Merge git://git.infradead.org/mtd-2.6

* git://git.infradead.org/mtd-2.6: (226 commits)
  mtd: tests: annotate as DANGEROUS in Kconfig
  mtd: tests: don't use mtd0 as a default
  mtd: clean up usage of MTD_DOCPROBE_ADDRESS
  jffs2: add compr=lzo and compr=zlib options
  jffs2: implement mount option parsing and compression overriding
  mtd: nand: initialize ops.mode
  mtd: provide an alias for the redboot module name
  mtd: m25p80: don't probe device which has status of 'disabled'
  mtd: nand_h1900 never worked
  mtd: Add DiskOnChip G3 support
  mtd: m25p80: add EON flash EN25Q32B into spi flash id table
  mtd: mark block device queue as non-rotational
  mtd: r852: make r852_pm_ops static
  mtd: m25p80: add support for at25df321a spi data flash
  mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
  mtd: nand: switch `check_pattern()' to standard `memcmp()'
  mtd: nand: invalidate cache on unaligned reads
  mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
  mtd: nand: wait to set BBT version
  mtd: nand: scrub BBT on ECC errors
  ...

Fix up trivial conflicts:
 - arch/arm/mach-at91/board-usb-a9260.c
	Merged into board-usb-a926x.c
 - drivers/mtd/maps/lantiq-flash.c
	add_mtd_partitions -> mtd_device_register vs changed to use
	mtd_device_parse_register.

48 files changed, 4597 insertions, 1918 deletions

diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index dbfa0f7fb464..cce7b70824c3 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -83,16 +83,9 @@ config MTD_NAND_DENALI_SCRATCH_REG_ADDR
           scratch register here to enable this feature. On Intel Moorestown
           boards, the scratch register is at 0xFF108018.
 
-config MTD_NAND_EDB7312
-	tristate "Support for Cirrus Logic EBD7312 evaluation board"
-	depends on ARCH_EDB7312
-	help
-	  This enables the driver for the Cirrus Logic EBD7312 evaluation
-	  board to access the onboard NAND Flash.
-
 config MTD_NAND_H1900
 	tristate "iPAQ H1900 flash"
-	depends on ARCH_PXA
+	depends on ARCH_PXA && BROKEN
 	help
 	  This enables the driver for the iPAQ h1900 flash.
 
@@ -116,10 +109,11 @@ config MTD_NAND_AMS_DELTA
 	  Support for NAND flash on Amstrad E3 (Delta).
 
 config MTD_NAND_OMAP2
-	tristate "NAND Flash device on OMAP2 and OMAP3"
-	depends on ARM && (ARCH_OMAP2 || ARCH_OMAP3)
+	tristate "NAND Flash device on OMAP2, OMAP3 and OMAP4"
+	depends on ARM && (ARCH_OMAP2 || ARCH_OMAP3 || ARCH_OMAP4)
 	help
-          Support for NAND flash on Texas Instruments OMAP2 and OMAP3 platforms.
+          Support for NAND flash on Texas Instruments OMAP2, OMAP3 and OMAP4
+	  platforms.
 
 config MTD_NAND_IDS
 	tristate
@@ -423,6 +417,19 @@ config MTD_NAND_NANDSIM
 	  The simulator may simulate various NAND flash chips for the
 	  MTD nand layer.
 
+config MTD_NAND_GPMI_NAND
+        bool "GPMI NAND Flash Controller driver"
+        depends on MTD_NAND && (SOC_IMX23 || SOC_IMX28)
+	select MTD_PARTITIONS
+	select MTD_CMDLINE_PARTS
+        help
+	 Enables NAND Flash support for IMX23 or IMX28.
+	 The GPMI controller is very powerful, with the help of BCH
+	 module, it can do the hardware ECC. The GPMI supports several
+	 NAND flashs at the same time. The GPMI may conflicts with other
+	 block, such as SD card. So pay attention to it when you enable
+	 the GPMI.
+
 config MTD_NAND_PLATFORM
 	tristate "Support for generic platform NAND driver"
 	help
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 5745d831168e..618f4ba23699 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -13,7 +13,6 @@ obj-$(CONFIG_MTD_NAND_SPIA)		+= spia.o
 obj-$(CONFIG_MTD_NAND_AMS_DELTA)	+= ams-delta.o
 obj-$(CONFIG_MTD_NAND_AUTCPU12)		+= autcpu12.o
 obj-$(CONFIG_MTD_NAND_DENALI)		+= denali.o
-obj-$(CONFIG_MTD_NAND_EDB7312)		+= edb7312.o
 obj-$(CONFIG_MTD_NAND_AU1550)		+= au1550nd.o
 obj-$(CONFIG_MTD_NAND_BF5XX)		+= bf5xx_nand.o
 obj-$(CONFIG_MTD_NAND_PPCHAMELEONEVB)	+= ppchameleonevb.o
@@ -49,5 +48,6 @@ obj-$(CONFIG_MTD_NAND_BCM_UMI)		+= bcm_umi_nand.o nand_bcm_umi.o
 obj-$(CONFIG_MTD_NAND_MPC5121_NFC)	+= mpc5121_nfc.o
 obj-$(CONFIG_MTD_NAND_RICOH)		+= r852.o
 obj-$(CONFIG_MTD_NAND_JZ4740)		+= jz4740_nand.o
+obj-$(CONFIG_MTD_NAND_GPMI_NAND)	+= gpmi-nand/
 
 nand-objs := nand_base.o nand_bbt.o
diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c
index 55da20ccc7a8..23e5d77c39fc 100644
--- a/drivers/mtd/nand/atmel_nand.c
+++ b/drivers/mtd/nand/atmel_nand.c
@@ -161,37 +161,6 @@ static int atmel_nand_device_ready(struct mtd_info *mtd)
                 !!host->board->rdy_pin_active_low;
 }
 
-/*
- * Minimal-overhead PIO for data access.
- */
-static void atmel_read_buf8(struct mtd_info *mtd, u8 *buf, int len)
-{
-	struct nand_chip	*nand_chip = mtd->priv;
-
-	__raw_readsb(nand_chip->IO_ADDR_R, buf, len);
-}
-
-static void atmel_read_buf16(struct mtd_info *mtd, u8 *buf, int len)
-{
-	struct nand_chip	*nand_chip = mtd->priv;
-
-	__raw_readsw(nand_chip->IO_ADDR_R, buf, len / 2);
-}
-
-static void atmel_write_buf8(struct mtd_info *mtd, const u8 *buf, int len)
-{
-	struct nand_chip	*nand_chip = mtd->priv;
-
-	__raw_writesb(nand_chip->IO_ADDR_W, buf, len);
-}
-
-static void atmel_write_buf16(struct mtd_info *mtd, const u8 *buf, int len)
-{
-	struct nand_chip	*nand_chip = mtd->priv;
-
-	__raw_writesw(nand_chip->IO_ADDR_W, buf, len / 2);
-}
-
 static void dma_complete_func(void *completion)
 {
 	complete(completion);
@@ -266,33 +235,27 @@ err_buf:
 static void atmel_read_buf(struct mtd_info *mtd, u8 *buf, int len)
 {
 	struct nand_chip *chip = mtd->priv;
-	struct atmel_nand_host *host = chip->priv;
 
 	if (use_dma && len > mtd->oobsize)
 		/* only use DMA for bigger than oob size: better performances */
 		if (atmel_nand_dma_op(mtd, buf, len, 1) == 0)
 			return;
 
-	if (host->board->bus_width_16)
-		atmel_read_buf16(mtd, buf, len);
-	else
-		atmel_read_buf8(mtd, buf, len);
+	/* if no DMA operation possible, use PIO */
+	memcpy_fromio(buf, chip->IO_ADDR_R, len);
 }
 
 static void atmel_write_buf(struct mtd_info *mtd, const u8 *buf, int len)
 {
 	struct nand_chip *chip = mtd->priv;
-	struct atmel_nand_host *host = chip->priv;
 
 	if (use_dma && len > mtd->oobsize)
 		/* only use DMA for bigger than oob size: better performances */
 		if (atmel_nand_dma_op(mtd, (void *)buf, len, 0) == 0)
 			return;
 
-	if (host->board->bus_width_16)
-		atmel_write_buf16(mtd, buf, len);
-	else
-		atmel_write_buf8(mtd, buf, len);
+	/* if no DMA operation possible, use PIO */
+	memcpy_toio(chip->IO_ADDR_W, buf, len);
 }
 
 /*
@@ -481,10 +444,6 @@ static void atmel_nand_hwctl(struct mtd_info *mtd, int mode)
 	}
 }
 
-#ifdef CONFIG_MTD_CMDLINE_PARTS
-static const char *part_probes[] = { "cmdlinepart", NULL };
-#endif
-
 /*
  * Probe for the NAND device.
  */
@@ -496,8 +455,6 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
 	struct resource *regs;
 	struct resource *mem;
 	int res;
-	struct mtd_partition *partitions = NULL;
-	int num_partitions = 0;
 
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!mem) {
@@ -583,7 +540,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
 
 	if (on_flash_bbt) {
 		printk(KERN_INFO "atmel_nand: Use On Flash BBT\n");
-		nand_chip->options |= NAND_USE_FLASH_BBT;
+		nand_chip->bbt_options |= NAND_BBT_USE_FLASH;
 	}
 
 	if (!cpu_has_dma())
@@ -594,7 +551,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
 
 		dma_cap_zero(mask);
 		dma_cap_set(DMA_MEMCPY, mask);
-		host->dma_chan = dma_request_channel(mask, 0, NULL);
+		host->dma_chan = dma_request_channel(mask, NULL, NULL);
 		if (!host->dma_chan) {
 			dev_err(host->dev, "Failed to request DMA channel\n");
 			use_dma = 0;
@@ -655,27 +612,12 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
 		goto err_scan_tail;
 	}
 
-#ifdef CONFIG_MTD_CMDLINE_PARTS
 	mtd->name = "atmel_nand";
-	num_partitions = parse_mtd_partitions(mtd, part_probes,
-					      &partitions, 0);
-#endif
-	if (num_partitions <= 0 && host->board->partition_info)
-		partitions = host->board->partition_info(mtd->size,
-							 &num_partitions);
-
-	if ((!partitions) || (num_partitions == 0)) {
-		printk(KERN_ERR "atmel_nand: No partitions defined, or unsupported device.\n");
-		res = -ENXIO;
-		goto err_no_partitions;
-	}
-
-	res = mtd_device_register(mtd, partitions, num_partitions);
+	res = mtd_device_parse_register(mtd, NULL, 0,
+			host->board->parts, host->board->num_parts);
 	if (!res)
 		return res;
 
-err_no_partitions:
-	nand_release(mtd);
 err_scan_tail:
 err_scan_ident:
 err_no_card:
diff --git a/drivers/mtd/nand/au1550nd.c b/drivers/mtd/nand/au1550nd.c
index fa5736b9286c..7dd3700f2303 100644
--- a/drivers/mtd/nand/au1550nd.c
+++ b/drivers/mtd/nand/au1550nd.c
@@ -52,7 +52,7 @@ static const struct mtd_partition partition_info[] = {
  * au_read_byte -  read one byte from the chip
  * @mtd:	MTD device structure
  *
- *  read function for 8bit buswith
+ * read function for 8bit buswidth
  */
 static u_char au_read_byte(struct mtd_info *mtd)
 {
@@ -67,7 +67,7 @@ static u_char au_read_byte(struct mtd_info *mtd)
  * @mtd:	MTD device structure
  * @byte:	pointer to data byte to write
  *
- *  write function for 8it buswith
+ * write function for 8it buswidth
  */
 static void au_write_byte(struct mtd_info *mtd, u_char byte)
 {
@@ -77,11 +77,10 @@ static void au_write_byte(struct mtd_info *mtd, u_char byte)
 }
 
 /**
- * au_read_byte16 -  read one byte endianess aware from the chip
+ * au_read_byte16 -  read one byte endianness aware from the chip
  * @mtd:	MTD device structure
  *
- *  read function for 16bit buswith with
- * endianess conversion
+ * read function for 16bit buswidth with endianness conversion
  */
 static u_char au_read_byte16(struct mtd_info *mtd)
 {
@@ -92,12 +91,11 @@ static u_char au_read_byte16(struct mtd_info *mtd)
 }
 
 /**
- * au_write_byte16 -  write one byte endianess aware to the chip
+ * au_write_byte16 -  write one byte endianness aware to the chip
  * @mtd:	MTD device structure
  * @byte:	pointer to data byte to write
  *
- *  write function for 16bit buswith with
- * endianess conversion
+ * write function for 16bit buswidth with endianness conversion
  */
 static void au_write_byte16(struct mtd_info *mtd, u_char byte)
 {
@@ -110,8 +108,7 @@ static void au_write_byte16(struct mtd_info *mtd, u_char byte)
  * au_read_word -  read one word from the chip
  * @mtd:	MTD device structure
  *
- *  read function for 16bit buswith without
- * endianess conversion
+ * read function for 16bit buswidth without endianness conversion
  */
 static u16 au_read_word(struct mtd_info *mtd)
 {
@@ -127,7 +124,7 @@ static u16 au_read_word(struct mtd_info *mtd)
  * @buf:	data buffer
  * @len:	number of bytes to write
  *
- *  write function for 8bit buswith
+ * write function for 8bit buswidth
  */
 static void au_write_buf(struct mtd_info *mtd, const u_char *buf, int len)
 {
@@ -146,7 +143,7 @@ static void au_write_buf(struct mtd_info *mtd, const u_char *buf, int len)
  * @buf:	buffer to store date
  * @len:	number of bytes to read
  *
- *  read function for 8bit buswith
+ * read function for 8bit buswidth
  */
 static void au_read_buf(struct mtd_info *mtd, u_char *buf, int len)
 {
@@ -165,7 +162,7 @@ static void au_read_buf(struct mtd_info *mtd, u_char *buf, int len)
  * @buf:	buffer containing the data to compare
  * @len:	number of bytes to compare
  *
- *  verify function for 8bit buswith
+ * verify function for 8bit buswidth
  */
 static int au_verify_buf(struct mtd_info *mtd, const u_char *buf, int len)
 {
@@ -187,7 +184,7 @@ static int au_verify_buf(struct mtd_info *mtd, const u_char *buf, int len)
  * @buf:	data buffer
  * @len:	number of bytes to write
  *
- *  write function for 16bit buswith
+ * write function for 16bit buswidth
  */
 static void au_write_buf16(struct mtd_info *mtd, const u_char *buf, int len)
 {
@@ -209,7 +206,7 @@ static void au_write_buf16(struct mtd_info *mtd, const u_char *buf, int len)
  * @buf:	buffer to store date
  * @len:	number of bytes to read
  *
- *  read function for 16bit buswith
+ * read function for 16bit buswidth
  */
 static void au_read_buf16(struct mtd_info *mtd, u_char *buf, int len)
 {
@@ -230,7 +227,7 @@ static void au_read_buf16(struct mtd_info *mtd, u_char *buf, int len)
  * @buf:	buffer containing the data to compare
  * @len:	number of bytes to compare
  *
- *  verify function for 16bit buswith
+ * verify function for 16bit buswidth
  */
 static int au_verify_buf16(struct mtd_info *mtd, const u_char *buf, int len)
 {
diff --git a/drivers/mtd/nand/autcpu12.c b/drivers/mtd/nand/autcpu12.c
index eddc9a224985..2e42ec2e8ff4 100644
--- a/drivers/mtd/nand/autcpu12.c
+++ b/drivers/mtd/nand/autcpu12.c
@@ -172,9 +172,9 @@ static int __init autcpu12_init(void)
 
 	/* Enable the following for a flash based bad block table */
 	/*
-	   this->options = NAND_USE_FLASH_BBT;
+	   this->bbt_options = NAND_BBT_USE_FLASH;
 	 */
-	this->options = NAND_USE_FLASH_BBT;
+	this->bbt_options = NAND_BBT_USE_FLASH;
 
 	/* Scan to find existence of the device */
 	if (nand_scan(autcpu12_mtd, 1)) {
diff --git a/drivers/mtd/nand/bcm_umi_nand.c b/drivers/mtd/nand/bcm_umi_nand.c
index 8c569e454dc5..46b58d672847 100644
--- a/drivers/mtd/nand/bcm_umi_nand.c
+++ b/drivers/mtd/nand/bcm_umi_nand.c
@@ -52,8 +52,6 @@
 static const __devinitconst char gBanner[] = KERN_INFO \
 	"BCM UMI MTD NAND Driver: 1.00\n";
 
-const char *part_probes[] = { "cmdlinepart", NULL };
-
 #if NAND_ECC_BCH
 static uint8_t scan_ff_pattern[] = { 0xff };
 
@@ -376,16 +374,18 @@ static int __devinit bcm_umi_nand_probe(struct platform_device *pdev)
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 
-	if (!r)
-		return -ENXIO;
+	if (!r) {
+		err = -ENXIO;
+		goto out_free;
+	}
 
 	/* map physical address */
 	bcm_umi_io_base = ioremap(r->start, resource_size(r));
 
 	if (!bcm_umi_io_base) {
 		printk(KERN_ERR "ioremap to access BCM UMI NAND chip failed\n");
-		kfree(board_mtd);
-		return -EIO;
+		err = -EIO;
+		goto out_free;
 	}
 
 	/* Get pointer to private data */
@@ -401,9 +401,8 @@ static int __devinit bcm_umi_nand_probe(struct platform_device *pdev)
 	/* Initialize the NAND hardware.  */
 	if (bcm_umi_nand_inithw() < 0) {
 		printk(KERN_ERR "BCM UMI NAND chip could not be initialized\n");
-		iounmap(bcm_umi_io_base);
-		kfree(board_mtd);
-		return -EIO;
+		err = -EIO;
+		goto out_unmap;
 	}
 
 	/* Set address of NAND IO lines */
@@ -436,7 +435,7 @@ static int __devinit bcm_umi_nand_probe(struct platform_device *pdev)
 #if USE_DMA
 	err = nand_dma_init();
 	if (err != 0)
-		return err;
+		goto out_unmap;
 #endif
 
 	/* Figure out the size of the device that we have.
@@ -447,9 +446,7 @@ static int __devinit bcm_umi_nand_probe(struct platform_device *pdev)
 	err = nand_scan_ident(board_mtd, 1, NULL);
 	if (err) {
 		printk(KERN_ERR "nand_scan failed: %d\n", err);
-		iounmap(bcm_umi_io_base);
-		kfree(board_mtd);
-		return err;
+		goto out_unmap;
 	}
 
 	/* Now that we know the nand size, we can setup the ECC layout */
@@ -468,13 +465,14 @@ static int __devinit bcm_umi_nand_probe(struct platform_device *pdev)
 		{
 			printk(KERN_ERR "NAND - Unrecognized pagesize: %d\n",
 					 board_mtd->writesize);
-			return -EINVAL;
+			err = -EINVAL;
+			goto out_unmap;
 		}
 	}
 
 #if NAND_ECC_BCH
 	if (board_mtd->writesize > 512) {
-		if (this->options & NAND_USE_FLASH_BBT)
+		if (this->bbt_options & NAND_BBT_USE_FLASH)
 			largepage_bbt.options = NAND_BBT_SCAN2NDPAGE;
 		this->badblock_pattern = &largepage_bbt;
 	}
@@ -485,33 +483,20 @@ static int __devinit bcm_umi_nand_probe(struct platform_device *pdev)
 	err = nand_scan_tail(board_mtd);
 	if (err) {
 		printk(KERN_ERR "nand_scan failed: %d\n", err);
-		iounmap(bcm_umi_io_base);
-		kfree(board_mtd);
-		return err;
+		goto out_unmap;
 	}
 
 	/* Register the partitions */
-	{
-		int nr_partitions;
-		struct mtd_partition *partition_info;
-
-		board_mtd->name = "bcm_umi-nand";
-		nr_partitions =
-		    parse_mtd_partitions(board_mtd, part_probes,
-					 &partition_info, 0);
-
-		if (nr_partitions <= 0) {
-			printk(KERN_ERR "BCM UMI NAND: Too few partitions - %d\n",
-			       nr_partitions);
-			iounmap(bcm_umi_io_base);
-			kfree(board_mtd);
-			return -EIO;
-		}
-		mtd_device_register(board_mtd, partition_info, nr_partitions);
-	}
+	board_mtd->name = "bcm_umi-nand";
+	mtd_device_parse_register(board_mtd, NULL, 0, NULL, 0);
 
 	/* Return happy */
 	return 0;
+out_unmap:
+	iounmap(bcm_umi_io_base);
+out_free:
+	kfree(board_mtd);
+	return err;
 }
 
 static int bcm_umi_nand_remove(struct platform_device *pdev)
diff --git a/drivers/mtd/nand/cafe_nand.c b/drivers/mtd/nand/cafe_nand.c
index 7c8df837d3b8..72d3f23490c5 100644
--- a/drivers/mtd/nand/cafe_nand.c
+++ b/drivers/mtd/nand/cafe_nand.c
@@ -58,7 +58,6 @@
 
 struct cafe_priv {
 	struct nand_chip nand;
-	struct mtd_partition *parts;
 	struct pci_dev *pdev;
 	void __iomem *mmio;
 	struct rs_control *rs;
@@ -372,7 +371,7 @@ static int cafe_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
 	return 1;
 }
 /**
- * cafe_nand_read_page_syndrome - {REPLACABLE] hardware ecc syndrom based page read
+ * cafe_nand_read_page_syndrome - [REPLACEABLE] hardware ecc syndrome based page read
  * @mtd:	mtd info structure
  * @chip:	nand chip info structure
  * @buf:	buffer to store read data
@@ -631,8 +630,6 @@ static int __devinit cafe_nand_probe(struct pci_dev *pdev,
 	struct cafe_priv *cafe;
 	uint32_t ctrl;
 	int err = 0;
-	struct mtd_partition *parts;
-	int nr_parts;
 
 	/* Very old versions shared the same PCI ident for all three
 	   functions on the chip. Verify the class too... */
@@ -687,7 +684,8 @@ static int __devinit cafe_nand_probe(struct pci_dev *pdev,
 	cafe->nand.chip_delay = 0;
 
 	/* Enable the following for a flash based bad block table */
-	cafe->nand.options = NAND_USE_FLASH_BBT | NAND_NO_AUTOINCR | NAND_OWN_BUFFERS;
+	cafe->nand.bbt_options = NAND_BBT_USE_FLASH;
+	cafe->nand.options = NAND_NO_AUTOINCR | NAND_OWN_BUFFERS;
 
 	if (skipbbt) {
 		cafe->nand.options |= NAND_SKIP_BBTSCAN;
@@ -800,18 +798,9 @@ static int __devinit cafe_nand_probe(struct pci_dev *pdev,
 
 	pci_set_drvdata(pdev, mtd);
 
-	/* We register the whole device first, separate from the partitions */
-	mtd_device_register(mtd, NULL, 0);
-
-#ifdef CONFIG_MTD_CMDLINE_PARTS
 	mtd->name = "cafe_nand";
-#endif
-	nr_parts = parse_mtd_partitions(mtd, part_probes, &parts, 0);
-	if (nr_parts > 0) {
-		cafe->parts = parts;
-		dev_info(&cafe->pdev->dev, "%d partitions found\n", nr_parts);
-		mtd_device_register(mtd, parts, nr_parts);
-	}
+	mtd_device_parse_register(mtd, part_probes, 0, NULL, 0);
+
 	goto out;
 
  out_irq:
diff --git a/drivers/mtd/nand/cmx270_nand.c b/drivers/mtd/nand/cmx270_nand.c
index be33b0f4634d..737ef9a04fdb 100644
--- a/drivers/mtd/nand/cmx270_nand.c
+++ b/drivers/mtd/nand/cmx270_nand.c
@@ -51,8 +51,6 @@ static struct mtd_partition partition_info[] = {
 };
 #define NUM_PARTITIONS (ARRAY_SIZE(partition_info))
 
-const char *part_probes[] = { "cmdlinepart", NULL };
-
 static u_char cmx270_read_byte(struct mtd_info *mtd)
 {
 	struct nand_chip *this = mtd->priv;
@@ -152,9 +150,6 @@ static int cmx270_device_ready(struct mtd_info *mtd)
 static int __init cmx270_init(void)
 {
 	struct nand_chip *this;
-	const char *part_type;
-	struct mtd_partition *mtd_parts;
-	int mtd_parts_nb = 0;
 	int ret;
 
 	if (!(machine_is_armcore() && cpu_is_pxa27x()))
@@ -223,23 +218,9 @@ static int __init cmx270_init(void)
 		goto err_scan;
 	}
 
-#ifdef CONFIG_MTD_CMDLINE_PARTS
-	mtd_parts_nb = parse_mtd_partitions(cmx270_nand_mtd, part_probes,
-					    &mtd_parts, 0);
-	if (mtd_parts_nb > 0)
-		part_type = "command line";
-	else
-		mtd_parts_nb = 0;
-#endif
-	if (!mtd_parts_nb) {
-		mtd_parts = partition_info;
-		mtd_parts_nb = NUM_PARTITIONS;
-		part_type = "static";
-	}
-
 	/* Register the partitions */
-	pr_notice("Using %s partition definition\n", part_type);
-	ret = mtd_device_register(cmx270_nand_mtd, mtd_parts, mtd_parts_nb);
+	ret = mtd_device_parse_register(cmx270_nand_mtd, NULL, 0,
+					partition_info, NUM_PARTITIONS);
 	if (ret)
 		goto err_scan;
 
diff --git a/drivers/mtd/nand/cs553x_nand.c b/drivers/mtd/nand/cs553x_nand.c
index f59ad1f2d5db..414afa793563 100644
--- a/drivers/mtd/nand/cs553x_nand.c
+++ b/drivers/mtd/nand/cs553x_nand.c
@@ -239,7 +239,8 @@ static int __init cs553x_init_one(int cs, int mmio, unsigned long adr)
 	this->ecc.correct  = nand_correct_data;
 
 	/* Enable the following for a flash based bad block table */
-	this->options = NAND_USE_FLASH_BBT | NAND_NO_AUTOINCR;
+	this->bbt_options = NAND_BBT_USE_FLASH;
+	this->options = NAND_NO_AUTOINCR;
 
 	/* Scan to find existence of the device */
 	if (nand_scan(new_mtd, 1)) {
@@ -277,15 +278,11 @@ static int is_geode(void)
 	return 0;
 }
 
-static const char *part_probes[] = { "cmdlinepart", NULL };
-
 static int __init cs553x_init(void)
 {
 	int err = -ENXIO;
 	int i;
 	uint64_t val;
-	int mtd_parts_nb = 0;
-	struct mtd_partition *mtd_parts = NULL;
 
 	/* If the CPU isn't a Geode GX or LX, abort */
 	if (!is_geode())
@@ -315,13 +312,9 @@ static int __init cs553x_init(void)
 	   do mtdconcat etc. if we want to. */
 	for (i = 0; i < NR_CS553X_CONTROLLERS; i++) {
 		if (cs553x_mtd[i]) {
-
 			/* If any devices registered, return success. Else the last error. */
-			mtd_parts_nb = parse_mtd_partitions(cs553x_mtd[i], part_probes, &mtd_parts, 0);
-			if (mtd_parts_nb > 0)
-				printk(KERN_NOTICE "Using command line partition definition\n");
-			mtd_device_register(cs553x_mtd[i], mtd_parts,
-					    mtd_parts_nb);
+			mtd_device_parse_register(cs553x_mtd[i], NULL, 0,
+						  NULL, 0);
 			err = 0;
 		}
 	}
diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
index 1f34951ae1a7..c153e1f77f90 100644
--- a/drivers/mtd/nand/davinci_nand.c
+++ b/drivers/mtd/nand/davinci_nand.c
@@ -57,7 +57,6 @@ struct davinci_nand_info {
 
 	struct device		*dev;
 	struct clk		*clk;
-	bool			partitioned;
 
 	bool			is_readmode;
 
@@ -530,8 +529,6 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
 	int				ret;
 	uint32_t			val;
 	nand_ecc_modes_t		ecc_mode;
-	struct mtd_partition		*mtd_parts = NULL;
-	int				mtd_parts_nb = 0;
 
 	/* insist on board-specific configuration */
 	if (!pdata)
@@ -581,7 +578,9 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
 	info->chip.chip_delay	= 0;
 	info->chip.select_chip	= nand_davinci_select_chip;
 
-	/* options such as NAND_USE_FLASH_BBT or 16-bit widths */
+	/* options such as NAND_BBT_USE_FLASH */
+	info->chip.bbt_options	= pdata->bbt_options;
+	/* options such as 16-bit widths */
 	info->chip.options	= pdata->options;
 	info->chip.bbt_td	= pdata->bbt_td;
 	info->chip.bbt_md	= pdata->bbt_md;
@@ -751,33 +750,8 @@ syndrome_done:
 	if (ret < 0)
 		goto err_scan;
 
-	if (mtd_has_cmdlinepart()) {
-		static const char *probes[] __initconst = {
-			"cmdlinepart", NULL
-		};
-
-		mtd_parts_nb = parse_mtd_partitions(&info->mtd, probes,
-						    &mtd_parts, 0);
-	}
-
-	if (mtd_parts_nb <= 0) {
-		mtd_parts = pdata->parts;
-		mtd_parts_nb = pdata->nr_parts;
-	}
-
-	/* Register any partitions */
-	if (mtd_parts_nb > 0) {
-		ret = mtd_device_register(&info->mtd, mtd_parts,
-					  mtd_parts_nb);
-		if (ret == 0)
-			info->partitioned = true;
-	}
-
-	/* If there's no partition info, just package the whole chip
-	 * as a single MTD device.
-	 */
-	if (!info->partitioned)
-		ret = mtd_device_register(&info->mtd, NULL, 0) ? -ENODEV : 0;
+	ret = mtd_device_parse_register(&info->mtd, NULL, 0,
+			pdata->parts, pdata->nr_parts);
 
 	if (ret < 0)
 		goto err_scan;
@@ -816,9 +790,6 @@ err_nomem:
 static int __exit nand_davinci_remove(struct platform_device *pdev)
 {
 	struct davinci_nand_info *info = platform_get_drvdata(pdev);
-	int status;
-
-	status = mtd_device_unregister(&info->mtd);
 
 	spin_lock_irq(&davinci_nand_lock);
 	if (info->chip.ecc.mode == NAND_ECC_HW_SYNDROME)
diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c
index d5276218945f..3984d488f9ab 100644
--- a/drivers/mtd/nand/denali.c
+++ b/drivers/mtd/nand/denali.c
@@ -1346,6 +1346,7 @@ static void denali_hw_init(struct denali_nand_info *denali)
 	 * */
 	denali->bbtskipbytes = ioread32(denali->flash_reg +
 						SPARE_AREA_SKIP_BYTES);
+	detect_max_banks(denali);
 	denali_nand_reset(denali);
 	iowrite32(0x0F, denali->flash_reg + RB_PIN_ENABLED);
 	iowrite32(CHIP_EN_DONT_CARE__FLAG,
@@ -1356,7 +1357,6 @@ static void denali_hw_init(struct denali_nand_info *denali)
 	/* Should set value for these registers when init */
 	iowrite32(0, denali->flash_reg + TWO_ROW_ADDR_CYCLES);
 	iowrite32(1, denali->flash_reg + ECC_ENABLE);
-	detect_max_banks(denali);
 	denali_nand_timing_set(denali);
 	denali_irq_init(denali);
 }
@@ -1577,7 +1577,8 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	denali->nand.bbt_md = &bbt_mirror_descr;
 
 	/* skip the scan for now until we have OOB read and write support */
-	denali->nand.options |= NAND_USE_FLASH_BBT | NAND_SKIP_BBTSCAN;
+	denali->nand.bbt_options |= NAND_BBT_USE_FLASH;
+	denali->nand.options |= NAND_SKIP_BBTSCAN;
 	denali->nand.ecc.mode = NAND_ECC_HW_SYNDROME;
 
 	/* Denali Controller only support 15bit and 8bit ECC in MRST,
@@ -1676,7 +1677,6 @@ static void denali_pci_remove(struct pci_dev *dev)
 	struct denali_nand_info *denali = pci_get_drvdata(dev);
 
 	nand_release(&denali->mtd);
-	mtd_device_unregister(&denali->mtd);
 
 	denali_irq_cleanup(dev->irq, denali);
 
diff --git a/drivers/mtd/nand/diskonchip.c b/drivers/mtd/nand/diskonchip.c
index e1b84cb90f0d..5780dbab6113 100644
--- a/drivers/mtd/nand/diskonchip.c
+++ b/drivers/mtd/nand/diskonchip.c
@@ -133,7 +133,7 @@ static struct rs_control *rs_decoder;
 
 /*
  * The HW decoder in the DoC ASIC's provides us a error syndrome,
- * which we must convert to a standard syndrom usable by the generic
+ * which we must convert to a standard syndrome usable by the generic
  * Reed-Solomon library code.
  *
  * Fabrice Bellard figured this out in the old docecc code. I added
@@ -154,7 +154,7 @@ static int doc_ecc_decode(struct rs_control *rs, uint8_t *data, uint8_t *ecc)
 	ds[3] = ((ecc[3] & 0xc0) >> 6) | ((ecc[0] & 0xff) << 2);
 	parity = ecc[1];
 
-	/* Initialize the syndrom buffer */
+	/* Initialize the syndrome buffer */
 	for (i = 0; i < NROOTS; i++)
 		s[i] = ds[0];
 	/*
@@ -1032,7 +1032,7 @@ static int doc200x_correct_data(struct mtd_info *mtd, u_char *dat,
 		WriteDOC(DOC_ECC_DIS, docptr, Mplus_ECCConf);
 	else
 		WriteDOC(DOC_ECC_DIS, docptr, ECCConf);
-	if (no_ecc_failures && (ret == -EBADMSG)) {
+	if (no_ecc_failures && mtd_is_eccerr(ret)) {
 		printk(KERN_ERR "suppressing ECC failure\n");
 		ret = 0;
 	}
@@ -1653,7 +1653,7 @@ static int __init doc_probe(unsigned long physadr)
 	nand->ecc.mode		= NAND_ECC_HW_SYNDROME;
 	nand->ecc.size		= 512;
 	nand->ecc.bytes		= 6;
-	nand->options		= NAND_USE_FLASH_BBT;
+	nand->bbt_options	= NAND_BBT_USE_FLASH;
 
 	doc->physadr		= physadr;
 	doc->virtadr		= virtadr;
diff --git a/drivers/mtd/nand/edb7312.c b/drivers/mtd/nand/edb7312.c
deleted file mode 100644
index 8400d0f6dada..000000000000
--- a/drivers/mtd/nand/edb7312.c
+++ /dev/null
@@ -1,203 +0,0 @@
-/*
- *  drivers/mtd/nand/edb7312.c
- *
- *  Copyright (C) 2002 Marius Gröger (mag@sysgo.de)
- *
- *  Derived from drivers/mtd/nand/autcpu12.c
- *       Copyright (c) 2001 Thomas Gleixner (gleixner@autronix.de)
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  Overview:
- *   This is a device driver for the NAND flash device found on the
- *   CLEP7312 board which utilizes the Toshiba TC58V64AFT part. This is
- *   a 64Mibit (8MiB x 8 bits) NAND flash device.
- */
-
-#include <linux/slab.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-#include <asm/io.h>
-#include <mach/hardware.h>	/* for CLPS7111_VIRT_BASE */
-#include <asm/sizes.h>
-#include <asm/hardware/clps7111.h>
-
-/*
- * MTD structure for EDB7312 board
- */
-static struct mtd_info *ep7312_mtd = NULL;
-
-/*
- * Values specific to the EDB7312 board (used with EP7312 processor)
- */
-#define EP7312_FIO_PBASE 0x10000000	/* Phys address of flash */
-#define EP7312_PXDR	0x0001	/*
-				 * IO offset to Port B data register
-				 * where the CLE, ALE and NCE pins
-				 * are wired to.
-				 */
-#define EP7312_PXDDR	0x0041	/*
-				 * IO offset to Port B data direction
-				 * register so we can control the IO
-				 * lines.
-				 */
-
-/*
- * Module stuff
- */
-
-static unsigned long ep7312_fio_pbase = EP7312_FIO_PBASE;
-static void __iomem *ep7312_pxdr = (void __iomem *)EP7312_PXDR;
-static void __iomem *ep7312_pxddr = (void __iomem *)EP7312_PXDDR;
-
-/*
- * Define static partitions for flash device
- */
-static struct mtd_partition partition_info[] = {
-	{.name = "EP7312 Nand Flash",
-	 .offset = 0,
-	 .size = 8 * 1024 * 1024}
-};
-
-#define NUM_PARTITIONS 1
-
-/*
- *	hardware specific access to control-lines
- *
- *	NAND_NCE: bit 0 -> bit 6 (bit 7 = 1)
- *	NAND_CLE: bit 1 -> bit 4
- *	NAND_ALE: bit 2 -> bit 5
- */
-static void ep7312_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
-	struct nand_chip *chip = mtd->priv;
-
-	if (ctrl & NAND_CTRL_CHANGE) {
-		unsigned char bits = 0x80;
-
-		bits |= (ctrl & (NAND_CLE | NAND_ALE)) << 3;
-		bits |= (ctrl & NAND_NCE) ? 0x00 : 0x40;
-
-		clps_writeb((clps_readb(ep7312_pxdr)  & 0xF0) | bits,
-			    ep7312_pxdr);
-	}
-	if (cmd != NAND_CMD_NONE)
-		writeb(cmd, chip->IO_ADDR_W);
-}
-
-/*
- *	read device ready pin
- */
-static int ep7312_device_ready(struct mtd_info *mtd)
-{
-	return 1;
-}
-
-const char *part_probes[] = { "cmdlinepart", NULL };
-
-/*
- * Main initialization routine
- */
-static int __init ep7312_init(void)
-{
-	struct nand_chip *this;
-	const char *part_type = 0;
-	int mtd_parts_nb = 0;
-	struct mtd_partition *mtd_parts = 0;
-	void __iomem *ep7312_fio_base;
-
-	/* Allocate memory for MTD device structure and private data */
-	ep7312_mtd = kmalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip), GFP_KERNEL);
-	if (!ep7312_mtd) {
-		printk("Unable to allocate EDB7312 NAND MTD device structure.\n");
-		return -ENOMEM;
-	}
-
-	/* map physical address */
-	ep7312_fio_base = ioremap(ep7312_fio_pbase, SZ_1K);
-	if (!ep7312_fio_base) {
-		printk("ioremap EDB7312 NAND flash failed\n");
-		kfree(ep7312_mtd);
-		return -EIO;
-	}
-
-	/* Get pointer to private data */
-	this = (struct nand_chip *)(&ep7312_mtd[1]);
-
-	/* Initialize structures */
-	memset(ep7312_mtd, 0, sizeof(struct mtd_info));
-	memset(this, 0, sizeof(struct nand_chip));
-
-	/* Link the private data with the MTD structure */
-	ep7312_mtd->priv = this;
-	ep7312_mtd->owner = THIS_MODULE;
-
-	/*
-	 * Set GPIO Port B control register so that the pins are configured
-	 * to be outputs for controlling the NAND flash.
-	 */
-	clps_writeb(0xf0, ep7312_pxddr);
-
-	/* insert callbacks */
-	this->IO_ADDR_R = ep7312_fio_base;
-	this->IO_ADDR_W = ep7312_fio_base;
-	this->cmd_ctrl = ep7312_hwcontrol;
-	this->dev_ready = ep7312_device_ready;
-	/* 15 us command delay time */
-	this->chip_delay = 15;
-
-	/* Scan to find existence of the device */
-	if (nand_scan(ep7312_mtd, 1)) {
-		iounmap((void *)ep7312_fio_base);
-		kfree(ep7312_mtd);
-		return -ENXIO;
-	}
-	ep7312_mtd->name = "edb7312-nand";
-	mtd_parts_nb = parse_mtd_partitions(ep7312_mtd, part_probes, &mtd_parts, 0);
-	if (mtd_parts_nb > 0)
-		part_type = "command line";
-	else
-		mtd_parts_nb = 0;
-	if (mtd_parts_nb == 0) {
-		mtd_parts = partition_info;
-		mtd_parts_nb = NUM_PARTITIONS;
-		part_type = "static";
-	}
-
-	/* Register the partitions */
-	printk(KERN_NOTICE "Using %s partition definition\n", part_type);
-	mtd_device_register(ep7312_mtd, mtd_parts, mtd_parts_nb);
-
-	/* Return happy */
-	return 0;
-}
-
-module_init(ep7312_init);
-
-/*
- * Clean up routine
- */
-static void __exit ep7312_cleanup(void)
-{
-	struct nand_chip *this = (struct nand_chip *)&ep7312_mtd[1];
-
-	/* Release resources, unregister device */
-	nand_release(ap7312_mtd);
-
-	/* Release io resource */
-	iounmap(this->IO_ADDR_R);
-
-	/* Free the MTD device structure */
-	kfree(ep7312_mtd);
-}
-
-module_exit(ep7312_cleanup);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Marius Groeger <mag@sysgo.de>");
-MODULE_DESCRIPTION("MTD map driver for Cogent EDB7312 board");
diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c
index 33d8aad8bba5..eedd8ee2c9ac 100644
--- a/drivers/mtd/nand/fsl_elbc_nand.c
+++ b/drivers/mtd/nand/fsl_elbc_nand.c
@@ -75,7 +75,6 @@ struct fsl_elbc_fcm_ctrl {
 	unsigned int use_mdr;    /* Non zero if the MDR is to be set      */
 	unsigned int oob;        /* Non zero if operating on OOB data     */
 	unsigned int counter;	 /* counter for the initializations	  */
-	char *oob_poi;           /* Place to write ECC after read back    */
 };
 
 /* These map to the positions used by the FCM hardware ECC generator */
@@ -244,6 +243,25 @@ static int fsl_elbc_run_command(struct mtd_info *mtd)
 		return -EIO;
 	}
 
+	if (chip->ecc.mode != NAND_ECC_HW)
+		return 0;
+
+	if (elbc_fcm_ctrl->read_bytes == mtd->writesize + mtd->oobsize) {
+		uint32_t lteccr = in_be32(&lbc->lteccr);
+		/*
+		 * if command was a full page read and the ELBC
+		 * has the LTECCR register, then bits 12-15 (ppc order) of
+		 * LTECCR indicates which 512 byte sub-pages had fixed errors.
+		 * bits 28-31 are uncorrectable errors, marked elsewhere.
+		 * for small page nand only 1 bit is used.
+		 * if the ELBC doesn't have the lteccr register it reads 0
+		 */
+		if (lteccr & 0x000F000F)
+			out_be32(&lbc->lteccr, 0x000F000F); /* clear lteccr */
+		if (lteccr & 0x000F0000)
+			mtd->ecc_stats.corrected++;
+	}
+
 	return 0;
 }
 
@@ -435,7 +453,6 @@ static void fsl_elbc_cmdfunc(struct mtd_info *mtd, unsigned int command,
 
 	/* PAGEPROG reuses all of the setup from SEQIN and adds the length */
 	case NAND_CMD_PAGEPROG: {
-		int full_page;
 		dev_vdbg(priv->dev,
 		         "fsl_elbc_cmdfunc: NAND_CMD_PAGEPROG "
 			 "writing %d bytes.\n", elbc_fcm_ctrl->index);
@@ -445,34 +462,12 @@ static void fsl_elbc_cmdfunc(struct mtd_info *mtd, unsigned int command,
 		 * write so the HW generates the ECC.
 		 */
 		if (elbc_fcm_ctrl->oob || elbc_fcm_ctrl->column != 0 ||
-		    elbc_fcm_ctrl->index != mtd->writesize + mtd->oobsize) {
+		    elbc_fcm_ctrl->index != mtd->writesize + mtd->oobsize)
 			out_be32(&lbc->fbcr, elbc_fcm_ctrl->index);
-			full_page = 0;
-		} else {
+		else
 			out_be32(&lbc->fbcr, 0);
-			full_page = 1;
-		}
 
 		fsl_elbc_run_command(mtd);
-
-		/* Read back the page in order to fill in the ECC for the
-		 * caller.  Is this really needed?
-		 */
-		if (full_page && elbc_fcm_ctrl->oob_poi) {
-			out_be32(&lbc->fbcr, 3);
-			set_addr(mtd, 6, page_addr, 1);
-
-			elbc_fcm_ctrl->read_bytes = mtd->writesize + 9;
-
-			fsl_elbc_do_read(chip, 1);
-			fsl_elbc_run_command(mtd);
-
-			memcpy_fromio(elbc_fcm_ctrl->oob_poi + 6,
-				&elbc_fcm_ctrl->addr[elbc_fcm_ctrl->index], 3);
-			elbc_fcm_ctrl->index += 3;
-		}
-
-		elbc_fcm_ctrl->oob_poi = NULL;
 		return;
 	}
 
@@ -752,13 +747,8 @@ static void fsl_elbc_write_page(struct mtd_info *mtd,
                                 struct nand_chip *chip,
                                 const uint8_t *buf)
 {
-	struct fsl_elbc_mtd *priv = chip->priv;
-	struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl = priv->ctrl->nand;
-
 	fsl_elbc_write_buf(mtd, buf, mtd->writesize);
 	fsl_elbc_write_buf(mtd, chip->oob_poi, mtd->oobsize);
-
-	elbc_fcm_ctrl->oob_poi = chip->oob_poi;
 }
 
 static int fsl_elbc_chip_init(struct fsl_elbc_mtd *priv)
@@ -791,8 +781,8 @@ static int fsl_elbc_chip_init(struct fsl_elbc_mtd *priv)
 	chip->bbt_md = &bbt_mirror_descr;
 
 	/* set up nand options */
-	chip->options = NAND_NO_READRDY | NAND_NO_AUTOINCR |
-			NAND_USE_FLASH_BBT;
+	chip->options = NAND_NO_READRDY | NAND_NO_AUTOINCR;
+	chip->bbt_options = NAND_BBT_USE_FLASH;
 
 	chip->controller = &elbc_fcm_ctrl->controller;
 	chip->priv = priv;
@@ -829,7 +819,6 @@ static int fsl_elbc_chip_remove(struct fsl_elbc_mtd *priv)
 
 	elbc_fcm_ctrl->chips[priv->bank] = NULL;
 	kfree(priv);
-	kfree(elbc_fcm_ctrl);
 	return 0;
 }
 
@@ -842,13 +831,14 @@ static int __devinit fsl_elbc_nand_probe(struct platform_device *pdev)
 	struct resource res;
 	struct fsl_elbc_fcm_ctrl *elbc_fcm_ctrl;
 	static const char *part_probe_types[]
-		= { "cmdlinepart", "RedBoot", NULL };
-	struct mtd_partition *parts;
+		= { "cmdlinepart", "RedBoot", "ofpart", NULL };
 	int ret;
 	int bank;
 	struct device *dev;
 	struct device_node *node = pdev->dev.of_node;
+	struct mtd_part_parser_data ppdata;
 
+	ppdata.of_node = pdev->dev.of_node;
 	if (!fsl_lbc_ctrl_dev || !fsl_lbc_ctrl_dev->regs)
 		return -ENODEV;
 	lbc = fsl_lbc_ctrl_dev->regs;
@@ -934,17 +924,8 @@ static int __devinit fsl_elbc_nand_probe(struct platform_device *pdev)
 
 	/* First look for RedBoot table or partitions on the command
 	 * line, these take precedence over device tree information */
-	ret = parse_mtd_partitions(&priv->mtd, part_probe_types, &parts, 0);
-	if (ret < 0)
-		goto err;
-
-	if (ret == 0) {
-		ret = of_mtd_parse_partitions(priv->dev, node, &parts);
-		if (ret < 0)
-			goto err;
-	}
-
-	mtd_device_register(&priv->mtd, parts, ret);
+	mtd_device_parse_register(&priv->mtd, part_probe_types, &ppdata,
+				  NULL, 0);
 
 	printk(KERN_INFO "eLBC NAND device at 0x%llx, bank %d\n",
 	       (unsigned long long)res.start, priv->bank);
diff --git a/drivers/mtd/nand/fsl_upm.c b/drivers/mtd/nand/fsl_upm.c
index 23752fd5bc59..b4f3cc9f32fb 100644
--- a/drivers/mtd/nand/fsl_upm.c
+++ b/drivers/mtd/nand/fsl_upm.c
@@ -158,7 +158,7 @@ static int __devinit fun_chip_init(struct fsl_upm_nand *fun,
 {
 	int ret;
 	struct device_node *flash_np;
-	static const char *part_types[] = { "cmdlinepart", NULL, };
+	struct mtd_part_parser_data ppdata;
 
 	fun->chip.IO_ADDR_R = fun->io_base;
 	fun->chip.IO_ADDR_W = fun->io_base;
@@ -192,18 +192,12 @@ static int __devinit fun_chip_init(struct fsl_upm_nand *fun,
 	if (ret)
 		goto err;
 
-	ret = parse_mtd_partitions(&fun->mtd, part_types, &fun->parts, 0);
-
-#ifdef CONFIG_MTD_OF_PARTS
-	if (ret == 0) {
-		ret = of_mtd_parse_partitions(fun->dev, flash_np, &fun->parts);
-		if (ret < 0)
-			goto err;
-	}
-#endif
-	ret = mtd_device_register(&fun->mtd, fun->parts, ret);
+	ppdata.of_node = flash_np;
+	ret = mtd_device_parse_register(&fun->mtd, NULL, &ppdata, NULL, 0);
 err:
 	of_node_put(flash_np);
+	if (ret)
+		kfree(fun->mtd.name);
 	return ret;
 }
 
diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c
index e9b275ac381c..e53b76064133 100644
--- a/drivers/mtd/nand/fsmc_nand.c
+++ b/drivers/mtd/nand/fsmc_nand.c
@@ -146,7 +146,7 @@ static struct mtd_partition partition_info_16KB_blk[] = {
 	{
 		.name = "Root File System",
 		.offset = 0x460000,
-		.size = 0,
+		.size = MTDPART_SIZ_FULL,
 	},
 };
 
@@ -173,13 +173,10 @@ static struct mtd_partition partition_info_128KB_blk[] = {
 	{
 		.name = "Root File System",
 		.offset = 0x800000,
-		.size = 0,
+		.size = MTDPART_SIZ_FULL,
 	},
 };
 
-#ifdef CONFIG_MTD_CMDLINE_PARTS
-const char *part_probes[] = { "cmdlinepart", NULL };
-#endif
 
