Merge tag 'iio-for-4.7b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing

Jonathan writes:

2nd set of new device support, features and cleanup for IIO in the 4.7 cycle.

Bit of a bumper set for new drivers but plenty of other stuff here as well!

New device support
* ad5592R ADC/DAC
  - new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
  - new driver with triggered buffer support in follow up patch.
* bmi160 imu
  - new driver
* bmp280
  - bmp180 support - note there is support in the misc/bmp085 driver. Intent
    is to remove that driver long term.
* invensense mpu6050
  - cleanup leading to explicit support of mpu9150 with a good few cleanups
    along the way.
* Hope RF hp03 pressure and temperature sensor.
  - new driver
* maxim DS1803 potentiometer
  - new driver
* maxim max44000 light and proximity sensor
  - new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
  - new driver. There is an existing driver in misc that this is pretty much
    intended to replace.  The discussion on whether to support the non standard
    interface of that driver is some way is continuing.
* st-gyro
  - lsm9ds0-gyro.  The accel/magn side of this will take a while longer as
    extensions to the st library are needed for cases where two types of sensor
    share a single i2c address.
* ti-adc081c
  - support the adc101c and adc121c
* Vishay VEML6070 UV sensor
  - new driver.

New features
* core
  - devm_ APIs for channel_get and channel_get_all.  The first user of these
    is the generic ADC based thermal driver.  As it is going through the
    thermal tree these will be picked up as a patch to that next cycle as that
    is how the author preferred to do it.
  - mounting matrix support.  This new core support allows devices to provide
    to userspace (typically from the device tree) allowing compensation for how
    the sensor is mounted on the device.  First examples are on UAVs but it
    has a more mundane use on typical phone where the chip may be on the front
    or the back of the circuit board and soldered at any angle. Includes
    support for this ABI in ak8975 (which has an older interface, now
    deprecated) and mpu6050.
* tools
  - add a -a option to enable all available channels in generic_buffer sample.
    Makes it somewhat easier to use.
* adis library and drivers
  - support manual self test flag clearing.  This has technically been broken
    for a very long time - result is an offset on readings as the applied field
    is on all the time.
* ak8975
  - triggered buffer support
* bmc150
  - spi support (including splitting the driver into core and i2c parts)
* bmp280
  - oversampling support.
* dht11
  - improved logging - useful to debug timing issues on this quirky device.
* st-sensors
  - read each channel invidivually as not all support the optimization of
  reading in bulk.  This is technically a fix, but will need to be backported
  if desired.
  - support open drain and shared interrupts.
* ti-adc081c
  - triggered buffer support.

Cleanups
* inkern
  - white space fix.
* ad7606
  - use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
  - white space fix.
* ad9523
  - unsigned -> unsigned int
* apds9660
  - brace location tidying up.
  - silence an uninitialized variable warning.
* ak8975
  - else and brace on same line fix.
* at91_adc
  - white space fixes.
* bmc150
  - use regmap stored copy of the device pointer rather than having an
    additional copy.
* bmg160
  - use regmap stored copy of the device pointer rather than having an
    additional copy.
* hid-sensors
  - white space fixes.
* mcp3422
  - white space fix.
* mma7455
  - use regmap to retrieve the device struct rather than carrying another copy
    in the private data.
* ms_sensors
  - white space fix.
* mxs-lradc
  - move current bindings out of staging - some will be shortly deprecated but
    the reality is that we have device trees out there using them so they will
    need to be supported for some time.  They accidentally got left behind
    when the driver graduated from staging.
  - white space cleanup.
  - set INPUT_PROP_DIRECT.
  - move ts config into a better function.
  - move the STMP reset out of the ADC init.
* vf610_adc
  - case label indenting fix.

7 files changed, 146 insertions, 55 deletions

diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 5937030f0444..25378c5882e2 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -385,11 +385,11 @@ config ROCKCHIP_SARADC
 	  module will be called rockchip_saradc.
 
 config TI_ADC081C
-	tristate "Texas Instruments ADC081C021/027"
+	tristate "Texas Instruments ADC081C/ADC101C/ADC121C family"
 	depends on I2C
 	help
-	  If you say yes here you get support for Texas Instruments ADC081C021
-	  and ADC081C027 ADC chips.
+	  If you say yes here you get support for Texas Instruments ADC081C,
+	  ADC101C and ADC121C ADC chips.
 
