diff options
author | Geert Uytterhoeven <geert+renesas@glider.be> | 2019-07-11 15:03:59 +0200 |
---|---|---|
committer | Stephen Boyd <sboyd@kernel.org> | 2019-07-22 15:04:54 -0700 |
commit | e1f1ae8002e4b06addc52443fcd975bbf554ae92 (patch) | |
tree | 67568f93bc1e1b799e49d09d6725f880fcc6e190 /drivers/clk/renesas | |
parent | c9a67cbb5189e966c70451562b2ca4c3876ab546 (diff) | |
download | linux-e1f1ae8002e4b06addc52443fcd975bbf554ae92.tar.bz2 |
clk: renesas: cpg-mssr: Fix reset control race condition
The module reset code in the Renesas CPG/MSSR driver uses
read-modify-write (RMW) operations to write to a Software Reset Register
(SRCRn), and simple writes to write to a Software Reset Clearing
Register (SRSTCLRn), as was mandated by the R-Car Gen2 and Gen3 Hardware
User's Manuals.
However, this may cause a race condition when two devices are reset in
parallel: if the reset for device A completes in the middle of the RMW
operation for device B, device A may be reset again, causing subtle
failures (e.g. i2c timeouts):
thread A thread B
-------- --------
val = SRCRn
val |= bit A
SRCRn = val
delay
val = SRCRn (bit A is set)
SRSTCLRn = bit A
(bit A in SRCRn is cleared)
val |= bit B
SRCRn = val (bit A and B are set)
This can be reproduced on e.g. Salvator-XS using:
$ while true; do i2cdump -f -y 4 0x6A b > /dev/null; done &
$ while true; do i2cdump -f -y 2 0x10 b > /dev/null; done &
i2c-rcar e6510000.i2c: error -110 : 40000002
i2c-rcar e66d8000.i2c: error -110 : 40000002
According to the R-Car Gen3 Hardware Manual Errata for Rev.
0.80 of Feb 28, 2018, reflected in Rev. 1.00 of the R-Car Gen3 Hardware
User's Manual, writes to SRCRn do not require read-modify-write cycles.
Note that the R-Car Gen2 Hardware User's Manual has not been updated
yet, and still says a read-modify-write sequence is required. According
to the hardware team, the reset hardware block is the same on both R-Car
Gen2 and Gen3, though.
Hence fix the issue by replacing the read-modify-write operations on
SRCRn by simple writes.
Reported-by: Yao Lihua <Lihua.Yao@desay-svautomotive.com>
Fixes: 6197aa65c4905532 ("clk: renesas: cpg-mssr: Add support for reset control")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Linh Phung <linh.phung.jy@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Diffstat (limited to 'drivers/clk/renesas')
-rw-r--r-- | drivers/clk/renesas/renesas-cpg-mssr.c | 16 |
1 files changed, 2 insertions, 14 deletions
diff --git a/drivers/clk/renesas/renesas-cpg-mssr.c b/drivers/clk/renesas/renesas-cpg-mssr.c index 52bbb9ce3807..d4075b130674 100644 --- a/drivers/clk/renesas/renesas-cpg-mssr.c +++ b/drivers/clk/renesas/renesas-cpg-mssr.c @@ -572,17 +572,11 @@ static int cpg_mssr_reset(struct reset_controller_dev *rcdev, unsigned int reg = id / 32; unsigned int bit = id % 32; u32 bitmask = BIT(bit); - unsigned long flags; - u32 value; dev_dbg(priv->dev, "reset %u%02u\n", reg, bit); /* Reset module */ - spin_lock_irqsave(&priv->rmw_lock, flags); - value = readl(priv->base + SRCR(reg)); - value |= bitmask; - writel(value, priv->base + SRCR(reg)); - spin_unlock_irqrestore(&priv->rmw_lock, flags); + writel(bitmask, priv->base + SRCR(reg)); /* Wait for at least one cycle of the RCLK clock (@ ca. 32 kHz) */ udelay(35); @@ -599,16 +593,10 @@ static int cpg_mssr_assert(struct reset_controller_dev *rcdev, unsigned long id) unsigned int reg = id / 32; unsigned int bit = id % 32; u32 bitmask = BIT(bit); - unsigned long flags; - u32 value; dev_dbg(priv->dev, "assert %u%02u\n", reg, bit); - spin_lock_irqsave(&priv->rmw_lock, flags); - value = readl(priv->base + SRCR(reg)); - value |= bitmask; - writel(value, priv->base + SRCR(reg)); - spin_unlock_irqrestore(&priv->rmw_lock, flags); + writel(bitmask, priv->base + SRCR(reg)); return 0; } |