 /**
  * struct fsmc_nand_data - structure for FSMC NAND device state
@@ -187,8 +184,6 @@ const char *part_probes[] = { "cmdlinepart", NULL };
  * @pid:		Part ID on the AMBA PrimeCell format
  * @mtd:		MTD info for a NAND flash.
  * @nand:		Chip related info for a NAND flash.
- * @partitions:		Partition info for a NAND Flash.
- * @nr_partitions:	Total number of partition of a NAND flash.
  *
  * @ecc_place:		ECC placing locations in oobfree type format.
  * @bank:		Bank number for probed device.
@@ -203,8 +198,6 @@ struct fsmc_nand_data {
 	u32			pid;
 	struct mtd_info		mtd;
 	struct nand_chip	nand;
-	struct mtd_partition	*partitions;
-	unsigned int		nr_partitions;
 
 	struct fsmc_eccplace	*ecc_place;
 	unsigned int		bank;
@@ -716,65 +709,17 @@ static int __init fsmc_nand_probe(struct platform_device *pdev)
 	 * platform data,
 	 * default partition information present in driver.
 	 */
-#ifdef CONFIG_MTD_CMDLINE_PARTS
 	/*
-	 * Check if partition info passed via command line
+	 * Check for partition info passed
 	 */
 	host->mtd.name = "nand";
-	host->nr_partitions = parse_mtd_partitions(&host->mtd, part_probes,
-			&host->partitions, 0);
-	if (host->nr_partitions <= 0) {
-#endif
-		/*
-		 * Check if partition info passed via command line
-		 */
-		if (pdata->partitions) {
-			host->partitions = pdata->partitions;
-			host->nr_partitions = pdata->nr_partitions;
-		} else {
-			struct mtd_partition *partition;
-			int i;
-
-			/* Select the default partitions info */
-			switch (host->mtd.size) {
-			case 0x01000000:
-			case 0x02000000:
-			case 0x04000000:
-				host->partitions = partition_info_16KB_blk;
-				host->nr_partitions =
-					sizeof(partition_info_16KB_blk) /
-					sizeof(struct mtd_partition);
-				break;
-			case 0x08000000:
-			case 0x10000000:
-			case 0x20000000:
-			case 0x40000000:
-				host->partitions = partition_info_128KB_blk;
-				host->nr_partitions =
-					sizeof(partition_info_128KB_blk) /
-					sizeof(struct mtd_partition);
-				break;
-			default:
-				ret = -ENXIO;
-				pr_err("Unsupported NAND size\n");
-				goto err_probe;
-			}
-
-			partition = host->partitions;
-			for (i = 0; i < host->nr_partitions; i++, partition++) {
-				if (partition->size == 0) {
-					partition->size = host->mtd.size -
-						partition->offset;
-					break;
-				}
-			}
-		}
-#ifdef CONFIG_MTD_CMDLINE_PARTS
-	}
-#endif
-
-	ret = mtd_device_register(&host->mtd, host->partitions,
-				  host->nr_partitions);
+	ret = mtd_device_parse_register(&host->mtd, NULL, 0,
+			host->mtd.size <= 0x04000000 ?
+				partition_info_16KB_blk :
+				partition_info_128KB_blk,
+			host->mtd.size <= 0x04000000 ?
+				ARRAY_SIZE(partition_info_16KB_blk) :
+				ARRAY_SIZE(partition_info_128KB_blk));
 	if (ret)
 		goto err_probe;
 
@@ -822,7 +767,7 @@ static int fsmc_nand_remove(struct platform_device *pdev)
 	platform_set_drvdata(pdev, NULL);
 
 	if (host) {
-		mtd_device_unregister(&host->mtd);
+		nand_release(&host->mtd);
 		clk_disable(host->clk);
 		clk_put(host->clk);
 