 	  This driver can also be built as a module. If so, the module will be
 	  called ti-adc081c.
diff --git a/drivers/iio/adc/ad799x.c b/drivers/iio/adc/ad799x.c
index 01d71588d752..a3f5254f4e51 100644
--- a/drivers/iio/adc/ad799x.c
+++ b/drivers/iio/adc/ad799x.c
@@ -477,7 +477,7 @@ static int ad799x_read_event_value(struct iio_dev *indio_dev,
 	if (ret < 0)
 		return ret;
 	*val = (ret >> chan->scan_type.shift) &
-		GENMASK(chan->scan_type.realbits - 1 , 0);
+		GENMASK(chan->scan_type.realbits - 1, 0);
 
 	return IIO_VAL_INT;
 }
diff --git a/drivers/iio/adc/at91_adc.c b/drivers/iio/adc/at91_adc.c
index f284cd6a93d6..52430ba171f3 100644
--- a/drivers/iio/adc/at91_adc.c
+++ b/drivers/iio/adc/at91_adc.c
@@ -797,8 +797,8 @@ static u32 calc_startup_ticks_9x5(u32 startup_time, u32 adc_clk_khz)
 	 * Startup Time = <lookup_table_value> / ADC Clock
 	 */
 	const int startup_lookup[] = {
-		0  , 8  , 16 , 24 ,
-		64 , 80 , 96 , 112,
+		0,   8,   16,  24,
+		64,  80,  96,  112,
 		512, 576, 640, 704,
 		768, 832, 896, 960
 		};
@@ -924,14 +924,14 @@ static int at91_adc_probe_dt(struct at91_adc_state *st,
 			ret = -EINVAL;
 			goto error_ret;
 		}
-	        trig->name = name;
+		trig->name = name;
 
 		if (of_property_read_u32(trig_node, "trigger-value", &prop)) {
 			dev_err(&idev->dev, "Missing trigger-value property in the DT.\n");
 			ret = -EINVAL;
 			goto error_ret;
 		}
-	        trig->value = prop;
+		trig->value = prop;
 		trig->is_external = of_property_read_bool(trig_node, "trigger-external");
 		i++;
 	}
diff --git a/drivers/iio/adc/mcp3422.c b/drivers/iio/adc/mcp3422.c
index d7b36efd2f3c..d1172dc1e8e2 100644
--- a/drivers/iio/adc/mcp3422.c
+++ b/drivers/iio/adc/mcp3422.c
@@ -61,9 +61,9 @@
 
 static const int mcp3422_scales[4][4] = {
 	{ 1000000, 500000, 250000, 125000 },
-	{ 250000 , 125000, 62500 , 31250  },
-	{ 62500  , 31250 , 15625 , 7812   },
-	{ 15625  , 7812  , 3906  , 1953   } };
+	{ 250000,  125000, 62500,  31250  },
+	{ 62500,   31250,  15625,  7812   },
+	{ 15625,   7812,   3906,   1953   } };
 
 /* Constant msleep times for data acquisitions */
 static const int mcp3422_read_times[4] = {
diff --git a/drivers/iio/adc/mxs-lradc.c b/drivers/iio/adc/mxs-lradc.c
index 33051b87aac2..ad26da1edbee 100644
--- a/drivers/iio/adc/mxs-lradc.c
+++ b/drivers/iio/adc/mxs-lradc.c
@@ -686,6 +686,17 @@ static void mxs_lradc_prepare_pressure(struct mxs_lradc *lradc)
 
 static void mxs_lradc_enable_touch_detection(struct mxs_lradc *lradc)
 {
+	/* Configure the touchscreen type */
+	if (lradc->soc == IMX28_LRADC) {
+		mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+				    LRADC_CTRL0);
+
+		if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE)
+			mxs_lradc_reg_set(lradc,
+					  LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+					  LRADC_CTRL0);
+	}
+
 	mxs_lradc_setup_touch_detection(lradc);
 
