory address select
+    00 = 0c0000
+    01 = 0c8000
+    10 = 0d0000
+    11 = 0d8000
+5: set to disable on-board thinnet
+7,6: (read-only) shows selected irq
+    00 = 12
+    01 = 7
+    10 = 3
+    11 = 9
+
+The interrupt-select register is at xxx3 and uses one bit per irq.
+
+0: int 12
+1: int 7
+2: int 3
+3: int 9
+
+    Again, the documentation stresses that the setup register
+should never be written.  The interrupt-select register may be
+written with the value corresponding to bits 7.6 in
+the setup register to insure corret setup.
+*/
+
+/* Offsets from the base I/O address. */
+#define	ELMC_SA		0	/* first 6 bytes are IEEE network address */
+#define ELMC_CTRL	6	/* control & status register */
+#define ELMC_REVISION	7	/* revision register, first 4 bits only */
+#define ELMC_IO_EXTENT  8
+
+/* these are the bit selects for the port register 2 */
+#define ELMC_STATUS_ENABLED	0x01
+#define ELMC_STATUS_CSR_SELECT	0x06
+#define ELMC_STATUS_MEMORY_SELECT	0x18
+#define ELMC_STATUS_DISABLE_THIN	0x20
+#define ELMC_STATUS_IRQ_SELECT	0xc0
+
+/* this is the card id used in the detection code.  You might recognize
+it from @6042.adf */
+#define ELMC_MCA_ID 0x6042
+
+/*
+   The following define the bits for the control & status register
+
+   The bank select registers can be used if more than 16K of memory is
+   on the card.  For some stupid reason, bank 3 is the one for the
+   bottom 16K, and the card defaults to bank 0.  So we have to set the
+   bank to 3 before the card will even think of operating.  To get bank
+   3, set BS0 and BS1 to high (of course...)
+*/
+#define ELMC_CTRL_BS0	0x01	/* RW bank select */
+#define ELMC_CTRL_BS1	0x02	/* RW bank select */
+#define ELMC_CTRL_INTE	0x04	/* RW interrupt enable, assert high */
+#define ELMC_CTRL_INT	0x08	/* R interrupt active, assert high */
+/*#define ELMC_CTRL_*	0x10*/	/* reserved */
+#define ELMC_CTRL_LBK	0x20	/* RW loopback enable, assert high */
+#define ELMC_CTRL_CA	0x40	/* RW channel attention, assert high */
+#define ELMC_CTRL_RST	0x80	/* RW 82586 reset, assert low */
+
+/* some handy compound bits */
+
+/* normal operation should have bank 3 and RST high, ints enabled */
+#define ELMC_NORMAL (ELMC_CTRL_INTE|ELMC_CTRL_RST|0x3)
+
+#endif /* _3c523_INCLUDE_ */