diff --git a/drivers/mtd/nand/gpmi-nand/Makefile b/drivers/mtd/nand/gpmi-nand/Makefile
new file mode 100644
index 000000000000..3a462487c35e
--- /dev/null
+++ b/drivers/mtd/nand/gpmi-nand/Makefile
@@ -0,0 +1,3 @@
+obj-$(CONFIG_MTD_NAND_GPMI_NAND) += gpmi_nand.o
+gpmi_nand-objs += gpmi-nand.o
+gpmi_nand-objs += gpmi-lib.o
diff --git a/drivers/mtd/nand/gpmi-nand/bch-regs.h b/drivers/mtd/nand/gpmi-nand/bch-regs.h
new file mode 100644
index 000000000000..4effb8c579db
--- /dev/null
+++ b/drivers/mtd/nand/gpmi-nand/bch-regs.h
@@ -0,0 +1,84 @@
+/*
+ * Freescale GPMI NAND Flash Driver
+ *
+ * Copyright 2008-2011 Freescale Semiconductor, Inc.
+ * Copyright 2008 Embedded Alley Solutions, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+#ifndef __GPMI_NAND_BCH_REGS_H
+#define __GPMI_NAND_BCH_REGS_H
+
+#define HW_BCH_CTRL				0x00000000
+#define HW_BCH_CTRL_SET				0x00000004
+#define HW_BCH_CTRL_CLR				0x00000008
+#define HW_BCH_CTRL_TOG				0x0000000c
+
+#define BM_BCH_CTRL_COMPLETE_IRQ_EN		(1 << 8)
+#define BM_BCH_CTRL_COMPLETE_IRQ		(1 << 0)
+
+#define HW_BCH_STATUS0				0x00000010
+#define HW_BCH_MODE				0x00000020
+#define HW_BCH_ENCODEPTR			0x00000030
+#define HW_BCH_DATAPTR				0x00000040
+#define HW_BCH_METAPTR				0x00000050
+#define HW_BCH_LAYOUTSELECT			0x00000070
+
+#define HW_BCH_FLASH0LAYOUT0			0x00000080
+
+#define BP_BCH_FLASH0LAYOUT0_NBLOCKS		24
+#define BM_BCH_FLASH0LAYOUT0_NBLOCKS	(0xff << BP_BCH_FLASH0LAYOUT0_NBLOCKS)
+#define BF_BCH_FLASH0LAYOUT0_NBLOCKS(v)		\
+	(((v) << BP_BCH_FLASH0LAYOUT0_NBLOCKS) & BM_BCH_FLASH0LAYOUT0_NBLOCKS)
+
+#define BP_BCH_FLASH0LAYOUT0_META_SIZE		16
+#define BM_BCH_FLASH0LAYOUT0_META_SIZE	(0xff << BP_BCH_FLASH0LAYOUT0_META_SIZE)
+#define BF_BCH_FLASH0LAYOUT0_META_SIZE(v)	\
+	(((v) << BP_BCH_FLASH0LAYOUT0_META_SIZE)\
+					 & BM_BCH_FLASH0LAYOUT0_META_SIZE)
+
+#define BP_BCH_FLASH0LAYOUT0_ECC0		12
+#define BM_BCH_FLASH0LAYOUT0_ECC0	(0xf << BP_BCH_FLASH0LAYOUT0_ECC0)
+#define BF_BCH_FLASH0LAYOUT0_ECC0(v)		\
+	(((v) << BP_BCH_FLASH0LAYOUT0_ECC0) & BM_BCH_FLASH0LAYOUT0_ECC0)
+
+#define BP_BCH_FLASH0LAYOUT0_DATA0_SIZE		0
+#define BM_BCH_FLASH0LAYOUT0_DATA0_SIZE		\
+			(0xfff << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE)
+#define BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(v)	\
+	(((v) << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE)\
+					 & BM_BCH_FLASH0LAYOUT0_DATA0_SIZE)
+
+#define HW_BCH_FLASH0LAYOUT1			0x00000090
+
+#define BP_BCH_FLASH0LAYOUT1_PAGE_SIZE		16
+#define BM_BCH_FLASH0LAYOUT1_PAGE_SIZE		\
+			(0xffff << BP_BCH_FLASH0LAYOUT1_PAGE_SIZE)
+#define BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(v)	\
+	(((v) << BP_BCH_FLASH0LAYOUT1_PAGE_SIZE) \
+					 & BM_BCH_FLASH0LAYOUT1_PAGE_SIZE)
+
+#define BP_BCH_FLASH0LAYOUT1_ECCN		12
+#define BM_BCH_FLASH0LAYOUT1_ECCN	(0xf << BP_BCH_FLASH0LAYOUT1_ECCN)
+#define BF_BCH_FLASH0LAYOUT1_ECCN(v)		\
+	(((v) << BP_BCH_FLASH0LAYOUT1_ECCN) & BM_BCH_FLASH0LAYOUT1_ECCN)
+
+#define BP_BCH_FLASH0LAYOUT1_DATAN_SIZE		0
+#define BM_BCH_FLASH0LAYOUT1_DATAN_SIZE		\
+			(0xfff << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE)
+#define BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(v)	\
+	(((v) << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) \
+					 & BM_BCH_FLASH0LAYOUT1_DATAN_SIZE)
+#endif
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c
new file mode 100644
index 000000000000..de4db7604a3f
--- /dev/null
+++ b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c
@@ -0,0 +1,1057 @@
+/*
+ * Freescale GPMI NAND Flash Driver
+ *
+ * Copyright (C) 2008-2011 Freescale Semiconductor, Inc.
+ * Copyright (C) 2008 Embedded Alley Solutions, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+#include <linux/mtd/gpmi-nand.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <mach/mxs.h>
+
+#include "gpmi-nand.h"
+#include "gpmi-regs.h"
+#include "bch-regs.h"
+
+struct timing_threshod timing_default_threshold = {
+	.max_data_setup_cycles       = (BM_GPMI_TIMING0_DATA_SETUP >>
+						BP_GPMI_TIMING0_DATA_SETUP),
+	.internal_data_setup_in_ns   = 0,
+	.max_sample_delay_factor     = (BM_GPMI_CTRL1_RDN_DELAY >>
+						BP_GPMI_CTRL1_RDN_DELAY),
+	.max_dll_clock_period_in_ns  = 32,
+	.max_dll_delay_in_ns         = 16,
+};
+
+/*
+ * Clear the bit and poll it cleared.  This is usually called with
+ * a reset address and mask being either SFTRST(bit 31) or CLKGATE
+ * (bit 30).
+ */
+static int clear_poll_bit(void __iomem *addr, u32 mask)
+{
+	int timeout = 0x400;
+
+	/* clear the bit */
+	__mxs_clrl(mask, addr);
+
+	/*
+	 * SFTRST needs 3 GPMI clocks to settle, the reference manual
+	 * recommends to wait 1us.
+	 */
+	udelay(1);
+
+	/* poll the bit becoming clear */
+	while ((readl(addr) & mask) && --timeout)
+		/* nothing */;
+
+	return !timeout;
+}
+
+#define MODULE_CLKGATE		(1 << 30)
+#define MODULE_SFTRST		(1 << 31)
+/*
+ * The current mxs_reset_block() will do two things:
+ *  [1] enable the module.
+ *  [2] reset the module.
+ *
+ * In most of the cases, it's ok. But there is a hardware bug in the BCH block.
+ * If you try to soft reset the BCH block, it becomes unusable until
+ * the next hard reset. This case occurs in the NAND boot mode. When the board
+ * boots by NAND, the ROM of the chip will initialize the BCH blocks itself.
+ * So If the driver tries to reset the BCH again, the BCH will not work anymore.
+ * You will see a DMA timeout in this case.
+ *
+ * To avoid this bug, just add a new parameter `just_enable` for
+ * the mxs_reset_block(), and rewrite it here.
+ */
+int gpmi_reset_block(void __iomem *reset_addr, bool just_enable)
+{
+	int ret;
+	int timeout = 0x400;
+
+	/* clear and poll SFTRST */
+	ret = clear_poll_bit(reset_addr, MODULE_SFTRST);
+	if (unlikely(ret))
+		goto error;
+
+	/* clear CLKGATE */
+	__mxs_clrl(MODULE_CLKGATE, reset_addr);
+
+	if (!just_enable) {
+		/* set SFTRST to reset the block */
+		__mxs_setl(MODULE_SFTRST, reset_addr);
+		udelay(1);
+
+		/* poll CLKGATE becoming set */
+		while ((!(readl(reset_addr) & MODULE_CLKGATE)) && --timeout)
+			/* nothing */;
+		if (unlikely(!timeout))
+			goto error;
+	}
+
+	/* clear and poll SFTRST */
+	ret = clear_poll_bit(reset_addr, MODULE_SFTRST);
+	if (unlikely(ret))
+		goto error;
+
+	/* clear and poll CLKGATE */
+	ret = clear_poll_bit(reset_addr, MODULE_CLKGATE);
+	if (unlikely(ret))
+		goto error;
+
+	return 0;
+
+error:
+	pr_err("%s(%p): module reset timeout\n", __func__, reset_addr);
+	return -ETIMEDOUT;
+}
+
+int gpmi_init(struct gpmi_nand_data *this)
+{
+	struct resources *r = &this->resources;
+	int ret;
+
+	ret = clk_enable(r->clock);
+	if (ret)
+		goto err_out;
+	ret = gpmi_reset_block(r->gpmi_regs, false);
+	if (ret)
+		goto err_out;
+
+	/* Choose NAND mode. */
+	writel(BM_GPMI_CTRL1_GPMI_MODE, r->gpmi_regs + HW_GPMI_CTRL1_CLR);
+
+	/* Set the IRQ polarity. */
+	writel(BM_GPMI_CTRL1_ATA_IRQRDY_POLARITY,
+				r->gpmi_regs + HW_GPMI_CTRL1_SET);
+
+	/* Disable Write-Protection. */
+	writel(BM_GPMI_CTRL1_DEV_RESET, r->gpmi_regs + HW_GPMI_CTRL1_SET);
+
+	/* Select BCH ECC. */
+	writel(BM_GPMI_CTRL1_BCH_MODE, r->gpmi_regs + HW_GPMI_CTRL1_SET);
+
+	clk_disable(r->clock);
+	return 0;
+err_out:
+	return ret;
+}
+
+/* This function is very useful. It is called only when the bug occur. */
+void gpmi_dump_info(struct gpmi_nand_data *this)
+{
+	struct resources *r = &this->resources;
+	struct bch_geometry *geo = &this->bch_geometry;
+	u32 reg;
+	int i;
+
+	pr_err("Show GPMI registers :\n");
+	for (i = 0; i <= HW_GPMI_DEBUG / 0x10 + 1; i++) {
+		reg = readl(r->gpmi_regs + i * 0x10);
+		pr_err("offset 0x%.3x : 0x%.8x\n", i * 0x10, reg);
+	}
+
+	/* start to print out the BCH info */
+	pr_err("BCH Geometry :\n");
+	pr_err("GF length              : %u\n", geo->gf_len);
+	pr_err("ECC Strength           : %u\n", geo->ecc_strength);
+	pr_err("Page Size in Bytes     : %u\n", geo->page_size);
+	pr_err("Metadata Size in Bytes : %u\n", geo->metadata_size);
+	pr_err("ECC Chunk Size in Bytes: %u\n", geo->ecc_chunk_size);
+	pr_err("ECC Chunk Count        : %u\n", geo->ecc_chunk_count);
+	pr_err("Payload Size in Bytes  : %u\n", geo->payload_size);
+	pr_err("Auxiliary Size in Bytes: %u\n", geo->auxiliary_size);
+	pr_err("Auxiliary Status Offset: %u\n", geo->auxiliary_status_offset);
+	pr_err("Block Mark Byte Offset : %u\n", geo->block_mark_byte_offset);
+	pr_err("Block Mark Bit Offset  : %u\n", geo->block_mark_bit_offset);
+}
+
+/* Configures the geometry for BCH.  */
+int bch_set_geometry(struct gpmi_nand_data *this)
+{
+	struct resources *r = &this->resources;
+	struct bch_geometry *bch_geo = &this->bch_geometry;
+	unsigned int block_count;
+	unsigned int block_size;
+	unsigned int metadata_size;
+	unsigned int ecc_strength;
+	unsigned int page_size;
+	int ret;
+
+	if (common_nfc_set_geometry(this))
+		return !0;
+
+	block_count   = bch_geo->ecc_chunk_count - 1;
+	block_size    = bch_geo->ecc_chunk_size;
+	metadata_size = bch_geo->metadata_size;
+	ecc_strength  = bch_geo->ecc_strength >> 1;
+	page_size     = bch_geo->page_size;
+
+	ret = clk_enable(r->clock);
+	if (ret)
+		goto err_out;
+
+	ret = gpmi_reset_block(r->bch_regs, true);
+	if (ret)
+		goto err_out;
+
+	/* Configure layout 0. */
+	writel(BF_BCH_FLASH0LAYOUT0_NBLOCKS(block_count)
+			| BF_BCH_FLASH0LAYOUT0_META_SIZE(metadata_size)
+			| BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength)
+			| BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size),
+			r->bch_regs + HW_BCH_FLASH0LAYOUT0);
+
+	writel(BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size)
+			| BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength)
+			| BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size),
+			r->bch_regs + HW_BCH_FLASH0LAYOUT1);
+
+	/* Set *all* chip selects to use layout 0. */
+	writel(0, r->bch_regs + HW_BCH_LAYOUTSELECT);
+
+	/* Enable interrupts. */
+	writel(BM_BCH_CTRL_COMPLETE_IRQ_EN,
+				r->bch_regs + HW_BCH_CTRL_SET);
+
+	clk_disable(r->clock);
+	return 0;
+err_out:
+	return ret;
+}
+
+/* Converts time in nanoseconds to cycles. */
+static unsigned int ns_to_cycles(unsigned int time,
+			unsigned int period, unsigned int min)
+{
+	unsigned int k;
+
+	k = (time + period - 1) / period;
+	return max(k, min);
+}
+
+/* Apply timing to current hardware conditions. */
+static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this,
+					struct gpmi_nfc_hardware_timing *hw)
+{
+	struct gpmi_nand_platform_data *pdata = this->pdata;
+	struct timing_threshod *nfc = &timing_default_threshold;
+	struct nand_chip *nand = &this->nand;
+	struct nand_timing target = this->timing;
+	bool improved_timing_is_available;
+	unsigned long clock_frequency_in_hz;
+	unsigned int clock_period_in_ns;
+	bool dll_use_half_periods;
+	unsigned int dll_delay_shift;
+	unsigned int max_sample_delay_in_ns;
+	unsigned int address_setup_in_cycles;
+	unsigned int data_setup_in_ns;
+	unsigned int data_setup_in_cycles;
+	unsigned int data_hold_in_cycles;
+	int ideal_sample_delay_in_ns;
+	unsigned int sample_delay_factor;
+	int tEYE;
+	unsigned int min_prop_delay_in_ns = pdata->min_prop_delay_in_ns;
+	unsigned int max_prop_delay_in_ns = pdata->max_prop_delay_in_ns;
+
+	/*
+	 * If there are multiple chips, we need to relax the timings to allow
+	 * for signal distortion due to higher capacitance.
+	 */
+	if (nand->numchips > 2) {
+		target.data_setup_in_ns    += 10;
+		target.data_hold_in_ns     += 10;
+		target.address_setup_in_ns += 10;
+	} else if (nand->numchips > 1) {
+		target.data_setup_in_ns    += 5;
+		target.data_hold_in_ns     += 5;
+		target.address_setup_in_ns += 5;
+	}
+
+	/* Check if improved timing information is available. */
+	improved_timing_is_available =
+		(target.tREA_in_ns  >= 0) &&
+		(target.tRLOH_in_ns >= 0) &&
+		(target.tRHOH_in_ns >= 0) ;
+
+	/* Inspect the clock. */
+	clock_frequency_in_hz = nfc->clock_frequency_in_hz;
+	clock_period_in_ns    = 1000000000 / clock_frequency_in_hz;
+
+	/*
+	 * The NFC quantizes setup and hold parameters in terms of clock cycles.
+	 * Here, we quantize the setup and hold timing parameters to the
+	 * next-highest clock period to make sure we apply at least the
+	 * specified times.
+	 *
+	 * For data setup and data hold, the hardware interprets a value of zero
+	 * as the largest possible delay. This is not what's intended by a zero
+	 * in the input parameter, so we impose a minimum of one cycle.
+	 */
+	data_setup_in_cycles    = ns_to_cycles(target.data_setup_in_ns,
+							clock_period_in_ns, 1);
+	data_hold_in_cycles     = ns_to_cycles(target.data_hold_in_ns,
+							clock_period_in_ns, 1);
+	address_setup_in_cycles = ns_to_cycles(target.address_setup_in_ns,
+							clock_period_in_ns, 0);
+
+	/*
+	 * The clock's period affects the sample delay in a number of ways:
+	 *
+	 * (1) The NFC HAL tells us the maximum clock period the sample delay
+	 *     DLL can tolerate. If the clock period is greater than half that
+	 *     maximum, we must configure the DLL to be driven by half periods.
+	 *
+	 * (2) We need to convert from an ideal sample delay, in ns, to a
+	 *     "sample delay factor," which the NFC uses. This factor depends on
+	 *     whether we're driving the DLL with full or half periods.
+	 *     Paraphrasing the reference manual:
+	 *
+	 *         AD = SDF x 0.125 x RP
+	 *
+	 * where:
+	 *
+	 *     AD   is the applied delay, in ns.
+	 *     SDF  is the sample delay factor, which is dimensionless.
+	 *     RP   is the reference period, in ns, which is a full clock period
+	 *          if the DLL is being driven by full periods, or half that if
+	 *          the DLL is being driven by half periods.
+	 *
+	 * Let's re-arrange this in a way that's more useful to us:
+	 *
+	 *                        8
+	 *         SDF  =  AD x ----
+	 *                       RP
+	 *
+	 * The reference period is either the clock period or half that, so this
+	 * is:
+	 *
+	 *                        8       AD x DDF
+	 *         SDF  =  AD x -----  =  --------
+	 *                      f x P        P
+	 *
+	 * where:
+	 *
+	 *       f  is 1 or 1/2, depending on how we're driving the DLL.
+	 *       P  is the clock period.
+	 *     DDF  is the DLL Delay Factor, a dimensionless value that
+	 *          incorporates all the constants in the conversion.
+	 *
+	 * DDF will be either 8 or 16, both of which are powers of two. We can
+	 * reduce the cost of this conversion by using bit shifts instead of
+	 * multiplication or division. Thus:
+	 *
+	 *                 AD << DDS
+	 *         SDF  =  ---------
+	 *                     P
+	 *
+	 *     or
+	 *
+	 *         AD  =  (SDF >> DDS) x P
+	 *
+	 * where:
+	 *
+	 *     DDS  is the DLL Delay Shift, the logarithm to base 2 of the DDF.
+	 */
+	if (clock_period_in_ns > (nfc->max_dll_clock_period_in_ns >> 1)) {
+		dll_use_half_periods = true;
+		dll_delay_shift      = 3 + 1;
+	} else {
+		dll_use_half_periods = false;
+		dll_delay_shift      = 3;
+	}
+
+	/*
+	 * Compute the maximum sample delay the NFC allows, under current
+	 * conditions. If the clock is running too slowly, no sample delay is
+	 * possible.
+	 */
+	if (clock_period_in_ns > nfc->max_dll_clock_period_in_ns)
+		max_sample_delay_in_ns = 0;
+	else {
+		/*
+		 * Compute the delay implied by the largest sample delay factor
+		 * the NFC allows.
+		 */
+		max_sample_delay_in_ns =
+			(nfc->max_sample_delay_factor * clock_period_in_ns) >>
+								dll_delay_shift;
+
+		/*
+		 * Check if the implied sample delay larger than the NFC
+		 * actually allows.
+		 */
+		if (max_sample_delay_in_ns > nfc->max_dll_delay_in_ns)
+			max_sample_delay_in_ns = nfc->max_dll_delay_in_ns;
+	}
+
+	/*
+	 * Check if improved timing information is available. If not, we have to
+	 * use a less-sophisticated algorithm.
+	 */
+	if (!improved_timing_is_available) {
+		/*
+		 * Fold the read setup time required by the NFC into the ideal
+		 * sample delay.
+		 */
+		ideal_sample_delay_in_ns = target.gpmi_sample_delay_in_ns +
+						nfc->internal_data_setup_in_ns;
+
+		/*
+		 * The ideal sample delay may be greater than the maximum
+		 * allowed by the NFC. If so, we can trade off sample delay time
+		 * for more data setup time.
+		 *
+		 * In each iteration of the following loop, we add a cycle to
+		 * the data setup time and subtract a corresponding amount from
+		 * the sample delay until we've satisified the constraints or
+		 * can't do any better.
+		 */
+		while ((ideal_sample_delay_in_ns > max_sample_delay_in_ns) &&
+			(data_setup_in_cycles < nfc->max_data_setup_cycles)) {
+
+			data_setup_in_cycles++;
+			ideal_sample_delay_in_ns -= clock_period_in_ns;
+
+			if (ideal_sample_delay_in_ns < 0)
+				ideal_sample_delay_in_ns = 0;
+
+		}
+
+		/*
+		 * Compute the sample delay factor that corresponds most closely
+		 * to the ideal sample delay. If the result is too large for the
+		 * NFC, use the maximum value.
+		 *
+		 * Notice that we use the ns_to_cycles function to compute the
+		 * sample delay factor. We do this because the form of the
+		 * computation is the same as that for calculating cycles.
+		 */
+		sample_delay_factor =
+			ns_to_cycles(
+				ideal_sample_delay_in_ns << dll_delay_shift,
+							clock_period_in_ns, 0);
+
+		if (sample_delay_factor > nfc->max_sample_delay_factor)
+			sample_delay_factor = nfc->max_sample_delay_factor;
+
+		/* Skip to the part where we return our results. */
+		goto return_results;
+	}
+
+	/*
+	 * If control arrives here, we have more detailed timing information,
+	 * so we can use a better algorithm.
+	 */
+
+	/*
+	 * Fold the read setup time required by the NFC into the maximum
+	 * propagation delay.
+	 */
+	max_prop_delay_in_ns += nfc->internal_data_setup_in_ns;
+
+	/*
+	 * Earlier, we computed the number of clock cycles required to satisfy
+	 * the data setup time. Now, we need to know the actual nanoseconds.
+	 */
+	data_setup_in_ns = clock_period_in_ns * data_setup_in_cycles;
+
+	/*
+	 * Compute tEYE, the width of the data eye when reading from the NAND
+	 * Flash. The eye width is fundamentally determined by the data setup
+	 * time, perturbed by propagation delays and some characteristics of the
+	 * NAND Flash device.
+	 *
+	 * start of the eye = max_prop_delay + tREA
+	 * end of the eye   = min_prop_delay + tRHOH + data_setup
+	 */
+	tEYE = (int)min_prop_delay_in_ns + (int)target.tRHOH_in_ns +
+							(int)data_setup_in_ns;
+
+	tEYE -= (int)max_prop_delay_in_ns + (int)target.tREA_in_ns;
+
+	/*
+	 * The eye must be open. If it's not, we can try to open it by
+	 * increasing its main forcer, the data setup time.
+	 *
+	 * In each iteration of the following loop, we increase the data setup
+	 * time by a single clock cycle. We do this until either the eye is
+	 * open or we run into NFC limits.
+	 */
+	while ((tEYE <= 0) &&
+			(data_setup_in_cycles < nfc->max_data_setup_cycles)) {
+		/* Give a cycle to data setup. */
+		data_setup_in_cycles++;
+		/* Synchronize the data setup time with the cycles. */
+		data_setup_in_ns += clock_period_in_ns;
+		/* Adjust tEYE accordingly. */
+		tEYE += clock_period_in_ns;
+	}
+
+	/*
+	 * When control arrives here, the eye is open. The ideal time to sample
+	 * the data is in the center of the eye:
+	 *
+	 *     end of the eye + start of the eye
+	 *     ---------------------------------  -  data_setup
+	 *                    2
+	 *
+	 * After some algebra, this simplifies to the code immediately below.
+	 */
+	ideal_sample_delay_in_ns =
+		((int)max_prop_delay_in_ns +
+			(int)target.tREA_in_ns +
+				(int)min_prop_delay_in_ns +
+					(int)target.tRHOH_in_ns -
+						(int)data_setup_in_ns) >> 1;
+
+	/*
+	 * The following figure illustrates some aspects of a NAND Flash read:
+	 *
+	 *
+	 *           __                   _____________________________________
+	 * RDN         \_________________/
+	 *
+	 *                                         <---- tEYE ----->
+	 *                                        /-----------------\
+	 * Read Data ----------------------------<                   >---------
+	 *                                        \-----------------/
+	 *             ^                 ^                 ^              ^
+	 *             |                 |                 |              |
+	 *             |<--Data Setup -->|<--Delay Time -->|              |
+	 *             |                 |                 |              |
+	 *             |                 |                                |
+	 *             |                 |<--   Quantized Delay Time   -->|
+	 *             |                 |                                |
+	 *
+	 *
+	 * We have some issues we must now address:
+	 *
+	 * (1) The *ideal* sample delay time must not be negative. If it is, we
+	 *     jam it to zero.
+	 *
+	 * (2) The *ideal* sample delay time must not be greater than that
+	 *     allowed by the NFC. If it is, we can increase the data setup
+	 *     time, which will reduce the delay between the end of the data
+	 *     setup and the center of the eye. It will also make the eye
+	 *     larger, which might help with the next issue...
+	 *
+	 * (3) The *quantized* sample delay time must not fall either before the
+	 *     eye opens or after it closes (the latter is the problem
+	 *     illustrated in the above figure).
+	 */
+
+	/* Jam a negative ideal sample delay to zero. */
+	if (ideal_sample_delay_in_ns < 0)
+		ideal_sample_delay_in_ns = 0;
+
+	/*
+	 * Extend the data setup as needed to reduce the ideal sample delay
+	 * below the maximum permitted by the NFC.
+	 */
+	while ((ideal_sample_delay_in_ns > max_sample_delay_in_ns) &&
+			(data_setup_in_cycles < nfc->max_data_setup_cycles)) {
+
+		/* Give a cycle to data setup. */
+		data_setup_in_cycles++;
+		/* Synchronize the data setup time with the cycles. */
+		data_setup_in_ns += clock_period_in_ns;
+		/* Adjust tEYE accordingly. */
+		tEYE += clock_period_in_ns;
+
+		/*
+		 * Decrease the ideal sample delay by one half cycle, to keep it
+		 * in the middle of the eye.
+		 */
+		ideal_sample_delay_in_ns -= (clock_period_in_ns >> 1);
+
+		/* Jam a negative ideal sample delay to zero. */
+		if (ideal_sample_delay_in_ns < 0)
+			ideal_sample_delay_in_ns = 0;
+	}
+
+	/*
+	 * Compute the sample delay factor that corresponds to the ideal sample
+	 * delay. If the result is too large, then use the maximum allowed
+	 * value.
+	 *
+	 * Notice that we use the ns_to_cycles function to compute the sample
+	 * delay factor. We do this because the form of the computation is the
+	 * same as that for calculating cycles.
+	 */
+	sample_delay_factor =
+		ns_to_cycles(ideal_sample_delay_in_ns << dll_delay_shift,
+							clock_period_in_ns, 0);
+
+	if (sample_delay_factor > nfc->max_sample_delay_factor)
+		sample_delay_factor = nfc->max_sample_delay_factor;
+
+	/*
+	 * These macros conveniently encapsulate a computation we'll use to
+	 * continuously evaluate whether or not the data sample delay is inside
+	 * the eye.
+	 */
+	#define IDEAL_DELAY  ((int) ideal_sample_delay_in_ns)
+
+	#define QUANTIZED_DELAY  \
+		((int) ((sample_delay_factor * clock_period_in_ns) >> \
+							dll_delay_shift))
+
+	#define DELAY_ERROR  (abs(QUANTIZED_DELAY - IDEAL_DELAY))
+
+	#define SAMPLE_IS_NOT_WITHIN_THE_EYE  (DELAY_ERROR > (tEYE >> 1))
+
+	/*
+	 * While the quantized sample time falls outside the eye, reduce the
+	 * sample delay or extend the data setup to move the sampling point back
+	 * toward the eye. Do not allow the number of data setup cycles to
+	 * exceed the maximum allowed by the NFC.
+	 */
+	while (SAMPLE_IS_NOT_WITHIN_THE_EYE &&
+			(data_setup_in_cycles < nfc->max_data_setup_cycles)) {
+		/*
+		 * If control arrives here, the quantized sample delay falls
+		 * outside the eye. Check if it's before the eye opens, or after
+		 * the eye closes.
+		 */
+		if (QUANTIZED_DELAY > IDEAL_DELAY) {
+			/*
+			 * If control arrives here, the quantized sample delay
+			 * falls after the eye closes. Decrease the quantized
+			 * delay time and then go back to re-evaluate.
+			 */
+			if (sample_delay_factor != 0)
+				sample_delay_factor--;
+			continue;
+		}
+
+		/*
+		 * If control arrives here, the quantized sample delay falls
+		 * before the eye opens. Shift the sample point by increasing
+		 * data setup time. This will also make the eye larger.
+		 */
+
+		/* Give a cycle to data setup. */
+		data_setup_in_cycles++;
+		/* Synchronize the data setup time with the cycles. */
+		data_setup_in_ns += clock_period_in_ns;
+		/* Adjust tEYE accordingly. */
+		tEYE += clock_period_in_ns;
+
+		/*
+		 * Decrease the ideal sample delay by one half cycle, to keep it
+		 * in the middle of the eye.
+		 */
+		ideal_sample_delay_in_ns -= (clock_period_in_ns >> 1);
+
+		/* ...and one less period for the delay time. */
+		ideal_sample_delay_in_ns -= clock_period_in_ns;
+
+		/* Jam a negative ideal sample delay to zero. */
+		if (ideal_sample_delay_in_ns < 0)
+			ideal_sample_delay_in_ns = 0;
+
+		/*
+		 * We have a new ideal sample delay, so re-compute the quantized
+		 * delay.
+		 */
+		sample_delay_factor =
+			ns_to_cycles(
+				ideal_sample_delay_in_ns << dll_delay_shift,
+							clock_period_in_ns, 0);
+
+		if (sample_delay_factor > nfc->max_sample_delay_factor)
+			sample_delay_factor = nfc->max_sample_delay_factor;
+	}
+
+	/* Control arrives here when we're ready to return our results. */
+return_results:
+	hw->data_setup_in_cycles    = data_setup_in_cycles;
+	hw->data_hold_in_cycles     = data_hold_in_cycles;
+	hw->address_setup_in_cycles = address_setup_in_cycles;
+	hw->use_half_periods        = dll_use_half_periods;
+	hw->sample_delay_factor     = sample_delay_factor;
+
+	/* Return success. */
+	return 0;
+}
+
+/* Begin the I/O */
+void gpmi_begin(struct gpmi_nand_data *this)
+{
+	struct resources *r = &this->resources;
+	struct timing_threshod *nfc = &timing_default_threshold;
+	unsigned char  *gpmi_regs = r->gpmi_regs;
+	unsigned int   clock_period_in_ns;
+	uint32_t       reg;
+	unsigned int   dll_wait_time_in_us;
+	struct gpmi_nfc_hardware_timing  hw;
+	int ret;
+
+	/* Enable the clock. */
+	ret = clk_enable(r->clock);
+	if (ret) {
+		pr_err("We failed in enable the clk\n");
+		goto err_out;
+	}
+
+	/* set ready/busy timeout */
+	writel(0x500 << BP_GPMI_TIMING1_BUSY_TIMEOUT,
+		gpmi_regs + HW_GPMI_TIMING1);
+
+	/* Get the timing information we need. */
+	nfc->clock_frequency_in_hz = clk_get_rate(r->clock);
+	clock_period_in_ns = 1000000000 / nfc->clock_frequency_in_hz;
+
+	gpmi_nfc_compute_hardware_timing(this, &hw);
+
+	/* Set up all the simple timing parameters. */
+	reg = BF_GPMI_TIMING0_ADDRESS_SETUP(hw.address_setup_in_cycles) |
+		BF_GPMI_TIMING0_DATA_HOLD(hw.data_hold_in_cycles)         |
+		BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles)       ;
+
+	writel(reg, gpmi_regs + HW_GPMI_TIMING0);
+
+	/*
+	 * DLL_ENABLE must be set to 0 when setting RDN_DELAY or HALF_PERIOD.
+	 */
+	writel(BM_GPMI_CTRL1_DLL_ENABLE, gpmi_regs + HW_GPMI_CTRL1_CLR);
+
+	/* Clear out the DLL control fields. */
+	writel(BM_GPMI_CTRL1_RDN_DELAY,   gpmi_regs + HW_GPMI_CTRL1_CLR);
+	writel(BM_GPMI_CTRL1_HALF_PERIOD, gpmi_regs + HW_GPMI_CTRL1_CLR);
+
+	/* If no sample delay is called for, return immediately. */
+	if (!hw.sample_delay_factor)
+		return;
+
+	/* Configure the HALF_PERIOD flag. */
+	if (hw.use_half_periods)
+		writel(BM_GPMI_CTRL1_HALF_PERIOD,
+						gpmi_regs + HW_GPMI_CTRL1_SET);
+
+	/* Set the delay factor. */
+	writel(BF_GPMI_CTRL1_RDN_DELAY(hw.sample_delay_factor),
+						gpmi_regs + HW_GPMI_CTRL1_SET);
+
+	/* Enable the DLL. */
+	writel(BM_GPMI_CTRL1_DLL_ENABLE, gpmi_regs + HW_GPMI_CTRL1_SET);
+
+	/*
+	 * After we enable the GPMI DLL, we have to wait 64 clock cycles before
+	 * we can use the GPMI.
+	 *
+	 * Calculate the amount of time we need to wait, in microseconds.
+	 */
+	dll_wait_time_in_us = (clock_period_in_ns * 64) / 1000;
+
+	if (!dll_wait_time_in_us)
+		dll_wait_time_in_us = 1;
+
+	/* Wait for the DLL to settle. */
+	udelay(dll_wait_time_in_us);
+
+err_out:
+	return;
+}
+
+void gpmi_end(struct gpmi_nand_data *this)
+{
+	struct resources *r = &this->resources;
+	clk_disable(r->clock);
+}
+
+/* Clears a BCH interrupt. */
+void gpmi_clear_bch(struct gpmi_nand_data *this)
+{
+	struct resources *r = &this->resources;
+	writel(BM_BCH_CTRL_COMPLETE_IRQ, r->bch_regs + HW_BCH_CTRL_CLR);
+}
+
+/* Returns the Ready/Busy status of the given chip. */
+int gpmi_is_ready(struct gpmi_nand_data *this, unsigned chip)
+{
+	struct resources *r = &this->resources;
+	uint32_t mask = 0;
+	uint32_t reg = 0;
+
+	if (GPMI_IS_MX23(this)) {
+		mask = MX23_BM_GPMI_DEBUG_READY0 << chip;
+		reg = readl(r->gpmi_regs + HW_GPMI_DEBUG);
+	} else if (GPMI_IS_MX28(this)) {
+		mask = MX28_BF_GPMI_STAT_READY_BUSY(1 << chip);
+		reg = readl(r->gpmi_regs + HW_GPMI_STAT);
+	} else
+		pr_err("unknow arch.\n");
+	return reg & mask;
+}
+
+static inline void set_dma_type(struct gpmi_nand_data *this,
+					enum dma_ops_type type)
+{
+	this->last_dma_type = this->dma_type;
+	this->dma_type = type;
+}
+
+int gpmi_send_command(struct gpmi_nand_data *this)
+{
+	struct dma_chan *channel = get_dma_chan(this);
+	struct dma_async_tx_descriptor *desc;
+	struct scatterlist *sgl;
+	int chip = this->current_chip;
+	u32 pio[3];
+
+	/* [1] send out the PIO words */
+	pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__WRITE)
+		| BM_GPMI_CTRL0_WORD_LENGTH
+		| BF_GPMI_CTRL0_CS(chip, this)
+		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+		| BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_CLE)
+		| BM_GPMI_CTRL0_ADDRESS_INCREMENT
+		| BF_GPMI_CTRL0_XFER_COUNT(this->command_length);
+	pio[1] = pio[2] = 0;
+	desc = channel->device->device_prep_slave_sg(channel,
+					(struct scatterlist *)pio,
+					ARRAY_SIZE(pio), DMA_NONE, 0);
+	if (!desc) {
+		pr_err("step 1 error\n");
+		return -1;
+	}
+
+	/* [2] send out the COMMAND + ADDRESS string stored in @buffer */
+	sgl = &this->cmd_sgl;
+
+	sg_init_one(sgl, this->cmd_buffer, this->command_length);
+	dma_map_sg(this->dev, sgl, 1, DMA_TO_DEVICE);
+	desc = channel->device->device_prep_slave_sg(channel,
+					sgl, 1, DMA_TO_DEVICE, 1);
+	if (!desc) {
+		pr_err("step 2 error\n");
+		return -1;
+	}
+
+	/* [3] submit the DMA */
+	set_dma_type(this, DMA_FOR_COMMAND);
+	return start_dma_without_bch_irq(this, desc);
+}
+
+int gpmi_send_data(struct gpmi_nand_data *this)
+{
+	struct dma_async_tx_descriptor *desc;
+	struct dma_chan *channel = get_dma_chan(this);
+	int chip = this->current_chip;
+	uint32_t command_mode;
+	uint32_t address;
+	u32 pio[2];
+
+	/* [1] PIO */
+	command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WRITE;
+	address      = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
+
+	pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
+		| BM_GPMI_CTRL0_WORD_LENGTH
+		| BF_GPMI_CTRL0_CS(chip, this)
+		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+		| BF_GPMI_CTRL0_ADDRESS(address)
+		| BF_GPMI_CTRL0_XFER_COUNT(this->upper_len);
+	pio[1] = 0;
+	desc = channel->device->device_prep_slave_sg(channel,
+					(struct scatterlist *)pio,
+					ARRAY_SIZE(pio), DMA_NONE, 0);
+	if (!desc) {
+		pr_err("step 1 error\n");
+		return -1;
+	}
+
+	/* [2] send DMA request */
+	prepare_data_dma(this, DMA_TO_DEVICE);
+	desc = channel->device->device_prep_slave_sg(channel, &this->data_sgl,
+						1, DMA_TO_DEVICE, 1);
+	if (!desc) {
+		pr_err("step 2 error\n");
+		return -1;
+	}
+	/* [3] submit the DMA */
+	set_dma_type(this, DMA_FOR_WRITE_DATA);
+	return start_dma_without_bch_irq(this, desc);
+}
+
+int gpmi_read_data(struct gpmi_nand_data *this)
+{
+	struct dma_async_tx_descriptor *desc;
+	struct dma_chan *channel = get_dma_chan(this);
+	int chip = this->current_chip;
+	u32 pio[2];
+
+	/* [1] : send PIO */
+	pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__READ)
+		| BM_GPMI_CTRL0_WORD_LENGTH
+		| BF_GPMI_CTRL0_CS(chip, this)
+		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+		| BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_DATA)
+		| BF_GPMI_CTRL0_XFER_COUNT(this->upper_len);
+	pio[1] = 0;
+	desc = channel->device->device_prep_slave_sg(channel,
+					(struct scatterlist *)pio,
+					ARRAY_SIZE(pio), DMA_NONE, 0);
+	if (!desc) {
+		pr_err("step 1 error\n");
+		return -1;
+	}
+
+	/* [2] : send DMA request */
+	prepare_data_dma(this, DMA_FROM_DEVICE);
+	desc = channel->device->device_prep_slave_sg(channel, &this->data_sgl,
+						1, DMA_FROM_DEVICE, 1);
+	if (!desc) {
+		pr_err("step 2 error\n");
+		return -1;
+	}
+
+	/* [3] : submit the DMA */
+	set_dma_type(this, DMA_FOR_READ_DATA);
+	return start_dma_without_bch_irq(this, desc);
+}
+
+int gpmi_send_page(struct gpmi_nand_data *this,
+			dma_addr_t payload, dma_addr_t auxiliary)
+{
+	struct bch_geometry *geo = &this->bch_geometry;
+	uint32_t command_mode;
+	uint32_t address;
+	uint32_t ecc_command;
+	uint32_t buffer_mask;
+	struct dma_async_tx_descriptor *desc;
+	struct dma_chan *channel = get_dma_chan(this);
+	int chip = this->current_chip;
+	u32 pio[6];
+
+	/* A DMA descriptor that does an ECC page read. */
+	command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WRITE;
+	address      = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
+	ecc_command  = BV_GPMI_ECCCTRL_ECC_CMD__BCH_ENCODE;
+	buffer_mask  = BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE |
+				BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY;
+
+	pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
+		| BM_GPMI_CTRL0_WORD_LENGTH
+		| BF_GPMI_CTRL0_CS(chip, this)
+		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+		| BF_GPMI_CTRL0_ADDRESS(address)
+		| BF_GPMI_CTRL0_XFER_COUNT(0);
+	pio[1] = 0;
+	pio[2] = BM_GPMI_ECCCTRL_ENABLE_ECC
+		| BF_GPMI_ECCCTRL_ECC_CMD(ecc_command)
+		| BF_GPMI_ECCCTRL_BUFFER_MASK(buffer_mask);
+	pio[3] = geo->page_size;
+	pio[4] = payload;
+	pio[5] = auxiliary;
+
+	desc = channel->device->device_prep_slave_sg(channel,
+					(struct scatterlist *)pio,
+					ARRAY_SIZE(pio), DMA_NONE, 0);
+	if (!desc) {
+		pr_err("step 2 error\n");
+		return -1;
+	}
+	set_dma_type(this, DMA_FOR_WRITE_ECC_PAGE);
+	return start_dma_with_bch_irq(this, desc);
+}
+
+int gpmi_read_page(struct gpmi_nand_data *this,
+				dma_addr_t payload, dma_addr_t auxiliary)
+{
+	struct bch_geometry *geo = &this->bch_geometry;
+	uint32_t command_mode;
+	uint32_t address;
+	uint32_t ecc_command;
+	uint32_t buffer_mask;
+	struct dma_async_tx_descriptor *desc;
+	struct dma_chan *channel = get_dma_chan(this);
+	int chip = this->current_chip;
+	u32 pio[6];
+
+	/* [1] Wait for the chip to report ready. */
+	command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY;
+	address      = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
+
+	pio[0] =  BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
+		| BM_GPMI_CTRL0_WORD_LENGTH
+		| BF_GPMI_CTRL0_CS(chip, this)
+		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+		| BF_GPMI_CTRL0_ADDRESS(address)
+		| BF_GPMI_CTRL0_XFER_COUNT(0);
+	pio[1] = 0;
+	desc = channel->device->device_prep_slave_sg(channel,
+				(struct scatterlist *)pio, 2, DMA_NONE, 0);
+	if (!desc) {
+		pr_err("step 1 error\n");
+		return -1;
+	}
+
+	/* [2] Enable the BCH block and read. */
+	command_mode = BV_GPMI_CTRL0_COMMAND_MODE__READ;
+	address      = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
+	ecc_command  = BV_GPMI_ECCCTRL_ECC_CMD__BCH_DECODE;
+	buffer_mask  = BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE
+			| BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY;
+
+	pio[0] =  BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
+		| BM_GPMI_CTRL0_WORD_LENGTH
+		| BF_GPMI_CTRL0_CS(chip, this)
+		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+		| BF_GPMI_CTRL0_ADDRESS(address)
+		| BF_GPMI_CTRL0_XFER_COUNT(geo->page_size);
+
+	pio[1] = 0;
+	pio[2] =  BM_GPMI_ECCCTRL_ENABLE_ECC
+		| BF_GPMI_ECCCTRL_ECC_CMD(ecc_command)
+		| BF_GPMI_ECCCTRL_BUFFER_MASK(buffer_mask);
+	pio[3] = geo->page_size;
+	pio[4] = payload;
+	pio[5] = auxiliary;
+	desc = channel->device->device_prep_slave_sg(channel,
+					(struct scatterlist *)pio,
+					ARRAY_SIZE(pio), DMA_NONE, 1);
+	if (!desc) {
+		pr_err("step 2 error\n");
+		return -1;
+	}
+
+	/* [3] Disable the BCH block */
+	command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY;
+	address      = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
+
+	pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
+		| BM_GPMI_CTRL0_WORD_LENGTH
+		| BF_GPMI_CTRL0_CS(chip, this)
+		| BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+		| BF_GPMI_CTRL0_ADDRESS(address)
+		| BF_GPMI_CTRL0_XFER_COUNT(geo->page_size);
+	pio[1] = 0;
+	desc = channel->device->device_prep_slave_sg(channel,
+				(struct scatterlist *)pio, 2, DMA_NONE, 1);
+	if (!desc) {
+		pr_err("step 3 error\n");
+		return -1;
+	}
+
+	/* [4] submit the DMA */
+	set_dma_type(this, DMA_FOR_READ_ECC_PAGE);
+	return start_dma_with_bch_irq(this, desc);
+}
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
new file mode 100644
index 000000000000..071b63420f0e
--- /dev/null
+++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
@@ -0,0 +1,1619 @@
+/*
+ * Freescale GPMI NAND Flash Driver
+ *
+ * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
+ * Copyright (C) 2008 Embedded Alley Solutions, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+#include <linux/clk.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/mtd/gpmi-nand.h>
+#include <linux/mtd/partitions.h>
+
+#include "gpmi-nand.h"
+
+/* add our owner bbt descriptor */
+static uint8_t scan_ff_pattern[] = { 0xff };
+static struct nand_bbt_descr gpmi_bbt_descr = {
+	.options	= 0,
+	.offs		= 0,
+	.len		= 1,
+	.pattern	= scan_ff_pattern
+};
+
+/*  We will use all the (page + OOB). */
+static struct nand_ecclayout gpmi_hw_ecclayout = {
+	.eccbytes = 0,
+	.eccpos = { 0, },
+	.oobfree = { {.offset = 0, .length = 0} }
+};
+
+static irqreturn_t bch_irq(int irq, void *cookie)
+{
+	struct gpmi_nand_data *this = cookie;
+
+	gpmi_clear_bch(this);
+	complete(&this->bch_done);
+	return IRQ_HANDLED;
+}
+
+/*
+ *  Calculate the ECC strength by hand:
+ *	E : The ECC strength.
+ *	G : the length of Galois Field.
+ *	N : The chunk count of per page.
+ *	O : the oobsize of the NAND chip.
+ *	M : the metasize of per page.
+ *
+ *	The formula is :
+ *		E * G * N
+ *	      ------------ <= (O - M)
+ *                  8
+ *
+ *      So, we get E by:
+ *                    (O - M) * 8
+ *              E <= -------------
+ *                       G * N
+ */
+static inline int get_ecc_strength(struct gpmi_nand_data *this)
+{
+	struct bch_geometry *geo = &this->bch_geometry;
+	struct mtd_info	*mtd = &this->mtd;
+	int ecc_strength;
+
+	ecc_strength = ((mtd->oobsize - geo->metadata_size) * 8)
+			/ (geo->gf_len * geo->ecc_chunk_count);
+
+	/* We need the minor even number. */
+	return round_down(ecc_strength, 2);
+}
+
+int common_nfc_set_geometry(struct gpmi_nand_data *this)
+{
+	struct bch_geometry *geo = &this->bch_geometry;
+	struct mtd_info *mtd = &this->mtd;
+	unsigned int metadata_size;
+	unsigned int status_size;
+	unsigned int block_mark_bit_offset;
+
+	/*
+	 * The size of the metadata can be changed, though we set it to 10
+	 * bytes now. But it can't be too large, because we have to save
+	 * enough space for BCH.
+	 */
+	geo->metadata_size = 10;
+
+	/* The default for the length of Galois Field. */
+	geo->gf_len = 13;
+
+	/* The default for chunk size. There is no oobsize greater then 512. */
+	geo->ecc_chunk_size = 512;
+	while (geo->ecc_chunk_size < mtd->oobsize)
+		geo->ecc_chunk_size *= 2; /* keep C >= O */
+
+	geo->ecc_chunk_count = mtd->writesize / geo->ecc_chunk_size;
+
+	/* We use the same ECC strength for all chunks. */
+	geo->ecc_strength = get_ecc_strength(this);
+	if (!geo->ecc_strength) {
+		pr_err("We get a wrong ECC strength.\n");
+		return -EINVAL;
+	}
+
+	geo->page_size = mtd->writesize + mtd->oobsize;
+	geo->payload_size = mtd->writesize;
+
+	/*
+	 * The auxiliary buffer contains the metadata and the ECC status. The
+	 * metadata is padded to the nearest 32-bit boundary. The ECC status
+	 * contains one byte for every ECC chunk, and is also padded to the
+	 * nearest 32-bit boundary.
+	 */
+	metadata_size = ALIGN(geo->metadata_size, 4);
+	status_size   = ALIGN(geo->ecc_chunk_count, 4);
+
+	geo->auxiliary_size = metadata_size + status_size;
+	geo->auxiliary_status_offset = metadata_size;
+
+	if (!this->swap_block_mark)
+		return 0;
+
+	/*
+	 * We need to compute the byte and bit offsets of
+	 * the physical block mark within the ECC-based view of the page.
+	 *
+	 * NAND chip with 2K page shows below:
+	 *                                             (Block Mark)
+	 *                                                   |      |
+	 *                                                   |  D   |
+	 *                                                   |<---->|
+	 *                                                   V      V
+	 *    +---+----------+-+----------+-+----------+-+----------+-+
+	 *    | M |   data   |E|   data   |E|   data   |E|   data   |E|
+	 *    +---+----------+-+----------+-+----------+-+----------+-+
+	 *
+	 * The position of block mark moves forward in the ECC-based view
+	 * of page, and the delta is:
+	 *
+	 *                   E * G * (N - 1)
+	 *             D = (---------------- + M)
+	 *                          8
+	 *
+	 * With the formula to compute the ECC strength, and the condition
+	 *       : C >= O         (C is the ecc chunk size)
+	 *
+	 * It's easy to deduce to the following result:
+	 *
+	 *         E * G       (O - M)      C - M         C - M
+	 *      ----------- <= ------- <=  --------  <  ---------
+	 *           8            N           N          (N - 1)
+	 *
+	 *  So, we get:
+	 *
+	 *                   E * G * (N - 1)
+	 *             D = (---------------- + M) < C
+	 *                          8
+	 *
+	 *  The above inequality means the position of block mark
+	 *  within the ECC-based view of the page is still in the data chunk,
+	 *  and it's NOT in the ECC bits of the chunk.
+	 *
+	 *  Use the following to compute the bit position of the
+	 *  physical block mark within the ECC-based view of the page:
+	 *          (page_size - D) * 8
+	 *
+	 *  --Huang Shijie
+	 */
+	block_mark_bit_offset = mtd->writesize * 8 -
+		(geo->ecc_strength * geo->gf_len * (geo->ecc_chunk_count - 1)
+				+ geo->metadata_size * 8);
+
+	geo->block_mark_byte_offset = block_mark_bit_offset / 8;
+	geo->block_mark_bit_offset  = block_mark_bit_offset % 8;
+	return 0;
+}
+
+struct dma_chan *get_dma_chan(struct gpmi_nand_data *this)
+{
+	int chipnr = this->current_chip;
+
+	return this->dma_chans[chipnr];
+}
+
+/* Can we use the upper's buffer directly for DMA? */
+void prepare_data_dma(struct gpmi_nand_data *this, enum dma_data_direction dr)
+{
+	struct scatterlist *sgl = &this->data_sgl;
+	int ret;
+
+	this->direct_dma_map_ok = true;
+
+	/* first try to map the upper buffer directly */
+	sg_init_one(sgl, this->upper_buf, this->upper_len);
+	ret = dma_map_sg(this->dev, sgl, 1, dr);
+	if (ret == 0) {
+		/* We have to use our own DMA buffer. */
+		sg_init_one(sgl, this->data_buffer_dma, PAGE_SIZE);
+
+		if (dr == DMA_TO_DEVICE)
+			memcpy(this->data_buffer_dma, this->upper_buf,
+				this->upper_len);
+
+		ret = dma_map_sg(this->dev, sgl, 1, dr);
+		if (ret == 0)
+			pr_err("map failed.\n");
+
+		this->direct_dma_map_ok = false;
+	}
+}
+
+/* This will be called after the DMA operation is finished. */
+static void dma_irq_callback(void *param)
+{
+	struct gpmi_nand_data *this = param;
+	struct completion *dma_c = &this->dma_done;
+
+	complete(dma_c);
+
+	switch (this->dma_type) {
+	case DMA_FOR_COMMAND:
+		dma_unmap_sg(this->dev, &this->cmd_sgl, 1, DMA_TO_DEVICE);
+		break;
+
+	case DMA_FOR_READ_DATA:
+		dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_FROM_DEVICE);
+		if (this->direct_dma_map_ok == false)
+			memcpy(this->upper_buf, this->data_buffer_dma,
+				this->upper_len);
+		break;
+
+	case DMA_FOR_WRITE_DATA:
+		dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_TO_DEVICE);
+		break;
+
+	case DMA_FOR_READ_ECC_PAGE:
+	case DMA_FOR_WRITE_ECC_PAGE:
+		/* We have to wait the BCH interrupt to finish. */
+		break;
+
+	default:
+		pr_err("in wrong DMA operation.\n");
+	}
+}
+
+int start_dma_without_bch_irq(struct gpmi_nand_data *this,
+				struct dma_async_tx_descriptor *desc)
+{
+	struct completion *dma_c = &this->dma_done;
+	int err;
+
+	init_completion(dma_c);
+
+	desc->callback		= dma_irq_callback;
+	desc->callback_param	= this;
+	dmaengine_submit(desc);
+
+	/* Wait for the interrupt from the DMA block. */
+	err = wait_for_completion_timeout(dma_c, msecs_to_jiffies(1000));
+	if (!err) {
+		pr_err("DMA timeout, last DMA :%d\n", this->last_dma_type);
+		gpmi_dump_info(this);
+		return -ETIMEDOUT;
+	}
+	return 0;
+}
+
+/*
+ * This function is used in BCH reading or BCH writing pages.
+ * It will wait for the BCH interrupt as long as ONE second.
+ * Actually, we must wait for two interrupts :
+ *	[1] firstly the DMA interrupt and
+ *	[2] secondly the BCH interrupt.
+ */
+int start_dma_with_bch_irq(struct gpmi_nand_data *this,
+			struct dma_async_tx_descriptor *desc)
+{
+	struct completion *bch_c = &this->bch_done;
+	int err;
+
+	/* Prepare to receive an interrupt from the BCH block. */
+	init_completion(bch_c);
+
+	/* start the DMA */
+	start_dma_without_bch_irq(this, desc);
+
+	/* Wait for the interrupt from the BCH block. */
+	err = wait_for_completion_timeout(bch_c, msecs_to_jiffies(1000));
+	if (!err) {
+		pr_err("BCH timeout, last DMA :%d\n", this->last_dma_type);
+		gpmi_dump_info(this);
+		return -ETIMEDOUT;
+	}
+	return 0;
+}
+
+static int __devinit
+acquire_register_block(struct gpmi_nand_data *this, const char *res_name)
+{
+	struct platform_device *pdev = this->pdev;
+	struct resources *res = &this->resources;
+	struct resource *r;
+	void *p;
+
+	r = platform_get_resource_byname(pdev, IORESOURCE_MEM, res_name);
+	if (!r) {
+		pr_err("Can't get resource for %s\n", res_name);
+		return -ENXIO;
+	}
+
+	p = ioremap(r->start, resource_size(r));
+	if (!p) {
+		pr_err("Can't remap %s\n", res_name);
+		return -ENOMEM;
+	}
+
+	if (!strcmp(res_name, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME))
+		res->gpmi_regs = p;
+	else if (!strcmp(res_name, GPMI_NAND_BCH_REGS_ADDR_RES_NAME))
+		res->bch_regs = p;
+	else
+		pr_err("unknown resource name : %s\n", res_name);
+
+	return 0;
+}
+
+static void release_register_block(struct gpmi_nand_data *this)
+{
+	struct resources *res = &this->resources;
+	if (res->gpmi_regs)
+		iounmap(res->gpmi_regs);
+	if (res->bch_regs)
+		iounmap(res->bch_regs);
+	res->gpmi_regs = NULL;
+	res->bch_regs = NULL;
+}
+
+static int __devinit
+acquire_bch_irq(struct gpmi_nand_data *this, irq_handler_t irq_h)
+{
+	struct platform_device *pdev = this->pdev;
+	struct resources *res = &this->resources;
+	const char *res_name = GPMI_NAND_BCH_INTERRUPT_RES_NAME;
+	struct resource *r;
+	int err;
+
+	r = platform_get_resource_byname(pdev, IORESOURCE_IRQ, res_name);
+	if (!r) {
+		pr_err("Can't get resource for %s\n", res_name);
+		return -ENXIO;
+	}
+
+	err = request_irq(r->start, irq_h, 0, res_name, this);
+	if (err) {
+		pr_err("Can't own %s\n", res_name);
+		return err;
+	}
+
+	res->bch_low_interrupt = r->start;
+	res->bch_high_interrupt = r->end;
+	return 0;
+}
+
+static void release_bch_irq(struct gpmi_nand_data *this)
+{
+	struct resources *res = &this->resources;
+	int i = res->bch_low_interrupt;
+
+	for (; i <= res->bch_high_interrupt; i++)
+		free_irq(i, this);
+}
+
+static bool gpmi_dma_filter(struct dma_chan *chan, void *param)
+{
+	struct gpmi_nand_data *this = param;
+	struct resource *r = this->private;
+
+	if (!mxs_dma_is_apbh(chan))
+		return false;
+	/*
+	 * only catch the GPMI dma channels :
+	 *	for mx23 :	MX23_DMA_GPMI0 ~ MX23_DMA_GPMI3
+	 *		(These four channels share the same IRQ!)
+	 *
+	 *	for mx28 :	MX28_DMA_GPMI0 ~ MX28_DMA_GPMI7
+	 *		(These eight channels share the same IRQ!)
+	 */
+	if (r->start <= chan->chan_id && chan->chan_id <= r->end) {
+		chan->private = &this->dma_data;
+		return true;
+	}
+	return false;
+}
+
+static void release_dma_channels(struct gpmi_nand_data *this)
+{
+	unsigned int i;
+	for (i = 0; i < DMA_CHANS; i++)
+		if (this->dma_chans[i]) {
+			dma_release_channel(this->dma_chans[i]);
+			this->dma_chans[i] = NULL;
+		}
+}
+
+static int __devinit acquire_dma_channels(struct gpmi_nand_data *this)
+{
+	struct platform_device *pdev = this->pdev;
+	struct gpmi_nand_platform_data *pdata = this->pdata;
+	struct resources *res = &this->resources;
+	struct resource *r, *r_dma;
+	unsigned int i;
+
+	r = platform_get_resource_byname(pdev, IORESOURCE_DMA,
+					GPMI_NAND_DMA_CHANNELS_RES_NAME);
+	r_dma = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
+					GPMI_NAND_DMA_INTERRUPT_RES_NAME);
+	if (!r || !r_dma) {
+		pr_err("Can't get resource for DMA\n");
+		return -ENXIO;
+	}
+
+	/* used in gpmi_dma_filter() */
+	this->private = r;
+
+	for (i = r->start; i <= r->end; i++) {
+		struct dma_chan *dma_chan;
+		dma_cap_mask_t mask;
+
+		if (i - r->start >= pdata->max_chip_count)
+			break;
+
+		dma_cap_zero(mask);
+		dma_cap_set(DMA_SLAVE, mask);
+
+		/* get the DMA interrupt */
+		if (r_dma->start == r_dma->end) {
+			/* only register the first. */
+			if (i == r->start)
+				this->dma_data.chan_irq = r_dma->start;
+			else
+				this->dma_data.chan_irq = NO_IRQ;
+		} else
+			this->dma_data.chan_irq = r_dma->start + (i - r->start);
+
+		dma_chan = dma_request_channel(mask, gpmi_dma_filter, this);
+		if (!dma_chan)
+			goto acquire_err;
+
+		/* fill the first empty item */
+		this->dma_chans[i - r->start] = dma_chan;
+	}
+
+	res->dma_low_channel = r->start;
+	res->dma_high_channel = i;
+	return 0;
+
+acquire_err:
+	pr_err("Can't acquire DMA channel %u\n", i);
+	release_dma_channels(this);
+	return -EINVAL;
+}
+
+static int __devinit acquire_resources(struct gpmi_nand_data *this)
+{
+	struct resources *res = &this->resources;
+	int ret;
+
+	ret = acquire_register_block(this, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME);
+	if (ret)
+		goto exit_regs;
+
+	ret = acquire_register_block(this, GPMI_NAND_BCH_REGS_ADDR_RES_NAME);
+	if (ret)
+		goto exit_regs;
+
+	ret = acquire_bch_irq(this, bch_irq);
+	if (ret)
+		goto exit_regs;
+
+	ret = acquire_dma_channels(this);
+	if (ret)
+		goto exit_dma_channels;
+
+	res->clock = clk_get(&this->pdev->dev, NULL);
+	if (IS_ERR(res->clock)) {
+		pr_err("can not get the clock\n");
+		ret = -ENOENT;
+		goto exit_clock;
+	}
+	return 0;
+
+exit_clock:
+	release_dma_channels(this);
+exit_dma_channels:
+	release_bch_irq(this);
+exit_regs:
+	release_register_block(this);
+	return ret;
+}
+
+static void release_resources(struct gpmi_nand_data *this)
+{
+	struct resources *r = &this->resources;
+
+	clk_put(r->clock);
+	release_register_block(this);
+	release_bch_irq(this);
+	release_dma_channels(this);
+}
+
+static int __devinit init_hardware(struct gpmi_nand_data *this)
+{
+	int ret;
+
+	/*
+	 * This structure contains the "safe" GPMI timing that should succeed
+	 * with any NAND Flash device
+	 * (although, with less-than-optimal performance).
+	 */
+	struct nand_timing  safe_timing = {
+		.data_setup_in_ns        = 80,
+		.data_hold_in_ns         = 60,
+		.address_setup_in_ns     = 25,
+		.gpmi_sample_delay_in_ns =  6,
+		.tREA_in_ns              = -1,
+		.tRLOH_in_ns             = -1,
+		.tRHOH_in_ns             = -1,
+	};
+
+	/* Initialize the hardwares. */
+	ret = gpmi_init(this);
+	if (ret)
+		return ret;
+
+	this->timing = safe_timing;
+	return 0;
+}
+
+static int read_page_prepare(struct gpmi_nand_data *this,
+			void *destination, unsigned length,
+			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
+			void **use_virt, dma_addr_t *use_phys)
+{
+	struct device *dev = this->dev;
+
+	if (virt_addr_valid(destination)) {
+		dma_addr_t dest_phys;
+
+		dest_phys = dma_map_single(dev, destination,
+						length, DMA_FROM_DEVICE);
+		if (dma_mapping_error(dev, dest_phys)) {
+			if (alt_size < length) {
+				pr_err("Alternate buffer is too small\n");
+				return -ENOMEM;
+			}
+			goto map_failed;
+		}
+		*use_virt = destination;
+		*use_phys = dest_phys;
+		this->direct_dma_map_ok = true;
+		return 0;
+	}
+
+map_failed:
+	*use_virt = alt_virt;
+	*use_phys = alt_phys;
+	this->direct_dma_map_ok = false;
+	return 0;
+}
+
+static inline void read_page_end(struct gpmi_nand_data *this,
+			void *destination, unsigned length,
+			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
+			void *used_virt, dma_addr_t used_phys)
+{
+	if (this->direct_dma_map_ok)
+		dma_unmap_single(this->dev, used_phys, length, DMA_FROM_DEVICE);
+}
+
+static inline void read_page_swap_end(struct gpmi_nand_data *this,
+			void *destination, unsigned length,
+			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
+			void *used_virt, dma_addr_t used_phys)
+{
+	if (!this->direct_dma_map_ok)
+		memcpy(destination, alt_virt, length);
+}
+
+static int send_page_prepare(struct gpmi_nand_data *this,
+			const void *source, unsigned length,
+			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
+			const void **use_virt, dma_addr_t *use_phys)
+{
+	struct device *dev = this->dev;
+
+	if (virt_addr_valid(source)) {
+		dma_addr_t source_phys;
+
+		source_phys = dma_map_single(dev, (void *)source, length,
+						DMA_TO_DEVICE);
+		if (dma_mapping_error(dev, source_phys)) {
+			if (alt_size < length) {
+				pr_err("Alternate buffer is too small\n");
+				return -ENOMEM;
+			}
+			goto map_failed;
+		}
+		*use_virt = source;
+		*use_phys = source_phys;
+		return 0;
+	}
+map_failed:
+	/*
+	 * Copy the content of the source buffer into the alternate
+	 * buffer and set up the return values accordingly.
+	 */
+	memcpy(alt_virt, source, length);
+
+	*use_virt = alt_virt;
+	*use_phys = alt_phys;
+	return 0;
+}
+
+static void send_page_end(struct gpmi_nand_data *this,
+			const void *source, unsigned length,
+			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
+			const void *used_virt, dma_addr_t used_phys)
+{
+	struct device *dev = this->dev;
+	if (used_virt == source)
+		dma_unmap_single(dev, used_phys, length, DMA_TO_DEVICE);
+}
+
+static void gpmi_free_dma_buffer(struct gpmi_nand_data *this)
+{
+	struct device *dev = this->dev;
+
+	if (this->page_buffer_virt && virt_addr_valid(this->page_buffer_virt))
+		dma_free_coherent(dev, this->page_buffer_size,
+					this->page_buffer_virt,
+					this->page_buffer_phys);
+	kfree(this->cmd_buffer);
+	kfree(this->data_buffer_dma);
+
+	this->cmd_buffer	= NULL;
+	this->data_buffer_dma	= NULL;
+	this->page_buffer_virt	= NULL;
+	this->page_buffer_size	=  0;
+}
+
+/* Allocate the DMA buffers */
+static int gpmi_alloc_dma_buffer(struct gpmi_nand_data *this)
+{
+	struct bch_geometry *geo = &this->bch_geometry;
+	struct device *dev = this->dev;
+
+	/* [1] Allocate a command buffer. PAGE_SIZE is enough. */
+	this->cmd_buffer = kzalloc(PAGE_SIZE, GFP_DMA);
+	if (this->cmd_buffer == NULL)
+		goto error_alloc;
+
+	/* [2] Allocate a read/write data buffer. PAGE_SIZE is enough. */
+	this->data_buffer_dma = kzalloc(PAGE_SIZE, GFP_DMA);
+	if (this->data_buffer_dma == NULL)
+		goto error_alloc;
+
+	/*
+	 * [3] Allocate the page buffer.
+	 *
+	 * Both the payload buffer and the auxiliary buffer must appear on
+	 * 32-bit boundaries. We presume the size of the payload buffer is a
+	 * power of two and is much larger than four, which guarantees the
+	 * auxiliary buffer will appear on a 32-bit boundary.
+	 */
+	this->page_buffer_size = geo->payload_size + geo->auxiliary_size;
+	this->page_buffer_virt = dma_alloc_coherent(dev, this->page_buffer_size,
+					&this->page_buffer_phys, GFP_DMA);
+	if (!this->page_buffer_virt)
+		goto error_alloc;
+
+
+	/* Slice up the page buffer. */
+	this->payload_virt = this->page_buffer_virt;
+	this->payload_phys = this->page_buffer_phys;
+	this->auxiliary_virt = this->payload_virt + geo->payload_size;
+	this->auxiliary_phys = this->payload_phys + geo->payload_size;
+	return 0;
+
+error_alloc:
+	gpmi_free_dma_buffer(this);
+	pr_err("allocate DMA buffer ret!!\n");
+	return -ENOMEM;
+}
+
+static void gpmi_cmd_ctrl(struct mtd_info *mtd, int data, unsigned int ctrl)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+	int ret;
+
+	/*
+	 * Every operation begins with a command byte and a series of zero or
+	 * more address bytes. These are distinguished by either the Address
+	 * Latch Enable (ALE) or Command Latch Enable (CLE) signals being
+	 * asserted. When MTD is ready to execute the command, it will deassert
+	 * both latch enables.
+	 *
+	 * Rather than run a separate DMA operation for every single byte, we
+	 * queue them up and run a single DMA operation for the entire series
+	 * of command and data bytes. NAND_CMD_NONE means the END of the queue.
+	 */
+	if ((ctrl & (NAND_ALE | NAND_CLE))) {
+		if (data != NAND_CMD_NONE)
+			this->cmd_buffer[this->command_length++] = data;
+		return;
+	}
+
+	if (!this->command_length)
+		return;
+
+	ret = gpmi_send_command(this);
+	if (ret)
+		pr_err("Chip: %u, Error %d\n", this->current_chip, ret);
+
+	this->command_length = 0;
+}
+
+static int gpmi_dev_ready(struct mtd_info *mtd)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+
+	return gpmi_is_ready(this, this->current_chip);
+}
+
+static void gpmi_select_chip(struct mtd_info *mtd, int chipnr)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+
+	if ((this->current_chip < 0) && (chipnr >= 0))
+		gpmi_begin(this);
+	else if ((this->current_chip >= 0) && (chipnr < 0))
+		gpmi_end(this);
+
+	this->current_chip = chipnr;
+}
+
+static void gpmi_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+
+	pr_debug("len is %d\n", len);
+	this->upper_buf	= buf;
+	this->upper_len	= len;
+
+	gpmi_read_data(this);
+}
+
+static void gpmi_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+
+	pr_debug("len is %d\n", len);
+	this->upper_buf	= (uint8_t *)buf;
+	this->upper_len	= len;
+
+	gpmi_send_data(this);
+}
+
+static uint8_t gpmi_read_byte(struct mtd_info *mtd)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+	uint8_t *buf = this->data_buffer_dma;
+
+	gpmi_read_buf(mtd, buf, 1);
+	return buf[0];
+}
+
+/*
+ * Handles block mark swapping.
+ * It can be called in swapping the block mark, or swapping it back,
+ * because the the operations are the same.
+ */
+static void block_mark_swapping(struct gpmi_nand_data *this,
+				void *payload, void *auxiliary)
+{
+	struct bch_geometry *nfc_geo = &this->bch_geometry;
+	unsigned char *p;
+	unsigned char *a;
+	unsigned int  bit;
+	unsigned char mask;
+	unsigned char from_data;
+	unsigned char from_oob;
+
+	if (!this->swap_block_mark)
+		return;
+
+	/*
+	 * If control arrives here, we're swapping. Make some convenience
+	 * variables.
+	 */
+	bit = nfc_geo->block_mark_bit_offset;
+	p   = payload + nfc_geo->block_mark_byte_offset;
+	a   = auxiliary;
+
+	/*
+	 * Get the byte from the data area that overlays the block mark. Since
+	 * the ECC engine applies its own view to the bits in the page, the
+	 * physical block mark won't (in general) appear on a byte boundary in
+	 * the data.
+	 */
+	from_data = (p[0] >> bit) | (p[1] << (8 - bit));
+
+	/* Get the byte from the OOB. */
+	from_oob = a[0];
+
+	/* Swap them. */
+	a[0] = from_data;
+
+	mask = (0x1 << bit) - 1;
+	p[0] = (p[0] & mask) | (from_oob << bit);
+
+	mask = ~0 << bit;
+	p[1] = (p[1] & mask) | (from_oob >> (8 - bit));
+}
+
+static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip,
+				uint8_t *buf, int page)
+{
+	struct gpmi_nand_data *this = chip->priv;
+	struct bch_geometry *nfc_geo = &this->bch_geometry;
+	void          *payload_virt;
+	dma_addr_t    payload_phys;
+	void          *auxiliary_virt;
+	dma_addr_t    auxiliary_phys;
+	unsigned int  i;
+	unsigned char *status;
+	unsigned int  failed;
+	unsigned int  corrected;
+	int           ret;
+
+	pr_debug("page number is : %d\n", page);
+	ret = read_page_prepare(this, buf, mtd->writesize,
+					this->payload_virt, this->payload_phys,
+					nfc_geo->payload_size,
+					&payload_virt, &payload_phys);
+	if (ret) {
+		pr_err("Inadequate DMA buffer\n");
+		ret = -ENOMEM;
+		return ret;
+	}
+	auxiliary_virt = this->auxiliary_virt;
+	auxiliary_phys = this->auxiliary_phys;
+
+	/* go! */
+	ret = gpmi_read_page(this, payload_phys, auxiliary_phys);
+	read_page_end(this, buf, mtd->writesize,
+			this->payload_virt, this->payload_phys,
+			nfc_geo->payload_size,
+			payload_virt, payload_phys);
+	if (ret) {
+		pr_err("Error in ECC-based read: %d\n", ret);
+		goto exit_nfc;
+	}
+
+	/* handle the block mark swapping */
+	block_mark_swapping(this, payload_virt, auxiliary_virt);
+
+	/* Loop over status bytes, accumulating ECC status. */
+	failed		= 0;
+	corrected	= 0;
+	status		= auxiliary_virt + nfc_geo->auxiliary_status_offset;
+
+	for (i = 0; i < nfc_geo->ecc_chunk_count; i++, status++) {
+		if ((*status == STATUS_GOOD) || (*status == STATUS_ERASED))
+			continue;
+
+		if (*status == STATUS_UNCORRECTABLE) {
+			failed++;
+			continue;
+		}
+		corrected += *status;
+	}
+
+	/*
+	 * Propagate ECC status to the owning MTD only when failed or
+	 * corrected times nearly reaches our ECC correction threshold.
+	 */
+	if (failed || corrected >= (nfc_geo->ecc_strength - 1)) {
+		mtd->ecc_stats.failed    += failed;
+		mtd->ecc_stats.corrected += corrected;
+	}
+
+	/*
+	 * It's time to deliver the OOB bytes. See gpmi_ecc_read_oob() for
+	 * details about our policy for delivering the OOB.
+	 *
+	 * We fill the caller's buffer with set bits, and then copy the block
+	 * mark to th caller's buffer. Note that, if block mark swapping was
+	 * necessary, it has already been done, so we can rely on the first
+	 * byte of the auxiliary buffer to contain the block mark.
+	 */
+	memset(chip->oob_poi, ~0, mtd->oobsize);
+	chip->oob_poi[0] = ((uint8_t *) auxiliary_virt)[0];
+
+	read_page_swap_end(this, buf, mtd->writesize,
+			this->payload_virt, this->payload_phys,
+			nfc_geo->payload_size,
+			payload_virt, payload_phys);
+exit_nfc:
+	return ret;
+}
+
+static void gpmi_ecc_write_page(struct mtd_info *mtd,
+				struct nand_chip *chip, const uint8_t *buf)
+{
+	struct gpmi_nand_data *this = chip->priv;
+	struct bch_geometry *nfc_geo = &this->bch_geometry;
+	const void *payload_virt;
+	dma_addr_t payload_phys;
+	const void *auxiliary_virt;
+	dma_addr_t auxiliary_phys;
+	int        ret;
+
+	pr_debug("ecc write page.\n");
+	if (this->swap_block_mark) {
+		/*
+		 * If control arrives here, we're doing block mark swapping.
+		 * Since we can't modify the caller's buffers, we must copy them
+		 * into our own.
+		 */
+		memcpy(this->payload_virt, buf, mtd->writesize);
+		payload_virt = this->payload_virt;
+		payload_phys = this->payload_phys;
+
+		memcpy(this->auxiliary_virt, chip->oob_poi,
+				nfc_geo->auxiliary_size);
+		auxiliary_virt = this->auxiliary_virt;
+		auxiliary_phys = this->auxiliary_phys;
+
+		/* Handle block mark swapping. */
+		block_mark_swapping(this,
+				(void *) payload_virt, (void *) auxiliary_virt);
+	} else {
+		/*
+		 * If control arrives here, we're not doing block mark swapping,
+		 * so we can to try and use the caller's buffers.
+		 */
+		ret = send_page_prepare(this,
+				buf, mtd->writesize,
+				this->payload_virt, this->payload_phys,
+				nfc_geo->payload_size,
+				&payload_virt, &payload_phys);
+		if (ret) {
+			pr_err("Inadequate payload DMA buffer\n");
+			return;
+		}
+
+		ret = send_page_prepare(this,
+				chip->oob_poi, mtd->oobsize,
+				this->auxiliary_virt, this->auxiliary_phys,
+				nfc_geo->auxiliary_size,
+				&auxiliary_virt, &auxiliary_phys);
+		if (ret) {
+			pr_err("Inadequate auxiliary DMA buffer\n");
+			goto exit_auxiliary;
+		}
+	}
+
+	/* Ask the NFC. */
+	ret = gpmi_send_page(this, payload_phys, auxiliary_phys);
+	if (ret)
+		pr_err("Error in ECC-based write: %d\n", ret);
+
+	if (!this->swap_block_mark) {
+		send_page_end(this, chip->oob_poi, mtd->oobsize,
+				this->auxiliary_virt, this->auxiliary_phys,
+				nfc_geo->auxiliary_size,
+				auxiliary_virt, auxiliary_phys);
+exit_auxiliary:
+		send_page_end(this, buf, mtd->writesize,
+				this->payload_virt, this->payload_phys,
+				nfc_geo->payload_size,
+				payload_virt, payload_phys);
+	}
+}
+
+/*
+ * There are several places in this driver where we have to handle the OOB and
+ * block marks. This is the function where things are the most complicated, so
+ * this is where we try to explain it all. All the other places refer back to
+ * here.
+ *
+ * These are the rules, in order of decreasing importance:
+ *
+ * 1) Nothing the caller does can be allowed to imperil the block mark.
+ *
+ * 2) In read operations, the first byte of the OOB we return must reflect the
+ *    true state of the block mark, no matter where that block mark appears in
+ *    the physical page.
+ *
+ * 3) ECC-based read operations return an OOB full of set bits (since we never
+ *    allow ECC-based writes to the OOB, it doesn't matter what ECC-based reads
+ *    return).
+ *
+ * 4) "Raw" read operations return a direct view of the physical bytes in the
+ *    page, using the conventional definition of which bytes are data and which
+ *    are OOB. This gives the caller a way to see the actual, physical bytes
+ *    in the page, without the distortions applied by our ECC engine.
+ *
+ *
+ * What we do for this specific read operation depends on two questions:
+ *
+ * 1) Are we doing a "raw" read, or an ECC-based read?
+ *
+ * 2) Are we using block mark swapping or transcription?
+ *
+ * There are four cases, illustrated by the following Karnaugh map:
+ *
+ *                    |           Raw           |         ECC-based       |
+ *       -------------+-------------------------+-------------------------+
+ *                    | Read the conventional   |                         |
+ *                    | OOB at the end of the   |                         |
+ *       Swapping     | page and return it. It  |                         |
+ *                    | contains exactly what   |                         |
+ *                    | we want.                | Read the block mark and |
+ *       -------------+-------------------------+ return it in a buffer   |
+ *                    | Read the conventional   | full of set bits.       |
+ *                    | OOB at the end of the   |                         |
+ *                    | page and also the block |                         |
+ *       Transcribing | mark in the metadata.   |                         |
+ *                    | Copy the block mark     |                         |
+ *                    | into the first byte of  |                         |
+ *                    | the OOB.                |                         |
+ *       -------------+-------------------------+-------------------------+
+ *
+ * Note that we break rule #4 in the Transcribing/Raw case because we're not
+ * giving an accurate view of the actual, physical bytes in the page (we're
+ * overwriting the block mark). That's OK because it's more important to follow
+ * rule #2.
+ *
+ * It turns out that knowing whether we want an "ECC-based" or "raw" read is not
+ * easy. When reading a page, for example, the NAND Flash MTD code calls our
+ * ecc.read_page or ecc.read_page_raw function. Thus, the fact that MTD wants an
+ * ECC-based or raw view of the page is implicit in which function it calls
+ * (there is a similar pair of ECC-based/raw functions for writing).
+ *
+ * Since MTD assumes the OOB is not covered by ECC, there is no pair of
+ * ECC-based/raw functions for reading or or writing the OOB. The fact that the
+ * caller wants an ECC-based or raw view of the page is not propagated down to
+ * this driver.
+ */
+static int gpmi_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+				int page, int sndcmd)
+{
+	struct gpmi_nand_data *this = chip->priv;
+
+	pr_debug("page number is %d\n", page);
+	/* clear the OOB buffer */
+	memset(chip->oob_poi, ~0, mtd->oobsize);
+
+	/* Read out the conventional OOB. */
+	chip->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page);
+	chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+	/*
+	 * Now, we want to make sure the block mark is correct. In the
+	 * Swapping/Raw case, we already have it. Otherwise, we need to
+	 * explicitly read it.
+	 */
+	if (!this->swap_block_mark) {
+		/* Read the block mark into the first byte of the OOB buffer. */
+		chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page);
+		chip->oob_poi[0] = chip->read_byte(mtd);
+	}
+
+	/*
+	 * Return true, indicating that the next call to this function must send
+	 * a command.
+	 */
+	return true;
+}
+
+static int
+gpmi_ecc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page)
+{
+	/*
+	 * The BCH will use all the (page + oob).
+	 * Our gpmi_hw_ecclayout can only prohibit the JFFS2 to write the oob.
+	 * But it can not stop some ioctls such MEMWRITEOOB which uses
+	 * MTD_OPS_PLACE_OOB. So We have to implement this function to prohibit
+	 * these ioctls too.
+	 */
+	return -EPERM;
+}
+
+static int gpmi_block_markbad(struct mtd_info *mtd, loff_t ofs)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+	int block, ret = 0;
+	uint8_t *block_mark;
+	int column, page, status, chipnr;
+
+	/* Get block number */
+	block = (int)(ofs >> chip->bbt_erase_shift);
+	if (chip->bbt)
+		chip->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1);
+
+	/* Do we have a flash based bad block table ? */
+	if (chip->options & NAND_BBT_USE_FLASH)
+		ret = nand_update_bbt(mtd, ofs);
+	else {
+		chipnr = (int)(ofs >> chip->chip_shift);
+		chip->select_chip(mtd, chipnr);
+
+		column = this->swap_block_mark ? mtd->writesize : 0;
+
+		/* Write the block mark. */
+		block_mark = this->data_buffer_dma;
+		block_mark[0] = 0; /* bad block marker */
+
+		/* Shift to get page */
+		page = (int)(ofs >> chip->page_shift);
+
+		chip->cmdfunc(mtd, NAND_CMD_SEQIN, column, page);
+		chip->write_buf(mtd, block_mark, 1);
+		chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+
+		status = chip->waitfunc(mtd, chip);
+		if (status & NAND_STATUS_FAIL)
+			ret = -EIO;
+
+		chip->select_chip(mtd, -1);
+	}
+	if (!ret)
+		mtd->ecc_stats.badblocks++;
+
+	return ret;
+}
+
+static int __devinit nand_boot_set_geometry(struct gpmi_nand_data *this)
+{
+	struct boot_rom_geometry *geometry = &this->rom_geometry;
+
+	/*
+	 * Set the boot block stride size.
+	 *
+	 * In principle, we should be reading this from the OTP bits, since
+	 * that's where the ROM is going to get it. In fact, we don't have any
+	 * way to read the OTP bits, so we go with the default and hope for the
+	 * best.
+	 */
+	geometry->stride_size_in_pages = 64;
+
+	/*
+	 * Set the search area stride exponent.
+	 *
+	 * In principle, we should be reading this from the OTP bits, since
+	 * that's where the ROM is going to get it. In fact, we don't have any
+	 * way to read the OTP bits, so we go with the default and hope for the
+	 * best.
+	 */
+	geometry->search_area_stride_exponent = 2;
+	return 0;
+}
+
+static const char  *fingerprint = "STMP";
+static int __devinit mx23_check_transcription_stamp(struct gpmi_nand_data *this)
+{
+	struct boot_rom_geometry *rom_geo = &this->rom_geometry;
+	struct device *dev = this->dev;
+	struct mtd_info *mtd = &this->mtd;
+	struct nand_chip *chip = &this->nand;
+	unsigned int search_area_size_in_strides;
+	unsigned int stride;
+	unsigned int page;
+	loff_t byte;
+	uint8_t *buffer = chip->buffers->databuf;
+	int saved_chip_number;
+	int found_an_ncb_fingerprint = false;
+
+	/* Compute the number of strides in a search area. */
+	search_area_size_in_strides = 1 << rom_geo->search_area_stride_exponent;
+
+	saved_chip_number = this->current_chip;
+	chip->select_chip(mtd, 0);
+
+	/*
+	 * Loop through the first search area, looking for the NCB fingerprint.
+	 */
+	dev_dbg(dev, "Scanning for an NCB fingerprint...\n");
+
+	for (stride = 0; stride < search_area_size_in_strides; stride++) {
+		/* Compute the page and byte addresses. */
+		page = stride * rom_geo->stride_size_in_pages;
+		byte = page   * mtd->writesize;
+
+		dev_dbg(dev, "Looking for a fingerprint in page 0x%x\n", page);
+
+		/*
+		 * Read the NCB fingerprint. The fingerprint is four bytes long
+		 * and starts in the 12th byte of the page.
+		 */
+		chip->cmdfunc(mtd, NAND_CMD_READ0, 12, page);
+		chip->read_buf(mtd, buffer, strlen(fingerprint));
+
+		/* Look for the fingerprint. */
+		if (!memcmp(buffer, fingerprint, strlen(fingerprint))) {
+			found_an_ncb_fingerprint = true;
+			break;
+		}
+
+	}
+
+	chip->select_chip(mtd, saved_chip_number);
+
+	if (found_an_ncb_fingerprint)
+		dev_dbg(dev, "\tFound a fingerprint\n");
+	else
+		dev_dbg(dev, "\tNo fingerprint found\n");
+	return found_an_ncb_fingerprint;
+}
+
+/* Writes a transcription stamp. */
+static int __devinit mx23_write_transcription_stamp(struct gpmi_nand_data *this)
+{
+	struct device *dev = this->dev;
+	struct boot_rom_geometry *rom_geo = &this->rom_geometry;
+	struct mtd_info *mtd = &this->mtd;
+	struct nand_chip *chip = &this->nand;
+	unsigned int block_size_in_pages;
+	unsigned int search_area_size_in_strides;
+	unsigned int search_area_size_in_pages;
+	unsigned int search_area_size_in_blocks;
+	unsigned int block;
+	unsigned int stride;
+	unsigned int page;
+	loff_t       byte;
+	uint8_t      *buffer = chip->buffers->databuf;
+	int saved_chip_number;
+	int status;
+
+	/* Compute the search area geometry. */
+	block_size_in_pages = mtd->erasesize / mtd->writesize;
+	search_area_size_in_strides = 1 << rom_geo->search_area_stride_exponent;
+	search_area_size_in_pages = search_area_size_in_strides *
+					rom_geo->stride_size_in_pages;
+	search_area_size_in_blocks =
+		  (search_area_size_in_pages + (block_size_in_pages - 1)) /
+				    block_size_in_pages;
+
+	dev_dbg(dev, "Search Area Geometry :\n");
+	dev_dbg(dev, "\tin Blocks : %u\n", search_area_size_in_blocks);
+	dev_dbg(dev, "\tin Strides: %u\n", search_area_size_in_strides);
+	dev_dbg(dev, "\tin Pages  : %u\n", search_area_size_in_pages);
+
+	/* Select chip 0. */
+	saved_chip_number = this->current_chip;
+	chip->select_chip(mtd, 0);
+
+	/* Loop over blocks in the first search area, erasing them. */
+	dev_dbg(dev, "Erasing the search area...\n");
+
+	for (block = 0; block < search_area_size_in_blocks; block++) {
+		/* Compute the page address. */
+		page = block * block_size_in_pages;
+
+		/* Erase this block. */
+		dev_dbg(dev, "\tErasing block 0x%x\n", block);
+		chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page);
+		chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1);
+
+		/* Wait for the erase to finish. */
+		status = chip->waitfunc(mtd, chip);
+		if (status & NAND_STATUS_FAIL)
+			dev_err(dev, "[%s] Erase failed.\n", __func__);
+	}
+
+	/* Write the NCB fingerprint into the page buffer. */
+	memset(buffer, ~0, mtd->writesize);
+	memset(chip->oob_poi, ~0, mtd->oobsize);
+	memcpy(buffer + 12, fingerprint, strlen(fingerprint));
+
+	/* Loop through the first search area, writing NCB fingerprints. */
+	dev_dbg(dev, "Writing NCB fingerprints...\n");
+	for (stride = 0; stride < search_area_size_in_strides; stride++) {
+		/* Compute the page and byte addresses. */
+		page = stride * rom_geo->stride_size_in_pages;
+		byte = page   * mtd->writesize;
+
+		/* Write the first page of the current stride. */
+		dev_dbg(dev, "Writing an NCB fingerprint in page 0x%x\n", page);
+		chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page);
+		chip->ecc.write_page_raw(mtd, chip, buffer);
+		chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+
+		/* Wait for the write to finish. */
+		status = chip->waitfunc(mtd, chip);
+		if (status & NAND_STATUS_FAIL)
+			dev_err(dev, "[%s] Write failed.\n", __func__);
+	}
+
+	/* Deselect chip 0. */
+	chip->select_chip(mtd, saved_chip_number);
+	return 0;
+}
+
+static int __devinit mx23_boot_init(struct gpmi_nand_data  *this)
+{
+	struct device *dev = this->dev;
+	struct nand_chip *chip = &this->nand;
+	struct mtd_info *mtd = &this->mtd;
+	unsigned int block_count;
+	unsigned int block;
+	int     chipnr;
+	int     page;
+	loff_t  byte;
+	uint8_t block_mark;
+	int     ret = 0;
+
+	/*
+	 * If control arrives here, we can't use block mark swapping, which
+	 * means we're forced to use transcription. First, scan for the
+	 * transcription stamp. If we find it, then we don't have to do
+	 * anything -- the block marks are already transcribed.
+	 */
+	if (mx23_check_transcription_stamp(this))
+		return 0;
+
+	/*
+	 * If control arrives here, we couldn't find a transcription stamp, so
+	 * so we presume the block marks are in the conventional location.
+	 */
+	dev_dbg(dev, "Transcribing bad block marks...\n");
+
+	/* Compute the number of blocks in the entire medium. */
+	block_count = chip->chipsize >> chip->phys_erase_shift;
+
+	/*
+	 * Loop over all the blocks in the medium, transcribing block marks as
+	 * we go.
+	 */
+	for (block = 0; block < block_count; block++) {
+		/*
+		 * Compute the chip, page and byte addresses for this block's
+		 * conventional mark.
+		 */
+		chipnr = block >> (chip->chip_shift - chip->phys_erase_shift);
+		page = block << (chip->phys_erase_shift - chip->page_shift);
+		byte = block <<  chip->phys_erase_shift;
+
+		/* Send the command to read the conventional block mark. */
+		chip->select_chip(mtd, chipnr);
+		chip->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page);
+		block_mark = chip->read_byte(mtd);
+		chip->select_chip(mtd, -1);
+
+		/*
+		 * Check if the block is marked bad. If so, we need to mark it
+		 * again, but this time the result will be a mark in the
+		 * location where we transcribe block marks.
+		 */
+		if (block_mark != 0xff) {
+			dev_dbg(dev, "Transcribing mark in block %u\n", block);
+			ret = chip->block_markbad(mtd, byte);
+			if (ret)
+				dev_err(dev, "Failed to mark block bad with "
+							"ret %d\n", ret);
+		}
+	}
+
+	/* Write the stamp that indicates we've transcribed the block marks. */
+	mx23_write_transcription_stamp(this);
+	return 0;
+}
+
+static int __devinit nand_boot_init(struct gpmi_nand_data  *this)
+{
+	nand_boot_set_geometry(this);
+
+	/* This is ROM arch-specific initilization before the BBT scanning. */
+	if (GPMI_IS_MX23(this))
+		return mx23_boot_init(this);
+	return 0;
+}
+
+static int __devinit gpmi_set_geometry(struct gpmi_nand_data *this)
+{
+	int ret;
+
+	/* Free the temporary DMA memory for reading ID. */
+	gpmi_free_dma_buffer(this);
+
+	/* Set up the NFC geometry which is used by BCH. */
+	ret = bch_set_geometry(this);
+	if (ret) {
+		pr_err("set geometry ret : %d\n", ret);
+		return ret;
+	}
+
+	/* Alloc the new DMA buffers according to the pagesize and oobsize */
+	return gpmi_alloc_dma_buffer(this);
+}
+
+static int gpmi_pre_bbt_scan(struct gpmi_nand_data  *this)
+{
+	int ret;
+
+	/* Set up swap_block_mark, must be set before the gpmi_set_geometry() */
+	if (GPMI_IS_MX23(this))
+		this->swap_block_mark = false;
+	else
+		this->swap_block_mark = true;
+
+	/* Set up the medium geometry */
+	ret = gpmi_set_geometry(this);
+	if (ret)
+		return ret;
+
+	/* NAND boot init, depends on the gpmi_set_geometry(). */
+	return nand_boot_init(this);
+}
+
+static int gpmi_scan_bbt(struct mtd_info *mtd)
+{
+	struct nand_chip *chip = mtd->priv;
+	struct gpmi_nand_data *this = chip->priv;
+	int ret;
+
+	/* Prepare for the BBT scan. */
+	ret = gpmi_pre_bbt_scan(this);
+	if (ret)
+		return ret;
+
+	/* use the default BBT implementation */
+	return nand_default_bbt(mtd);
+}
+
+void gpmi_nfc_exit(struct gpmi_nand_data *this)
+{
+	nand_release(&this->mtd);
+	gpmi_free_dma_buffer(this);
+}
+
+static int __devinit gpmi_nfc_init(struct gpmi_nand_data *this)
+{
+	struct gpmi_nand_platform_data *pdata = this->pdata;
+	struct mtd_info  *mtd = &this->mtd;
+	struct nand_chip *chip = &this->nand;
+	int ret;
+
+	/* init current chip */
+	this->current_chip	= -1;
+
+	/* init the MTD data structures */
+	mtd->priv		= chip;
+	mtd->name		= "gpmi-nand";
+	mtd->owner		= THIS_MODULE;
+
+	/* init the nand_chip{}, we don't support a 16-bit NAND Flash bus. */
+	chip->priv		= this;
+	chip->select_chip	= gpmi_select_chip;
+	chip->cmd_ctrl		= gpmi_cmd_ctrl;
+	chip->dev_ready		= gpmi_dev_ready;
+	chip->read_byte		= gpmi_read_byte;
+	chip->read_buf		= gpmi_read_buf;
+	chip->write_buf		= gpmi_write_buf;
+	chip->ecc.read_page	= gpmi_ecc_read_page;
+	chip->ecc.write_page	= gpmi_ecc_write_page;
+	chip->ecc.read_oob	= gpmi_ecc_read_oob;
+	chip->ecc.write_oob	= gpmi_ecc_write_oob;
+	chip->scan_bbt		= gpmi_scan_bbt;
+	chip->badblock_pattern	= &gpmi_bbt_descr;
+	chip->block_markbad	= gpmi_block_markbad;
+	chip->options		|= NAND_NO_SUBPAGE_WRITE;
+	chip->ecc.mode		= NAND_ECC_HW;
+	chip->ecc.size		= 1;
+	chip->ecc.layout	= &gpmi_hw_ecclayout;
+
+	/* Allocate a temporary DMA buffer for reading ID in the nand_scan() */
+	this->bch_geometry.payload_size = 1024;
+	this->bch_geometry.auxiliary_size = 128;
+	ret = gpmi_alloc_dma_buffer(this);
+	if (ret)
+		goto err_out;
+
+	ret = nand_scan(mtd, pdata->max_chip_count);
+	if (ret) {
+		pr_err("Chip scan failed\n");
+		goto err_out;
+	}
+
+	ret = mtd_device_parse_register(mtd, NULL, NULL,
+			pdata->partitions, pdata->partition_count);
+	if (ret)
+		goto err_out;
+	return 0;
+
+err_out:
+	gpmi_nfc_exit(this);
+	return ret;
+}
+
+static int __devinit gpmi_nand_probe(struct platform_device *pdev)
+{
+	struct gpmi_nand_platform_data *pdata = pdev->dev.platform_data;
+	struct gpmi_nand_data *this;
+	int ret;
+
+	this = kzalloc(sizeof(*this), GFP_KERNEL);
+	if (!this) {
+		pr_err("Failed to allocate per-device memory\n");
+		return -ENOMEM;
+	}
+
+	platform_set_drvdata(pdev, this);
+	this->pdev  = pdev;
+	this->dev   = &pdev->dev;
+	this->pdata = pdata;
+
+	if (pdata->platform_init) {
+		ret = pdata->platform_init();
+		if (ret)
+			goto platform_init_error;
+	}
+
+	ret = acquire_resources(this);
+	if (ret)
+		goto exit_acquire_resources;
+
+	ret = init_hardware(this);
+	if (ret)
+		goto exit_nfc_init;
+
+	ret = gpmi_nfc_init(this);
+	if (ret)
+		goto exit_nfc_init;
+
+	return 0;
+
+exit_nfc_init:
+	release_resources(this);
+platform_init_error:
+exit_acquire_resources:
+	platform_set_drvdata(pdev, NULL);
+	kfree(this);
+	return ret;
+}
+
+static int __exit gpmi_nand_remove(struct platform_device *pdev)
+{
+	struct gpmi_nand_data *this = platform_get_drvdata(pdev);
+
+	gpmi_nfc_exit(this);
+	release_resources(this);
+	platform_set_drvdata(pdev, NULL);
+	kfree(this);
+	return 0;
+}
+
+static const struct platform_device_id gpmi_ids[] = {
+	{
+		.name = "imx23-gpmi-nand",
+		.driver_data = IS_MX23,
+	}, {
+		.name = "imx28-gpmi-nand",
+		.driver_data = IS_MX28,
+	}, {},
+};
+
+static struct platform_driver gpmi_nand_driver = {
+	.driver = {
+		.name = "gpmi-nand",
+	},
+	.probe   = gpmi_nand_probe,
+	.remove  = __exit_p(gpmi_nand_remove),
+	.id_table = gpmi_ids,
+};
+
+static int __init gpmi_nand_init(void)
+{
+	int err;
+
+	err = platform_driver_register(&gpmi_nand_driver);
+	if (err == 0)
+		printk(KERN_INFO "GPMI NAND driver registered. (IMX)\n");
+	else
+		pr_err("i.MX GPMI NAND driver registration failed\n");
+	return err;
+}
+
+static void __exit gpmi_nand_exit(void)
+{
+	platform_driver_unregister(&gpmi_nand_driver);
+}
+
+module_init(gpmi_nand_init);
+module_exit(gpmi_nand_exit);
+
+MODULE_AUTHOR("Freescale Semiconductor, Inc.");
+MODULE_DESCRIPTION("i.MX GPMI NAND Flash Controller Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h
new file mode 100644
index 000000000000..e023bccb7781
--- /dev/null
+++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h
@@ -0,0 +1,273 @@
+/*
+ * Freescale GPMI NAND Flash Driver
+ *
+ * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
+ * Copyright (C) 2008 Embedded Alley Solutions, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+#ifndef __DRIVERS_MTD_NAND_GPMI_NAND_H
+#define __DRIVERS_MTD_NAND_GPMI_NAND_H
+
+#include <linux/mtd/nand.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <mach/dma.h>
+
+struct resources {
+	void          *gpmi_regs;
+	void          *bch_regs;
+	unsigned int  bch_low_interrupt;
+	unsigned int  bch_high_interrupt;
+	unsigned int  dma_low_channel;
+	unsigned int  dma_high_channel;
+	struct clk    *clock;
+};
+
+/**
+ * struct bch_geometry - BCH geometry description.
+ * @gf_len:                   The length of Galois Field. (e.g., 13 or 14)
+ * @ecc_strength:             A number that describes the strength of the ECC
+ *                            algorithm.
+ * @page_size:                The size, in bytes, of a physical page, including
+ *                            both data and OOB.
+ * @metadata_size:            The size, in bytes, of the metadata.
+ * @ecc_chunk_size:           The size, in bytes, of a single ECC chunk. Note
+ *                            the first chunk in the page includes both data and
+ *                            metadata, so it's a bit larger than this value.
+ * @ecc_chunk_count:          The number of ECC chunks in the page,
+ * @payload_size:             The size, in bytes, of the payload buffer.
+ * @auxiliary_size:           The size, in bytes, of the auxiliary buffer.
+ * @auxiliary_status_offset:  The offset into the auxiliary buffer at which
+ *                            the ECC status appears.
+ * @block_mark_byte_offset:   The byte offset in the ECC-based page view at
+ *                            which the underlying physical block mark appears.
+ * @block_mark_bit_offset:    The bit offset into the ECC-based page view at
+ *                            which the underlying physical block mark appears.
+ */
+struct bch_geometry {
+	unsigned int  gf_len;
+	unsigned int  ecc_strength;
+	unsigned int  page_size;
+	unsigned int  metadata_size;
+	unsigned int  ecc_chunk_size;
+	unsigned int  ecc_chunk_count;
+	unsigned int  payload_size;
+	unsigned int  auxiliary_size;
+	unsigned int  auxiliary_status_offset;
+	unsigned int  block_mark_byte_offset;
+	unsigned int  block_mark_bit_offset;
+};
+
+/**
+ * struct boot_rom_geometry - Boot ROM geometry description.
+ * @stride_size_in_pages:        The size of a boot block stride, in pages.
+ * @search_area_stride_exponent: The logarithm to base 2 of the size of a
+ *                               search area in boot block strides.
+ */
+struct boot_rom_geometry {
+	unsigned int  stride_size_in_pages;
+	unsigned int  search_area_stride_exponent;
+};
+
+/* DMA operations types */
+enum dma_ops_type {
+	DMA_FOR_COMMAND = 1,
+	DMA_FOR_READ_DATA,
+	DMA_FOR_WRITE_DATA,
+	DMA_FOR_READ_ECC_PAGE,
+	DMA_FOR_WRITE_ECC_PAGE
+};
+
+/**
+ * struct nand_timing - Fundamental timing attributes for NAND.
+ * @data_setup_in_ns:         The data setup time, in nanoseconds. Usually the
+ *                            maximum of tDS and tWP. A negative value
+ *                            indicates this characteristic isn't known.
+ * @data_hold_in_ns:          The data hold time, in nanoseconds. Usually the
+ *                            maximum of tDH, tWH and tREH. A negative value
+ *                            indicates this characteristic isn't known.
+ * @address_setup_in_ns:      The address setup time, in nanoseconds. Usually
+ *                            the maximum of tCLS, tCS and tALS. A negative
+ *                            value indicates this characteristic isn't known.
+ * @gpmi_sample_delay_in_ns:  A GPMI-specific timing parameter. A negative value
+ *                            indicates this characteristic isn't known.
+ * @tREA_in_ns:               tREA, in nanoseconds, from the data sheet. A
+ *                            negative value indicates this characteristic isn't
+ *                            known.
+ * @tRLOH_in_ns:              tRLOH, in nanoseconds, from the data sheet. A
+ *                            negative value indicates this characteristic isn't
+ *                            known.
+ * @tRHOH_in_ns:              tRHOH, in nanoseconds, from the data sheet. A
+ *                            negative value indicates this characteristic isn't
+ *                            known.
+ */
+struct nand_timing {
+	int8_t  data_setup_in_ns;
+	int8_t  data_hold_in_ns;
+	int8_t  address_setup_in_ns;
+	int8_t  gpmi_sample_delay_in_ns;
+	int8_t  tREA_in_ns;
+	int8_t  tRLOH_in_ns;
+	int8_t  tRHOH_in_ns;
+};
+
+struct gpmi_nand_data {
+	/* System Interface */
+	struct device		*dev;
+	struct platform_device	*pdev;
+	struct gpmi_nand_platform_data	*pdata;
+
+	/* Resources */
+	struct resources	resources;
+
+	/* Flash Hardware */
+	struct nand_timing	timing;
+
+	/* BCH */
+	struct bch_geometry	bch_geometry;
+	struct completion	bch_done;
+
+	/* NAND Boot issue */
+	bool			swap_block_mark;
+	struct boot_rom_geometry rom_geometry;
+
+	/* MTD / NAND */
+	struct nand_chip	nand;
+	struct mtd_info		mtd;
+
+	/* General-use Variables */
+	int			current_chip;
+	unsigned int		command_length;
+
+	/* passed from upper layer */
+	uint8_t			*upper_buf;
+	int			upper_len;
+
+	/* for DMA operations */
+	bool			direct_dma_map_ok;
+
+	struct scatterlist	cmd_sgl;
+	char			*cmd_buffer;
+
+	struct scatterlist	data_sgl;
+	char			*data_buffer_dma;
+
+	void			*page_buffer_virt;
+	dma_addr_t		page_buffer_phys;
+	unsigned int		page_buffer_size;
+
+	void			*payload_virt;
+	dma_addr_t		payload_phys;
+
+	void			*auxiliary_virt;
+	dma_addr_t		auxiliary_phys;
+
+	/* DMA channels */
+#define DMA_CHANS		8
+	struct dma_chan		*dma_chans[DMA_CHANS];
+	struct mxs_dma_data	dma_data;
+	enum dma_ops_type	last_dma_type;
+	enum dma_ops_type	dma_type;
+	struct completion	dma_done;
+
+	/* private */
+	void			*private;
+};
+
+/**
+ * struct gpmi_nfc_hardware_timing - GPMI hardware timing parameters.
+ * @data_setup_in_cycles:      The data setup time, in cycles.
+ * @data_hold_in_cycles:       The data hold time, in cycles.
+ * @address_setup_in_cycles:   The address setup time, in cycles.
+ * @use_half_periods:          Indicates the clock is running slowly, so the
+ *                             NFC DLL should use half-periods.
+ * @sample_delay_factor:       The sample delay factor.
+ */
+struct gpmi_nfc_hardware_timing {
+	uint8_t  data_setup_in_cycles;
+	uint8_t  data_hold_in_cycles;
+	uint8_t  address_setup_in_cycles;
+	bool     use_half_periods;
+	uint8_t  sample_delay_factor;
+};
+
+/**
+ * struct timing_threshod - Timing threshold
+ * @max_data_setup_cycles:       The maximum number of data setup cycles that
+ *                               can be expressed in the hardware.
+ * @internal_data_setup_in_ns:   The time, in ns, that the NFC hardware requires
+ *                               for data read internal setup. In the Reference
+ *                               Manual, see the chapter "High-Speed NAND
+ *                               Timing" for more details.
+ * @max_sample_delay_factor:     The maximum sample delay factor that can be
+ *                               expressed in the hardware.
+ * @max_dll_clock_period_in_ns:  The maximum period of the GPMI clock that the
+ *                               sample delay DLL hardware can possibly work
+ *                               with (the DLL is unusable with longer periods).
+ *                               If the full-cycle period is greater than HALF
+ *                               this value, the DLL must be configured to use
+ *                               half-periods.
+ * @max_dll_delay_in_ns:         The maximum amount of delay, in ns, that the
+ *                               DLL can implement.
+ * @clock_frequency_in_hz:       The clock frequency, in Hz, during the current
+ *                               I/O transaction. If no I/O transaction is in
+ *                               progress, this is the clock frequency during
+ *                               the most recent I/O transaction.
+ */
+struct timing_threshod {
+	const unsigned int      max_chip_count;
+	const unsigned int      max_data_setup_cycles;
+	const unsigned int      internal_data_setup_in_ns;
+	const unsigned int      max_sample_delay_factor;
+	const unsigned int      max_dll_clock_period_in_ns;
+	const unsigned int      max_dll_delay_in_ns;
+	unsigned long           clock_frequency_in_hz;
+
+};
+
+/* Common Services */
+extern int common_nfc_set_geometry(struct gpmi_nand_data *);
+extern struct dma_chan *get_dma_chan(struct gpmi_nand_data *);
+extern void prepare_data_dma(struct gpmi_nand_data *,
+				enum dma_data_direction dr);
+extern int start_dma_without_bch_irq(struct gpmi_nand_data *,
+				struct dma_async_tx_descriptor *);
+extern int start_dma_with_bch_irq(struct gpmi_nand_data *,
+				struct dma_async_tx_descriptor *);
+
+/* GPMI-NAND helper function library */
+extern int gpmi_init(struct gpmi_nand_data *);
+extern void gpmi_clear_bch(struct gpmi_nand_data *);
+extern void gpmi_dump_info(struct gpmi_nand_data *);
+extern int bch_set_geometry(struct gpmi_nand_data *);
+extern int gpmi_is_ready(struct gpmi_nand_data *, unsigned chip);
+extern int gpmi_send_command(struct gpmi_nand_data *);
+extern void gpmi_begin(struct gpmi_nand_data *);
+extern void gpmi_end(struct gpmi_nand_data *);
+extern int gpmi_read_data(struct gpmi_nand_data *);
+extern int gpmi_send_data(struct gpmi_nand_data *);
+extern int gpmi_send_page(struct gpmi_nand_data *,
+			dma_addr_t payload, dma_addr_t auxiliary);
+extern int gpmi_read_page(struct gpmi_nand_data *,
+			dma_addr_t payload, dma_addr_t auxiliary);
+
+/* BCH : Status Block Completion Codes */
+#define STATUS_GOOD		0x00
+#define STATUS_ERASED		0xff
+#define STATUS_UNCORRECTABLE	0xfe
+
+/* Use the platform_id to distinguish different Archs. */
+#define IS_MX23			0x1
+#define IS_MX28			0x2
+#define GPMI_IS_MX23(x)		((x)->pdev->id_entry->driver_data == IS_MX23)
+#define GPMI_IS_MX28(x)		((x)->pdev->id_entry->driver_data == IS_MX28)
+#endif
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-regs.h b/drivers/mtd/nand/gpmi-nand/gpmi-regs.h
new file mode 100644
index 000000000000..83431240e2f2
--- /dev/null
+++ b/drivers/mtd/nand/gpmi-nand/gpmi-regs.h
@@ -0,0 +1,172 @@
+/*
+ * Freescale GPMI NAND Flash Driver
+ *
+ * Copyright 2008-2011 Freescale Semiconductor, Inc.
+ * Copyright 2008 Embedded Alley Solutions, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+#ifndef __GPMI_NAND_GPMI_REGS_H
+#define __GPMI_NAND_GPMI_REGS_H
+
+#define HW_GPMI_CTRL0					0x00000000
+#define HW_GPMI_CTRL0_SET				0x00000004
+#define HW_GPMI_CTRL0_CLR				0x00000008
+#define HW_GPMI_CTRL0_TOG				0x0000000c
+
+#define BP_GPMI_CTRL0_COMMAND_MODE			24
+#define BM_GPMI_CTRL0_COMMAND_MODE	(3 << BP_GPMI_CTRL0_COMMAND_MODE)
+#define BF_GPMI_CTRL0_COMMAND_MODE(v)	\
+	(((v) << BP_GPMI_CTRL0_COMMAND_MODE) & BM_GPMI_CTRL0_COMMAND_MODE)
+#define BV_GPMI_CTRL0_COMMAND_MODE__WRITE		0x0
+#define BV_GPMI_CTRL0_COMMAND_MODE__READ		0x1
+#define BV_GPMI_CTRL0_COMMAND_MODE__READ_AND_COMPARE	0x2
+#define BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY	0x3
+
+#define BM_GPMI_CTRL0_WORD_LENGTH			(1 << 23)
+#define BV_GPMI_CTRL0_WORD_LENGTH__16_BIT		0x0
+#define BV_GPMI_CTRL0_WORD_LENGTH__8_BIT		0x1
+
+/*
+ *  Difference in LOCK_CS between imx23 and imx28 :
+ *  This bit may impact the _POWER_ consumption. So some chips
+ *  do not set it.
+ */
+#define MX23_BP_GPMI_CTRL0_LOCK_CS			22
+#define MX28_BP_GPMI_CTRL0_LOCK_CS			27
+#define LOCK_CS_ENABLE					0x1
+#define BF_GPMI_CTRL0_LOCK_CS(v, x)			0x0
+
+/* Difference in CS between imx23 and imx28 */
+#define BP_GPMI_CTRL0_CS				20
+#define MX23_BM_GPMI_CTRL0_CS		(3 << BP_GPMI_CTRL0_CS)
+#define MX28_BM_GPMI_CTRL0_CS		(7 << BP_GPMI_CTRL0_CS)
+#define BF_GPMI_CTRL0_CS(v, x)		(((v) << BP_GPMI_CTRL0_CS) & \
+						(GPMI_IS_MX23((x)) \
+						? MX23_BM_GPMI_CTRL0_CS	\
+						: MX28_BM_GPMI_CTRL0_CS))
+
+#define BP_GPMI_CTRL0_ADDRESS				17
+#define BM_GPMI_CTRL0_ADDRESS		(3 << BP_GPMI_CTRL0_ADDRESS)
+#define BF_GPMI_CTRL0_ADDRESS(v)	\
+		(((v) << BP_GPMI_CTRL0_ADDRESS) & BM_GPMI_CTRL0_ADDRESS)
+#define BV_GPMI_CTRL0_ADDRESS__NAND_DATA		0x0
+#define BV_GPMI_CTRL0_ADDRESS__NAND_CLE			0x1
+#define BV_GPMI_CTRL0_ADDRESS__NAND_ALE			0x2
+
+#define BM_GPMI_CTRL0_ADDRESS_INCREMENT			(1 << 16)
+#define BV_GPMI_CTRL0_ADDRESS_INCREMENT__DISABLED	0x0
+#define BV_GPMI_CTRL0_ADDRESS_INCREMENT__ENABLED	0x1
+
+#define BP_GPMI_CTRL0_XFER_COUNT			0
+#define BM_GPMI_CTRL0_XFER_COUNT	(0xffff << BP_GPMI_CTRL0_XFER_COUNT)
+#define BF_GPMI_CTRL0_XFER_COUNT(v)	\
+		(((v) << BP_GPMI_CTRL0_XFER_COUNT) & BM_GPMI_CTRL0_XFER_COUNT)
+
+#define HW_GPMI_COMPARE					0x00000010
+
+#define HW_GPMI_ECCCTRL					0x00000020
+#define HW_GPMI_ECCCTRL_SET				0x00000024
+#define HW_GPMI_ECCCTRL_CLR				0x00000028
+#define HW_GPMI_ECCCTRL_TOG				0x0000002c
+
+#define BP_GPMI_ECCCTRL_ECC_CMD				13
+#define BM_GPMI_ECCCTRL_ECC_CMD		(3 << BP_GPMI_ECCCTRL_ECC_CMD)
+#define BF_GPMI_ECCCTRL_ECC_CMD(v)	\
+		(((v) << BP_GPMI_ECCCTRL_ECC_CMD) & BM_GPMI_ECCCTRL_ECC_CMD)
+#define BV_GPMI_ECCCTRL_ECC_CMD__BCH_DECODE		0x0
+#define BV_GPMI_ECCCTRL_ECC_CMD__BCH_ENCODE		0x1
+
+#define BM_GPMI_ECCCTRL_ENABLE_ECC			(1 << 12)
+#define BV_GPMI_ECCCTRL_ENABLE_ECC__ENABLE		0x1
+#define BV_GPMI_ECCCTRL_ENABLE_ECC__DISABLE		0x0
+
+#define BP_GPMI_ECCCTRL_BUFFER_MASK			0
+#define BM_GPMI_ECCCTRL_BUFFER_MASK	(0x1ff << BP_GPMI_ECCCTRL_BUFFER_MASK)
+#define BF_GPMI_ECCCTRL_BUFFER_MASK(v)	\
+	(((v) << BP_GPMI_ECCCTRL_BUFFER_MASK) & BM_GPMI_ECCCTRL_BUFFER_MASK)
+#define BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY	0x100
+#define BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE		0x1FF
+
+#define HW_GPMI_ECCCOUNT				0x00000030
+#define HW_GPMI_PAYLOAD					0x00000040
+#define HW_GPMI_AUXILIARY				0x00000050
+#define HW_GPMI_CTRL1					0x00000060
+#define HW_GPMI_CTRL1_SET				0x00000064
+#define HW_GPMI_CTRL1_CLR				0x00000068
+#define HW_GPMI_CTRL1_TOG				0x0000006c
+
+#define BM_GPMI_CTRL1_BCH_MODE				(1 << 18)
+
+#define BP_GPMI_CTRL1_DLL_ENABLE			17
+#define BM_GPMI_CTRL1_DLL_ENABLE	(1 << BP_GPMI_CTRL1_DLL_ENABLE)
+
+#define BP_GPMI_CTRL1_HALF_PERIOD			16
+#define BM_GPMI_CTRL1_HALF_PERIOD	(1 << BP_GPMI_CTRL1_HALF_PERIOD)
+
+#define BP_GPMI_CTRL1_RDN_DELAY				12
+#define BM_GPMI_CTRL1_RDN_DELAY		(0xf << BP_GPMI_CTRL1_RDN_DELAY)
+#define BF_GPMI_CTRL1_RDN_DELAY(v)	\
+		(((v) << BP_GPMI_CTRL1_RDN_DELAY) & BM_GPMI_CTRL1_RDN_DELAY)
+
+#define BM_GPMI_CTRL1_DEV_RESET				(1 << 3)
+#define BV_GPMI_CTRL1_DEV_RESET__ENABLED		0x0
+#define BV_GPMI_CTRL1_DEV_RESET__DISABLED		0x1
+
+#define BM_GPMI_CTRL1_ATA_IRQRDY_POLARITY		(1 << 2)
+#define BV_GPMI_CTRL1_ATA_IRQRDY_POLARITY__ACTIVELOW	0x0
+#define BV_GPMI_CTRL1_ATA_IRQRDY_POLARITY__ACTIVEHIGH	0x1
+
+#define BM_GPMI_CTRL1_CAMERA_MODE			(1 << 1)
+#define BV_GPMI_CTRL1_GPMI_MODE__NAND			0x0
+#define BV_GPMI_CTRL1_GPMI_MODE__ATA			0x1
+
+#define BM_GPMI_CTRL1_GPMI_MODE				(1 << 0)
+
+#define HW_GPMI_TIMING0					0x00000070
+
+#define BP_GPMI_TIMING0_ADDRESS_SETUP			16
+#define BM_GPMI_TIMING0_ADDRESS_SETUP	(0xff << BP_GPMI_TIMING0_ADDRESS_SETUP)
+#define BF_GPMI_TIMING0_ADDRESS_SETUP(v)	\
+	(((v) << BP_GPMI_TIMING0_ADDRESS_SETUP) & BM_GPMI_TIMING0_ADDRESS_SETUP)
+
+#define BP_GPMI_TIMING0_DATA_HOLD			8
+#define BM_GPMI_TIMING0_DATA_HOLD	(0xff << BP_GPMI_TIMING0_DATA_HOLD)
+#define BF_GPMI_TIMING0_DATA_HOLD(v)		\
+	(((v) << BP_GPMI_TIMING0_DATA_HOLD) & BM_GPMI_TIMING0_DATA_HOLD)
+
+#define BP_GPMI_TIMING0_DATA_SETUP			0
+#define BM_GPMI_TIMING0_DATA_SETUP	(0xff << BP_GPMI_TIMING0_DATA_SETUP)
+#define BF_GPMI_TIMING0_DATA_SETUP(v)		\
+	(((v) << BP_GPMI_TIMING0_DATA_SETUP) & BM_GPMI_TIMING0_DATA_SETUP)
+
+#define HW_GPMI_TIMING1					0x00000080
+#define BP_GPMI_TIMING1_BUSY_TIMEOUT			16
+
+#define HW_GPMI_TIMING2					0x00000090
+#define HW_GPMI_DATA					0x000000a0
+
+/* MX28 uses this to detect READY. */
+#define HW_GPMI_STAT					0x000000b0
+#define MX28_BP_GPMI_STAT_READY_BUSY			24
+#define MX28_BM_GPMI_STAT_READY_BUSY	(0xff << MX28_BP_GPMI_STAT_READY_BUSY)
+#define MX28_BF_GPMI_STAT_READY_BUSY(v)		\
+	(((v) << MX28_BP_GPMI_STAT_READY_BUSY) & MX28_BM_GPMI_STAT_READY_BUSY)
+
+/* MX23 uses this to detect READY. */
+#define HW_GPMI_DEBUG					0x000000c0
+#define MX23_BP_GPMI_DEBUG_READY0			28
+#define MX23_BM_GPMI_DEBUG_READY0	(1 << MX23_BP_GPMI_DEBUG_READY0)
+#endif
diff --git a/drivers/mtd/nand/h1910.c b/drivers/mtd/nand/h1910.c
index 02a03e67109c..5dc6f0d92f1a 100644
--- a/drivers/mtd/nand/h1910.c
+++ b/drivers/mtd/nand/h1910.c
@@ -81,9 +81,6 @@ static int h1910_device_ready(struct mtd_info *mtd)
 static int __init h1910_init(void)
 {
 	struct nand_chip *this;
-	const char *part_type = 0;
-	int mtd_parts_nb = 0;
-	struct mtd_partition *mtd_parts = 0;
 	void __iomem *nandaddr;
 