 	lradc->cur_plate = LRADC_TOUCH;
@@ -1127,6 +1138,7 @@ static int mxs_lradc_ts_register(struct mxs_lradc *lradc)
 	__set_bit(EV_ABS, input->evbit);
 	__set_bit(EV_KEY, input->evbit);
 	__set_bit(BTN_TOUCH, input->keybit);
+	__set_bit(INPUT_PROP_DIRECT, input->propbit);
 	input_set_abs_params(input, ABS_X, 0, LRADC_SINGLE_SAMPLE_MASK, 0, 0);
 	input_set_abs_params(input, ABS_Y, 0, LRADC_SINGLE_SAMPLE_MASK, 0, 0);
 	input_set_abs_params(input, ABS_PRESSURE, 0, LRADC_SINGLE_SAMPLE_MASK,
@@ -1475,18 +1487,13 @@ static const struct iio_chan_spec mx28_lradc_chan_spec[] = {
 	MXS_ADC_CHAN(15, IIO_VOLTAGE, "VDD5V"),
 };
 
-static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
+static void mxs_lradc_hw_init(struct mxs_lradc *lradc)
 {
 	/* The ADC always uses DELAY CHANNEL 0. */
 	const u32 adc_cfg =
 		(1 << (LRADC_DELAY_TRIGGER_DELAYS_OFFSET + 0)) |
 		(LRADC_DELAY_TIMER_PER << LRADC_DELAY_DELAY_OFFSET);
 
-	int ret = stmp_reset_block(lradc->base);
-
-	if (ret)
-		return ret;
-
 	/* Configure DELAY CHANNEL 0 for generic ADC sampling. */
 	mxs_lradc_reg_wrt(lradc, adc_cfg, LRADC_DELAY(0));
 
@@ -1495,20 +1502,8 @@ static int mxs_lradc_hw_init(struct mxs_lradc *lradc)
 	mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(2));
 	mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(3));
 
-	/* Configure the touchscreen type */
-	if (lradc->soc == IMX28_LRADC) {
-		mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
-				    LRADC_CTRL0);
-
-	if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE)
-		mxs_lradc_reg_set(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
-				  LRADC_CTRL0);
-	}
-
 	/* Start internal temperature sensing. */
 	mxs_lradc_reg_wrt(lradc, 0, LRADC_CTRL2);
-
-	return 0;
 }
 
 static void mxs_lradc_hw_stop(struct mxs_lradc *lradc)
@@ -1708,11 +1703,13 @@ static int mxs_lradc_probe(struct platform_device *pdev)
 		}
 	}
 
-	/* Configure the hardware. */
-	ret = mxs_lradc_hw_init(lradc);
+	ret = stmp_reset_block(lradc->base);
 	if (ret)
 		goto err_dev;
 
+	/* Configure the hardware. */
+	mxs_lradc_hw_init(lradc);
+
 	/* Register the touchscreen input device. */
 	if (touch_ret == 0) {
 		ret = mxs_lradc_ts_register(lradc);
diff --git a/drivers/iio/adc/ti-adc081c.c b/drivers/iio/adc/ti-adc081c.c
index ecbc12138d58..9fd032d9f402 100644
--- a/drivers/iio/adc/ti-adc081c.c
+++ b/drivers/iio/adc/ti-adc081c.c
@@ -1,9 +1,21 @@
 /*
+ * TI ADC081C/ADC101C/ADC121C 8/10/12-bit ADC driver
+ *
  * Copyright (C) 2012 Avionic Design GmbH
+ * Copyright (C) 2016 Intel
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
+ *
+ * Datasheets:
+ *	http://www.ti.com/lit/ds/symlink/adc081c021.pdf
+ *	http://www.ti.com/lit/ds/symlink/adc101c021.pdf
+ *	http://www.ti.com/lit/ds/symlink/adc121c021.pdf
+ *
+ * The devices have a very similar interface and differ mostly in the number of
+ * bits handled. For the 8-bit and 10-bit models the least-significant 4 or 2
+ * bits of value registers are reserved.
  */
 
