dmaengine: qcom-adm: stop abusing slave_id config

The slave_id was previously used to pick one DMA slave instead of another,
but this is now done through the DMA descriptors in device tree.

For the qcom_adm driver, the configuration is documented in the DT
binding to contain a tuple of device identifier and a "crci" field,
but the implementation ends up using only a single cell for identifying
the slave, with the crci getting passed in nonstandard properties of
the device, and passed through the dma driver using the old slave_id
field. Part of the problem apparently is that the nand driver ends up
using only a single DMA request ID, but requires distinct values for
"crci" depending on the type of transfer.

Change both the dmaengine driver and the two slave drivers to allow
the documented binding to work in addition to the ad-hoc passing
of crci values. In order to no longer abuse the slave_id field, pass
the data using the "peripheral_config" mechanism instead.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-9-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

1 files changed, 12 insertions, 2 deletions

diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
index 04e6f7b26706..7c6efa3b6255 100644
--- a/drivers/mtd/nand/raw/qcom_nandc.c
+++ b/drivers/mtd/nand/raw/qcom_nandc.c
@@ -6,6 +6,7 @@
 #include <linux/clk.h>
 #include <linux/slab.h>
 #include <linux/bitops.h>
+#include <linux/dma/qcom_adm.h>
 #include <linux/dma-mapping.h>
 #include <linux/dmaengine.h>
 #include <linux/module.h>
@@ -952,6 +953,7 @@ static int prep_adm_dma_desc(struct qcom_nand_controller *nandc, bool read,
 	struct dma_async_tx_descriptor *dma_desc;
 	struct scatterlist *sgl;
 	struct dma_slave_config slave_conf;
+	struct qcom_adm_peripheral_config periph_conf = {};
 	enum dma_transfer_direction dir_eng;
 	int ret;
 
@@ -983,11 +985,19 @@ static int prep_adm_dma_desc(struct qcom_nand_controller *nandc, bool read,
 	if (read) {
 		slave_conf.src_maxburst = 16;
 		slave_conf.src_addr = nandc->base_dma + reg_off;
-		slave_conf.slave_id = nandc->data_crci;
+		if (nandc->data_crci) {
+			periph_conf.crci = nandc->data_crci;
+			slave_conf.peripheral_config = &periph_conf;
+			slave_conf.peripheral_size = sizeof(periph_conf);
+		}
 	} else {
 		slave_conf.dst_maxburst = 16;
 		slave_conf.dst_addr = nandc->base_dma + reg_off;
-		slave_conf.slave_id = nandc->cmd_crci;
+		if (nandc->cmd_crci) {
+			periph_conf.crci = nandc->cmd_crci;
+			slave_conf.peripheral_config = &periph_conf;
+			slave_conf.peripheral_size = sizeof(periph_conf);
+		}
 	}
 
 	ret = dmaengine_slave_config(nandc->chan, &slave_conf);