 	if (!machine_is_h1900())
@@ -136,22 +133,10 @@ static int __init h1910_init(void)
 		iounmap((void *)nandaddr);
 		return -ENXIO;
 	}
-#ifdef CONFIG_MTD_CMDLINE_PARTS
-	mtd_parts_nb = parse_cmdline_partitions(h1910_nand_mtd, &mtd_parts, "h1910-nand");
-	if (mtd_parts_nb > 0)
-		part_type = "command line";
-	else
-		mtd_parts_nb = 0;
-#endif
-	if (mtd_parts_nb == 0) {
-		mtd_parts = partition_info;
-		mtd_parts_nb = NUM_PARTITIONS;
-		part_type = "static";
-	}
 
 	/* Register the partitions */
-	printk(KERN_NOTICE "Using %s partition definition\n", part_type);
-	mtd_device_register(h1910_nand_mtd, mtd_parts, mtd_parts_nb);
+	mtd_device_parse_register(h1910_nand_mtd, NULL, 0,
+			partition_info, NUM_PARTITIONS);
 
 	/* Return happy */
 	return 0;
diff --git a/drivers/mtd/nand/jz4740_nand.c b/drivers/mtd/nand/jz4740_nand.c
index 6e813daed068..e2664073a89b 100644
--- a/drivers/mtd/nand/jz4740_nand.c
+++ b/drivers/mtd/nand/jz4740_nand.c
@@ -251,10 +251,6 @@ static int jz_nand_correct_ecc_rs(struct mtd_info *mtd, uint8_t *dat,
 	return 0;
 }
 
-#ifdef CONFIG_MTD_CMDLINE_PARTS
-static const char *part_probes[] = {"cmdline", NULL};
-#endif
-
 static int jz_nand_ioremap_resource(struct platform_device *pdev,
 	const char *name, struct resource **res, void __iomem **base)
 {
@@ -299,8 +295,6 @@ static int __devinit jz_nand_probe(struct platform_device *pdev)
 	struct nand_chip *chip;
 	struct mtd_info *mtd;
 	struct jz_nand_platform_data *pdata = pdev->dev.platform_data;
-	struct mtd_partition *partition_info;
-	int num_partitions = 0;
 
 	nand = kzalloc(sizeof(*nand), GFP_KERNEL);
 	if (!nand) {
@@ -373,15 +367,9 @@ static int __devinit jz_nand_probe(struct platform_device *pdev)
 		goto err_gpio_free;
 	}
 
-#ifdef CONFIG_MTD_CMDLINE_PARTS
-	num_partitions = parse_mtd_partitions(mtd, part_probes,
-						&partition_info, 0);
-#endif
-	if (num_partitions <= 0 && pdata) {
-		num_partitions = pdata->num_partitions;
-		partition_info = pdata->partitions;
-	}
-	ret = mtd_device_register(mtd, partition_info, num_partitions);
+	ret = mtd_device_parse_register(mtd, NULL, 0,
+			pdata ? pdata->partitions : NULL,
+			pdata ? pdata->num_partitions : 0);
 
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to add mtd device\n");
diff --git a/drivers/mtd/nand/mpc5121_nfc.c b/drivers/mtd/nand/mpc5121_nfc.c
index eb1fbac63eb6..5ede64706346 100644
--- a/drivers/mtd/nand/mpc5121_nfc.c
+++ b/drivers/mtd/nand/mpc5121_nfc.c
@@ -131,8 +131,6 @@ struct mpc5121_nfc_prv {
 
 static void mpc5121_nfc_done(struct mtd_info *mtd);
 
-static const char *mpc5121_nfc_pprobes[] = { "cmdlinepart", NULL };
-
 /* Read NFC register */
 static inline u16 nfc_read(struct mtd_info *mtd, uint reg)
 {
@@ -656,13 +654,13 @@ static int __devinit mpc5121_nfc_probe(struct platform_device *op)
 	struct mpc5121_nfc_prv *prv;
 	struct resource res;
 	struct mtd_info *mtd;
-	struct mtd_partition *parts;
 	struct nand_chip *chip;
 	unsigned long regs_paddr, regs_size;
 	const __be32 *chips_no;
 	int resettime = 0;
 	int retval = 0;
 	int rev, len;
+	struct mtd_part_parser_data ppdata;
 
 	/*
 	 * Check SoC revision. This driver supports only NFC
@@ -727,6 +725,7 @@ static int __devinit mpc5121_nfc_probe(struct platform_device *op)
 	}
 
 	mtd->name = "MPC5121 NAND";
+	ppdata.of_node = dn;
 	chip->dev_ready = mpc5121_nfc_dev_ready;
 	chip->cmdfunc = mpc5121_nfc_command;
 	chip->read_byte = mpc5121_nfc_read_byte;
@@ -735,7 +734,8 @@ static int __devinit mpc5121_nfc_probe(struct platform_device *op)
 	chip->write_buf = mpc5121_nfc_write_buf;
 	chip->verify_buf = mpc5121_nfc_verify_buf;
 	chip->select_chip = mpc5121_nfc_select_chip;
-	chip->options = NAND_NO_AUTOINCR | NAND_USE_FLASH_BBT;
+	chip->options = NAND_NO_AUTOINCR;
+	chip->bbt_options = NAND_BBT_USE_FLASH;
 	chip->ecc.mode = NAND_ECC_SOFT;
 
 	/* Support external chip-select logic on ADS5121 board */
@@ -837,19 +837,7 @@ static int __devinit mpc5121_nfc_probe(struct platform_device *op)
 	dev_set_drvdata(dev, mtd);
 
 	/* Register device in MTD */
-	retval = parse_mtd_partitions(mtd, mpc5121_nfc_pprobes, &parts, 0);
-#ifdef CONFIG_MTD_OF_PARTS
-	if (retval == 0)
-		retval = of_mtd_parse_partitions(dev, dn, &parts);
-#endif
-	if (retval < 0) {
-		dev_err(dev, "Error parsing MTD partitions!\n");
-		devm_free_irq(dev, prv->irq, mtd);
-		retval = -EINVAL;
-		goto error;
-	}
-
-	retval = mtd_device_register(mtd, parts, retval);
+	retval = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0);
 	if (retval) {
 		dev_err(dev, "Error adding MTD device!\n");
 		devm_free_irq(dev, prv->irq, mtd);
diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c
index 90df34c4d26c..74a43b818d0e 100644
--- a/drivers/mtd/nand/mxc_nand.c
+++ b/drivers/mtd/nand/mxc_nand.c
@@ -41,7 +41,7 @@
 
 #define nfc_is_v21()		(cpu_is_mx25() || cpu_is_mx35())
 #define nfc_is_v1()		(cpu_is_mx31() || cpu_is_mx27() || cpu_is_mx21())
-#define nfc_is_v3_2()		cpu_is_mx51()
+#define nfc_is_v3_2()		(cpu_is_mx51() || cpu_is_mx53())
 #define nfc_is_v3()		nfc_is_v3_2()
 
 /* Addresses for NFC registers */
@@ -143,7 +143,6 @@
 struct mxc_nand_host {
 	struct mtd_info		mtd;
 	struct nand_chip	nand;
-	struct mtd_partition	*parts;
 	struct device		*dev;
 
 	void			*spare0;
@@ -350,8 +349,7 @@ static void wait_op_done(struct mxc_nand_host *host, int useirq)
 			udelay(1);
 		}
 		if (max_retries < 0)
-			DEBUG(MTD_DEBUG_LEVEL0, "%s: INT not set\n",
-			      __func__);
+			pr_debug("%s: INT not set\n", __func__);
 	}
 }
 
@@ -371,7 +369,7 @@ static void send_cmd_v3(struct mxc_nand_host *host, uint16_t cmd, int useirq)
  * waits for completion. */
 static void send_cmd_v1_v2(struct mxc_nand_host *host, uint16_t cmd, int useirq)
 {
-	DEBUG(MTD_DEBUG_LEVEL3, "send_cmd(host, 0x%x, %d)\n", cmd, useirq);
+	pr_debug("send_cmd(host, 0x%x, %d)\n", cmd, useirq);
 
 	writew(cmd, NFC_V1_V2_FLASH_CMD);
 	writew(NFC_CMD, NFC_V1_V2_CONFIG2);
@@ -387,8 +385,7 @@ static void send_cmd_v1_v2(struct mxc_nand_host *host, uint16_t cmd, int useirq)
 			udelay(1);
 		}
 		if (max_retries < 0)
-			DEBUG(MTD_DEBUG_LEVEL0, "%s: RESET failed\n",
-			      __func__);
+			pr_debug("%s: RESET failed\n", __func__);
 	} else {
 		/* Wait for operation to complete */
 		wait_op_done(host, useirq);
@@ -411,7 +408,7 @@ static void send_addr_v3(struct mxc_nand_host *host, uint16_t addr, int islast)
  * a NAND command. */
 static void send_addr_v1_v2(struct mxc_nand_host *host, uint16_t addr, int islast)
 {
-	DEBUG(MTD_DEBUG_LEVEL3, "send_addr(host, 0x%x %d)\n", addr, islast);
+	pr_debug("send_addr(host, 0x%x %d)\n", addr, islast);
 
 	writew(addr, NFC_V1_V2_FLASH_ADDR);
 	writew(NFC_ADDR, NFC_V1_V2_CONFIG2);
@@ -561,8 +558,7 @@ static int mxc_nand_correct_data_v1(struct mtd_info *mtd, u_char *dat,
 	uint16_t ecc_status = readw(NFC_V1_V2_ECC_STATUS_RESULT);
 
 	if (((ecc_status & 0x3) == 2) || ((ecc_status >> 2) == 2)) {
-		DEBUG(MTD_DEBUG_LEVEL0,
-		      "MXC_NAND: HWECC uncorrectable 2-bit ECC error\n");
+		pr_debug("MXC_NAND: HWECC uncorrectable 2-bit ECC error\n");
 		return -1;
 	}
 
@@ -849,7 +845,7 @@ static void preset_v1_v2(struct mtd_info *mtd)
 		writew(0xffff, NFC_V21_UNLOCKEND_BLKADDR3);
 	} else if (nfc_is_v1()) {
 		writew(0x0, NFC_V1_UNLOCKSTART_BLKADDR);
-		writew(0x4000, NFC_V1_UNLOCKEND_BLKADDR);
+		writew(0xffff, NFC_V1_UNLOCKEND_BLKADDR);
 	} else
 		BUG();
 
@@ -932,8 +928,7 @@ static void mxc_nand_command(struct mtd_info *mtd, unsigned command,
 	struct nand_chip *nand_chip = mtd->priv;
 	struct mxc_nand_host *host = nand_chip->priv;
 
-	DEBUG(MTD_DEBUG_LEVEL3,
-	      "mxc_nand_command (cmd = 0x%x, col = 0x%x, page = 0x%x)\n",
+	pr_debug("mxc_nand_command (cmd = 0x%x, col = 0x%x, page = 0x%x)\n",
 	      command, column, page_addr);
 
 	/* Reset command state information */
@@ -1044,7 +1039,7 @@ static int __init mxcnd_probe(struct platform_device *pdev)
 	struct mxc_nand_platform_data *pdata = pdev->dev.platform_data;
 	struct mxc_nand_host *host;
 	struct resource *res;
-	int err = 0, __maybe_unused nr_parts = 0;
+	int err = 0;
 	struct nand_ecclayout *oob_smallpage, *oob_largepage;
 
 	/* Allocate memory for MTD device structure and private data */
@@ -1179,7 +1174,7 @@ static int __init mxcnd_probe(struct platform_device *pdev)
 		this->bbt_td = &bbt_main_descr;
 		this->bbt_md = &bbt_mirror_descr;
 		/* update flash based bbt */
-		this->options |= NAND_USE_FLASH_BBT;
+		this->bbt_options |= NAND_BBT_USE_FLASH;
 	}
 
 	init_completion(&host->op_completion);
@@ -1231,16 +1226,8 @@ static int __init mxcnd_probe(struct platform_device *pdev)
 	}
 
 	/* Register the partitions */
-	nr_parts =
-	    parse_mtd_partitions(mtd, part_probes, &host->parts, 0);
-	if (nr_parts > 0)
-		mtd_device_register(mtd, host->parts, nr_parts);
-	else if (pdata->parts)
-		mtd_device_register(mtd, pdata->parts, pdata->nr_parts);
-	else {
-		pr_info("Registering %s as whole device\n", mtd->name);
-		mtd_device_register(mtd, NULL, 0);
-	}
+	mtd_device_parse_register(mtd, part_probes, 0,
+			pdata->parts, pdata->nr_parts);
 
 	platform_set_drvdata(pdev, host);
 
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index a46e9bb847bd..3ed9c5e4d34e 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -21,7 +21,7 @@
  *  TODO:
  *	Enable cached programming for 2k page size chips
  *	Check, if mtd->ecctype should be set to MTD_ECC_HW
- *	if we have HW ecc support.
+ *	if we have HW ECC support.
  *	The AG-AND chips have nice features for speed improvement,
  *	which are not supported yet. Read / program 4 pages in one go.
  *	BBT table is not serialized, has to be fixed
@@ -113,21 +113,19 @@ static int check_offs_len(struct mtd_info *mtd,
 
 	/* Start address must align on block boundary */
 	if (ofs & ((1 << chip->phys_erase_shift) - 1)) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Unaligned address\n", __func__);
+		pr_debug("%s: unaligned address\n", __func__);
 		ret = -EINVAL;
 	}
 
 	/* Length must align on block boundary */
 	if (len & ((1 << chip->phys_erase_shift) - 1)) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Length not block aligned\n",
-					__func__);
+		pr_debug("%s: length not block aligned\n", __func__);
 		ret = -EINVAL;
 	}
 
 	/* Do not allow past end of device */
 	if (ofs + len > mtd->size) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Past end of device\n",
-					__func__);
+		pr_debug("%s: past end of device\n", __func__);
 		ret = -EINVAL;
 	}
 
@@ -136,9 +134,9 @@ static int check_offs_len(struct mtd_info *mtd,
 
 /**
  * nand_release_device - [GENERIC] release chip
- * @mtd:	MTD device structure
+ * @mtd: MTD device structure
  *
- * Deselect, release chip lock and wake up anyone waiting on the device
+ * Deselect, release chip lock and wake up anyone waiting on the device.
  */
 static void nand_release_device(struct mtd_info *mtd)
 {
@@ -157,9 +155,9 @@ static void nand_release_device(struct mtd_info *mtd)
 
 /**
  * nand_read_byte - [DEFAULT] read one byte from the chip
- * @mtd:	MTD device structure
+ * @mtd: MTD device structure
  *
- * Default read function for 8bit buswith
+ * Default read function for 8bit buswidth
  */
 static uint8_t nand_read_byte(struct mtd_info *mtd)
 {
@@ -169,10 +167,11 @@ static uint8_t nand_read_byte(struct mtd_info *mtd)
 
 /**
  * nand_read_byte16 - [DEFAULT] read one byte endianess aware from the chip
- * @mtd:	MTD device structure
+ * nand_read_byte16 - [DEFAULT] read one byte endianness aware from the chip
+ * @mtd: MTD device structure
+ *
+ * Default read function for 16bit buswidth with endianness conversion.
  *
- * Default read function for 16bit buswith with
- * endianess conversion
  */
 static uint8_t nand_read_byte16(struct mtd_info *mtd)
 {
@@ -182,10 +181,9 @@ static uint8_t nand_read_byte16(struct mtd_info *mtd)
 
 /**
  * nand_read_word - [DEFAULT] read one word from the chip
- * @mtd:	MTD device structure
+ * @mtd: MTD device structure
  *
- * Default read function for 16bit buswith without
- * endianess conversion
+ * Default read function for 16bit buswidth without endianness conversion.
  */
 static u16 nand_read_word(struct mtd_info *mtd)
 {
@@ -195,8 +193,8 @@ static u16 nand_read_word(struct mtd_info *mtd)
 
 /**
  * nand_select_chip - [DEFAULT] control CE line
- * @mtd:	MTD device structure
- * @chipnr:	chipnumber to select, -1 for deselect
+ * @mtd: MTD device structure
+ * @chipnr: chipnumber to select, -1 for deselect
  *
  * Default select function for 1 chip devices.
  */
@@ -218,11 +216,11 @@ static void nand_select_chip(struct mtd_info *mtd, int chipnr)
 
 /**
  * nand_write_buf - [DEFAULT] write buffer to chip
- * @mtd:	MTD device structure
- * @buf:	data buffer
- * @len:	number of bytes to write
+ * @mtd: MTD device structure
+ * @buf: data buffer
+ * @len: number of bytes to write
  *
- * Default write function for 8bit buswith
+ * Default write function for 8bit buswidth.
  */
 static void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
 {
@@ -235,11 +233,11 @@ static void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
 
 /**
  * nand_read_buf - [DEFAULT] read chip data into buffer
- * @mtd:	MTD device structure
- * @buf:	buffer to store date
- * @len:	number of bytes to read
+ * @mtd: MTD device structure
+ * @buf: buffer to store date
+ * @len: number of bytes to read
  *
- * Default read function for 8bit buswith
+ * Default read function for 8bit buswidth.
  */
 static void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
 {
@@ -252,11 +250,11 @@ static void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
 
 /**
  * nand_verify_buf - [DEFAULT] Verify chip data against buffer
- * @mtd:	MTD device structure
- * @buf:	buffer containing the data to compare
- * @len:	number of bytes to compare
+ * @mtd: MTD device structure
+ * @buf: buffer containing the data to compare
+ * @len: number of bytes to compare
  *
- * Default verify function for 8bit buswith
+ * Default verify function for 8bit buswidth.
  */
 static int nand_verify_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
 {
@@ -271,11 +269,11 @@ static int nand_verify_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
 
 /**
  * nand_write_buf16 - [DEFAULT] write buffer to chip
- * @mtd:	MTD device structure
- * @buf:	data buffer
- * @len:	number of bytes to write
+ * @mtd: MTD device structure
+ * @buf: data buffer
+ * @len: number of bytes to write
  *
- * Default write function for 16bit buswith
+ * Default write function for 16bit buswidth.
  */
 static void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
 {
@@ -291,11 +289,11 @@ static void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
 
 /**
  * nand_read_buf16 - [DEFAULT] read chip data into buffer
- * @mtd:	MTD device structure
- * @buf:	buffer to store date
- * @len:	number of bytes to read
+ * @mtd: MTD device structure
+ * @buf: buffer to store date
+ * @len: number of bytes to read
  *
- * Default read function for 16bit buswith
+ * Default read function for 16bit buswidth.
  */
 static void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
 {
@@ -310,11 +308,11 @@ static void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
 
 /**
  * nand_verify_buf16 - [DEFAULT] Verify chip data against buffer
- * @mtd:	MTD device structure
- * @buf:	buffer containing the data to compare
- * @len:	number of bytes to compare
+ * @mtd: MTD device structure
+ * @buf: buffer containing the data to compare
+ * @len: number of bytes to compare
  *
- * Default verify function for 16bit buswith
+ * Default verify function for 16bit buswidth.
  */
 static int nand_verify_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
 {
@@ -332,9 +330,9 @@ static int nand_verify_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
 
 /**
  * nand_block_bad - [DEFAULT] Read bad block marker from the chip
- * @mtd:	MTD device structure
- * @ofs:	offset from device start
- * @getchip:	0, if the chip is already selected
+ * @mtd: MTD device structure
+ * @ofs: offset from device start
+ * @getchip: 0, if the chip is already selected
  *
  * Check, if the block is bad.
  */
@@ -344,7 +342,7 @@ static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip)
 	struct nand_chip *chip = mtd->priv;
 	u16 bad;
 
-	if (chip->options & NAND_BBT_SCANLASTPAGE)
+	if (chip->bbt_options & NAND_BBT_SCANLASTPAGE)
 		ofs += mtd->erasesize - mtd->writesize;
 
 	page = (int)(ofs >> chip->page_shift) & chip->pagemask;
@@ -384,11 +382,11 @@ static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip)
 
 /**
  * nand_default_block_markbad - [DEFAULT] mark a block bad
- * @mtd:	MTD device structure
- * @ofs:	offset from device start
+ * @mtd: MTD device structure
+ * @ofs: offset from device start
  *
- * This is the default implementation, which can be overridden by
- * a hardware specific driver.
+ * This is the default implementation, which can be overridden by a hardware
+ * specific driver.
 */
 static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
 {
@@ -396,7 +394,7 @@ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
 	uint8_t buf[2] = { 0, 0 };
 	int block, ret, i = 0;
 
-	if (chip->options & NAND_BBT_SCANLASTPAGE)
+	if (chip->bbt_options & NAND_BBT_SCANLASTPAGE)
 		ofs += mtd->erasesize - mtd->writesize;
 
 	/* Get block number */
@@ -404,33 +402,31 @@ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
 	if (chip->bbt)
 		chip->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1);
 
-	/* Do we have a flash based bad block table ? */
-	if (chip->options & NAND_USE_FLASH_BBT)
+	/* Do we have a flash based bad block table? */
+	if (chip->bbt_options & NAND_BBT_USE_FLASH)
 		ret = nand_update_bbt(mtd, ofs);
 	else {
+		struct mtd_oob_ops ops;
+
 		nand_get_device(chip, mtd, FL_WRITING);
 
-		/* Write to first two pages and to byte 1 and 6 if necessary.
-		 * If we write to more than one location, the first error
-		 * encountered quits the procedure. We write two bytes per
-		 * location, so we dont have to mess with 16 bit access.
+		/*
+		 * Write to first two pages if necessary. If we write to more
+		 * than one location, the first error encountered quits the
+		 * procedure. We write two bytes per location, so we dont have
+		 * to mess with 16 bit access.
 		 */
+		ops.len = ops.ooblen = 2;
+		ops.datbuf = NULL;
+		ops.oobbuf = buf;
+		ops.ooboffs = chip->badblockpos & ~0x01;
+		ops.mode = MTD_OPS_PLACE_OOB;
 		do {
-			chip->ops.len = chip->ops.ooblen = 2;
-			chip->ops.datbuf = NULL;
-			chip->ops.oobbuf = buf;
-			chip->ops.ooboffs = chip->badblockpos & ~0x01;
-
-			ret = nand_do_write_oob(mtd, ofs, &chip->ops);
+			ret = nand_do_write_oob(mtd, ofs, &ops);
 
-			if (!ret && (chip->options & NAND_BBT_SCANBYTE1AND6)) {
-				chip->ops.ooboffs = NAND_SMALL_BADBLOCK_POS
-					& ~0x01;
-				ret = nand_do_write_oob(mtd, ofs, &chip->ops);
-			}
 			i++;
 			ofs += mtd->writesize;
-		} while (!ret && (chip->options & NAND_BBT_SCAN2NDPAGE) &&
+		} while (!ret && (chip->bbt_options & NAND_BBT_SCAN2NDPAGE) &&
 				i < 2);
 
 		nand_release_device(mtd);
@@ -443,16 +439,16 @@ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
 
 /**
  * nand_check_wp - [GENERIC] check if the chip is write protected
- * @mtd:	MTD device structure
- * Check, if the device is write protected
+ * @mtd: MTD device structure
  *
- * The function expects, that the device is already selected
+ * Check, if the device is write protected. The function expects, that the
+ * device is already selected.
  */
 static int nand_check_wp(struct mtd_info *mtd)
 {
 	struct nand_chip *chip = mtd->priv;
 
-	/* broken xD cards report WP despite being writable */
+	/* Broken xD cards report WP despite being writable */
 	if (chip->options & NAND_BROKEN_XD)
 		return 0;
 
@@ -463,10 +459,10 @@ static int nand_check_wp(struct mtd_info *mtd)
 
 /**
  * nand_block_checkbad - [GENERIC] Check if a block is marked bad
- * @mtd:	MTD device structure
- * @ofs:	offset from device start
- * @getchip:	0, if the chip is already selected
- * @allowbbt:	1, if its allowed to access the bbt area
+ * @mtd: MTD device structure
+ * @ofs: offset from device start
+ * @getchip: 0, if the chip is already selected
+ * @allowbbt: 1, if its allowed to access the bbt area
  *
  * Check, if the block is bad. Either by reading the bad block table or
  * calling of the scan function.
@@ -485,8 +481,8 @@ static int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int getchip,
 
 /**
  * panic_nand_wait_ready - [GENERIC] Wait for the ready pin after commands.
- * @mtd:	MTD device structure
- * @timeo:	Timeout
+ * @mtd: MTD device structure
+ * @timeo: Timeout
  *
  * Helper function for nand_wait_ready used when needing to wait in interrupt
  * context.
@@ -505,10 +501,7 @@ static void panic_nand_wait_ready(struct mtd_info *mtd, unsigned long timeo)
 	}
 }
 
-/*
- * Wait for the ready pin, after a command
- * The timeout is catched later.
- */
+/* Wait for the ready pin, after a command. The timeout is caught later. */
 void nand_wait_ready(struct mtd_info *mtd)
 {
 	struct nand_chip *chip = mtd->priv;
@@ -519,7 +512,7 @@ void nand_wait_ready(struct mtd_info *mtd)
 		return panic_nand_wait_ready(mtd, 400);
 
 	led_trigger_event(nand_led_trigger, LED_FULL);
-	/* wait until command is processed or timeout occures */
+	/* Wait until command is processed or timeout occurs */
 	do {
 		if (chip->dev_ready(mtd))
 			break;
@@ -531,13 +524,13 @@ EXPORT_SYMBOL_GPL(nand_wait_ready);
 
 /**
  * nand_command - [DEFAULT] Send command to NAND device
- * @mtd:	MTD device structure
- * @command:	the command to be sent
- * @column:	the column address for this command, -1 if none
- * @page_addr:	the page address for this command, -1 if none
+ * @mtd: MTD device structure
+ * @command: the command to be sent
+ * @column: the column address for this command, -1 if none
+ * @page_addr: the page address for this command, -1 if none
  *
- * Send command to NAND device. This function is used for small page
- * devices (256/512 Bytes per page)
+ * Send command to NAND device. This function is used for small page devices
+ * (256/512 Bytes per page).
  */
 static void nand_command(struct mtd_info *mtd, unsigned int command,
 			 int column, int page_addr)
@@ -545,9 +538,7 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
 	register struct nand_chip *chip = mtd->priv;
 	int ctrl = NAND_CTRL_CLE | NAND_CTRL_CHANGE;
 
