diff options
| author | Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> | 2020-03-10 14:17:07 +0100 |
|---|---|---|
| committer | Mauro Carvalho Chehab <mchehab+huawei@kernel.org> | 2020-03-12 17:18:13 +0100 |
| commit | ca45448a56659c6df6e0436188e97f6cc65dea8a (patch) | |
| tree | 6c5e1f6cc37f9baaa4107edf6bc2fb9d16193aa2 /drivers/media | |
| parent | da84967943f7bacd073606a05641d6b0bc1216bd (diff) | |
| download | linux-ca45448a56659c6df6e0436188e97f6cc65dea8a.tar.bz2 | |
media: i2c: imx219: Fix power sequence
When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
state.
The powerup sequence in the datasheet[1] shows the sensor entering into
LP-11 in streaming mode, so to fix this issue transitions are performed
from "streaming -> standby" in the probe() after power up.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
[1] https://publiclab.org/system/images/photos/000/023/294/original/
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Diffstat (limited to 'drivers/media')
| -rw-r--r-- | drivers/media/i2c/imx219.c | 17 |
1 files changed, 17 insertions, 0 deletions
diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c index f1effb5a5f66..16010ca1781a 100644 --- a/drivers/media/i2c/imx219.c +++ b/drivers/media/i2c/imx219.c @@ -1224,6 +1224,23 @@ static int imx219_probe(struct i2c_client *client) /* Set default mode to max resolution */ imx219->mode = &supported_modes[0]; + /* sensor doesn't enter LP-11 state upon power up until and unless + * streaming is started, so upon power up switch the modes to: + * streaming -> standby + */ + ret = imx219_write_reg(imx219, IMX219_REG_MODE_SELECT, + IMX219_REG_VALUE_08BIT, IMX219_MODE_STREAMING); + if (ret < 0) + goto error_power_off; + usleep_range(100, 110); + + /* put sensor back to standby mode */ + ret = imx219_write_reg(imx219, IMX219_REG_MODE_SELECT, + IMX219_REG_VALUE_08BIT, IMX219_MODE_STANDBY); + if (ret < 0) + goto error_power_off; + usleep_range(100, 110); + ret = imx219_init_controls(imx219); if (ret) goto error_power_off; |