 #include <linux/err.h>
@@ -12,11 +24,17 @@
 #include <linux/of.h>
 
 #include <linux/iio/iio.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
 #include <linux/regulator/consumer.h>
 
 struct adc081c {
 	struct i2c_client *i2c;
 	struct regulator *ref;
+
+	/* 8, 10 or 12 */
+	int bits;
 };
 
 #define REG_CONV_RES 0x00
@@ -34,7 +52,7 @@ static int adc081c_read_raw(struct iio_dev *iio,
 		if (err < 0)
 			return err;
 
-		*value = (err >> 4) & 0xff;
+		*value = (err & 0xFFF) >> (12 - adc->bits);
 		return IIO_VAL_INT;
 
 	case IIO_CHAN_INFO_SCALE:
@@ -43,7 +61,7 @@ static int adc081c_read_raw(struct iio_dev *iio,
 			return err;
 
 		*value = err / 1000;
-		*shift = 8;
+		*shift = adc->bits;
 
 		return IIO_VAL_FRACTIONAL_LOG2;
 
@@ -54,10 +72,53 @@ static int adc081c_read_raw(struct iio_dev *iio,
 	return -EINVAL;
 }
 
-static const struct iio_chan_spec adc081c_channel = {
-	.type = IIO_VOLTAGE,
-	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),
-	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+#define ADCxx1C_CHAN(_bits) {					\
+	.type = IIO_VOLTAGE,					\
+	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),	\
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
+	.scan_type = {						\
+		.sign = 'u',					\
+		.realbits = (_bits),				\
+		.storagebits = 16,				\
+		.shift = 12 - (_bits),				\
+		.endianness = IIO_CPU,				\
+	},							\
+}
+
+#define DEFINE_ADCxx1C_CHANNELS(_name, _bits)				\
+	static const struct iio_chan_spec _name ## _channels[] = {	\
+		ADCxx1C_CHAN((_bits)),					\
+		IIO_CHAN_SOFT_TIMESTAMP(1),				\
+	};								\
+
+#define ADC081C_NUM_CHANNELS 2
+
+struct adcxx1c_model {
+	const struct iio_chan_spec* channels;
+	int bits;
+};
+
+#define ADCxx1C_MODEL(_name, _bits)					\
+	{								\
+		.channels = _name ## _channels,				\
+		.bits = (_bits),					\
+	}
+
+DEFINE_ADCxx1C_CHANNELS(adc081c,  8);
+DEFINE_ADCxx1C_CHANNELS(adc101c, 10);
+DEFINE_ADCxx1C_CHANNELS(adc121c, 12);
+
+/* Model ids are indexes in _models array */
+enum adcxx1c_model_id {
+	ADC081C = 0,
+	ADC101C = 1,
+	ADC121C = 2,
+};
+
+static struct adcxx1c_model adcxx1c_models[] = {
+	ADCxx1C_MODEL(adc081c,  8),
+	ADCxx1C_MODEL(adc101c, 10),
+	ADCxx1C_MODEL(adc121c, 12),
 };
 
 static const struct iio_info adc081c_info = {
@@ -65,11 +126,30 @@ static const struct iio_info adc081c_info = {
 	.driver_module = THIS_MODULE,
 };
 
+static irqreturn_t adc081c_trigger_handler(int irq, void *p)
+{
+	struct iio_poll_func *pf = p;
+	struct iio_dev *indio_dev = pf->indio_dev;
+	struct adc081c *data = iio_priv(indio_dev);
+	u16 buf[8]; /* 2 bytes data + 6 bytes padding + 8 bytes timestamp */
+	int ret;
+
+	ret = i2c_smbus_read_word_swapped(data->i2c, REG_CONV_RES);
+	if (ret < 0)
+		goto out;
+	buf[0] = ret;
+	iio_push_to_buffers_with_timestamp(indio_dev, buf, iio_get_time_ns());
+out:
+	iio_trigger_notify_done(indio_dev->trig);
+	return IRQ_HANDLED;
+}
+
 static int adc081c_probe(struct i2c_client *client,
 			 const struct i2c_device_id *id)
 {
 	struct iio_dev *iio;
 	struct adc081c *adc;
+	struct adcxx1c_model *model = &adcxx1c_models[id->driver_data];
 	int err;
 