-	/*
-	 * Write out the command to the device.
-	 */
+	/* Write out the command to the device */
 	if (command == NAND_CMD_SEQIN) {
 		int readcmd;
 
@@ -567,9 +558,7 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
 	}
 	chip->cmd_ctrl(mtd, command, ctrl);
 
-	/*
-	 * Address cycle, when necessary
-	 */
+	/* Address cycle, when necessary */
 	ctrl = NAND_CTRL_ALE | NAND_CTRL_CHANGE;
 	/* Serially input address */
 	if (column != -1) {
@@ -590,8 +579,8 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
 	chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
 
 	/*
-	 * program and erase have their own busy handlers
-	 * status and sequential in needs no delay
+	 * Program and erase have their own busy handlers status and sequential
+	 * in needs no delay
 	 */
 	switch (command) {
 
@@ -625,8 +614,10 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
 			return;
 		}
 	}
-	/* Apply this short delay always to ensure that we do wait tWB in
-	 * any case on any machine. */
+	/*
+	 * Apply this short delay always to ensure that we do wait tWB in
+	 * any case on any machine.
+	 */
 	ndelay(100);
 
 	nand_wait_ready(mtd);
@@ -634,14 +625,14 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
 
 /**
  * nand_command_lp - [DEFAULT] Send command to NAND large page device
- * @mtd:	MTD device structure
- * @command:	the command to be sent
- * @column:	the column address for this command, -1 if none
- * @page_addr:	the page address for this command, -1 if none
+ * @mtd: MTD device structure
+ * @command: the command to be sent
+ * @column: the column address for this command, -1 if none
+ * @page_addr: the page address for this command, -1 if none
  *
  * Send command to NAND device. This is the version for the new large page
- * devices We dont have the separate regions as we have in the small page
- * devices.  We must emulate NAND_CMD_READOOB to keep the code compatible.
+ * devices. We don't have the separate regions as we have in the small page
+ * devices. We must emulate NAND_CMD_READOOB to keep the code compatible.
  */
 static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
 			    int column, int page_addr)
@@ -683,8 +674,8 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
 	chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
 
 	/*
-	 * program and erase have their own busy handlers
-	 * status, sequential in, and deplete1 need no delay
+	 * Program and erase have their own busy handlers status, sequential
+	 * in, and deplete1 need no delay.
 	 */
 	switch (command) {
 
@@ -698,14 +689,12 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
 	case NAND_CMD_DEPLETE1:
 		return;
 
-		/*
-		 * read error status commands require only a short delay
-		 */
 	case NAND_CMD_STATUS_ERROR:
 	case NAND_CMD_STATUS_ERROR0:
 	case NAND_CMD_STATUS_ERROR1:
 	case NAND_CMD_STATUS_ERROR2:
 	case NAND_CMD_STATUS_ERROR3:
+		/* Read error status commands require only a short delay */
 		udelay(chip->chip_delay);
 		return;
 
@@ -739,7 +728,7 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
 	default:
 		/*
 		 * If we don't have access to the busy pin, we apply the given
-		 * command delay
+		 * command delay.
 		 */
 		if (!chip->dev_ready) {
 			udelay(chip->chip_delay);
@@ -747,8 +736,10 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
 		}
 	}
 
-	/* Apply this short delay always to ensure that we do wait tWB in
-	 * any case on any machine. */
+	/*
+	 * Apply this short delay always to ensure that we do wait tWB in
+	 * any case on any machine.
+	 */
 	ndelay(100);
 
 	nand_wait_ready(mtd);
@@ -756,25 +747,25 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
 
 /**
  * panic_nand_get_device - [GENERIC] Get chip for selected access
- * @chip:	the nand chip descriptor
- * @mtd:	MTD device structure
- * @new_state:	the state which is requested
+ * @chip: the nand chip descriptor
+ * @mtd: MTD device structure
+ * @new_state: the state which is requested
  *
  * Used when in panic, no locks are taken.
  */
 static void panic_nand_get_device(struct nand_chip *chip,
 		      struct mtd_info *mtd, int new_state)
 {
-	/* Hardware controller shared among independend devices */
+	/* Hardware controller shared among independent devices */
 	chip->controller->active = chip;
 	chip->state = new_state;
 }
 
 /**
  * nand_get_device - [GENERIC] Get chip for selected access
- * @chip:	the nand chip descriptor
- * @mtd:	MTD device structure
- * @new_state:	the state which is requested
+ * @chip: the nand chip descriptor
+ * @mtd: MTD device structure
+ * @new_state: the state which is requested
  *
  * Get the device and lock it for exclusive access
  */
@@ -812,10 +803,10 @@ retry:
 }
 
 /**
- * panic_nand_wait - [GENERIC]  wait until the command is done
- * @mtd:	MTD device structure
- * @chip:	NAND chip structure
- * @timeo:	Timeout
+ * panic_nand_wait - [GENERIC] wait until the command is done
+ * @mtd: MTD device structure
+ * @chip: NAND chip structure
+ * @timeo: timeout
  *
  * Wait for command done. This is a helper function for nand_wait used when
  * we are in interrupt context. May happen when in panic and trying to write
@@ -838,13 +829,13 @@ static void panic_nand_wait(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_wait - [DEFAULT]  wait until the command is done
- * @mtd:	MTD device structure
- * @chip:	NAND chip structure
+ * nand_wait - [DEFAULT] wait until the command is done
+ * @mtd: MTD device structure
+ * @chip: NAND chip structure
  *
- * Wait for command done. This applies to erase and program only
- * Erase can take up to 400ms and program up to 20ms according to
- * general NAND and SmartMedia specs
+ * Wait for command done. This applies to erase and program only. Erase can
+ * take up to 400ms and program up to 20ms according to general NAND and
+ * SmartMedia specs.
  */
 static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip)
 {
@@ -859,8 +850,10 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip)
 
 	led_trigger_event(nand_led_trigger, LED_FULL);
 
-	/* Apply this short delay always to ensure that we do wait tWB in
-	 * any case on any machine. */
+	/*
+	 * Apply this short delay always to ensure that we do wait tWB in any
+	 * case on any machine.
+	 */
 	ndelay(100);
 
 	if ((state == FL_ERASING) && (chip->options & NAND_IS_AND))
@@ -890,16 +883,15 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip)
 
 /**
  * __nand_unlock - [REPLACEABLE] unlocks specified locked blocks
- *
  * @mtd: mtd info
  * @ofs: offset to start unlock from
  * @len: length to unlock
- * @invert:   when = 0, unlock the range of blocks within the lower and
- *                      upper boundary address
- *            when = 1, unlock the range of blocks outside the boundaries
- *                      of the lower and upper boundary address
+ * @invert: when = 0, unlock the range of blocks within the lower and
+ *                    upper boundary address
+ *          when = 1, unlock the range of blocks outside the boundaries
+ *                    of the lower and upper boundary address
  *
- * return - unlock status
+ * Returs unlock status.
  */
 static int __nand_unlock(struct mtd_info *mtd, loff_t ofs,
 					uint64_t len, int invert)
@@ -919,10 +911,9 @@ static int __nand_unlock(struct mtd_info *mtd, loff_t ofs,
 
 	/* Call wait ready function */
 	status = chip->waitfunc(mtd, chip);
-	udelay(1000);
 	/* See if device thinks it succeeded */
 	if (status & 0x01) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Error status = 0x%08x\n",
+		pr_debug("%s: error status = 0x%08x\n",
 					__func__, status);
 		ret = -EIO;
 	}
@@ -932,12 +923,11 @@ static int __nand_unlock(struct mtd_info *mtd, loff_t ofs,
 
 /**
  * nand_unlock - [REPLACEABLE] unlocks specified locked blocks
- *
  * @mtd: mtd info
  * @ofs: offset to start unlock from
  * @len: length to unlock
  *
- * return - unlock status
+ * Returns unlock status.
  */
 int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 {
@@ -945,7 +935,7 @@ int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 	int chipnr;
 	struct nand_chip *chip = mtd->priv;
 
-	DEBUG(MTD_DEBUG_LEVEL3, "%s: start = 0x%012llx, len = %llu\n",
+	pr_debug("%s: start = 0x%012llx, len = %llu\n",
 			__func__, (unsigned long long)ofs, len);
 
 	if (check_offs_len(mtd, ofs, len))
@@ -964,7 +954,7 @@ int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 
 	/* Check, if it is write protected */
 	if (nand_check_wp(mtd)) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Device is write protected!!!\n",
+		pr_debug("%s: device is write protected!\n",
 					__func__);
 		ret = -EIO;
 		goto out;
@@ -981,18 +971,16 @@ EXPORT_SYMBOL(nand_unlock);
 
 /**
  * nand_lock - [REPLACEABLE] locks all blocks present in the device
- *
  * @mtd: mtd info
  * @ofs: offset to start unlock from
  * @len: length to unlock
  *
- * return - lock status
+ * This feature is not supported in many NAND parts. 'Micron' NAND parts do
+ * have this feature, but it allows only to lock all blocks, not for specified
+ * range for block. Implementing 'lock' feature by making use of 'unlock', for
+ * now.
  *
- * This feature is not supported in many NAND parts. 'Micron' NAND parts
- * do have this feature, but it allows only to lock all blocks, not for
- * specified range for block.
- *
- * Implementing 'lock' feature by making use of 'unlock', for now.
+ * Returns lock status.
  */
 int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 {
@@ -1000,7 +988,7 @@ int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 	int chipnr, status, page;
 	struct nand_chip *chip = mtd->priv;
 
-	DEBUG(MTD_DEBUG_LEVEL3, "%s: start = 0x%012llx, len = %llu\n",
+	pr_debug("%s: start = 0x%012llx, len = %llu\n",
 			__func__, (unsigned long long)ofs, len);
 
 	if (check_offs_len(mtd, ofs, len))
@@ -1015,7 +1003,7 @@ int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 
 	/* Check, if it is write protected */
 	if (nand_check_wp(mtd)) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Device is write protected!!!\n",
+		pr_debug("%s: device is write protected!\n",
 					__func__);
 		status = MTD_ERASE_FAILED;
 		ret = -EIO;
@@ -1028,10 +1016,9 @@ int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 
 	/* Call wait ready function */
 	status = chip->waitfunc(mtd, chip);
-	udelay(1000);
 	/* See if device thinks it succeeded */
 	if (status & 0x01) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Error status = 0x%08x\n",
+		pr_debug("%s: error status = 0x%08x\n",
 					__func__, status);
 		ret = -EIO;
 		goto out;
@@ -1047,13 +1034,13 @@ out:
 EXPORT_SYMBOL(nand_lock);
 
 /**
- * nand_read_page_raw - [Intern] read raw page data without ecc
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @buf:	buffer to store read data
- * @page:	page number to read
+ * nand_read_page_raw - [INTERN] read raw page data without ecc
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @page: page number to read
  *
- * Not for syndrome calculating ecc controllers, which use a special oob layout
+ * Not for syndrome calculating ECC controllers, which use a special oob layout.
  */
 static int nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
 			      uint8_t *buf, int page)
@@ -1064,11 +1051,11 @@ static int nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_read_page_raw_syndrome - [Intern] read raw page data without ecc
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @buf:	buffer to store read data
- * @page:	page number to read
+ * nand_read_page_raw_syndrome - [INTERN] read raw page data without ecc
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @page: page number to read
  *
  * We need a special oob layout and handling even when OOB isn't used.
  */
@@ -1107,11 +1094,11 @@ static int nand_read_page_raw_syndrome(struct mtd_info *mtd,
 }
 
 /**
- * nand_read_page_swecc - [REPLACABLE] software ecc based page read function
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @buf:	buffer to store read data
- * @page:	page number to read
+ * nand_read_page_swecc - [REPLACEABLE] software ECC based page read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @page: page number to read
  */
 static int nand_read_page_swecc(struct mtd_info *mtd, struct nand_chip *chip,
 				uint8_t *buf, int page)
@@ -1148,12 +1135,12 @@ static int nand_read_page_swecc(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_read_subpage - [REPLACABLE] software ecc based sub-page read function
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @data_offs:	offset of requested data within the page
- * @readlen:	data length
- * @bufpoi:	buffer to store read data
+ * nand_read_subpage - [REPLACEABLE] software ECC based sub-page read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @data_offs: offset of requested data within the page
+ * @readlen: data length
+ * @bufpoi: buffer to store read data
  */
 static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip,
 			uint32_t data_offs, uint32_t readlen, uint8_t *bufpoi)
@@ -1166,12 +1153,12 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip,
 	int busw = (chip->options & NAND_BUSWIDTH_16) ? 2 : 1;
 	int index = 0;
 
-	/* Column address wihin the page aligned to ECC size (256bytes). */
+	/* Column address within the page aligned to ECC size (256bytes) */
 	start_step = data_offs / chip->ecc.size;
 	end_step = (data_offs + readlen - 1) / chip->ecc.size;
 	num_steps = end_step - start_step + 1;
 
-	/* Data size aligned to ECC ecc.size*/
+	/* Data size aligned to ECC ecc.size */
 	datafrag_len = num_steps * chip->ecc.size;
 	eccfrag_len = num_steps * chip->ecc.bytes;
 
@@ -1183,13 +1170,14 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip,
 	p = bufpoi + data_col_addr;
 	chip->read_buf(mtd, p, datafrag_len);
 
-	/* Calculate  ECC */
+	/* Calculate ECC */
 	for (i = 0; i < eccfrag_len ; i += chip->ecc.bytes, p += chip->ecc.size)
 		chip->ecc.calculate(mtd, p, &chip->buffers->ecccalc[i]);
 
-	/* The performance is faster if to position offsets
-	   according to ecc.pos. Let make sure here that
-	   there are no gaps in ecc positions */
+	/*
+	 * The performance is faster if we position offsets according to
+	 * ecc.pos. Let's make sure that there are no gaps in ECC positions.
+	 */
 	for (i = 0; i < eccfrag_len - 1; i++) {
 		if (eccpos[i + start_step * chip->ecc.bytes] + 1 !=
 			eccpos[i + start_step * chip->ecc.bytes + 1]) {
@@ -1201,8 +1189,10 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip,
 		chip->cmdfunc(mtd, NAND_CMD_RNDOUT, mtd->writesize, -1);
 		chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
 	} else {
-		/* send the command to read the particular ecc bytes */
-		/* take care about buswidth alignment in read_buf */
+		/*
+		 * Send the command to read the particular ECC bytes take care
+		 * about buswidth alignment in read_buf.
+		 */
 		index = start_step * chip->ecc.bytes;
 
 		aligned_pos = eccpos[index] & ~(busw - 1);
@@ -1235,13 +1225,13 @@ static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_read_page_hwecc - [REPLACABLE] hardware ecc based page read function
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @buf:	buffer to store read data
- * @page:	page number to read
+ * nand_read_page_hwecc - [REPLACEABLE] hardware ECC based page read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @page: page number to read
  *
- * Not for syndrome calculating ecc controllers which need a special oob layout
+ * Not for syndrome calculating ECC controllers which need a special oob layout.
  */
 static int nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
 				uint8_t *buf, int page)
@@ -1280,18 +1270,17 @@ static int nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_read_page_hwecc_oob_first - [REPLACABLE] hw ecc, read oob first
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @buf:	buffer to store read data
- * @page:	page number to read
+ * nand_read_page_hwecc_oob_first - [REPLACEABLE] hw ecc, read oob first
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @page: page number to read
  *
- * Hardware ECC for large page chips, require OOB to be read first.
- * For this ECC mode, the write_page method is re-used from ECC_HW.
- * These methods read/write ECC from the OOB area, unlike the
- * ECC_HW_SYNDROME support with multiple ECC steps, follows the
- * "infix ECC" scheme and reads/writes ECC from the data area, by
- * overwriting the NAND manufacturer bad block markings.
+ * Hardware ECC for large page chips, require OOB to be read first. For this
+ * ECC mode, the write_page method is re-used from ECC_HW. These methods
+ * read/write ECC from the OOB area, unlike the ECC_HW_SYNDROME support with
+ * multiple ECC steps, follows the "infix ECC" scheme and reads/writes ECC from
+ * the data area, by overwriting the NAND manufacturer bad block markings.
  */
 static int nand_read_page_hwecc_oob_first(struct mtd_info *mtd,
 	struct nand_chip *chip, uint8_t *buf, int page)
@@ -1329,14 +1318,14 @@ static int nand_read_page_hwecc_oob_first(struct mtd_info *mtd,
 }
 
 /**
- * nand_read_page_syndrome - [REPLACABLE] hardware ecc syndrom based page read
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @buf:	buffer to store read data
- * @page:	page number to read
+ * nand_read_page_syndrome - [REPLACEABLE] hardware ECC syndrome based page read
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @page: page number to read
  *
- * The hw generator calculates the error syndrome automatically. Therefor
- * we need a special oob layout and handling.
+ * The hw generator calculates the error syndrome automatically. Therefore we
+ * need a special oob layout and handling.
  */
 static int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
 				   uint8_t *buf, int page)
@@ -1384,29 +1373,29 @@ static int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_transfer_oob - [Internal] Transfer oob to client buffer
- * @chip:	nand chip structure
- * @oob:	oob destination address
- * @ops:	oob ops structure
- * @len:	size of oob to transfer
+ * nand_transfer_oob - [INTERN] Transfer oob to client buffer
+ * @chip: nand chip structure
+ * @oob: oob destination address
+ * @ops: oob ops structure
+ * @len: size of oob to transfer
  */
 static uint8_t *nand_transfer_oob(struct nand_chip *chip, uint8_t *oob,
 				  struct mtd_oob_ops *ops, size_t len)
 {
 	switch (ops->mode) {
 
-	case MTD_OOB_PLACE:
-	case MTD_OOB_RAW:
+	case MTD_OPS_PLACE_OOB:
+	case MTD_OPS_RAW:
 		memcpy(oob, chip->oob_poi + ops->ooboffs, len);
 		return oob + len;
 
-	case MTD_OOB_AUTO: {
+	case MTD_OPS_AUTO_OOB: {
 		struct nand_oobfree *free = chip->ecc.layout->oobfree;
 		uint32_t boffs = 0, roffs = ops->ooboffs;
 		size_t bytes = 0;
 
 		for (; free->length && len; free++, len -= bytes) {
-			/* Read request not from offset 0 ? */
+			/* Read request not from offset 0? */
 			if (unlikely(roffs)) {
 				if (roffs >= free->length) {
 					roffs -= free->length;
@@ -1432,11 +1421,10 @@ static uint8_t *nand_transfer_oob(struct nand_chip *chip, uint8_t *oob,
 }
 
 /**
- * nand_do_read_ops - [Internal] Read data with ECC
- *
- * @mtd:	MTD device structure
- * @from:	offset to read from
- * @ops:	oob ops structure
+ * nand_do_read_ops - [INTERN] Read data with ECC
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @ops: oob ops structure
  *
  * Internal function. Called with chip held.
  */
@@ -1451,7 +1439,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
 	int ret = 0;
 	uint32_t readlen = ops->len;
 	uint32_t oobreadlen = ops->ooblen;
-	uint32_t max_oobsize = ops->mode == MTD_OOB_AUTO ?
+	uint32_t max_oobsize = ops->mode == MTD_OPS_AUTO_OOB ?
 		mtd->oobavail : mtd->oobsize;
 
 	uint8_t *bufpoi, *oob, *buf;
@@ -1473,7 +1461,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
 		bytes = min(mtd->writesize - col, readlen);
 		aligned = (bytes == mtd->writesize);
 
-		/* Is the current page in the buffer ? */
+		/* Is the current page in the buffer? */
 		if (realpage != chip->pagebuf || oob) {
 			bufpoi = aligned ? buf : chip->buffers->databuf;
 
@@ -1483,7 +1471,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
 			}
 
 			/* Now read the page into the buffer */
-			if (unlikely(ops->mode == MTD_OOB_RAW))
+			if (unlikely(ops->mode == MTD_OPS_RAW))
 				ret = chip->ecc.read_page_raw(mtd, chip,
 							      bufpoi, page);
 			else if (!aligned && NAND_SUBPAGE_READ(chip) && !oob)
@@ -1492,14 +1480,22 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
 			else
 				ret = chip->ecc.read_page(mtd, chip, bufpoi,
 							  page);
-			if (ret < 0)
+			if (ret < 0) {
+				if (!aligned)
+					/* Invalidate page cache */
+					chip->pagebuf = -1;
 				break;
+			}
 
 			/* Transfer not aligned data */
 			if (!aligned) {
 				if (!NAND_SUBPAGE_READ(chip) && !oob &&
-				    !(mtd->ecc_stats.failed - stats.failed))
+				    !(mtd->ecc_stats.failed - stats.failed) &&
+				    (ops->mode != MTD_OPS_RAW))
 					chip->pagebuf = realpage;
+				else
+					/* Invalidate page cache */
+					chip->pagebuf = -1;
 				memcpy(buf, chip->buffers->databuf + col, bytes);
 			}
 
@@ -1539,7 +1535,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
 		if (!readlen)
 			break;
 
-		/* For subsequent reads align to page boundary. */
+		/* For subsequent reads align to page boundary */
 		col = 0;
 		/* Increment page address */
 		realpage++;
@@ -1552,8 +1548,9 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
 			chip->select_chip(mtd, chipnr);
 		}
 
-		/* Check, if the chip supports auto page increment
-		 * or if we have hit a block boundary.
+		/*
+		 * Check, if the chip supports auto page increment or if we
+		 * have hit a block boundary.
 		 */
 		if (!NAND_CANAUTOINCR(chip) || !(page & blkcheck))
 			sndcmd = 1;
@@ -1574,18 +1571,19 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
 
 /**
  * nand_read - [MTD Interface] MTD compatibility function for nand_do_read_ecc
- * @mtd:	MTD device structure
- * @from:	offset to read from
- * @len:	number of bytes to read
- * @retlen:	pointer to variable to store the number of read bytes
- * @buf:	the databuffer to put data
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @len: number of bytes to read
+ * @retlen: pointer to variable to store the number of read bytes
+ * @buf: the databuffer to put data
  *
- * Get hold of the chip and call nand_do_read
+ * Get hold of the chip and call nand_do_read.
  */
 static int nand_read(struct mtd_info *mtd, loff_t from, size_t len,
 		     size_t *retlen, uint8_t *buf)
 {
 	struct nand_chip *chip = mtd->priv;
+	struct mtd_oob_ops ops;
 	int ret;
 
 	/* Do not allow reads past end of device */
@@ -1596,13 +1594,14 @@ static int nand_read(struct mtd_info *mtd, loff_t from, size_t len,
 
 	nand_get_device(chip, mtd, FL_READING);
 
-	chip->ops.len = len;
-	chip->ops.datbuf = buf;
-	chip->ops.oobbuf = NULL;
+	ops.len = len;
+	ops.datbuf = buf;
+	ops.oobbuf = NULL;
+	ops.mode = 0;
 
-	ret = nand_do_read_ops(mtd, from, &chip->ops);
+	ret = nand_do_read_ops(mtd, from, &ops);
 
-	*retlen = chip->ops.retlen;
+	*retlen = ops.retlen;
 
 	nand_release_device(mtd);
 
@@ -1610,11 +1609,11 @@ static int nand_read(struct mtd_info *mtd, loff_t from, size_t len,
 }
 
 /**
- * nand_read_oob_std - [REPLACABLE] the most common OOB data read function
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @page:	page number to read
- * @sndcmd:	flag whether to issue read command or not
+ * nand_read_oob_std - [REPLACEABLE] the most common OOB data read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @page: page number to read
+ * @sndcmd: flag whether to issue read command or not
  */
 static int nand_read_oob_std(struct mtd_info *mtd, struct nand_chip *chip,
 			     int page, int sndcmd)
@@ -1628,12 +1627,12 @@ static int nand_read_oob_std(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_read_oob_syndrome - [REPLACABLE] OOB data read function for HW ECC
+ * nand_read_oob_syndrome - [REPLACEABLE] OOB data read function for HW ECC
  *			    with syndromes
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @page:	page number to read
- * @sndcmd:	flag whether to issue read command or not
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @page: page number to read
+ * @sndcmd: flag whether to issue read command or not
  */
 static int nand_read_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
 				  int page, int sndcmd)
@@ -1667,10 +1666,10 @@ static int nand_read_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_write_oob_std - [REPLACABLE] the most common OOB data write function
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @page:	page number to write
+ * nand_write_oob_std - [REPLACEABLE] the most common OOB data write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @page: page number to write
  */
 static int nand_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip,
 			      int page)
@@ -1690,11 +1689,11 @@ static int nand_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_write_oob_syndrome - [REPLACABLE] OOB data write function for HW ECC
- *			     with syndrome - only for large page flash !
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @page:	page number to write
+ * nand_write_oob_syndrome - [REPLACEABLE] OOB data write function for HW ECC
+ *			     with syndrome - only for large page flash
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @page: page number to write
  */
 static int nand_write_oob_syndrome(struct mtd_info *mtd,
 				   struct nand_chip *chip, int page)
@@ -1749,34 +1748,37 @@ static int nand_write_oob_syndrome(struct mtd_info *mtd,
 }
 
 /**
- * nand_do_read_oob - [Intern] NAND read out-of-band
- * @mtd:	MTD device structure
- * @from:	offset to read from
- * @ops:	oob operations description structure
+ * nand_do_read_oob - [INTERN] NAND read out-of-band
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @ops: oob operations description structure
  *
- * NAND read out-of-band data from the spare area
+ * NAND read out-of-band data from the spare area.
  */
 static int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
 			    struct mtd_oob_ops *ops)
 {
 	int page, realpage, chipnr, sndcmd = 1;
 	struct nand_chip *chip = mtd->priv;
+	struct mtd_ecc_stats stats;
 	int blkcheck = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1;
 	int readlen = ops->ooblen;
 	int len;
 	uint8_t *buf = ops->oobbuf;
 
-	DEBUG(MTD_DEBUG_LEVEL3, "%s: from = 0x%08Lx, len = %i\n",
+	pr_debug("%s: from = 0x%08Lx, len = %i\n",
 			__func__, (unsigned long long)from, readlen);
 
-	if (ops->mode == MTD_OOB_AUTO)
+	stats = mtd->ecc_stats;
+
+	if (ops->mode == MTD_OPS_AUTO_OOB)
 		len = chip->ecc.layout->oobavail;
 	else
 		len = mtd->oobsize;
 
 	if (unlikely(ops->ooboffs >= len)) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt to start read "
-					"outside oob\n", __func__);
+		pr_debug("%s: attempt to start read outside oob\n",
+				__func__);
 		return -EINVAL;
 	}
 
@@ -1784,8 +1786,8 @@ static int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
 	if (unlikely(from >= mtd->size ||
 		     ops->ooboffs + readlen > ((mtd->size >> chip->page_shift) -
 					(from >> chip->page_shift)) * len)) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt read beyond end "
-					"of device\n", __func__);
+		pr_debug("%s: attempt to read beyond end of device\n",
+				__func__);
 		return -EINVAL;
 	}
 
@@ -1797,7 +1799,10 @@ static int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
 	page = realpage & chip->pagemask;
 
 	while (1) {
-		sndcmd = chip->ecc.read_oob(mtd, chip, page, sndcmd);
+		if (ops->mode == MTD_OPS_RAW)
+			sndcmd = chip->ecc.read_oob_raw(mtd, chip, page, sndcmd);
+		else
+			sndcmd = chip->ecc.read_oob(mtd, chip, page, sndcmd);
 
 		len = min(len, readlen);
 		buf = nand_transfer_oob(chip, buf, ops, len);
@@ -1830,24 +1835,29 @@ static int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
 			chip->select_chip(mtd, chipnr);
 		}
 
-		/* Check, if the chip supports auto page increment
-		 * or if we have hit a block boundary.
+		/*
+		 * Check, if the chip supports auto page increment or if we
+		 * have hit a block boundary.
 		 */
 		if (!NAND_CANAUTOINCR(chip) || !(page & blkcheck))
 			sndcmd = 1;
 	}
 
 	ops->oobretlen = ops->ooblen;
-	return 0;
+
+	if (mtd->ecc_stats.failed - stats.failed)
+		return -EBADMSG;
+
+	return  mtd->ecc_stats.corrected - stats.corrected ? -EUCLEAN : 0;
 }
 
 /**
  * nand_read_oob - [MTD Interface] NAND read data and/or out-of-band
- * @mtd:	MTD device structure
- * @from:	offset to read from
- * @ops:	oob operation description structure
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @ops: oob operation description structure
  *
- * NAND read data and/or out-of-band data
+ * NAND read data and/or out-of-band data.
  */
 static int nand_read_oob(struct mtd_info *mtd, loff_t from,
 			 struct mtd_oob_ops *ops)
@@ -1859,17 +1869,17 @@ static int nand_read_oob(struct mtd_info *mtd, loff_t from,
 
 	/* Do not allow reads past end of device */
 	if (ops->datbuf && (from + ops->len) > mtd->size) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt read "
-				"beyond end of device\n", __func__);
+		pr_debug("%s: attempt to read beyond end of device\n",
+				__func__);
 		return -EINVAL;
 	}
 
 	nand_get_device(chip, mtd, FL_READING);
 
 	switch (ops->mode) {
-	case MTD_OOB_PLACE:
-	case MTD_OOB_AUTO:
-	case MTD_OOB_RAW:
+	case MTD_OPS_PLACE_OOB:
+	case MTD_OPS_AUTO_OOB:
+	case MTD_OPS_RAW:
 		break;
 
 	default:
@@ -1888,12 +1898,12 @@ out:
 
 
 /**
- * nand_write_page_raw - [Intern] raw page write function
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @buf:	data buffer
+ * nand_write_page_raw - [INTERN] raw page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
  *
- * Not for syndrome calculating ecc controllers, which use a special oob layout
+ * Not for syndrome calculating ECC controllers, which use a special oob layout.
  */
 static void nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
 				const uint8_t *buf)
@@ -1903,10 +1913,10 @@ static void nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_write_page_raw_syndrome - [Intern] raw page write function
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @buf:	data buffer
+ * nand_write_page_raw_syndrome - [INTERN] raw page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
  *
  * We need a special oob layout and handling even when ECC isn't checked.
  */
@@ -1942,10 +1952,10 @@ static void nand_write_page_raw_syndrome(struct mtd_info *mtd,
 		chip->write_buf(mtd, oob, size);
 }
 /**
- * nand_write_page_swecc - [REPLACABLE] software ecc based page write function
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @buf:	data buffer
+ * nand_write_page_swecc - [REPLACEABLE] software ECC based page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
  */
 static void nand_write_page_swecc(struct mtd_info *mtd, struct nand_chip *chip,
 				  const uint8_t *buf)
@@ -1957,7 +1967,7 @@ static void nand_write_page_swecc(struct mtd_info *mtd, struct nand_chip *chip,
 	const uint8_t *p = buf;
 	uint32_t *eccpos = chip->ecc.layout->eccpos;
 
-	/* Software ecc calculation */
+	/* Software ECC calculation */
 	for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize)
 		chip->ecc.calculate(mtd, p, &ecc_calc[i]);
 
@@ -1968,10 +1978,10 @@ static void nand_write_page_swecc(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_write_page_hwecc - [REPLACABLE] hardware ecc based page write function
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @buf:	data buffer
+ * nand_write_page_hwecc - [REPLACEABLE] hardware ECC based page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
  */
 static void nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
 				  const uint8_t *buf)
@@ -1996,13 +2006,13 @@ static void nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_write_page_syndrome - [REPLACABLE] hardware ecc syndrom based page write
- * @mtd:	mtd info structure
- * @chip:	nand chip info structure
- * @buf:	data buffer
+ * nand_write_page_syndrome - [REPLACEABLE] hardware ECC syndrome based page write
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
  *
- * The hw generator calculates the error syndrome automatically. Therefor
- * we need a special oob layout and handling.
+ * The hw generator calculates the error syndrome automatically. Therefore we
+ * need a special oob layout and handling.
  */
 static void nand_write_page_syndrome(struct mtd_info *mtd,
 				    struct nand_chip *chip, const uint8_t *buf)
@@ -2041,12 +2051,12 @@ static void nand_write_page_syndrome(struct mtd_info *mtd,
 
 /**
  * nand_write_page - [REPLACEABLE] write one page
- * @mtd:	MTD device structure
- * @chip:	NAND chip descriptor
- * @buf:	the data to write
- * @page:	page number to write
- * @cached:	cached programming
- * @raw:	use _raw version of write_page
+ * @mtd: MTD device structure
+ * @chip: NAND chip descriptor
+ * @buf: the data to write
+ * @page: page number to write
+ * @cached: cached programming
+ * @raw: use _raw version of write_page
  */
 static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip,
 			   const uint8_t *buf, int page, int cached, int raw)
@@ -2061,8 +2071,8 @@ static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip,
 		chip->ecc.write_page(mtd, chip, buf);
 
 	/*
-	 * Cached progamming disabled for now, Not sure if its worth the
-	 * trouble. The speed gain is not very impressive. (2.3->2.6Mib/s)
+	 * Cached progamming disabled for now. Not sure if it's worth the
+	 * trouble. The speed gain is not very impressive. (2.3->2.6Mib/s).
 	 */
 	cached = 0;
 
@@ -2072,7 +2082,7 @@ static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip,
 		status = chip->waitfunc(mtd, chip);
 		/*
 		 * See if operation failed and additional status checks are
-		 * available
+		 * available.
 		 */
 		if ((status & NAND_STATUS_FAIL) && (chip->errstat))
 			status = chip->errstat(mtd, chip, FL_WRITING, status,
@@ -2096,29 +2106,37 @@ static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /**
- * nand_fill_oob - [Internal] Transfer client buffer to oob
- * @chip:	nand chip structure
- * @oob:	oob data buffer
- * @len:	oob data write length
- * @ops:	oob ops structure
+ * nand_fill_oob - [INTERN] Transfer client buffer to oob
+ * @mtd: MTD device structure
+ * @oob: oob data buffer
+ * @len: oob data write length
+ * @ops: oob ops structure
  */
-static uint8_t *nand_fill_oob(struct nand_chip *chip, uint8_t *oob, size_t len,
-						struct mtd_oob_ops *ops)
+static uint8_t *nand_fill_oob(struct mtd_info *mtd, uint8_t *oob, size_t len,
+			      struct mtd_oob_ops *ops)
 {
+	struct nand_chip *chip = mtd->priv;
+
+	/*
+	 * Initialise to all 0xFF, to avoid the possibility of left over OOB
+	 * data from a previous OOB read.
+	 */
+	memset(chip->oob_poi, 0xff, mtd->oobsize);
+
 	switch (ops->mode) {
 
-	case MTD_OOB_PLACE:
-	case MTD_OOB_RAW:
+	case MTD_OPS_PLACE_OOB:
+	case MTD_OPS_RAW:
 		memcpy(chip->oob_poi + ops->ooboffs, oob, len);
 		return oob + len;
 
-	case MTD_OOB_AUTO: {
+	case MTD_OPS_AUTO_OOB: {
 		struct nand_oobfree *free = chip->ecc.layout->oobfree;
 		uint32_t boffs = 0, woffs = ops->ooboffs;
 		size_t bytes = 0;
 
 		for (; free->length && len; free++, len -= bytes) {
-			/* Write request not from offset 0 ? */
+			/* Write request not from offset 0? */
 			if (unlikely(woffs)) {
 				if (woffs >= free->length) {
 					woffs -= free->length;
@@ -2146,12 +2164,12 @@ static uint8_t *nand_fill_oob(struct nand_chip *chip, uint8_t *oob, size_t len,
 #define NOTALIGNED(x)	((x & (chip->subpagesize - 1)) != 0)
 
 /**
- * nand_do_write_ops - [Internal] NAND write with ECC
- * @mtd:	MTD device structure
- * @to:		offset to write to
- * @ops:	oob operations description structure
+ * nand_do_write_ops - [INTERN] NAND write with ECC
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @ops: oob operations description structure
  *
- * NAND write with ECC
+ * NAND write with ECC.
  */
 static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
 			     struct mtd_oob_ops *ops)
@@ -2161,7 +2179,7 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
 	uint32_t writelen = ops->len;
 
 	uint32_t oobwritelen = ops->ooblen;
-	uint32_t oobmaxlen = ops->mode == MTD_OOB_AUTO ?
+	uint32_t oobmaxlen = ops->mode == MTD_OPS_AUTO_OOB ?
 				mtd->oobavail : mtd->oobsize;
 
 	uint8_t *oob = ops->oobbuf;
@@ -2172,10 +2190,10 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
 	if (!writelen)
 		return 0;
 
-	/* reject writes, which are not page aligned */
+	/* Reject writes, which are not page aligned */
 	if (NOTALIGNED(to) || NOTALIGNED(ops->len)) {
-		printk(KERN_NOTICE "%s: Attempt to write not "
-				"page aligned data\n", __func__);
+		pr_notice("%s: attempt to write non page aligned data\n",
+			   __func__);
 		return -EINVAL;
 	}
 
@@ -2201,10 +2219,6 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
 	    (chip->pagebuf << chip->page_shift) < (to + ops->len))
 		chip->pagebuf = -1;
 
-	/* If we're not given explicit OOB data, let it be 0xFF */
-	if (likely(!oob))
-		memset(chip->oob_poi, 0xff, mtd->oobsize);
-
 	/* Don't allow multipage oob writes with offset */
 	if (oob && ops->ooboffs && (ops->ooboffs + ops->ooblen > oobmaxlen))
 		return -EINVAL;
@@ -2214,7 +2228,7 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
 		int cached = writelen > bytes && page != blockmask;
 		uint8_t *wbuf = buf;
 
-		/* Partial page write ? */
+		/* Partial page write? */
 		if (unlikely(column || writelen < (mtd->writesize - 1))) {
 			cached = 0;
 			bytes = min_t(int, bytes - column, (int) writelen);
@@ -2226,12 +2240,15 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
 
 		if (unlikely(oob)) {
 			size_t len = min(oobwritelen, oobmaxlen);
-			oob = nand_fill_oob(chip, oob, len, ops);
+			oob = nand_fill_oob(mtd, oob, len, ops);
 			oobwritelen -= len;
+		} else {
+			/* We still need to erase leftover OOB data */
+			memset(chip->oob_poi, 0xff, mtd->oobsize);
 		}
 
 		ret = chip->write_page(mtd, chip, wbuf, page, cached,
-				       (ops->mode == MTD_OOB_RAW));
+				       (ops->mode == MTD_OPS_RAW));
 		if (ret)
 			break;
 
@@ -2260,11 +2277,11 @@ static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
 
 /**
  * panic_nand_write - [MTD Interface] NAND write with ECC
- * @mtd:	MTD device structure
- * @to:		offset to write to
- * @len:	number of bytes to write
- * @retlen:	pointer to variable to store the number of written bytes
- * @buf:	the data to write
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @len: number of bytes to write
+ * @retlen: pointer to variable to store the number of written bytes
+ * @buf: the data to write
  *
  * NAND write with ECC. Used when performing writes in interrupt context, this
  * may for example be called by mtdoops when writing an oops while in panic.
@@ -2273,6 +2290,7 @@ static int panic_nand_write(struct mtd_info *mtd, loff_t to, size_t len,
 			    size_t *retlen, const uint8_t *buf)
 {
 	struct nand_chip *chip = mtd->priv;
+	struct mtd_oob_ops ops;
 	int ret;
 
 	/* Do not allow reads past end of device */
@@ -2281,36 +2299,38 @@ static int panic_nand_write(struct mtd_info *mtd, loff_t to, size_t len,
 	if (!len)
 		return 0;
 
-	/* Wait for the device to get ready.  */
+	/* Wait for the device to get ready */
 	panic_nand_wait(mtd, chip, 400);
 
-	/* Grab the device.  */
+	/* Grab the device */
 	panic_nand_get_device(chip, mtd, FL_WRITING);
 
-	chip->ops.len = len;
-	chip->ops.datbuf = (uint8_t *)buf;
-	chip->ops.oobbuf = NULL;
+	ops.len = len;
+	ops.datbuf = (uint8_t *)buf;
+	ops.oobbuf = NULL;
+	ops.mode = 0;
 
-	ret = nand_do_write_ops(mtd, to, &chip->ops);
+	ret = nand_do_write_ops(mtd, to, &ops);
 
-	*retlen = chip->ops.retlen;
+	*retlen = ops.retlen;
 	return ret;
 }
 
 /**
  * nand_write - [MTD Interface] NAND write with ECC
- * @mtd:	MTD device structure
- * @to:		offset to write to
- * @len:	number of bytes to write
- * @retlen:	pointer to variable to store the number of written bytes
- * @buf:	the data to write
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @len: number of bytes to write
+ * @retlen: pointer to variable to store the number of written bytes
+ * @buf: the data to write
  *
- * NAND write with ECC
+ * NAND write with ECC.
  */
 static int nand_write(struct mtd_info *mtd, loff_t to, size_t len,
 			  size_t *retlen, const uint8_t *buf)
 {
 	struct nand_chip *chip = mtd->priv;
+	struct mtd_oob_ops ops;
 	int ret;
 
 	/* Do not allow reads past end of device */
@@ -2321,13 +2341,14 @@ static int nand_write(struct mtd_info *mtd, loff_t to, size_t len,
 
 	nand_get_device(chip, mtd, FL_WRITING);
 
-	chip->ops.len = len;
-	chip->ops.datbuf = (uint8_t *)buf;
-	chip->ops.oobbuf = NULL;
+	ops.len = len;
+	ops.datbuf = (uint8_t *)buf;
+	ops.oobbuf = NULL;
+	ops.mode = 0;
 
-	ret = nand_do_write_ops(mtd, to, &chip->ops);
+	ret = nand_do_write_ops(mtd, to, &ops);
 
-	*retlen = chip->ops.retlen;
+	*retlen = ops.retlen;
 
 	nand_release_device(mtd);
 
@@ -2336,11 +2357,11 @@ static int nand_write(struct mtd_info *mtd, loff_t to, size_t len,
 
 /**
  * nand_do_write_oob - [MTD Interface] NAND write out-of-band
- * @mtd:	MTD device structure
- * @to:		offset to write to
- * @ops:	oob operation description structure
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @ops: oob operation description structure
  *
- * NAND write out-of-band
+ * NAND write out-of-band.
  */
 static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
 			     struct mtd_oob_ops *ops)
@@ -2348,24 +2369,24 @@ static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
 	int chipnr, page, status, len;
 	struct nand_chip *chip = mtd->priv;
 
-	DEBUG(MTD_DEBUG_LEVEL3, "%s: to = 0x%08x, len = %i\n",
+	pr_debug("%s: to = 0x%08x, len = %i\n",
 			 __func__, (unsigned int)to, (int)ops->ooblen);
 
-	if (ops->mode == MTD_OOB_AUTO)
+	if (ops->mode == MTD_OPS_AUTO_OOB)
 		len = chip->ecc.layout->oobavail;
 	else
 		len = mtd->oobsize;
 
 	/* Do not allow write past end of page */
 	if ((ops->ooboffs + ops->ooblen) > len) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt to write "
-				"past end of page\n", __func__);
+		pr_debug("%s: attempt to write past end of page\n",
+				__func__);
 		return -EINVAL;
 	}
 
 	if (unlikely(ops->ooboffs >= len)) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt to start "
-				"write outside oob\n", __func__);
+		pr_debug("%s: attempt to start write outside oob\n",
+				__func__);
 		return -EINVAL;
 	}
 
@@ -2374,8 +2395,8 @@ static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
 		     ops->ooboffs + ops->ooblen >
 			((mtd->size >> chip->page_shift) -
 			 (to >> chip->page_shift)) * len)) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt write beyond "
-				"end of device\n", __func__);
+		pr_debug("%s: attempt to write beyond end of device\n",
+				__func__);
 		return -EINVAL;
 	}
 
@@ -2401,10 +2422,12 @@ static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
 	if (page == chip->pagebuf)
 		chip->pagebuf = -1;
 
-	memset(chip->oob_poi, 0xff, mtd->oobsize);
-	nand_fill_oob(chip, ops->oobbuf, ops->ooblen, ops);
-	status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask);
-	memset(chip->oob_poi, 0xff, mtd->oobsize);
+	nand_fill_oob(mtd, ops->oobbuf, ops->ooblen, ops);
+
+	if (ops->mode == MTD_OPS_RAW)
+		status = chip->ecc.write_oob_raw(mtd, chip, page & chip->pagemask);
+	else
+		status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask);
 
 	if (status)
 		return status;
@@ -2416,9 +2439,9 @@ static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
 
 /**
  * nand_write_oob - [MTD Interface] NAND write data and/or out-of-band
- * @mtd:	MTD device structure
- * @to:		offset to write to
- * @ops:	oob operation description structure
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @ops: oob operation description structure
  */
 static int nand_write_oob(struct mtd_info *mtd, loff_t to,
 			  struct mtd_oob_ops *ops)
@@ -2430,17 +2453,17 @@ static int nand_write_oob(struct mtd_info *mtd, loff_t to,
 
 	/* Do not allow writes past end of device */
 	if (ops->datbuf && (to + ops->len) > mtd->size) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Attempt write beyond "
-				"end of device\n", __func__);
+		pr_debug("%s: attempt to write beyond end of device\n",
+				__func__);
 		return -EINVAL;
 	}
 
 	nand_get_device(chip, mtd, FL_WRITING);
 
 	switch (ops->mode) {
-	case MTD_OOB_PLACE:
-	case MTD_OOB_AUTO:
-	case MTD_OOB_RAW:
+	case MTD_OPS_PLACE_OOB:
+	case MTD_OPS_AUTO_OOB:
+	case MTD_OPS_RAW:
 		break;
 
 	default:
@@ -2458,11 +2481,11 @@ out:
 }
 
 /**
- * single_erease_cmd - [GENERIC] NAND standard block erase command function
- * @mtd:	MTD device structure
- * @page:	the page address of the block which will be erased
+ * single_erase_cmd - [GENERIC] NAND standard block erase command function
+ * @mtd: MTD device structure
+ * @page: the page address of the block which will be erased
  *
- * Standard erase command for NAND chips
+ * Standard erase command for NAND chips.
  */
 static void single_erase_cmd(struct mtd_info *mtd, int page)
 {
@@ -2473,12 +2496,11 @@ static void single_erase_cmd(struct mtd_info *mtd, int page)
 }
 
 /**
- * multi_erease_cmd - [GENERIC] AND specific block erase command function
- * @mtd:	MTD device structure
- * @page:	the page address of the block which will be erased
+ * multi_erase_cmd - [GENERIC] AND specific block erase command function
+ * @mtd: MTD device structure
+ * @page: the page address of the block which will be erased
  *
- * AND multi block erase command function
- * Erase 4 consecutive blocks
+ * AND multi block erase command function. Erase 4 consecutive blocks.
  */
 static void multi_erase_cmd(struct mtd_info *mtd, int page)
 {
@@ -2493,10 +2515,10 @@ static void multi_erase_cmd(struct mtd_info *mtd, int page)
 
 /**
  * nand_erase - [MTD Interface] erase block(s)
- * @mtd:	MTD device structure
- * @instr:	erase instruction
+ * @mtd: MTD device structure
+ * @instr: erase instruction
  *
- * Erase one ore more blocks
+ * Erase one ore more blocks.
  */
 static int nand_erase(struct mtd_info *mtd, struct erase_info *instr)
 {
@@ -2505,12 +2527,12 @@ static int nand_erase(struct mtd_info *mtd, struct erase_info *instr)
 
 #define BBT_PAGE_MASK	0xffffff3f
 /**
- * nand_erase_nand - [Internal] erase block(s)
- * @mtd:	MTD device structure
- * @instr:	erase instruction
- * @allowbbt:	allow erasing the bbt area
+ * nand_erase_nand - [INTERN] erase block(s)
+ * @mtd: MTD device structure
+ * @instr: erase instruction
+ * @allowbbt: allow erasing the bbt area
  *
- * Erase one ore more blocks
+ * Erase one ore more blocks.
  */
 int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 		    int allowbbt)
@@ -2521,9 +2543,9 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 	unsigned int bbt_masked_page = 0xffffffff;
 	loff_t len;
 
-	DEBUG(MTD_DEBUG_LEVEL3, "%s: start = 0x%012llx, len = %llu\n",
-				__func__, (unsigned long long)instr->addr,
-				(unsigned long long)instr->len);
+	pr_debug("%s: start = 0x%012llx, len = %llu\n",
+			__func__, (unsigned long long)instr->addr,
+			(unsigned long long)instr->len);
 
 	if (check_offs_len(mtd, instr->addr, instr->len))
 		return -EINVAL;
@@ -2545,8 +2567,8 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 
 	/* Check, if it is write protected */
 	if (nand_check_wp(mtd)) {
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: Device is write protected!!!\n",
-					__func__);
+		pr_debug("%s: device is write protected!\n",
+				__func__);
 		instr->state = MTD_ERASE_FAILED;
 		goto erase_exit;
 	}
@@ -2555,7 +2577,7 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 	 * If BBT requires refresh, set the BBT page mask to see if the BBT
 	 * should be rewritten. Otherwise the mask is set to 0xffffffff which
 	 * can not be matched. This is also done when the bbt is actually
-	 * erased to avoid recusrsive updates
+	 * erased to avoid recursive updates.
 	 */
 	if (chip->options & BBT_AUTO_REFRESH && !allowbbt)
 		bbt_masked_page = chip->bbt_td->pages[chipnr] & BBT_PAGE_MASK;
@@ -2566,20 +2588,18 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 	instr->state = MTD_ERASING;
 
 	while (len) {
-		/*
-		 * heck if we have a bad block, we do not erase bad blocks !
-		 */
+		/* Heck if we have a bad block, we do not erase bad blocks! */
 		if (nand_block_checkbad(mtd, ((loff_t) page) <<
 					chip->page_shift, 0, allowbbt)) {
-			printk(KERN_WARNING "%s: attempt to erase a bad block "
-					"at page 0x%08x\n", __func__, page);
+			pr_warn("%s: attempt to erase a bad block at page 0x%08x\n",
+				    __func__, page);
 			instr->state = MTD_ERASE_FAILED;
 			goto erase_exit;
 		}
 
 		/*
 		 * Invalidate the page cache, if we erase the block which
-		 * contains the current cached page
+		 * contains the current cached page.
 		 */
 		if (page <= chip->pagebuf && chip->pagebuf <
 		    (page + pages_per_block))
@@ -2599,8 +2619,8 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 
 		/* See if block erase succeeded */
 		if (status & NAND_STATUS_FAIL) {
-			DEBUG(MTD_DEBUG_LEVEL0, "%s: Failed erase, "
-					"page 0x%08x\n", __func__, page);
+			pr_debug("%s: failed erase, page 0x%08x\n",
+					__func__, page);
 			instr->state = MTD_ERASE_FAILED;
 			instr->fail_addr =
 				((loff_t)page << chip->page_shift);
@@ -2609,7 +2629,7 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 
 		/*
 		 * If BBT requires refresh, set the BBT rewrite flag to the
-		 * page being erased
+		 * page being erased.
 		 */
 		if (bbt_masked_page != 0xffffffff &&
 		    (page & BBT_PAGE_MASK) == bbt_masked_page)
@@ -2628,7 +2648,7 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 
 			/*
 			 * If BBT requires refresh and BBT-PERCHIP, set the BBT
-			 * page mask to see if this BBT should be rewritten
+			 * page mask to see if this BBT should be rewritten.
 			 */
 			if (bbt_masked_page != 0xffffffff &&
 			    (chip->bbt_td->options & NAND_BBT_PERCHIP))
@@ -2651,7 +2671,7 @@ erase_exit:
 
 	/*
 	 * If BBT requires refresh and erase was successful, rewrite any
-	 * selected bad block tables
+	 * selected bad block tables.
 	 */
 	if (bbt_masked_page == 0xffffffff || ret)
 		return ret;
@@ -2659,10 +2679,10 @@ erase_exit:
 	for (chipnr = 0; chipnr < chip->numchips; chipnr++) {
 		if (!rewrite_bbt[chipnr])
 			continue;
-		/* update the BBT for chip */
-		DEBUG(MTD_DEBUG_LEVEL0, "%s: nand_update_bbt "
-			"(%d:0x%0llx 0x%0x)\n", __func__, chipnr,
-			rewrite_bbt[chipnr], chip->bbt_td->pages[chipnr]);
+		/* Update the BBT for chip */
+		pr_debug("%s: nand_update_bbt (%d:0x%0llx 0x%0x)\n",
+				__func__, chipnr, rewrite_bbt[chipnr],
+				chip->bbt_td->pages[chipnr]);
 		nand_update_bbt(mtd, rewrite_bbt[chipnr]);
 	}
 
@@ -2672,15 +2692,15 @@ erase_exit:
 
 /**
  * nand_sync - [MTD Interface] sync
- * @mtd:	MTD device structure
+ * @mtd: MTD device structure
  *
- * Sync is actually a wait for chip ready function
+ * Sync is actually a wait for chip ready function.
  */
 static void nand_sync(struct mtd_info *mtd)
 {
 	struct nand_chip *chip = mtd->priv;
 
-	DEBUG(MTD_DEBUG_LEVEL3, "%s: called\n", __func__);
+	pr_debug("%s: called\n", __func__);
 
 	/* Grab the lock and see if the device is available */
 	nand_get_device(chip, mtd, FL_SYNCING);
@@ -2690,8 +2710,8 @@ static void nand_sync(struct mtd_info *mtd)
 
 /**
  * nand_block_isbad - [MTD Interface] Check if block at offset is bad
- * @mtd:	MTD device structure
- * @offs:	offset relative to mtd start
+ * @mtd: MTD device structure
+ * @offs: offset relative to mtd start
  */
 static int nand_block_isbad(struct mtd_info *mtd, loff_t offs)
 {
@@ -2704,8 +2724,8 @@ static int nand_block_isbad(struct mtd_info *mtd, loff_t offs)
 
 /**
  * nand_block_markbad - [MTD Interface] Mark block at the given offset as bad
- * @mtd:	MTD device structure
- * @ofs:	offset relative to mtd start
+ * @mtd: MTD device structure
+ * @ofs: offset relative to mtd start
  */
 static int nand_block_markbad(struct mtd_info *mtd, loff_t ofs)
 {
@@ -2714,7 +2734,7 @@ static int nand_block_markbad(struct mtd_info *mtd, loff_t ofs)
 
 	ret = nand_block_isbad(mtd, ofs);
 	if (ret) {
-		/* If it was bad already, return success and do nothing. */
+		/* If it was bad already, return success and do nothing */
 		if (ret > 0)
 			return 0;
 		return ret;
@@ -2725,7 +2745,7 @@ static int nand_block_markbad(struct mtd_info *mtd, loff_t ofs)
 
 /**
  * nand_suspend - [MTD Interface] Suspend the NAND flash
- * @mtd:	MTD device structure
+ * @mtd: MTD device structure
  */
 static int nand_suspend(struct mtd_info *mtd)
 {
@@ -2736,7 +2756,7 @@ static int nand_suspend(struct mtd_info *mtd)
 
 /**
  * nand_resume - [MTD Interface] Resume the NAND flash
- * @mtd:	MTD device structure
+ * @mtd: MTD device structure
  */
 static void nand_resume(struct mtd_info *mtd)
 {
@@ -2745,13 +2765,11 @@ static void nand_resume(struct mtd_info *mtd)
 	if (chip->state == FL_PM_SUSPENDED)
 		nand_release_device(mtd);
 	else
-		printk(KERN_ERR "%s called for a chip which is not "
-		       "in suspended state\n", __func__);
+		pr_err("%s called for a chip which is not in suspended state\n",
+			__func__);
 }
 
-/*
- * Set default functions
- */
+/* Set default functions */
 static void nand_set_defaults(struct nand_chip *chip, int busw)
 {
 	/* check for proper chip_delay setup, set 20us if not */
@@ -2793,23 +2811,21 @@ static void nand_set_defaults(struct nand_chip *chip, int busw)
 
 }
 
-/*
- * sanitize ONFI strings so we can safely print them
- */
+/* Sanitize ONFI strings so we can safely print them */
 static void sanitize_string(uint8_t *s, size_t len)
 {
 	ssize_t i;
 
-	/* null terminate */
+	/* Null terminate */
 	s[len - 1] = 0;
 
-	/* remove non printable chars */
+	/* Remove non printable chars */
 	for (i = 0; i < len - 1; i++) {
 		if (s[i] < ' ' || s[i] > 127)
 			s[i] = '?';
 	}
 
-	/* remove trailing spaces */
+	/* Remove trailing spaces */
 	strim(s);
 }
 
@@ -2826,28 +2842,28 @@ static u16 onfi_crc16(u16 crc, u8 const *p, size_t len)
 }
 
 /*
- * Check if the NAND chip is ONFI compliant, returns 1 if it is, 0 otherwise
+ * Check if the NAND chip is ONFI compliant, returns 1 if it is, 0 otherwise.
  */
 static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip,
-					int busw)
+					int *busw)
 {
 	struct nand_onfi_params *p = &chip->onfi_params;
 	int i;
 	int val;
 
-	/* try ONFI for unknow chip or LP */
+	/* Try ONFI for unknown chip or LP */
 	chip->cmdfunc(mtd, NAND_CMD_READID, 0x20, -1);
 	if (chip->read_byte(mtd) != 'O' || chip->read_byte(mtd) != 'N' ||
 		chip->read_byte(mtd) != 'F' || chip->read_byte(mtd) != 'I')
 		return 0;
 
-	printk(KERN_INFO "ONFI flash detected\n");
+	pr_info("ONFI flash detected\n");
 	chip->cmdfunc(mtd, NAND_CMD_PARAM, 0, -1);
 	for (i = 0; i < 3; i++) {
 		chip->read_buf(mtd, (uint8_t *)p, sizeof(*p));
 		if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 254) ==
 				le16_to_cpu(p->crc)) {
-			printk(KERN_INFO "ONFI param page %d valid\n", i);
+			pr_info("ONFI param page %d valid\n", i);
 			break;
 		}
 	}
@@ -2855,7 +2871,7 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip,
 	if (i == 3)
 		return 0;
 
-	/* check version */
+	/* Check version */
 	val = le16_to_cpu(p->revision);
 	if (val & (1 << 5))
 		chip->onfi_version = 23;
@@ -2871,8 +2887,7 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip,
 		chip->onfi_version = 0;
 
 	if (!chip->onfi_version) {
-		printk(KERN_INFO "%s: unsupported ONFI version: %d\n",
-								__func__, val);
+		pr_info("%s: unsupported ONFI version: %d\n", __func__, val);
 		return 0;
 	}
 
@@ -2884,9 +2899,9 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip,
 	mtd->erasesize = le32_to_cpu(p->pages_per_block) * mtd->writesize;
 	mtd->oobsize = le16_to_cpu(p->spare_bytes_per_page);
 	chip->chipsize = (uint64_t)le32_to_cpu(p->blocks_per_lun) * mtd->erasesize;
-	busw = 0;
+	*busw = 0;
 	if (le16_to_cpu(p->features) & 1)
-		busw = NAND_BUSWIDTH_16;
+		*busw = NAND_BUSWIDTH_16;
 
 	chip->options &= ~NAND_CHIPOPTIONS_MSK;
 	chip->options |= (NAND_NO_READRDY |
@@ -2896,7 +2911,7 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip,
 }
 
 /*
- * Get the flash and manufacturer id and lookup if the type is supported
+ * Get the flash and manufacturer id and lookup if the type is supported.
  */
 static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
 						  struct nand_chip *chip,
@@ -2913,7 +2928,7 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
 
 	/*
 	 * Reset the chip, required by some chips (e.g. Micron MT29FxGxxxxx)
-	 * after power-up
+	 * after power-up.
 	 */
 	chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
 
@@ -2924,7 +2939,8 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
 	*maf_id = chip->read_byte(mtd);
 	*dev_id = chip->read_byte(mtd);
 
-	/* Try again to make sure, as some systems the bus-hold or other
+	/*
+	 * Try again to make sure, as some systems the bus-hold or other
 	 * interface concerns can cause random data which looks like a
 	 * possibly credible NAND flash to appear. If the two results do
 	 * not match, ignore the device completely.
@@ -2936,9 +2952,9 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
 		id_data[i] = chip->read_byte(mtd);
 
 	if (id_data[0] != *maf_id || id_data[1] != *dev_id) {
-		printk(KERN_INFO "%s: second ID read did not match "
-		       "%02x,%02x against %02x,%02x\n", __func__,
-		       *maf_id, *dev_id, id_data[0], id_data[1]);
+		pr_info("%s: second ID read did not match "
+			"%02x,%02x against %02x,%02x\n", __func__,
+			*maf_id, *dev_id, id_data[0], id_data[1]);
 		return ERR_PTR(-ENODEV);
 	}
 
@@ -2952,7 +2968,7 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
 	chip->onfi_version = 0;
 	if (!type->name || !type->pagesize) {
 		/* Check is chip is ONFI compliant */
-		ret = nand_flash_detect_onfi(mtd, chip, busw);
+		ret = nand_flash_detect_onfi(mtd, chip, &busw);
 		if (ret)
 			goto ident_done;
 	}
@@ -2973,7 +2989,7 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
 	chip->chipsize = (uint64_t)type->chipsize << 20;
 
 	if (!type->pagesize && chip->init_size) {
-		/* set the pagesize, oobsize, erasesize by the driver*/
+		/* Set the pagesize, oobsize, erasesize by the driver */
 		busw = chip->init_size(mtd, chip, id_data);
 	} else if (!type->pagesize) {
 		int extid;
@@ -3033,7 +3049,7 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
 		}
 	} else {
 		/*
-		 * Old devices have chip data hardcoded in the device id table
+		 * Old devices have chip data hardcoded in the device id table.
 		 */
 		mtd->erasesize = type->erasesize;
 		mtd->writesize = type->pagesize;
@@ -3043,7 +3059,7 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
 		/*
 		 * Check for Spansion/AMD ID + repeating 5th, 6th byte since
 		 * some Spansion chips have erasesize that conflicts with size
-		 * listed in nand_ids table
+		 * listed in nand_ids table.
 		 * Data sheet (5 byte ID): Spansion S30ML-P ORNAND (p.39)
 		 */
 		if (*maf_id == NAND_MFR_AMD && id_data[4] != 0x00 &&
@@ -3057,15 +3073,16 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
 	chip->options &= ~NAND_CHIPOPTIONS_MSK;
 	chip->options |= type->options & NAND_CHIPOPTIONS_MSK;
 
-	/* Check if chip is a not a samsung device. Do not clear the
-	 * options for chips which are not having an extended id.
+	/*
+	 * Check if chip is not a Samsung device. Do not clear the
+	 * options for chips which do not have an extended id.
 	 */
 	if (*maf_id != NAND_MFR_SAMSUNG && !type->pagesize)
 		chip->options &= ~NAND_SAMSUNG_LP_OPTIONS;
 ident_done:
 
 	/*
-	 * Set chip as a default. Board drivers can override it, if necessary
+	 * Set chip as a default. Board drivers can override it, if necessary.
 	 */
 	chip->options |= NAND_NO_AUTOINCR;
 
@@ -3077,21 +3094,21 @@ ident_done:
 
 	/*
 	 * Check, if buswidth is correct. Hardware drivers should set
-	 * chip correct !
+	 * chip correct!
 	 */
 	if (busw != (chip->options & NAND_BUSWIDTH_16)) {
-		printk(KERN_INFO "NAND device: Manufacturer ID:"
-		       " 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id,
-		       *dev_id, nand_manuf_ids[maf_idx].name, mtd->name);
-		printk(KERN_WARNING "NAND bus width %d instead %d bit\n",
-		       (chip->options & NAND_BUSWIDTH_16) ? 16 : 8,
-		       busw ? 16 : 8);
+		pr_info("NAND device: Manufacturer ID:"
+			" 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id,
+			*dev_id, nand_manuf_ids[maf_idx].name, mtd->name);
+		pr_warn("NAND bus width %d instead %d bit\n",
+			   (chip->options & NAND_BUSWIDTH_16) ? 16 : 8,
+			   busw ? 16 : 8);
 		return ERR_PTR(-EINVAL);
 	}
 
 	/* Calculate the address shift from the page size */
 	chip->page_shift = ffs(mtd->writesize) - 1;
-	/* Convert chipsize to number of pages per chip -1. */
+	/* Convert chipsize to number of pages per chip -1 */
 	chip->pagemask = (chip->chipsize >> chip->page_shift) - 1;
 
 	chip->bbt_erase_shift = chip->phys_erase_shift =
@@ -3121,7 +3138,7 @@ ident_done:
 	if ((chip->cellinfo & NAND_CI_CELLTYPE_MSK) &&
 			(*maf_id == NAND_MFR_SAMSUNG ||
 			 *maf_id == NAND_MFR_HYNIX))
-		chip->options |= NAND_BBT_SCANLASTPAGE;
+		chip->bbt_options |= NAND_BBT_SCANLASTPAGE;
 	else if ((!(chip->cellinfo & NAND_CI_CELLTYPE_MSK) &&
 				(*maf_id == NAND_MFR_SAMSUNG ||
 				 *maf_id == NAND_MFR_HYNIX ||
@@ -3129,17 +3146,7 @@ ident_done:
 				 *maf_id == NAND_MFR_AMD)) ||
 			(mtd->writesize == 2048 &&
 			 *maf_id == NAND_MFR_MICRON))
-		chip->options |= NAND_BBT_SCAN2NDPAGE;
-
-	/*
-	 * Numonyx/ST 2K pages, x8 bus use BOTH byte 1 and 6
-	 */
-	if (!(busw & NAND_BUSWIDTH_16) &&
-			*maf_id == NAND_MFR_STMICRO &&
-			mtd->writesize == 2048) {
-		chip->options |= NAND_BBT_SCANBYTE1AND6;
-		chip->badblockpos = 0;
-	}
+		chip->bbt_options |= NAND_BBT_SCAN2NDPAGE;
 
 	/* Check for AND chips with 4 page planes */
 	if (chip->options & NAND_4PAGE_ARRAY)
@@ -3147,12 +3154,11 @@ ident_done:
 	else
 		chip->erase_cmd = single_erase_cmd;
 
-	/* Do not replace user supplied command function ! */
+	/* Do not replace user supplied command function! */
 	if (mtd->writesize > 512 && chip->cmdfunc == nand_command)
 		chip->cmdfunc = nand_command_lp;
 
-	/* TODO onfi flash name */
-	printk(KERN_INFO "NAND device: Manufacturer ID:"
+	pr_info("NAND device: Manufacturer ID:"
 		" 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id, *dev_id,
 		nand_manuf_ids[maf_idx].name,
 		chip->onfi_version ? chip->onfi_params.model : type->name);
@@ -3162,12 +3168,12 @@ ident_done:
 
 /**
  * nand_scan_ident - [NAND Interface] Scan for the NAND device
- * @mtd:	     MTD device structure
- * @maxchips:	     Number of chips to scan for
- * @table:	     Alternative NAND ID table
+ * @mtd: MTD device structure
+ * @maxchips: number of chips to scan for
+ * @table: alternative NAND ID table
  *
- * This is the first phase of the normal nand_scan() function. It
- * reads the flash ID and sets up MTD fields accordingly.
+ * This is the first phase of the normal nand_scan() function. It reads the
+ * flash ID and sets up MTD fields accordingly.
  *
  * The mtd->owner field must be set to the module of the caller.
  */
@@ -3189,7 +3195,7 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips,
 
 	if (IS_ERR(type)) {
 		if (!(chip->options & NAND_SCAN_SILENT_NODEV))
-			printk(KERN_WARNING "No NAND device found.\n");
+			pr_warn("No NAND device found\n");
 		chip->select_chip(mtd, -1);
 		return PTR_ERR(type);
 	}
@@ -3207,7 +3213,7 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips,
 			break;
 	}
 	if (i > 1)
-		printk(KERN_INFO "%d NAND chips detected\n", i);
+		pr_info("%d NAND chips detected\n", i);
 
 	/* Store the number of chips and calc total size for mtd */
 	chip->numchips = i;
@@ -3220,11 +3226,11 @@ EXPORT_SYMBOL(nand_scan_ident);
 
 /**
  * nand_scan_tail - [NAND Interface] Scan for the NAND device
- * @mtd:	    MTD device structure
+ * @mtd: MTD device structure
  *
- * This is the second phase of the normal nand_scan() function. It
- * fills out all the uninitialized function pointers with the defaults
- * and scans for a bad block table if appropriate.
+ * This is the second phase of the normal nand_scan() function. It fills out
+ * all the uninitialized function pointers with the defaults and scans for a
+ * bad block table if appropriate.
  */
 int nand_scan_tail(struct mtd_info *mtd)
 {
@@ -3240,7 +3246,7 @@ int nand_scan_tail(struct mtd_info *mtd)
 	chip->oob_poi = chip->buffers->databuf + mtd->writesize;
 
 	/*
-	 * If no default placement scheme is given, select an appropriate one
+	 * If no default placement scheme is given, select an appropriate one.
 	 */
 	if (!chip->ecc.layout && (chip->ecc.mode != NAND_ECC_SOFT_BCH)) {
 		switch (mtd->oobsize) {
@@ -3257,8 +3263,8 @@ int nand_scan_tail(struct mtd_info *mtd)
 			chip->ecc.layout = &nand_oob_128;
 			break;
 		default:
-			printk(KERN_WARNING "No oob scheme defined for "
-			       "oobsize %d\n", mtd->oobsize);
+			pr_warn("No oob scheme defined for oobsize %d\n",
+				   mtd->oobsize);
 			BUG();
 		}
 	}
@@ -3267,7 +3273,7 @@ int nand_scan_tail(struct mtd_info *mtd)
 		chip->write_page = nand_write_page;
 
 	/*
-	 * check ECC mode, default to software if 3byte/512byte hardware ECC is
+	 * Check ECC mode, default to software if 3byte/512byte hardware ECC is
 	 * selected and we have 256 byte pagesize fallback to software ECC
 	 */
 
@@ -3276,15 +3282,15 @@ int nand_scan_tail(struct mtd_info *mtd)
 		/* Similar to NAND_ECC_HW, but a separate read_page handle */
 		if (!chip->ecc.calculate || !chip->ecc.correct ||
 		     !chip->ecc.hwctl) {
-			printk(KERN_WARNING "No ECC functions supplied; "
-			       "Hardware ECC not possible\n");
+			pr_warn("No ECC functions supplied; "
+				   "hardware ECC not possible\n");
 			BUG();
 		}
 		if (!chip->ecc.read_page)
 			chip->ecc.read_page = nand_read_page_hwecc_oob_first;
 
 	case NAND_ECC_HW:
-		/* Use standard hwecc read page function ? */
+		/* Use standard hwecc read page function? */
 		if (!chip->ecc.read_page)
 			chip->ecc.read_page = nand_read_page_hwecc;
 		if (!chip->ecc.write_page)
@@ -3305,11 +3311,11 @@ int nand_scan_tail(struct mtd_info *mtd)
 		     chip->ecc.read_page == nand_read_page_hwecc ||
 		     !chip->ecc.write_page ||
 		     chip->ecc.write_page == nand_write_page_hwecc)) {
-			printk(KERN_WARNING "No ECC functions supplied; "
-			       "Hardware ECC not possible\n");
+			pr_warn("No ECC functions supplied; "
+				   "hardware ECC not possible\n");
 			BUG();
 		}
-		/* Use standard syndrome read/write page function ? */
+		/* Use standard syndrome read/write page function? */
 		if (!chip->ecc.read_page)
 			chip->ecc.read_page = nand_read_page_syndrome;
 		if (!chip->ecc.write_page)
@@ -3325,9 +3331,9 @@ int nand_scan_tail(struct mtd_info *mtd)
 
 		if (mtd->writesize >= chip->ecc.size)
 			break;
-		printk(KERN_WARNING "%d byte HW ECC not possible on "
-		       "%d byte page size, fallback to SW ECC\n",
-		       chip->ecc.size, mtd->writesize);
+		pr_warn("%d byte HW ECC not possible on "
+			   "%d byte page size, fallback to SW ECC\n",
+			   chip->ecc.size, mtd->writesize);
 		chip->ecc.mode = NAND_ECC_SOFT;
 
 	case NAND_ECC_SOFT:
@@ -3347,7 +3353,7 @@ int nand_scan_tail(struct mtd_info *mtd)
 
 	case NAND_ECC_SOFT_BCH:
 		if (!mtd_nand_has_bch()) {
-			printk(KERN_WARNING "CONFIG_MTD_ECC_BCH not enabled\n");
+			pr_warn("CONFIG_MTD_ECC_BCH not enabled\n");
 			BUG();
 		}
 		chip->ecc.calculate = nand_bch_calculate_ecc;
@@ -3362,8 +3368,8 @@ int nand_scan_tail(struct mtd_info *mtd)
 		/*
 		 * Board driver should supply ecc.size and ecc.bytes values to
 		 * select how many bits are correctable; see nand_bch_init()
-		 * for details.
-		 * Otherwise, default to 4 bits for large page devices
+		 * for details. Otherwise, default to 4 bits for large page
+		 * devices.
 		 */
 		if (!chip->ecc.size && (mtd->oobsize >= 64)) {
 			chip->ecc.size = 512;
@@ -3374,14 +3380,14 @@ int nand_scan_tail(struct mtd_info *mtd)
 					       chip->ecc.bytes,
 					       &chip->ecc.layout);
 		if (!chip->ecc.priv) {
-			printk(KERN_WARNING "BCH ECC initialization failed!\n");
+			pr_warn("BCH ECC initialization failed!\n");
 			BUG();
 		}
 		break;
 
 	case NAND_ECC_NONE:
-		printk(KERN_WARNING "NAND_ECC_NONE selected by board driver. "
-		       "This is not recommended !!\n");
+		pr_warn("NAND_ECC_NONE selected by board driver. "
+			   "This is not recommended!\n");
 		chip->ecc.read_page = nand_read_page_raw;
 		chip->ecc.write_page = nand_write_page_raw;
 		chip->ecc.read_oob = nand_read_oob_std;
@@ -3393,14 +3399,19 @@ int nand_scan_tail(struct mtd_info *mtd)
 		break;
 
 	default:
-		printk(KERN_WARNING "Invalid NAND_ECC_MODE %d\n",
-		       chip->ecc.mode);
+		pr_warn("Invalid NAND_ECC_MODE %d\n", chip->ecc.mode);
 		BUG();
 	}
 
+	/* For many systems, the standard OOB write also works for raw */
+	if (!chip->ecc.read_oob_raw)
+		chip->ecc.read_oob_raw = chip->ecc.read_oob;
+	if (!chip->ecc.write_oob_raw)
+		chip->ecc.write_oob_raw = chip->ecc.write_oob;
+
 	/*
 	 * The number of bytes available for a client to place data into
-	 * the out of band area
+	 * the out of band area.
 	 */
 	chip->ecc.layout->oobavail = 0;
 	for (i = 0; chip->ecc.layout->oobfree[i].length
@@ -3411,19 +3422,16 @@ int nand_scan_tail(struct mtd_info *mtd)
 
 	/*
 	 * Set the number of read / write steps for one page depending on ECC
-	 * mode
+	 * mode.
 	 */
 	chip->ecc.steps = mtd->writesize / chip->ecc.size;
 	if (chip->ecc.steps * chip->ecc.size != mtd->writesize) {
-		printk(KERN_WARNING "Invalid ecc parameters\n");
+		pr_warn("Invalid ECC parameters\n");
 		BUG();
 	}
 	chip->ecc.total = chip->ecc.steps * chip->ecc.bytes;
 
-	/*
-	 * Allow subpage writes up to ecc.steps. Not possible for MLC
-	 * FLASH.
-	 */
+	/* Allow subpage writes up to ecc.steps. Not possible for MLC flash */
 	if (!(chip->options & NAND_NO_SUBPAGE_WRITE) &&
 	    !(chip->cellinfo & NAND_CI_CELLTYPE_MSK)) {
 		switch (chip->ecc.steps) {
@@ -3481,9 +3489,11 @@ int nand_scan_tail(struct mtd_info *mtd)
 }
 EXPORT_SYMBOL(nand_scan_tail);
 
-/* is_module_text_address() isn't exported, and it's mostly a pointless
+/*
+ * is_module_text_address() isn't exported, and it's mostly a pointless
  * test if this is a module _anyway_ -- they'd have to try _really_ hard
- * to call us from in-kernel code if the core NAND support is modular. */
+ * to call us from in-kernel code if the core NAND support is modular.
+ */
 #ifdef MODULE
 #define caller_is_module() (1)
 #else
@@ -3493,15 +3503,13 @@ EXPORT_SYMBOL(nand_scan_tail);
 
 /**
  * nand_scan - [NAND Interface] Scan for the NAND device
- * @mtd:	MTD device structure
- * @maxchips:	Number of chips to scan for
- *
- * This fills out all the uninitialized function pointers
- * with the defaults.
- * The flash ID is read and the mtd/chip structures are
- * filled with the appropriate values.
- * The mtd->owner field must be set to the module of the caller
+ * @mtd: MTD device structure
+ * @maxchips: number of chips to scan for
  *
+ * This fills out all the uninitialized function pointers with the defaults.
+ * The flash ID is read and the mtd/chip structures are filled with the
+ * appropriate values. The mtd->owner field must be set to the module of the
+ * caller.
  */
 int nand_scan(struct mtd_info *mtd, int maxchips)
 {
@@ -3509,8 +3517,7 @@ int nand_scan(struct mtd_info *mtd, int maxchips)
 
 	/* Many callers got this wrong, so check for it for a while... */
 	if (!mtd->owner && caller_is_module()) {
-		printk(KERN_CRIT "%s called with NULL mtd->owner!\n",
-				__func__);
+		pr_crit("%s called with NULL mtd->owner!\n", __func__);
 		BUG();
 	}
 
@@ -3523,8 +3530,8 @@ EXPORT_SYMBOL(nand_scan);
 
 /**
  * nand_release - [NAND Interface] Free resources held by the NAND device
- * @mtd:	MTD device structure
-*/
+ * @mtd: MTD device structure
+ */
 void nand_release(struct mtd_info *mtd)
 {
 	struct nand_chip *chip = mtd->priv;
diff --git a/drivers/mtd/nand/nand_bbt.c b/drivers/mtd/nand/nand_bbt.c
index 4165857752ca..69148ae3bf58 100644
--- a/drivers/mtd/nand/nand_bbt.c
+++ b/drivers/mtd/nand/nand_bbt.c
@@ -14,7 +14,7 @@
  *
  * When nand_scan_bbt is called, then it tries to find the bad block table
  * depending on the options in the BBT descriptor(s). If no flash based BBT
- * (NAND_USE_FLASH_BBT) is specified then the device is scanned for factory
+ * (NAND_BBT_USE_FLASH) is specified then the device is scanned for factory
  * marked good / bad blocks. This information is used to create a memory BBT.
  * Once a new bad block is discovered then the "factory" information is updated
  * on the device.
@@ -36,9 +36,9 @@
  * The table is marked in the OOB area with an ident pattern and a version
  * number which indicates which of both tables is more up to date. If the NAND
  * controller needs the complete OOB area for the ECC information then the
- * option NAND_USE_FLASH_BBT_NO_OOB should be used: it moves the ident pattern
- * and the version byte into the data area and the OOB area will remain
- * untouched.
+ * option NAND_BBT_NO_OOB should be used (along with NAND_BBT_USE_FLASH, of
+ * course): it moves the ident pattern and the version byte into the data area
+ * and the OOB area will remain untouched.
  *
  * The table uses 2 bits per block
  * 11b:		block is good
@@ -81,17 +81,15 @@ static int check_pattern_no_oob(uint8_t *buf, struct nand_bbt_descr *td)
 
 /**
  * check_pattern - [GENERIC] check if a pattern is in the buffer
- * @buf:	the buffer to search
- * @len:	the length of buffer to search
- * @paglen:	the pagelength
- * @td:		search pattern descriptor
+ * @buf: the buffer to search
+ * @len: the length of buffer to search
+ * @paglen: the pagelength
+ * @td: search pattern descriptor
  *
- * Check for a pattern at the given place. Used to search bad block
- * tables and good / bad block identifiers.
- * If the SCAN_EMPTY option is set then check, if all bytes except the
- * pattern area contain 0xff
- *
-*/
+ * Check for a pattern at the given place. Used to search bad block tables and
+ * good / bad block identifiers. If the SCAN_EMPTY option is set then check, if
+ * all bytes except the pattern area contain 0xff.
+ */
 static int check_pattern(uint8_t *buf, int len, int paglen, struct nand_bbt_descr *td)
 {
 	int i, end = 0;
@@ -110,32 +108,8 @@ static int check_pattern(uint8_t *buf, int len, int paglen, struct nand_bbt_desc
 	p += end;
 
 	/* Compare the pattern */
-	for (i = 0; i < td->len; i++) {
-		if (p[i] != td->pattern[i])
-			return -1;
-	}
-
-	/* Check both positions 1 and 6 for pattern? */
-	if (td->options & NAND_BBT_SCANBYTE1AND6) {
-		if (td->options & NAND_BBT_SCANEMPTY) {
-			p += td->len;
-			end += NAND_SMALL_BADBLOCK_POS - td->offs;
-			/* Check region between positions 1 and 6 */
-			for (i = 0; i < NAND_SMALL_BADBLOCK_POS - td->offs - td->len;
-					i++) {
-				if (*p++ != 0xff)
-					return -1;
-			}
-		}
-		else {
-			p += NAND_SMALL_BADBLOCK_POS - td->offs;
-		}
-		/* Compare the pattern */
-		for (i = 0; i < td->len; i++) {
-			if (p[i] != td->pattern[i])
-				return -1;
-		}
-	}
+	if (memcmp(p, td->pattern, td->len))
+		return -1;
 
 	if (td->options & NAND_BBT_SCANEMPTY) {
 		p += td->len;
@@ -150,14 +124,13 @@ static int check_pattern(uint8_t *buf, int len, int paglen, struct nand_bbt_desc
 
 /**
  * check_short_pattern - [GENERIC] check if a pattern is in the buffer
- * @buf:	the buffer to search
- * @td:		search pattern descriptor
- *
- * Check for a pattern at the given place. Used to search bad block
- * tables and good / bad block identifiers. Same as check_pattern, but
- * no optional empty check
+ * @buf: the buffer to search
+ * @td:	search pattern descriptor
  *
-*/
+ * Check for a pattern at the given place. Used to search bad block tables and
+ * good / bad block identifiers. Same as check_pattern, but no optional empty
+ * check.
+ */
 static int check_short_pattern(uint8_t *buf, struct nand_bbt_descr *td)
 {
 	int i;
@@ -168,21 +141,14 @@ static int check_short_pattern(uint8_t *buf, struct nand_bbt_descr *td)
 		if (p[td->offs + i] != td->pattern[i])
 			return -1;
 	}
-	/* Need to check location 1 AND 6? */
-	if (td->options & NAND_BBT_SCANBYTE1AND6) {
-		for (i = 0; i < td->len; i++) {
-			if (p[NAND_SMALL_BADBLOCK_POS + i] != td->pattern[i])
-				return -1;
-		}
-	}
 	return 0;
 }
 
 /**
  * add_marker_len - compute the length of the marker in data area
- * @td:		BBT descriptor used for computation
+ * @td: BBT descriptor used for computation
  *
- * The length will be 0 if the markeris located in OOB area.
+ * The length will be 0 if the marker is located in OOB area.
  */
 static u32 add_marker_len(struct nand_bbt_descr *td)
 {
@@ -199,34 +165,33 @@ static u32 add_marker_len(struct nand_bbt_descr *td)
 
 /**
  * read_bbt - [GENERIC] Read the bad block table starting from page
- * @mtd:	MTD device structure
- * @buf:	temporary buffer
- * @page:	the starting page
- * @num:	the number of bbt descriptors to read
- * @td:		the bbt describtion table
- * @offs:	offset in the memory table
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @page: the starting page
+ * @num: the number of bbt descriptors to read
+ * @td: the bbt describtion table
+ * @offs: offset in the memory table
  *
  * Read the bad block table starting from page.
- *
  */
 static int read_bbt(struct mtd_info *mtd, uint8_t *buf, int page, int num,
 		struct nand_bbt_descr *td, int offs)
 {
-	int res, i, j, act = 0;
+	int res, ret = 0, i, j, act = 0;
 	struct nand_chip *this = mtd->priv;
 	size_t retlen, len, totlen;
 	loff_t from;
 	int bits = td->options & NAND_BBT_NRBITS_MSK;
-	uint8_t msk = (uint8_t) ((1 << bits) - 1);
+	uint8_t msk = (uint8_t)((1 << bits) - 1);
 	u32 marker_len;
 	int reserved_block_code = td->reserved_block_code;
 
 	totlen = (num * bits) >> 3;
 	marker_len = add_marker_len(td);
-	from = ((loff_t) page) << this->page_shift;
+	from = ((loff_t)page) << this->page_shift;
 
 	while (totlen) {
-		len = min(totlen, (size_t) (1 << this->bbt_erase_shift));
+		len = min(totlen, (size_t)(1 << this->bbt_erase_shift));
 		if (marker_len) {
 			/*
 			 * In case the BBT marker is not in the OOB area it
@@ -238,11 +203,18 @@ static int read_bbt(struct mtd_info *mtd, uint8_t *buf, int page, int num,
 		}
 		res = mtd->read(mtd, from, len, &retlen, buf);
 		if (res < 0) {
-			if (retlen != len) {
-				printk(KERN_INFO "nand_bbt: Error reading bad block table\n");
+			if (mtd_is_eccerr(res)) {
+				pr_info("nand_bbt: ECC error in BBT at "
+					"0x%012llx\n", from & ~mtd->writesize);
+				return res;
+			} else if (mtd_is_bitflip(res)) {
+				pr_info("nand_bbt: corrected error in BBT at "
+					"0x%012llx\n", from & ~mtd->writesize);
+				ret = res;
+			} else {
+				pr_info("nand_bbt: error reading BBT\n");
 				return res;
 			}
-			printk(KERN_WARNING "nand_bbt: ECC error while reading bad block table\n");
 		}
 
 		/* Analyse data */
@@ -253,17 +225,19 @@ static int read_bbt(struct mtd_info *mtd, uint8_t *buf, int page, int num,
 				if (tmp == msk)
 					continue;
 				if (reserved_block_code && (tmp == reserved_block_code)) {
-					printk(KERN_DEBUG "nand_read_bbt: Reserved block at 0x%012llx\n",
-					       (loff_t)((offs << 2) + (act >> 1)) << this->bbt_erase_shift);
+					pr_info("nand_read_bbt: reserved block at 0x%012llx\n",
+						 (loff_t)((offs << 2) + (act >> 1)) << this->bbt_erase_shift);
 					this->bbt[offs + (act >> 3)] |= 0x2 << (act & 0x06);
 					mtd->ecc_stats.bbtblocks++;
 					continue;
 				}
-				/* Leave it for now, if its matured we can move this
-				 * message to MTD_DEBUG_LEVEL0 */
-				printk(KERN_DEBUG "nand_read_bbt: Bad block at 0x%012llx\n",
-				       (loff_t)((offs << 2) + (act >> 1)) << this->bbt_erase_shift);
-				/* Factory marked bad or worn out ? */
+				/*
+				 * Leave it for now, if it's matured we can
+				 * move this message to pr_debug.
+				 */
+				pr_info("nand_read_bbt: bad block at 0x%012llx\n",
+					 (loff_t)((offs << 2) + (act >> 1)) << this->bbt_erase_shift);
+				/* Factory marked bad or worn out? */
 				if (tmp == 0)
 					this->bbt[offs + (act >> 3)] |= 0x3 << (act & 0x06);
 				else
@@ -274,20 +248,20 @@ static int read_bbt(struct mtd_info *mtd, uint8_t *buf, int page, int num,
 		totlen -= len;
 		from += len;
 	}
-	return 0;
+	return ret;
 }
 
 /**
  * read_abs_bbt - [GENERIC] Read the bad block table starting at a given page
- * @mtd:	MTD device structure
- * @buf:	temporary buffer
- * @td:		descriptor for the bad block table
- * @chip:	read the table for a specific chip, -1 read all chips.
- *		Applies only if NAND_BBT_PERCHIP option is set
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @td: descriptor for the bad block table
+ * @chip: read the table for a specific chip, -1 read all chips; applies only if
+ *        NAND_BBT_PERCHIP option is set
  *
- * Read the bad block table for all chips starting at a given page
- * We assume that the bbt bits are in consecutive order.
-*/
+ * Read the bad block table for all chips starting at a given page. We assume
+ * that the bbt bits are in consecutive order.
+ */
 static int read_abs_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *td, int chip)
 {
 	struct nand_chip *this = mtd->priv;
@@ -313,9 +287,7 @@ static int read_abs_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_desc
 	return 0;
 }
 
-/*
- * BBT marker is in the first page, no OOB.
- */
+/* BBT marker is in the first page, no OOB */
 static int scan_read_raw_data(struct mtd_info *mtd, uint8_t *buf, loff_t offs,
 			 struct nand_bbt_descr *td)
 {
@@ -329,35 +301,26 @@ static int scan_read_raw_data(struct mtd_info *mtd, uint8_t *buf, loff_t offs,
 	return mtd->read(mtd, offs, len, &retlen, buf);
 }
 
-/*
- * Scan read raw data from flash
- */
+/* Scan read raw data from flash */
 static int scan_read_raw_oob(struct mtd_info *mtd, uint8_t *buf, loff_t offs,
 			 size_t len)
 {
 	struct mtd_oob_ops ops;
 	int res;
 
-	ops.mode = MTD_OOB_RAW;
+	ops.mode = MTD_OPS_RAW;
 	ops.ooboffs = 0;
 	ops.ooblen = mtd->oobsize;
 
-
 	while (len > 0) {
-		if (len <= mtd->writesize) {
-			ops.oobbuf = buf + len;
-			ops.datbuf = buf;
-			ops.len = len;
-			return mtd->read_oob(mtd, offs, &ops);
-		} else {
-			ops.oobbuf = buf + mtd->writesize;
-			ops.datbuf = buf;
-			ops.len = mtd->writesize;
-			res = mtd->read_oob(mtd, offs, &ops);
+		ops.datbuf = buf;
+		ops.len = min(len, (size_t)mtd->writesize);
+		ops.oobbuf = buf + ops.len;
 
-			if (res)
-				return res;
-		}
+		res = mtd->read_oob(mtd, offs, &ops);
+
+		if (res)
+			return res;
 
 		buf += mtd->oobsize + mtd->writesize;
 		len -= mtd->writesize;
@@ -374,15 +337,13 @@ static int scan_read_raw(struct mtd_info *mtd, uint8_t *buf, loff_t offs,
 		return scan_read_raw_oob(mtd, buf, offs, len);
 }
 
-/*
- * Scan write data with oob to flash
- */
+/* Scan write data with oob to flash */
 static int scan_write_bbt(struct mtd_info *mtd, loff_t offs, size_t len,
 			  uint8_t *buf, uint8_t *oob)
 {
 	struct mtd_oob_ops ops;
 
-	ops.mode = MTD_OOB_PLACE;
+	ops.mode = MTD_OPS_PLACE_OOB;
 	ops.ooboffs = 0;
 	ops.ooblen = mtd->oobsize;
 	ops.datbuf = buf;
@@ -403,15 +364,14 @@ static u32 bbt_get_ver_offs(struct mtd_info *mtd, struct nand_bbt_descr *td)
 
 /**
  * read_abs_bbts - [GENERIC] Read the bad block table(s) for all chips starting at a given page
- * @mtd:	MTD device structure
- * @buf:	temporary buffer
- * @td:		descriptor for the bad block table
- * @md:		descriptor for the bad block table mirror
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @td: descriptor for the bad block table
+ * @md:	descriptor for the bad block table mirror
  *
- * Read the bad block table(s) for all chips starting at a given page
- * We assume that the bbt bits are in consecutive order.
- *
-*/
+ * Read the bad block table(s) for all chips starting at a given page. We
+ * assume that the bbt bits are in consecutive order.
+ */
 static int read_abs_bbts(struct mtd_info *mtd, uint8_t *buf,
 			 struct nand_bbt_descr *td, struct nand_bbt_descr *md)
 {
@@ -422,8 +382,8 @@ static int read_abs_bbts(struct mtd_info *mtd, uint8_t *buf,
 		scan_read_raw(mtd, buf, (loff_t)td->pages[0] << this->page_shift,
 			      mtd->writesize, td);
 		td->version[0] = buf[bbt_get_ver_offs(mtd, td)];
-		printk(KERN_DEBUG "Bad block table at page %d, version 0x%02X\n",
-		       td->pages[0], td->version[0]);
+		pr_info("Bad block table at page %d, version 0x%02X\n",
+			 td->pages[0], td->version[0]);
 	}
 
 	/* Read the mirror version, if available */
@@ -431,15 +391,13 @@ static int read_abs_bbts(struct mtd_info *mtd, uint8_t *buf,
 		scan_read_raw(mtd, buf, (loff_t)md->pages[0] << this->page_shift,
 			      mtd->writesize, td);
 		md->version[0] = buf[bbt_get_ver_offs(mtd, md)];
-		printk(KERN_DEBUG "Bad block table at page %d, version 0x%02X\n",
-		       md->pages[0], md->version[0]);
+		pr_info("Bad block table at page %d, version 0x%02X\n",
+			 md->pages[0], md->version[0]);
 	}
 	return 1;
 }
 
-/*
- * Scan a given block full
- */
+/* Scan a given block full */
 static int scan_block_full(struct mtd_info *mtd, struct nand_bbt_descr *bd,
 			   loff_t offs, uint8_t *buf, size_t readlen,
 			   int scanlen, int len)
@@ -447,7 +405,8 @@ static int scan_block_full(struct mtd_info *mtd, struct nand_bbt_descr *bd,
 	int ret, j;
 
 	ret = scan_read_raw_oob(mtd, buf, offs, readlen);
-	if (ret)
+	/* Ignore ECC errors when checking for BBM */
+	if (ret && !mtd_is_bitflip_or_eccerr(ret))
 		return ret;
 
 	for (j = 0; j < len; j++, buf += scanlen) {
@@ -457,9 +416,7 @@ static int scan_block_full(struct mtd_info *mtd, struct nand_bbt_descr *bd,
 	return 0;
 }
 
-/*
- * Scan a given block partially
- */
+/* Scan a given block partially */
 static int scan_block_fast(struct mtd_info *mtd, struct nand_bbt_descr *bd,
 			   loff_t offs, uint8_t *buf, int len)
 {
@@ -470,16 +427,16 @@ static int scan_block_fast(struct mtd_info *mtd, struct nand_bbt_descr *bd,
 	ops.oobbuf = buf;
 	ops.ooboffs = 0;
 	ops.datbuf = NULL;
-	ops.mode = MTD_OOB_PLACE;
+	ops.mode = MTD_OPS_PLACE_OOB;
 
 	for (j = 0; j < len; j++) {
 		/*
-		 * Read the full oob until read_oob is fixed to
-		 * handle single byte reads for 16 bit
-		 * buswidth
+		 * Read the full oob until read_oob is fixed to handle single
+		 * byte reads for 16 bit buswidth.
 		 */
 		ret = mtd->read_oob(mtd, offs, &ops);
-		if (ret)
+		/* Ignore ECC errors when checking for BBM */
+		if (ret && !mtd_is_bitflip_or_eccerr(ret))
 			return ret;
 
 		if (check_short_pattern(buf, bd))
@@ -492,14 +449,14 @@ static int scan_block_fast(struct mtd_info *mtd, struct nand_bbt_descr *bd,
 
 /**
  * create_bbt - [GENERIC] Create a bad block table by scanning the device
- * @mtd:	MTD device structure
- * @buf:	temporary buffer
- * @bd:		descriptor for the good/bad block search pattern
- * @chip:	create the table for a specific chip, -1 read all chips.
- *		Applies only if NAND_BBT_PERCHIP option is set
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @bd: descriptor for the good/bad block search pattern
+ * @chip: create the table for a specific chip, -1 read all chips; applies only
+ *        if NAND_BBT_PERCHIP option is set
  *
- * Create a bad block table by scanning the device
- * for the given good/bad block identify pattern
+ * Create a bad block table by scanning the device for the given good/bad block
+ * identify pattern.
  */
 static int create_bbt(struct mtd_info *mtd, uint8_t *buf,
 	struct nand_bbt_descr *bd, int chip)
@@ -510,7 +467,7 @@ static int create_bbt(struct mtd_info *mtd, uint8_t *buf,
 	loff_t from;
 	size_t readlen;
 
-	printk(KERN_INFO "Scanning device for bad blocks\n");
+	pr_info("Scanning device for bad blocks\n");
 
 	if (bd->options & NAND_BBT_SCANALLPAGES)
 		len = 1 << (this->bbt_erase_shift - this->page_shift);
@@ -530,14 +487,16 @@ static int create_bbt(struct mtd_info *mtd, uint8_t *buf,
 	}
 
 	if (chip == -1) {
-		/* Note that numblocks is 2 * (real numblocks) here, see i+=2
-		 * below as it makes shifting and masking less painful */
+		/*
+		 * Note that numblocks is 2 * (real numblocks) here, see i+=2
+		 * below as it makes shifting and masking less painful
+		 */
 		numblocks = mtd->size >> (this->bbt_erase_shift - 1);
 		startblock = 0;
 		from = 0;
 	} else {
 		if (chip >= this->numchips) {
-			printk(KERN_WARNING "create_bbt(): chipnr (%d) > available chips (%d)\n",
+			pr_warn("create_bbt(): chipnr (%d) > available chips (%d)\n",
 			       chip + 1, this->numchips);
 			return -EINVAL;
 		}
@@ -547,7 +506,7 @@ static int create_bbt(struct mtd_info *mtd, uint8_t *buf,
 		from = (loff_t)startblock << (this->bbt_erase_shift - 1);
 	}
 
-	if (this->options & NAND_BBT_SCANLASTPAGE)
+	if (this->bbt_options & NAND_BBT_SCANLASTPAGE)
 		from += mtd->erasesize - (mtd->writesize * len);
 
 	for (i = startblock; i < numblocks;) {
@@ -566,8 +525,8 @@ static int create_bbt(struct mtd_info *mtd, uint8_t *buf,
 
 		if (ret) {
 			this->bbt[i >> 3] |= 0x03 << (i & 0x6);
-			printk(KERN_WARNING "Bad eraseblock %d at 0x%012llx\n",
-			       i >> 1, (unsigned long long)from);
+			pr_warn("Bad eraseblock %d at 0x%012llx\n",
+				i >> 1, (unsigned long long)from);
 			mtd->ecc_stats.badblocks++;
 		}
 
@@ -579,20 +538,18 @@ static int create_bbt(struct mtd_info *mtd, uint8_t *buf,
 
 /**
  * search_bbt - [GENERIC] scan the device for a specific bad block table
- * @mtd:	MTD device structure
- * @buf:	temporary buffer
- * @td:		descriptor for the bad block table
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @td: descriptor for the bad block table
  *
- * Read the bad block table by searching for a given ident pattern.
- * Search is preformed either from the beginning up or from the end of
- * the device downwards. The search starts always at the start of a
- * block.
- * If the option NAND_BBT_PERCHIP is given, each chip is searched
- * for a bbt, which contains the bad block information of this chip.
- * This is necessary to provide support for certain DOC devices.
+ * Read the bad block table by searching for a given ident pattern. Search is
+ * preformed either from the beginning up or from the end of the device
+ * downwards. The search starts always at the start of a block. If the option
+ * NAND_BBT_PERCHIP is given, each chip is searched for a bbt, which contains
+ * the bad block information of this chip. This is necessary to provide support
+ * for certain DOC devices.
  *
- * The bbt ident pattern resides in the oob area of the first page
- * in a block.
+ * The bbt ident pattern resides in the oob area of the first page in a block.
  */
 static int search_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *td)
 {
@@ -603,7 +560,7 @@ static int search_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr
 	int bbtblocks;
 	int blocktopage = this->bbt_erase_shift - this->page_shift;
 
-	/* Search direction top -> down ? */
+	/* Search direction top -> down? */
 	if (td->options & NAND_BBT_LASTBLOCK) {
 		startblock = (mtd->size >> this->bbt_erase_shift) - 1;
 		dir = -1;
@@ -612,7 +569,7 @@ static int search_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr
 		dir = 1;
 	}
 