 	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WORD_DATA))
@@ -81,6 +161,7 @@ static int adc081c_probe(struct i2c_client *client,
 
 	adc = iio_priv(iio);
 	adc->i2c = client;
+	adc->bits = model->bits;
 
 	adc->ref = devm_regulator_get(&client->dev, "vref");
 	if (IS_ERR(adc->ref))
@@ -95,18 +176,26 @@ static int adc081c_probe(struct i2c_client *client,
 	iio->modes = INDIO_DIRECT_MODE;
 	iio->info = &adc081c_info;
 
-	iio->channels = &adc081c_channel;
-	iio->num_channels = 1;
+	iio->channels = model->channels;
+	iio->num_channels = ADC081C_NUM_CHANNELS;
+
+	err = iio_triggered_buffer_setup(iio, NULL, adc081c_trigger_handler, NULL);
+	if (err < 0) {
+		dev_err(&client->dev, "iio triggered buffer setup failed\n");
+		goto err_regulator_disable;
+	}
 
 	err = iio_device_register(iio);
 	if (err < 0)
-		goto regulator_disable;
+		goto err_buffer_cleanup;
 
 	i2c_set_clientdata(client, iio);
 
 	return 0;
 
-regulator_disable:
+err_buffer_cleanup:
+	iio_triggered_buffer_cleanup(iio);
+err_regulator_disable:
 	regulator_disable(adc->ref);
 
 	return err;
@@ -118,13 +207,16 @@ static int adc081c_remove(struct i2c_client *client)
 	struct adc081c *adc = iio_priv(iio);
 
 	iio_device_unregister(iio);
+	iio_triggered_buffer_cleanup(iio);
 	regulator_disable(adc->ref);
 
 	return 0;
 }
 
 static const struct i2c_device_id adc081c_id[] = {
-	{ "adc081c", 0 },
+	{ "adc081c", ADC081C },
+	{ "adc101c", ADC101C },
+	{ "adc121c", ADC121C },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, adc081c_id);
@@ -132,6 +224,8 @@ MODULE_DEVICE_TABLE(i2c, adc081c_id);
 #ifdef CONFIG_OF
 static const struct of_device_id adc081c_of_match[] = {
 	{ .compatible = "ti,adc081c" },
+	{ .compatible = "ti,adc101c" },
+	{ .compatible = "ti,adc121c" },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, adc081c_of_match);
@@ -149,5 +243,5 @@ static struct i2c_driver adc081c_driver = {
 module_i2c_driver(adc081c_driver);
 
 MODULE_AUTHOR("Thierry Reding <thierry.reding@avionic-design.de>");
-MODULE_DESCRIPTION("Texas Instruments ADC081C021/027 driver");
+MODULE_DESCRIPTION("Texas Instruments ADC081C/ADC101C/ADC121C driver");
 MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/adc/vf610_adc.c b/drivers/iio/adc/vf610_adc.c
index b10f629cc44b..653bf1379d2e 100644
--- a/drivers/iio/adc/vf610_adc.c
+++ b/drivers/iio/adc/vf610_adc.c
@@ -714,19 +714,19 @@ static int vf610_write_raw(struct iio_dev *indio_dev,
 	int i;
 
 	switch (mask) {
-		case IIO_CHAN_INFO_SAMP_FREQ:
-			for (i = 0;
-				i < ARRAY_SIZE(info->sample_freq_avail);
-				i++)
-				if (val == info->sample_freq_avail[i]) {
-					info->adc_feature.sample_rate = i;
-					vf610_adc_sample_set(info);
-					return 0;
-				}
-			break;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		for (i = 0;
+			i < ARRAY_SIZE(info->sample_freq_avail);
+			i++)
+			if (val == info->sample_freq_avail[i]) {
+				info->adc_feature.sample_rate = i;
+				vf610_adc_sample_set(info);
+				return 0;
+			}
+		break;
 
-		default:
-			break;
+	default:
+		break;
 	}
 
 	return -EINVAL;