-	/* Do we have a bbt per chip ? */
+	/* Do we have a bbt per chip? */
 	if (td->options & NAND_BBT_PERCHIP) {
 		chips = this->numchips;
 		bbtblocks = this->chipsize >> this->bbt_erase_shift;
@@ -651,23 +608,23 @@ static int search_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr
 	/* Check, if we found a bbt for each requested chip */
 	for (i = 0; i < chips; i++) {
 		if (td->pages[i] == -1)
-			printk(KERN_WARNING "Bad block table not found for chip %d\n", i);
+			pr_warn("Bad block table not found for chip %d\n", i);
 		else
-			printk(KERN_DEBUG "Bad block table found at page %d, version 0x%02X\n", td->pages[i],
-			       td->version[i]);
+			pr_info("Bad block table found at page %d, version "
+				 "0x%02X\n", td->pages[i], td->version[i]);
 	}
 	return 0;
 }
 
 /**
  * search_read_bbts - [GENERIC] scan the device for bad block table(s)
- * @mtd:	MTD device structure
- * @buf:	temporary buffer
- * @td:		descriptor for the bad block table
- * @md:		descriptor for the bad block table mirror
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @td: descriptor for the bad block table
+ * @md: descriptor for the bad block table mirror
  *
- * Search and read the bad block table(s)
-*/
+ * Search and read the bad block table(s).
+ */
 static int search_read_bbts(struct mtd_info *mtd, uint8_t * buf, struct nand_bbt_descr *td, struct nand_bbt_descr *md)
 {
 	/* Search the primary table */
@@ -683,16 +640,14 @@ static int search_read_bbts(struct mtd_info *mtd, uint8_t * buf, struct nand_bbt
 
 /**
  * write_bbt - [GENERIC] (Re)write the bad block table
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @td: descriptor for the bad block table
+ * @md: descriptor for the bad block table mirror
+ * @chipsel: selector for a specific chip, -1 for all
  *
- * @mtd:	MTD device structure
- * @buf:	temporary buffer
- * @td:		descriptor for the bad block table
- * @md:		descriptor for the bad block table mirror
- * @chipsel:	selector for a specific chip, -1 for all
- *
- * (Re)write the bad block table
- *
-*/
+ * (Re)write the bad block table.
+ */
 static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
 		     struct nand_bbt_descr *td, struct nand_bbt_descr *md,
 		     int chipsel)
@@ -711,14 +666,14 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
 	ops.ooblen = mtd->oobsize;
 	ops.ooboffs = 0;
 	ops.datbuf = NULL;
-	ops.mode = MTD_OOB_PLACE;
+	ops.mode = MTD_OPS_PLACE_OOB;
 
 	if (!rcode)
 		rcode = 0xff;
-	/* Write bad block table per chip rather than per device ? */
+	/* Write bad block table per chip rather than per device? */
 	if (td->options & NAND_BBT_PERCHIP) {
 		numblocks = (int)(this->chipsize >> this->bbt_erase_shift);
-		/* Full device write or specific chip ? */
+		/* Full device write or specific chip? */
 		if (chipsel == -1) {
 			nrchips = this->numchips;
 		} else {
@@ -732,8 +687,8 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
 
 	/* Loop through the chips */
 	for (; chip < nrchips; chip++) {
-
-		/* There was already a version of the table, reuse the page
+		/*
+		 * There was already a version of the table, reuse the page
 		 * This applies for absolute placement too, as we have the
 		 * page nr. in td->pages.
 		 */
@@ -742,8 +697,10 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
 			goto write;
 		}
 
-		/* Automatic placement of the bad block table */
-		/* Search direction top -> down ? */
+		/*
+		 * Automatic placement of the bad block table. Search direction
+		 * top -> down?
+		 */
 		if (td->options & NAND_BBT_LASTBLOCK) {
 			startblock = numblocks * (chip + 1) - 1;
 			dir = -1;
@@ -767,7 +724,7 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
 			if (!md || md->pages[chip] != page)
 				goto write;
 		}
-		printk(KERN_ERR "No space left to write bad block table\n");
+		pr_err("No space left to write bad block table\n");
 		return -ENOSPC;
 	write:
 
@@ -792,24 +749,22 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
 
 		bbtoffs = chip * (numblocks >> 2);
 
-		to = ((loff_t) page) << this->page_shift;
+		to = ((loff_t)page) << this->page_shift;
 
-		/* Must we save the block contents ? */
+		/* Must we save the block contents? */
 		if (td->options & NAND_BBT_SAVECONTENT) {
 			/* Make it block aligned */
-			to &= ~((loff_t) ((1 << this->bbt_erase_shift) - 1));
+			to &= ~((loff_t)((1 << this->bbt_erase_shift) - 1));
 			len = 1 << this->bbt_erase_shift;
 			res = mtd->read(mtd, to, len, &retlen, buf);
 			if (res < 0) {
 				if (retlen != len) {
-					printk(KERN_INFO "nand_bbt: Error "
-					       "reading block for writing "
-					       "the bad block table\n");
+					pr_info("nand_bbt: error reading block "
+						"for writing the bad block table\n");
 					return res;
 				}
-				printk(KERN_WARNING "nand_bbt: ECC error "
-				       "while reading block for writing "
-				       "bad block table\n");
+				pr_warn("nand_bbt: ECC error while reading "
+					"block for writing bad block table\n");
 			}
 			/* Read oob data */
 			ops.ooblen = (len >> this->page_shift) * mtd->oobsize;
@@ -822,19 +777,19 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
 			pageoffs = page - (int)(to >> this->page_shift);
 			offs = pageoffs << this->page_shift;
 			/* Preset the bbt area with 0xff */
-			memset(&buf[offs], 0xff, (size_t) (numblocks >> sft));
+			memset(&buf[offs], 0xff, (size_t)(numblocks >> sft));
 			ooboffs = len + (pageoffs * mtd->oobsize);
 
 		} else if (td->options & NAND_BBT_NO_OOB) {
 			ooboffs = 0;
 			offs = td->len;
-			/* the version byte */
+			/* The version byte */
 			if (td->options & NAND_BBT_VERSION)
 				offs++;
 			/* Calc length */
-			len = (size_t) (numblocks >> sft);
+			len = (size_t)(numblocks >> sft);
 			len += offs;
-			/* Make it page aligned ! */
+			/* Make it page aligned! */
 			len = ALIGN(len, mtd->writesize);
 			/* Preset the buffer with 0xff */
 			memset(buf, 0xff, len);
@@ -842,8 +797,8 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
 			memcpy(buf, td->pattern, td->len);
 		} else {
 			/* Calc length */
-			len = (size_t) (numblocks >> sft);
-			/* Make it page aligned ! */
+			len = (size_t)(numblocks >> sft);
+			/* Make it page aligned! */
 			len = ALIGN(len, mtd->writesize);
 			/* Preset the buffer with 0xff */
 			memset(buf, 0xff, len +
@@ -857,13 +812,13 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
 		if (td->options & NAND_BBT_VERSION)
 			buf[ooboffs + td->veroffs] = td->version[chip];
 
-		/* walk through the memory table */
+		/* Walk through the memory table */
 		for (i = 0; i < numblocks;) {
 			uint8_t dat;
 			dat = this->bbt[bbtoffs + (i >> 2)];
 			for (j = 0; j < 4; j++, i++) {
 				int sftcnt = (i << (3 - sft)) & sftmsk;
-				/* Do not store the reserved bbt blocks ! */
+				/* Do not store the reserved bbt blocks! */
 				buf[offs + (i >> sft)] &=
 					~(msk[dat & 0x03] << sftcnt);
 				dat >>= 2;
@@ -884,8 +839,8 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
 		if (res < 0)
 			goto outerr;
 
-		printk(KERN_DEBUG "Bad block table written to 0x%012llx, version "
-		       "0x%02X\n", (unsigned long long)to, td->version[chip]);
+		pr_info("Bad block table written to 0x%012llx, version 0x%02X\n",
+			 (unsigned long long)to, td->version[chip]);
 
 		/* Mark it as used */
 		td->pages[chip] = page;
@@ -893,19 +848,18 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
 	return 0;
 
  outerr:
-	printk(KERN_WARNING
-	       "nand_bbt: Error while writing bad block table %d\n", res);
+	pr_warn("nand_bbt: error while writing bad block table %d\n", res);
 	return res;
 }
 
 /**
  * nand_memory_bbt - [GENERIC] create a memory based bad block table
- * @mtd:	MTD device structure
- * @bd:		descriptor for the good/bad block search pattern
+ * @mtd: MTD device structure
+ * @bd: descriptor for the good/bad block search pattern
  *
- * The function creates a memory based bbt by scanning the device
- * for manufacturer / software marked good / bad blocks
-*/
+ * The function creates a memory based bbt by scanning the device for
+ * manufacturer / software marked good / bad blocks.
+ */
 static inline int nand_memory_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd)
 {
 	struct nand_chip *this = mtd->priv;
@@ -916,25 +870,24 @@ static inline int nand_memory_bbt(struct mtd_info *mtd, struct nand_bbt_descr *b
 
 /**
  * check_create - [GENERIC] create and write bbt(s) if necessary
- * @mtd:	MTD device structure
- * @buf:	temporary buffer
- * @bd:		descriptor for the good/bad block search pattern
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @bd: descriptor for the good/bad block search pattern
  *
- * The function checks the results of the previous call to read_bbt
- * and creates / updates the bbt(s) if necessary
- * Creation is necessary if no bbt was found for the chip/device
- * Update is necessary if one of the tables is missing or the
- * version nr. of one table is less than the other
-*/
+ * The function checks the results of the previous call to read_bbt and creates
+ * / updates the bbt(s) if necessary. Creation is necessary if no bbt was found
+ * for the chip/device. Update is necessary if one of the tables is missing or
+ * the version nr. of one table is less than the other.
+ */
 static int check_create(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *bd)
 {
-	int i, chips, writeops, chipsel, res;
+	int i, chips, writeops, create, chipsel, res, res2;
 	struct nand_chip *this = mtd->priv;
 	struct nand_bbt_descr *td = this->bbt_td;
 	struct nand_bbt_descr *md = this->bbt_md;
 	struct nand_bbt_descr *rd, *rd2;
 
-	/* Do we have a bbt per chip ? */
+	/* Do we have a bbt per chip? */
 	if (td->options & NAND_BBT_PERCHIP)
 		chips = this->numchips;
 	else
@@ -942,86 +895,98 @@ static int check_create(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_desc
 
 	for (i = 0; i < chips; i++) {
 		writeops = 0;
+		create = 0;
 		rd = NULL;
 		rd2 = NULL;
-		/* Per chip or per device ? */
+		res = res2 = 0;
+		/* Per chip or per device? */
 		chipsel = (td->options & NAND_BBT_PERCHIP) ? i : -1;
-		/* Mirrored table available ? */
+		/* Mirrored table available? */
 		if (md) {
 			if (td->pages[i] == -1 && md->pages[i] == -1) {
+				create = 1;
 				writeops = 0x03;
-				goto create;
-			}
-
-			if (td->pages[i] == -1) {
+			} else if (td->pages[i] == -1) {
 				rd = md;
-				td->version[i] = md->version[i];
-				writeops = 1;
-				goto writecheck;
-			}
-
-			if (md->pages[i] == -1) {
+				writeops = 0x01;
+			} else if (md->pages[i] == -1) {
 				rd = td;
-				md->version[i] = td->version[i];
-				writeops = 2;
-				goto writecheck;
-			}
-
-			if (td->version[i] == md->version[i]) {
+				writeops = 0x02;
+			} else if (td->version[i] == md->version[i]) {
 				rd = td;
 				if (!(td->options & NAND_BBT_VERSION))
 					rd2 = md;
-				goto writecheck;
-			}
-
-			if (((int8_t) (td->version[i] - md->version[i])) > 0) {
+			} else if (((int8_t)(td->version[i] - md->version[i])) > 0) {
 				rd = td;
-				md->version[i] = td->version[i];
-				writeops = 2;
+				writeops = 0x02;
 			} else {
 				rd = md;
-				td->version[i] = md->version[i];
-				writeops = 1;
+				writeops = 0x01;
 			}
-
-			goto writecheck;
-
 		} else {
 			if (td->pages[i] == -1) {
+				create = 1;
 				writeops = 0x01;
-				goto create;
+			} else {
+				rd = td;
 			}
-			rd = td;
-			goto writecheck;
 		}
-	create:
-		/* Create the bad block table by scanning the device ? */
-		if (!(td->options & NAND_BBT_CREATE))
-			continue;
 
-		/* Create the table in memory by scanning the chip(s) */
-		if (!(this->options & NAND_CREATE_EMPTY_BBT))
-			create_bbt(mtd, buf, bd, chipsel);
-
-		td->version[i] = 1;
-		if (md)
-			md->version[i] = 1;
-	writecheck:
-		/* read back first ? */
-		if (rd)
-			read_abs_bbt(mtd, buf, rd, chipsel);
-		/* If they weren't versioned, read both. */
-		if (rd2)
-			read_abs_bbt(mtd, buf, rd2, chipsel);
-
-		/* Write the bad block table to the device ? */
+		if (create) {
+			/* Create the bad block table by scanning the device? */
+			if (!(td->options & NAND_BBT_CREATE))
+				continue;
+
+			/* Create the table in memory by scanning the chip(s) */
+			if (!(this->bbt_options & NAND_BBT_CREATE_EMPTY))
+				create_bbt(mtd, buf, bd, chipsel);
+
+			td->version[i] = 1;
+			if (md)
+				md->version[i] = 1;
+		}
+
+		/* Read back first? */
+		if (rd) {
+			res = read_abs_bbt(mtd, buf, rd, chipsel);
+			if (mtd_is_eccerr(res)) {
+				/* Mark table as invalid */
+				rd->pages[i] = -1;
+				rd->version[i] = 0;
+				i--;
+				continue;
+			}
+		}
+		/* If they weren't versioned, read both */
+		if (rd2) {
+			res2 = read_abs_bbt(mtd, buf, rd2, chipsel);
+			if (mtd_is_eccerr(res2)) {
+				/* Mark table as invalid */
+				rd2->pages[i] = -1;
+				rd2->version[i] = 0;
+				i--;
+				continue;
+			}
+		}
+
+		/* Scrub the flash table(s)? */
+		if (mtd_is_bitflip(res) || mtd_is_bitflip(res2))
+			writeops = 0x03;
+
+		/* Update version numbers before writing */
+		if (md) {
+			td->version[i] = max(td->version[i], md->version[i]);
+			md->version[i] = td->version[i];
+		}
+
+		/* Write the bad block table to the device? */
 		if ((writeops & 0x01) && (td->options & NAND_BBT_WRITE)) {
 			res = write_bbt(mtd, buf, td, md, chipsel);
 			if (res < 0)
 				return res;
 		}
 
-		/* Write the mirror bad block table to the device ? */
+		/* Write the mirror bad block table to the device? */
 		if ((writeops & 0x02) && md && (md->options & NAND_BBT_WRITE)) {
 			res = write_bbt(mtd, buf, md, td, chipsel);
 			if (res < 0)
@@ -1033,20 +998,19 @@ static int check_create(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_desc
 
 /**
  * mark_bbt_regions - [GENERIC] mark the bad block table regions
- * @mtd:	MTD device structure
- * @td:		bad block table descriptor
+ * @mtd: MTD device structure
+ * @td: bad block table descriptor
  *
- * The bad block table regions are marked as "bad" to prevent
- * accidental erasures / writes. The regions are identified by
- * the mark 0x02.
-*/
+ * The bad block table regions are marked as "bad" to prevent accidental
+ * erasures / writes. The regions are identified by the mark 0x02.
+ */
 static void mark_bbt_region(struct mtd_info *mtd, struct nand_bbt_descr *td)
 {
 	struct nand_chip *this = mtd->priv;
 	int i, j, chips, block, nrblocks, update;
 	uint8_t oldval, newval;
 
-	/* Do we have a bbt per chip ? */
+	/* Do we have a bbt per chip? */
 	if (td->options & NAND_BBT_PERCHIP) {
 		chips = this->numchips;
 		nrblocks = (int)(this->chipsize >> this->bbt_erase_shift);
@@ -1083,9 +1047,11 @@ static void mark_bbt_region(struct mtd_info *mtd, struct nand_bbt_descr *td)
 				update = 1;
 			block += 2;
 		}
-		/* If we want reserved blocks to be recorded to flash, and some
-		   new ones have been marked, then we need to update the stored
-		   bbts.  This should only happen once. */
+		/*
+		 * If we want reserved blocks to be recorded to flash, and some
+		 * new ones have been marked, then we need to update the stored
+		 * bbts.  This should only happen once.
+		 */
 		if (update && td->reserved_block_code)
 			nand_update_bbt(mtd, (loff_t)(block - 2) << (this->bbt_erase_shift - 1));
 	}
@@ -1093,8 +1059,8 @@ static void mark_bbt_region(struct mtd_info *mtd, struct nand_bbt_descr *td)
 
 /**
  * verify_bbt_descr - verify the bad block description
- * @mtd:	MTD device structure
- * @bd:		the table to verify
+ * @mtd: MTD device structure
+ * @bd: the table to verify
  *
  * This functions performs a few sanity checks on the bad block description
  * table.
@@ -1112,16 +1078,16 @@ static void verify_bbt_descr(struct mtd_info *mtd, struct nand_bbt_descr *bd)
 	pattern_len = bd->len;
 	bits = bd->options & NAND_BBT_NRBITS_MSK;
 
-	BUG_ON((this->options & NAND_USE_FLASH_BBT_NO_OOB) &&
-			!(this->options & NAND_USE_FLASH_BBT));
+	BUG_ON((this->bbt_options & NAND_BBT_NO_OOB) &&
+			!(this->bbt_options & NAND_BBT_USE_FLASH));
 	BUG_ON(!bits);
 
 	if (bd->options & NAND_BBT_VERSION)
 		pattern_len++;
 
 	if (bd->options & NAND_BBT_NO_OOB) {
-		BUG_ON(!(this->options & NAND_USE_FLASH_BBT));
-		BUG_ON(!(this->options & NAND_USE_FLASH_BBT_NO_OOB));
+		BUG_ON(!(this->bbt_options & NAND_BBT_USE_FLASH));
+		BUG_ON(!(this->bbt_options & NAND_BBT_NO_OOB));
 		BUG_ON(bd->offs);
 		if (bd->options & NAND_BBT_VERSION)
 			BUG_ON(bd->veroffs != bd->len);
@@ -1141,18 +1107,16 @@ static void verify_bbt_descr(struct mtd_info *mtd, struct nand_bbt_descr *bd)
 
 /**
  * nand_scan_bbt - [NAND Interface] scan, find, read and maybe create bad block table(s)
- * @mtd:	MTD device structure
- * @bd:		descriptor for the good/bad block search pattern
- *
- * The function checks, if a bad block table(s) is/are already
- * available. If not it scans the device for manufacturer
- * marked good / bad blocks and writes the bad block table(s) to
- * the selected place.
+ * @mtd: MTD device structure
+ * @bd: descriptor for the good/bad block search pattern
  *
- * The bad block table memory is allocated here. It must be freed
- * by calling the nand_free_bbt function.
+ * The function checks, if a bad block table(s) is/are already available. If
+ * not it scans the device for manufacturer marked good / bad blocks and writes
+ * the bad block table(s) to the selected place.
  *
-*/
+ * The bad block table memory is allocated here. It must be freed by calling
+ * the nand_free_bbt function.
+ */
 int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd)
 {
 	struct nand_chip *this = mtd->priv;
@@ -1162,19 +1126,21 @@ int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd)
 	struct nand_bbt_descr *md = this->bbt_md;
 
 	len = mtd->size >> (this->bbt_erase_shift + 2);
-	/* Allocate memory (2bit per block) and clear the memory bad block table */
+	/*
+	 * Allocate memory (2bit per block) and clear the memory bad block
+	 * table.
+	 */
 	this->bbt = kzalloc(len, GFP_KERNEL);
-	if (!this->bbt) {
-		printk(KERN_ERR "nand_scan_bbt: Out of memory\n");
+	if (!this->bbt)
 		return -ENOMEM;
-	}
 
-	/* If no primary table decriptor is given, scan the device
-	 * to build a memory based bad block table
+	/*
+	 * If no primary table decriptor is given, scan the device to build a
+	 * memory based bad block table.
 	 */
 	if (!td) {
 		if ((res = nand_memory_bbt(mtd, bd))) {
-			printk(KERN_ERR "nand_bbt: Can't scan flash and build the RAM-based BBT\n");
+			pr_err("nand_bbt: can't scan flash and build the RAM-based BBT\n");
 			kfree(this->bbt);
 			this->bbt = NULL;
 		}
@@ -1188,13 +1154,12 @@ int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd)
 	len += (len >> this->page_shift) * mtd->oobsize;
 	buf = vmalloc(len);
 	if (!buf) {
-		printk(KERN_ERR "nand_bbt: Out of memory\n");
 		kfree(this->bbt);
 		this->bbt = NULL;
 		return -ENOMEM;
 	}
 
-	/* Is the bbt at a given page ? */
+	/* Is the bbt at a given page? */
 	if (td->options & NAND_BBT_ABSPAGE) {
 		res = read_abs_bbts(mtd, buf, td, md);
 	} else {
@@ -1216,15 +1181,15 @@ int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd)
 
 /**
  * nand_update_bbt - [NAND Interface] update bad block table(s)
- * @mtd:	MTD device structure
- * @offs:	the offset of the newly marked block
+ * @mtd: MTD device structure
+ * @offs: the offset of the newly marked block
  *
- * The function updates the bad block table(s)
-*/
+ * The function updates the bad block table(s).
+ */
 int nand_update_bbt(struct mtd_info *mtd, loff_t offs)
 {
 	struct nand_chip *this = mtd->priv;
-	int len, res = 0, writeops = 0;
+	int len, res = 0;
 	int chip, chipsel;
 	uint8_t *buf;
 	struct nand_bbt_descr *td = this->bbt_td;
@@ -1237,14 +1202,10 @@ int nand_update_bbt(struct mtd_info *mtd, loff_t offs)
 	len = (1 << this->bbt_erase_shift);
 	len += (len >> this->page_shift) * mtd->oobsize;
 	buf = kmalloc(len, GFP_KERNEL);
-	if (!buf) {
-		printk(KERN_ERR "nand_update_bbt: Out of memory\n");
+	if (!buf)
 		return -ENOMEM;
-	}
-
-	writeops = md != NULL ? 0x03 : 0x01;
 
-	/* Do we have a bbt per chip ? */
+	/* Do we have a bbt per chip? */
 	if (td->options & NAND_BBT_PERCHIP) {
 		chip = (int)(offs >> this->chip_shift);
 		chipsel = chip;
@@ -1257,14 +1218,14 @@ int nand_update_bbt(struct mtd_info *mtd, loff_t offs)
 	if (md)
 		md->version[chip]++;
 
-	/* Write the bad block table to the device ? */
-	if ((writeops & 0x01) && (td->options & NAND_BBT_WRITE)) {
+	/* Write the bad block table to the device? */
+	if (td->options & NAND_BBT_WRITE) {
 		res = write_bbt(mtd, buf, td, md, chipsel);
 		if (res < 0)
 			goto out;
 	}
-	/* Write the mirror bad block table to the device ? */
-	if ((writeops & 0x02) && md && (md->options & NAND_BBT_WRITE)) {
+	/* Write the mirror bad block table to the device? */
+	if (md && (md->options & NAND_BBT_WRITE)) {
 		res = write_bbt(mtd, buf, md, td, chipsel);
 	}
 
@@ -1273,8 +1234,10 @@ int nand_update_bbt(struct mtd_info *mtd, loff_t offs)
 	return res;
 }
 
-/* Define some generic bad / good block scan pattern which are used
- * while scanning a device for factory marked good / bad blocks. */
+/*
+ * Define some generic bad / good block scan pattern which are used
+ * while scanning a device for factory marked good / bad blocks.
+ */
 static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
 
 static uint8_t scan_agand_pattern[] = { 0x1C, 0x71, 0xC7, 0x1C, 0x71, 0xC7 };
@@ -1286,8 +1249,7 @@ static struct nand_bbt_descr agand_flashbased = {
 	.pattern = scan_agand_pattern
 };
 
-/* Generic flash bbt decriptors
-*/
+/* Generic flash bbt descriptors */
 static uint8_t bbt_pattern[] = {'B', 'b', 't', '0' };
 static uint8_t mirror_pattern[] = {'1', 't', 'b', 'B' };
 
@@ -1331,31 +1293,27 @@ static struct nand_bbt_descr bbt_mirror_no_bbt_descr = {
 	.pattern = mirror_pattern
 };
 
-#define BBT_SCAN_OPTIONS (NAND_BBT_SCANLASTPAGE | NAND_BBT_SCAN2NDPAGE | \
-		NAND_BBT_SCANBYTE1AND6)
+#define BADBLOCK_SCAN_MASK (~NAND_BBT_NO_OOB)
 /**
- * nand_create_default_bbt_descr - [Internal] Creates a BBT descriptor structure
- * @this:	NAND chip to create descriptor for
+ * nand_create_badblock_pattern - [INTERN] Creates a BBT descriptor structure
+ * @this: NAND chip to create descriptor for
  *
  * This function allocates and initializes a nand_bbt_descr for BBM detection
- * based on the properties of "this". The new descriptor is stored in
+ * based on the properties of @this. The new descriptor is stored in
  * this->badblock_pattern. Thus, this->badblock_pattern should be NULL when
  * passed to this function.
- *
  */
-static int nand_create_default_bbt_descr(struct nand_chip *this)
+static int nand_create_badblock_pattern(struct nand_chip *this)
 {
 	struct nand_bbt_descr *bd;
 	if (this->badblock_pattern) {
-		printk(KERN_WARNING "BBT descr already allocated; not replacing.\n");
+		pr_warn("Bad block pattern already allocated; not replacing\n");
 		return -EINVAL;
 	}
 	bd = kzalloc(sizeof(*bd), GFP_KERNEL);
-	if (!bd) {
-		printk(KERN_ERR "nand_create_default_bbt_descr: Out of memory\n");
+	if (!bd)
 		return -ENOMEM;
-	}
-	bd->options = this->options & BBT_SCAN_OPTIONS;
+	bd->options = this->bbt_options & BADBLOCK_SCAN_MASK;
 	bd->offs = this->badblockpos;
 	bd->len = (this->options & NAND_BUSWIDTH_16) ? 2 : 1;
 	bd->pattern = scan_ff_pattern;
@@ -1366,22 +1324,20 @@ static int nand_create_default_bbt_descr(struct nand_chip *this)
 
 /**
  * nand_default_bbt - [NAND Interface] Select a default bad block table for the device
- * @mtd:	MTD device structure
- *
- * This function selects the default bad block table
- * support for the device and calls the nand_scan_bbt function
+ * @mtd: MTD device structure
  *
-*/
+ * This function selects the default bad block table support for the device and
+ * calls the nand_scan_bbt function.
+ */
 int nand_default_bbt(struct mtd_info *mtd)
 {
 	struct nand_chip *this = mtd->priv;
 
-	/* Default for AG-AND. We must use a flash based
-	 * bad block table as the devices have factory marked
-	 * _good_ blocks. Erasing those blocks leads to loss
-	 * of the good / bad information, so we _must_ store
-	 * this information in a good / bad table during
-	 * startup
+	/*
+	 * Default for AG-AND. We must use a flash based bad block table as the
+	 * devices have factory marked _good_ blocks. Erasing those blocks
+	 * leads to loss of the good / bad information, so we _must_ store this
+	 * information in a good / bad table during startup.
 	 */
 	if (this->options & NAND_IS_AND) {
 		/* Use the default pattern descriptors */
@@ -1389,15 +1345,15 @@ int nand_default_bbt(struct mtd_info *mtd)
 			this->bbt_td = &bbt_main_descr;
 			this->bbt_md = &bbt_mirror_descr;
 		}
-		this->options |= NAND_USE_FLASH_BBT;
+		this->bbt_options |= NAND_BBT_USE_FLASH;
 		return nand_scan_bbt(mtd, &agand_flashbased);
 	}
 
-	/* Is a flash based bad block table requested ? */
-	if (this->options & NAND_USE_FLASH_BBT) {
+	/* Is a flash based bad block table requested? */
+	if (this->bbt_options & NAND_BBT_USE_FLASH) {
 		/* Use the default pattern descriptors */
 		if (!this->bbt_td) {
-			if (this->options & NAND_USE_FLASH_BBT_NO_OOB) {
+			if (this->bbt_options & NAND_BBT_NO_OOB) {
 				this->bbt_td = &bbt_main_no_bbt_descr;
 				this->bbt_md = &bbt_mirror_no_bbt_descr;
 			} else {
@@ -1411,18 +1367,17 @@ int nand_default_bbt(struct mtd_info *mtd)
 	}
 
 	if (!this->badblock_pattern)
-		nand_create_default_bbt_descr(this);
+		nand_create_badblock_pattern(this);
 
 	return nand_scan_bbt(mtd, this->badblock_pattern);
 }
 
 /**
  * nand_isbad_bbt - [NAND Interface] Check if a block is bad
- * @mtd:	MTD device structure
- * @offs:	offset in the device
- * @allowbbt:	allow access to bad block table region
- *
-*/
+ * @mtd: MTD device structure
+ * @offs: offset in the device
+ * @allowbbt: allow access to bad block table region
+ */
 int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt)
 {
 	struct nand_chip *this = mtd->priv;
@@ -1433,8 +1388,9 @@ int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt)
 	block = (int)(offs >> (this->bbt_erase_shift - 1));
 	res = (this->bbt[block >> 3] >> (block & 0x06)) & 0x03;
 
-	DEBUG(MTD_DEBUG_LEVEL2, "nand_isbad_bbt(): bbt info for offs 0x%08x: (block %d) 0x%02x\n",
-	      (unsigned int)offs, block >> 1, res);
+	pr_debug("nand_isbad_bbt(): bbt info for offs 0x%08x: "
+			"(block %d) 0x%02x\n",
+			(unsigned int)offs, block >> 1, res);
 
 	switch ((int)res) {
 	case 0x00:
diff --git a/drivers/mtd/nand/nand_bch.c b/drivers/mtd/nand/nand_bch.c
index 0f931e757116..3803e0bba23b 100644
--- a/drivers/mtd/nand/nand_bch.c
+++ b/drivers/mtd/nand/nand_bch.c
@@ -93,8 +93,8 @@ int nand_bch_correct_data(struct mtd_info *mtd, unsigned char *buf,
 				buf[errloc[i] >> 3] ^= (1 << (errloc[i] & 7));
 			/* else error in ecc, no action needed */
 
-			DEBUG(MTD_DEBUG_LEVEL0, "%s: corrected bitflip %u\n",
-			      __func__, errloc[i]);
+			pr_debug("%s: corrected bitflip %u\n", __func__,
+					errloc[i]);
 		}
 	} else if (count < 0) {
 		printk(KERN_ERR "ecc unrecoverable error\n");
diff --git a/drivers/mtd/nand/nand_ecc.c b/drivers/mtd/nand/nand_ecc.c
index 271b8e735e8f..b7cfe0d37121 100644
--- a/drivers/mtd/nand/nand_ecc.c
+++ b/drivers/mtd/nand/nand_ecc.c
@@ -110,7 +110,7 @@ static const char bitsperbyte[256] = {
 
 /*
  * addressbits is a lookup table to filter out the bits from the xor-ed
- * ecc data that identify the faulty location.
+ * ECC data that identify the faulty location.
  * this is only used for repairing parity
  * see the comments in nand_correct_data for more details
  */
@@ -153,7 +153,7 @@ static const char addressbits[256] = {
  * __nand_calculate_ecc - [NAND Interface] Calculate 3-byte ECC for 256/512-byte
  *			 block
  * @buf:	input buffer with raw data
- * @eccsize:	data bytes per ecc step (256 or 512)
+ * @eccsize:	data bytes per ECC step (256 or 512)
  * @code:	output buffer with ECC
  */
 void __nand_calculate_ecc(const unsigned char *buf, unsigned int eccsize,
@@ -348,7 +348,7 @@ void __nand_calculate_ecc(const unsigned char *buf, unsigned int eccsize,
 		rp17 = (par ^ rp16) & 0xff;
 
 	/*
-	 * Finally calculate the ecc bits.
+	 * Finally calculate the ECC bits.
 	 * Again here it might seem that there are performance optimisations
 	 * possible, but benchmarks showed that on the system this is developed
 	 * the code below is the fastest
@@ -436,7 +436,7 @@ EXPORT_SYMBOL(nand_calculate_ecc);
  * @buf:	raw data read from the chip
  * @read_ecc:	ECC from the chip
  * @calc_ecc:	the ECC calculated from raw data
- * @eccsize:	data bytes per ecc step (256 or 512)
+ * @eccsize:	data bytes per ECC step (256 or 512)
  *
  * Detect and correct a 1 bit error for eccsize byte block
  */
@@ -505,7 +505,7 @@ int __nand_correct_data(unsigned char *buf,
 	}
 	/* count nr of bits; use table lookup, faster than calculating it */
 	if ((bitsperbyte[b0] + bitsperbyte[b1] + bitsperbyte[b2]) == 1)
-		return 1;	/* error in ecc data; no action needed */
+		return 1;	/* error in ECC data; no action needed */
 
 	printk(KERN_ERR "uncorrectable error : ");
 	return -1;
diff --git a/drivers/mtd/nand/nandsim.c b/drivers/mtd/nand/nandsim.c
index 357e8c5252a8..34c03be77301 100644
--- a/drivers/mtd/nand/nandsim.c
+++ b/drivers/mtd/nand/nandsim.c
@@ -2273,9 +2273,9 @@ static int __init ns_init_module(void)
 
 	switch (bbt) {
 	case 2:
-		 chip->options |= NAND_USE_FLASH_BBT_NO_OOB;
+		 chip->bbt_options |= NAND_BBT_NO_OOB;
 	case 1:
-		 chip->options |= NAND_USE_FLASH_BBT;
+		 chip->bbt_options |= NAND_BBT_USE_FLASH;
 	case 0:
 		break;
 	default:
diff --git a/drivers/mtd/nand/ndfc.c b/drivers/mtd/nand/ndfc.c
index ea2dea8a9c88..ee1713907b92 100644
--- a/drivers/mtd/nand/ndfc.c
+++ b/drivers/mtd/nand/ndfc.c
@@ -42,7 +42,6 @@ struct ndfc_controller {
 	struct nand_chip chip;
 	int chip_select;
 	struct nand_hw_control ndfc_control;
-	struct mtd_partition *parts;
 };
 
 static struct ndfc_controller ndfc_ctrl[NDFC_MAX_CS];
@@ -159,13 +158,9 @@ static int ndfc_verify_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
 static int ndfc_chip_init(struct ndfc_controller *ndfc,
 			  struct device_node *node)
 {
-#ifdef CONFIG_MTD_CMDLINE_PARTS
-	static const char *part_types[] = { "cmdlinepart", NULL };
-#else
-	static const char *part_types[] = { NULL };
-#endif
 	struct device_node *flash_np;
 	struct nand_chip *chip = &ndfc->chip;
+	struct mtd_part_parser_data ppdata;
 	int ret;
 
 	chip->IO_ADDR_R = ndfc->ndfcbase + NDFC_DATA;
@@ -193,6 +188,7 @@ static int ndfc_chip_init(struct ndfc_controller *ndfc,
 	if (!flash_np)
 		return -ENODEV;
 
+	ppdata->of_node = flash_np;
 	ndfc->mtd.name = kasprintf(GFP_KERNEL, "%s.%s",
 			dev_name(&ndfc->ofdev->dev), flash_np->name);
 	if (!ndfc->mtd.name) {
@@ -204,18 +200,7 @@ static int ndfc_chip_init(struct ndfc_controller *ndfc,
 	if (ret)
 		goto err;
 
-	ret = parse_mtd_partitions(&ndfc->mtd, part_types, &ndfc->parts, 0);
-	if (ret < 0)
-		goto err;
-
-	if (ret == 0) {
-		ret = of_mtd_parse_partitions(&ndfc->ofdev->dev, flash_np,
-					      &ndfc->parts);
-		if (ret < 0)
-			goto err;
-	}
-
-	ret = mtd_device_register(&ndfc->mtd, ndfc->parts, ret);
+	ret = mtd_device_parse_register(&ndfc->mtd, NULL, &ppdata, NULL, 0);
 
 err:
 	of_node_put(flash_np);
@@ -288,6 +273,7 @@ static int __devexit ndfc_remove(struct platform_device *ofdev)
 	struct ndfc_controller *ndfc = dev_get_drvdata(&ofdev->dev);
 
 	nand_release(&ndfc->mtd);
+	kfree(ndfc->mtd.name);
 
 	return 0;
 }
diff --git a/drivers/mtd/nand/nomadik_nand.c b/drivers/mtd/nand/nomadik_nand.c
index b6a5c86ab31e..b463ecfb4c1a 100644
--- a/drivers/mtd/nand/nomadik_nand.c
+++ b/drivers/mtd/nand/nomadik_nand.c
@@ -187,6 +187,7 @@ static int nomadik_nand_remove(struct platform_device *pdev)
 		pdata->exit();
 
 	if (host) {
+		nand_release(&host->mtd);
 		iounmap(host->cmd_va);
 		iounmap(host->data_va);
 		iounmap(host->addr_va);
diff --git a/drivers/mtd/nand/nuc900_nand.c b/drivers/mtd/nand/nuc900_nand.c
index 9c30a0b03171..fa8faedfad6e 100644
--- a/drivers/mtd/nand/nuc900_nand.c
+++ b/drivers/mtd/nand/nuc900_nand.c
@@ -339,6 +339,7 @@ static int __devexit nuc900_nand_remove(struct platform_device *pdev)
 	struct nuc900_nand *nuc900_nand = platform_get_drvdata(pdev);
 	struct resource *res;
 
+	nand_release(&nuc900_nand->mtd);
 	iounmap(nuc900_nand->reg);
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index ec22a5aab038..f745f00f3167 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -95,8 +95,6 @@
 #define P4e_s(a)	(TF(a & NAND_Ecc_P4e)		<< 0)
 #define P4o_s(a)	(TF(a & NAND_Ecc_P4o)		<< 1)
 
-static const char *part_probes[] = { "cmdlinepart", NULL };
-
 /* oob info generated runtime depending on ecc algorithm and layout selected */
 static struct nand_ecclayout omap_oobinfo;
 /* Define some generic bad / good block scan pattern which are used
@@ -115,7 +113,6 @@ struct omap_nand_info {
 	struct nand_hw_control		controller;
 	struct omap_nand_platform_data	*pdata;
 	struct mtd_info			mtd;
-	struct mtd_partition		*parts;
 	struct nand_chip		nand;
 	struct platform_device		*pdev;
 
@@ -745,12 +742,12 @@ static int omap_compare_ecc(u8 *ecc_data1,	/* read from NAND memory */
 
 	case 1:
 		/* Uncorrectable error */
-		DEBUG(MTD_DEBUG_LEVEL0, "ECC UNCORRECTED_ERROR 1\n");
+		pr_debug("ECC UNCORRECTED_ERROR 1\n");
 		return -1;
 
 	case 11:
 		/* UN-Correctable error */
-		DEBUG(MTD_DEBUG_LEVEL0, "ECC UNCORRECTED_ERROR B\n");
+		pr_debug("ECC UNCORRECTED_ERROR B\n");
 		return -1;
 
 	case 12:
@@ -767,8 +764,8 @@ static int omap_compare_ecc(u8 *ecc_data1,	/* read from NAND memory */
 
 		find_bit = (ecc_bit[5] << 2) + (ecc_bit[3] << 1) + ecc_bit[1];
 
-		DEBUG(MTD_DEBUG_LEVEL0, "Correcting single bit ECC error at "
-				"offset: %d, bit: %d\n", find_byte, find_bit);
+		pr_debug("Correcting single bit ECC error at offset: "
+				"%d, bit: %d\n", find_byte, find_bit);
 
 		page_data[find_byte] ^= (1 << find_bit);
 
@@ -780,7 +777,7 @@ static int omap_compare_ecc(u8 *ecc_data1,	/* read from NAND memory */
 			    ecc_data2[2] == 0)
 				return 0;
 		}
-		DEBUG(MTD_DEBUG_LEVEL0, "UNCORRECTED_ERROR default\n");
+		pr_debug("UNCORRECTED_ERROR default\n");
 		return -1;
 	}
 }
@@ -1104,13 +1101,8 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
 		goto out_release_mem_region;
 	}
 
-	err = parse_mtd_partitions(&info->mtd, part_probes, &info->parts, 0);
-	if (err > 0)
-		mtd_device_register(&info->mtd, info->parts, err);
-	else if (pdata->parts)
-		mtd_device_register(&info->mtd, pdata->parts, pdata->nr_parts);
-	else
-		mtd_device_register(&info->mtd, NULL, 0);
+	mtd_device_parse_register(&info->mtd, NULL, 0,
+			pdata->parts, pdata->nr_parts);
 
 	platform_set_drvdata(pdev, &info->mtd);
 
diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
index 7794d0680f91..29f505adaf84 100644
--- a/drivers/mtd/nand/orion_nand.c
+++ b/drivers/mtd/nand/orion_nand.c
@@ -21,8 +21,6 @@
 #include <mach/hardware.h>
 #include <plat/orion_nand.h>
 
-static const char *part_probes[] = { "cmdlinepart", NULL };
-
 static void orion_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
 {
 	struct nand_chip *nc = mtd->priv;
@@ -81,8 +79,6 @@ static int __init orion_nand_probe(struct platform_device *pdev)
 	struct resource *res;
 	void __iomem *io_base;
 	int ret = 0;
-	struct mtd_partition *partitions = NULL;
-	int num_part = 0;
 
 	nc = kzalloc(sizeof(struct nand_chip) + sizeof(struct mtd_info), GFP_KERNEL);
 	if (!nc) {
@@ -132,17 +128,9 @@ static int __init orion_nand_probe(struct platform_device *pdev)
 		goto no_dev;
 	}
 
-#ifdef CONFIG_MTD_CMDLINE_PARTS
 	mtd->name = "orion_nand";
-	num_part = parse_mtd_partitions(mtd, part_probes, &partitions, 0);
-#endif
-	/* If cmdline partitions have been passed, let them be used */
-	if (num_part <= 0) {
-		num_part = board->nr_parts;
-		partitions = board->parts;
-	}
-
-	ret = mtd_device_register(mtd, partitions, num_part);
+	ret = mtd_device_parse_register(mtd, NULL, 0,
+			board->parts, board->nr_parts);
 	if (ret) {
 		nand_release(mtd);
 		goto no_dev;
diff --git a/drivers/mtd/nand/pasemi_nand.c b/drivers/mtd/nand/pasemi_nand.c
index b1aa41b8a4eb..a97264ececdb 100644
--- a/drivers/mtd/nand/pasemi_nand.c
+++ b/drivers/mtd/nand/pasemi_nand.c
@@ -155,7 +155,8 @@ static int __devinit pasemi_nand_probe(struct platform_device *ofdev)
 	chip->ecc.mode = NAND_ECC_SOFT;
 
 	/* Enable the following for a flash based bad block table */
-	chip->options = NAND_USE_FLASH_BBT | NAND_NO_AUTOINCR;
+	chip->options = NAND_NO_AUTOINCR;
+	chip->bbt_options = NAND_BBT_USE_FLASH;
 
 	/* Scan to find existence of the device */
 	if (nand_scan(pasemi_nand_mtd, 1)) {
diff --git a/drivers/mtd/nand/plat_nand.c b/drivers/mtd/nand/plat_nand.c
index 633c04bf76f6..ea8e1234e0e2 100644
--- a/drivers/mtd/nand/plat_nand.c
+++ b/drivers/mtd/nand/plat_nand.c
@@ -21,8 +21,6 @@ struct plat_nand_data {
 	struct nand_chip	chip;
 	struct mtd_info		mtd;
 	void __iomem		*io_base;
-	int			nr_parts;
-	struct mtd_partition	*parts;
 };
 
 /*
@@ -79,6 +77,7 @@ static int __devinit plat_nand_probe(struct platform_device *pdev)
 	data->chip.read_buf = pdata->ctrl.read_buf;
 	data->chip.chip_delay = pdata->chip.chip_delay;
 	data->chip.options |= pdata->chip.options;
+	data->chip.bbt_options |= pdata->chip.bbt_options;
 
 	data->chip.ecc.hwctl = pdata->ctrl.hwcontrol;
 	data->chip.ecc.layout = pdata->chip.ecclayout;
@@ -99,23 +98,9 @@ static int __devinit plat_nand_probe(struct platform_device *pdev)
 		goto out;
 	}
 
-	if (pdata->chip.part_probe_types) {
-		err = parse_mtd_partitions(&data->mtd,
-					pdata->chip.part_probe_types,
-					&data->parts, 0);
-		if (err > 0) {
-			mtd_device_register(&data->mtd, data->parts, err);
-			return 0;
-		}
-	}
-	if (pdata->chip.set_parts)
-		pdata->chip.set_parts(data->mtd.size, &pdata->chip);
-	if (pdata->chip.partitions) {
-		data->parts = pdata->chip.partitions;
-		err = mtd_device_register(&data->mtd, data->parts,
-			pdata->chip.nr_partitions);
-	} else
-		err = mtd_device_register(&data->mtd, NULL, 0);
+	err = mtd_device_parse_register(&data->mtd,
+			pdata->chip.part_probe_types, 0,
+			pdata->chip.partitions, pdata->chip.nr_partitions);
 
 	if (!err)
 		return err;
@@ -145,8 +130,6 @@ static int __devexit plat_nand_remove(struct platform_device *pdev)
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 
 	nand_release(&data->mtd);
-	if (data->parts && data->parts != pdata->chip.partitions)
-		kfree(data->parts);
 	if (pdata->ctrl.remove)
 		pdata->ctrl.remove(pdev);
 	iounmap(data->io_base);
diff --git a/drivers/mtd/nand/ppchameleonevb.c b/drivers/mtd/nand/ppchameleonevb.c
index 3bbb796b451c..7e52af51a198 100644
--- a/drivers/mtd/nand/ppchameleonevb.c
+++ b/drivers/mtd/nand/ppchameleonevb.c
@@ -99,8 +99,6 @@ static struct mtd_partition partition_info_evb[] = {
 
 #define NUM_PARTITIONS 1
 
-extern int parse_cmdline_partitions(struct mtd_info *master, struct mtd_partition **pparts, const char *mtd_id);
-
 /*
  *	hardware specific access to control-lines
  */
@@ -187,18 +185,12 @@ static int ppchameleonevb_device_ready(struct mtd_info *minfo)
 }
 #endif
 
-const char *part_probes[] = { "cmdlinepart", NULL };
-const char *part_probes_evb[] = { "cmdlinepart", NULL };
-
 /*
  * Main initialization routine
  */
 static int __init ppchameleonevb_init(void)
 {
 	struct nand_chip *this;
-	const char *part_type = 0;
-	int mtd_parts_nb = 0;
-	struct mtd_partition *mtd_parts = 0;
 	void __iomem *ppchameleon_fio_base;
 	void __iomem *ppchameleonevb_fio_base;
 
@@ -281,24 +273,13 @@ static int __init ppchameleonevb_init(void)
 #endif
 
 	ppchameleon_mtd->name = "ppchameleon-nand";
-	mtd_parts_nb = parse_mtd_partitions(ppchameleon_mtd, part_probes, &mtd_parts, 0);
-	if (mtd_parts_nb > 0)
-		part_type = "command line";
-	else
-		mtd_parts_nb = 0;
-
-	if (mtd_parts_nb == 0) {
-		if (ppchameleon_mtd->size == NAND_SMALL_SIZE)
-			mtd_parts = partition_info_me;
-		else
-			mtd_parts = partition_info_hi;
-		mtd_parts_nb = NUM_PARTITIONS;
-		part_type = "static";
-	}
 
 	/* Register the partitions */
-	printk(KERN_NOTICE "Using %s partition definition\n", part_type);
-	mtd_device_register(ppchameleon_mtd, mtd_parts, mtd_parts_nb);
+	mtd_device_parse_register(ppchameleon_mtd, NULL, 0,
+			ppchameleon_mtd->size == NAND_SMALL_SIZE ?
+				partition_info_me :
+				partition_info_hi,
+			NUM_PARTITIONS);
 
  nand_evb_init:
 	/****************************
@@ -382,21 +363,13 @@ static int __init ppchameleonevb_init(void)
 	}
 
 	ppchameleonevb_mtd->name = NAND_EVB_MTD_NAME;
-	mtd_parts_nb = parse_mtd_partitions(ppchameleonevb_mtd, part_probes_evb, &mtd_parts, 0);
-	if (mtd_parts_nb > 0)
-		part_type = "command line";
-	else
-		mtd_parts_nb = 0;
-
-	if (mtd_parts_nb == 0) {
-		mtd_parts = partition_info_evb;
-		mtd_parts_nb = NUM_PARTITIONS;
-		part_type = "static";
-	}
 
 	/* Register the partitions */
-	printk(KERN_NOTICE "Using %s partition definition\n", part_type);
-	mtd_device_register(ppchameleonevb_mtd, mtd_parts, mtd_parts_nb);
+	mtd_device_parse_register(ppchameleonevb_mtd, NULL, 0,
+			ppchameleon_mtd->size == NAND_SMALL_SIZE ?
+				partition_info_me :
+				partition_info_hi,
+			NUM_PARTITIONS);
 
 	/* Return happy */
 	return 0;
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 1fb3b3a80581..9eb7f879969e 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -110,6 +110,7 @@ enum {
 
 enum {
 	STATE_IDLE = 0,
+	STATE_PREPARED,
 	STATE_CMD_HANDLE,
 	STATE_DMA_READING,
 	STATE_DMA_WRITING,
@@ -120,21 +121,40 @@ enum {
 	STATE_READY,
 };
 
-struct pxa3xx_nand_info {
-	struct nand_chip	nand_chip;
+struct pxa3xx_nand_host {
+	struct nand_chip	chip;
+	struct pxa3xx_nand_cmdset *cmdset;
+	struct mtd_info         *mtd;
+	void			*info_data;
+
+	/* page size of attached chip */
+	unsigned int		page_size;
+	int			use_ecc;
+	int			cs;
 
+	/* calculated from pxa3xx_nand_flash data */
+	unsigned int		col_addr_cycles;
+	unsigned int		row_addr_cycles;
+	size_t			read_id_bytes;
+
+	/* cached register value */
+	uint32_t		reg_ndcr;
+	uint32_t		ndtr0cs0;
+	uint32_t		ndtr1cs0;
+};
+
+struct pxa3xx_nand_info {
 	struct nand_hw_control	controller;
 	struct platform_device	 *pdev;
-	struct pxa3xx_nand_cmdset *cmdset;
 
 	struct clk		*clk;
 	void __iomem		*mmio_base;
 	unsigned long		mmio_phys;
+	struct completion	cmd_complete;
 
 	unsigned int 		buf_start;
 	unsigned int		buf_count;
 
-	struct mtd_info         *mtd;
 	/* DMA information */
 	int			drcmr_dat;
 	int			drcmr_cmd;
@@ -142,44 +162,27 @@ struct pxa3xx_nand_info {
 	unsigned char		*data_buff;
 	unsigned char		*oob_buff;
 	dma_addr_t 		data_buff_phys;
-	size_t			data_buff_size;
 	int 			data_dma_ch;
 	struct pxa_dma_desc	*data_desc;
 	dma_addr_t 		data_desc_addr;
 
-	uint32_t		reg_ndcr;
-
-	/* saved column/page_addr during CMD_SEQIN */
-	int			seqin_column;
-	int			seqin_page_addr;
-
-	/* relate to the command */
+	struct pxa3xx_nand_host *host[NUM_CHIP_SELECT];
 	unsigned int		state;
 
+	int			cs;
 	int			use_ecc;	/* use HW ECC ? */
 	int			use_dma;	/* use DMA ? */
 	int			is_ready;
 
 	unsigned int		page_size;	/* page size of attached chip */
 	unsigned int		data_size;	/* data size in FIFO */
+	unsigned int		oob_size;
 	int 			retcode;
-	struct completion 	cmd_complete;
 
 	/* generated NDCBx register values */
 	uint32_t		ndcb0;
 	uint32_t		ndcb1;
 	uint32_t		ndcb2;
-
-	/* timing calcuted from setting */
-	uint32_t		ndtr0cs0;
-	uint32_t		ndtr1cs0;
-
-	/* calculated from pxa3xx_nand_flash data */
-	size_t		oob_size;
-	size_t		read_id_bytes;
-
-	unsigned int	col_addr_cycles;
-	unsigned int	row_addr_cycles;
 };
 
 static int use_dma = 1;
@@ -225,7 +228,7 @@ static struct pxa3xx_nand_flash builtin_flash_types[] = {
 /* Define a default flash type setting serve as flash detecting only */
 #define DEFAULT_FLASH_TYPE (&builtin_flash_types[0])
 
-const char *mtd_names[] = {"pxa3xx_nand-0", NULL};
+const char *mtd_names[] = {"pxa3xx_nand-0", "pxa3xx_nand-1", NULL};
 
 #define NDTR0_tCH(c)	(min((c), 7) << 19)
 #define NDTR0_tCS(c)	(min((c), 7) << 16)
@@ -241,9 +244,10 @@ const char *mtd_names[] = {"pxa3xx_nand-0", NULL};
 /* convert nano-seconds to nand flash controller clock cycles */
 #define ns2cycle(ns, clk)	(int)((ns) * (clk / 1000000) / 1000)
 
-static void pxa3xx_nand_set_timing(struct pxa3xx_nand_info *info,
+static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host,
 				   const struct pxa3xx_nand_timing *t)
 {
+	struct pxa3xx_nand_info *info = host->info_data;
 	unsigned long nand_clk = clk_get_rate(info->clk);
 	uint32_t ndtr0, ndtr1;
 
@@ -258,23 +262,24 @@ static void pxa3xx_nand_set_timing(struct pxa3xx_nand_info *info,
 		NDTR1_tWHR(ns2cycle(t->tWHR, nand_clk)) |
 		NDTR1_tAR(ns2cycle(t->tAR, nand_clk));
 
-	info->ndtr0cs0 = ndtr0;
-	info->ndtr1cs0 = ndtr1;
+	host->ndtr0cs0 = ndtr0;
+	host->ndtr1cs0 = ndtr1;
 	nand_writel(info, NDTR0CS0, ndtr0);
 	nand_writel(info, NDTR1CS0, ndtr1);
 }
 
 static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info)
 {
-	int oob_enable = info->reg_ndcr & NDCR_SPARE_EN;
+	struct pxa3xx_nand_host *host = info->host[info->cs];
+	int oob_enable = host->reg_ndcr & NDCR_SPARE_EN;
 
-	info->data_size = info->page_size;
+	info->data_size = host->page_size;
 	if (!oob_enable) {
 		info->oob_size = 0;
 		return;
 	}
 
-	switch (info->page_size) {
+	switch (host->page_size) {
 	case 2048:
 		info->oob_size = (info->use_ecc) ? 40 : 64;
 		break;
@@ -292,9 +297,10 @@ static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info)
  */
 static void pxa3xx_nand_start(struct pxa3xx_nand_info *info)
 {
+	struct pxa3xx_nand_host *host = info->host[info->cs];
 	uint32_t ndcr;
 
-	ndcr = info->reg_ndcr;
+	ndcr = host->reg_ndcr;
 	ndcr |= info->use_ecc ? NDCR_ECC_EN : 0;
 	ndcr |= info->use_dma ? NDCR_DMA_EN : 0;
 	ndcr |= NDCR_ND_RUN;
@@ -359,7 +365,7 @@ static void handle_data_pio(struct pxa3xx_nand_info *info)
 					DIV_ROUND_UP(info->oob_size, 4));
 		break;
 	default:
-		printk(KERN_ERR "%s: invalid state %d\n", __func__,
+		dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
 				info->state);
 		BUG();
 	}
@@ -385,7 +391,7 @@ static void start_data_dma(struct pxa3xx_nand_info *info)
 		desc->dcmd |= DCMD_INCTRGADDR | DCMD_FLOWSRC;
 		break;
 	default:
-		printk(KERN_ERR "%s: invalid state %d\n", __func__,
+		dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
 				info->state);
 		BUG();
 	}
@@ -416,6 +422,15 @@ static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
 {
 	struct pxa3xx_nand_info *info = devid;
 	unsigned int status, is_completed = 0;
+	unsigned int ready, cmd_done;
+
+	if (info->cs == 0) {
+		ready           = NDSR_FLASH_RDY;
+		cmd_done        = NDSR_CS0_CMDD;
+	} else {
+		ready           = NDSR_RDY;
+		cmd_done        = NDSR_CS1_CMDD;
+	}
 
 	status = nand_readl(info, NDSR);
 
@@ -437,11 +452,11 @@ static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
 			handle_data_pio(info);
 		}
 	}
-	if (status & NDSR_CS0_CMDD) {
+	if (status & cmd_done) {
 		info->state = STATE_CMD_DONE;
 		is_completed = 1;
 	}
-	if (status & NDSR_FLASH_RDY) {
+	if (status & ready) {
 		info->is_ready = 1;
 		info->state = STATE_READY;
 	}
@@ -463,12 +478,6 @@ NORMAL_IRQ_EXIT:
 	return IRQ_HANDLED;
 }
 
-static int pxa3xx_nand_dev_ready(struct mtd_info *mtd)
-{
-	struct pxa3xx_nand_info *info = mtd->priv;
-	return (nand_readl(info, NDSR) & NDSR_RDY) ? 1 : 0;
-}
-
 static inline int is_buf_blank(uint8_t *buf, size_t len)
 {
 	for (; len > 0; len--)
@@ -481,10 +490,12 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 		uint16_t column, int page_addr)
 {
 	uint16_t cmd;
-	int addr_cycle, exec_cmd, ndcb0;
-	struct mtd_info *mtd = info->mtd;
+	int addr_cycle, exec_cmd;
+	struct pxa3xx_nand_host *host;
+	struct mtd_info *mtd;
 
-	ndcb0 = 0;
+	host = info->host[info->cs];
+	mtd = host->mtd;
 	addr_cycle = 0;
 	exec_cmd = 1;
 
@@ -495,6 +506,10 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 	info->use_ecc		= 0;
 	info->is_ready		= 0;
 	info->retcode		= ERR_NONE;
+	if (info->cs != 0)
+		info->ndcb0 = NDCB0_CSEL;
+	else
+		info->ndcb0 = 0;
 
 	switch (command) {
 	case NAND_CMD_READ0:
@@ -512,20 +527,19 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 		break;
 	}
 
-	info->ndcb0 = ndcb0;
-	addr_cycle = NDCB0_ADDR_CYC(info->row_addr_cycles
-				    + info->col_addr_cycles);
+	addr_cycle = NDCB0_ADDR_CYC(host->row_addr_cycles
+				    + host->col_addr_cycles);
 
 	switch (command) {
 	case NAND_CMD_READOOB:
 	case NAND_CMD_READ0:
-		cmd = info->cmdset->read1;
+		cmd = host->cmdset->read1;
 		if (command == NAND_CMD_READOOB)
 			info->buf_start = mtd->writesize + column;
 		else
 			info->buf_start = column;
 
-		if (unlikely(info->page_size < PAGE_CHUNK_SIZE))
+		if (unlikely(host->page_size < PAGE_CHUNK_SIZE))
 			info->ndcb0 |= NDCB0_CMD_TYPE(0)
 					| addr_cycle
 					| (cmd & NDCB0_CMD1_MASK);
@@ -537,7 +551,7 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 
 	case NAND_CMD_SEQIN:
 		/* small page addr setting */
-		if (unlikely(info->page_size < PAGE_CHUNK_SIZE)) {
+		if (unlikely(host->page_size < PAGE_CHUNK_SIZE)) {
 			info->ndcb1 = ((page_addr & 0xFFFFFF) << 8)
 					| (column & 0xFF);
 
@@ -564,7 +578,7 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 			break;
 		}
 
-		cmd = info->cmdset->program;
+		cmd = host->cmdset->program;
 		info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
 				| NDCB0_AUTO_RS
 				| NDCB0_ST_ROW_EN
@@ -574,8 +588,8 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 		break;
 
 	case NAND_CMD_READID:
-		cmd = info->cmdset->read_id;
-		info->buf_count = info->read_id_bytes;
+		cmd = host->cmdset->read_id;
+		info->buf_count = host->read_id_bytes;
 		info->ndcb0 |= NDCB0_CMD_TYPE(3)
 				| NDCB0_ADDR_CYC(1)
 				| cmd;
@@ -583,7 +597,7 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 		info->data_size = 8;
 		break;
 	case NAND_CMD_STATUS:
-		cmd = info->cmdset->read_status;
+		cmd = host->cmdset->read_status;
 		info->buf_count = 1;
 		info->ndcb0 |= NDCB0_CMD_TYPE(4)
 				| NDCB0_ADDR_CYC(1)
@@ -593,7 +607,7 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 		break;
 
 	case NAND_CMD_ERASE1:
-		cmd = info->cmdset->erase;
+		cmd = host->cmdset->erase;
 		info->ndcb0 |= NDCB0_CMD_TYPE(2)
 				| NDCB0_AUTO_RS
 				| NDCB0_ADDR_CYC(3)
@@ -604,7 +618,7 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 
 		break;
 	case NAND_CMD_RESET:
-		cmd = info->cmdset->reset;
+		cmd = host->cmdset->reset;
 		info->ndcb0 |= NDCB0_CMD_TYPE(5)
 				| cmd;
 
@@ -616,8 +630,8 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 
 	default:
 		exec_cmd = 0;
-		printk(KERN_ERR "pxa3xx-nand: non-supported"
-			" command %x\n", command);
+		dev_err(&info->pdev->dev, "non-supported command %x\n",
+				command);
 		break;
 	}
 
@@ -627,7 +641,8 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
 				int column, int page_addr)
 {
-	struct pxa3xx_nand_info *info = mtd->priv;
+	struct pxa3xx_nand_host *host = mtd->priv;
+	struct pxa3xx_nand_info *info = host->info_data;
 	int ret, exec_cmd;
 
 	/*
@@ -635,9 +650,21 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
 	 * "byte" address into a "word" address appropriate
 	 * for indexing a word-oriented device
 	 */
-	if (info->reg_ndcr & NDCR_DWIDTH_M)
+	if (host->reg_ndcr & NDCR_DWIDTH_M)
 		column /= 2;
 
+	/*
+	 * There may be different NAND chip hooked to
+	 * different chip select, so check whether
+	 * chip select has been changed, if yes, reset the timing
+	 */
+	if (info->cs != host->cs) {
+		info->cs = host->cs;
+		nand_writel(info, NDTR0CS0, host->ndtr0cs0);
+		nand_writel(info, NDTR1CS0, host->ndtr1cs0);
+	}
+
+	info->state = STATE_PREPARED;
 	exec_cmd = prepare_command_pool(info, command, column, page_addr);
 	if (exec_cmd) {
 		init_completion(&info->cmd_complete);
@@ -646,12 +673,12 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
 		ret = wait_for_completion_timeout(&info->cmd_complete,
 				CHIP_DELAY_TIMEOUT);
 		if (!ret) {
-			printk(KERN_ERR "Wait time out!!!\n");
+			dev_err(&info->pdev->dev, "Wait time out!!!\n");
 			/* Stop State Machine for next command cycle */
 			pxa3xx_nand_stop(info);
 		}
-		info->state = STATE_IDLE;
 	}
+	info->state = STATE_IDLE;
 }
 
 static void pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd,
@@ -664,7 +691,8 @@ static void pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd,
 static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
 		struct nand_chip *chip, uint8_t *buf, int page)
 {
-	struct pxa3xx_nand_info *info = mtd->priv;
+	struct pxa3xx_nand_host *host = mtd->priv;
+	struct pxa3xx_nand_info *info = host->info_data;
 
 	chip->read_buf(mtd, buf, mtd->writesize);
 	chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
@@ -685,6 +713,8 @@ static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
 		 * OOB, ignore such double bit errors
 		 */
 		if (is_buf_blank(buf, mtd->writesize))
+			info->retcode = ERR_NONE;
+		else
 			mtd->ecc_stats.failed++;
 	}
 
@@ -693,7 +723,8 @@ static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
 
 static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd)
 {
-	struct pxa3xx_nand_info *info = mtd->priv;
+	struct pxa3xx_nand_host *host = mtd->priv;
+	struct pxa3xx_nand_info *info = host->info_data;
 	char retval = 0xFF;
 
 	if (info->buf_start < info->buf_count)
@@ -705,7 +736,8 @@ static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd)
 
 static u16 pxa3xx_nand_read_word(struct mtd_info *mtd)
 {
-	struct pxa3xx_nand_info *info = mtd->priv;
+	struct pxa3xx_nand_host *host = mtd->priv;
+	struct pxa3xx_nand_info *info = host->info_data;
 	u16 retval = 0xFFFF;
 
 	if (!(info->buf_start & 0x01) && info->buf_start < info->buf_count) {
@@ -717,7 +749,8 @@ static u16 pxa3xx_nand_read_word(struct mtd_info *mtd)
 
 static void pxa3xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
 {
-	struct pxa3xx_nand_info *info = mtd->priv;
+	struct pxa3xx_nand_host *host = mtd->priv;
+	struct pxa3xx_nand_info *info = host->info_data;
 	int real_len = min_t(size_t, len, info->buf_count - info->buf_start);
 
 	memcpy(buf, info->data_buff + info->buf_start, real_len);
@@ -727,7 +760,8 @@ static void pxa3xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
 static void pxa3xx_nand_write_buf(struct mtd_info *mtd,
 		const uint8_t *buf, int len)
 {
-	struct pxa3xx_nand_info *info = mtd->priv;
+	struct pxa3xx_nand_host *host = mtd->priv;
+	struct pxa3xx_nand_info *info = host->info_data;
 	int real_len = min_t(size_t, len, info->buf_count - info->buf_start);
 
 	memcpy(info->data_buff + info->buf_start, buf, real_len);
@@ -747,7 +781,8 @@ static void pxa3xx_nand_select_chip(struct mtd_info *mtd, int chip)
 
 static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
 {
-	struct pxa3xx_nand_info *info = mtd->priv;
+	struct pxa3xx_nand_host *host = mtd->priv;
+	struct pxa3xx_nand_info *info = host->info_data;
 
 	/* pxa3xx_nand_send_command has waited for command complete */
 	if (this->state == FL_WRITING || this->state == FL_ERASING) {
@@ -770,54 +805,70 @@ static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info,
 {
 	struct platform_device *pdev = info->pdev;
 	struct pxa3xx_nand_platform_data *pdata = pdev->dev.platform_data;
+	struct pxa3xx_nand_host *host = info->host[info->cs];
 	uint32_t ndcr = 0x0; /* enable all interrupts */
 
-	if (f->page_size != 2048 && f->page_size != 512)
+	if (f->page_size != 2048 && f->page_size != 512) {
+		dev_err(&pdev->dev, "Current only support 2048 and 512 size\n");
 		return -EINVAL;
+	}
 
-	if (f->flash_width != 16 && f->flash_width != 8)
+	if (f->flash_width != 16 && f->flash_width != 8) {
+		dev_err(&pdev->dev, "Only support 8bit and 16 bit!\n");
 		return -EINVAL;
+	}
 
 	/* calculate flash information */
-	info->cmdset = &default_cmdset;
-	info->page_size = f->page_size;
-	info->read_id_bytes = (f->page_size == 2048) ? 4 : 2;
+	host->cmdset = &default_cmdset;
+	host->page_size = f->page_size;
+	host->read_id_bytes = (f->page_size == 2048) ? 4 : 2;
 
 	/* calculate addressing information */
-	info->col_addr_cycles = (f->page_size == 2048) ? 2 : 1;
+	host->col_addr_cycles = (f->page_size == 2048) ? 2 : 1;
 
 	if (f->num_blocks * f->page_per_block > 65536)
-		info->row_addr_cycles = 3;
+		host->row_addr_cycles = 3;
 	else
-		info->row_addr_cycles = 2;
+		host->row_addr_cycles = 2;
 
 	ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
-	ndcr |= (info->col_addr_cycles == 2) ? NDCR_RA_START : 0;
+	ndcr |= (host->col_addr_cycles == 2) ? NDCR_RA_START : 0;
 	ndcr |= (f->page_per_block == 64) ? NDCR_PG_PER_BLK : 0;
 	ndcr |= (f->page_size == 2048) ? NDCR_PAGE_SZ : 0;
 	ndcr |= (f->flash_width == 16) ? NDCR_DWIDTH_M : 0;
 	ndcr |= (f->dfc_width == 16) ? NDCR_DWIDTH_C : 0;
 
-	ndcr |= NDCR_RD_ID_CNT(info->read_id_bytes);
+	ndcr |= NDCR_RD_ID_CNT(host->read_id_bytes);
 	ndcr |= NDCR_SPARE_EN; /* enable spare by default */
 
-	info->reg_ndcr = ndcr;
+	host->reg_ndcr = ndcr;
 
-	pxa3xx_nand_set_timing(info, f->timing);
+	pxa3xx_nand_set_timing(host, f->timing);
 	return 0;
 }
 
 static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info)
 {
+	/*
+	 * We set 0 by hard coding here, for we don't support keep_config
+	 * when there is more than one chip attached to the controller
+	 */
+	struct pxa3xx_nand_host *host = info->host[0];
 	uint32_t ndcr = nand_readl(info, NDCR);
-	info->page_size = ndcr & NDCR_PAGE_SZ ? 2048 : 512;
-	/* set info fields needed to read id */
-	info->read_id_bytes = (info->page_size == 2048) ? 4 : 2;
-	info->reg_ndcr = ndcr;
-	info->cmdset = &default_cmdset;
 
-	info->ndtr0cs0 = nand_readl(info, NDTR0CS0);
-	info->ndtr1cs0 = nand_readl(info, NDTR1CS0);
+	if (ndcr & NDCR_PAGE_SZ) {
+		host->page_size = 2048;
+		host->read_id_bytes = 4;
+	} else {
+		host->page_size = 512;
+		host->read_id_bytes = 2;
+	}
+
+	host->reg_ndcr = ndcr & ~NDCR_INT_MASK;
+	host->cmdset = &default_cmdset;
+
+	host->ndtr0cs0 = nand_readl(info, NDTR0CS0);
+	host->ndtr1cs0 = nand_readl(info, NDTR1CS0);
 
 	return 0;
 }
@@ -847,7 +898,6 @@ static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info)
 		return -ENOMEM;
 	}
 
-	info->data_buff_size = MAX_BUFF_SIZE;
 	info->data_desc = (void *)info->data_buff + data_desc_offset;
 	info->data_desc_addr = info->data_buff_phys + data_desc_offset;
 
@@ -855,7 +905,7 @@ static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info)
 				pxa3xx_nand_data_dma_irq, info);
 	if (info->data_dma_ch < 0) {
 		dev_err(&pdev->dev, "failed to request data dma\n");
-		dma_free_coherent(&pdev->dev, info->data_buff_size,
+		dma_free_coherent(&pdev->dev, MAX_BUFF_SIZE,
 				info->data_buff, info->data_buff_phys);
 		return info->data_dma_ch;
 	}
@@ -865,24 +915,28 @@ static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info)
 
 static int pxa3xx_nand_sensing(struct pxa3xx_nand_info *info)
 {
-	struct mtd_info *mtd = info->mtd;
-	struct nand_chip *chip = mtd->priv;
-
+	struct mtd_info *mtd;
+	int ret;
+	mtd = info->host[info->cs]->mtd;
 	/* use the common timing to make a try */
-	pxa3xx_nand_config_flash(info, &builtin_flash_types[0]);
-	chip->cmdfunc(mtd, NAND_CMD_RESET, 0, 0);
+	ret = pxa3xx_nand_config_flash(info, &builtin_flash_types[0]);
+	if (ret)
+		return ret;
+
+	pxa3xx_nand_cmdfunc(mtd, NAND_CMD_RESET, 0, 0);
 	if (info->is_ready)
-		return 1;
-	else
 		return 0;
+
+	return -ENODEV;
 }
 
 static int pxa3xx_nand_scan(struct mtd_info *mtd)
 {
-	struct pxa3xx_nand_info *info = mtd->priv;
+	struct pxa3xx_nand_host *host = mtd->priv;
+	struct pxa3xx_nand_info *info = host->info_data;
 	struct platform_device *pdev = info->pdev;
 	struct pxa3xx_nand_platform_data *pdata = pdev->dev.platform_data;
-	struct nand_flash_dev pxa3xx_flash_ids[2] = { {NULL,}, {NULL,} };
+	struct nand_flash_dev pxa3xx_flash_ids[2], *def = NULL;
 	const struct pxa3xx_nand_flash *f = NULL;
 	struct nand_chip *chip = mtd->priv;
 	uint32_t id = -1;
@@ -893,22 +947,20 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
 		goto KEEP_CONFIG;
 
 	ret = pxa3xx_nand_sensing(info);
-	if (!ret) {
-		kfree(mtd);
-		info->mtd = NULL;
-		printk(KERN_INFO "There is no nand chip on cs 0!\n");
+	if (ret) {
+		dev_info(&info->pdev->dev, "There is no chip on cs %d!\n",
+			 info->cs);
 
-		return -EINVAL;
+		return ret;
 	}
 
 	chip->cmdfunc(mtd, NAND_CMD_READID, 0, 0);
 	id = *((uint16_t *)(info->data_buff));
 	if (id != 0)
-		printk(KERN_INFO "Detect a flash id %x\n", id);
+		dev_info(&info->pdev->dev, "Detect a flash id %x\n", id);
 	else {
-		kfree(mtd);
-		info->mtd = NULL;
-		printk(KERN_WARNING "Read out ID 0, potential timing set wrong!!\n");
+		dev_warn(&info->pdev->dev,
+			 "Read out ID 0, potential timing set wrong!!\n");
 
 		return -EINVAL;
 	}
@@ -926,14 +978,17 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
 	}
 
 	if (i >= (ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1)) {
-		kfree(mtd);
-		info->mtd = NULL;
-		printk(KERN_ERR "ERROR!! flash not defined!!!\n");
+		dev_err(&info->pdev->dev, "ERROR!! flash not defined!!!\n");
 
 		return -EINVAL;
 	}
 
-	pxa3xx_nand_config_flash(info, f);
+	ret = pxa3xx_nand_config_flash(info, f);
+	if (ret) {
+		dev_err(&info->pdev->dev, "ERROR! Configure failed\n");
+		return ret;
+	}
+
 	pxa3xx_flash_ids[0].name = f->name;
 	pxa3xx_flash_ids[0].id = (f->chip_id >> 8) & 0xffff;
 	pxa3xx_flash_ids[0].pagesize = f->page_size;
@@ -942,62 +997,78 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
 	pxa3xx_flash_ids[0].erasesize = f->page_size * f->page_per_block;
 	if (f->flash_width == 16)
 		pxa3xx_flash_ids[0].options = NAND_BUSWIDTH_16;
+	pxa3xx_flash_ids[1].name = NULL;
+	def = pxa3xx_flash_ids;
 KEEP_CONFIG:
-	if (nand_scan_ident(mtd, 1, pxa3xx_flash_ids))
+	chip->ecc.mode = NAND_ECC_HW;
+	chip->ecc.size = host->page_size;
+
+	chip->options = NAND_NO_AUTOINCR;
+	chip->options |= NAND_NO_READRDY;
+	if (host->reg_ndcr & NDCR_DWIDTH_M)
+		chip->options |= NAND_BUSWIDTH_16;
+
+	if (nand_scan_ident(mtd, 1, def))
 		return -ENODEV;
 	/* calculate addressing information */
-	info->col_addr_cycles = (mtd->writesize >= 2048) ? 2 : 1;
+	if (mtd->writesize >= 2048)
+		host->col_addr_cycles = 2;
+	else
+		host->col_addr_cycles = 1;
+
 	info->oob_buff = info->data_buff + mtd->writesize;
 	if ((mtd->size >> chip->page_shift) > 65536)
-		info->row_addr_cycles = 3;
+		host->row_addr_cycles = 3;
 	else
-		info->row_addr_cycles = 2;
-	mtd->name = mtd_names[0];
-	chip->ecc.mode = NAND_ECC_HW;
-	chip->ecc.size = f->page_size;
-
-	chip->options = (f->flash_width == 16) ? NAND_BUSWIDTH_16 : 0;
-	chip->options |= NAND_NO_AUTOINCR;
-	chip->options |= NAND_NO_READRDY;
+		host->row_addr_cycles = 2;
 
+	mtd->name = mtd_names[0];
 	return nand_scan_tail(mtd);
 }
 
-static
-struct pxa3xx_nand_info *alloc_nand_resource(struct platform_device *pdev)
+static int alloc_nand_resource(struct platform_device *pdev)
 {
+	struct pxa3xx_nand_platform_data *pdata;
 	struct pxa3xx_nand_info *info;
+	struct pxa3xx_nand_host *host;
 	struct nand_chip *chip;
 	struct mtd_info *mtd;
 	struct resource *r;
-	int ret, irq;
+	int ret, irq, cs;
 
-	mtd = kzalloc(sizeof(struct mtd_info) + sizeof(struct pxa3xx_nand_info),
-			GFP_KERNEL);
-	if (!mtd) {
+	pdata = pdev->dev.platform_data;
+	info = kzalloc(sizeof(*info) + (sizeof(*mtd) +
+		       sizeof(*host)) * pdata->num_cs, GFP_KERNEL);
+	if (!info) {
 		dev_err(&pdev->dev, "failed to allocate memory\n");
-		return NULL;
+		return -ENOMEM;
 	}
 
-	info = (struct pxa3xx_nand_info *)(&mtd[1]);
-	chip = (struct nand_chip *)(&mtd[1]);
 	info->pdev = pdev;
-	info->mtd = mtd;
-	mtd->priv = info;
-	mtd->owner = THIS_MODULE;
-
-	chip->ecc.read_page	= pxa3xx_nand_read_page_hwecc;
-	chip->ecc.write_page	= pxa3xx_nand_write_page_hwecc;
-	chip->controller        = &info->controller;
-	chip->waitfunc		= pxa3xx_nand_waitfunc;
-	chip->select_chip	= pxa3xx_nand_select_chip;
-	chip->dev_ready		= pxa3xx_nand_dev_ready;
-	chip->cmdfunc		= pxa3xx_nand_cmdfunc;
-	chip->read_word		= pxa3xx_nand_read_word;
-	chip->read_byte		= pxa3xx_nand_read_byte;
-	chip->read_buf		= pxa3xx_nand_read_buf;
-	chip->write_buf		= pxa3xx_nand_write_buf;
-	chip->verify_buf	= pxa3xx_nand_verify_buf;
+	for (cs = 0; cs < pdata->num_cs; cs++) {
+		mtd = (struct mtd_info *)((unsigned int)&info[1] +
+		      (sizeof(*mtd) + sizeof(*host)) * cs);
+		chip = (struct nand_chip *)(&mtd[1]);
+		host = (struct pxa3xx_nand_host *)chip;
+		info->host[cs] = host;
+		host->mtd = mtd;
+		host->cs = cs;
+		host->info_data = info;
+		mtd->priv = host;
+		mtd->owner = THIS_MODULE;
+
+		chip->ecc.read_page	= pxa3xx_nand_read_page_hwecc;
+		chip->ecc.write_page	= pxa3xx_nand_write_page_hwecc;
+		chip->controller        = &info->controller;
+		chip->waitfunc		= pxa3xx_nand_waitfunc;
+		chip->select_chip	= pxa3xx_nand_select_chip;
+		chip->cmdfunc		= pxa3xx_nand_cmdfunc;
+		chip->read_word		= pxa3xx_nand_read_word;
+		chip->read_byte		= pxa3xx_nand_read_byte;
+		chip->read_buf		= pxa3xx_nand_read_buf;
+		chip->write_buf		= pxa3xx_nand_write_buf;
+		chip->verify_buf	= pxa3xx_nand_verify_buf;
+	}
 
 	spin_lock_init(&chip->controller->lock);
 	init_waitqueue_head(&chip->controller->wq);
@@ -1070,13 +1141,13 @@ struct pxa3xx_nand_info *alloc_nand_resource(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, info);
 
-	return info;
+	return 0;
 
 fail_free_buf:
 	free_irq(irq, info);
 	if (use_dma) {
 		pxa_free_dma(info->data_dma_ch);
-		dma_free_coherent(&pdev->dev, info->data_buff_size,
+		dma_free_coherent(&pdev->dev, MAX_BUFF_SIZE,
 			info->data_buff, info->data_buff_phys);
 	} else
 		kfree(info->data_buff);
@@ -1088,17 +1159,21 @@ fail_put_clk:
 	clk_disable(info->clk);
 	clk_put(info->clk);
 fail_free_mtd:
-	kfree(mtd);
-	return NULL;
+	kfree(info);
+	return ret;
 }
 
 static int pxa3xx_nand_remove(struct platform_device *pdev)
 {
 	struct pxa3xx_nand_info *info = platform_get_drvdata(pdev);
-	struct mtd_info *mtd = info->mtd;
+	struct pxa3xx_nand_platform_data *pdata;
 	struct resource *r;
-	int irq;
+	int irq, cs;
 
+	if (!info)
+		return 0;
+
+	pdata = pdev->dev.platform_data;
 	platform_set_drvdata(pdev, NULL);
 
 	irq = platform_get_irq(pdev, 0);
@@ -1106,7 +1181,7 @@ static int pxa3xx_nand_remove(struct platform_device *pdev)
 		free_irq(irq, info);
 	if (use_dma) {
 		pxa_free_dma(info->data_dma_ch);
-		dma_free_writecombine(&pdev->dev, info->data_buff_size,
+		dma_free_writecombine(&pdev->dev, MAX_BUFF_SIZE,
 				info->data_buff, info->data_buff_phys);
 	} else
 		kfree(info->data_buff);
@@ -1118,10 +1193,9 @@ static int pxa3xx_nand_remove(struct platform_device *pdev)
 	clk_disable(info->clk);
 	clk_put(info->clk);
 
-	if (mtd) {
-		mtd_device_unregister(mtd);
-		kfree(mtd);
-	}
+	for (cs = 0; cs < pdata->num_cs; cs++)
+		nand_release(info->host[cs]->mtd);
+	kfree(info);
 	return 0;
 }
 
@@ -1129,6 +1203,7 @@ static int pxa3xx_nand_probe(struct platform_device *pdev)
 {
 	struct pxa3xx_nand_platform_data *pdata;
 	struct pxa3xx_nand_info *info;
+	int ret, cs, probe_success;
 
 	pdata = pdev->dev.platform_data;
 	if (!pdata) {
@@ -1136,52 +1211,88 @@ static int pxa3xx_nand_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
-	info = alloc_nand_resource(pdev);
-	if (info == NULL)
-		return -ENOMEM;
-
-	if (pxa3xx_nand_scan(info->mtd)) {
-		dev_err(&pdev->dev, "failed to scan nand\n");
-		pxa3xx_nand_remove(pdev);
-		return -ENODEV;
+	ret = alloc_nand_resource(pdev);
+	if (ret) {
+		dev_err(&pdev->dev, "alloc nand resource failed\n");
+		return ret;
 	}
 
-	if (mtd_has_cmdlinepart()) {
-		const char *probes[] = { "cmdlinepart", NULL };
-		struct mtd_partition *parts;
-		int nr_parts;
+	info = platform_get_drvdata(pdev);
+	probe_success = 0;
+	for (cs = 0; cs < pdata->num_cs; cs++) {
+		info->cs = cs;
+		ret = pxa3xx_nand_scan(info->host[cs]->mtd);
+		if (ret) {
+			dev_warn(&pdev->dev, "failed to scan nand at cs %d\n",
+				cs);
+			continue;
+		}
 
-		nr_parts = parse_mtd_partitions(info->mtd, probes, &parts, 0);
+		ret = mtd_device_parse_register(info->host[cs]->mtd, NULL, 0,
+				pdata->parts[cs], pdata->nr_parts[cs]);
+		if (!ret)
+			probe_success = 1;
+	}
 
-		if (nr_parts)
-			return mtd_device_register(info->mtd, parts, nr_parts);
+	if (!probe_success) {
+		pxa3xx_nand_remove(pdev);
+		return -ENODEV;
 	}
 
-	return mtd_device_register(info->mtd, pdata->parts, pdata->nr_parts);
+	return 0;
 }
 
 #ifdef CONFIG_PM
 static int pxa3xx_nand_suspend(struct platform_device *pdev, pm_message_t state)
 {
 	struct pxa3xx_nand_info *info = platform_get_drvdata(pdev);
-	struct mtd_info *mtd = info->mtd;
+	struct pxa3xx_nand_platform_data *pdata;
+	struct mtd_info *mtd;
+	int cs;
 
+	pdata = pdev->dev.platform_data;
 	if (info->state) {
 		dev_err(&pdev->dev, "driver busy, state = %d\n", info->state);
 		return -EAGAIN;
 	}
 
+	for (cs = 0; cs < pdata->num_cs; cs++) {
+		mtd = info->host[cs]->mtd;
+		mtd->suspend(mtd);
+	}
+
 	return 0;
 }
 
 static int pxa3xx_nand_resume(struct platform_device *pdev)
 {
 	struct pxa3xx_nand_info *info = platform_get_drvdata(pdev);
-	struct mtd_info *mtd = info->mtd;
+	struct pxa3xx_nand_platform_data *pdata;
+	struct mtd_info *mtd;
+	int cs;
 
-	nand_writel(info, NDTR0CS0, info->ndtr0cs0);
-	nand_writel(info, NDTR1CS0, info->ndtr1cs0);
-	clk_enable(info->clk);
+	pdata = pdev->dev.platform_data;
+	/* We don't want to handle interrupt without calling mtd routine */
+	disable_int(info, NDCR_INT_MASK);
+
+	/*
+	 * Directly set the chip select to a invalid value,
+	 * then the driver would reset the timing according
+	 * to current chip select at the beginning of cmdfunc
+	 */
+	info->cs = 0xff;
+
+	/*
+	 * As the spec says, the NDSR would be updated to 0x1800 when
+	 * doing the nand_clk disable/enable.
+	 * To prevent it damaging state machine of the driver, clear
+	 * all status before resume
+	 */
+	nand_writel(info, NDSR, NDSR_MASK);
+	for (cs = 0; cs < pdata->num_cs; cs++) {
+		mtd = info->host[cs]->mtd;
+		mtd->resume(mtd);
+	}
 
 	return 0;
 }
diff --git a/drivers/mtd/nand/r852.c b/drivers/mtd/nand/r852.c
index cae2e013c986..f20f393bfda6 100644
--- a/drivers/mtd/nand/r852.c
+++ b/drivers/mtd/nand/r852.c
@@ -1027,7 +1027,7 @@ void r852_shutdown(struct pci_dev *pci_dev)
 }
 
 #ifdef CONFIG_PM
-int r852_suspend(struct device *device)
+static int r852_suspend(struct device *device)
 {
 	struct r852_device *dev = pci_get_drvdata(to_pci_dev(device));
 
@@ -1048,7 +1048,7 @@ int r852_suspend(struct device *device)
 	return 0;
 }
 
-int r852_resume(struct device *device)
+static int r852_resume(struct device *device)
 {
 	struct r852_device *dev = pci_get_drvdata(to_pci_dev(device));
 
@@ -1092,7 +1092,7 @@ static const struct pci_device_id r852_pci_id_tbl[] = {
 
 MODULE_DEVICE_TABLE(pci, r852_pci_id_tbl);
 
-SIMPLE_DEV_PM_OPS(r852_pm_ops, r852_suspend, r852_resume);
+static SIMPLE_DEV_PM_OPS(r852_pm_ops, r852_suspend, r852_resume);
 
 static struct pci_driver r852_pci_driver = {
 	.name		= DRV_NAME,
diff --git a/drivers/mtd/nand/rtc_from4.c b/drivers/mtd/nand/rtc_from4.c
index c9f9127ff770..f309addc2fa0 100644
--- a/drivers/mtd/nand/rtc_from4.c
+++ b/drivers/mtd/nand/rtc_from4.c
@@ -351,7 +351,7 @@ static int rtc_from4_correct_data(struct mtd_info *mtd, const u_char *buf, u_cha
 		return 0;
 	}
 
-	/* Read the syndrom pattern from the FPGA and correct the bitorder */
+	/* Read the syndrome pattern from the FPGA and correct the bitorder */
 	rs_ecc = (volatile unsigned short *)(rtc_from4_fio_base + RTC_FROM4_RS_ECC);
 	for (i = 0; i < 8; i++) {
 		ecc[i] = bitrev8(*rs_ecc);
@@ -380,7 +380,7 @@ static int rtc_from4_correct_data(struct mtd_info *mtd, const u_char *buf, u_cha
 	/* Let the library code do its magic. */
 	res = decode_rs8(rs_decoder, (uint8_t *) buf, par, 512, syn, 0, NULL, 0xff, NULL);
 	if (res > 0) {
-		DEBUG(MTD_DEBUG_LEVEL0, "rtc_from4_correct_data: " "ECC corrected %d errors on read\n", res);
+		pr_debug("rtc_from4_correct_data: " "ECC corrected %d errors on read\n", res);
 	}
 	return res;
 }
@@ -444,7 +444,6 @@ static int rtc_from4_errstat(struct mtd_info *mtd, struct nand_chip *this,
 		len = mtd->writesize;
 		buf = kmalloc(len, GFP_KERNEL);
 		if (!buf) {
-			printk(KERN_ERR "rtc_from4_errstat: Out of memory!\n");
 			er_stat = 1;
 			goto out;
 		}
diff --git a/drivers/mtd/nand/s3c2410.c b/drivers/mtd/nand/s3c2410.c
index 4405468f196b..868685db6712 100644
--- a/drivers/mtd/nand/s3c2410.c
+++ b/drivers/mtd/nand/s3c2410.c
@@ -723,7 +723,7 @@ static int s3c24xx_nand_remove(struct platform_device *pdev)
 
 	/* free the common resources */
 
-	if (info->clk != NULL && !IS_ERR(info->clk)) {
+	if (!IS_ERR(info->clk)) {
 		s3c2410_nand_clk_set_state(info, CLOCK_DISABLE);
 		clk_put(info->clk);
 	}
@@ -744,26 +744,15 @@ static int s3c24xx_nand_remove(struct platform_device *pdev)
 	return 0;
 }
 
-const char *part_probes[] = { "cmdlinepart", NULL };
 static int s3c2410_nand_add_partition(struct s3c2410_nand_info *info,
 				      struct s3c2410_nand_mtd *mtd,
 				      struct s3c2410_nand_set *set)
 {
-	struct mtd_partition *part_info;
-	int nr_part = 0;
+	if (set)
+		mtd->mtd.name = set->name;
 
-	if (set == NULL)
-		return mtd_device_register(&mtd->mtd, NULL, 0);
-
-	mtd->mtd.name = set->name;
-	nr_part = parse_mtd_partitions(&mtd->mtd, part_probes, &part_info, 0);
-
-	if (nr_part <= 0 && set->nr_partitions > 0) {
-		nr_part = set->nr_partitions;
-		part_info = set->partitions;
-	}
-
-	return mtd_device_register(&mtd->mtd, part_info, nr_part);
+	return mtd_device_parse_register(&mtd->mtd, NULL, 0,
+			set->partitions, set->nr_partitions);
 }
 
 /**
@@ -880,8 +869,10 @@ static void s3c2410_nand_init_chip(struct s3c2410_nand_info *info,
 	/* If you use u-boot BBT creation code, specifying this flag will
 	 * let the kernel fish out the BBT from the NAND, and also skip the
 	 * full NAND scan that can take 1/2s or so. Little things... */
-	if (set->flash_bbt)
-		chip->options |= NAND_USE_FLASH_BBT | NAND_SKIP_BBTSCAN;
+	if (set->flash_bbt) {
+		chip->bbt_options |= NAND_BBT_USE_FLASH;
+		chip->options |= NAND_SKIP_BBTSCAN;
+	}
 }
 
 /**
diff --git a/drivers/mtd/nand/sharpsl.c b/drivers/mtd/nand/sharpsl.c
index 19e24ed089ea..619d2a504788 100644
--- a/drivers/mtd/nand/sharpsl.c
+++ b/drivers/mtd/nand/sharpsl.c
@@ -103,16 +103,12 @@ static int sharpsl_nand_calculate_ecc(struct mtd_info *mtd, const u_char * dat,
 	return readb(sharpsl->io + ECCCNTR) != 0;
 }
 
-static const char *part_probes[] = { "cmdlinepart", NULL };
-
 /*
  * Main initialization routine
  */
 static int __devinit sharpsl_nand_probe(struct platform_device *pdev)
 {
 	struct nand_chip *this;
-	struct mtd_partition *sharpsl_partition_info;
-	int nr_partitions;
 	struct resource *r;
 	int err = 0;
 	struct sharpsl_nand *sharpsl;
@@ -184,14 +180,9 @@ static int __devinit sharpsl_nand_probe(struct platform_device *pdev)
 
 	/* Register the partitions */
 	sharpsl->mtd.name = "sharpsl-nand";
-	nr_partitions = parse_mtd_partitions(&sharpsl->mtd, part_probes, &sharpsl_partition_info, 0);
-	if (nr_partitions <= 0) {
-		nr_partitions = data->nr_partitions;
-		sharpsl_partition_info = data->partitions;
-	}
 
-	err = mtd_device_register(&sharpsl->mtd, sharpsl_partition_info,
-				  nr_partitions);
+	err = mtd_device_parse_register(&sharpsl->mtd, NULL, 0,
+			data->partitions, data->nr_partitions);
 	if (err)
 		goto err_add;
 
diff --git a/drivers/mtd/nand/sm_common.c b/drivers/mtd/nand/sm_common.c
index 43469715b3fa..32ae5af7444f 100644
--- a/drivers/mtd/nand/sm_common.c
+++ b/drivers/mtd/nand/sm_common.c
@@ -48,7 +48,7 @@ static int sm_block_markbad(struct mtd_info *mtd, loff_t ofs)
 
 	/* As long as this function is called on erase block boundaries
 		it will work correctly for 256 byte nand */
-	ops.mode = MTD_OOB_PLACE;
+	ops.mode = MTD_OPS_PLACE_OOB;
 	ops.ooboffs = 0;
 	ops.ooblen = mtd->oobsize;
 	ops.oobbuf = (void *)&oob;
diff --git a/drivers/mtd/nand/socrates_nand.c b/drivers/mtd/nand/socrates_nand.c
index ca2d0555729e..0fb24f9c2327 100644
--- a/drivers/mtd/nand/socrates_nand.c
+++ b/drivers/mtd/nand/socrates_nand.c
@@ -155,8 +155,6 @@ static int socrates_nand_device_ready(struct mtd_info *mtd)
 	return 1;
 }
 
-static const char *part_probes[] = { "cmdlinepart", NULL };
-
 /*
  * Probe for the NAND device.
  */
@@ -166,8 +164,7 @@ static int __devinit socrates_nand_probe(struct platform_device *ofdev)
 	struct mtd_info *mtd;
 	struct nand_chip *nand_chip;
 	int res;
-	struct mtd_partition *partitions = NULL;
-	int num_partitions = 0;
+	struct mtd_part_parser_data ppdata;
 
 	/* Allocate memory for the device structure (and zero it) */
 	host = kzalloc(sizeof(struct socrates_nand_host), GFP_KERNEL);
@@ -193,6 +190,7 @@ static int __devinit socrates_nand_probe(struct platform_device *ofdev)
 	mtd->name = "socrates_nand";
 	mtd->owner = THIS_MODULE;
 	mtd->dev.parent = &ofdev->dev;
+	ppdata.of_node = ofdev->dev.of_node;
 
 	/*should never be accessed directly */
 	nand_chip->IO_ADDR_R = (void *)0xdeadbeef;
@@ -225,30 +223,10 @@ static int __devinit socrates_nand_probe(struct platform_device *ofdev)
 		goto out;
 	}
 
-#ifdef CONFIG_MTD_CMDLINE_PARTS
-	num_partitions = parse_mtd_partitions(mtd, part_probes,
-					      &partitions, 0);
-	if (num_partitions < 0) {
-		res = num_partitions;
-		goto release;
-	}
-#endif
-
-	if (num_partitions == 0) {
-		num_partitions = of_mtd_parse_partitions(&ofdev->dev,
-							 ofdev->dev.of_node,
-							 &partitions);
-		if (num_partitions < 0) {
-			res = num_partitions;
-			goto release;
-		}
-	}
-
-	res = mtd_device_register(mtd, partitions, num_partitions);
+	res = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0);
 	if (!res)
 		return res;
 
-release:
 	nand_release(mtd);
 
 out:
diff --git a/drivers/mtd/nand/tmio_nand.c b/drivers/mtd/nand/tmio_nand.c
index 11e8371b5683..beebd95f7690 100644
--- a/drivers/mtd/nand/tmio_nand.c
+++ b/drivers/mtd/nand/tmio_nand.c
@@ -121,9 +121,6 @@ struct tmio_nand {
 
 #define mtd_to_tmio(m)			container_of(m, struct tmio_nand, mtd)
 
-#ifdef CONFIG_MTD_CMDLINE_PARTS
-static const char *part_probes[] = { "cmdlinepart", NULL };
-#endif
 
 /*--------------------------------------------------------------------------*/
 
@@ -381,8 +378,6 @@ static int tmio_probe(struct platform_device *dev)
 	struct tmio_nand *tmio;
 	struct mtd_info *mtd;
 	struct nand_chip *nand_chip;
-	struct mtd_partition *parts;
-	int nbparts = 0;
 	int retval;
 
 	if (data == NULL)
@@ -461,15 +456,9 @@ static int tmio_probe(struct platform_device *dev)
 		goto err_scan;
 	}
 	/* Register the partitions */
-#ifdef CONFIG_MTD_CMDLINE_PARTS
-	nbparts = parse_mtd_partitions(mtd, part_probes, &parts, 0);
-#endif
-	if (nbparts <= 0 && data) {
-		parts = data->partition;
-		nbparts = data->num_partitions;
-	}
-
-	retval = mtd_device_register(mtd, parts, nbparts);
+	retval = mtd_device_parse_register(mtd, NULL, 0,
+			data ? data->partition : NULL,
+			data ? data->num_partitions : 0);
 	if (!retval)
 		return retval;
 
diff --git a/drivers/mtd/nand/txx9ndfmc.c b/drivers/mtd/nand/txx9ndfmc.c
index bfba4e39a6c5..ace46fdaef58 100644
--- a/drivers/mtd/nand/txx9ndfmc.c
+++ b/drivers/mtd/nand/txx9ndfmc.c
@@ -74,7 +74,6 @@ struct txx9ndfmc_drvdata {
 	unsigned char hold;	/* in gbusclock */
 	unsigned char spw;	/* in gbusclock */
 	struct nand_hw_control hw_control;
-	struct mtd_partition *parts[MAX_TXX9NDFMC_DEV];
 };
 
 static struct platform_device *mtd_to_platdev(struct mtd_info *mtd)
@@ -287,7 +286,6 @@ static int txx9ndfmc_nand_scan(struct mtd_info *mtd)
 static int __init txx9ndfmc_probe(struct platform_device *dev)
 {
 	struct txx9ndfmc_platform_data *plat = dev->dev.platform_data;
-	static const char *probes[] = { "cmdlinepart", NULL };
 	int hold, spw;
 	int i;
 	struct txx9ndfmc_drvdata *drvdata;
@@ -333,7 +331,6 @@ static int __init txx9ndfmc_probe(struct platform_device *dev)
 		struct txx9ndfmc_priv *txx9_priv;
 		struct nand_chip *chip;
 		struct mtd_info *mtd;
-		int nr_parts;
 
 		if (!(plat->ch_mask & (1 << i)))
 			continue;
@@ -393,9 +390,7 @@ static int __init txx9ndfmc_probe(struct platform_device *dev)
 		}
 		mtd->name = txx9_priv->mtdname;
 
-		nr_parts = parse_mtd_partitions(mtd, probes,
-						&drvdata->parts[i], 0);
-		mtd_device_register(mtd, drvdata->parts[i], nr_parts);
+		mtd_device_parse_register(mtd, NULL, 0, NULL, 0);
 		drvdata->mtds[i] = mtd;
 	}
 
@@ -421,7 +416,6 @@ static int __exit txx9ndfmc_remove(struct platform_device *dev)
 		txx9_priv = chip->priv;
 
 		nand_release(mtd);
-		kfree(drvdata->parts[i]);
 		kfree(txx9_priv->mtdname);
 		kfree(txx9_priv);
 	}